In AM69 SoC there are 4 instances of the 4 lane SERDES. So in
"serdes_ln_ctrl" node there are total 16 entries in "mux-reg-mask"
property. But "idle-states" is defined only for the lanes of first two
SERDES instances. SERDES lane mapping is left at its reset state of
"zero" for all four lanes of SERDES2 and SERDES4. The reset state of
"zero" corresponds to the following configuration:
Lanes 0 and 1 of SERDES2 are unused
CPSW MAC Ports 1 and 2 mapped to lanes 2 and 3 of SERDES2
EDP Lanes 0, 1, 2 and 3 mapped to lanes 0, 1, 2 and 3 of SERDES4
For completeness, define the "idle-states" for the lanes of remaining
SERDES instances.
Signed-off-by: Hrushikesh Salunke <h-salunke@ti.com>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://lore.kernel.org/r/20250708113942.4137917-1-h-salunke@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The 'bootph-all' tag was added to the dt-schema to describe the various
nodes used during the different phases of bootup with DT. Add the
bootph-all tag to all nodes that are used during the early stages of
bootup by the bootloaders.
This includes the console UART along with the SD and eMMC nodes and its
required regulators for the 3v3 to 1v8 transition and the various nodes
for Ethernet booting.
Signed-off-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20250710-62a-uboot-cleanup-v2-1-9e04a7db1f54@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The 'bootph-all' tag was added to the dt-schema to describe the various
nodes used during the different phases of bootup with DT. Add the
bootph-all tag to all nodes that are used in the bootloader for the
AM654 reference board.
UARTs used as a console, the SD and eMMC nodes along with the needed
regulators for UHS modes, and the needed nodes for OSPI boot are all
marked with 'bootph-all' to handle the various boot modes the board is
capable of
Signed-off-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20250710-65-boot-phases-v2-2-d431deb88783@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The 'bootph-all' tag was added to the dt-schema to describe the various
nodes used during the different phases of bootup with DT. Add the
bootph-all tag to all required nodes for all AM65x platforms.
Mark the mailbox and ring accelerators needed to communicate the with
various vendor firmware and the power, clock and reset nodes along with
the MMR for the chip-id to facilitate detecting the SoC and which
silicon version during the early stages of bootup with 'bootph-all' as
they are used during all phases of bootup
--
Changes in v2:
- removed tag from &mcu_udmap{} node
Signed-off-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20250710-65-boot-phases-v2-1-d431deb88783@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
AM62D-EVM evaluation module (EVM) is a low-cost expandable platform board
designed for AM62D2 SoC from TI. It supports the following interfaces:
* 4 GB LPDDR4 RAM
* x2 Gigabit Ethernet expansion connectors
* x4 3.5mm TRS Audio Jack Line In
* x4 3.5mm TRS Audio Jack Line Out
* x2 Audio expansion connectors
* x1 Type-A USB 2.0, x1 Type-C dual-role device (DRD) USB 2.0
* x1 UHS-1 capable micro SD card slot
* 32 GB eMMC Flash
* 512 Mb OSPI NOR flash
* x4 UARTs via USB 2.0-B
* XDS110 for onboard JTAG debug using USB
* Temperature sensors, user push buttons and LEDs
Although AM62D2 and AM62A7 differ in peripheral capabilities example
multimedia, VPAC, and display subsystems, the core architecture remains
same. To reduce duplication, AM62D support reuses the AM62A dtsi and the
necessary overrides will be handled in SOC specific dtsi file and a
board specific dts.
Add basic support for AM62D2-EVM.
Schematics Link - https://www.ti.com/lit/zip/sprcal5
Signed-off-by: Paresh Bhagat <p-bhagat@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Andrew Davis <afd@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20250708085839.1498505-5-p-bhagat@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add bootph property directly into the original definitions of relevant
nodes (e.g., power domains, USB controllers, and other peripherals)
within their respective DTSI files (ex. main, mcu, and wakeup) for
am62a.
By defining bootph in the nodes source definitions instead of appending
it later in final DTS files, this change ensures that the property is
inherently present wherever the nodes are reused across derived device
trees.
Signed-off-by: Paresh Bhagat <p-bhagat@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20250708085839.1498505-2-p-bhagat@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
While the TI AM62P supports a junction temperature (Tj) of up to 125°C
for industrial and automotive parts, Toradex Verdin-AM62P hardware
lifetime guarantees consider a 105°C Tj. Change the passive trip points
to 95°C and the critical trip points to 105°C to be compliant with the
hardware specifications.
Signed-off-by: João Paulo Gonçalves <joao.goncalves@toradex.com>
Link: https://lore.kernel.org/r/20250623-b4-verdin-am62p-cooling-device-v1-2-cc185ba5843d@toradex.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add DT node for PBIST_14 that is responsible for triggering the PBIST
self-tests for the MAIN_R5_2_x cores.
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Link: https://lore.kernel.org/r/20250605063506.2005637-3-n-francis@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
This moves pinmux child nodes for sdhci0 node from k3-am62x-sk-common
to each top level board file. This is needed since we require internal
pullups for AM62x SK and not for AM62 LP SK since it has external
pullups on DATA 1-7.
Internal pulls are required for AM62 SK as per JESD84 spec
recommendation to prevent unconnected lines floating.
Fixes: d19a66ae48 ("arm64: dts: ti: k3-am625-sk: Enable on board peripherals")
Cc: stable@vger.kernel.org
Signed-off-by: Judith Mendez <jm@ti.com>
Link: https://lore.kernel.org/r/20250707190830.3951619-1-jm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
main_uart1 reserved for TIFS firmware traces is routed to the
onboard FT4232 via a FET switch which is connected to pin A21 and
B21 of the SoC and not E17 and C17. Fix it.
Fixes: cf39ff15cc ("arm64: dts: ti: k3-am62a7-sk: Describe main_uart1 and wkup_uart")
Cc: stable@vger.kernel.org
Signed-off-by: Hong Guan <hguan@ti.com>
[bb@ti.com: expanded commit message]
Signed-off-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20250707-uart-fixes-v1-1-8164147218b0@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Allow overlays to be applied to any DTB without manually enabling it
for each file. This adds around ~10% to the total size of the DTB files
on average.
Signed-off-by: Andrew Davis <afd@ti.com>
Acked-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20250702145314.71996-1-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
PWM_3_DSI is used as the HDMI Hot-Plug Detect (HPD) GPIO for the Verdin
DSI-to-HDMI adapter. After the commit 33bab9d84e ("arm64: dts: ti:
k3-am62p: fix pinctrl settings"), the pin was incorrectly set as output
without RXACTIVE, breaking HPD detection and display functionality.
The issue was previously hidden and worked by chance before the mentioned
pinctrl fix.
Fix the pinmux configuration to correctly set PWM_3_DSI GPIO as an input.
Fixes: 87f95ea316 ("arm64: dts: ti: Add Toradex Verdin AM62P")
Signed-off-by: Parth Pancholi <parth.pancholi@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://lore.kernel.org/r/20250703084534.1649594-1-parth105105@gmail.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Switch Schmitt Trigger functions for PIN_INPUT* macros by default. This is
HW PoR configuration, the slew rate requirements without ST enabled are
pretty tough for these devices. We've noticed spurious GPIO interrupts even
with noise-free edges but not meeting slew rate requirements (3.3E+6 V/s
for 3.3v LVCMOS).
It's not obvious why one might want to disable the PoR-enabled ST on any
pin. Just enable it by default. As it's not possible to provide OR-able
macros to disable the ST, shall anyone require it, provide a set of
new macros with _NOST suffix.
Fixes: fe49f2d776 ("arm64: dts: ti: Use local header for pinctrl register values")
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Link: https://lore.kernel.org/r/20250701105437.3539924-1-alexander.sverdlin@siemens.com
[vigneshr@ti.com: Add Fixes tag]
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add internal pull-up to the SD_1 card detect signal, without this the CD
signal is floating and spurious detects events can happen.
Fixes: 87f95ea316 ("arm64: dts: ti: Add Toradex Verdin AM62P")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://lore.kernel.org/r/20250701081643.71406-1-francesco@dolcini.it
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The ACSPCIE1 module on TI's J784S4 SoC is capable of driving the reference
clock required by the PCIe Endpoint device. It is an alternative to on-
board and external reference clock generators.
Add the device-tree node for the same.
Signed-off-by: Parth Pancholi <parth.pancholi@toradex.com>
Link: https://lore.kernel.org/r/20250513152155.1590689-1-parth105105@gmail.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
According to the "GPIO Expander Map / Table" section of the J722S EVM
Schematic within the Evaluation Module Design Files package [0], the
GPIO Pin P05 located on the GPIO Expander 1 (I2C0/0x23) has to be pulled
down to select the Type-C interface. Since commit under Fixes claims to
enable the Type-C interface, update the property within "p05-hog" from
"output-high" to "output-low", thereby switching from the Type-A
interface to the Type-C interface.
[0]: https://www.ti.com/lit/zip/sprr495
Cc: stable@vger.kernel.org
Fixes: 485705df5d ("arm64: dts: ti: k3-j722s: Enable PCIe and USB support on J722S-EVM")
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://lore.kernel.org/r/20250623100657.4082031-1-s-vadapalli@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
AM64X SoC has one instance of PCIe which is PCIe0. To support PCIe boot
on AM64X SoC, PCIe0 needs to be in endpoint mode and it needs to be
functional at all stages of PCIe boot process. Thus add the
"bootph-all" boot phase tag to "pcie0_ep" device tree node.
Signed-off-by: Hrushikesh Salunke <h-salunke@ti.com>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://lore.kernel.org/r/20250610054920.2395509-1-h-salunke@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Pinmux registers ends at 0x000f42ac (including). Thus, the size argument
of the pinctrl-single node has to be 0x2b0. Fix it.
This will fix the following error:
pinctrl-single f4000.pinctrl: mux offset out of range: 0x2ac (0x2ac)
Fixes: 29075cc09f ("arm64: dts: ti: Introduce AM62P5 family of SoCs")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Link: https://lore.kernel.org/r/20250618065239.1904953-1-mwalle@kernel.org
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Describe the octal SPI NAND available on the low-power starter kit.
The pinctrl configuration comes from TI fork.
With the current mainline tree, we currently get the following
performances:
eraseblock write speed is 7507 KiB/s
eraseblock read speed is 15802 KiB/s
page write speed is 7551 KiB/s
page read speed is 15609 KiB/s
2 page write speed is 7551 KiB/s
2 page read speed is 15609 KiB/s
erase speed is 284444 KiB/s
2x multi-block erase speed is 512000 KiB/s
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20250613182356.1272642-1-miquel.raynal@bootlin.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add McASP 0-4 instances and keep them disabled because several
required properties are missing as they are board specific.
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Link: https://lore.kernel.org/r/20250604104656.38752-2-j-choudhary@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Enable internal bias pull-ups on the SoC-side I2C_3_HDMI that do not have
external pull resistors populated on the SoM. This ensures proper
default line levels.
Fixes: 87f95ea316 ("arm64: dts: ti: Add Toradex Verdin AM62P")
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://lore.kernel.org/r/20250529102601.452859-1-ghidoliemanuele@gmail.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Enable internal bias pull-ups on the SoC-side I2C buses that do not have
external pull resistors populated on the SoM. This ensures proper
default line levels.
Cc: stable@vger.kernel.org
Fixes: 316b80246b ("arm64: dts: ti: add verdin am62")
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://lore.kernel.org/r/20250528110741.262336-1-ghidoliemanuele@gmail.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
For the ICSSG PHYs to operate correctly, a 25 MHz reference clock must
be supplied on CLKOUT0. Previously, our bootloader configured this
clock, which is why the PRU Ethernet ports appeared to work, but the
change never made it into the device tree.
Add clock properties to make EXT_REFCLK1.CLKOUT0 output a 25MHz clock.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Fixes: 87adfd1ab0 ("arm64: dts: ti: am642-phyboard-electra: Add PRU-ICSSG nodes")
Link: https://lore.kernel.org/r/20250521053339.1751844-1-w.egorov@phytec.de
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
TechNexion TEVI OV5640 camera is a 5MP camera that can be used with
J722S EVM through the 22-pin CSI-RX connector. Add a reference overlay
for quad TEVI OV5640 modules on J722S EVM.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Signed-off-by: Yemike Abhilash Chandra <y-abhilashchandra@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20250509091911.2442934-5-y-abhilashchandra@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
RPi v2 Camera (IMX219) is an 8MP camera that can be used with J722S EVM
through the 22-pin CSI-RX connector. Add a reference overlay for quad
IMX219 RPI camera v2 modules on J722S EVM
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Signed-off-by: Yemike Abhilash Chandra <y-abhilashchandra@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20250509091911.2442934-4-y-abhilashchandra@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
J722S EVM has the CSI2RX routed to a MIPI CSI connector and to 22-pin RPi
camera connector through an analog mux with GPIO control, model mux so
that an overlay can control the mux state according to connected cameras.
Signed-off-by: Yemike Abhilash Chandra <y-abhilashchandra@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20250509091911.2442934-3-y-abhilashchandra@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Add device tree nodes for two regulators on the J722S-EVM. VSYS_3V3 is the
output of LM5141-Q1, and it serves as an input to TPS22990 which produces
VSYS_3V3_EXP [1]. VSYS_3V3_EXP serves as vin-supply to CSI RPI Connectors.
Signed-off-by: Yemike Abhilash Chandra <y-abhilashchandra@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
[1]: https://www.ti.com/lit/zip/sprr495
Link: https://lore.kernel.org/r/20250509091911.2442934-2-y-abhilashchandra@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
The main rti4 watchdog timer is used by the C7x DSP, so reserve the
timer in the linux device tree.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Reviewed-by: Judith Mendez <jm@ti.com>
Link: https://lore.kernel.org/r/20250507070008.1231611-4-d.schultz@phytec.de
Signed-off-by: Nishanth Menon <nm@ti.com>
For every remote processor, set up dedicated memory regions and
associate the required mailbox channels. Allocate two memory areas
per remote core: one 1MB region for vring shared buffers, and
another for external memory used by the remote processor for its
resource table and trace buffer.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Reviewed-by: Andrew Davis <afd@ti.com>
Reviewed-by: Judith Mendez <jm@ti.com>
Link: https://lore.kernel.org/r/20250507070008.1231611-3-d.schultz@phytec.de
Signed-off-by: Nishanth Menon <nm@ti.com>
For every remote processor, set up dedicated memory regions and
associate the required mailbox channels. Allocate two memory areas
per remote core: one 1MB region for vring shared buffers, and
another for external memory used by the remote processor for its
resource table and trace buffer.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Andrew Davis <afd@ti.com>
Reviewed-by: Judith Mendez <jm@ti.com>
Link: https://lore.kernel.org/r/20250507070008.1231611-2-d.schultz@phytec.de
Signed-off-by: Nishanth Menon <nm@ti.com>
Rename 'main0_thermal_trip0' to a more descriptive name that
includes 'fan', as the current name is too generic for a fan control
trip point.
Move the fan to a new cooling map to avoid overwriting the passive
trip point used for CPU frequency throttling when this overlay is
enabled. Also, add the fan to the existing cooling map.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20250506114134.3514899-2-d.schultz@phytec.de
Signed-off-by: Nishanth Menon <nm@ti.com>
Enable throttling down the CPU frequency when an alert temperature
threshold (lower than the critical threshold) is reached.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20250506114134.3514899-1-d.schultz@phytec.de
Signed-off-by: Nishanth Menon <nm@ti.com>
Use the new compatible string and power domain name as introduced in
commit 2c01d90998 ("dt-bindings: gpu: img: Future-proofing
enhancements").
Reviewed-by: Randolph Sapp <rs@ti.com>
Signed-off-by: Matt Coster <matt.coster@imgtec.com>
Link: https://lore.kernel.org/r/20250428-bxs-4-64-dts-v4-1-eddafb4ae19f@imgtec.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Add the DT node for the PRUSS-M processor subsystem that is present
on the K3 AM62x SoCs. The K3 AM62x family of SoC has one PRUSS-M
instance and it has two Programmable Real-Time Units (PRU0 and PRU1).
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
[ Judith: Fix pruss_iclk id for pruss_coreclk_mux ]
Signed-off-by: Judith Mendez <jm@ti.com>
Tested-by: Daniel Schultz <d.schultz@phytec.de>
Reviewed-by: Beleswar Padhi <b-padhi@ti.com>
Acked-by: Hari Nagalla <hnagalla@ti.com>
Link: https://lore.kernel.org/r/20250430144343.972234-1-jm@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
AM64x device has 4 R5F cores in the main domain. TI MCU firmware uses
main domain timers as tick timers in these firmwares. Hence keep them
as reserved in the Linux device tree.
Signed-off-by: Hari Nagalla <hnagalla@ti.com>
Signed-off-by: Judith Mendez <jm@ti.com>
Reviewed-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20250502220325.3230653-12-jm@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
The main rti4 watchdog timer is used by the C7x DSP, so reserve the
timer in the linux device tree.
Signed-off-by: Hari Nagalla <hnagalla@ti.com>
Signed-off-by: Judith Mendez <jm@ti.com>
Reviewed-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20250502220325.3230653-11-jm@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
C7x DSP uses main_timer2, so mark it as reserved in linux DT.
Signed-off-by: Hari Nagalla <hnagalla@ti.com>
Signed-off-by: Judith Mendez <jm@ti.com>
Reviewed-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20250502220325.3230653-10-jm@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
For each remote proc, reserve memory for IPC and bind the mailbox
assignments. Two memory regions are reserved for each remote processor.
The first region of 1MB of memory is used for Vring shared buffers
and the second region is used as external memory to the remote processor
for the resource table and for tracebuffer allocations.
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Signed-off-by: Hari Nagalla <hnagalla@ti.com>
Signed-off-by: Judith Mendez <jm@ti.com>
Acked-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20250502220325.3230653-9-jm@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
For each remote proc, reserve memory for IPC and bind the mailbox
assignments. Two memory regions are reserved for each remote processor.
The first region of 1MB of memory is used for Vring shared buffers
and the second region is used as external memory to the remote processor
for the resource table and for tracebuffer allocations.
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Signed-off-by: Hari Nagalla <hnagalla@ti.com>
Signed-off-by: Judith Mendez <jm@ti.com>
Reviewed-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20250502220325.3230653-8-jm@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
