There is no route-map set action to replace any ASN,
or a part of an ASN, with a configured ASN.
The current commit adds a new command to use a configured
ASN as replacement, instead of using the local as number.
> set as-path replace any 65500
Update the 'bgp_set_aspath_replace' test.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
It is not possible to flush all the incoming as-path list
from a given BGP update.
Add a route-map set command to remove all as-paths
from a given AS path. Add the necessary tests.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Looks like people don't find what does it mean (Policy) at first shot, let's
try giving more hints here.
Signed-off-by: Donatas Abraitis <donatas@opensourcerouting.org>
Currently, delayed reflooding on P2MP interfaces for LSAs received
from neighbors on the interface is unconditionally (see commit
c706f0e32b). In some cases, this
change wasn't desirable and this feature makes delayed reflooding
configurable for P2MP interfaces via the CLI command:
"ip ospf network point-to-multipoint delay-reflood" in interface
submode.
Signed-off-by: Acee <aceelindem@gmail.com>
`ccls` needs information from FRR build configuration to work,
so allow creation of a custom ccls config during autoconf.
Paraphrasing the doc entry: ccls is a very powerful tool that allows
dev environments to provide sophisticated IDE functionality, e.g.,
semantically aware jumps and code refactoring...
Signed-off-by: Christian Hopps <chopps@labn.net>
This command makes unplanned GR more reliable by manipulating the
sending of Grace-LSAs and Hello packets for a certain amount of time,
increasing the chance that the neighboring routers are aware of
the ongoing graceful restart before resuming normal OSPF operation.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
In practical terms, unplanned GR refers to the act of recovering
from a software crash without affecting the forwarding plane.
Unplanned GR and Planned GR work virtually the same, except for the
following difference: on planned GR, the router sends the Grace-LSAs
*before* restarting, whereas in unplanned GR the router sends the
Grace-LSAs immediately *after* restarting.
For unplanned GR to work, ospf6d was modified to send a
ZEBRA_CLIENT_GR_CAPABILITIES message to zebra as soon as GR is
enabled. This causes zebra to freeze the OSPF routes in the RIB as
soon as the ospf6d daemon dies, for as long as the configured grace
period (the defaults is 120 seconds). Similarly, ospf6d now stores in
non-volatile memory that GR is enabled as soon as GR is configured.
Those two things are no longer done during the GR preparation phase,
which only happens for planned GRs.
Unplanned GR will only take effect when the daemon is killed
abruptly (e.g. SIGSEGV, SIGKILL), otherwise all OSPF routes will be
uninstalled while ospf6d is exiting. Once ospf6d starts, it will
check whether GR is enabled and enter in the GR mode if necessary,
sending Grace-LSAs out all operational interfaces.
One disadvantage of unplanned GR is that the neighboring routers
might time out their corresponding adjacencies if ospf6d takes too
long to come back up. This is especially the case when short dead
intervals are used (or BFD). For this and other reasons, planned
GR should be preferred whenever possible.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
In practical terms, unplanned GR refers to the act of recovering
from a software crash without affecting the forwarding plane.
Unplanned GR and Planned GR work virtually the same, except for the
following difference: on planned GR, the router sends the Grace-LSAs
*before* restarting, whereas in unplanned GR the router sends the
Grace-LSAs immediately *after* restarting.
For unplanned GR to work, ospf6d was modified to send a
ZEBRA_CLIENT_GR_CAPABILITIES message to zebra as soon as GR is
enabled. This causes zebra to freeze the OSPF routes in the RIB as
soon as the ospfd daemon dies, for as long as the configured grace
period (the defaults is 120 seconds). Similarly, ospfd now stores in
non-volatile memory that GR is enabled as soon as GR is configured.
Those two things are no longer done during the GR preparation phase,
which only happens for planned GRs.
Unplanned GR will only take effect when the daemon is killed
abruptly (e.g. SIGSEGV, SIGKILL), otherwise all OSPF routes will
be uninstalled while ospfd is exiting. Once ospfd starts, it will
check whether GR is enabled and enter in the GR mode if necessary,
sending Grace-LSAs out all operational interfaces.
One disadvantage of unplanned GR is that the neighboring routers
might time out their corresponding adjacencies if ospfd takes too
long to come back up. This is especially the case when short dead
intervals are used (or BFD). For this and other reasons, planned
GR should be preferred whenever possible.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Until now, the bgp local paths were using the default null label
defined. It was not possible to select the null label for the ipv4
or the ipv6 address families.
This commit addresses this issues by adding two extra-parameters
to the BGP labeled-unicast command.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Let users know about the RIP BFD integration commands and increment the
used RFCs reference.
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
Debugging-isis tag was moved.
Move it to right place.
Fixes: 9389175b75 ("doc: add documentation for IS-IS Segment Routing")
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
