Reserve 128MiB of global CMA which is also marked as re-usable
so that OS can also use the same if peripheral drivers are not using the
same.
AM62x supports multimedia components such as GPU, dual Display and Camera.
Assuming the worst-case scenario where all 3 are run in parallel below
is the calculation :
1) OV5640 camera sensor supports 1920x1080 resolution
-> 1920 width x 1080 height x 2 bytesperpixel x 8 buffers
(default in yavta) : 32MiB
2) 1920x1200 Microtips LVDS panel supported
-> 1920 width x 1080 height x 4 bytesperpixel x 2 buffers :
16 MiB
3) 1920x1080 HDMI display supported
-> 1920 width x 1080 height x 4 bytesperpixel x 2 buffers :
15.82 MiB which is ~16 MiB
4) IMG GPU shares with display allocated buffers while rendering
but in case some dedicated operation viz color conversion,
keeping same window of ~16 MiB for GPU too.
Total is 80 MiB and adding 32 MiB for other peripherals and extra
16 MiB to keep as buffer for fragmentation thus rounding total to 128
MiB.
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Randolph Sapp <rs@ti.com>
Link: https://lore.kernel.org/r/20240613150902.2173582-2-devarsht@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Fix the following warnings when compiling dtbs with W=1:
../arch/arm64/boot/dts/ti/k3-am62x-sk-common.dtsi:343.10-353.6: Warning (graph_child_address): /bus@f0000/i2c@20000000/tps6598x@3f/connector/ports: graph node has single child node 'port@0', #address-cells/#size-cells are not necessary
../arch/arm64/boot/dts/ti/k3-am62-main.dtsi:633.22-643.5: Warning (graph_child_address): /bus@f0000/dwc3-usb@f900000/usb@31000000: graph node has single child node 'port@0', #address-cells/#size-cells are not necessary
Cc: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Tested-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240626101520.1782320-3-d-gole@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Fix the following warnings that are thrown when building dtbs with W=1:
../arch/arm64/boot/dts/ti/k3-am62p5-sk.dts:367.10-376.6: Warning (graph_child_address): /bus@f0000/i2c@20000000/usb-power-controller@3f/connector/ports: graph node has single child node 'port@0', #address-cells/#size-cells are not necessary
../arch/arm64/boot/dts/ti/k3-am62p-j722s-common-main.dtsi:647.22-657.5: Warning (graph_child_address): /bus@f0000/usb@f900000/usb@31000000: graph node has single child node 'port@0', #address-cells/#size-cells are not necessary
also defined at ../arch/arm64/boot/dts/ti/k3-am62p5-sk.dts:517.7-528.3
Cc: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240626101520.1782320-2-d-gole@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The AM67A/J722S/TDA4AEN platform is a derivative of AM62P platform
and we have no single 1:1 relation regarding index of GPIO and pin
controller. The GPIOs and pin controller registers have mapping and
holes in the map. These have been extracted from the J722S data
sheet. The MCU mapping is carried forward as is with J722S, however the
main GPIO block has differences that needs to be accounted for.
Mux mode input is selected as it is bi-directional. In case a specific
pull type or a specific pin level drive setting is desired, the board
device tree files will have to explicitly mux those pins for the GPIO
with the desired setting.
Ref: J722S Data sheet https://www.ti.com/lit/gpn/tda4aen-q1
Signed-off-by: Jared McArthur <j-mcarthur@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20240627162539.691223-4-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
On the AM62P platform we have no single 1:1 relation regarding index
of GPIO and pin controller. The GPIOs and pin controller registers
have mapping and holes in the map. These have been extracted from the
AM62P data sheet.
MCU pinctrl definition is shared as it is common between AM62P and
J722S, but that is not the case for main domain.
Ref: AM62P Data sheet https://www.ti.com/lit/gpn/am62p
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20240627162539.691223-3-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Introduce a GPIO mux mode macro for easier readability. All K3 devices
use mux mode 7 to switch to GPIO mux and this allows the gpio-ranges to
be defined for pinctrl-single clearly.
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20240627162539.691223-2-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The WKUP system controller address region contains an eFuse block with
MAC addresses to be used by the Ethernet controller. The property
“ti,syscon-efuse” contains a phandle to a syscon region and an offset
into this region where the MAC addresses can be found. Currently
"ti,syscon-efuse" points to the entire system controller address space
node with an offset to the eFuse IP address.
Instead add a cpsw-mac-efuse node to describe the exact eFuse area. Then
point the Ethernet controller directly to this region, no offset needed.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240628151518.40100-8-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The WKUP system controller address region contains an eFuse block with
MAC addresses to be used by the Ethernet controller. The property
“ti,syscon-efuse” contains a phandle to a syscon region and an offset
into this region where the MAC addresses can be found. Currently
"ti,syscon-efuse" points to the entire system controller address space
node with an offset to the eFuse IP address.
Instead add a cpsw-mac-efuse node to describe the exact eFuse area. Then
point the Ethernet controller directly to this region, no offset needed.
This makes it so the system controller memory area does not need to be one
big syscon area, describe this bus address area as the simple-bus it is.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240628151518.40100-7-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The MCU system controller address region contains an eFuse block with
MAC addresses to be used by the Ethernet controller. The property
“ti,syscon-efuse” contains a phandle to a syscon region and an offset
into this region where the MAC addresses can be found. Currently
"ti,syscon-efuse" points to the entire system controller address space
node with an offset to the eFuse IP address.
Instead add a cpsw-mac-efuse node to describe the exact eFuse area. Then
point the Ethernet controller directly to this region, no offset needed.
This makes it so the system controller memory area does not need to be one
big syscon area, describe this bus address area as the simple-bus it is.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240628151518.40100-6-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The MCU system controller address region contains an eFuse block with
MAC addresses to be used by the Ethernet controller. The property
“ti,syscon-efuse” contains a phandle to a syscon region and an offset
into this region where the MAC addresses can be found. Currently
"ti,syscon-efuse" points to the entire system controller address space
node with an offset to the eFuse IP address.
Instead add a cpsw-mac-efuse node to describe the exact eFuse area. Then
point the Ethernet controller directly to this region, no offset needed.
This makes it so the system controller memory area does not need to be one
big syscon area, describe this bus address area as the simple-bus it is.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240628151518.40100-5-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The MCU system controller address region contains an eFuse block with
MAC addresses to be used by the Ethernet controller. The property
“ti,syscon-efuse” contains a phandle to a syscon region and an offset
into this region where the MAC addresses can be found. Currently
"ti,syscon-efuse" points to the entire system controller address space
node with an offset to the eFuse IP address.
Instead add a cpsw-mac-efuse node to describe the exact eFuse area. Then
point the Ethernet controller directly to this region, no offset needed.
This makes it so the system controller memory area does not need to be one
big syscon area, describe this bus address area as the simple-bus it is.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240628151518.40100-4-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The MCU system controller address region contains an eFuse block with
MAC addresses to be used by the Ethernet controller. The property
“ti,syscon-efuse” contains a phandle to a syscon region and an offset
into this region where the MAC addresses can be found. Currently
"ti,syscon-efuse" points to the entire system controller address space
node with an offset to the eFuse IP address.
Instead add a cpsw-mac-efuse node to describe the exact eFuse area. Then
point the Ethernet controller directly to this region, no offset needed.
This makes it so the system controller memory area does not need to be one
big syscon area, describe this bus address area as the simple-bus it is.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240628151518.40100-3-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The MCU system controller address region contains an eFuse block with
MAC addresses to be used by the Ethernet controller. The property
“ti,syscon-efuse” contains a phandle to a syscon region and an offset
into this region where the MAC addresses can be found. Currently
"ti,syscon-efuse" points to the entire system controller address space
node with an offset to the eFuse IP address.
Instead add a cpsw-mac-efuse node to describe the exact eFuse area. Then
point the Ethernet controller directly to this region, no offset needed.
This makes it so the system controller memory area does not need to be one
big syscon area, describe this bus address area as the simple-bus it is.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240628151518.40100-2-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The phyCORE-AM62Ax [1] is a SoM (System on Module) featuring TI's AM62Ax SoC.
It can be used in combination with different carrier boards.
This module can come with different sizes and models for
DDR, eMMC, SPI NOR Flash and various SoCs from the AM62Ax family.
A development Kit, called phyBOARD-Lyra [2] is used as a carrier board
reference design with a mapper board being used to allow the phyCORE-AM62Ax
to fit the phyBOARD-Lyra.
Supported features:
* Debug UART
* SPI NOR Flash
* eMMC
* 2x Ethernet
* Micro SD card
* I2C EEPROM
* I2C RTC
* GPIO Expander
* LEDs
* USB
* HDMI
* USB-C
* Audio
For more details, see:
[1] Product page SoM: https://www.phytec.com/product/phycore-am62a
[2] Product page CB: https://www.phytec.com/product/phyboard-am62a
Signed-off-by: Garrett Giordano <ggiordano@phytec.com>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20240626155244.3311436-4-ggiordano@phytec.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
PHYTECs phyBOARD-Lyra carrier board is able to accomidate multiple SoMs.
Refactor k3-am625-phyboard-lyra-rdk.dts into an include file so it can
be reused in combination with our phyCORE-AM62Ax SoM.
Signed-off-by: Garrett Giordano <ggiordano@phytec.com>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20240626155244.3311436-2-ggiordano@phytec.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The audio support on J784S4-EVM is using PCM3168A[0] codec
connected to McASP0 serializers.
- Add the nodes for sound-card, audio codec, MAIN_I2C3 and
McASP0.
- Add pinmux for I2C3, McASP0 and AUDIO_EXT_REFCLK1.
- Add necessary GPIO hogs to route the MAIN_I2C3 lines and
McASP serializer.
- Add idle-state as 1 in mux1 to route McASP clock signals.
[0]: <https://www.ti.com/lit/gpn/pcm3168a>
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Link: https://lore.kernel.org/r/20240626101645.36764-4-j-choudhary@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
On J784S4 SoC, the AUDIO_REFCLK1 can be used as input to external
peripherals when configured through CTRL_MMR.
Add audio_refclk1 node which would be used as system clock for
audio codec PCM3168A.
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Link: https://lore.kernel.org/r/20240626101645.36764-3-j-choudhary@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add McASP 0-4 instances and keep them disabled because several
required properties are missing as they are board specific.
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Link: https://lore.kernel.org/r/20240626101645.36764-2-j-choudhary@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The NAND expansion card (PROC143E1) connects over the User/MCU/PRU
Expansion port on the am62-lp-sk EVM.
The following pins are shared between McASP1 and GPMC-NAND so
both cannot work simultaneously.
Pin name McASP1 function GPMC function
======== =============== =============
J17 MCASP1_AXR0 GPMC0_WEN
P21 MCASP1_AFSX GPMC0_WAIT0
K17 MCASP1_ACLKX GPMC0_BE0N_CLE
K20 MCASP1_AXR2 GPMC0_ADVN_ALE
The factory default sets the pins for McASP1 use. (i.e.
Resistor Array RA1 installed, RA4 not installed).
For NAND use, RA1 has to be removed and RA4 must be
installed.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240622-am62lp-sk-nand-v1-2-caee496eaf42@kernel.org
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The audio support on J722S-EVM is using TLV320AIC3106[0] codec
connected to McASP1 serializers.
- Add the nodes for sound-card, audio codec and McASP1.
- Add hog for TRC_MUX_SEL to select between McASP and TRACE signals
- Add hogs for GPIO_AUD_RSTn and MCASP1_FET_SEL which is used to
switch between HDMI audio and codec audio.
- Add pinmux for MCASP1 and AUDIO_EXT_REFCLK1.
[0]: <https://www.ti.com/lit/gpn/TLV320AIC3106>
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Reviewed-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240625113301.217369-3-j-choudhary@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
On J722S SoC, the AUDIO_REFCLK1 can be used as input to external
peripherals when configured through CTRL_MMR.
Add audio_refclk1 node which would be used as system clock for the
audio codec TLV320AIC3106.
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Link: https://lore.kernel.org/r/20240625113301.217369-2-j-choudhary@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
AM68 SK has an OSPI NOR flash on its SOM connected to OSPI0 instance.
Enable support for the same. Also, describe the OSPI flash partition
information through the device tree, according to the offsets in the
bootloader.
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20240622161835.3610348-1-u-kumar1@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add an overlay to change from the default OSPI NOR to QSPI NOR
for all am6xx-phycore-som boards.
The EEPROM on am6xx-phycore-soms contains information about the
configuration of the SOM. The standard configuration of the SOM
has an ospi nor, but if qspi nor is populated, the EEPROM will
indicate that change and we can use this overlay to cleanly change to
qspi nor.
Signed-off-by: Nathan Morrisson <nmorrisson@phytec.com>
Link: https://lore.kernel.org/r/20240621233143.2077941-1-nmorrisson@phytec.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
MIT license was added to the AM64x SoC DTSIs in commit 6248b20e32
("arm64: dts: ti: k3-am64: Add MIT license along with GPL-2.0"). Apply
the same license change to the TQMa64xxL SoM and MBaX4XxL baseboard
Device Trees.
The copyright year is updated to indicate the license change.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20240625110244.9881-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
I2C1 controller controls io-expander which provides power to voltage
regulator vdd_mmc1 for MMC SD using a gpio line.
Add bootph-all to the pinmux node for this instance, as this is used during
SPL stage too by the bootloader while using SD boot mode as without this
the SD boot mode fails with below error when using this device-tree in
u-boot:
"Timed out in wait_for_event: status=0000
Check if pads/pull-ups of bus are properly configured
Timed out in wait_for_event: status=0000
Check if pads/pull-ups of bus are properly configured
"
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Link: https://lore.kernel.org/r/20240614123532.203983-1-devarsht@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Certain device-tree node properties of shared device-tree nodes are
different between the AM62P and J722S SoCs. To avoid overriding the
properties and to avoid redefining the nodes in the k3-{soc}-main.dtsi
having such SoC specific properties, move the properties to the SoC
specific k3-{soc}-main.dtsi files.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Acked-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240615081600.3602462-9-s-vadapalli@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Enable PCIe0 instance of PCIe in Root Complex mode of operation with Lane 0
of the SERDES1 instance of SERDES. Also enable USB0 instance of USB to
interface with the Type-C port via the USB hub, by configuring the pin P05
of the GPIO expander on the EVM. Enable USB1 instance of USB in SuperSpeed
mode of operation with Lane 0 of the SERDES0 instance of SERDES.
Co-developed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Acked-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240615081600.3602462-8-s-vadapalli@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
J722S SoC has two instances of SERDES namely SERDES0 and SERDES1 and one
instance of PCIe namely PCIe0. Both SERDES0 and SERDES1 are single lane
SERDES. The PCIe0 instance of PCIe is a Gen3 single lane PCIe controller.
Since SERDES and PCIe are not present on AM62P SoC, add the device-tree
nodes corresponding to them in the J722S SoC specific "k3-j722s-main.dtsi"
file.
Co-developed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Acked-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240615081600.3602462-7-s-vadapalli@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The SERDES0 and SERDES1 instances of SERDES on J722S are single lane
SERDES which are individually muxed across different peripherals.
LANE0 of SERDES0 is muxed between USB and CPSW while LANE0 of SERDES1 is
muxed between PCIe and CPSW.
Define the lane-muxing macros to be used as the idle state values.
Co-developed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240615081600.3602462-6-s-vadapalli@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Update "k3-j722s.dtsi" to include "k3-am62p-j722s-common-{}".dtsi files in
order to reuse the nodes shared with AM62P. Also include the J722S specific
"k3-j722s-main.dtsi".
Since the J7 family of SoCs has the k3-{soc}.dtsi file organized as:
k3-{soc}.dtsi = CPU + Cache + CBASS-Ranges + "Peripheral-Includes"
switch the "k3-j722s.dtsi" file to the same convention.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Acked-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240615081600.3602462-5-s-vadapalli@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Introduce the "k3-j722s-main.dtsi" file to contain main domain peripherals
that are specific to J722S SoC and are not shared with AM62P. The USB1
instance of the USB controller on J722S is different from that on AM62P.
Thus, add the USB1 node in "k3-j722s-main.dtsi".
Co-developed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Acked-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240615081600.3602462-4-s-vadapalli@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The USB1 instance of USB controller on AM62P is different from the USB1
instance of USB controller on J722S. Thus, move the USB1 instance from
the shared "k3-am62p-j722s-common-main.dtsi" file to the AM62p specific
"k3-am62p-main.dtsi" file. Include "k3-am62p-main.dtsi" in "k3-am62p.dtsi".
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Acked-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240615081600.3602462-3-s-vadapalli@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The AM62P and J722S SoCs share most of the peripherals. With the aim of
reusing the existing k3-am62p-{mcu,main,thermal,wakeup}.dtsi files for
J722S SoC, rename them to indicate that they are shared with the J722S SoC.
The peripherals that are not shared will be moved in the upcoming patches
to the respective k3-{soc}-{mcu,main,wakeup}.dtsi files without "common" in
the filename, emphasizing that they are not shared.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Acked-by: Andrew Davis <afd@ti.com>
Acked-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240615081600.3602462-2-s-vadapalli@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The NAND expansion card plugs in over the HSE (High Speed Expansion)
connector. Add support for it.
We add the ranges property to the GPMC node instead of the NAND
overlay file to prevent below warnings.
/fragment@3/__overlay__: Relying on default #address-cells value
/fragment@3/__overlay__: Relying on default #size-cells value
As GPMC is dedicated for NAND use on this board, it should be OK.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240614-am642-evm-nand-v5-1-acf760896239@kernel.org
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add an overlay to disable the spi nor for all am6xx-phycore-som
boards.
The EEPROM on am6xx-phycore-soms contains information about the
configuration of the SOM. The standard configuration of the SOM
has an ospi nor, but if no nor is populated, the EEPROM will indicate
that change and we can use this overlay to cleanly disable the
spi nor.
Signed-off-by: Nathan Morrisson <nmorrisson@phytec.com>
Link: https://lore.kernel.org/r/20240613230759.1984966-5-nmorrisson@phytec.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add an overlay to disable the rtc for all am6xx-phycore-som boards.
The EEPROM on am6xx-phycore-soms contains information about the
configuration of the SOM. The standard configuration of the SOM
has an rtc, but if no rtc is populated, the EEPROM will indicate that
change and we can use this overlay to cleanly disable the rtc.
Signed-off-by: Nathan Morrisson <nmorrisson@phytec.com>
Link: https://lore.kernel.org/r/20240613230759.1984966-4-nmorrisson@phytec.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add an overlay to disable the eth phy for all am6xx-phycore-som
boards.
The EEPROM on am6xx-phycore-soms contains information about the
configuration of the SOM. The standard configuration of the SOM
has an ethernet phy, but if no ethernet phy is populated, the EEPROM
will indicate that change and we can use this overlay to cleanly
disable the ethernet phy.
Signed-off-by: Nathan Morrisson <nmorrisson@phytec.com>
Link: https://lore.kernel.org/r/20240613230759.1984966-3-nmorrisson@phytec.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Label the spi nor as serial_flash. This allows us to disable the
flash with an overlay common to all am6xx-phycore-som boards.
Signed-off-by: Nathan Morrisson <nmorrisson@phytec.com>
Link: https://lore.kernel.org/r/20240613230759.1984966-2-nmorrisson@phytec.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
J721E common processor board can be interfaced with the infotainment
expansion board[0] to enable the following audio/video interfaces in
addition to the peripherals provided by the common processor board:
- Two Audio codecs each with three Stereo Inputs and four Stereo Outputs
- Audio input over FPD Link III
- Digital Audio Interface TX/RX
- HDMI/FPD LINK III Display out
- LI/OV Camera input
Add support for TFP410 HDMI bridge located on the Infotainment Expansion
Board (connected to J46 & J51).
Add a HDMI connector node and connect the endpoints as below:
DSS => TFP410 bridge => HDMI connector
Also add the pinmux data and board muxes for DPI.
Rest of the peripherals are not added as of now.
[0]: <https://www.ti.com/lit/ug/spruit0a/spruit0a.pdf>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
[j-choudhary@ti.com: minor cleanup]
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Reviewed-by: Aradhya Bhatia <a-bhatia1@ti.com>
Link: https://lore.kernel.org/r/20240613093706.480700-1-j-choudhary@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add an overlay to enable PCIe on the am642-phyboard-electra. The
serdes is muxed from USB to PCIe, so we are restricted to USB2 while
using this overlay.
Signed-off-by: Nathan Morrisson <nmorrisson@phytec.com>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20240613195012.1925920-3-nmorrisson@phytec.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Remove pinmuxing for PCIe so that we can add it in an overlay.
Signed-off-by: Nathan Morrisson <nmorrisson@phytec.com>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20240613195012.1925920-2-nmorrisson@phytec.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add the interrupts needed for PTP Hardware Clock support via IEP
in SR1.0 devices.
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Diogo Ivo <diogo.ivo@siemens.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AM69-SK board has 3 instances of PCIe namely PCIe0, PCIe1 and PCIe3.
The x4 PCIe0 instance is connected to a Card Edge connector via SERDES1.
The x2 PCIe1 instance is connected to an M.2 M Key connector via SERDES0.
The x1 PCIe3 instance is connected to an M.2 E Key connector via SERDES0.
Add device-tree support for enabling all 3 PCIe instances in Root-Complex
mode of operation.
Signed-off-by: Dasnavis Sabiya <sabiya.d@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://lore.kernel.org/r/20240529082259.1619695-5-s-vadapalli@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add overlay to enable the PCIe0 and PCIe1 instances of PCIe on J784S4-EVM
in Endpoint mode of operation.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://lore.kernel.org/r/20240529082259.1619695-4-s-vadapalli@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Enable PCIe0 and PCIe1 instances of PCIe in Root Complex mode of
operation on J784S4 EVM. The lanes of PCIe0 are connected to Serdes1
instance of Serdes while the lanes of PCIe1 are connected to Serdes0
instance of Serdes in J784S4 SoC. Despite both PCIe instances supporting
up to 4 Lanes, since the physical connections to the PCIe connector
corresponding to the PCIe1 instance of PCIe are limited to 2 Lanes on
the J784S4 EVM, update the "num-lanes" property of PCIe1 accordingly.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://lore.kernel.org/r/20240529082259.1619695-3-s-vadapalli@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
TI's J784S4 SoC has four instances of Gen3 PCIe Controllers namely
PCIe0, PCIe1, PCIe2 and PCIe3. PCIe0 and PCIe1 are 4-Lane controllers
while PCIe2 and PCIe3 are 2-Lane controllers.
Add support for the Root Complex Mode of operation of these PCIe instances.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://lore.kernel.org/r/20240529082259.1619695-2-s-vadapalli@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add the "ethernet-mac-syscon" node within "wkup_conf" node corresponding to
the CTRLMMR_MAC_IDx registers within the CTRL_MMR space. Assign the
compatible "ti,am62p-cpsw-mac-efuse" to enable "syscon_regmap" operations
on these registers. The MAC Address programmed in the eFuse is accessible
through the CTRLMMR_MAC_IDx registers. The "ti,syscon-efuse" device-tree
property points to the CTRLMMR_MAC_IDx registers, allowing the CPSW driver
to fetch the MAC Address and assign it to the network interface associated
with CPSW3G MAC Port 1.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240604104425.3770037-1-s-vadapalli@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The am625 is capable of running at 1.4 GHz when VDD_CORE is increased
from 0.75V to 0.85V. Increasing the voltage while the AM625 is
running has not been validated by TI, so we provide an overlay so that
people may choose to run at 1.4 GHz if they need the additional
performance.
Signed-off-by: Nathan Morrisson <nmorrisson@phytec.com>
Link: https://lore.kernel.org/r/20240425221925.1781226-1-nmorrisson@phytec.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
On SK-AM62P, McASP1 uses two pins for communicating with the codec over
I2S protocol. One of these pins (AXR0) is used for audio playback (TX)
so the direction of the pin should be OUTPUT.
Fixes: c00504ea42 ("arm64: dts: ti: k3-am62p5-sk: Updates for SK EVM")
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240606-mcasp_fifo_drop-v2-7-8c317dabdd0a@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
McASP AFIFOs are not necessary with UDMA-P/BCDMA as there is buffering
on the DMA IP. Drop these for better audio latency.
Fixes: 28c0cf16b3 ("arm64: dts: ti: k3-am625-phyboard-lyra-rdk: Add Audio Codec")
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240606-mcasp_fifo_drop-v2-6-8c317dabdd0a@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
McASP AFIFOs are not necessary with UDMA-P/BCDMA as there is buffering
on the DMA IP. Drop these for better audio latency.
Fixes: 316b80246b ("arm64: dts: ti: add verdin am62")
Acked-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240606-mcasp_fifo_drop-v2-5-8c317dabdd0a@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
McASP AFIFOs are not necessary with UDMA-P/BCDMA as there is buffering
on the DMA IP. Drop these for better audio latency.
Fixes: 1f7226a5e5 ("arm64: dts: ti: k3-am625-beagleplay: Add HDMI support")
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240606-mcasp_fifo_drop-v2-4-8c317dabdd0a@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
McASP AFIFOs are not necessary with UDMA-P/BCDMA as there is buffering
on the DMA IP. Drop these for better audio latency.
Fixes: c00504ea42 ("arm64: dts: ti: k3-am62p5-sk: Updates for SK EVM")
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240606-mcasp_fifo_drop-v2-3-8c317dabdd0a@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
McASP AFIFOs are not necessary with UDMA-P/BCDMA as there is buffering
on the DMA IP. Drop these for better audio latency.
Fixes: 4a2c5dddf9 ("arm64: dts: ti: k3-am62a7-sk: Enable audio on AM62A")
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240606-mcasp_fifo_drop-v2-2-8c317dabdd0a@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
McASP AFIFOs are not necessary with UDMA-P/BCDMA as there is buffering
on the DMA IP. Drop these for better audio latency.
Fixes: b94b43715e ("arm64: dts: ti: Enable audio on SK-AM62(-LP)")
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240606-mcasp_fifo_drop-v2-1-8c317dabdd0a@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add device tree overlay to enable both ICSSG1 ports available on AM64x-EVM
in MII mode.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Link: https://lore.kernel.org/r/20240429092919.657629-1-danishanwar@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
A PRU system event "vring" has been added to each PRU and RTU
node in each of the ICSSG0, ICSSG1 and ICSSG2 remote processor
subsystems to enable the virtio/rpmsg communication between MPU
and that PRU/RTU core. The additions are done in the base
k3-am65-main.dtsi, and so are inherited by all the K3 AM65x
boards.
The PRU system events is the preferred approach over using TI
mailboxes, as it eliminates an external peripheral access from
the PRU/RTU-side, and keeps the interrupt generation internal to
the ICSSG. The difference from MPU would be minimal in using one
versus the other.
Mailboxes can still be used if desired, but currently there is
no support on firmware-side for K3 SoCs to use mailboxes. Either
approach would require that an appropriate firmware image is
loaded/booted on the PRU.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Link: https://lore.kernel.org/r/20240529064420.571615-3-danishanwar@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
PRU system events "vring" have been added to each PRU and RTU node
in each of the ICSSG0 and ICSSG1 remote processor subsystems to
enable the virtio/rpmsg communication between MPU and that PRU/RTU core.
No events have been added to the Tx_PRU cores at present. The
additions are done in the base k3-am64main.dtsi, and so are inherited
by all the K3 AM64x boards.
The PRU system events is the preferred approach over using TI
mailboxes, as it eliminates an external peripheral access from
the PRU/RTU-side, and keeps the interrupt generation internal to
the ICSSG. The difference from MPU would be minimal in using one
versus the other.
Mailboxes can still be used if desired, but currently there is
no support on firmware-side for K3 SoCs to use mailboxes. Either
approach would require that an appropriate firmware image is
loaded/booted on the PRU.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Link: https://lore.kernel.org/r/20240529064420.571615-2-danishanwar@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add Tulip TPS62873 nodes for J784S4 EVM. These are step-down regulators
that supply VDD_CPU_AVS and VDD_CORE_0V8 to the SoC.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Link: https://lore.kernel.org/r/20240528040159.3919652-4-n-francis@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add DTS node for two TPS6287x high current buck convertors.
The two TPS6287x supply power to the MAIN domain for AVS and other core
supplies.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Link: https://lore.kernel.org/r/20240528040159.3919652-3-n-francis@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add DTS node for LP87334E PMIC and two TPS6287x high current buck
converters.
LP87334E is responsible for supplying power to the MCU and MAIN domains
as well as to LPDDR4. The two TPS6287x supply power to the MAIN
domain for AVS and other core supplies.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Link: https://www.ti.com/lit/pdf/slda060
Link: https://lore.kernel.org/r/20240528040159.3919652-2-n-francis@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The board uses SERDES0 Lane 3 for USB3 IP. So update the
SerDes lane info for USB. Add the pin mux data and
enable USB3 support.
Signed-off-by: Matt Ranostay <mranostay@ti.com>
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # k3-j784s4-evm
Link: https://lore.kernel.org/r/20240507095545.8210-3-r-gunasekaran@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add support for the USB 3.0 controller
Signed-off-by: Matt Ranostay <mranostay@ti.com>
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # k3-j784s4-evm
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240507095545.8210-2-r-gunasekaran@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
CAN instances 0 and 1 in the mcu domain and 16 in the main domain are
brought on the evm through headers J42, J43 and J46 respectively. Thus,
add their respective transceiver's 0, 1 and 2 dt nodes to add support
for these CAN instances.
CAN instance 4 in the main domain is brought on the evm through header
J45. The CAN High and Low lines from the SoC are routed through a mux
on the evm. The select lines need to be set for the CAN signals to
reach to its transceiver on the evm. Therefore, add transceiver 3
dt node to add support for this CAN instance.
Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com>
Link: https://lore.kernel.org/r/20240411201747.18697-1-b-kapoor@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
On-chip RTC is used as a wakeup source on am62a board designs. This
patch removes the disabled status property to enable the RTC node.
Signed-off-by: Vibhore Vardhan <vibhore@ti.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20240429184445.14876-1-vibhore@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
CAN instance 0 in the mcu domain is brought on the J721E-SK board
through header J1. Thus, add its respective transceiver 1 dt node to add
support for this CAN instance.
CAN instances 0, 5 and 9 in the main domain are brought on the J721E-SK
board through headers J5, J6 and J2 respectively. Thus, add their
respective transceivers 2, 3 and 4 dt nodes to add support for these CAN
instances.
Signed-off-by: Beleswar Padhi <b-padhi@ti.com>
Reviewed-by: Bhavya Kapoor <b-kapoor@ti.com>
Link: https://lore.kernel.org/r/20240430131512.1327283-1-b-padhi@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
J722S does not pin out all of the GPIO same as AM62P and have
more number of GPIO on the main_gpio1 instance. Fix the GPIO
count on both instances by overriding the ti,ngpio property.
Fixes: ea55b9335a ("arm64: dts: ti: Introduce J722S family of SoCs")
More details at J722S/AM67 Datasheet (Section 5.3.11, GPIO):
https://www.ti.com/lit/ds/symlink/am67.pdf
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Link: https://lore.kernel.org/r/20240507103332.167928-1-vaishnav.a@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add the bootph-all property to the memory node so that it can be
accessed by FDT functions at bootloader stage.
The bootloader requires the memory node to be able to initialize and set
the size of the DRAM banks. For this purpose, make sure all memory nodes
are present and standardized, and modify them if not.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Link: https://lore.kernel.org/r/20240506110203.3230255-1-n-francis@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The RS485 transceiver RE (Receiver enable) and DE (Driver enable) are
shorted and connected to both RTS/CTS of the SoC UART.
RE is active-low, DE is active-high.
Remove the "rs485-rts-active-low" flag to match RTS polarity with DE,
and fix communication in both transmit and receive directions.
Fixes: d60483faf9 ("arm64: dts: add description for solidrun am642 som and evaluation board")
Signed-off-by: Josua Mayer <josua@solid-run.com>
Link: https://lore.kernel.org/r/20240504-ti-rs485-rts-v1-1-e88ef1c96f34@solid-run.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
For main_pktdma node, the TX Channel Realtime Register region 'tchanrt'
is 128KB and Ring Realtime Register region 'ringrt' is 2MB as shown in
memory map in the TRM[0] (Table 2-1).
So fix ranges for those register regions.
[0]: <https://www.ti.com/lit/pdf/spruj83>
Fixes: b5080c7c1f ("arm64: dts: ti: k3-am62p: Add nodes for more IPs")
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20240430105253.203750-4-j-choudhary@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
For main_pktdma node, the TX Channel Realtime Register region 'tchanrt'
is 128KB and Ring Realtime Register region 'ringrt' is 2MB as shown in
memory map in the TRM[0] (Table 2-1).
So fix ranges for those register regions.
[0]: <https://www.ti.com/lit/pdf/spruj16>
Fixes: 3dad70def7 ("arm64: dts: ti: k3-am62a-main: Add more peripheral nodes")
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20240430105253.203750-3-j-choudhary@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
For main_pktdma node, the TX Channel Realtime Register region 'tchanrt'
is 128KB and Ring Realtime Register region 'ringrt' is 2MB as shown in
memory map in the TRM[0] (Table 2-1).
So fix ranges for those register regions.
[0]: <https://www.ti.com/lit/pdf/spruiv7>
Fixes: c37c58fdeb ("arm64: dts: ti: k3-am62: Add more peripheral nodes")
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20240430105253.203750-2-j-choudhary@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The CPSW9G instance of the CPSW Ethernet Switch supports USXGMII mode
with MAC Ports 1 and 2 of the instance, which are connected to ENET
Expansion 1 and ENET Expansion 2 slots on the EVM respectively, through
the Serdes2 instance of the SERDES.
Enable CPSW9G MAC Ports 1 and 2 in fixed-link configuration USXGMII mode
at 5 Gbps each.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Chintan Vankar <c-vankar@ti.com>
Link: https://lore.kernel.org/r/20240502091002.3659435-6-c-vankar@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The J7 Quad Port Add-On Ethernet Card for J784S4 EVM supports
QSGMII mode. Use the overlay to configure CPSW9G ports in QSGMII
mode with the Add-On Ethernet Card connected to the ENET Expansion
1 slot on the EVM.
Add support to reset the PHY from kernel by using gpio-hog and
gpio-reset.
Add aliases for CPSW9G ports to enable kernel to fetch MAC Addresses
directly from U-Boot.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Chintan Vankar <c-vankar@ti.com>
Link: https://lore.kernel.org/r/20240502091002.3659435-5-c-vankar@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Enable MAIN CPSW2G and add alias for it to enable Linux to fetch
MAC Address for the port directly from U-Boot.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Signed-off-by: Chintan Vankar <c-vankar@ti.com>
Link: https://lore.kernel.org/r/20240502091002.3659435-4-c-vankar@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
J784S4 SoC has MAIN CPSW2G and CPSW9G instances of the CPSW
Ethernet Switch. CPSW2G has 1 external port and 1 host port
while CPSW9G has 8 external ports and 1 host port.
Add device-tree nodes for MAIN CPSW2G and CPSW9G and disable
them by default. MAIN CPSW2G will be enabled in the board file
while device-tree overlays will be used to enable CPSW9G.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Chintan Vankar <c-vankar@ti.com>
Link: https://lore.kernel.org/r/20240502091002.3659435-3-c-vankar@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add alias for the MCU CPSW2G port to enable Linux to fetch MAC Address
for the port directly from U-Boot.
Signed-off-by: Chintan Vankar <c-vankar@ti.com>
Link: https://lore.kernel.org/r/20240502091002.3659435-2-c-vankar@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Fix the output filenames of the combined device tree blobs generated by
applying *-csi2-dual-imx219-* overlays on the base dtbs during compile
test.
Fixes: f767eb9180 ("arm64: dts: ti: k3-j721e-sk: Add overlay for IMX219")
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Reviewed-by: Aradhya Bhatia <a-bhatia1@ti.com>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Link: https://lore.kernel.org/r/104fbdbc-a3f6-091a-72f4-17d4fa24ad92@ti.com/
Signed-off-by: Nishanth Menon <nm@ti.com>
The RESET GPIO pinmux should be part of MDIO bus node
so that they can be in the right state before the PHY
can be probed via MDIO bus scan.
The GPIO pin should be setup with PIN_INPUT so that
input circuitry is enabled in case software wants to
check pin status. Without this, incorrect status is shown
in /sys/kernel/debug/gpio.
Add GPIO reset for the Gigabit Ethernet PHY. As per
RTL8211F datasheet, reset assert width is 10ms and
PHY registers can be access accessed after 50ms of
reset deassert.
Fixes: f5a731f078 ("arm64: dts: ti: Add k3-am625-beagleplay")
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240305-b4-for-v6-9-am65-beagleplay-ethernet-reset-v2-1-2bf463a7bf13@kernel.org
Signed-off-by: Nishanth Menon <nm@ti.com>
The USB-C PD manages plug orientation, power delivery, and our endpoint
for the USB interface. Add this node and include its endpoint.
Configure USB0 for role-switching and wire it to our USB-C PD endpoint.
Signed-off-by: Garrett Giordano <ggiordano@phytec.com>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20240425152558.485763-1-ggiordano@phytec.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Previously, we had the sleep-moci pin set to always on. However, the
Dahlia carrier board supports disabling the sleep-moci when the system
is suspended to power down peripherals that support it. This reduces
overall power consumption. This commit adds support for this feature by
disabling the reg_force_sleep_moci regulator and adding a new regulator
for the USB hub that can be turned off when the system is suspended.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://lore.kernel.org/r/20240301084901.16656-3-eichest@gmail.com
Signed-off-by: Nishanth Menon <nm@ti.com>
The Verdin family has a signal called sleep-moci which can be used to
turn off peripherals on the carrier board when the SoM goes into
suspend. So far we have hogged this signal, which means the peripherals
are always on and it is not possible to add peripherals that depend on
the sleep-moci to be on. With this change, we replace the hog with a
regulator so that peripherals can add their own regulators that use the
same gpio. Carrier boards that allow peripherals to be powered off in
suspend can disable this regulator and implement their own regulator to
control the sleep-moci.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://lore.kernel.org/r/20240301084901.16656-2-eichest@gmail.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Remove sdhci-caps-mask to enable support for SDR104 speed mode for
SD card and remove no-1-8-v property so that SD card can work in
any UHS-1 high speed mode it can support.
Fixes: 4664ebd834 ("arm64: dts: ti: Add initial support for J784S4 SoC")
Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com>
Signed-off-by: Dasnavis Sabiya <sabiya.d@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Judith Mendez <jm@ti.com>
Link: https://lore.kernel.org/r/20240423151732.3541894-6-jm@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
According to TRM for J721S2, SDR104 speed mode is supported by the SoC
but its capabilities were masked in device tree. Remove sdhci-caps-mask
to enable support for SDR104 speed mode for SD card in J721S2 SoC.
[+] Refer to : section 12.3.6.1.1 MMCSD Features, in J721S2 TRM
- https://www.ti.com/lit/zip/spruj28
Fixes: b8545f9d3a ("arm64: dts: ti: Add initial support for J721S2 SoC")
Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20240423151732.3541894-5-jm@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Hook up required IO voltage regulators and drop no-1-8-v to support UHS
modes on SD cards.
Fixes: 5fc6b1b626 ("arm64: dts: ti: Introduce AM62A7 family of SoCs")
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Judith Mendez <jm@ti.com>
Link: https://lore.kernel.org/r/20240423151732.3541894-4-jm@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
On AM65x platform, sdhci0 is for eMMC and sdhci1 is for SD.
Remove the properties that are not applicable for each device.
Fixes: eac99d38f8 ("arm64: dts: ti: k3-am654-main: Update otap-del-sel values")
Fixes: d7600d070f ("arm64: dts: ti: k3-am65-main: Add support for sdhci1")
Signed-off-by: Judith Mendez <jm@ti.com>
Link: https://lore.kernel.org/r/20240423151732.3541894-3-jm@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Update otap-del-sel properties as per datasheet [0].
Add missing clkbuf-sel and itap-del-sel values also as per
datasheet [0].
Move clkbuf-sel and ti,trm-icp above the otap-del-sel properties
so the sdhci nodes could be more uniform across platforms.
[0] https://www.ti.com/lit/ds/symlink/am6548.pdf
Fixes: eac99d38f8 ("arm64: dts: ti: k3-am654-main: Update otap-del-sel values")
Fixes: d7600d070f ("arm64: dts: ti: k3-am65-main: Add support for sdhci1")
Signed-off-by: Judith Mendez <jm@ti.com>
Link: https://lore.kernel.org/r/20240423151732.3541894-2-jm@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Add symbols when building the am625-phyboard-lyra-rdk DTB so
overlays can be applied.
Fixes: d8280f30a9 ("arm64: dts: ti: am62-phyboard-lyra: Add overlay to enable a GPIO fan")
Signed-off-by: Nathan Morrisson <nmorrisson@phytec.com>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20240419193552.3090343-1-nmorrisson@phytec.com
Signed-off-by: Nishanth Menon <nm@ti.com>
The phyBOARD-Electra has a GPIO fan header. This overlay enables the fan
header and sets the fan to turn on at 65C.
Signed-off-by: Nathan Morrisson <nmorrisson@phytec.com>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20240419193114.3090084-1-nmorrisson@phytec.com
Signed-off-by: Nishanth Menon <nm@ti.com>
This patch adds support for the Wave521cl on the AM62A-SK.
Signed-off-by: Brandon Brnich <b-brnich@ti.com>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Link: https://lore.kernel.org/r/20240415204659.798548-1-b-brnich@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
As per AM62A TRM [1] USB Link Power Management (LPM)
feature is not supported. Disable it else it may
cause enumeration failure on some devices.
> 4.9.2.1 USB2SS Unsupported Features
> The following features are not supported on this family of devices:
> ...
> - USB 2.0 ECN: Link Power Management (LPM)
> ...
[1] - https://www.ti.com/lit/pdf/spruj16
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Link: https://lore.kernel.org/r/20240412-for-v6-10-am62-usb-typec-dt-v7-3-93b827adf97e@kernel.org
Signed-off-by: Nishanth Menon <nm@ti.com>
There are two USB instances available on the am62p5 starter kit. Include
and enable them for use on the board.
USB LPM feature is kept disabled as it is not supported.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240412-for-v6-10-am62-usb-typec-dt-v7-2-93b827adf97e@kernel.org
Signed-off-by: Nishanth Menon <nm@ti.com>
Exposing the entire CTRL_MMR space to syscon is not a good idea.
Add sub-nodes for USB0_PHY_CTRL and USB1_PHY_CTRL and use them
in the USB0/USB1 nodes.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240412-for-v6-10-am62-usb-typec-dt-v7-1-93b827adf97e@kernel.org
Signed-off-by: Nishanth Menon <nm@ti.com>
Add the required nodes to enable ICSSG SR1.0 based prueth networking.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Diogo Ivo <diogo.ivo@siemens.com>
Link: https://lore.kernel.org/r/20240409164314.157602-1-diogo.ivo@siemens.com
Signed-off-by: Nishanth Menon <nm@ti.com>
The Audio Codec runs over the MCASP (Multichannel Audio Serial Port).
Add pinmux for the Audio Reference Clock and MCASP2.
Add DT nodes for Audio Codec, MCASP2, VCC 1v8 and VCC 3v3 regulators.
Additionally, create a sound node that connects our sound card and the
MCASP2.
Signed-off-by: Garrett Giordano <ggiordano@phytec.com>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20240404184250.3772829-1-ggiordano@phytec.com
Signed-off-by: Nishanth Menon <nm@ti.com>
The FSS bus contains several register ranges. Using an empty
ranges property works but causes a DT warning when we give
this node an address. Fix this by explicitly defining the
memory ranges in use.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240326205920.40147-4-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
The FSS bus contains several register ranges. Using an empty
ranges property works but causes a DT warning when we give
this node an address. Fix this by explicitly defining the
memory ranges in use.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240326205920.40147-3-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
The FSS bus contains several register ranges. Using an empty
ranges property works but causes a DT warning when we give
this node an address. Fix this by explicitly defining the
memory ranges in use.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240326205920.40147-2-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
The FSS bus contains several register ranges. Using an empty
ranges property works but causes a DT warning when we give
this node an address. Fix this by explicitly defining the
memory ranges in use.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240326205920.40147-1-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
These SerDes lane select muxes use bits from the same register as
the SerDes clock select mux. Make the lane select mux a child
of the SerDes control node.
This removes one more requirement on scm-conf being a syscon node
which will later be converted to fix a couple DTS check warnings.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240326185627.29852-2-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
This matches the binding for this register region which fixes a couple
DTS check warnings.
While here trim the leading 0s from the "reg" definition.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240326185627.29852-1-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
The J722S EVM has an on-board eMMC. Enable the SDHC interface for it.
There is no pinmuxing required because the interface has dedicated pins.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Link: https://lore.kernel.org/r/20240403102302.3934932-1-mwalle@kernel.org
Signed-off-by: Nishanth Menon <nm@ti.com>
Device tree best practice is to disable any external interface in the
dtsi and just enable them if needed in the device tree. Thus, disable
the ethernet switch and its ports by default and just enable the ones
used by the EVMs in their device trees.
There is no functional change.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Acked-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240403101545.3932437-1-mwalle@kernel.org
Signed-off-by: Nishanth Menon <nm@ti.com>
The phyBOARD-Electra has two TCAN1044VDD CAN transceivers which
support CAN FD at 8 Mbps.
Increase the maximum bitrate to 8 Mbps.
Signed-off-by: Nathan Morrisson <nmorrisson@phytec.com>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20240402160825.1516036-3-nmorrisson@phytec.com
Signed-off-by: Nishanth Menon <nm@ti.com>
The phyBOARD-Lyra has one TCAN1044VDD CAN transceiver which supports
CAN FD at 8 Mbps.
Increase the maximum bitrate to 8 Mbps.
Signed-off-by: Nathan Morrisson <nmorrisson@phytec.com>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20240402160825.1516036-2-nmorrisson@phytec.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Add a GPIO hog to release PCIe reset on the carrier board, this is
required to use M.2 or mPCIe cards.
Verdin AM62 does not have any PCIe interface, however the Verdin family
has PCIe and normally an M.2 or mPCIe slot is available in the carrier
board that can be used with cards that use only the USB interface toward
the host CPU, for example cellular network modem.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://lore.kernel.org/r/20240327182801.5997-3-francesco@dolcini.it
Signed-off-by: Nishanth Menon <nm@ti.com>
Generic GPIOs pinctrl nodes are not correct, gpio[1-4] are into the MCU
domain and should be into &mcu_gpio0, gpio[5-8] were missing and are added
in this commit.
Fixes: 7698622fbc ("arm64: dts: ti: Add verdin am62 mallow board")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://lore.kernel.org/r/20240327182801.5997-2-francesco@dolcini.it
Signed-off-by: Nishanth Menon <nm@ti.com>
As described in the binding document for the "current-speed" property:
"This should only be present in case a driver has no chance to know the
baud rate of the slave device."
This is not the case for the UART used in K3 devices, the current
baud-rate can be calculated from the registers. Having this property
has the effect of actually skipping the baud-rate setup in some drivers
as it assumes it will already be set to this rate, which may not always
be the case.
It seems this property's purpose was mistaken as selecting the desired
baud-rate, which it does not. It would have been wrong to select that
here anyway as DT is not the place for configuration, especially when
there are already more standard ways to set serial baud-rates.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240326185441.29656-6-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
As described in the binding document for the "current-speed" property:
"This should only be present in case a driver has no chance to know the
baud rate of the slave device."
This is not the case for the UART used in K3 devices, the current
baud-rate can be calculated from the registers. Having this property
has the effect of actually skipping the baud-rate setup in some drivers
as it assumes it will already be set to this rate, which may not always
be the case.
It seems this property's purpose was mistaken as selecting the desired
baud-rate, which it does not. It would have been wrong to select that
here anyway as DT is not the place for configuration, especially when
there are already more standard ways to set serial baud-rates.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240326185441.29656-5-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
As described in the binding document for the "current-speed" property:
"This should only be present in case a driver has no chance to know the
baud rate of the slave device."
This is not the case for the UART used in K3 devices, the current
baud-rate can be calculated from the registers. Having this property
has the effect of actually skipping the baud-rate setup in some drivers
as it assumes it will already be set to this rate, which may not always
be the case.
It seems this property's purpose was mistaken as selecting the desired
baud-rate, which it does not. It would have been wrong to select that
here anyway as DT is not the place for configuration, especially when
there are already more standard ways to set serial baud-rates.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240326185441.29656-4-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
As described in the binding document for the "current-speed" property:
"This should only be present in case a driver has no chance to know the
baud rate of the slave device."
This is not the case for the UART used in K3 devices, the current
baud-rate can be calculated from the registers. Having this property
has the effect of actually skipping the baud-rate setup in some drivers
as it assumes it will already be set to this rate, which may not always
be the case.
It seems this property's purpose was mistaken as selecting the desired
baud-rate, which it does not. It would have been wrong to select that
here anyway as DT is not the place for configuration, especially when
there are already more standard ways to set serial baud-rates.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240326185441.29656-3-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
As described in the binding document for the "current-speed" property:
"This should only be present in case a driver has no chance to know the
baud rate of the slave device."
This is not the case for the UART used in K3 devices, the current
baud-rate can be calculated from the registers. Having this property
has the effect of actually skipping the baud-rate setup in some drivers
as it assumes it will already be set to this rate, which may not always
be the case.
It seems this property's purpose was mistaken as selecting the desired
baud-rate, which it does not. It would have been wrong to select that
here anyway as DT is not the place for configuration, especially when
there are already more standard ways to set serial baud-rates.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240326185441.29656-2-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
As described in the binding document for the "current-speed" property:
"This should only be present in case a driver has no chance to know the
baud rate of the slave device."
This is not the case for the UART used in K3 devices, the current
baud-rate can be calculated from the registers. Having this property
has the effect of actually skipping the baud-rate setup in some drivers
as it assumes it will already be set to this rate, which may not always
be the case.
It seems this property's purpose was mistaken as selecting the desired
baud-rate, which it does not. It would have been wrong to select that
here anyway as DT is not the place for configuration, especially when
there are already more standard ways to set serial baud-rates.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240326185441.29656-1-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
On am62-lp-sk the PMIC is not wired up to a power button. Remove this
property. This fixes issues observed when entering a very deep sleep
state that is not yet available upstream.
Fixes: e6a51ffabf ("arm64: ti: dts: Add support for AM62x LP SK")
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://lore.kernel.org/r/20240325152029.2933445-1-msp@baylibre.com
Signed-off-by: Nishanth Menon <nm@ti.com>
BeaglePlay SBC[1] has Texas Instrument's WL18xx WiFi chipset[2].
Currently, WLAN_EN is configured as regulator and regulator-always-on.
However, the timing and wlan_en sequencing is not correctly modelled.
This causes the sdio access to fail during runtime-pm power operations
saving or during system suspend/resume/hibernation/freeze operations.
This is because the WLAN_EN line is not deasserted to low '0' to power
down the WiFi. So during restore, the WiFi driver tries to load the FW
without following correct power sequence. WLAN_EN => '1'/assert (high)
to power-up the chipset.
Use mmc-pwrseq-simple to drive TI's WiFi (WL18xx) chipset enable
'WLAN_EN'. mmc-pwrseq-simple provides power sequence flexibility with
support for post power-on and power-off delays.
Typical log signature that indicates this bug is:
wl1271_sdio mmc2:0001:2: sdio write failed (-110)
Followed by possibly a kernel warning (depending on firmware present):
WARNING: CPU: 1 PID: 45 at drivers/net/wireless/ti/wlcore/sdio.c:123 wl12xx_sdio_raw_write+0xe4/0x168 [wlcore_sdio]
[1] https://www.beagleboard.org/boards/beagleplay
[2] https://www.ti.com/lit/ds/symlink/wl1807mod.pdf
Fixes: f5a731f078 ("arm64: dts: ti: Add k3-am625-beagleplay")
Suggested-by: Shengyu Qu <wiagn233@outlook.com>
Signed-off-by: Sukrut Bellary <sukrut.bellary@linux.com>
Tested-by: Robert Nelson <robertcnelson@gmail.com>
Link: https://lore.kernel.org/r/20240325143511.2144768-1-nm@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
TI SDHCI instance has a hardware debounce timer of 1 second as described
in commit 7ca0f166f5 ("mmc: sdhci_am654: Add workaround for card detect
debounce timer"), because of this the boot time increases of up to 1
second.
Workaround the issue the same way that is done on
arch/arm64/boot/dts/ti/k3-am625-beagleplay.dts, using the SD1 CD as
GPIO.
Suggested-by: Nishanth Menon <nm@ti.com>
Reported-by: João Paulo Silva Gonçalves <joao.goncalves@toradex.com>
Closes: https://lore.kernel.org/all/0e81af80de3d55e72f79af83fa5db87f5c9938f8.camel@toradex.com/
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://lore.kernel.org/r/20240325083340.89568-1-francesco@dolcini.it
Signed-off-by: Nishanth Menon <nm@ti.com>
In current configuration, wm8904 codec on Dahlia carrier board provides
distorted audio output. This happens due to reference clock is fixed to
25MHz and no FLL is enabled. During playback following parameters are set:
44100Hz:
[ 310.276924] wm8904 1-001a: Target BCLK is 1411200Hz
[ 310.276990] wm8904 1-001a: Using 25000000Hz MCLK
[ 310.277001] wm8904 1-001a: CLK_SYS is 12500000Hz
[ 310.277018] wm8904 1-001a: Selected CLK_SYS_RATIO of 256
[ 310.277026] wm8904 1-001a: Selected SAMPLE_RATE of 44100Hz
[ 310.277034] wm8904 1-001a: Selected BCLK_DIV of 80 for 1562500Hz BCLK
[ 310.277044] wm8904 1-001a: LRCLK_RATE is 35
Deviation = 1411200 vs 1562500 = 10.721%
Also, LRCLK_RATE is 35, should be 32.
48000Hz:
[ 302.449970] wm8904 1-001a: Target BCLK is 1536000Hz
[ 302.450037] wm8904 1-001a: Using 25000000Hz MCLK
[ 302.450049] wm8904 1-001a: CLK_SYS is 12500000Hz
[ 302.450065] wm8904 1-001a: Selected CLK_SYS_RATIO of 256
[ 302.450074] wm8904 1-001a: Selected SAMPLE_RATE of 48000Hz
[ 302.450083] wm8904 1-001a: Selected BCLK_DIV of 80 for 1562500Hz BCLK
[ 302.450092] wm8904 1-001a: LRCLK_RATE is 32
Deviation = 1536000 vs 1562500 = 1.725%
Enabling wm8904 FLL via providing mclk-fs property to simple-audio-card
configures clocks properly, but also adjusts audio reference clock
(mclk), which in case of TI AM62 should be avoided, as it only
supports 25MHz output [1][2].
This change enables FLL on wm8904 by providing mclk-fs, and drops
audio reference clock out of DAI configuration, which prevents
simple-audio-card to adjust it before every playback [3].
41000Hz:
[ 111.820533] wm8904 1-001a: FLL configured for 25000000Hz->11289600Hz
[ 111.820597] wm8904 1-001a: Clock source is 0 at 11289600Hz
[ 111.820651] wm8904 1-001a: Using 11289600Hz FLL clock
[ 111.820703] wm8904 1-001a: CLK_SYS is 11289600Hz
[ 111.820798] wm8904 1-001a: Target BCLK is 1411200Hz
[ 111.820847] wm8904 1-001a: Using 11289600Hz FLL clock
[ 111.820894] wm8904 1-001a: CLK_SYS is 11289600Hz
[ 111.820933] wm8904 1-001a: Selected CLK_SYS_RATIO of 256
[ 111.820971] wm8904 1-001a: Selected SAMPLE_RATE of 44100Hz
[ 111.821009] wm8904 1-001a: Selected BCLK_DIV of 80 for 1411200Hz BCLK
[ 111.821051] wm8904 1-001a: LRCLK_RATE is 32
48000Hz:
[ 144.119254] wm8904 1-001a: FLL configured for 25000000Hz->12288000Hz
[ 144.119309] wm8904 1-001a: Clock source is 0 at 12288000Hz
[ 144.119364] wm8904 1-001a: Using 12288000Hz FLL clock
[ 144.119413] wm8904 1-001a: CLK_SYS is 12288000Hz
[ 144.119512] wm8904 1-001a: Target BCLK is 1536000Hz
[ 144.119561] wm8904 1-001a: Using 12288000Hz FLL clock
[ 144.119608] wm8904 1-001a: CLK_SYS is 12288000Hz
[ 144.119646] wm8904 1-001a: Selected CLK_SYS_RATIO of 256
[ 144.119685] wm8904 1-001a: Selected SAMPLE_RATE of 48000Hz
[ 144.119723] wm8904 1-001a: Selected BCLK_DIV of 80 for 1536000Hz BCLK
[ 144.119764] wm8904 1-001a: LRCLK_RATE is 32
[1]: https://e2e.ti.com/support/processors-group/processors/f/processors-forum/1175479/processor-sdk-am62x-output-audio_ext_refclk0-as-mclk-for-codec-and-mcbsp/4444986#4444986
[2]: https://e2e.ti.com/support/processors-group/processors/f/processors-forum/1188051/am625-audio_ext_refclk1-clock-output---dts-support/4476322#4476322
[3]: sound/soc/generic/simple-card-utils.c#L441
Fixes: f5bf894c86 ("arm64: dts: ti: verdin-am62: dahlia: add sound card")
Suggested-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://lore.kernel.org/r/20240315102500.18492-1-andrejs.cainikovs@gmail.com
Signed-off-by: Nishanth Menon <nm@ti.com>
New Features across family / New SoCs:
- J722s SoC and board support with OSPI NOR, CPSW ethernet
- Camera capture support on mulitple J7xx SoCs, AM68, AM69 and AM62P SoCs
- Wave5 Encoder/Decoder support for J721s2, J784s4 and AM62P
Generic Cleanups/Fixes:
- Stop spliting single mbox items
- Adds MIT license along with GPL-2.0 for all TI DTS files
- Moves PCIe EP nodes in overlays
- VTM Power domain fixups for J7xx SoCs
- Conversion of mmio mux users to reg-mux where possible
- Drops unnecessary UART pinmuxes on J7xx SoCs
- MMC TAP value updates for AM64/AM62A/AM62P for improved stability
- DSS register space updates for AM65/AM62/AM62A
SoC specific Fixes/Features:
J7200:
- Adds CAN support
- New compatible for J7200 to support IO wakeup
AM62A
- HDMI Display (DSS) support
- Move to simple-bus for main_conf node
- eMMC, additional MMC/SD instance support
AM62
- move to simple-bus for main_conf node
AM654
- IOT2050-SM board support
- IOT2050 DT refractoring.
AM64
- SolidRun AM642 HummingBoard-T support and its DT overlays
- ICSSG Ethernet support and associated peripherals
Board specific fixes/Features:
- Beagle Play MDIO and USB node fixes
- TPM support on k3-am642-phyboard-electra and verdin-am62-mallow
- Phycore-am64 ADC
- PCIe + USB2.0 SERDES and PCIe + USB3.0 SERDES card support
- USB1 support on verdin-am62
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEEyRC2zAhGcGjrhiNExEYeRXyRFuMFAmXdqWMQHHZpZ25lc2hy
QHRpLmNvbQAKCRDERh5FfJEW425kB/4spafS0XBafSITRuMy4qcIpXtoEUJoGky3
yQje7rZoM6QX2xuISUv+AydIn5JO2U/ar7UVGwY8qsKB/frq+RjvHlZLGNUynwTR
viAai3aRQv+olhUlZByWS7R8rax5f7H4dPh2a1im4bg1Ljxv1Az7NTRAFh8XzF+e
bMJgNI1Y0iCog9uf1gLig/tXAKBo4SZruE+UqC5muTfk4zUZx1je5emf+1zBb60X
en15AdoSI/8zOVil0tUmiVO582KJpfALbUK+AwExzlimeqo/PXVcgxAJKD8VxjUi
TZa2MFeZCO+D01tMk1SzVLIx/Hv5o10MOiqL8jF1HNjmIYctsV8x
=ILYz
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEiK/NIGsWEZVxh/FrYKtH/8kJUicFAmXiFRgACgkQYKtH/8kJ
UieNURAAycjd4jonMyCs5SxwtDMLmcXt2xSQuAs5T2D1eBj3D0CC1Fi+CDq0gizP
0sSYbMaTGs4dHXY73fGVMGMmCNhmLjVt0wArX2egzBZlskYrk4il24nZR7geNQ1w
c0bW1uoCEVP19aO8FaIfdyfRGH4V2yIeugNoaDYrh7FrdRNwJMi00G1Alx5lja4S
ZtMvZ7FVjKUCoBUccctyOkEZxrqO/uvpE6EYKUaZFMiip5hdY3CQsFic9AjAv8XF
aeW6x8w7+KDKXXOGLRG+p1J3wysP2r91WcZd0wB8gYM2R6qCZt1irYVtdDf16x65
n+i4vlRouQYqUsll18EEQPj9Pin4iv6b2jZwAl20ZzHHZzpsbp4r8Zacqw4hLOwR
gaGHck4q/Nc++CeirvF7MptIC5kWCXu2+McKjx2bavM2C2p3ezhWQpo4Cbu2v93t
SvEQir25SvFJ1Y48S27nDPgRqt8dCMNCuatKbAPpqi1/jbwqi3coKZdRWYHf6iUT
e4x7cgNC1fms0Fdovx8VAcTsGBJITL4/VZ6/n6V6LcVHKtuSbX9swkyWso+kHYUt
ITFTgNK9oSrCITJ/a3VZLQSP5CyNJyuhYfUj/b5sqJY63T/yJGNkaPY2EaWqmyz8
2YHv+1hYKzsGAnt1ZEgKP8uy2T9N1CNWL3PYNGu6555wiNJAIrc=
=50d/
-----END PGP SIGNATURE-----
Merge tag 'ti-k3-dt-for-v6.9' of https://git.kernel.org/pub/scm/linux/kernel/git/ti/linux into soc/dt
TI K3 device tree updates for v6.9
New Features across family / New SoCs:
- J722s SoC and board support with OSPI NOR, CPSW ethernet
- Camera capture support on mulitple J7xx SoCs, AM68, AM69 and AM62P SoCs
- Wave5 Encoder/Decoder support for J721s2, J784s4 and AM62P
Generic Cleanups/Fixes:
- Stop spliting single mbox items
- Adds MIT license along with GPL-2.0 for all TI DTS files
- Moves PCIe EP nodes in overlays
- VTM Power domain fixups for J7xx SoCs
- Conversion of mmio mux users to reg-mux where possible
- Drops unnecessary UART pinmuxes on J7xx SoCs
- MMC TAP value updates for AM64/AM62A/AM62P for improved stability
- DSS register space updates for AM65/AM62/AM62A
SoC specific Fixes/Features:
J7200:
- Adds CAN support
- New compatible for J7200 to support IO wakeup
AM62A
- HDMI Display (DSS) support
- Move to simple-bus for main_conf node
- eMMC, additional MMC/SD instance support
AM62
- move to simple-bus for main_conf node
AM654
- IOT2050-SM board support
- IOT2050 DT refractoring.
AM64
- SolidRun AM642 HummingBoard-T support and its DT overlays
- ICSSG Ethernet support and associated peripherals
Board specific fixes/Features:
- Beagle Play MDIO and USB node fixes
- TPM support on k3-am642-phyboard-electra and verdin-am62-mallow
- Phycore-am64 ADC
- PCIe + USB2.0 SERDES and PCIe + USB3.0 SERDES card support
- USB1 support on verdin-am62
* tag 'ti-k3-dt-for-v6.9' of https://git.kernel.org/pub/scm/linux/kernel/git/ti/linux: (126 commits)
arm64: dts: ti: hummingboard-t: add overlays for m.2 pci-e and usb-3
arm64: dts: add description for solidrun am642 som and evaluation board
dt-bindings: arm: ti: Add bindings for SolidRun AM642 HummingBoard-T
arm64: dts: ti: k3-am62p: Add Wave5 Video Encoder/Decoder Node
arm64: dts: ti: k3-j721s2-main: Add Wave5 Video Encoder/Decoder Node
arm64: dts: ti: k3-j784s4: Add Wave5 Video Encoder/Decoder Node
arm64: dts: ti: k3-am69-sk: Add support for OSPI flash
arm64: dts: ti: k3-am69-sk: Enable CAN interfaces for AM69 SK board
arm64: dts: ti: Enable overlays for SK-AM62P
arm64: dts: ti: k3-am62p: Add nodes for CSI-RX
arm64: dts: ti: k3-am62p: Add DMASS1 for CSI
arm64: dts: ti: k3-am62p: Fix memory ranges for DMSS
arm64: dts: ti: k3-j722s-evm: Enable OSPI NOR support
arm64: dts: ti: k3-j722s-evm: Enable CPSW3G RGMII1
arm64: dts: ti: k3-j784s4-main: Fix mux-reg-masks in serdes_ln_ctrl
arm64: dts: ti: k3-j721e: Fix mux-reg-masks in hbmc_mux
arm64: dts: ti: Add common1 register space for AM62A SoC
arm64: dts: ti: Add common1 register space for AM62x SoC
arm64: dts: ti: Add common1 register space for AM65x SoC
arm64: dts: ti: k3-am642-evm: add overlay for ICSSG1 2nd port
...
Link: https://lore.kernel.org/r/e7e984db-47b9-404a-9471-5d2ed0effe1d@ti.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
HummingBoard-T features two M.2 connectors labeled "M1" and "M2".
The single SerDes lane of the SoC can be routed to either M1 pci-e
signals, or M2 usb-3 signals by a gpio-controlled mux.
Add overlays for each configuration.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Link: https://lore.kernel.org/r/20240219-add-am64-som-v7-4-0e6e95b0a05d@solid-run.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add description for the SolidRun AM642 SoM, and HummingBoard-T
evaluation board.
The SoM features:
- 1x cpsw ethernet with phy
- 2x pru ethernet with phy
- eMMC
- spi flash (assembly option)
Additionally microSD and usb-2.0 otg are included in the SoM
description as they are supported boot sources for the SOC boot-rom.
The Carrier provides:
- 3x RJ45 connector
- 2x M.2 connector
- USB-2.0 Hub
- USB-A Connector
- LEDs
- 2x CAN transceiver
- 1x RS485 transceiver
- sensors
The M.2 connectors support either USB-3.1 or PCI-E depending on status
of a mux. By default the mux is switched off.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Link: https://lore.kernel.org/r/20240219-add-am64-som-v7-3-0e6e95b0a05d@solid-run.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add the Chips and Media wave521cl video decoder/encoder node on J721S2.
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Brandon Brnich <b-brnich@ti.com>
Link: https://lore.kernel.org/r/20240220191413.3355007-3-b-brnich@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
AM69 SK has S28HS512T OSPI flash connected to MCU OSPI0.
Enable support for the same. Also describe the partition
information according to the offsets in the bootloader.
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Signed-off-by: Dasnavis Sabiya <sabiya.d@ti.com>
Link: https://lore.kernel.org/r/20240220162527.663394-3-sabiya.d@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
AM69 SK board has several CAN bus interfaces on both MCU and MAIN domains.
This enables the CAN interfaces on MCU and MAIN domain.
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Signed-off-by: Dasnavis Sabiya <sabiya.d@ti.com>
Link: https://lore.kernel.org/r/20240220162527.663394-2-sabiya.d@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Enable symbols so that overlays can be applied on the base DTB for
SK-AM62P.
Also compile-test known-to-work camera sensor overlays for OV5640 and
IMX219.
Reviewed-by: Vaishnav Achath <vaishnav.a@ti.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240220-am62p_csi-v2-4-3e71d9945571@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
AM62P supports image capture via the MIPI CSI-2 protocol, it uses three
IPs to achieve this: Cadence DPHY, Cadence CSI-RX, and TI's pixelgrabber
wrapper on top. Add nodes for these IPs in the devicetree, and keep them
disabled here, so these may be enabled by the sensor overlays.
Reviewed-by: Vaishnav Achath <vaishnav.a@ti.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240220-am62p_csi-v2-3-3e71d9945571@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
On AM62P, CSI-RX uses a dedicated BCDMA instance (DMASS1) for
transferring captured camera frames to DDR, so enable it.
Reviewed-by: Vaishnav Achath <vaishnav.a@ti.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240220-am62p_csi-v2-2-3e71d9945571@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The INTR module for DMASS1 (CSI specific DMASS) is outside the currently
available ranges, as it starts at 0x4e400000. So fix the ranges property
to enable programming the interrupts correctly.
Fixes: 29075cc09f ("arm64: dts: ti: Introduce AM62P5 family of SoCs")
Reviewed-by: Vaishnav Achath <vaishnav.a@ti.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240220-am62p_csi-v2-1-3e71d9945571@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
J722S EVM has S28HS512T 64 MiB Octal SPI NOR flash connected
to the OSPI interface, add support for the flash and describe
the partition information as per bootloader.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Link: https://lore.kernel.org/r/20240219090435.934383-3-vaishnav.a@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Enable MAC Port 1 of CPSW3G instance of CPSW Ethernet Switch in
RGMII-RXID mode of operation. Port 2 is not connected on the EVM,
thus keep it disabled.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Link: https://lore.kernel.org/r/20240219090435.934383-2-vaishnav.a@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Change offset in mux-reg-masks property for serdes_ln_ctrl node
since reg-mux property is used in compatible.
Fixes: 2765149273 ("mux: mmio: use reg property when parent device is not a syscon")
Signed-off-by: Chintan Vankar <c-vankar@ti.com>
Acked-by: Andrew Davis <afd@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://lore.kernel.org/r/20240213080348.248916-1-s-vadapalli@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Change offset in mux-reg-masks property for hbmc_mux node
since reg-mux property is used in compatible.
While here, update the reg region to include 4 bytes as this
is a 32bit register.
Fixes: 2765149273 ("mux: mmio: use reg property when parent device is not a syscon")
Suggested-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240215141957.13775-1-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
This adds common1 register space for AM62A SoC which is using TI's Keystone
display hardware and supporting it as described in
Documentation/devicetree/bindings/display/ti/ti,am65x-dss.yaml
Fixes: 3618811657 ("arm64: dts: ti: k3-am62a-main: Add node for Display SubSystem (DSS)")
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Aradhya Bhatia <a-bhatia1@ti.com>
Link: https://lore.kernel.org/r/20240216062426.4170528-5-devarsht@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
This adds common1 register space for AM62x SoC which is using TI's Keystone
display hardware and supporting it as described in
Documentation/devicetree/bindings/display/ti/ti,am65x-dss.yaml
Fixes: 8ccc1073c7 ("arm64: dts: ti: k3-am62-main: Add node for DSS")
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Aradhya Bhatia <a-bhatia1@ti.com>
Link: https://lore.kernel.org/r/20240216062426.4170528-4-devarsht@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
This adds common1 register space for AM65x SoC which is using TI's Keystone
display hardware and supporting it as described in
Documentation/devicetree/bindings/display/ti/ti,am65x-dss.yaml
Fixes: fc539b90ed ("arm64: dts: ti: am654: Add DSS node")
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Aradhya Bhatia <a-bhatia1@ti.com>
Link: https://lore.kernel.org/r/20240216062426.4170528-3-devarsht@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The am642-evm doesn't allow to enable 2 x CPSW3g ports and 2 x ICSSG1 ports
all together, so base k3-am642-evm.dts enables by default 2 x CPSW3g ports
and 1 x ICSSG1 ports, but it is also possible to support 1 x CPSW3g ports
and 2 x ICSSG1 ports configuration.
This patch adds overlay to support 1 x CPSW3g ports and 2 x ICSSG1 ports
configuration:
- Add label name 'mdio_mux_1' for 'mdio-mux-1' node so that the node
'mdio-mux-1' can be disabled in the overlay using the label name.
- disable 2nd CPSW3g port
- update CPSW3g pinmuxes to not use RGMII2
- disable mdio-mux-1 and define mdio-mux-2 to route ICSSG1 MDIO to the
shared DP83869 PHY
- add and enable ICSSG1 RGMII2 pinmuxes
- enable ICSSG1 MII1 port
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Link: https://lore.kernel.org/r/20240215103036.2825096-4-danishanwar@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
ICSSG1 provides dual Gigabit Ethernet support with proper FW loaded.
The ICSSG1 MII0 (RGMII1) has DP83869 PHY attached to it. The ICSSG1 shares
MII1 (RGMII2) PHY DP83869 with CPSW3g and it's assigned by default to
CPSW3g. The MDIO access to MII1 (RGMII2) PHY DP83869 is controlled by MDIO
bus switch and also assigned to CPSW3g. Therefore the ICSSG1 MII1 (RGMII2)
port is kept disable and ICSSG1 is enabled in single MAC mode by
default.
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Link: https://lore.kernel.org/r/20240215103036.2825096-3-danishanwar@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The ICSSG IP on AM64x SoCs have two Industrial Ethernet Peripherals (IEPs)
to manage/generate Industrial Ethernet functions such as time stamping.
Each IEP sub-module is sourced from an internal clock mux that can be
derived from either of the IP instance's ICSSG_IEP_GCLK or from another
internal ICSSG CORE_CLK mux. Add both the IEP nodes for both the ICSSG
instances. The IEP clock is currently configured to be derived
indirectly from the ICSSG_ICLK running at 250 MHz.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Link: https://lore.kernel.org/r/20240215103036.2825096-2-danishanwar@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Move bus-width property to *main.dtsi, above the OTAP/ITAP
delay values. While there is no error with where it is
currently at, it is easier to read the MMC node if the
bus-width property is located above the OTAP/ITAP delay
values consistently across MMC nodes.
Add missing bus-width for MMC2 in k3-am62-main.
Signed-off-by: Judith Mendez <jm@ti.com>
Tested-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20240213235701.2438513-9-jm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Move ti,clkbuf-sel property above the OTAP/ITAP delay values.
While there is no error with where it is currently at, it is
easier to read the MMC node if ti,clkbuf-sel is located above
the OTAP/ITAP delay values consistently across MMC nodes.
Add missing ti,clkbuf-sel for MMC0 in k3-am64-main.
Signed-off-by: Judith Mendez <jm@ti.com>
Tested-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20240213235701.2438513-8-jm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Remove DLL properties which are not applicable for soft PHYs
since these PHYs do not have a DLL to enable.
Acked-by: Francesco Dolcini <francesco.dolcini@toradex.com> # Verdin AM62
Signed-off-by: Judith Mendez <jm@ti.com>
Tested-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20240213235701.2438513-7-jm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add OTAP/ITAP values to enable HS400 timing for MMC0 and
SDR104 timing for MMC1/MMC2. Remove no-1-8-v property to
enable the highest speed mode possible.
Update MMC OTAP/ITAP values according to the datasheet
[0], refer to Table 7-79 for MMC0 and Table 7-97 for MMC1/MMC2.
[0] https://www.ti.com/lit/ds/symlink/am62p.pdf
Signed-off-by: Judith Mendez <jm@ti.com>
Link: https://lore.kernel.org/r/20240213235701.2438513-6-jm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add support for 32GB eMMC card on AM62A7 SK. Includes adding mmc0
pins settings. Add mmc0 alias for sdhci0 in k3-am62a7-sk.dts.
Signed-off-by: Nitin Yadav <n-yadav@ti.com>
Signed-off-by: Judith Mendez <jm@ti.com>
Link: https://lore.kernel.org/r/20240213235701.2438513-4-jm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Only Tx and Rx Signal lines for wkup_uart0 are brought out on
the J784S4 EVM from SoC, but CTS and RTS signal lines are not
brought on the EVM. Thus, remove pinmux for CTS and RTS signal
lines for wkup_uart0 in J784S4.
Fixes: 6fa5d37a2f ("arm64: dts: ti: k3-j784s4-evm: Add mcu and wakeup uarts")
Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com>
Link: https://lore.kernel.org/r/20240214105846.1096733-5-b-kapoor@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Only Tx and Rx Signal lines for wkup_uart0 are brought out on
the Common Proc Board through SoM, but CTS and RTS signal lines
are not brought on the board. Thus, remove pinmux for CTS and RTS
signal lines for wkup_uart0 in J721S2.
Fixes: f5e9ee0b35 ("arm64: dts: ti: k3-j721s2-common-proc-board: Add uart pinmux")
Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com>
Link: https://lore.kernel.org/r/20240214105846.1096733-4-b-kapoor@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
RPi v2 Camera (IMX219) is an 8MP camera that can be used with SK-AM69,
J721E SK, and AM68 SK through the 22-pin CSI-RX connector.
Add a reference overlay for dual IMX219 RPI camera v2 modules
which can be used across AM68 SK, AM69 SK, TDA4VM SK boards
that have a 15/22-pin FFC connector. Also enable build testing
and symbols for all the three platforms.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Reviewed-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240215085518.552692-10-vaishnav.a@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
J784S4 has three CSI2RX capture subsystem featuring Cadence CSI2RX,
DPHY and TI's pixel grabbing wrapper. Add nodes for the same and
keep them disabled by default. J784S4 uses a dedicated BCDMA instance
for CSI-RX traffic, so enable that as well.
J784S4 TRM (Section 12.7 Camera Subsystem):
https://www.ti.com/lit/zip/spruj52
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Reviewed-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240215085518.552692-9-vaishnav.a@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
J721S2 has two CSI2RX capture subsystem featuring Cadence CSI2RX,
DPHY and TI's pixel grabbing wrapper. Add nodes for the same and
keep them disabled by default. J721S2 uses a dedicated BCDMA instance
for CSI-RX traffic, so enable that as well.
J721S2 TRM (Section 12.7 Camera Subsystem):
https://www.ti.com/lit/zip/spruj28
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Reviewed-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240215085518.552692-8-vaishnav.a@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
J721E has two CSI2RX capture subsystem featuring Cadence CSI2RX,
DPHY and TI's pixel grabbing wrapper. Add nodes for the same and
keep them disabled by default.
J721E TRM (Section 12.7 Camera Subsystem):
https://www.ti.com/lit/zip/spruil1
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Reviewed-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240215085518.552692-7-vaishnav.a@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
J721E SK has the CSI2RX routed to a MIPI CSI connector and to 15-pin
RPi camera connector through an analog mux with GPIO control, model that
so that an overlay can control the mux state according to connected
cameras. Also provide labels to the I2C mux bus instances so that a
generic overlay can be used across multiple platforms.
J721E SK schematics: https://www.ti.com/lit/zip/sprr438
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Reviewed-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240215085518.552692-6-vaishnav.a@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
CSI cameras are controlled using I2C. On AM69 Starter Kit, this is routed
to I2C-1, so enable the instance, TCA9543 I2C switch and the TCA6408
GPIO expander on the bus. AM69 SK has the CSI2RX routed to a MIPI CSI
connector and to 22-pin RPi camera connector through an analog mux with
GPIO control, model that so that an overlay can control the mux state
according to connected cameras.
AM69 SK schematics: https://www.ti.com/lit/zip/sprr466
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Reviewed-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240215085518.552692-5-vaishnav.a@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
CSI cameras are controlled using I2C. On AM68 Starter Kit, this is routed
to I2C-1, so enable the instance and the TCA9543 I2C switch on the bus.
AM68 SK schematics: https://www.ti.com/lit/zip/sprr463
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Reviewed-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240215085518.552692-4-vaishnav.a@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
CSI cameras are controlled using I2C. On J784S4 EVM, this is routed
to I2C-5, so enable the instance and the TCA6408 GPIO expander
on the bus.
J784S4 EVM schematics: https://www.ti.com/lit/zip/sprr458
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Reviewed-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240215085518.552692-3-vaishnav.a@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
This patch adds a reserved memory for the TI AM65X platform watchdog
to reserve the specific info, triggering the watchdog reset in last
boot, to know if the board reboot is due to a watchdog reset.
Signed-off-by: Li Hua Qian <huaqian.li@siemens.com>
Link: https://lore.kernel.org/r/20240117060654.109424-1-huaqian.li@siemens.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The J722S is a family of application processors built for Automotive and
Linux Application development. J722S family of SoCs is a superset of the
AM62P SoC family and shares similar memory map, thus the nodes are being
reused from AM62P includes instead of duplicating the definitions.
Some highlights of J722S SoC (in addition to AM62P SoC features) are:
* Two Cortex-R5F for Functional Safety or general-purpose usage and
two C7x floating point vector DSP with Matrix Multiply Accelerator
for deep learning.
* Vision Processing Accelerator (VPAC) with image signal processor
and Depth and Motion Processing Accelerator (DMPAC).
* 7xUARTs, 3xSPI, 5xI2C, 2xUSB2, 2xCAN-FD, 3xMMC and SD, GPMC for
NAND/FPGA connection, OSPI memory controller, 5xMcASP for audio,
4xCSI-RX for Camera, 1 PCIe Gen3 controller, USB3.0 eCAP/eQEP,
ePWM, among other peripherals.
For those interested, more details about this SoC can be found in the
Technical Reference Manual here:
https://www.ti.com/lit/zip/sprujb3
Co-developed-by: Jayesh Choudhary <j-choudhary@ti.com>
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Reviewed-by: Manorit Chawdhry <m-chawdhry@ti.com>
Link: https://lore.kernel.org/r/20240206100608.127702-3-vaishnav.a@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Main differences between the new variant and Advanced PG2:
1. Arduino interface is removed. Instead, an new ASIC is added for
communicating with PLC 1200 signal modules.
2. USB 3.0 type A connector is removed, only USB 2.0 type A connector is
available.
3. DP interface is removed. Instead, to communicate with PLC 1200 signal
modules, a USB 3.0 type B connector is added but the signals are
actually not USB.
4. DDR size is increased to 4 GB.
5. Two sensors are added, one tilt sensor and one light sensor.
The light sensor it not yet added to the DT at this stage as it depends
on to-be-added bindings.
Co-developed-by: Chao Zeng <chao.zeng@siemens.com>
Signed-off-by: Chao Zeng <chao.zeng@siemens.com>
Co-developed-by: Li Hua Qian <huaqian.li@siemens.com>
Signed-off-by: Li Hua Qian <huaqian.li@siemens.com>
Signed-off-by: Baocheng Su <baocheng.su@siemens.com>
[Jan: rebase over dtsi refactorings, split-out light sensor, improve LEDs]
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Link: https://lore.kernel.org/r/d24e920547986499f6e8e39c833e414679b12ab4.1707463401.git.jan.kiszka@siemens.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
There is a variant coming which does not support the Display Port. Move
all related bits into a separate dtsi so that only those variants
supporting the interface can include it.
Along that, remove a redundant clock setting from
k3-am65-iot2050-common-pg1.dtsi.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Link: https://lore.kernel.org/r/3397d917d7c97f7aec05bc5f65eef3a6fe843650.1707463401.git.jan.kiszka@siemens.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
A new variant is to be added which will not have a arduino connector
like the existing ones. Factor out all bits that are specific to this
connector.
The split is not perfect because wkup_gpio0 is defined based on what is
common to all variants having the connector, thus containing also
connector-unrelated information. But this is still cleaner than
replicating this node into all 4 variants.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Link: https://lore.kernel.org/r/3366367dc9f190c9e21027b9a810886791e99245.1707463401.git.jan.kiszka@siemens.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The R5 lockstep disabling should be common for all PG2 boards, move it
from variants dts to common-pg2.dtsi.
As now the Basic PG2 consumes this twice, move Basic disabling to the
PG1 variant.
Signed-off-by: Baocheng Su <baocheng.su@siemens.com>
[Jan: avoid duplication of disabling for Basic PG2]
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Link: https://lore.kernel.org/r/f692d0211915aefd4de7c9ecff5234683c9c7d59.1707463401.git.jan.kiszka@siemens.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
AM62 USB works with some devices, while failing to operate with others.
[ 560.189822] xhci-hcd xhci-hcd.4.auto: xHCI Host Controller
[ 560.195631] xhci-hcd xhci-hcd.4.auto: new USB bus registered, assigned bus number 2
[ 574.388509] xhci-hcd xhci-hcd.4.auto: can't setup: -110
[ 574.393814] xhci-hcd xhci-hcd.4.auto: USB bus 2 deregistered
[ 574.399544] xhci-hcd: probe of xhci-hcd.4.auto failed with error -110
This seems to be related to LPM (Link Power Management), and disabling it
turns USB into reliable working state.
As per AM62 reference manual:
> 4.8.2.1 USB2SS Unsupported Features
>
> The following features are not supported on this family of devices:
> ...
> - USB 2.0 ECN: Link Power Management (LPM)
> ...
Fixes: 2240f96cf3 ("arm64: dts: ti: k3-am62-main: Add support for USB")
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Link: https://lore.kernel.org/r/20240209130213.38908-1-andrejs.cainikovs@gmail.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Set VDD_CORE minimum voltage to 0.75V, TI AM62 can run at either 0.75V
or 0.85V depending on the actual speed grade and on the maximum
configured speed (1.4GHz frequency requires 0.85V).
The actual value is programmed into the PMIC EEPROM during manufacturing
(according to the SOC speed grade) and this ensure that both the voltage
values are valid and therefore the OS will not overwrite the value
programmed into the PMIC.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://lore.kernel.org/r/20240213155622.18309-1-francesco@dolcini.it
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The devices in the wkup domain are capable of waking up the system from
suspend. We can configure the wkup domain devices in a generic way using
the ti-sysc interconnect target module driver like we have done with the
earlier TI SoCs.
As ti-sysc manages the SYSCONFIG related registers independent of the
child hardware device, the wake-up configuration is also set even if
wkup_uart0 is reserved by sysfw.
The wkup_uart0 device has interconnect target module register mapping like
dra7 wkup uart. There is a 1 MB interconnect target range with one uart IP
block in the target module. The power domain and clock affects the whole
interconnect target module.
Note we change the functional clock name to follow the ti-sysc binding
and use "fck" instead of "fclk".
Also note that we need to disable the target module reset as noted by
Markus. Otherwise the sysfw using wkup_uart0 can get confused on some
devices leading to boot time issues such as mbox timeouts.
Tested-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Markus Schneider-Pargmann <msp@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20240213112510.6334-1-tony@atomide.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The phyBOARD-Lyra has a GPIO fan header. This overlay enables the fan
header and sets the fan to turn on at 65C.
Signed-off-by: Nathan Morrisson <nmorrisson@phytec.com>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20240213005248.1027842-1-nmorrisson@phytec.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The tps659413 and tps659411 nodes set WKUP_GPIO0_7 (G28) pin as input
to be used as PMIC interrupt but uses 9 (WKUP_GPIO0_9) as
"interrupts" property.
Replace 9 by 7 for both tps659413 and tps659411 after checking in the
board schematic [1].
[1] https://www.ti.com/tool/SK-TDA4VM
Fixes: b808cef0be ("arm64: dts: ti: k3-j721e-sk: Add TPS6594 family PMICs")
Cc: Neha Malcom Francis <n-francis@ti.com>
Signed-off-by: Romain Naour <romain.naour@smile.fr>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Link: https://lore.kernel.org/r/20240209171146.307465-2-romain.naour@smile.fr
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The tps659413 node set WKUP_GPIO0_83 (AA37) pin as input to be used as
PMIC interrupt but uses 39 (WKUP_GPIO0_39) as "interrupts" property.
Replace 39 by 83 after checking in the board schematic [1].
[1] https://www.ti.com/tool/SK-AM69
Fixes: 865a1593bf ("arm64: dts: ti: k3-am69-sk: Add support for TPS6594 PMIC")
Cc: Neha Malcom Francis <n-francis@ti.com>
Signed-off-by: Romain Naour <romain.naour@smile.fr>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Link: https://lore.kernel.org/r/20240209171146.307465-1-romain.naour@smile.fr
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add support for Verdin USB1 interface, implements role switch
functionality using "gpio-usb-b-connector", VBUS is also now
controlled with "regulator-fixed" using a standard GPIO.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://lore.kernel.org/r/20240209130106.38739-1-andrejs.cainikovs@gmail.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Enable both SERDES and PCIe DT nodes in order to get PCIe working on
the SERDES PCIe x2 personality card.
The daughter card also has a USB 2.0 dual-role port. As the base board
already supports a 2.0 dual-role port, enable the port on the SERDES
card to be a host only port.
This will prevent user confusion as having 2 ports in device mode often
leads to confusion as to which port is bound to the gadget function driver.
The PCIe x2 card is provided with the AM65x IDK configuration [1]
so apply the overlay to k3-am654-idk.dtb
[1] https://www.ti.com/lit/ug/spruim6a/spruim6a.pdf
Co-developed-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Link: https://lore.kernel.org/r/20240208-for-v6-9-am65-overlays-2-0-v2-2-70bae3e91597@kernel.org
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add the overlay dtbo file to a Makefile target so it can be
picked by the dtbs_install command.
Fixes: b8690ed3d1 ("arm64: dts: ti: am65x: Add Rocktech OLDI panel DT overlay")
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Aradhya Bhatia <a-bhatia1@ti.com>
Link: https://lore.kernel.org/r/20240208-for-v6-9-am65-overlays-2-0-v2-1-70bae3e91597@kernel.org
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The main_conf node does not need to be a syscon, so change to
"simple-bus". This removes a DTS check warning.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240124184722.150615-11-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The main_conf node does not need to be a syscon, so change to
"simple-bus". This removes a DTS check warning.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240124184722.150615-10-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
To do this we convert hbmc-mux to "reg-mux", then the FSS node
does not need to be a syscon, so change to "simple-bus". This
removes a DTS check warning.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240124184722.150615-9-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
This removes a dependency on the parent node being a syscon node.
Convert from mmio-mux to reg-mux adjusting node name and properties
as needed.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240124184722.150615-8-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
This removes a dependency on the parent node being a syscon node.
Convert from mmio-mux to reg-mux adjusting node name and properties
as needed.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240124184722.150615-7-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
This removes a dependency on the parent node being a syscon node.
Convert from mmio-mux to reg-mux adjusting node name and properties
as needed.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240124184722.150615-6-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
This removes a dependency on the parent node being a syscon node.
Convert from mmio-mux to reg-mux adjusting node name and properties
as needed.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240124184722.150615-5-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
This removes a dependency on the parent node being a syscon node.
Convert from mmio-mux to reg-mux adjusting node name and properties
as needed.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240124184722.150615-4-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
This removes a dependency on the parent node being a syscon node.
Convert from mmio-mux to reg-mux adjusting node name and properties
as needed.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240124184722.150615-3-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
This removes a dependency on the parent node being a syscon node.
Convert from mmio-mux to reg-mux adjusting node name and properties
as needed.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240124184722.150615-1-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
SPDX identifier GPL-2.0 has been deprecated since license list version
3.0. Use GPL-2.0-only to be specific.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20240122145539.194512-17-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
SPDX identifier GPL-2.0 has been deprecated since license list version
3.0. Use GPL-2.0-only to be specific.
Cc: Chao Zeng <chao.zeng@siemens.com>
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Le Jin <le.jin@siemens.com>
Acked-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20240122145539.194512-16-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Modify license to include dual licensing as GPL-2.0-only OR MIT
license for device trees belonging to PHYTEC Messtechnik GmbH and
PHYTEC America, LLC platforms. This allows for Linux kernel device
tree to be used in other Operating System ecosystems such as Zephyr or
FreeBSD.
While at this, update the GPL-2.0 to be GPL-2.0-only to be in sync
with latest SPDX conventions (GPL-2.0 is deprecated).
While at this, update the copyright year to sync with current year
to indicate license change.
Cc: Garrett Giordano <ggiordano@phytec.com>
Cc: Wadim Egorov <w.egorov@phytec.de>
Acked-by: Garrett Giordano <ggiordano@phytec.com>
Acked-by: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20240122145539.194512-15-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Modify license to include dual licensing as GPL-2.0-only OR MIT
license for device trees belonging to BeagleBoard.org Foundation
platforms. This allows for Linux kernel device tree to be used in
other Operating System ecosystems such as Zephyr or FreeBSD.
While at this, update the GPL-2.0 to be GPL-2.0-only to be in sync
with latest SPDX conventions (GPL-2.0 is deprecated).
While at this, update the copyright year to sync with current year
to indicate license change.
Cc: Ayush Singh <ayushdevel1325@gmail.com>
Cc: Jason Kridner <jkridner@beagleboard.org>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Cc: Robert Nelson <robertcnelson@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Wadim Egorov <w.egorov@phytec.de>
Acked-by: Ayush Singh <ayushdevel1325@gmail.com>
Acked-by: Jason Kridner <jkridner@beagleboard.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Robert Nelson <robertcnelson@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20240122145539.194512-14-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Modify license to include dual licensing as GPL-2.0-only OR MIT
license for SoC and TI evm device tree files. This allows for Linux
kernel device tree to be used in other Operating System ecosystems
such as Zephyr or FreeBSD.
While at this, update the GPL-2.0 to be GPL-2.0-only to be in sync
with latest SPDX conventions (GPL-2.0 is deprecated).
While at this, update the TI copyright year to sync with current year
to indicate license change.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20240122145539.194512-13-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Modify license to include dual licensing as GPL-2.0-only OR MIT
license for SoC and TI evm device tree files. This allows for Linux
kernel device tree to be used in other Operating System ecosystems
such as Zephyr or FreeBSD.
While at this, update the GPL-2.0 to be GPL-2.0-only to be in sync
with latest SPDX conventions (GPL-2.0 is deprecated).
While at this, update the TI copyright year to sync with current year
to indicate license change.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20240122145539.194512-12-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Modify license to include dual licensing as GPL-2.0-only OR MIT
license for SoC and TI evm device tree files. This allows for Linux
kernel device tree to be used in other Operating System ecosystems
such as Zephyr or FreeBSD.
While at this, update the GPL-2.0 to be GPL-2.0-only to be in sync
with latest SPDX conventions (GPL-2.0 is deprecated).
While at this, update the TI copyright year to sync with current year
to indicate license change (and add it at least for one file which was
missing TI copyright).
Cc: Apelete Seketeli <aseketeli@baylibre.com>
Cc: Jerome Neanne <jneanne@baylibre.com>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20240122145539.194512-11-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Modify license to include dual licensing as GPL-2.0-only OR MIT
license for SoC and TI evm device tree files. This allows for Linux
kernel device tree to be used in other Operating System ecosystems
such as Zephyr or FreeBSD.
While at this, update the GPL-2.0 to be GPL-2.0-only to be in sync
with latest SPDX conventions (GPL-2.0 is deprecated).
While at this, update the TI copyright year to sync with current year
to indicate license change (and add it at least for one file which was
missing TI copyright).
Cc: Esteban Blanc <eblanc@baylibre.com>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Cc: Pierre Gondois <pierre.gondois@arm.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Esteban Blanc <eblanc@baylibre.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Pierre Gondois <pierre.gondois@arm.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20240122145539.194512-10-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Modify license to include dual licensing as GPL-2.0-only OR MIT
license for SoC and TI evm device tree files. This allows for Linux
kernel device tree to be used in other Operating System ecosystems
such as Zephyr or FreeBSD.
While at this, update the GPL-2.0 to be GPL-2.0-only to be in sync
with latest SPDX conventions (GPL-2.0 is deprecated).
While at this, update the TI copyright year to sync with current year
to indicate license change (and add it at least for one file which was
missing TI copyright).
Cc: "Alexander A. Klimov" <grandmaster@al2klimov.de>
Cc: Jerome Neanne <jneanne@baylibre.com>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Pierre Gondois <pierre.gondois@arm.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Pierre Gondois <pierre.gondois@arm.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20240122145539.194512-9-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Modify license to include dual licensing as GPL-2.0-only OR MIT
license for SoC and TI evm device tree files. This allows for Linux
kernel device tree to be used in other Operating System ecosystems
such as Zephyr or FreeBSD.
While at this, update the GPL-2.0 to be GPL-2.0-only to be in sync
with latest SPDX conventions (GPL-2.0 is deprecated).
While at this, update the TI copyright year to sync with current year
to indicate license change (and add it at least for one file which was
missing TI copyright).
Cc: Esteban Blanc <eblanc@baylibre.com>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Cc: Pierre Gondois <pierre.gondois@arm.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Esteban Blanc <eblanc@baylibre.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Pierre Gondois <pierre.gondois@arm.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20240122145539.194512-8-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Modify license to include dual licensing as GPL-2.0-only OR MIT
license for SoC and TI evm device tree files. This allows for Linux
kernel device tree to be used in other Operating System ecosystems
such as Zephyr or FreeBSD.
While at this, update the GPL-2.0 to be GPL-2.0-only to be in sync
with latest SPDX conventions (GPL-2.0 is deprecated).
While at this, update the TI copyright year to sync with current year
to indicate license change (and add it at least for one file which was
missing TI copyright).
Cc: "Alexander A. Klimov" <grandmaster@al2klimov.de>
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Cc: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Cc: Pierre Gondois <pierre.gondois@arm.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Acked-by: Pierre Gondois <pierre.gondois@arm.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20240122145539.194512-7-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Modify license to include dual licensing as GPL-2.0-only OR MIT
license for SoC and TI evm device tree files. This allows for Linux
kernel device tree to be used in other Operating System ecosystems
such as Zephyr or FreeBSD.
While at this, update the GPL-2.0 to be GPL-2.0-only to be in sync
with latest SPDX conventions (GPL-2.0 is deprecated).
While at this, update the TI copyright year to sync with current year
to indicate license change (and add it at least for one file which was
missing TI copyright).
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Cc: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Cc: Pierre Gondois <pierre.gondois@arm.com>
Cc: Roger Quadros <rogerq@kernel.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Wadim Egorov <w.egorov@phytec.de>
Acked-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Acked-by: Pierre Gondois <pierre.gondois@arm.com>
Acked-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20240122145539.194512-6-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Modify license to include dual licensing as GPL-2.0-only OR MIT
license for SoC and TI evm device tree files. This allows for Linux
kernel device tree to be used in other Operating System ecosystems
such as Zephyr or FreeBSD.
While at this, update the GPL-2.0 to be GPL-2.0-only to be in sync
with latest SPDX conventions (GPL-2.0 is deprecated).
While at this, update the TI copyright year to sync with current year
to indicate license change (and add it at least for one file which was
missing TI copyright).
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20240122145539.194512-5-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Modify license to include dual licensing as GPL-2.0-only OR MIT
license for SoC and TI evm device tree files. This allows for Linux
kernel device tree to be used in other Operating System ecosystems
such as Zephyr or FreeBSD.
While at this, update the GPL-2.0 to be GPL-2.0-only to be in sync
with latest SPDX conventions (GPL-2.0 is deprecated).
While at this, update the TI copyright year to sync with current year
to indicate license change (and add it at least for one file which was
missing TI copyright).
Cc: Guillaume La Roque <glaroque@baylibre.com>
Cc: Julien Panis <jpanis@baylibre.com>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Cc: Pierre Gondois <pierre.gondois@arm.com>
Cc: Roger Quadros <rogerq@kernel.org>
Cc: Ronald Wahl <ronald.wahl@raritan.com>
Cc: Sarah Walker <sarah.walker@imgtec.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Guillaume La Roque <glaroque@baylibre.com>
Acked-by: Julien Panis <jpanis@baylibre.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Pierre Gondois <pierre.gondois@arm.com>
Acked-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Ronald Wahl <ronald.wahl@raritan.com>
Acked-by: Sarah Walker <sarah.walker@imgtec.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20240122145539.194512-4-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Modify license to include dual licensing as GPL-2.0-only OR MIT
license for SoC and TI evm device tree files. This allows for Linux
kernel device tree to be used in other Operating System ecosystems
such as Zephyr or FreeBSD.
While at this, update the GPL-2.0 to be GPL-2.0-only to be in sync with
latest SPDX conventions (GPL-2.0 is deprecated).
While at this, update the TI copyright year to sync with current year to
indicate license change (and add it at least for one file which was
missing TI copyright).
Cc: Julien Panis <jpanis@baylibre.com>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Cc: Pierre Gondois <pierre.gondois@arm.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Julien Panis <jpanis@baylibre.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Pierre Gondois <pierre.gondois@arm.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20240122145539.194512-3-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
For suspend to ram on j7200, use ti,j7200-padconf compatible to save and
restore pinctrl contexts.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20231128-j7200-pinctrl-s2r-v1-3-704e7dc24460@bootlin.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
K3 Remoteproc R5 driver requires reserved memory carveouts and
mailbox configuration to instantiate the cores successfully.
Since this is a board level dependency, keep the R5 subsytem
disabled at SoC dtsi, otherwise it results in probe errors like
below during AM62P SK boot:
r5fss@79000000: reserved memory init failed, ret = -22
r5fss@79000000: k3_r5_cluster_rproc_init failed, ret = -22
r5fss@78000000: reserved memory init failed, ret = -22
r5fss@78000000: k3_r5_cluster_rproc_init failed, ret = -22
Fixes: b5080c7c1f ("arm64: dts: ti: k3-am62p: Add nodes for more IPs")
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Reviewed-by: Jayesh Choudhary <j-choudhary@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20240121134017.374992-1-vaishnav.a@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
VP2 and VP3 are unused video ports and VP3 share the same parent
clock as VP1 causing issue with pixel clock setting for HDMI (VP1).
The current DM firmware does not support changing parent clock if it
is shared by another component. It returns 0 for the determine_rate
query before causing set_rate to set the clock at default maximum of
1.8GHz which is a lot more than the maximum frequency videoports can
support (600MHz) causing SYNC LOST issues.
So remove the parent clocks for unused VPs to avoid conflict.
Fixes: 6f8605fd7d ("arm64: dts: ti: k3-am69-sk: Add DP and HDMI support")
Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Aradhya Bhatia <a-bhatia1@ti.com>
Tested-by: Enric Balletbo i Serra <eballetbo@redhat.com>
Link: https://lore.kernel.org/r/20240201142308.4954-1-j-choudhary@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
HDMI audio can be enabled over AM62A-SK using the same DT overlay that
is used for AM625 / AM62-LP SK-EVMs.
Add the sk.dtb + hdmi-audio.dtbo combination for AM62A7-SK as well, to
check for overlay applicability during DTBS compile tests.
Signed-off-by: Aradhya Bhatia <a-bhatia1@ti.com>
Link: https://lore.kernel.org/r/20240201125452.1920623-4-a-bhatia1@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The DSS outputs DPI signals via its second video port (VP2). The DPI
output from DSS is 24 bits (RGB888) and is forwarded to an HDMI
transmitter (SIL9022) on the board.
Add pinmux info for DSS DPI output.
Add DT nodes for SIL9022 HDMI transmitter (TX), and the HDMI connector
on the AM62A7-SK platforms.
Additionally, connect the output of DSS (VP2) with input of the HDMI TX,
and the output of HDMI TX to the input of the HDMI connector.
Signed-off-by: Aradhya Bhatia <a-bhatia1@ti.com>
Link: https://lore.kernel.org/r/20240201125452.1920623-3-a-bhatia1@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add Display SubSystem (DSS) DT node for the AM62A7 SoC.
The DSS supports one each of video pipeline (vid) and video-lite
pipeline (vidl1). The video port 1 (vp1) is tied-off in AM62A SoC, but
the pipeline remains active. The video port 2 (vp2) outputs the DPI
signals. Both the video ports are connected to the pipelines via 2
identical overlay managers (ovr1 and ovr2).
Signed-off-by: Aradhya Bhatia <a-bhatia1@ti.com>
Link: https://lore.kernel.org/r/20240201125452.1920623-2-a-bhatia1@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Enable the CPSW MDIO node, and link the pinctrl information to enable
ethernet on SK-AM62P.
Ethernet was unintentally broken on this board, even though these nodes
were already present, as enabling them was missed in the original
patch.
Fixes: c00504ea42 ("arm64: dts: ti: k3-am62p5-sk: Updates for SK EVM")
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240201-am62p_cpsw_mdio-v1-1-05f758300f6e@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
CAN instances 0 and 1 in the mcu domain are brought on the common
processor board through headers J30 and J31 respectively. Thus, add
their respective transceivers 1 and 2 dt nodes to add support for
these CAN instances.
CAN instance 3 in the main domain is brought on the common
processor board through header J27. The CAN High and Low lines
from the SoC are routed through a mux on the SoM. The select lines need
to be set for the CAN signals to get connected to the transceiver 3 on
the common processor board. Therefore, add transceiver dt nodes to add
support for this CAN instance.
Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com>
Link: https://lore.kernel.org/r/20240130102044.120483-4-b-kapoor@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
CAN instance 0 in the main domain is brought on the J7200 SoM through
header J1. Thus, Add transceiver dt node to add support for this CAN
instance.
Also, add the mux dt nodes to route CAN High and Low lines coming
from the SoC to the Common Processor Board.
Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com>
Link: https://lore.kernel.org/r/20240130102044.120483-3-b-kapoor@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add support for 18 CAN controllers in main domain and 2 CAN controllers
present in mcu domain. All the CAN controllers support classic CAN
messages as well as CAN_FD messages.
Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com>
Link: https://lore.kernel.org/r/20240130102044.120483-2-b-kapoor@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add TPM device to Mallow device tree file, the device is connected to
the SoC with SPI1/CS1, the same SPI interface is also available on an
extension header together with an additional CS0 signal.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://lore.kernel.org/r/20240126165136.28543-1-francesco@dolcini.it
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
This node is an example node for the PCIe controller in "endpoint" mode.
By default the controller is in "root complex" mode and there is already a
DT node for the same.
Examples should go in the bindings or other documentation.
Remove this node.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240124183659.149119-4-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
These nodes are example nodes for the PCIe controller in "endpoint" mode.
By default the controller is in "root complex" mode and there is already a
DT node for the same.
Examples should go in the bindings or other documentation.
Remove this node.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240124183659.149119-3-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
This node is an example node for the PCIe controller in "endpoint" mode.
By default the controller is in "root complex" mode and there is already a
DT node for the same.
Examples should go in the bindings or other documentation.
Remove this node.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240124183659.149119-2-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
PCIe node defined in the top-level J7200 SoC dtsi file is incomplete
and will not be functional unless it is extended with a SerDes PHY.
As the PHY and mode is only known at the board integration level, this
node should only be enabled when provided with this information.
Disable the PCIe node in the dtsi files and only enable when it is
actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240124183659.149119-1-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Each "mboxes" item is composed of two cells. It seems these got split
as they appeared to be two items in an array, but are actually a single
two-cell item. Rejoin these cells.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240123222536.875797-11-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Each "mboxes" item is composed of two cells. It seems these got split
as they appeared to be two items in an array, but are actually a single
two-cell item. Rejoin these cells.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240123222536.875797-10-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Each "mboxes" item is composed of two cells. It seems these got split
as they appeared to be two items in an array, but are actually a single
two-cell item. Rejoin these cells.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240123222536.875797-9-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Each "mboxes" item is composed of two cells. It seems these got split
as they appeared to be two items in an array, but are actually a single
two-cell item. Rejoin these cells.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240123222536.875797-8-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Each "mboxes" item is composed of two cells. It seems these got split
as they appeared to be two items in an array, but are actually a single
two-cell item. Rejoin these cells.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240123222536.875797-7-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Each "mboxes" item is composed of two cells. It seems these got split
as they appeared to be two items in an array, but are actually a single
two-cell item. Rejoin these cells.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240123222536.875797-6-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Each "mboxes" item is composed of two cells. It seems these got split
as they appeared to be two items in an array, but are actually a single
two-cell item. Rejoin these cells.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240123222536.875797-5-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Each "mboxes" item is composed of two cells. It seems these got split
as they appeared to be two items in an array, but are actually a single
two-cell item. Rejoin these cells.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240123222536.875797-4-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Each "mboxes" item is composed of two cells. It seems these got split
as they appeared to be two items in an array, but are actually a single
two-cell item. Rejoin these cells.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240123222536.875797-3-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Each "mboxes" item is composed of two cells. It seems these got split
as they appeared to be two items in an array, but are actually a single
two-cell item. Rejoin these cells.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240123222536.875797-2-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Each "mboxes" item is composed of two cells. It seems these got split
as they appeared to be two items in an array, but are actually a single
two-cell item. Rejoin these cells.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240123222536.875797-1-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The phyBOARD-Electra populates a TPM module on SPI0 bus.
Add support for the Infineon SLB9670 TPM module.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20240123102921.1348777-1-w.egorov@phytec.de
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The clock on the ethernet1 PHY is turned on by default. This turns
the clock off as we do not use it.
Signed-off-by: Nathan Morrisson <nmorrisson@phytec.com>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20240119225257.403222-1-nmorrisson@phytec.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
memory node are required for bootloader operation on TI K3 J784S4 EVM
and AM69-SK boards for finding the memory size during early boot stage.
So, align Linux device tree by adding phase tag marking 'bootph-all',
which is to enable for all bootloader stages.
Signed-off-by: Apurva Nandan <a-nandan@ti.com>
Link: https://lore.kernel.org/r/20240119171619.3759205-1-a-nandan@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The beagleplay dts was using a bit-bang gpio mdio bus as a work-around
for errata i2329. However since commit d04807b806 ("net: ethernet: ti:
davinci_mdio: Add workaround for errata i2329") the mdio driver itself
already takes care of this errata for effected silicon, which landed
well before the beagleplay dts. So i suspect the reason for the
workaround in upstream was simply due to copying the vendor dts.
Switch the dts to the ti,cpsw-mdio instead so it described the actual
hardware and is consistent with other AM625 based boards
Signed-off-by: Sjoerd Simons <sjoerd@collabora.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240112124505.2054212-1-sjoerd@collabora.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The USB0 port on the beagleplay can be used for DFU booting. To enable
that functionality mark with bootph-all.
Signed-off-by: Sjoerd Simons <sjoerd@collabora.com>
Link: https://lore.kernel.org/r/20240112091745.1896922-3-sjoerd@collabora.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The USB0 port on the AM62x SK can be used for DFU booting. To enable
that functionality mark with bootph-all.
Signed-off-by: Sjoerd Simons <sjoerd@collabora.com>
Link: https://lore.kernel.org/r/20240112091745.1896922-2-sjoerd@collabora.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add SGX GPU device entry to base AM654 dtsi file.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Message-ID: <20240109171950.31010-10-afd@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DDR50 speed mode is enabled for MMCSD in J784s4 but its Itap Delay
Value is not present in the device tree. Thus, add Itap Delay Value
for MMCSD High Speed DDR which is DDR50 speed mode for J784s4 SoC
according to datasheet for J784s4.
[+] Refer to : section 7.10.5.17.2 MMC1/2 - SD/SDIO Interface, in
J784s4 datasheet
- https://www.ti.com/lit/ds/symlink/tda4vh-q1.pdf
Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com>
Reviewed-by: Judith Mendez <jm@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20231201082045.790478-4-b-kapoor@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
DDR50 speed mode is enabled for MMCSD in J721s2 but its Itap Delay
Value is not present in the device tree. Thus, add Itap Delay Value
for MMCSD High Speed DDR which is DDR50 speed mode for J721s2 SoC
according to datasheet for J721s2.
[+] Refer to : section 7.10.5.17.2 MMC1/2 - SD/SDIO Interface, in
J721s2 datasheet
- https://www.ti.com/lit/ds/symlink/tda4vl-q1.pdf
Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com>
Reviewed-by: Judith Mendez <jm@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20231201082045.790478-3-b-kapoor@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
DDR52 speed mode is enabled for eMMC in J7200 but its Itap Delay Value
is not present in the device tree. Thus, add Itap Delay Value for eMMC
High Speed DDR which is DDR52 speed mode for J7200 SoC according to
datasheet for J7200.
[+] Refer to : section 7.9.5.16.1 MMCSD0 - eMMC Interface, in
J7200 datasheet
- https://www.ti.com/lit/ds/symlink/dra821u-q1.pdf
Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com>
Reviewed-by: Judith Mendez <jm@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20231201082045.790478-2-b-kapoor@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Add additional reg properties for BCDMA and PKTDMA nodes which are
mostly used by bootloader components before Device Manager firmware
services are available, in order to setup DMA transfers.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20231213135138.929517-4-vigneshr@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Add additional reg properties for UDMA and RingAcc nodes which are
mostly used by bootloader components before Device Manager firmware
services are available, in order to setup DMA transfers.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20231213135138.929517-3-vigneshr@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Add additional reg properties for UDMA and RingAcc nodes which are
mostly used by bootloader components before Device Manager firmware
services are available, in order to setup DMA transfers.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20231213135138.929517-2-vigneshr@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Add the Series AXE GPU node to the AM62 device tree.
Tested-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Signed-off-by: Sarah Walker <sarah.walker@imgtec.com>
Signed-off-by: Donald Robson <donald.robson@imgtec.com>
Acked-by: Darren Etheridge <detheridge@ti.com>
Link: https://lore.kernel.org/r/7088cc032374ae517191b1dadf5bb5f0440eac81.1701773390.git.donald.robson@imgtec.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Add overlay to enable the PCIE1 instance of PCIe on J721S2-EVM in
Endpoint mode of operation.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Reviewed-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20231211115535.1264353-3-s-vadapalli@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Add overlay to enable the PCIE0 instance of PCIe on J721E-EVM in
Endpoint mode of operation.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Reviewed-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20231211115535.1264353-2-s-vadapalli@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
This patch adds support for TPS6594 PMIC family on wakeup I2C0 bus.
These devices provide regulators (bucks and LDOs), but also GPIOs, a
RTC, a watchdog, an ESM (Error Signal Monitor) which monitors the SoC
error output signal, and a PFSM (Pre-configurable Finite State Machine)
which manages the operational modes of the PMIC.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20231208114919.3429562-7-n-francis@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
This patch adds support for TPS6594 PMIC on wkup I2C0 bus. This device
provides regulators (bucks and LDOs), but also GPIOs, a RTC, a watchdog,
an ESM (Error Signal Monitor) which monitors the SoC error output
signal, and a PFSM (Pre-configurable Finite State Machine) which manages
the operational modes of the PMIC.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20231208114919.3429562-6-n-francis@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
This patch adds support for TPS6593 PMIC on wkup I2C0 bus.
This device provides regulators (bucks and LDOs), but also
GPIOs, a RTC, a watchdog, an ESM (Error Signal Monitor)
which monitors the SoC error output signal, and a PFSM
(Pre-configurable Finite State Machine) which manages the
operational modes of the PMIC.
Signed-off-by: Jerome Neanne <jneanne@baylibre.com>
Signed-off-by: Esteban Blanc <eblanc@baylibre.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20231208114919.3429562-5-n-francis@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
This patch adds support for TPS6594 PMIC family on wakup I2C0 bus.
Theses devices provides regulators (bucks and LDOs), but also
GPIOs, a RTC, a watchdog, an ESM (Error Signal Monitor)
which monitors the SoC error output signal, and a PFSM
(Pre-configurable Finite State Machine) which manages the
operational modes of the PMIC.
Signed-off-by: Jerome Neanne <jneanne@baylibre.com>
Signed-off-by: Esteban Blanc <eblanc@baylibre.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20231208114919.3429562-4-n-francis@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
This patch adds support for TPS6594 PMIC family on wakup I2C0 bus.
Theses devices provides regulators (bucks and LDOs), but also
GPIOs, a RTC, a watchdog, an ESM (Error Signal Monitor)
which monitors the SoC error output signal, and a PFSM
(Pre-configurable Finite State Machine) which manages the
operational modes of the PMIC.
Signed-off-by: Esteban Blanc <eblanc@baylibre.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20231208114919.3429562-3-n-francis@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
This patch adds support for TPS6594 PMIC family on wakup I2C0 bus.
Theses devices provides regulators (bucks and LDOs), but also
GPIOs, a RTC, a watchdog, an ESM (Error Signal Monitor)
which monitors the SoC error output signal, and a PFSM
(Pre-configurable Finite State Machine) which manages the
operational modes of the PMIC.
Signed-off-by: Esteban Blanc <eblanc@baylibre.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Reid Tonking <reidt@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20231208114919.3429562-2-n-francis@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Verdin SPI_1 interface has a dedicated hardware controlled chip select
that is currently configured in the same pinctrl group as MISO/MOSI/CLK,
however it is possible that it can be used only as a standard GPIO be it
a chip select or not.
To maximize flexibility and avoid duplication in the carrier board dts
files move the SPI_1 CS in a dedicated pinctrl and also adds an
additional pinctrl to simplify using SPI_1 CS as a GPIO.
Signed-off-by: Joao Paulo Goncalves <joao.goncalves@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://lore.kernel.org/r/20231205184605.35225-2-francesco@dolcini.it
Signed-off-by: Nishanth Menon <nm@ti.com>
The GPIO Expander has a line name defined as GPIO0_HDMI_RST. This line
is no longer associated with the HDMI Reset so we removed it.
Signed-off-by: Garrett Giordano <ggiordano@phytec.com>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20231204222811.2344460-3-ggiordano@phytec.com
Signed-off-by: Nishanth Menon <nm@ti.com>
The DSS outputs DPI signals via its second video port (VP2). The DPI
output from DSS is 24 bits (RGB888) and is forwarded to an HDMI
transmitter (SIL9022) on the board.
Add pinmux for DSS DPI output and HDMI Interrupt.
Add DT nodes for SIL9022 HDMI transmitter (TX), and the HDMI connector
on the phyBOARD-Lyra.
Additionally, connect the output of DSS (VP2) with input of the HDMI TX,
and the output of HDMI TX to the input of the HDMI connector.
Signed-off-by: Garrett Giordano <ggiordano@phytec.com>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20231204222811.2344460-2-ggiordano@phytec.com
Signed-off-by: Nishanth Menon <nm@ti.com>
The gpio-expander on i2c-1 has a maximum frequency of 100kHz. Update our
main_i2c1 frequency to allow the nxp,pcf8574 gpio-expander to function
properly.
Signed-off-by: Garrett Giordano <ggiordano@phytec.com>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20231204222811.2344460-1-ggiordano@phytec.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Communication between the R5F subsystem and Linux takes place using DMA
memory regions and mailboxes. Here we add DT nodes for the memory
regions and mailboxes to facilitate communication between the R5
clusters and Linux as remoteproc will fail to start if no memory
regions or mailboxes are provided.
Fixes: c48ac0efe6 ("arm64: dts: ti: Add support for phyBOARD-Electra-AM642")
Signed-off-by: Garrett Giordano <ggiordano@phytec.com>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20231204212304.1736306-1-ggiordano@phytec.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Combined dtb builds are only useful for making sure that the overlay
applies cleanly on the base dtb.
So we move all such combined blobs under a `dtb- +=` section that is
only built when CONFIG_OF_ALL_DTBS is enabled.
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20231201-csi_dts-v3-9-9f06f31080fe@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
RPi v2 Camera (IMX219) is an 8MP camera that can be used with SK-AM62A
through the 22-pin CSI-RX connector.
Same overlay can be used across SK-AM62* boards that have a 15/22-pin
FFC connector, so we name it with the k3-am62x- prefix.
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20231201-csi_dts-v3-8-9f06f31080fe@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Enable I2C-2 as it is used to control CSI based sensors. Also enable
IO-EXP-2 as it controls the mux between different CSI-2 connectors.
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20231201-csi_dts-v3-7-9f06f31080fe@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Three different OV5640 modules are supported using the 15-pin FFC
connector on SK-AM62:
- Digilent PCam 5C
- ALINX AN5641
- TEVI-OV5640-*-RPI
The Digilent and ALINX modules supply a 12Mhz XCLK to the sensor, while
the TEVI module supplies a 24Mhz XCLK, thus requiring a separate
overlay.
These overlays can be used on other boards of the SK-AM62* family that
have a 15/22-pin FFC connector, so we name the overlays with the prefix
k3-am62x-.
Tested-by: Martyn Welch <martyn.welch@collabora.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20231201-csi_dts-v3-6-9f06f31080fe@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
CSI cameras are controlled using I2C, on SK-AM62 and derivative boards
this is routed to I2C-2, so enable that bus.
Specific sensor connected to this bus will be described in the DT
overlay for each sensor.
Tested-by: Martyn Welch <martyn.welch@collabora.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20231201-csi_dts-v3-5-9f06f31080fe@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Three different OV5640 modules are supported using the FFC connector on
BeaglePlay:
- Digilent PCam 5C
- ALINX AN5641
- TEVI-OV5640-*-RPI
The Digilent and ALINX modules supply a 12Mhz XCLK to the sensor, while
the TEVI module supplies a 24Mhz XCLK, thus requiring a separate
overlay.
Reviewed-by: Andrew Davis <afd@ti.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20231201-csi_dts-v3-4-9f06f31080fe@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Add nodes for Cadence DPHY, CSI2RX and TI's pixel-grabbing wrapper.
AM62A uses a dedicated BCDMA instance for CSI-RX traffic, so enable
that as well.
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20231201-csi_dts-v3-3-9f06f31080fe@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
The CSI2RX subsystem can be used to capture video frames from CSI-2
cameras. Add nodes for the CSI core, SHIM layer, and the DPHY.
Tested-by: Martyn Welch <martyn.welch@collabora.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20231201-csi_dts-v3-2-9f06f31080fe@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
The AM652 is basically a AM654 but with 2 cores instead of 4. Add a
DTSI file for AM652 matching AM654 except this core difference.
This removes the need to remove the extra cores from AM654 manually
in DT files for boards that use the AM652 variant. Do that for the
IOT2050 boards here.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20231205162358.23904-1-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
The main_uart0 may not always be the console, but it will always be
the UART0 in MAIN domain. Name the pinmux node to match. This makes
it consistent with all other TI SoC based boards.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20231127193602.151499-1-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
The Hot Plug Detect (HPD) signal for the HDMI display travels from the
on-board HDMI connector, through the IO Expander 1, and finally to the
main_gpio1 GPIO 23, of the SoC.
Add interrupt information for the IO Expander 1 (exp1) along with the
relevant pinmux.
Signed-off-by: Aradhya Bhatia <a-bhatia1@ti.com>
Reviewed-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20231108191652.1118155-1-a-bhatia1@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Enable UART2 for AM62 based SOM's Verdin carrier boards Dahlia,
Development and Yavia.
Earlier Verdin UART2 was reserved by R5 DM firmware which can be now
configured using boardcfg during U-boot compilation. In a default
config, no one writes to this UART.
Signed-off-by: Parth Pancholi <parth.pancholi@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://lore.kernel.org/r/20231121160436.1032364-1-parth105105@gmail.com
Signed-off-by: Nishanth Menon <nm@ti.com>
On the AM62 platform we have no single 1:1 relation regarding index of
gpio and pin controller. Actually there are some linear ranges with
small holes inbetween. These ranges can be represented with the
gpio-ranges device tree property. They have been extracted manually
from the AM62x datasheet (Table 6-1. Pin Attributes).
Signed-off-by: Ronald Wahl <ronald.wahl@raritan.com>
Link: https://lore.kernel.org/r/20231127112657.2692103-1-rwahl@gmx.de
Signed-off-by: Nishanth Menon <nm@ti.com>
SDHCI nodes defined in the top-level AM64 SoC dtsi files are incomplete
and will not be functional unless they are extended.
As the attached SD/eMMC is only known about at the board integration level,
these nodes should only be enabled when provided with this information.
Disable the SDHCI nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20231117163339.89952-2-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
SDHCI nodes defined in the top-level AM65 SoC dtsi files are incomplete
and will not be functional unless they are extended.
As the attached SD/eMMC is only known about at the board integration level,
these nodes should only be enabled when provided with this information.
Disable the SDHCI nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20231117163339.89952-1-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
This matches the binding for this register region which fixes a couple
DTS check warnings.
While here trim the leading 0s from the "reg" definition.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Aradhya Bhatia <a-bhatia1@ti.com>
Link: https://lore.kernel.org/r/20231117141433.9461-1-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Like in other K3 SoCs the chipid register is inside the wakeup
configuration space. Move the chipid node under a new bus to
better represent this topology and match other similar SoCs.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20231117140910.8747-2-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Like in other K3 SoCs the chipid register is inside the wakeup
configuration space. Move the chipid node under a new bus to
better represent this topology and match other similar SoCs.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20231117140910.8747-3-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Like in other K3 SoCs the chipid register is inside the wakeup
configuration space. Move the chipid node under a new bus to
better represent this topology and match other similar SoCs.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20231117140910.8747-5-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Like in other K3 SoCs the chipid register is inside the wakeup
configuration space. Move the chipid node under a new bus to
better represent this topology and match other similar SoCs.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20231117140910.8747-1-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Like in other K3 SoCs the chipid register is inside the wakeup
configuration space. Move the chipid node under a new bus to
better represent this topology and match other similar SoCs.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20231117140910.8747-4-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Add alias for the MCU CPSW2G port to enable Linux to fetch MAC Address
for the port directly from U-Boot.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Link: https://lore.kernel.org/r/20231115085913.3585740-1-s-vadapalli@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Add multiple device tree nodes in order to support
runtime pinmuxing via debugfs.
All nodes are added to the pinctrl device node,
since they are now belonging to multiple interfaces now.
Note: Pinconf is also handled by debugfs-pinmux. This is possible since
pinconf and pinmux accessing the same 32-Bit register and setting the
function mask to 32-Bit allows writes to the whole register.
Signed-off-by: Benedikt Niedermayr <benedikt.niedermayr@siemens.com>
[Jan: fix node name style]
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Link: https://lore.kernel.org/r/3f90f3e521758622aa9b10f030cf0de1e68e77a4.1699087938.git.jan.kiszka@siemens.com
Signed-off-by: Nishanth Menon <nm@ti.com>
DSS irq trigger type is set to IRQ_TYPE_EDGE_RISING in the DT file, but
the TRM says it is level triggered.
For some reason triggering on rising edge results in double the amount
of expected interrupts, e.g. for normal page flipping test the number of
interrupts per second is 2 * fps. It is as if the IRQ triggers on both
edges. There are no other side effects to this issue than slightly
increased CPU & power consumption due to the extra interrupt.
Switching to IRQ_TYPE_LEVEL_HIGH is correct and fixes the issue, so
let's do that.
Fixes: fc539b90ed ("arm64: dts: ti: am654: Add DSS node")
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Aradhya Bhatia <a-bhatia1@ti.com>
Link: https://lore.kernel.org/r/20231106-am65-dss-clk-edge-v1-1-4a959fec0e1e@ideasonboard.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Here is the big set of char/misc and other small driver subsystem
changes for 6.7-rc1. Included in here are:
- IIO subsystem driver updates and additions (largest part of this
pull request)
- FPGA subsystem driver updates
- Counter subsystem driver updates
- ICC subsystem driver updates
- extcon subsystem driver updates
- mei driver updates and additions
- nvmem subsystem driver updates and additions
- comedi subsystem dependency fixes
- parport driver fixups
- cdx subsystem driver and core updates
- splice support for /dev/zero and /dev/full
- other smaller driver cleanups
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZUTSzg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylH3QCfbZuG8MiglEZUd4slRLUNqcRQ5tQAn1yKpDFo
l3KLkxo1UTLMXbJBWe+b
=gafK
-----END PGP SIGNATURE-----
Merge tag 'char-misc-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc updates from Greg KH:
"Here is the big set of char/misc and other small driver subsystem
changes for 6.7-rc1. Included in here are:
- IIO subsystem driver updates and additions (largest part of this
pull request)
- FPGA subsystem driver updates
- Counter subsystem driver updates
- ICC subsystem driver updates
- extcon subsystem driver updates
- mei driver updates and additions
- nvmem subsystem driver updates and additions
- comedi subsystem dependency fixes
- parport driver fixups
- cdx subsystem driver and core updates
- splice support for /dev/zero and /dev/full
- other smaller driver cleanups
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (326 commits)
cdx: add sysfs for subsystem, class and revision
cdx: add sysfs for bus reset
cdx: add support for bus enable and disable
cdx: Register cdx bus as a device on cdx subsystem
cdx: Create symbol namespaces for cdx subsystem
cdx: Introduce lock to protect controller ops
cdx: Remove cdx controller list from cdx bus system
dts: ti: k3-am625-beagleplay: Add beaglecc1352
greybus: Add BeaglePlay Linux Driver
dt-bindings: net: Add ti,cc1352p7
dt-bindings: eeprom: at24: allow NVMEM cells based on old syntax
dt-bindings: nvmem: SID: allow NVMEM cells based on old syntax
Revert "nvmem: add new config option"
MAINTAINERS: coresight: Add missing Coresight files
misc: pci_endpoint_test: Add deviceID for J721S2 PCIe EP device support
firmware: xilinx: Move EXPORT_SYMBOL_GPL next to zynqmp_pm_feature definition
uacce: make uacce_class constant
ocxl: make ocxl_class constant
cxl: make cxl_class constant
misc: phantom: make phantom_class constant
...
The BeaglePlay board by BeagleBoard.org has a CC1352P7 co-processor
connected to the main AM62 (running Linux) over UART. In the BeagleConnect
Technology, CC1352 is responsible for handling 6LoWPAN communication with
beagleconnect freedom nodes as well as their discovery.
This mcu is used by gb-beagleplay, a Greybus driver for BeaglePlay.
Signed-off-by: Ayush Singh <ayushdevel1325@gmail.com>
Link: https://lore.kernel.org/r/20231017101116.178041-4-ayushdevel1325@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The IDK application board has 4 Gigabit Ethernet ports.
This patch adds support for the 4 Gigabit Ethernet ports
which are provided by ICSSG0 and ICSSG1.
The IEP0 SYNC_OUT0 pins are used for PPS out on the IDK card.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Link: https://lore.kernel.org/r/20231020051937.3709871-4-danishanwar@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The ICSSG IP on AM65x SoCs have two Industrial Ethernet Peripherals (IEPs)
to manage/generate Industrial Ethernet functions such as time stamping.
Each IEP sub-module is sourced from an internal clock mux that can be
sourced from either of the IP instance's ICSSG_IEP_GCLK or ICSSG_ICLK.
Add the IEP nodes for all the ICSSG instances.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Link: https://lore.kernel.org/r/20231020051937.3709871-2-danishanwar@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Update the am62p5-sk board file to enable the new IPs introduced
in the SoC dtb.
Signed-off-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20231019223055.1574125-6-bb@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The am62px shares many of the same IP as the existing am62x family
of SoCs, Introduce more nodes for hardware available on the am62p5.
Signed-off-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20231019223055.1574125-5-bb@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
AM69 starter kit features an HDMI port and an eDP port.
Add assigned clocks for DSS, DT node for DisplayPort PHY,
pinmux for HDMI hotplug and power down, mcu_i2c1 and dss_vout
for HDMI.
Also enable Serdes4 settings for DP display.
Add the endpoint nodes to describe connection from:
DSS => MHDP => DisplayPort connector
DSS => TI TFP410 DPI-to-DVI Bridge => HDMI connector
Signed-off-by: Dasnavis Sabiya <sabiya.d@ti.com>
[j-choudhary@ti.com: Fix dvi-bridge, dss, mhdp and serdes-refclk]
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Reviewed-by: Aradhya Bhatia <a-bhatia1@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20231019054022.175163-6-j-choudhary@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Enable display for J784S4 EVM.
Add assigned clocks for DSS, DT node for DisplayPort PHY and pinmux for
DP HPD. Add the clock frequency for serdes_refclk.
Add the endpoint nodes to describe connection from:
DSS => MHDP => DisplayPort connector.
Also add the GPIO expander-4 node and pinmux for main_i2c4 which is
required for controlling DP power. Set status for all required nodes
for DP-0 as "okay".
Signed-off-by: Rahul T R <r-ravikumar@ti.com>
[j-choudhary@ti.com: move all the changes together to enable DP-0 in EVM]
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Reviewed-by: Aradhya Bhatia <a-bhatia1@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20231019054022.175163-5-j-choudhary@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add DSS and DP-bridge node for J784S4 SoC. DSS IP in J784S4 is
same as DSS IP in J721E, so same compatible is being used.
The DP is Cadence MHDP8546.
Disable them by default as nodes are missing port definition
and phy link configurations which are added later in platform
dt file.
Signed-off-by: Rahul T R <r-ravikumar@ti.com>
[j-choudhary@ti.com: move dss & mhdp node together in main, fix dss node]
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Reviewed-by: Aradhya Bhatia <a-bhatia1@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20231019054022.175163-4-j-choudhary@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
J784S4 SoC has 4 Serdes instances along with their respective WIZ
instances. Add device-tree nodes for them and disable them by default
as the node is incomplete and phy link properties will be added in
the platform dt file.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
[j-choudhary@ti.com: fix serdes_wiz clock order & disable serdes refclk]
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20231019054022.175163-3-j-choudhary@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The system controller node manages the CTRL_MMR0 region.
Add serdes_ln_ctrl node which is used for controlling the SERDES lane mux.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
[j-choudhary@ti.com: Fix serdes_ln_ctrl node]
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20231019054022.175163-2-j-choudhary@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
There are totally 2 instances of watchdog module in MCU domain.
These instances are coupled with the MCU domain R5F instances.
Reserving them as they are not used by A72.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Link: https://lore.kernel.org/r/20231008044657.25788-8-j-keerthy@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
There are totally 9 instances of watchdog module. One each for the
2 A72 cores, one each for the 2 C7x cores, 1 for the GPU, 1 each
for the 4 R5F cores in the main domain. Keeping only the A72 instances
enabled and reserving the rest by default as they will be used by
their respective firmware.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Link: https://lore.kernel.org/r/20231008044657.25788-7-j-keerthy@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
There are totally 2 instances of watchdog module in MCU domain.
These instances are coupled with the MCU domain R5F instances.
Disabling them as they are not used by Linux.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Link: https://lore.kernel.org/r/20231008044657.25788-6-j-keerthy@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
There are totally 19 instances of watchdog module. One each for the
8 A72 cores, one each for the 4 C7x cores, 1 for the GPU, 1 each
for the 6 R5F cores in the main domain. The non-A72 instances are
coupled with the R5Fs, C7x & GPU instances. Keeping them as reserved as
they are not used by A72.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Link: https://lore.kernel.org/r/20231008044657.25788-5-j-keerthy@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Patch adds the ESM instances for J784s4. It has 3 instances.
One in the main domain and two in the mcu-wakeup domain.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Link: https://lore.kernel.org/r/20231008044657.25788-3-j-keerthy@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Patch adds the ESM instances for J721s2. It has 3 instances.
One in the main domain and two in the mcu-wakeup domain.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Link: https://lore.kernel.org/r/20231008044657.25788-2-j-keerthy@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
J784S4 has a dedicated BCDMA controller for the Camera Serial Interface.
Events from the BCDMA controller instance are routed through the
main UDMA interrupt aggregator as unmapped events. Add the node for
the DMA controller and keep it disabled by default.
See J784S4 Technical Reference Manual (SPRUJ52)
for further details: http://www.ti.com/lit/zip/spruj52
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Reviewed-by: Jayesh Choudhary <j-choudhary@ti.com>
Link: https://lore.kernel.org/r/20231010111723.17524-3-vaishnav.a@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
J721S2 has a dedicated BCDMA controller for the Camera Serial Interface.
Events from the BCDMA controller instance are routed through the
main UDMA interrupt aggregator as unmapped events. Add the node for
the DMA controller and keep it disabled by default.
See J721S2 Technical Reference Manual (SPRUJ28)
for further details: http://www.ti.com/lit/pdf/spruj28
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Reviewed-by: Jayesh Choudhary <j-choudhary@ti.com>
Link: https://lore.kernel.org/r/20231010111723.17524-2-vaishnav.a@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
"simple-mfd" as standalone compatible is frowned upon, so model main and
MCU NAVSS (Navigator SubSystem) nodes as simple-bus as there is really
no need for these nodes to be MFD.
Link: https://lore.kernel.org/r/20231005151302.1290363-3-vigneshr@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
"simple-mfd" as standalone compatible is frowned upon, so model DMSS
(Data Movement Subsystem) node as simple-bus as there is really no need
for these nodes to be MFD.
Link: https://lore.kernel.org/r/20231005151302.1290363-2-vigneshr@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
This patch adds support for TPS6593 PMIC on main I2C0 bus.
This device provides regulators (bucks and LDOs), but also
GPIOs, a RTC, a watchdog, an ESM (Error Signal Monitor)
which monitors the SoC error output signal, and a PFSM
(Pre-configurable Finite State Machine) which manages the
operational modes of the PMIC.
Signed-off-by: Julien Panis <jpanis@baylibre.com>
Signed-off-by: Esteban Blanc <eblanc@baylibre.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20231003-mcasp_am62a-v3-4-2b631ff319ca@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The TLV320AIC3106 audio codec is interfaced on the i2c-1 bus. With the
default rate of 400Khz the i2c register writes fail to sync:
[ 36.026387] tlv320aic3x 1-001b: Unable to sync registers 0x16-0x16. -110
[ 38.101130] omap_i2c 20010000.i2c: controller timed out
Dropping the rate to 100Khz fixes the issue.
Fixes: 38c4a08c82 ("arm64: dts: ti: Add support for AM62A7-SK")
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Aradhya Bhatia <a-bhatia1@ti.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20231003-mcasp_am62a-v3-3-2b631ff319ca@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Same as AM62, AM62A has three instances of McASP which can be used for
transmitting or receiving digital audio in various formats.
Reviewed-by: Jayesh Choudhary <j-choudhary@ti.com>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20231003-mcasp_am62a-v3-1-2b631ff319ca@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The pin headers X41 and X42 do not have a fixed function. All of these
pins can be assigned to PRG0, but as a default, it makes more sense to
configure them as simple GPIOs, as the MBaX4XxL is a starterkit/evaluation
mainboard.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/77c30081154774ce31fc4306474a3afa52b07753.1695901360.git.matthias.schiffer@ew.tq-group.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Describes the hardware better, and avoids a few warnings during boot:
lm75 0-004a: supply vs not found, using dummy regulator
at24 0-0050: supply vcc not found, using dummy regulator
at24 0-0054: supply vcc not found, using dummy regulator
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/d5991041263c96c798b94c0844a1550e28daa3b1.1695901360.git.matthias.schiffer@ew.tq-group.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
AM68 Starter kit has a USB3 hub that connects to the SerDes0 Lane 2.
Update the SerDes configuration to support USB3.
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Link: https://lore.kernel.org/r/20230921100039.19897-4-r-gunasekaran@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
