This test establishes a binding between nbma ip of a spoke and its
protocol address. This information is pushed to hub.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Just another round of trying to add pytest.mark.bgpd. Not finished yet just
what I could stand doing for a few minutes.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Fixes:
/usr/lib/python3.9/site-packages/_pytest/config/__init__.py:1463: in getoption
val = getattr(self.option, name)
E AttributeError: 'Namespace' object has no attribute 'topology_only'
The above exception was the direct cause of the following exception:
/usr/lib/python3.9/site-packages/pluggy/manager.py:127: in register
hook._maybe_apply_history(hookimpl)
/usr/lib/python3.9/site-packages/pluggy/hooks.py:333: in _maybe_apply_history
res = self._hookexec(self, [method], kwargs)
/usr/lib/python3.9/site-packages/pluggy/manager.py:93: in _hookexec
return self._inner_hookexec(hook, methods, kwargs)
/usr/lib/python3.9/site-packages/pluggy/manager.py:84: in <lambda>
self._inner_hookexec = lambda hook, methods, kwargs: hook.multicall(
tests/topotests/conftest.py:62: in pytest_configure
if config.getoption("--topology-only"):
/usr/lib/python3.9/site-packages/_pytest/config/__init__.py:1474: in getoption
raise ValueError(f"no option named {name!r}") from e
E ValueError: no option named 'topology_only'
Signed-off-by: Quentin Young <qlyoung@nvidia.com>
Description:
BGP session not established for ipv6 link local address with vrf config
Problem Description/Summary :
BGP session not established for ipv6 link local address with vrf configyy
1.Configure ipv6 link-local address fe80::1234/64 on dut1 and fe80::4567/64 on dut2
2.Configure BGP neighbors for ipv6 link-local on both dut1 and dut2
3.Verify BGP session is UP over link-local ipv6 address
4.Observed that bgp session not established for ipv6 link local address
Expected Behavior :
BGP session should be established for ipv6 link local address with vrf config
Signed-off-by: sudhanshukumar22 <sudhanshu.kumar@broadcom.com>
These are for string quoting (`%pSQ`) and string escaping (`%pSE`); the
sets / escape methods are currently rather "basic" and might be extended
in the future.
Signed-off-by: David Lamparter <equinox@diac24.net>
Analogous to Linux kernel `%pV` (but our mechanism expects 2 specifier
chars and `%pVA` is clearer anyway.)
Signed-off-by: David Lamparter <equinox@diac24.net>
... to suppress the warnings when using something that isn't quite ISO C
compatible and would otherwise cause compiler warnings from `-Wformat`.
Signed-off-by: David Lamparter <equinox@diac24.net>
Three new tests:
- OSPFv3 convergence using 'ipv6 ospf6 neighbor json'
- Default route functionality:
* Check that the LSA is present
* Check that the route was installed
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
This replaces `%n` with a safe, out-of-band option that simply records
the start and end offset of the output produced for each `%...`
specifier.
The old `%n` code is removed.
Signed-off-by: David Lamparter <equinox@diac24.net>
Allowing printfrr extensions to directly write to the output buffer has
a few advantages:
- there is no arbitrary length limit imposed (previously 64)
- the output doesn't need to be copied another time
- the extension can directly use bprintfrr() to put together pieces
The downside is that the theoretical length (regardless of available
buffer space) must be computed correctly.
Extended unit tests to test these paths a bit more thoroughly.
Signed-off-by: David Lamparter <equinox@diac24.net>
When "bgp bestpath peer-type multipath-relax" is enabled, multipaths
with both eBGP and iBGP learned routes may exist. It is not desirable
for the iBGP next hops to be discarded from the FIB because they are not
directly connected. When publishing a nexthop group to zebra, the
ZEBRA_FLAG_ALLOW_RECURSION flag is normally not set when the best path
is eBGP; when "bgp bestpath aspath multipath-relax" is configured, the
flag will now be set if any paths are from iBGP peers. This leaves
all-eBGP multipaths still requiring nexthops over connected routes.
Signed-off-by: Joanne Mikkelson <jmmikkel@arista.com>
This new BGP configuration is akin to "bgp bestpath aspath
multipath-relax". When applied, paths learned from different peer types
will be eligible to be considered for multipath (ECMP). Paths from all
of eBGP, iBGP, and confederation peers may be included in multipaths
if they are otherwise equal cost.
This change preserves the existing bestpath behavior of step 10's result
being returned, not the result from steps 8 and 9, in the case where
both 8+9 and 10 determine a winner.
Signed-off-by: Joanne Mikkelson <jmmikkel@arista.com>
This new test launches a small network composed by 4 OSPF routers with
Traffic Engineering and Segment Routing configuration. To assess the Link
State Traffic Engineering feature, the TED of each router is compared
against the reference TED which corresponds to the network topology.
Then a series of 6 steps, where Link, TE & SR configurations are modified
up to r4 shutwdown, are used to verify that the TED is correctly updated
on the 4 routers.
Signed-off-by: Olivier Dugeon <olivier.dugeon@orange.com>
Changes:
- Decrease hello interval to avoid packet loss slow downs
- Decrease dead interval to converge faster
- Remove previous 'Full' state check that wasn't checking for all
peers (only one per router)
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
The previous, more complex mechanism failed to take into account that
git worktrees only have a stub .git file & copying the worktree itself
is not enough. Just extract a file list beforehand & don't bother with
git inside the container.
Signed-off-by: David Lamparter <equinox@diac24.net>
Back when I put this together in 2015, ISO C11 was still reasonably new
and we couldn't require it just yet. Without ISO C11, there is no
"good" way (only bad hacks) to require a semicolon after a macro that
ends with a function definition. And if you added one anyway, you'd get
"spurious semicolon" warnings on some compilers...
With C11, `_Static_assert()` at the end of a macro will make it so that
the semicolon is properly required, consumed, and not warned about.
Consistently requiring semicolons after "file-level" macros matches
Linux kernel coding style and helps some editors against mis-syntax'ing
these macros.
Signed-off-by: David Lamparter <equinox@diac24.net>
The following error is shown when running the OSPFv3 tests
2021-03-16 23:37:44,792 INFO: Function returned global name 'data_rid' is not defined
2021-03-16 23:37:44,792 INFO: Retry [#1] after sleeping for 2s
2021-03-16 23:37:46,794 INFO: Verifying OSPF6 neighborship on router r1:
2021-03-16 23:37:46,993 INFO: Output for command [ show ipv6 ospf6 neighbor ] on router r1:
Neighbor ID Pri DeadTime State/IfState Duration I/F[State]
2.2.2.2 1 00:00:03 Full/PointToPoint 00:00:01 r1-r2-eth0[PointToPoint]
Fix the "data_rid" warning by using the correct variable
Signed-off-by: ckishimo <carles.kishimoto@gmail.com>
Currently there is a single interval for both RX and TX echo functions.
This commit introduces separate RX and TX timers for echo packets.
The main advantage is to be able to set the receive interval to zero
when we don't want to receive echo packets from the remote system.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
Additional example usage of iproute2_is_vrf_capable check in
isis-topo1-vrf topotest.
Signed-off-by: David Schweizer <dschweizer@opensourcerouting.org>
Example usage of iproute2_is_vrf_capable check in bgp_multi_vrf_topo1
and bgp_multi_vrf_topo2 topotests.
Signed-off-by: David Schweizer <dschweizer@opensourcerouting.org>
The test has been failing often recently and it is causing some false
positives for unrelated PRs.
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
We version the tests with the source code so we should no longer attempt
to support old versions in development branch.
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
The new ospf-sr-topo2 tests are much broader and detailed,
hence it makes no sense to keep the old ospf-sr-topo1
tests.
Signed-off-by: GalaxyGorilla <sascha@netdef.org>
1. Improved error meesage logging.
2. No functionality changes only put some meaningfull error messages.
Signed-off-by: Kuldeep Kashyap <kashyapk@vmware.com>
Avoid undocumented topotest dependency on installing en_US locale.
With this change dependency is removed.
Signed-off-by: Christian Hopps <chopps@labn.net>
Didn't test this but it's already randomly broken so cant be worse
Hopefully fixes:
raise InvalidCLIError("%s" % output)
InvalidCLIError: line 2: % Command incomplete[4]: bgp
large-community-list standard Test1 permit
Signed-off-by: Quentin Young <qlyoung@nvidia.com>
Pass the topogen 'tgen' object into the startRouterDaemons()
method. it can be used to start a debug cli immediately after
starting a daemon, and that can be handy.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
Sleeping when convergence is not guaranteed in 60 seconds
and then testing the rib to see if it has the data is
not a great way to have a test complete all the time.
Modify the code so that we check for convergence
and if we have converged then look in the rib.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
1. There were few tests where routes were configured with blackhole and
non-blackhole nexthops simultaneously, enhanced tests accordingly and
verified in master branch and with PR #8158 changes.
Signed-off-by: Kuldeep Kashyap <kashyapk@vmware.com>
Add some pytest.mark.bgpd. This is about all I could stomach doing
in one patch. I'll do another pass at another time.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
When the last SID in the TI-LFA repair list is an Adj-SID from the
penultimate hop router towards the final hop, the No-PHP flag of the
original Prefix-SID must be honored in the repair list itself since
the penultimate hop router won't have a chance to process that SID
and pop it if necessary.
Reported-by: Fredi Raspall <fredi@voltanet.io>
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
There are two fixes to handle slow convergence on ARM -
1. Ping on every re-try attempt to account for initial packet loss
2. Handle incomplete show outputs gracefully
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
The changes add the "jsoncmp_pass" and the "jsoncmp_fail" commands to
compare VTY shell's JSON output to an expected JSON object during
topotests using the LabN testing framework. This helps to eliminate
false negative test results (i.e. due to routes beeing out of order
after convergence or cosmetic changes in VTY shell's text output).
Signed-off-by: David Schweizer <dschweizer@opensourcerouting.org>
When parsing the output of "ip -6 address", allow arbitrary base interface
names (the part after "@" in the interface name), not just "if0-9". Without
this, link-local addresses sometimes are attributed to the wrong interface
because we're not matching the interface name but still handle the
interface's addresses.
Signed-off-by: Martin Buck <mb-tmp-tvguho.pbz@gromit.dyndns.org>
Make the generate-support-bundle script and interactions more
python3-friendly, and use python3 explicitly.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
Modify the timers on the bgp_blackhole_community test to
be more aggressive so our test system will recover faster
when we drop packets.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Add pytest marking for ospfd. This commit also has some other test markings
because I do not want to have to go through the same test multiple times.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
We have a ospfd.conf file in the r2 directory but the
ldp-sync-isis-topo1 test does not use ospf. Let's remove it.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Only one of the four reference files was present; add the missing
three. The test just silently passed if a ref file was missing:
change that to a failure.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
Add a test for the infinite recursion case fixed
with 0c4dbb5f8fe8fb188fa0e0aa8ce04764e893b79b
See that commit for details of the problem. This test uses a simpler
version of the repro found there as the test.
Signed-off-by: Stephen Worley <sworley@nvidia.com>
This test relied on the default addition of SVI MAC in zebra
now this has been fixed the test needs to be updated to work
with the new behaviour.
Signed-off-by: Pat Ruddy <pat@voltanet.io>
In test_converge_protocols() use sed to match the "show ip(v6) route"
header and strip it, rather than using tail which requires hardcoding
the expected length of the header (which is subject to change).
Signed-off-by: Duncan Eastoe <duncan.eastoe@att.com>
Since SNMP is a pain to install add a check which will be used
in all SNMP tests in future to silently skip SNMP tests if SNMP
has not been installed on the base system.
Signed-off-by: Pat Ruddy <pat@voltanet.io>
Adding test to verify default route is added when attached-bit
receive and send are enabled and not added when feature is disabled.
Signed-off-by: Lynne Morrison <lynne@voltanet.io>
This script involves Restart ospfd,
restart frr with ospf enabled,
staticd with redistribution inside ospf is enabled
Signed-off-by: nguggarigoud <nguggarigoud@vmware.com>
When P and Q spaces are adjacent then it makes sense to use adjacency SIDs to
from the P node to the Q node. There are some other corner cases where this
makes also sense like when a P/Q node adjacent to root node.
Signed-off-by: GalaxyGorilla <sascha@netdef.org>
1. Added 7 testcases to verify PIM BSM functionality. Here we have used Scapy
to send raw packet, generated using Cisco and FRR. Raw packets are kept in
Signed-off-by: Kuldeep Kashyap <kashyapk@vmware.com>
1. Added 8 testcases to verify PIM BSM functionality. Here we have used Scapy
to send raw packet, generated using Cisco and FRR. Raw packets are kept in
JSON file and sent tests on-demand in script.
Signed-off-by: Kuldeep Kashyap <kashyapk@vmware.com>
Tests were timing out in our test system due to lost packets and
flakiness of the lower end systems. Just set the timers to 3/10
and give them plenty of time to converge.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
New test does this:
a) Ensures that we run the correct number of times given two
`ip protocol X` commands( ie we do not run the route-map application
against all routes, only those affected )
b) Ensure that when we modify the route-map the state ends up sane
this includes making a static route depend on a sharp route that
gets removed from the change of the sharp route-map
c) Ensure that the kernel routes are correct.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Add the ability for our topotests to take advantage of pytest `mark`ing.
This effectively allows you to tell pytest to run against certain sets
of tests. For a demonstration purpose I've added in marks for:
babel
eigrp
ldp
ospf
pim
rip
And setup tests to run against those tests that only test those protocols.
You can run against eigrp tests by running `pytest -k eigrp`
Other combinations are also available based upon simple boolean logic.
Just read the pytest.mark documentation.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Simple test which creates a router running snmp and bgpd and
checks we can read the correct bgpVersion using snmp.
Signed-off-by: Pat Ruddy <pat@voltanet.io>
1. Adding api to verify ip nht command.
2. 5 cases of static routes with admin dist and tag
3. Run time = 89Secs
Signed-off-by: nguggarigoud <nguggarigoud@vmware.com>
Prepare the infrastructure to allow configuring and launching an SNMP
daemon as part of testing scenario.
Signed-off-by: Babis Chalios <babis@voltanet.io>
Signed-off-by: Pat Ruddy Chalios <pat@voltanet.io>
* If pathd binary is not found, skip the SR-TE topotests.
* Fix some compilation warnings when pathd is not built.
Signed-off-by: Sebastien Merle <sebastien@netdef.org>
* Added a new topotest to test bgpd listening on multiple addresses.
* Updated the existing bgpd tests according to the parameter added to
bgp_master_init.
Signed-off-by: "Adriano Marto Reis" <adrianomarto@gmail.com>
In test_bgp_mutli_vrf_topo2.py it's clear that we remove then
re-add the vrf interfaces. Then the test was immediately
checking to ensure that the routes were available.
BGP needs time to reconverge. Let's ensure that first.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Add new RLFA topotest that tests all RLFA configuration knobs and
how isisd and ldpd react to various configuration changes that can
occur in the network.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Extend the existing SPF unit testing infrastructure so that it can
test RLFA as well.
These new unit tests are useful to test the RLFA PQ node
computation on several different network topologies in a timely
manner. Artificial LDP labels (starting from 50000) are used to
activate the computed RLFAs.
It's worth mentioning that the computed backup routing tables
contain both local LFAs and remote LFAs, as running RLFA separately
isn't possible.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
The bgp_gr_functionality_topo1 test was shutting down an
interface on r2 and then trying to bring it up on r1.
Hijinx ensued.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
`lcommunity_gettoken` expects a space-delimeted list of 0 or more large
communities. `lcommunity_list_valid` can perform this check.
`lcommunity_list_valid` now validates large community lists more
accurately based on the following condition: Each quantity in a standard bgp
large community must:
1. Contain at least one digit
2. Fit within 4 octets
3. Contain only digits unless the lcommunity is "expanded"
4. Contain a valid regex if the lcommunity is "expanded"
Moreover we validate that each large community list contains exactly 3
such values separated by a single colon each.
One quirk of our validation which is worth documenting is:
```
bgp large-community-list standard test2 permit 1:c:3
bgp large-community-list expanded test1 permit 1:c:3
```
The first line will throw an error complaining about a "malformed community-list
value". The second line will be accepted because the each value is each treated as
a regex when matching large communities, it simply will never match anything so
it's rather useless.
Signed-off-by: Wesley Coakley <wcoakley@nvidia.com>
1. Enhanced lib/topojson.py for creating topologies with switches and routers
2. Ran it through (black) for expected formatting
Signed-off-by: kuldeepkash <kashyapk@vmware.com>
1. Enhanced lib/common_config.py for common configuration/verification needed
for PIM automation
2. Ran it through (black) for expected formatting
Signed-off-by: kuldeepkash <kashyapk@vmware.com>
1. Added lib/pim.py for PIM configuration/verification
2. Ran it through (black) for expected formatting
Signed-off-by: kuldeepkash <kashyapk@vmware.com>
An external label manager plugin may want to use the following
functions:
- create_label_chunk
- assign_label_chunk
- delete_label_chunk
- release_label_chunk
This test ensures that they are externally visible.
Signed-off-by: Pat Ruddy <pat@voltanet.io>
This test checks the interactions between the BGP label requesting
code and the labelpool code to ensure the correct number of labels
and label chunks are requested and those labels are freed back into
the pool when the corresponding prefix is removed.
Signed-off-by: Pat Ruddy <pat@voltanet.io>
Timestamps in test logs are needed for correlation with messages in
routing protocol log files. Vox populi indicates preference for
timestamp at beginning of line.
OLD:
(#55) scripts/rip-show.py:61 COMMAND:r1:vtysh -c "show ip rip status": 00:0.* 00:0:wait:RIP Peers:
NEW:
Sat Dec 19 08:26:45 2020 (#55) scripts/rip-show.py:61 COMMAND:r1:vtysh -c "show ip rip status": 00:0.* 00:0:wait:RIP Peers:
Signed-off-by: G. Paul Ziemba <paulz@labn.net>
While accidently running the topotests with version 3
I keep getting:
TypeError: `dict_values` object does not support indexing..
version 2 of python dict.values() returns a list.
version 3 does not
Write some code to allow both to be handled.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
This new daemon manages Segment-Routing Traffic-Engineering
(SR-TE) Policies and installs them into zebra. It provides
the usual yang support and vtysh commands to define or change
SR-TE Policies.
In a nutshell SR-TE Policies provide the possibility to steer
traffic through a (possibly dynamic) list of Segment Routing
segments to the endpoint of the policy. This list of segments
is part of a Candidate Path which again belongs to the SR-TE
Policy. SR-TE Policies are uniquely identified by their color
and endpoint. The color can be used to e.g. match BGP
communities on incoming traffic.
There can be multiple Candidate Paths for a single
policy, the active Candidate Path is chosen according to
certain conditions of which the most important is its
preference. Candidate Paths can be explicit (fixed list of
segments) or dynamic (list of segment comes from e.g. PCEP, see
below).
Configuration example:
segment-routing
traffic-eng
segment-list SL
index 10 mpls label 1111
index 20 mpls label 2222
!
policy color 4 endpoint 10.10.10.4
name POL4
binding-sid 104
candidate-path preference 100 name exp explicit segment-list SL
candidate-path preference 200 name dyn dynamic
!
!
!
There is an important connection between dynamic Candidate
Paths and the overall topic of Path Computation. Later on for
pathd a dynamic module will be introduced that is capable
of communicating via the PCEP protocol with a PCE (Path
Computation Element) which again is capable of calculating
paths according to its local TED (Traffic Engineering Database).
This dynamic module will be able to inject the mentioned
dynamic Candidate Paths into pathd based on calculated paths
from a PCE.
https://tools.ietf.org/html/draft-ietf-spring-segment-routing-policy-06
Co-authored-by: Sebastien Merle <sebastien@netdef.org>
Co-authored-by: Renato Westphal <renato@opensourcerouting.org>
Co-authored-by: GalaxyGorilla <sascha@netdef.org>
Co-authored-by: Emanuele Di Pascale <emanuele@voltanet.io>
Signed-off-by: Sebastien Merle <sebastien@netdef.org>
1. Enhanced framework to
a. Verify fib active routes(lib/common_config.py).
b. Verify bgp multi path routes(lib/bgp.py).
c. Create mininet nodes with different names(lib/topojson.py).
4. 12 Test cases of static routing with ibgp.
Test suite execution time is ~30 minutes.
5. 12 Test cases of static routing with ebgp.
Test suite execution time is ~30 minutes.
Signed-off-by: naveen <nguggarigoud@vmware.com>
The `show ip nht` and `show ipv6 nht` commands were broken.
This is because recent code commit: 0154d8ce45
assumed that p must not be NULL and this is not the case.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
1. As per recent changes done in PR #7652, we have modified the auto-rd verification logic
2. Dev PR link: https://github.com/FRRouting/frr/pull/7652
Signed-off-by: kuldeepkash <kashyapk@vmware.com>
I accidently installed something that is telling me about
unlosed handles in the tests. Let's clean them up.
<and yes I have no idea wtf I did>
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
The test_bgp_multi_vrf_topo2.py script had a bunch
of places where it would change an interface status
or add delete routes that would affect bgp convergence
but it was never ensuring that convergence had happened
before the test verified the bgp rib. I believe this
was leading to many intermittant ci failures in
testing for other PR's to be accepted. Modify
the code to wait for bgp convergence if we just
made a change to the topology
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
For each afi/safi of 'show bgp summary', display the peer description
each time needed. This information is useful, for instance in the case
of a device connected with multiple peers.
The topotest all_protocol_startup is changed accordingly.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
This is the opposite of TOPOTEST_AUTOLOAD: Instead of automatically loading
missing modules, TOPOTEST_NOLOAD prevents module loading and supresses
questions about it.
Signed-off-by: Martin Buck <mb-tmp-tvguho.pbz@gromit.dyndns.org>
the topolog importation folder must be precised. otherwise following
error message appears:
root@dut-vm:~/topotests/bgp_flowspec# python3 test_bgp_flowspec_topo.py
Traceback (most recent call last):
File "test_bgp_flowspec_topo.py", line 96, in <module>
from lib.lutil import lUtil
File "/root/topotests/bgp_flowspec/../lib/lutil.py", line 25, in <module>
from topolog import logger
ImportError: No module named 'topolog'
root@dut-vm:~/topotests/bgp_flowspec#
The same error occurs with lutil and bgprib which are 2 libraries
located under lib/ folder. Some precisions are added too.
PR=71290
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
python3 does not support execfile implementation.
replace it with open and exec api that are available in both python 2
and 3 implementations.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
This new topotest comprises of 13 testing steps and tests essentially
all implemented LFA knobs.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
These unit tests check the basic LFA loop-free condition on a
variety of different network topologies. None of the implemented
LFA tie-breakers are tested here.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
The tests work with the default settings of BFD meaning that bfdd
is able to recognize a 'down' link after ~900ms so a route
recovery should be visible in the RIB after 1 second.
The following topology is used:
+---------+
| |
eth-rt2 (.1) | RT1 | eth-rt3 (.1)
+----------+ 1.1.1.1 +----------+
| | | |
| +---------+ |
| |
| 10.0.2.0/24 |
| |
| eth-rt1 | (.2)
| 10.0.1.0/24 +----+----+
| | |
| | RT3 |
| | 3.3.3.3 |
| | |
(.2) | eth-rt1 +----+----+
+----+----+ eth-rt4 | (.1)
| | |
| RT2 | |
| 2.2.2.2 | 10.0.4.0/24 |
| | |
+----+----+ |
(.1) | eth-rt5 eth-rt3 | (.2)
| +----+----+
| | |
| | RT4 |
| | 4.4.4.4 |
| | |
| +----+----+
| 10.0.3.0/24 eth-rt5 | (.1)
| |
| |
| 10.0.5.0/24 |
| |
| +---------+ |
| | | |
+----------+ RT5 +----------+
eth-rt2 (.2) | 5.5.5.5 | eth-rt4 (.2)
| |
+---------+
Route recovery is tested on RT1. The focus here lies on the two
different routes to RT5. Link failures are generated by taking
down interfaces via the mininet Python interface on RT2 and RT3.
Hence routes are supposed to be adjusted to use RT3 when a link
failure happens on RT2 or vice versa.
Note that only failure recognition and recovery is "fast". BFD
does not monitor a link becoming available again.
Signed-off-by: GalaxyGorilla <sascha@netdef.org>
Commit 4c75f7c773 fixed a bug in which the TI-LFA repair paths
weren't preserving the original Prefix-SID of the routes. That
commit, however, didn't update the zebra interface code to account
for backup nexthops that don't have a repair list but do have a
SR label. As a consequence, backup nexthops that didn't have any
repair label were not preserving the original Prefix-SID of the
corresponding routes. Fix this and update the TI-LFA topotest
accordingly.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Once the remote end of a connected link is shut down (or lose
its address), isisd will remove the corresponding route from its
RIB after SPF runs. A new route for the same destination should
be computed based on the local LSP, and that route by definition
doesn't have any nexthop. The problem is that, when isisd tries
to replace the old route by the new one, it fails because routes
without nexthops can't be installed. That causes the old invalid
route to remain in the RIB when it shouldn't. To fix this problem,
change the zebra interface code to uninstall a route whenever it
can't be installed (because it lacks nexthops) instead of doing
nothing in that case.
This change should fix occasional failures of the test_isis_sr_topo1
topotest.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Fix lib to start loggin to correct daemon file on startup
Fix bgp-auth tests for the logging changes
Fixes Issue # 7545
Signed-off-by: Martin Winter <mwinter@opensourcerouting.org>
1) in generate_ips if start_ipaddr does not have a `/` in it
there exists a code path where both mask and step are
null values. Write a bit of code to ensure this pre-req
is found early and often
2) in verify_rib there exists a code path where static_route
is null when we get to the non static route section. Change
the code to operate on the advertise_network_dict that
we are iterating over.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Within unit tests the output of vtysh commands is compared to hand
made reference files. For some reason the output of those vtysh
commands contains Windows Style newlines which results in error
outputs which make it hard to identify this problem.
Since there seems to be no benefit in checking those newlines
anyway this commit just normalizes them.
Signed-off-by: GalaxyGorilla <sascha@netdef.org>
Move the FOREACH_AFI_SAFI macro from bgpd.h to zebra.h( GLOBAL's YOUALL )
Then convert all the places that have the two level for loop to
iterate over all afi/safis
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
1. Added convergence step just after BGP-GR capablities are exchanged and clear bgp
is performed , reason for this is, in few machine bgp sessions are taking more time
to come up.
Signed-off-by: Kuldeep Kashyap <kashyapk@vmware.com>
1. Removed UTP test cases keeping only functional test as part of these suites
2. Added convergence step just after BGP-GR capablities are exchanged and clear bgp
is performed, reason for this is, in few machine bgp sessions are taking more time
to come up.
Signed-off-by: Kuldeep Kashyap <kashyapk@vmware.com>
Reduce the number of routes used in the route-scale test: we're
having memory troubles, and this may help the CI run with fewer
false failures. Also re-orged the route-scale test code a bit
so it can be driven from the json file, with fewer hard-coded
values.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
Add support to compare the number of RIB nexthops, rather than the
specific nexthop addresses. Use this in the bgp_ecmp topotests that
test maximum-paths - testing the specific nexthops is wrong there,
it's not deterministic and we get spurious failures.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
Make tests more robust to changing show outputs by searching for
item of interest rather than using a fixed index.
Signed-off-by: Pat Ruddy <pat@voltanet.io>
When all the uplinks are disabled the access ports used for multihoming
are error-disabled/protodowned.
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
1. The default startup-delay for multihomed devices is three minutes. While
that is necessary/reasonable for a real network it is not needed for a
test env. Lower the startup-delay to 1s to keep the test run time low.
2. Configure uplinks for mh uplink-tracking
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
Add the following Anycast-SIDs on routers rt4 and rt5:
* segment-routing prefix 10.10.10.10/32 index 100 no-php-flag n-flag-clear
* segment-routing prefix 2001:db8:1000::10/128 index 101 no-php-flag n-flag-clear
The updated JSON data will then check whether the Anycast-SIDs are
being processed as expected (e.g. rt1 should use ECMP to rt2 and rt3,
rt2 should use rt4 only as it's directly connected, etc).
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
When computing backup nexthops for routes that contain a Prefix-SID,
the original Prefix-SID label should be present at the end of
backup label stacks (after the repair labels). This commit fixes
that oversight in the original TI-LFA code. The SPF unit tests and
TI-LFA topotes were also updated accordingly.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Embed Prefix-SID information inside SPF data structures so that
Prefix-SIDs can be installed together with their associated routes
at the end of the SPF algorithm. This is different from the current
implementation where Prefix-SIDs are parsed and processed separately,
which is vastly suboptimal.
Advantages of the new code:
* No need to parse the LSPDB an additional time to detect and process
SR-related changes;
* Routes are installed with their Prefix-SID labels in the same ZAPI
message. This can prevent packet dropping for a few milliseconds
after each SPF run if there are BGP-labeled routes (e.g. L3VPN) that
recurse on IGP labeled routes;
* Much easier to support Anycast-SIDs, as the SPF code will naturally
figure out the best nexthops and use only them (that can't be done
in any reasonable way if the Prefix-SID Sub-TVLs are processed
separately);
* Less code to maintain and reduced memory footprint;
The "show isis segment-routing prefix-sids" command was removed as
it doesn't make sense anymore now that "show isis route" exists.
Prefix-SIDs are a property of routes, so what was done was to extend
the "show isis route" command with a new "prefix-sid" option that
changes the output table to show the Prefix-SID information associated
to each route.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
This is preparatory change for the upcoming SR Prefix-SID
refactoring.
Since Prefix-SID information will be stored inside IS-IS routes
(instead of being maintained separately), it will be necessary to
have local routes in order to store local Prefix-SID information.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Change thread_cancel to take a ** to an event, NULL-check
before dereferencing, and NULL the caller's pointer. Update
many callers to use the new signature.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
Add test for new aggregate address option: test aggregate address option
without converged routes, then test again with a different route map
with converged routes.
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
Create appropriate accessor functions for the rn->lock
data. We should be accessing this data through accessor
functions since it is private data to the data structure.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Skip comparing neighbor-extended-circuit-id in yang output. They
are not consistent.
This is similar to commit ecc11c93b7 which fixed the same
problem in the IS-IS SR topotest.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
1. Suite: evpn_type5_test_topo1 was added to pytest.ini during triaging phase as
there was bug: https://github.com/FRRouting/frr/issues/6867, which is fixed. Enabling
suite to be run in CI.
Signed-off-by: Kuldeep Kashyap <kashyapk@vmware.com>
1. Adding test to verify well known communities: no-export, local-AS, internet
2. Exection time is 90 sec
Signed-off-by: Kuldeep Kashyap <kashyapk@vmware.com>
The code pattern:
for (ALL_LSDB(lsdb, lsa)) {
remove_lsa(lsa)
}
has a use after free in ALL_LSDB, since we ask for the next pointer,
after it has been freed.
Modify the code such that we grab the next pointer before we can
possibly free it.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Force faster generation of lsp's and also cause the
networks to converge faster. All affected tests
run faster now.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
The bgp_l3vpn_to_bgp_vrf test is looking for a prefix
on multiple routers that the ordered received is non-deterministic.
As such the regex's are failing occassionaly when the
route is received in an unexpected order.
One possible order:
(#89) scripts/check_routes.py:120 COMMAND:ce3:vtysh -c "show bgp ipv4 uni 6.0.1.0":2 available, best .*192.168.1.1.* Local.* 99.0.0.3 from 0.0.0.0 .99.0.0.3.* Origin IGP, metric 200, localpref 50, weight 32768, valid, sourced, local, best .Weight.* Community: 0:67.* Extended Community: RT:89:123.* Large Community: 12:34:56.* Local.* 192.168.1.1 from 192.168.1.1 .192.168.1.1.* Origin IGP, metric 98, localpref 123, valid, internal.* Community: 0:67.* Extended Community: RT:52:100 RT:89:123.* Large Community: 12:34:56:pass:Redundant route 1 details c:
COMMAND OUTPUT:BGP routing table entry for 6.0.1.0/24^M
Paths: (2 available, best #1, table default)^M
Advertised to non peer-group peers:^M
192.168.1.1^M
Local^M
99.0.0.3 from 0.0.0.0 (99.0.0.3)^M
Origin IGP, metric 200, localpref 50, weight 32768, valid, sourced, local, best (Weight)^M
Community: 0:67^M
Extended Community: RT:89:123^M
Large Community: 12:34:56^M
Last update: Wed Oct 7 11:12:22 2020^M
Local^M
192.168.1.1 from 192.168.1.1 (192.168.1.1)^M
Origin IGP, metric 98, localpref 123, valid, internal^M
Community: 0:67^M
Extended Community: RT:52:100 RT:89:123^M
Large Community: 12:34:56^M
Last update: Wed Oct 7 11:12:41 2020:
R:89 ce3 Redundant route 1 details c 1 0
Second possible order:
(#89) scripts/check_routes.py:120 COMMAND:ce3:vtysh -c "show bgp ipv4 uni 6.0.1.0":2 available, best .*192.168.1.1.* Local.* 99.0.0.3 from 0.0.0.0 .99.0.0.3.* Origin IGP, metric 200, localpref 50, weight 32768, valid, sourced, local, best .Weight.* Community: 0:67.* Extended Community: RT:89:123.* Large Community: 12:34:56.* Local.* 192.168.1.1 from 192.168.1.1 .192.168.1.1.* Origin IGP, metric 98, localpref 123, valid, internal.* Community: 0:67.* Extended Community: RT:52:100 RT:89:123.* Large Community: 12:34:56:pass:Redundant route 1 details c:
COMMAND OUTPUT:BGP routing table entry for 6.0.1.0/24^M
Paths: (2 available, best #2, table default)^M
Advertised to non peer-group peers:^M
192.168.1.1^M
Local^M
192.168.1.1 from 192.168.1.1 (192.168.1.1)^M
Origin IGP, metric 98, localpref 123, valid, internal^M
Community: 0:67^M
Extended Community: RT:52:100 RT:89:123^M
Large Community: 12:34:56^M
Last update: Wed Oct 7 11:14:45 2020^M
Local^M
99.0.0.3 from 0.0.0.0 (99.0.0.3)^M
Origin IGP, metric 200, localpref 50, weight 32768, valid, sourced, local, best (Weight)^M
Community: 0:67^M
Extended Community: RT:89:123^M
Large Community: 12:34:56^M
Last update: Wed Oct 7 11:14:27 2020:
R:89 ce3 Redundant route 1 details c 0 1
BGP displays the paths in the order received since it's just a linked list.
For this test modify/add the luCommands to track that we may
receive the paths in a non-deterministic order.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Signed-off-by: Quentin Young <qlyoung@nvidia.com>
Add a new topology test for `aggregate-address` to test
`matching-MED-only` and its combination with `summary-only`.
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
In test_peer_attr.c test is initializd with vty handler
but candiate_config is not set.
northbound converted bgp cli expects to derefence the
candidate_config field which leads to crash.
(gdb) p *test->vty->candidate_config
$9 = {dnode = 0x0, version = 0}
Signed-off-by: Chirag Shah <chirag@nvidia.com>
Make sure the all-protocols test_isis_interfaces testcase uses
a regex substitution that includes all the hex characters.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
The pim-basic suite uses some private python scripts to
send and receive mcast traffic: revise them to support
both py2 and py3.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
Ensure the list of daemons to start is either the one specified
by a caller or the default one from the router configuration.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
The linux kernel is getting RTM_F_TRAP and RTM_F_OFFLOAD for
kernel routes that have an underlying asic offload. Write the
code to receive these notifications from the linux kernel and
to store that data for display about the routes.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
The Solaris code has gone through a deprecation cycle. No-one
has said anything to us and worse of all we don't have any test
systems running Solaris to know if we are making changes that
are breaking on Solaris. Remove it from the system so
we can clean up a bit.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
1. Added 2 tests to verify bgp route aggregation using summary-only and
as-set commands
2. Execution time is ~90 sec
Signed-off-by: Kuldeep Kashyap <kashyapk@vmware.com>
1. Removed initial_wait in ospf library.
2. Removed one test case which was random
failure, will add back after traiging.
Signed-off-by: naveen <nguggarigoud@vmware.com>
1. Adding 18 ospf testcases to topojson.
2. Adding ospf.py library.
Test suite execution time is ~18 minutes.
Signed-off-by: naveen <nguggarigoud@vmware.com>
1. Added linux kernel version check to avoid failures
in CI systems if matching kernel version not found.
Signed-off-by: naveen <nguggarigoud@vmware.com>
We have a bunch of tests that wait *then* check a command for success/failure.
Modify the tests to check *first* then to wait. This reduces test
run times on my system by ~1400 seconds for a full run.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
this test checks connectivity between a vrf-lite device and a vrf-netns
device. this ensures that evpn serice is importing appropriate evpn rt5
entries in the correct vrf.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Modify bgpd.conf in all easily accessible topotests to use 3 10
as their timers du jour. This will allow the tests to converge
faster.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Reduces run time of the bgp_l3vpn_to_bgp_vrf topotests
from ~118 seconds to ~87 seconds by reducing hello timers
in bgp and ospf
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reduce run time of bfd-topo2 from ~62 seconds to ~33 seconds
by modifying the hello/dead intervals for both ospf and ospfv3
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reduce the runtime from ~82 seconds to ~51 seconds by
reducing hello/hold timers for both bgp and ospf.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reduce run time from ~114 seconds to ~55 seconds by
configuring hello/dead interval timers for ospf and ospfv3
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reduce run time from ~76 seconds to ~47 seconds by modifying
both bgp and ospf timers to be more aggressive
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reduce this tests run time from ~76 seconds to ~49 seconds
by decreasing the hello/dead interval timers in ospf
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Decrease run time from ~70 seconds to ~41 seconds by
reducing hello/dead interval timers in ospf
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Decrease run time from ~70 seconds to ~60 seconds
by modifying the hello/dead interval interface timers
in ospf
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reduce ospf-sr-topo1 run time from ~60 seconds to ~30 seconds
by shortening the hello and dead timers.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Convert run times by lowering hello/dead interval timers to
smaller values from ~66 seconds to ~36 seconds.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Initial run of topotests on my machine takes ~210 seconds
With these changes we are at ~40 seconds
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
1. Added test to verify bgp vrf dynamic route leak functionality
2. Total execution time is ~8 mins
3. Added kernel version check, these script would be run for kernel version >= 4.19
Signed-off-by: Kuldeep Kashyap <kashyapk@vmware.com>
1. Topotest for isis-vrf is added for ipv4 and ipv6.
2. Test case for checking isis topology.
3. Test case for checking zebra isis routes.
4. Test case for checking linux vrf routes.
5. 2 new API's written in topotest/lib for checking vrf routes.
Co-authored-by: Kaushik <kaushik@niralnetworks.com>"
Signed-off-by: harios_niral <hari@niralnetworks.com>
1. Added isis with different vrf and it's dependecies.
2. Added new vrf leaf in yang.
3. A minor change for IF_DOWN_FROM_Z passing argrument is
replaced with ifp pointer in api "isis_if_delete_hook()".
4. Minor fix in the isisd spf unit test.
Co-authored-by: Kaushik <kaushik@niralnetworks.com>"
Signed-off-by: harios_niral <hari@niralnetworks.com>
Avoid unnecessary use of StringIO in one place, use version-
dependent method in another. Remove a couple of other py2->py3
problems.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
RFC 7490 says:
"The reverse SPF computes the cost from each remote node to root. This
is achieved by running the normal SPF algorithm but using the link
cost in the direction from the next hop back towards root in place of
the link cost in the direction away from root towards the next hop".
Support for reverse SPF will be necessary later as it's one of the
algorithms used to compute R-LFA/TI-LFA repair paths.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Now that the IS-IS SPF code is more modular, write some unit tests
for it.
This commit includes a new test program called "test_isis_spf" which
can load any test topology (there are 13 different ones available)
and run SPF on any desired node. In the future this same test program
and topologies will also be used to test reverse SPF and TI-LFA.
The "test_common.c" file contains helper functions used to parse the
topology descriptions from "test_topologies.c" into LSP databases
that can be used as an input to the SPF code.
This commit also introduces the F_ISIS_UNIT_TEST flag which is used
to prevent the IS-IS code from scheduling any event when running
under the context of an unit test.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Change the public router stop method to always do a two-phase
shutdown - once without waiting and a second time with a wait.
Ordinary callers need to use this approach when stopping routers.
Move the detailed internal details to a private method that tests
should not call directly.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
this test ensures that an incoming bgp ipv4 and ipv6 flowspec
entry is received with a nexthop IP associated.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
In case of config rollback is enabled,
record northbound transaction based on a control flag.
The actual frr daemons would set the flag to true via
nb_init from frr_init.
This will allow test daemon to bypass recording
transacation to db.
Signed-off-by: Chirag Shah <chirag@nvidia.com>
Add new option to `segment-routing prefix` command to set the
Explcit Null flag in addition to the No-PHP flag. MPLS LFIB configuration
has been also updated to take into account the Explicit Null flag.
Signed-off-by: Olivier Dugeon <olivier.dugeon@orange.com>
RFC 8665 defines a Segment Routing Local Block for Adjacency SID.
This patch provides the possibility to modify the SRLB as well as
reserved the block range from the Label Manager.
- Introduce new CLI 'segment-routing local-block'
- Add local block to SRDB structure
- Parse / Serialize SRLB in Router Information LSA
- Update OSPF-SR topotest
- Update documentation
Signed-off-by: Olivier Dugeon <olivier.dugeon@orange.com>
1. Created a structure "isis master".
2. All the changes are related to handle ISIS with different vrf.
3. A new variable added in structure "isis" to store the vrf name.
4. The display commands for isis is changed to support different VRFs.
Signed-off-by: Kaushik <kaushik@niralnetworks.com>
Add a new test to cover the new features for multi hop BFD peers:
- Test that we correctly receive TTL from protocol integration.
- Check minimum TTL usage and 'show' command.
- Check for passive mode.
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
The commit `bfdd: simplify and remove duplicated code` fixed a problem
that was causing the protocol configuration to override the user
configuration.
In this test case: the peer was configured to be disabled (default is
`shutdown`) and the test was expecting it to get activated (`no shutdown`)
when the protocol converged. I changed the peer default state to
`no shutdown`, however another way to get the same effect is to
configure the protocol to use a profile or don't configure a peer at all
(and use the defaults).
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
Since the values of ifindices cannot be relied upon across
distributions, simpy remove them from the VNI JSON being compared.
Signed-off-by: Pat Ruddy <pat@voltanet.io>
add tests to check IP address/MAC address associations are learned
from netlink NEWNEIGH messages and are propagated to the remote PE
Signed-off-by: Pat Ruddy <pat@voltanet.io>
With these changes the IS-IS SR topotest should run to completion
about twice as fast compared to before (4 -> 2 minutes on my
machine).
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
For the sake of Segment Routing (SR) and Traffic Engineering (TE)
Policies there's a need for additional infrastructure within zebra.
The infrastructure in this PR is supposed to manage such policies
in terms of installing binding SIDs and LSPs. Also it is capable of
managing MPLS labels using the label manager, keeping track of
nexthops (for resolving labels) and notifying interested parties about
changes of a policy/LSP state. Further it enables a route map mechanism
for BGP and SR-TE colors such that learned BGP routes can be mapped
onto SR-TE Policies.
This PR does not introduce any usable features by now, it is just
infrastructure for other upcoming PRs which will introduce 'pathd',
a new SR-TE daemon.
Co-authored-by: Renato Westphal <renato@opensourcerouting.org>
Co-authored-by: GalaxyGorilla <sascha@netdef.org>
Signed-off-by: Sebastien Merle <sebastien@netdef.org>
The vxlan `ip... ` command is failing because we are passing in
`no learning` and that is failing.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Add a bit of a clue to the test_evpn_type5_topo1.py script
to what dut is failing, when things go south.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
When the topotest mem-leak reporting is enabled, use the same
two-step daemon stop procedure that's used in
the topogen.stop_topology path.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
The base topology is a two level CLOS with two racks. There are
two PEs/TORs in each rack that provide active-active redundancy to
two dual-attached servers in the rack. And EVPN-PIM is used for
flooded traffic.
Reference: evpn-mh-topo-tests.pdf
Tests have been added for the following functionality -
1. ES management
2. EAD/Type-1 route handling
3. Type-2 route with non-zero ESI
4. MAC sync and remote MAC (with remote-ES destination) handling
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
When you make a change to a route-map or a prefix-list it depends on, note
that the route-map needs to be reprocessed for the change.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
`sharpd` doesn't handle any route map commands and neither should show
up in route map commands. This makes the CI pass again after not sending
route map commands to it again.
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
Address-sanitizer runs in the CI appear to require more
memory than is available (at present), so skip the top
x32 route_scale testcase when running with <4G of ram.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
Make some changes to the route-scale topotest, in view of
issue #6734. Table-drive the test to eliminate some
repeated code. Assert and fail if a step in the progression
of scale fails. Wait a little longer between checking the show
output - it's costly to generate that output at scale. Add a
memleak testcase.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
1. evpn_type5_test_topo1 tests started failing in CI for all Ubuntu 18.04 machine,
which are having kernel version: 5.4.0-42-generic
2. We will enable these tests once issue is found and fixed.
Signed-off-by: Kuldeep Kashyap <kashyapk@vmware.com>
The `log monitor' command is a no-op and actually
outputs a `this doesn't do anything` warning. Let's remove
this cli line from our tests as that don't do anything and
people will look at these configs for guidance.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
add thread info, use "bt full" to get variables and add a bit of
disassembly for good measure.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
1. Increasing BGP convergence wait time to overcome Ubuntu 16.04 arm8 box, as
bgp neighorship is taking more time in this particular testbed.
2. Debugged bgp-ecmp-topo2 failures and here also it seems to be bgp convergence
issue, doing some enhancement in scripts to handle it
Signed-off-by: Kuldeep Kashyap <kashyapk@vmware.com>
Remove mid-string line breaks, cf. workflow doc:
.. [#tool_style_conflicts] For example, lines over 80 characters are allowed
for text strings to make it possible to search the code for them: please
see `Linux kernel style (breaking long lines and strings)
<https://www.kernel.org/doc/html/v4.10/process/coding-style.html#breaking-long-lines-and-strings>`_
and `Issue #1794 <https://github.com/FRRouting/frr/issues/1794>`_.
Scripted commit, idempotent to running:
```
python3 tools/stringmangle.py --unwrap `git ls-files | egrep '\.[ch]$'`
```
Signed-off-by: David Lamparter <equinox@diac24.net>
Stop printing hard-coded 30 seconds in a couple of places in
bgp.py in the topojson infra - print the actual time
spent waiting.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
Remove a special-case clause for static routes - it was the same
as the clause for other recursive routes. Have staticd just tell
zebra that recursion is allowed. Update topotest that was aware
of this 'internal' flag.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
1. It will generate support bundle/sump data on test failures
2. It used /usr/lib/frr/generate_support_bundle.py utility to dump the data
Signed-off-by: Kuldeep Kashyap <kashyapk@vmware.com>
Another short timeout for bgp - make the
verify_bgp_convergence_from_running_config() api use the same
generous timeout as verify_bgp_convergence()
Signed-off-by: Mark Stapp <mjs@voltanet.io>
There exists the possiblity that the hello timer printed would
show a time to expiration in this format:
Hello due in 350 usecs
The tests are looking for:
Hello due in 5.430s
Just notice that we may have gotten usecs and act accordingly
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
1. Added 7 test cases to verify bgp recursive nexthop and ebgp multi-hop functionality
2. Added framework support to automate these test cases
3. Total execution time is ~5 mins
Signed-off-by: Kuldeep Kashyap <kashyapk@vmware.com>
Use the right list of daemons to avoid trying to start zebra twice.
Change a zebra log message to INFO level to avoid stderr check
failure.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
Add a few retries during router shutdown before killing a daemon. Also
work harder to start only a single instance of daemons, esp. zebra.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
The tests work with the default settings of BFD meaning that bfdd is
able to recognize a 'down' link after ~900ms so a route recovery should
be visible in the RIB after 1 second.
In the current state only IPv4 is used (when using IPv6
autoconfiguration) within BFD, even though the recovery also affects
IPv6 routes. This is different to the current state of ospfd/ospf6d in
combination with BFD since both IPv4 and IPv6 sessions are used there.
The following topology is used:
+---------+
| |
eth-rt2 (.1) | RT1 | eth-rt3 (.1)
+----------+ 1.1.1.1 +----------+
| | | |
| +---------+ |
| |
| 10.0.2.0/24 |
| |
| eth-rt1 | (.2)
| 10.0.1.0/24 +----+----+
| | |
| | RT3 |
| | 3.3.3.3 |
| | |
(.2) | eth-rt1 +----+----+
+----+----+ eth-rt4 | (.1)
| | |
| RT2 | |
| 2.2.2.2 | 10.0.4.0/24 |
| | |
+----+----+ |
(.1) | eth-rt5 eth-rt3 | (.2)
| +----+----+
| | |
| | RT4 |
| | 4.4.4.4 |
| | |
| +----+----+
| 10.0.3.0/24 eth-rt5 | (.1)
| |
| |
| 10.0.5.0/24 |
| |
| +---------+ |
| | | |
+----------+ RT5 +----------+
eth-rt2 (.2) | 5.5.5.5 | eth-rt4 (.2)
| |
+---------+
Route recovery is tested on RT1. The focus here lies on the two
different routes to RT5. Link failures are generated by taking
down interfaces via the mininet Python interface on RT2 and RT3.
Hence routes are supposed to be adjusted to use RT3 when a link
failure happens on RT2 or vice versa.
Note that only failure recognition and recovery is "fast". BFD
does not monitor a link becoming available again.
Signed-off-by: GalaxyGorilla <sascha@netdef.org>
Instead of waiting for daemons start with `sleep`, start them with the
`-d` parameter so they can release the terminal themselves when ready.
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
Start logging early everything (including debug) to
`/tmp/topotest/<test>/<node>/<daemon>.{out,err}`.
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
Handle the duplicated code with a simple conditional: if called from
specialized API use provided daemons configuration, otherwise fallback
to old `Router` own daemon settings.
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
Just disable pbr tests on anything less than 4.10.
This has to do with the fact that the arm platform
is not allowing us to install a route into a
non default table using a interface associated
with a vrf.
ip route add default 4.5.6.7 via swp39 table 10000
When swp39 is in a vrf other than default
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
From last addition we can tell that the nexthop-group C is
installed but pbr does not think it is. This failure
has been consistent the last 4-5 runs in master. Lets
add a bit more data gathering to figure out what is going on.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Include vrf name with interface name when topojson framework
generates interface configuration. This matches the output of
'show runn', and makes config reset less disruptive. Also
stop removing configured debugs and log output when re-generating
config.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
This may be expanded in the future as we figure out more things
to gather when the test has gone south.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
This is the bulk part extracted from "bgpd: Convert from `struct
bgp_node` to `struct bgp_dest`". It should not result in any functional
change.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Under heavy load some systems may still be processing. Let's give
the system some time to figure out what is going wrong.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Announcements that are marked as invalid were previously not revalidated.
This was fixed by replacing the range lookup with a subtree lookup.
Signed-off-by: Marcel Röthke <marcel.roethke@haw-hamburg.de>
Import a topology with some protocols that integrate with BFD. As other
daemons get the new BFD profile support we can update the test to cover
them.
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
Error Message seen:
2020-06-11 14:00:35,288 ERROR: assert failed at "test_ebgp_ecmp_topo2/test_ecmp_after_clear_bgp[redist_static]": Testcase test_ecmp_after_clear_bgp[redist_static] : Failed
Error: TIMEOUT!! BGP is not converged in 30 seconds for router r3
assert 'TIMEOUT!! BGP is not converged in 30 seconds for router r3' is True
if a retry for a failed connection is 120 seconds we should wait slightly
longer than a retry session, which this clear test was not doing.
Especially since we know our topotests are lossy on data under load.
Apparently I changed this earlier to 90 seconds, but a retry window
is 120. Not sure wtf I was thinking
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Add some basic route scale tests to ensure that we can
install a large number of routes. Also grab some timings
so that we can keep track and see if anything substantially
changes over time.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
