The `neighbor <peer> version <X>` command does not
exist. I am unable to find it going back to version
2.0 of FRR. So this command has been not in the system
for a very long time.
In any event bgp already supports version 4 of bgp and
it auto-negotiates this.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Add the ability to specify the router-id/area-id when deleting the debug
ospf6 configuration.
The new commands are as follow:
no debug ospf6 border-routers router-id [A.B.C.D]
no debug ospf6 border-routers area-id [A.B.C.D]
Update the doc as well.
Signed-off-by: Ahmad Caracalli <ahmad.caracalli@6wind.com>
Implement NSSA address ranges as specified by RFC 3101:
NSSA border routers may be configured with Type-7 address ranges.
Each Type-7 address range is defined as an [address,mask] pair. Many
separate Type-7 networks may fall into a single Type-7 address range,
just as a subnetted network is composed of many separate subnets.
NSSA border routers may aggregate Type-7 routes by advertising a
single Type-5 LSA for each Type-7 address range. The Type-5 LSA
resulting from a Type-7 address range match will be distributed to
all Type-5 capable areas.
Syntax:
area A.B.C.D nssa range X:X::X:X/M [<not-advertise|cost (0-16777215)>]
Example:
router ospf6
ospf6 router-id 1.1.1.1
area 1 nssa
area 1 nssa range 2001:db8:1000::/64
area 1 nssa range 2001:db8:2000::/64
!
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Extend the pathd documentation with more configuration examples, more
detailed and some graphics to help understand what pathd supports.
Signed-off-by: Javier Garcia <rampxxxx@gmail.com>
Add the "default-information-originate" option to the "area X nssa"
command. That option allows the origination of Type-7 default routes
on NSSA ABRs and ASBRs.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Considering that both the GR helper mode and restarting mode can be
enabled at the same time, the "graceful-restart helper-only" command
can be a bit misleading since it implies that only the helper mode
is enabled. Rename the command to "graceful-restart helper enable"
to clarify what the command does.
Start a deprecation cycle of one year before removing the original
command
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Because vrf backend may be based on namespaces, each vrf can
use in the [16-(2^32-1)] range table identifier for daemons that
request it. Extend the table manager to be hosted by vrf.
That possibility is disabled in the case the vrf backend is vrflite.
In that case, all vrf context use the same table manager instance.
Add a configuration command to be able to configure the wished
range of tables to use. This is a solution that permits to give
chunks to bgp daemon when it works with bgp flowspec entries and
wants to use specific iptables that do not override vrf tables.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Considering that both the GR helper mode and restarting mode can be
enabled at the same time, the "graceful-restart helper-only" command
can be a bit misleading since it implies that only the helper mode
is enabled. Rename the command to "graceful-restart helper enable"
to clarify what the command does.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Issue #9535 describes how the export-list/import-list commands work
differently on ospfd and ospf6d.
In short:
* On ospfd, "area A.B.C.D export-list" filters which internal
routes an ABR exports to other areas. On ospf6d, instead, that
command filters which inter-area routes an ABR exports to the
configured area (which is quite counter-intuitive). In other words,
both commands do the same but in opposite directions.
* On ospfd, "area A.B.C.D import-list" filters which inter-area
routes an ABR imports into the configured area. On ospf6d, that
command filters which inter-area routes an interior router accepts.
* On both daemons, "area A.B.C.D filter-list prefix NAME <in|out>"
works exactly the same as import/export lists, but using prefix-lists
instead of ACLs.
The inconsistency on how those commands work is undesirable. This
PR proposes to adapt the ospf6d commands to behave like they do
in ospfd.
These changes are obviously backward incompatible and this PR doesn't
propose any mitigation strategy other than warning users about the
changes in the next release notes. Since these ospf6d commands are
undocumented and work in such a peculiar way, it's unlikely many
users will be affected (if any at all).
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
RFC 5187 specifies the Graceful Restart enhancement to the OSPFv3
routing protocol. This commit implements support for the GR
restarting mode.
Here's a quick summary of how the GR restarting mode works:
* GR can be enabled on a per-instance basis using the `graceful-restart
[grace-period (1-1800)]` command;
* To perform a graceful shutdown, the `graceful-restart prepare ipv6
ospf` EXEC-level command needs to be issued before restarting the
ospf6d daemon (there's no specific requirement on how the daemon
should be restarted);
* `graceful-restart prepare ospf` will initiate the graceful restart
for all GR-enabled instances by taking the following actions:
o Flooding Grace-LSAs over all interfaces
o Freezing the OSPF routes in the RIB
o Saving the end of the grace period in non-volatile memory (a JSON
file stored in `$frr_statedir`)
* Once ospf6d is started again, it will follow the procedures
described in RFC 3623 until it detects it's time to exit the graceful
restart (either successfully or unsuccessfully).
Testing done:
* New topotest featuring a multi-area OSPF topology (including stub
and NSSA areas);
* Successful interop tests against IOS-XR routers acting as helpers.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Added references to some other sysctl knobs that influence behavior
significant to routers, e.g. arp_accept, arp_ignore, bc_forwarding.
Signed-off-by: Trey Aspelund <taspelund@nvidia.com>
Received user feedback that it was unclear how to get into the FRR
shell. Adding a snippet to the basic setup page to help clarify.
Signed-off-by: Trey Aspelund <taspelund@nvidia.com>
Currently the source IP parameter must be entered between destination IP
and destination port parameters. This is not obviously understandable
when you read such config so let's move the source parameter to the end
of the command line, after the whole list of destination parameters. We
can do this without any deprecation cycle as the parameter was introduced
just recently and isn't in any public release yet.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
Add a knob to turn a NSSA area into a totally stub area. In this
configuration a Type-3 default summary route is generated by default.
Syntax: `area A.B.C.D nssa no-summary`.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Add the ability to configure the source address of rpki
connection. Proposed vty command is to add below parameter:
rpki cache <address> source <bindaddr> <port> preference <pref>
rpki cache <address> source <bindaddr> <port> <usernamessh> ...
This works for both tcp and ssh connections. In case the source
address is not available yet, the rpki retry interval will retry
in a defined amount of time.
Rtrlib library is the library in charge of the binding of the
tcp/ssh connection, and applies the getaddrinfo() and bind()
operations to the passed parameter bindaddr to the respective
tcp_config/ssh_config structures.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Add the "metric" and "metric-type" options to the "redistribute"
command.
This is a small commit since the logic of setting the metric
value and type of external routes was already present due to the
implementation of the "default-information originate" command months
ago. This commit merely extends the "redistribute" command to
leverage that functionality.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
While defaults are good picks for "reasonable" guesses, min and max
range values really aren't. Operators and experimenters often like to
configure "unreasonable" values to stress test, tests boundary
conditions and explore innovations.
With that in mind, change all ranges to 1..max (of type).
While we're here add optional ignored values in the "no" CLI forms.
Signed-off-by: Christian Hopps <chopps@labn.net>
Currently the NSSA support is a separate section, but it should actually
be a description of the corresponding CLI command.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
Currently the debugging section is placed in the middle of the section
with various configuration commands.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
1. This check is absolutely useless. Nothing keeps user from deleting
the address right after this check.
2. This check prevents zebra from correctly reading the user config with
"set src" because of a race with interface startup (see #4249).
3. NO OPERATIONAL DATA USAGE ON VALIDATION STAGE.
Fixes#7319.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
Replaces next-hop-self keyword "all" with "force" to match the CLI.
Also mentions third-party next-hops will be bypassed by next-hop-self.
Signed-off-by: Trey Aspelund <taspelund@nvidia.com>
Adds a knob that sets the time between loc-rib scans for conditional
advertisement.
I chose the range (5-240) because 1 second seems dumb and too easy to
hurt yourself at even moderate scale, 5 seconds you can still hurt
yourself but I could see a use case for it, and 4 minutes should be
enough for anyone (tm)
Signed-off-by: Quentin Young <qlyoung@nvidia.com>
Making the interface holdtime range to 3.5 times the hello-time
As per 7761, Section 4.11:
The Holdtime in a Hello message should be set to
(3.5 * Hello_Period), giving a default value of 105 seconds.
Therefore providing the user also to configure max upto 3.5 times
the hello timer interval.
Signed-off-by: Mobashshera Rasool <mrasool@vmware.com>
While we do have `show ip prefix-list NAME A.B.C.D/M`, that doesn't
actually run the prefix list matching code. While the result would
hopefully be the same anyway, let's have a way to call the actual prefix
list match code and get a result.
(As an aside, this might be useful for scripting to do a quick "is this
prefix in that prefix list" check.)
Signed-off-by: David Lamparter <equinox@diac24.net>
RFC 3623 specifies the Graceful Restart enhancement to the OSPF
routing protocol. This PR implements support for the restarting mode,
whereas the helper mode was implemented by #6811.
This work is based on #6782, which implemented the pre-restart part
and settled the foundations for the post-restart part (behavioral
changes, GR exit conditions, and on-exit actions).
Here's a quick summary of how the GR restarting mode works:
* GR can be enabled on a per-instance basis using the `graceful-restart
[grace-period (1-1800)]` command;
* To perform a graceful shutdown, the `graceful-restart prepare ospf`
EXEC-level command needs to be issued before restarting the ospfd
daemon (there's no specific requirement on how the daemon should
be restarted);
* `graceful-restart prepare ospf` will initiate the graceful restart
for all GR-enabled instances by taking the following actions:
o Flooding Grace-LSAs over all interfaces
o Freezing the OSPF routes in the RIB
o Saving the end of the grace period in non-volatile memory (a JSON
file stored in `$frr_statedir`)
* Once ospfd is started again, it will follow the procedures
described in RFC 3623 until it detects it's time to exit the graceful
restart (either successfully or unsuccessfully).
Testing done:
* New topotest featuring a multi-area OSPF topology (including stub
and NSSA areas);
* Successful interop tests against IOS-XR routers acting as helpers.
Co-authored-by: GalaxyGorilla <sascha@netdef.org>
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
domainname is a merge conflict: it is duplicated, so delete it.
bgp content is a compille warning and wrongly display, so fix it.
Signed-off-by: anlancs <anlan_cs@tom.com>
Adding the "clear ipv6 ospf6 command" . It resets
the ospfv3 datastructures and clears the database
as well as route tables. It resets the neighborship
by restarting the interface state machine.
If the user wants to change the router-id, this
command updates the router-id to the latest static
router-id and starts the neighbor formation with
the new router-id.
Signed-off-by: Yash Ranjan <ranjany@vmware.com>
`log-filter WORD` was giving me a serious headache since it also matches
`log WORD` due to the way the CLI token handling works. This meant that
a mistyped `log something` command would silently be interpreted as a
filter string, causing me serious headscratching and WTFs until I
figured what was going on.
Remove this UX pitfall so noone else falls into it. (Since the command
was never saved to config, renaming it shouldn't cause trouble.)
[Also I apparently forgot to update the docs when I transferred this
over to the new zlog bits...]
TODO for a rainy day: since we collect all the CLI commands anyway, we
should warn somewhere for "2nd level ambiguous" commands like this.
Signed-off-by: David Lamparter <equinox@diac24.net>
These names are saved in current vtysh's memory, can't and needn't be saved into
configure file by watchfrr's 'vtysh -w`.
Signed-off-by: anlancs <anlan_cs@tom.com>
Add a terse option to show bgp summary to shorten output.
Do not show the following information about the BGP
instances: the number of RIB entries, the table version and the used memory.
The "terse" option can be used in combination with the "remote-as", "neighbor",
"failed" and "established" filters, and with the "wide" option as well.
Before patch:
ubuntu# show bgp summary remote-as 123456
IPv4 Unicast Summary (VRF default):
BGP router identifier X.X.X.X, local AS number XXX vrf-id 0
BGP table version 0
RIB entries 3, using 552 bytes of memory
Peers 5, using 3635 KiB of memory
Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd PfxSnt Desc
10.200.200.2 4 123456 81432 4 0 56092 0 00:00:13 572106 0 N/A
Displayed neighbors 1
Total number of neighbors 4
IPv6 Unicast Summary (VRF default):
BGP router identifier X.X.X.X, local AS number XXX vrf-id 0
BGP table version 0
RIB entries 3, using 552 bytes of memory
Peers 5, using 3635 KiB of memory
Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd PfxSnt Desc
% No matching neighbor
Total number of neighbors 5
After patch:
ubuntu# show bgp summary remote-as 123456 terse
IPv4 Unicast Summary (VRF default):
BGP router identifier X.X.X.X, local AS number XXX vrf-id 0
Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd PfxSnt Desc
10.200.200.2 4 123456 81432 4 0 56092 0 00:00:13 572106 0 N/A
Displayed neighbors 1
Total number of neighbors 4
IPv6 Unicast Summary (VRF default):
BGP router identifier X.X.X.X, local AS number XXX vrf-id 1
% No matching neighbor
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
similarly to what was done for IS-IS in commit 01d43141, combine
the SRGB and SRLB commands for OSPF-SR, so that we can replace
overlapping ranges in one sweep change.
Also allow the range configuration to be stored before SR is enabled.
There is no reason why we should not - in fact that constraint meant
that we were always requesting the default label ranges regardless
of what we actually wanted to use.
Finally, update the topotests now that we do not need to refresh
the SRGB/SRLB/MSD after disabling SR. Note that the prefix-sid still
needs to be re-added.
Signed-off-by: Emanuele Di Pascale <emanuele@voltanet.io>
Modify VRF/view display in show bgp summary:
- to be more concise
- to display on which VRF/view no neighbor was found
Before patch:
ubuntu# show bgp vrf all summary
Instance default:
IPv4 Unicast Summary:
BGP router identifier XX.XX.XX.XX, local AS number XXXX vrf-id 0
(...)
IPv6 Unicast Summary:
Instance private:
IPv4 Unicast Summary:
ubuntu# show bgp vrf all ipv4 multicast summary
% No BGP neighbors found
% No BGP neighbors found
After patch:
ubuntu# show bgp vrf all summary
IPv4 Unicast Summary (VRF default):
BGP router identifier XX.XX.XX.XX, local AS number XXXX vrf-id 0
(...)
IPv6 Unicast Summary (VRF default):
(...)
IPv4 Unicast Summary (VRF private):
(...)
ubuntu# show bgp vrf all ipv4 multicast summary
% No BGP neighbors found in VRF default
% No BGP neighbors found in VRF private
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
"ip nht resolve-via-default" is currently placed in "Link Parameters
Commands" section. Add a separate section and missing IPv6 counterpart.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
Add ability to filter session on show bgp summary by neighbor or
remote AS:
ubuntu# show bgp summary ?
neighbor Show only the specified neighbor session
remote-as Show only the specified remote AS session
ubuntu# show bgp summary neighbor ?
A.B.C.D Neighbor to display information about
WORD Neighbor on BGP configured interface
X:X::X:X Neighbor to display information about
ubuntu# show bgp summary remote-as ?
(1-4294967295) AS number
external External (eBGP) AS sessions
internal Internal (iBGP) AS sessions
This patch includes the documentation and the topotest.
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
- As an example of pathd and igp (ospfd) config:
! igp ospfv2 snippet
interface eth0
ip ospf network point-to-point
!
router ospf$
mpls-te on
mpls-te export
...
!pathd snippet
segment-routing
traffic-eng
mpls-te on
mpls-te import ospfv2
segment-list sl-1
index 10 nai adjacency 10.1.2.11 10.1.2.1
index 20 nai adjacency 10.1.20.1 10.1.20.2
index 30 nai adjacency 10.2.5.2 10.2.5.5
!
policy color 5 endpoint 10.10.10.5
name five
binding-sid 5555
candidate-path preference 600 name cp51 explicit segment-list sl-1
candidate-path preference 500 name cp52-dyn dynamic
Signed-off-by: Javier Garcia <javier.garcia@voltanet.io>
Description:
Added a new show command("show ip zebra route dump") to dump all routes
with detailed information including nexthops,flags, status ..etc.
This helps for dubugging and added to support_bundle_command.conf.
Defined this command as a hidden command.
Signed-off-by: Rajesh Girada <rgirada@vmware.com>
Problem Statement:
=================
In scale setup BGP sessions start flapping.
RCA:
====
In virtualized environment there are multiple places where
MTU need to be set. If there are some places were MTU is not set
properly then there is chances that BGP packets get fragmented,
in scale setup this will lead to BGP session flap.
Fix:
====
A new tcp option is provided as part of this implementation,
which can be configured per neighbor and helps to set the TCP
max segment size. User need to derive the path MTU between the BGP
neighbors and set that value as part of tcp-mss setting.
1. CLI Configuration:
[no] neighbor <A.B.C.D|X:X::X:X|WORD> tcp-mss (1-65535)
2. Running config
frr# show running-config
router bgp 100
neighbor 198.51.100.2 tcp-mss 150 => new entry
neighbor 2001:DB8::2 tcp-mss 400 => new entry
3. Show command
frr# show bgp neighbors 198.51.100.2
BGP neighbor is 198.51.100.2, remote AS 100, local AS 100, internal link
Hostname: frr
Configured tcp-mss is 150, synced tcp-mss is 138 => new display
4. Show command json output
frr# show bgp neighbors 2001:DB8::2 json
{
"2001:DB8::2":{
"remoteAs":100,
"bgpTimerKeepAliveIntervalMsecs":60000,
"bgpTcpMssConfigured":400, => new entry
"bgpTcpMssSynced":388, => new entry
Risk:
=====
Low - This is a config driven feature and it sets the max segment
size for the TCP session between BGP peers.
Tests Executed:
===============
Have done manual testing with three router topology.
1. Executed basic config and un config scenarios
2. Verified if the config is updated in running config
during config and no config operation
3. Verified the show command output in both CLI format and
JSON format.
4. Verified if TCP SYN messages carry the max segment size
in their initial packets.
5. Verified the behaviour during clear bgp session.
6. done packet capture to see if the new segment size
takes effect.
Signed-off-by: Abhinay Ramesh <rabhinay@vmware.com>
Currently we have a "route-map optimization" command which is entered
from inside the route-map entry but actually applies to the whole
route-map. In addition, this command is not shown in the running-config
and not stored to the startup-config during "write".
Let's add a new command on the config node level to control this setting
and show it in the running-config to make possible to save it during
"write".
The old command is saved for the backward compatibility but hidden and
marked as deprecated.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
Most of these are many, many years out of date. All of them vary
randomly in quality. They show up by default in packages where they
aren't really useful now that we use integrated config. Remove them.
The useful ones have been moved to the docs.
Signed-off-by: Quentin Young <qlyoung@nvidia.com>
increase the maximum number of neighbors in a bgp group.
Set the maximum value to 50000 instead of 5000.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Add docs for commands to display BGP table per-RD.
Also update commands to mention flowspec, routes,
advertised-routes, and received-routes.
Signed-off-by: Trey Aspelund <taspelund@nvidia.com>
Description:
OSPF does not have an option to control the maximum multiple
equal cost paths to reach a destination/route(ECMP).
Currently, it is using the system specific max multiple paths.
But Somtimes, It requires to control the multiple paths from ospf.
This cli helps to configure the max number multiple paths in ospf.
Signed-off-by: Rajesh Girada <rgirada@vmware.com>
Before the transition of prefix-lists to northbound, this setting
controlled whether sequence numbers were displayed in the config.
After the transition, sequence numbers are always displayed in the
configuration, and this command only controls the output of the show
commands, which is not very useful. This command is not even shown in
the config anymore.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
This new BGP configuration is akin to "bgp bestpath aspath
multipath-relax". When applied, paths learned from different peer types
will be eligible to be considered for multipath (ECMP). Paths from all
of eBGP, iBGP, and confederation peers may be included in multipaths
if they are otherwise equal cost.
This change preserves the existing bestpath behavior of step 10's result
being returned, not the result from steps 8 and 9, in the case where
both 8+9 and 10 determine a winner.
Signed-off-by: Joanne Mikkelson <jmmikkel@arista.com>
Add new feature and commands to sharpd in order to collect Traffic Engineering
Database information from an IGP (OSPF or IS-IS) though the ZAPI Opaque
Message and the support of the Link State Library.
This feature serves as an example of how to code a Traffic Engineering
Database consumer and tests the mechanism.
Signed-off-by: Olivier Dugeon <olivier.dugeon@orange.com>
This patch allows to store Link State Information received through the various
LSAs into a dedicated Traffic Engineering Database (TED). This feature is
automatically activated once mpls-te is enabled.
A new CLI command `mpls-te export` permits to export the TED to other daemons
through the new ZAPI Opaque Link State messages. In complement, a new CLI
command `show ip ospf mpls-te database ...` output the contains of the TED to
the console.
Major modifications take place in ospf_te.[c, h]. File ospf_zebra.c has been
modified to handle TED synchronisation request.
Signed-off-by: Olivier Dugeon <olivier.dugeon@orange.com>
Add docs for commands to display BGP table per-RD.
Also update commands to mention flowspec, routes,
advertised-routes, and received-routes.
Signed-off-by: Trey Aspelund <taspelund@nvidia.com>
Add sequence no option to bgp as-path list cli syntax.
Add sequence no to example config.
Add auto generated sequence no in running-config if its not
provided in config.
Signed-off-by: Chirag Shah <chirag@nvidia.com>
Currently there is a single interval for both RX and TX echo functions.
This commit introduces separate RX and TX timers for echo packets.
The main advantage is to be able to set the receive interval to zero
when we don't want to receive echo packets from the remote system.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
Echo-mode implementation is currently broken. Instead of sending packets
to it's own address, bfdd is sending echo packets to the peer's address.
It may seem to work when testing between two FRR instances, because FRR
loops back such packets, but no other implementation is supposed to do
that.
Let's warn users that the current implementation works only between two
FRR instances.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
when changing both ranges at the same time the order of the commands
matters, as we need to make sure that the intermediate state is valid.
This represents a problem when pushing configuration via frr-reload.
To fix this, the global-block command was extended to optionally
allow setting the local-block range as well. The local-block command
is deprecated with a 1-year notice.
Signed-off-by: Emanuele Di Pascale <emanuele@voltanet.io>
* Clarify which commands are applicable to which flavors of LFA;
* Explain the default prefix priority for different prefix types;
* Rearrange some command descriptions so that they appear in this
order: local LFA, remote LFA and then TI-LFA.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
These don't need to be documented, most of the time they are obvious,
when they aren't the behavior can just be described in the command
description.
Signed-off-by: Quentin Young <qlyoung@nvidia.com>
- Generate index entries automatically
- Remove manual command index entries
- Clean up a few other manual index entries
Signed-off-by: Quentin Young <qlyoung@nvidia.com>
Modify code to add JSON format output in show command.
"show ip igmp [vrf NAME] join" and "show ip igmp vrf all join" with proper formatting
Signed-off-by: Sai Gomathi <nsaigomathi@vmware.com>
People keep asking about the default unreachable route
in the linux vrf table. Add a bit of color about the
design choices and what is going on.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Modify code to add JSON format output in show command
"show ipv6 ospf6 interface prefix" with proper formating
Signed-off-by: Yash Ranjan <ranjany@vmware.com>
Modify code to add JSON format output in show command
"show ipv6 ospf6 route [<intra-area|inter-area|external-1|
external-2|X:X::X:X|X:X::X:X/M|detail|summary>]"
with proper formating
Signed-off-by: Yash Ranjan <ranjany@vmware.com>
The RFC 8212 changes keep being questioned. Update the documentation
a bit more to help the end user figure it out themselves?
At the very least I can just now quote the doc link for this section
when someone asks the question.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Implement the below 2 CLIs to clear the current data in the process
and neighbor data structure.
1. clear ip ospf process
2. clear ip ospf neighbor
Signed-off-by: Mobashshera Rasool <mrasool@vmware.com>
The current securing BGP and resource certification reference links lead
to a page not found. This patch fixes that by pointing to their
corresponding PDF format resources.
Signed-off-by: Carlos Goncalves <cgoncalves@redhat.com>
Updated the documentation clarifying that multiple addresses can be
specifyed via -l option.
Signed-off-by: "Adriano Marto Reis" <adrianomarto@gmail.com>
This command has been added in the context of
PIM BSM functionality. This command will clear the
data structs having bsr information.
Co-authored-by: Sarita Patra <saritap@vmware.com>
Signed-off-by: vishaldhingra <vdhingra@vmware.com>
This new dynamic module makes pathd behave as a PCC for dynamic candidate path
using the external library pcpelib https://github.com/volta-networks/pceplib .
The candidate paths defined as dynamic will trigger computation requests to the
configured PCE, and the PCE response will be used to update the policy.
It supports multiple PCE. The one with smaller precedence will be elected
as the master PCE, and only if the connection repeatedly fails, the PCC will
switch to another PCE.
Example of configuration:
segment-routing
traffic-eng
pcep
pce-config CONF
source-address ip 10.10.10.10
sr-draft07
!
pce PCE1
config CONF
address ip 1.1.1.1
!
pce PCE2
config CONF
address ip 2.2.2.2
!
pcc
peer PCE1 precedence 10
peer PCE2 precedence 20
!
!
!
!
Co-authored-by: Brady Johnson <brady@voltanet.io>
Co-authored-by: Emanuele Di Pascale <emanuele@voltanet.io>
Co-authored-by: GalaxyGorilla <sascha@netdef.org>
Co-authored-by: Javier Garcia <javier.garcia@voltanet.io>
Co-authored-by: Renato Westphal <renato@opensourcerouting.org>
Co-authored-by: Sebastien Merle <sebastien@netdef.org>
Signed-off-by: Sebastien Merle <sebastien@netdef.org>
This new daemon manages Segment-Routing Traffic-Engineering
(SR-TE) Policies and installs them into zebra. It provides
the usual yang support and vtysh commands to define or change
SR-TE Policies.
In a nutshell SR-TE Policies provide the possibility to steer
traffic through a (possibly dynamic) list of Segment Routing
segments to the endpoint of the policy. This list of segments
is part of a Candidate Path which again belongs to the SR-TE
Policy. SR-TE Policies are uniquely identified by their color
and endpoint. The color can be used to e.g. match BGP
communities on incoming traffic.
There can be multiple Candidate Paths for a single
policy, the active Candidate Path is chosen according to
certain conditions of which the most important is its
preference. Candidate Paths can be explicit (fixed list of
segments) or dynamic (list of segment comes from e.g. PCEP, see
below).
Configuration example:
segment-routing
traffic-eng
segment-list SL
index 10 mpls label 1111
index 20 mpls label 2222
!
policy color 4 endpoint 10.10.10.4
name POL4
binding-sid 104
candidate-path preference 100 name exp explicit segment-list SL
candidate-path preference 200 name dyn dynamic
!
!
!
There is an important connection between dynamic Candidate
Paths and the overall topic of Path Computation. Later on for
pathd a dynamic module will be introduced that is capable
of communicating via the PCEP protocol with a PCE (Path
Computation Element) which again is capable of calculating
paths according to its local TED (Traffic Engineering Database).
This dynamic module will be able to inject the mentioned
dynamic Candidate Paths into pathd based on calculated paths
from a PCE.
https://tools.ietf.org/html/draft-ietf-spring-segment-routing-policy-06
Co-authored-by: Sebastien Merle <sebastien@netdef.org>
Co-authored-by: Renato Westphal <renato@opensourcerouting.org>
Co-authored-by: GalaxyGorilla <sascha@netdef.org>
Co-authored-by: Emanuele Di Pascale <emanuele@voltanet.io>
Signed-off-by: Sebastien Merle <sebastien@netdef.org>
Some vendors only advertise EAD-per-ES routes i.e. they do not
advertise EAD-per-EVI routes. To interop with these vendors we need
to relax the dependancy on EAD-per-EVI routes to activate a remote ES-PE.
Sample config -
>>>>>>>>>>>>>>>>>>>>>>>>>>>>
router bgp 5553
address-family l2vpn evpn
disable-ead-evi-rx
>>>>>>>>>>>>>>>>>>>>>>>>>>>>
Ticket: CM-31177
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
Update these two daemons to include the new
ability for both bgp and sharpd to send extra informational
data to zebra.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Rename "debug isis ti-lfa" to "debug isis lfa". Having different
debug guards for different kinds of LFA (classic, remote and TI-LFA)
doesn't make sense since all LFA solutions share code to certain
extent.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
The bgpd --listenon option implies --no_kernel. This commit makes note
of that in the documentation.
Signed-off-by: Mathias Bøhn Grytemark <mathias@grytemark.no>
Add a startup-time option to limit the number of fds used
by the thread/event infrastructure. If nothing is configured,
the system ulimit is used.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
Many index entries used '[no] xxx' or 'no xxx', some had both
positive and 'no' forms. Clean that up mostly - index positive
form of commands only.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
Modify code to add JSON format output in show command
"show ipv6 ospf6 interface" with proper formating
Signed-off-by: Yash Ranjan <ranjany@vmware.com>
Modify code to add JSON format output in show command
"show ipv6 ospf6 interface traffic" with proper formating
Signed-off-by: Yash Ranjan <ranjany@vmware.com>
Modify code to add JSON format output in show command
"show ipv6 ospf6 redistribute" with proper formating
Signed-off-by: Yash Ranjan <ranjany@vmware.com>
Add a command that allows FRR to know it's being used with
an underlying asic offload, from the linux kernel perspective.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
As of now, the BGP user documentation does not explicitly mention how
to use IPv6. This commit adds documentation of the activate command to
the user documentation which is crucial to get IPv6 networks announced
using FRRouting.
Signed-off-by: Michael Hohl <me@michaelhohl.net>
There was an inconsistency in the characters used for the second
level of title/section hierarchy - fix it.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
Changes update the user documentation to include a description of the
now available commands to enable/disable route-flap dampening for peers
and peer groups.
Signed-off-by: David Schweizer <dschweizer@opensourcerouting.org>
Description:
Added json support to ospf lsdb command and its subcommands.
Added json to the following sub commands.
show ip ospf database json
show ip ospf database router json
show ip ospf database network json
show ip ospf database external json
show ip ospf database summary json
show ip ospf database asbr-summary json
show ip ospf database nssa-external json
show ip ospf databas max-age json
show ip ospf database self-originate json
Signed-off-by: Rajesh Girada <rgirada@vmware.com>
Added description and config commands for the various sub-features
introduced as a part of EVPN Multihoming.
Signed-off-by: Anuradha Karuppiah <anuradhak@nvidia.com>
Implemented as per the feature description given in the source link.
Descriprion:
The BGP conditional advertisement feature uses the non-exist-map or exist-map
and the advertise-map keywords of the neighbor advertise-map command in order
to track routes by the route prefix.
non-exist-map :
If a route prefix is not present in output of the non-exist-map command, then
the route specified by the advertise-map command is announced.
exist-map :
If a route prefix is present in output of the exist-map command, then the route
specified by the advertise-map command is announced.
The conditional BGP announcements are sent in addition to the normal
announcements that a BGP router sends to its peers.
The conditional advertisement process is triggered by the BGP scanner process,
which runs every 60 seconds. This means that the maximum time for the conditional
advertisement to take effect is 60 seconds. The conditional advertisement can take
effect sooner, depending on when the tracked route is removed from the BGP table
and when the next instance of the BGP scanner occurs.
Sample Configuration on DUT
---------------------------
Router2# show running-config
Building configuration...
Current configuration:
!
frr version 7.6-dev-MyOwnFRRVersion
frr defaults traditional
hostname router
log file /var/log/frr/bgpd.log
log syslog informational
hostname Router2
service integrated-vtysh-config
!
debug bgp updates in
debug bgp updates out
!
debug route-map
!
ip route 200.200.0.0/16 blackhole
ipv6 route 2001:db8::200/128 blackhole
!
interface enp0s9
ip address 10.10.10.2/24
!
interface enp0s10
ip address 10.10.20.2/24
!
interface lo
ip address 2.2.2.2/24
ipv6 address 2001:db8::2/128
!
router bgp 2
bgp log-neighbor-changes
no bgp ebgp-requires-policy
neighbor 10.10.10.1 remote-as 1
neighbor 10.10.20.3 remote-as 3
!
address-family ipv4 unicast
network 2.2.2.0/24
network 200.200.0.0/16
neighbor 10.10.10.1 soft-reconfiguration inbound
neighbor 10.10.10.1 advertise-map ADVERTISE non-exist-map CONDITION
neighbor 10.10.20.3 soft-reconfiguration inbound
exit-address-family
!
address-family ipv6 unicast
network 2001:db8::2/128
network 2001:db8::200/128
neighbor 10.10.10.1 activate
neighbor 10.10.10.1 soft-reconfiguration inbound
neighbor 10.10.10.1 advertise-map ADVERTISE_6 non-exist-map CONDITION_6
neighbor 10.10.20.3 activate
neighbor 10.10.20.3 soft-reconfiguration inbound
exit-address-family
!
access-list CONDITION seq 5 permit 3.3.3.0/24
access-list ADVERTISE seq 5 permit 2.2.2.0/24
access-list ADVERTISE seq 6 permit 200.200.0.0/16
access-list ADVERTISE seq 7 permit 20.20.0.0/16
!
ipv6 access-list ADVERTISE_6 seq 5 permit 2001:db8::2/128
ipv6 access-list CONDITION_6 seq 5 permit 2001:db8::3/128
!
route-map ADVERTISE permit 10
match ip address ADVERTISE
!
route-map CONDITION permit 10
match ip address CONDITION
!
route-map ADVERTISE_6 permit 10
match ipv6 address ADVERTISE_6
!
route-map CONDITION_6 permit 10
match ipv6 address CONDITION_6
!
line vty
!
end
Router2#
Withdraw when non-exist-map prefixes present in BGP table:
----------------------------------------------------------
Router2# show ip bgp all wide
For address family: IPv4 Unicast
BGP table version is 8, local router ID is 2.2.2.2, vrf id 0
Default local pref 100, local AS 2
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 1.1.1.0/24 10.10.10.1 0 0 1 i
*> 2.2.2.0/24 0.0.0.0 0 32768 i
*> 3.3.3.0/24 10.10.20.3 0 0 3 i
*> 200.200.0.0/16 0.0.0.0 0 32768 i
Displayed 4 routes and 4 total paths
For address family: IPv6 Unicast
BGP table version is 8, local router ID is 2.2.2.2, vrf id 0
Default local pref 100, local AS 2
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 2001:db8::1/128 fe80::a00:27ff:fecb:ad57 0 0 1 i
*> 2001:db8::2/128 :: 0 32768 i
*> 2001:db8::3/128 fe80::a00:27ff:fe76:6738 0 0 3 i
*> 2001:db8::200/128 :: 0 32768 i
Displayed 4 routes and 4 total paths
Router2#
Router2# show ip bgp neighbors 10.10.10.1
BGP neighbor is 10.10.10.1, remote AS 1, local AS 2, external link
!--- Output suppressed.
For address family: IPv4 Unicast
Update group 9, subgroup 5
Packet Queue length 0
Inbound soft reconfiguration allowed
Community attribute sent to this neighbor(all)
Condition NON_EXIST, Condition-map *CONDITION, Advertise-map *ADVERTISE, status: Withdraw
1 accepted prefixes
For address family: IPv6 Unicast
Update group 10, subgroup 6
Packet Queue length 0
Inbound soft reconfiguration allowed
Community attribute sent to this neighbor(all)
Condition NON_EXIST, Condition-map *CONDITION_6, Advertise-map *ADVERTISE_6, status: Withdraw
1 accepted prefixes
!--- Output suppressed.
Router2#
Here 2.2.2.0/24 & 200.200.0.0/16 (prefixes in advertise-map) are withdrawn
by conditional advertisement scanner as the prefix(3.3.3.0/24) specified
by non-exist-map is present in BGP table.
Router2# show ip bgp all neighbors 10.10.10.1 advertised-routes wide
For address family: IPv4 Unicast
BGP table version is 8, local router ID is 2.2.2.2, vrf id 0
Default local pref 100, local AS 2
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 1.1.1.0/24 0.0.0.0 0 1 i
*> 3.3.3.0/24 0.0.0.0 0 3 i
Total number of prefixes 2
For address family: IPv6 Unicast
BGP table version is 8, local router ID is 2.2.2.2, vrf id 0
Default local pref 100, local AS 2
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 2001:db8::1/128 :: 0 1 i
*> 2001:db8::3/128 :: 0 3 i
*> 2001:db8::200/128 :: 0 32768 i
Total number of prefixes 3
Router2#
Advertise when non-exist-map prefixes not present in BGP table:
---------------------------------------------------------------
After Removing 3.3.3.0/24 (prefix present in non-exist-map),
2.2.2.0/24 & 200.200.0.0/16 (prefixes present in advertise-map) are advertised
Router2# show ip bgp all wide
For address family: IPv4 Unicast
BGP table version is 9, local router ID is 2.2.2.2, vrf id 0
Default local pref 100, local AS 2
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 1.1.1.0/24 10.10.10.1 0 0 1 i
*> 2.2.2.0/24 0.0.0.0 0 32768 i
*> 200.200.0.0/16 0.0.0.0 0 32768 i
Displayed 3 routes and 3 total paths
For address family: IPv6 Unicast
BGP table version is 9, local router ID is 2.2.2.2, vrf id 0
Default local pref 100, local AS 2
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 2001:db8::1/128 fe80::a00:27ff:fecb:ad57 0 0 1 i
*> 2001:db8::2/128 :: 0 32768 i
*> 2001:db8::200/128 :: 0 32768 i
Displayed 3 routes and 3 total paths
Router2#
Router2# show ip bgp neighbors 10.10.10.1
!--- Output suppressed.
For address family: IPv4 Unicast
Update group 9, subgroup 5
Packet Queue length 0
Inbound soft reconfiguration allowed
Community attribute sent to this neighbor(all)
Condition NON_EXIST, Condition-map *CONDITION, Advertise-map *ADVERTISE, status: Advertise
1 accepted prefixes
For address family: IPv6 Unicast
Update group 10, subgroup 6
Packet Queue length 0
Inbound soft reconfiguration allowed
Community attribute sent to this neighbor(all)
Condition NON_EXIST, Condition-map *CONDITION_6, Advertise-map *ADVERTISE_6, status: Advertise
1 accepted prefixes
!--- Output suppressed.
Router2#
Router2# show ip bgp all neighbors 10.10.10.1 advertised-routes wide
For address family: IPv4 Unicast
BGP table version is 9, local router ID is 2.2.2.2, vrf id 0
Default local pref 100, local AS 2
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 1.1.1.0/24 0.0.0.0 0 1 i
*> 2.2.2.0/24 0.0.0.0 0 32768 i
*> 200.200.0.0/16 0.0.0.0 0 32768 i
Total number of prefixes 3
For address family: IPv6 Unicast
BGP table version is 9, local router ID is 2.2.2.2, vrf id 0
Default local pref 100, local AS 2
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 2001:db8::1/128 :: 0 1 i
*> 2001:db8::2/128 :: 0 32768 i
*> 2001:db8::200/128 :: 0 32768 i
Total number of prefixes 3
Router2#
Signed-off-by: Madhuri Kuruganti <k.madhuri@samsung.com>
Add a type specifier to the `show nexthop-group` command
so we can easily filter by type when using proto created
nexthop groups.
Signed-off-by: Stephen Worley <sworley@cumulusnetworks.com>
Add the "n-flag-clear" option to the "segment-routing prefix"
command. The only thing that option does is to clear the node
flag of the Prefix-SID, even if it corresponds to a local loopback
address. No changes are necessary other than that in order to fully
support Anycast-SIDs. isisd already supports multiple routers
advertising the same route with the same Prefix-SID after the recent
refactoring. Clearing the node flag for such anycast routes isn't
strictly required, but failure to do so can lead to problems like
TI-LFA picking the wrong Prefix-SID when calculating repair paths.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Embed Prefix-SID information inside SPF data structures so that
Prefix-SIDs can be installed together with their associated routes
at the end of the SPF algorithm. This is different from the current
implementation where Prefix-SIDs are parsed and processed separately,
which is vastly suboptimal.
Advantages of the new code:
* No need to parse the LSPDB an additional time to detect and process
SR-related changes;
* Routes are installed with their Prefix-SID labels in the same ZAPI
message. This can prevent packet dropping for a few milliseconds
after each SPF run if there are BGP-labeled routes (e.g. L3VPN) that
recurse on IGP labeled routes;
* Much easier to support Anycast-SIDs, as the SPF code will naturally
figure out the best nexthops and use only them (that can't be done
in any reasonable way if the Prefix-SID Sub-TVLs are processed
separately);
* Less code to maintain and reduced memory footprint;
The "show isis segment-routing prefix-sids" command was removed as
it doesn't make sense anymore now that "show isis route" exists.
Prefix-SIDs are a property of routes, so what was done was to extend
the "show isis route" command with a new "prefix-sid" option that
changes the output table to show the Prefix-SID information associated
to each route.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Add an option to remove RPATH entry from binary files.
Useful for cross-compilation, otherwise libtool hardcodes
the building path.
Signed-off-by: Emanuele Bovisio <emanuele.bovisio@eolo.it>
Changes update the user documentation to include descriptions of the RFC
4271 DelayOpenTimer VTY shell commands.
Signed-off-by: David Schweizer <dschweizer@opensourcerouting.org>
nhrp: Configure vici socket path using
configure --with-vici-socket=/var/run/charon.vici
If not specified default to /var/run/charon.vici
Signed-off-by: Zoran Peričić <zpericic@netst.org>
Add a command `set installable` that allows configured nexthop
groups to be treated as separate/installable objects in the RIB.
A callback needs to be implemented per daemon to handle installing
the NHG into the rib via zapi when this command is set. This
patch includes the implementation for sharpd.
Signed-off-by: Stephen Worley <sworley@cumulusnetworks.com>
With the change of Solaris going from Supported -> UnSupported
the documentation needed to be updated to reflect the reality
on the ground.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Add support for a BGP-wide setting to enter and exit graceful shutdown.
This will apply to all BGP peers across all BGP instances. Per-instance
configuration is disallowed if the BGP-wide setting is in effect.
Signed-off-by: Vivek Venkatraman <vivek@nvidia.com>
Updated the user documentation to reflect changes made to routemaps "set
metric" VTY shell command.
Signed-off-by: David Schweizer <dschweizer@opensourcerouting.org>
a linux configuration gives some explanation on how to set up an evpn
overlay in network namespaces.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Add a blurb about the rpm package server in the overview page
so its easier to know where it is. Should be with the debian
one anyway.
Signed-off-by: Stephen Worley <sworley@cumulusnetworks.com>
Enhancement to update-delay configuration to allow setting globally
rather than per-instance. Setting the update-delay is allowed either
per-vrf or globally, but not both at the same time.
Ticket: CM-31096
Signed-off-by: Don Slice <dslice@nvidia.com>
* Added an entry in the user documentation for the BGP daemon no-rib
option vty shell commands.
Signed-off-by: David Schweizer <dschweizer@opensourcerouting.org>
1. Added isis with different vrf and it's dependecies.
2. Added new vrf leaf in yang.
3. A minor change for IF_DOWN_FROM_Z passing argrument is
replaced with ifp pointer in api "isis_if_delete_hook()".
4. Minor fix in the isisd spf unit test.
Co-authored-by: Kaushik <kaushik@niralnetworks.com>"
Signed-off-by: harios_niral <hari@niralnetworks.com>
Example configuration:
route-map SET_SR_POLICY permit 10
set sr-te color 1
!
router bgp 1
bgp router-id 1.1.1.1
neighbor 2.2.2.2 remote-as 1
neighbor 2.2.2.2 update-source lo
address-family ipv4 unicast
neighbor 2.2.2.2 next-hop-self
neighbor 2.2.2.2 route-map SET_SR_POLICY in
exit-address-family
!
!
Learned BGP routes from 2.2.2.2 are mapped to the SR-TE Policy
which is uniquely determined by the BGP nexthop (2.2.2.2 in this
case) and the SR-TE color in the route-map.
Co-authored-by: Renato Westphal <renato@opensourcerouting.org>
Co-authored-by: GalaxyGorilla <sascha@netdef.org>
Co-authored-by: Sebastien Merle <sebastien@netdef.org>
Signed-off-by: Sebastien Merle <sebastien@netdef.org>
Introduce the "show isis route" command to display the routes
associated to an SPF tree. Different from the "show ip route" command,
"show isis route" displays the L1 and L2 routes separately (and not
the best routes only).
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Some Sphinx apis have changed over time; test the installed
version and use the apis that match the version.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
The fuzzing code that is in the master branch is outdated and unused, so it
is worth to remove it to improve readablity of the code.
All the code related to the fuzzing is in the `fuzz` branch.
Signed-off-by: Jakub Urbańczyk <xthaid@gmail.com>
