The pl330 DMA controller provides number of DMA channels and requests
through its registers, so duplicating this information (with a chance of
mistakes) in DTS is pointless. Additionally the DTS used always wrong
property names which causes DT schema check failures - the bindings
documented 'dma-channels' and 'dma-requests' properties without leading
hash sign.
Reported-by: Rob Herring <robh@kernel.org>
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220430121902.59895-9-krzysztof.kozlowski@linaro.org
The external oscillator - XTCXO - is an input to the SoC. It is defined
in the Exynos Auto v9 SoC DTSI, because all boards will provide it and
clock controller bindings expect it, however the actual frequency of the
clock should be determined by the board.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Chanho Park <chanho61.park@samsung.com>
Link: https://lore.kernel.org/r/20220503092631.174713-1-krzysztof.kozlowski@linaro.org
WLAN rail was leaking power during RBSC/sleep even after turning BT off.
Change active and sleep pinctrl configurations to handle same.
Signed-off-by: Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1650556567-4995-3-git-send-email-quic_vnivarth@quicinc.com
WLAN rail was leaking power during RBSC/sleep even after turning BT off.
Change active and sleep pinctrl configurations to handle same.
Signed-off-by: Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1650556567-4995-2-git-send-email-quic_vnivarth@quicinc.com
This device node is unused now that we've removed the driver that
consumed it in the kernel. Drop the unused node to save some space.
Cc: Alex Elder <elder@linaro.org>
Cc: Taniya Das <quic_tdas@quicinc.com>
Cc: Mike Tipton <quic_mdtipton@quicinc.com>
Cc: Georgi Djakov <djakov@kernel.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Acked-by: Georgi Djakov <djakov@kernel.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220415005828.1980055-1-swboyd@chromium.org
Allwinner A64 SoC has separate supplies for PC, PD, PE, PG and PL.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220430191009.73946-1-harald@ccbib.org
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmJu9FYeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGAyEH/16xtJSpLmLwrQzG
o+4ToQxSQ+/9UHyu0RTEvHg2THm9/8emtIuYyc/5FgdoWctcSa3AaDcveWmuWmkS
KYcdhfJsaEqjNHS3OPYXN84fmo9Hel7263shu5+IYmP/sN0DfQp6UWTryX1q4B3Q
4Pdutkuq63Uwd8nBZ5LXQBumaBrmkkuMgWEdT4+6FOo1mPzwdIGBxCuz1UsNNl5k
chLWxkQfe2eqgWbYJrgCQfrVdORXVtoU2fGilZUNrHRVGkkldXkkz5clJfapyZD3
odmZCEbrE4GPKgZwCmDERMfD1hzhZDtYKiHfOQ506szH5ykJjPBcOjHed7dA60eB
J3+wdek=
=39Ca
-----END PGP SIGNATURE-----
Merge 5.18-rc5 into usb-next
We need the USB fixes in here, and this resolves a merge issue in
drivers/usb/dwc3/drd.c
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- ADC, SDHI, CAN-FD, I2C, QSPI, timer, watchdog, sound, USB, SPI, GPU,
cpufreq, and thermal support for the RZ/V2L SoC, and the RZ/V2L
SMARC EVK development board,
- USB, I2C, Audio, NOR Flash, timer, SPI support for RZ/G2LC SMARC EVK
development board,
- Can-FD support for the R-Car M30W+ and V3U SoCs, and the Falcon
development board,
- I2C and GPIO support for the R-Car S4-8 SoC,
- I2C EEPROM support for the Falcon development board,
- SPI Multi I/O Bus Controller (RPC-IF) support for the R-Car H3,
M3-W(+), M3-N, E3, and D3 SoCs,
- RPC HyperFlash support for the Draak, Ebisu, Salvator-X(S), and ULCB
development boards,
- Initial support (UART, DMAC, pin control, SDHI, eMMC, Ethernet) for
the RZ/G2UL SoC, and the RZ/G2UL SMARC EVK development board,
- Miscellaneous fixes and improvements.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCYmJ+7gAKCRCKwlD9ZEnx
cE5hAQDebyQdMMpgRgOC4ES3leIRrMJSmOAjrQcQjrTUJ6WYNgD9Gj8USqudA/By
Toz6dahFUSI0MDbgqnBjiqMGbEnbNww=
=xap2
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=SiTm
-----END PGP SIGNATURE-----
Merge tag 'renesas-arm-dt-for-v5.19-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/dt
Renesas ARM DT updates for v5.19
- ADC, SDHI, CAN-FD, I2C, QSPI, timer, watchdog, sound, USB, SPI, GPU,
cpufreq, and thermal support for the RZ/V2L SoC, and the RZ/V2L
SMARC EVK development board,
- USB, I2C, Audio, NOR Flash, timer, SPI support for RZ/G2LC SMARC EVK
development board,
- Can-FD support for the R-Car M30W+ and V3U SoCs, and the Falcon
development board,
- I2C and GPIO support for the R-Car S4-8 SoC,
- I2C EEPROM support for the Falcon development board,
- SPI Multi I/O Bus Controller (RPC-IF) support for the R-Car H3,
M3-W(+), M3-N, E3, and D3 SoCs,
- RPC HyperFlash support for the Draak, Ebisu, Salvator-X(S), and ULCB
development boards,
- Initial support (UART, DMAC, pin control, SDHI, eMMC, Ethernet) for
the RZ/G2UL SoC, and the RZ/G2UL SMARC EVK development board,
- Miscellaneous fixes and improvements.
* tag 'renesas-arm-dt-for-v5.19-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel: (55 commits)
ARM: dts: r9a06g032: Drop "arm,cortex-a7-timer" from timer node
arm64: dts: renesas: r8a779f0: Add GPIO nodes
arm64: dts: renesas: rzg2ul-smarc-som: Enable Ethernet on SMARC platform
arm64: dts: renesas: rzg2ul-smarc-som: Enable eMMC on SMARC platform
arm64: dts: renesas: rzg2ul-smarc: Enable microSD on SMARC platform
arm64: dts: renesas: r9a07g043: Add GbEthernet nodes
arm64: dts: renesas: r9a07g043: Add SDHI nodes
arm64: dts: renesas: rzg2ul-smarc: Add scif0 and audio clk pins
arm64: dts: renesas: r9a07g043: Fillup the pinctrl stub node
arm64: dts: renesas: Add initial device tree for RZ/G2UL Type-1 SMARC EVK
arm64: dts: renesas: Add initial DTSI for RZ/G2UL SoC
arm64: dts: renesas: rzg2l-smarc: Move gpios property of vccq_sdhi1 from common dtsi
arm64: dts: renesas: rzg2lc-smarc: Enable RSPI1 on carrier board
arm64: dts: renesas: ulcb: Add RPC HyperFlash device node
arm64: dts: renesas: salvator-common: Add RPC HyperFlash device node
arm64: dts: renesas: ebisu: Add RPC HyperFlash device node
arm64: dts: renesas: draak: Add RPC HyperFlash device node
arm64: dts: renesas: rcar-gen3: Add RPC device nodes
arm64: dts: renesas: rcar-gen4: Add interrupt properties to watchdog nodes
arm64: dts: renesas: rzg2: Add interrupt properties to watchdog nodes
...
Link: https://lore.kernel.org/r/cover.1650638505.git.geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The reference clock for the HDMI controller has been renamed to 'ref',
the previous 'vpll' name is only left for compatibility in the driver.
Rename the clock to the new name.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Michael Riesch <michael.riesch@wolfvision.net>
Link: https://lore.kernel.org/r/20220422072841.2206452-7-s.hauer@pengutronix.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This is the initial SoQuartz SoM device tree on a CM4IO carrier board.
This board outputs debug on uart2 and supports the following components:
Gigabit Ethernet
USB2 (OTG/Host shared)
PCIe 2.0 x1
HDMI (HDMI Port 0)
eDP (HDMI Port 1)
DSI (RPi compatible pinout)
CSI (RPi compatible pinout)
A/B/G/N WiFi
Bluetooth
SDMMC
eMMC
SPI NOR Flash (Not placed)
PI-40 compatible pin header
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Link: https://lore.kernel.org/r/20220429115252.2360496-7-pgwipeout@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add a device tree for the Pine64 Quartz64 Model B single board computer.
This board ouputs debug on uart2 and supports the following components:
Gigabit Ethernet
USB2 x2 (one port otg capable)
USB3
PCIe/SATA M2
HDMI
DSI (RPi compatible pinout)
CSI (RPi compatible pinout)
A/B/G/N WiFi
Bluetooth
SDMMC
eMMC
SPI Flash
PI-40 compatible pin header
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Link: https://lore.kernel.org/r/20220429115252.2360496-6-pgwipeout@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The pl330 DMA controller provides number of DMA channels and requests
through its registers, so duplicating this information (with a chance of
mistakes) in DTS is pointless. Additionally the DTS used always wrong
property names which causes DT schema check failures - the bindings
documented 'dma-channels' and 'dma-requests' properties without leading
hash sign.
Another reason is that the number of requests also does not seem right
(should be 8).
Link: https://lore.kernel.org/r/20220430121902.59895-5-krzysztof.kozlowski@linaro.org
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
One USB 2.0 host port on the Radxa ROCK3 Model A is connected to the
SoC via a hub. Introduce a voltage regulator to enable this USB hub.
Signed-off-by: Michael Riesch <michael.riesch@wolfvision.net>
Link: https://lore.kernel.org/r/20220425133502.405512-3-michael.riesch@wolfvision.net
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
PineNote has a USB Type-C port connected to the first USB 2.0 OTG PHY
and XHCI controller via a Willsemi WUSB3801 Type-C port controller.
Add support for it.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20220413035614.31045-3-samuel@sholland.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The RK3328 has an vdec device with dedicated iommu.
Describe the vdec device, the required power-domains
and enable the iommu in the devicetree.
Signed-off-by: Christopher Obbard <chris.obbard@collabora.com>
Link: https://lore.kernel.org/r/20220425184510.1138446-4-chris.obbard@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
All other rockchip devices which have vdec nodes do not
have an rk prefix. Remove the prefix from the (currently
unused) rkvdec_mmu node for consistency with other
devices.
Signed-off-by: Christopher Obbard <chris.obbard@collabora.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Link: https://lore.kernel.org/r/20220425184510.1138446-3-chris.obbard@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
From tegra186 onwards, memory controller support multiple channels.
During the error interrupts from memory controller, corresponding
channels need to be accessed for logging error info and clearing the
interrupt.
So add address and size of these channels in device tree node of
tegra186, tegra194 and tegra234 memory controller. Also add reg-names
for each of these reg items which are used by driver for mapping.
Signed-off-by: Ashish Mhetre <amhetre@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Enable i2c{0,1} on RZ/G2UL SMARC EVK by deleting respective
entries from board dts and adding pincontrol entries to the
soc-pinctrl dtsi. Also enable wm8978 audio codec.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220425170530.200921-8-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add the address space for SA3UL to the ranges property of the
cbass_main node.
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20220412075008.10553-1-j-choudhary@ti.com
Add USB2.0 host and device support by filling usb phy control,
phy, device and host stub nodes in RZ/G2UL SoC dtsi.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220425170530.200921-4-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
AM62 SoC has one instance of MCAN in main domain. However, its
corresponding CAN signals are not brought out through a transceiver, on the
SK board. Therefore, add the device tree node in the main dt file and set
the status to disabled in the SK board dts file.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20220418115802.5672-1-a-govindraju@ti.com
AM62 has 3 ECAP instances with 1 APWM each. Add DT nodes for the same.
Keep them disabled in am625-sk dts as these pins can be repurposed in
user exp connector.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Link: https://lore.kernel.org/r/20220419062902.196526-1-vigneshr@ti.com
Add nodes for I2C IO expander, OSPI Flash, Eth PHYs, SD and eMMC that
are present on AM625 SK board.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20220427072954.8821-3-vigneshr@ti.com
WL1837 module is connected to SDHCI0 in AM642 SK. Enable it here.
This will enable the WiFi functionaliy on the board.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Nikhil Devshatwar <nikhil.nd@ti.com>
Signed-off-by: Aparna M <a-m1@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20220414133612.13365-1-a-m1@ti.com
We found that (at least some versions of) the sci-fw set the base clock
rate for UARTs in the MCU domain to 96 MHz instead of the expected 48 MHz,
leading to incorrect baud rates when used from Linux.
As the 8250_omap driver will query the actual clock rate from the clk
driver when clock-frequency is unset, removing the incorrect property is
sufficient to fix the baud rate.
Fixes: 8abae9389b ("arm64: dts: ti: Add support for AM642 SoC")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20220419075157.189347-1-matthias.schiffer@ew.tq-group.com
Enable ASRC module usage on various Jetson Platforms. This can be plugged
into an audio path using ALSA mixer controls.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Asynchronous Sample Rate Converter (ASRC) is a client of AHUB and is
present on Tegra186 and later generations of Tegra SoC. Add this device
on the relevant SoC DTSI files.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add basic device-tree for the MT8195 Demo board. The
Demo board is made by MediaTek and has a MT8195 SoC,
associated with the MT6359 and MT6360 PMICs, and
the MT7921 connectivity chip.
The IOs available on that board are:
* 1 USB Type-C connector with DP aux mode support
* 1 USB Type-A connector
* 1 full size HDMI RX and 1 full size HDMI TX connector
* 1 uSD slot
* 40 pins header
* SPI interface header
* 1 M.2 slot
* 1 audio jack
* 1 micro-USB port for serial debug
* 2 connectors for DSI displays
* 3 connectors for CSI cameras
* 1 connector for a eDP panel
* 1 MMC storage
This commit adds basic support in order to be able to boot.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20220415150003.1793063-3-fparent@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
In mt8192 SoC, mmc driver dose not use the MSDC module to control
clock. It will read/write register to enable/disable clock. Also
there is no other device of mt8192 using MSDC controller.
We add mmc nodes for mt8192 SoC and remove the clock-controller in
dts for avoid a duplicate unit-address(11f60000) warning.
Signed-off-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20220407113703.26423-2-allen-kh.cheng@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The driver data of MT8183 and MT8173 are different.
The value of has_gamma for MT8173 is true while the value of MT8183 is
false. Therefore, the compatible of disp_aal for MT8183 is not suitable
for the compatible for MT8173.
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220411035843.19847-3-rex-bc.chen@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
MT6359 is the primary PMIC for MT8192.
Add PMIC MT6359 related node which is used for MT8192 platform.
Signed-off-by: Hui Liu <hui.liu@mediatek.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20220421012623.3446-2-hui.liu@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The power of encoder is not control by mediatek,larb, so we add
power domain to encoder nodes for mt8173 SoC.
Signed-off-by: Irui Wang <irui.wang@mediatek.com>
Signed-off-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Link: https://lore.kernel.org/r/20220421035111.7267-4-allen-kh.cheng@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
After adding device_link between the IOMMU consumer and smi,
the mediatek,larb is unnecessary now.
CC: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Signed-off-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Reviewed-by: Evan Green <evgreen@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220421035111.7267-3-allen-kh.cheng@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Align the name of thermal zone node to dtschema to fix warnings like:
arch/arm64/boot/dts/mediatek/mt8173-elm.dt.yaml:
thermal-zones: 'cpu_thermal' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-]{1,12}-thermal$', 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20210820081616.83674-2-krzysztof.kozlowski@canonical.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Align the name of operating-points node to dtschema to fix warnings like:
arch/arm64/boot/dts/mediatek/mt8173-elm.dt.yaml:
opp_table0: $nodename:0: 'opp_table0' does not match '^opp-table(-[a-z0-9]+)?$'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20210820081616.83674-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
dtschema expects PWM node name to be a generic "pwm". This also matches
Devicetree specification requirements about generic node names.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220214081916.162014-3-krzysztof.kozlowski@canonical.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
According to the device-tree binding document for PWM fans [0], the
PWM fan node name should be 'pwm-fan'. Update the PWM fan node name to
align with this.
[0] Documentation/devicetree/bindings/hwmon/pwm-fan.txt
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Adding CCPLEX cluster node to represent Tegra234 cpufreq. Tegra234 uses
some of the CRAB (Control Register Access Bus) registers for CPU
frequency requests. These registers are memory mapped to the
CCPLEX_MMCRAB_ARM region. In this node, mapping the range of MMCRAB
registers is required only for CPU frequency info.
Signed-off-by: Sumit Gupta <sumitg@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This reverts commit 1a67653de0, which caused a boot regression.
The behavior of the "drive-push-pull" in the kernel does not
match what the binding document describes. Revert Rob's patch
to make the DT match the kernel again, rather than the binding.
Link: https://lore.kernel.org/lkml/YlVAy95eF%2F9b1nmu@orome/
Reported-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
UART3 pins are available in the J1003 connector.
Add support for it.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The ROHM BD71847 PMIC has a 32.768 kHz clock.
Describe the PMIC clock to fix the following boot errors:
bd718xx-clk bd71847-clk.1.auto: No parent clk found
bd718xx-clk: probe of bd71847-clk.1.auto failed with error -22
Based on the same fix done for imx8mm-evk as per commit
a6a355ede5 ("arm64: dts: imx8mm-evk: Add 32.768 kHz clock to PMIC")
Fixes: 3e44dd0973 ("arm64: dts: imx8mn-ddr4-evk: Add rohm,bd71847 PMIC support")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add new board based on the Toradex Verdin iMX8M Mini SoM, the MX8Menlo.
The board is a compatible replacement for i.MX53 M53Menlo and features
USB, multiple UARTs, ethernet, LEDs, SD and eMMC.
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Francesco Dolcini <francesco.dolcini@toradex.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: NXP Linux Team <linux-imx@nxp.com>
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Some versions of the firmware for the sc7280-idp board FIFO mode
disabled and must thus use GPI DMA. Enable gpi_dma0 and gpi_dma1 to
allow this.
Co-developed-by: Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com>
Signed-off-by: Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220421115526.1828659-3-vkoul@kernel.org
The GENI I2C and SPI controllers may use the GPI DMA engine, define the
rx and tx channels for these controllers to enable this.
Co-developed-by: Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com>
Signed-off-by: Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220421115526.1828659-2-vkoul@kernel.org
Fix the following 'make dtbs_check' warning(s) by
using phy@ instead of lanes@:
arch/arm64/boot/dts/qcom/sm8450-hdk.dtb: phy@1c0f000: 'lanes@1c0e000'
does not match any of the regexes: '^phy@[0-9a-f]+$', 'pinctrl-[0-9]+'
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220418205509.1102109-5-bhupesh.sharma@linaro.org
Per DT spec node names should not have underscores (_) in them, so
change can_clock to can-clock.
Fixes: 5c44c564e4 ("arm64: dts: qcom: qrb5165-rb5: Add support for MCP2518FD")
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220421073502.1824089-1-vkoul@kernel.org
Add the Embedded USB Debugger(EUD) device tree node. The
node contains EUD base register region and EUD mode
manager register regions along with the interrupt entry.
Also add the typec connector node for EUD which is attached to
EUD node via port. EUD is also attached to DWC3 node via port.
Also add the role-switch property to dwc3 node.
Signed-off-by: Souradeep Chowdhury <quic_schowdhu@quicinc.com>
Link: https://lore.kernel.org/r/17a6127d1f0e4e3bac023dacf60a9ba93c1e21d1.1649235218.git.quic_schowdhu@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1. Cleanup: move aliases of board-related features to board in
Exynos850.
2. Add specific compatibles to Multi Core Timer to allow stricter DT
schema matching.
-----BEGIN PGP SIGNATURE-----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=mD92
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=NHCx
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt64-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/dt
Samsung DTS ARM64 changes for v5.19
1. Cleanup: move aliases of board-related features to board in
Exynos850.
2. Add specific compatibles to Multi Core Timer to allow stricter DT
schema matching.
* tag 'samsung-dt64-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
arm64: dts: tesla: add a specific compatible to MCT on FSD
arm64: dts: exynos: add a specific compatible to MCT
arm64: dts: exynos: move aliases to board in Exynos850
Link: https://lore.kernel.org/r/20220420072152.11696-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Enable the i2c5, spi4, spi18 and spi19 nodes which were tested on qrd
board along with related qup nodes and gpi_dma0
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220414101630.1189052-8-vkoul@kernel.org
qupv3_id_1 was missing iommus property which cause any dma transaction
to fail and board crash. So add the missing iommus.
Fixes: 5188049c9b ("arm64: dts: qcom: Add base SM8450 DTSI")
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220414101630.1189052-7-vkoul@kernel.org
qup1 has 7 SEs, I2C13 and I2C14 were already added so added the
remaining SEs (i2c and spi) along with pinconf for these SEs
Also add interconnect properties for I2C13 and I2C14
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220414101630.1189052-5-vkoul@kernel.org
qup0 has 7 SEs, with SE7 as uart and already added, so add the
remaining 6 SEs (i2c and spi) along with pinconf for these SEs
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220414101630.1189052-4-vkoul@kernel.org
qupv3_id_0 was missing iommus property which cause any dma transaction
to fail and board crash. So add the missing iommus.
While at it also add interconnect nodes for qup
Fixes: 5188049c9b ("arm64: dts: qcom: Add base SM8450 DTSI")
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220414101630.1189052-3-vkoul@kernel.org
GPI DMA can be used for DMA operations for QUP devices, so add the three
gpi_dma insances found in this SoC
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220414101630.1189052-2-vkoul@kernel.org
Some versions of the firmware for the SM8350 Hardware Development Kit
(HDK) has FIFO mode disabled for i2c13 and must thus use GPI DMA. Enable
&gpi_dma1 to allow this.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20220412215137.2385831-3-bjorn.andersson@linaro.org
The GENI I2C and SPI controllers may use the GPI DMA engine, define the
rx and tx channels for these controllers to enable this.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20220412215137.2385831-2-bjorn.andersson@linaro.org
Adding wakeup-source property for USB controller in SC7280.
This property is added to inform that the USB controller is
wake up capable and to conditionally power down the phy during
system suspend.
Signed-off-by: Sandeep Maheswaram <quic_c_sanm@quicinc.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1649704614-31518-7-git-send-email-quic_c_sanm@quicinc.com
Using node paths to extend or override a device tree node is error
prone. If there was a typo error, a new node will be created instead of
extending the existing node. This will lead to run-time errors that
could be hard to detect.
A mistyped label on the other hand, will cause a dtc compile error
(during build time). This also reduces the indentation making the code
easier to read.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220402192859.154977-2-krzysztof.kozlowski@linaro.org
Using node paths to extend or override a device tree node is error
prone. If there was a typo error, a new node will be created instead of
extending the existing node. This will lead to run-time errors that
could be hard to detect.
A mistyped label on the other hand, will cause a dtc compile error
(during build time). This also reduces the indentation making the code
easier to read.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220402192859.154977-1-krzysztof.kozlowski@linaro.org
Like the c630, the Poco F1 is also capable of using both antenna
channels for 2.4 and 5ghz wifi, however unlike the c630 only the first
channel is used for bluetooth. Similar to Oneplus 6.
Signed-off-by: Joel Selvaraj <jo@jsfamily.in>
Reviewed-by: Caleb Connolly <caleb@connolly.tech>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/BY5PR02MB7009E2566F9000F338432761D91F9@BY5PR02MB7009.namprd02.prod.outlook.com
The "qcom/sdm845/" path conflicts with db845c's firmware that are
present in the linux-firmware package. Xiaomi uses their own signed
firmware for Poco F1 and can't use the db845c's firmware. So let's
use "qcom/sdm845/beryllium/" to distinguish Poco F1's firmware files.
For easier handling and packaging, the mdt+bXX files are squashed
using Bjorn Andersson's pil-squasher tool from this link:
https://github.com/andersson/pil-squasher
Signed-off-by: Joel Selvaraj <jo@jsfamily.in>
Reviewed-by: Caleb Connolly <caleb@connolly.tech>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/BY5PR02MB700966DEE6F6044EBEB5B892D91F9@BY5PR02MB7009.namprd02.prod.outlook.com
Add thermal zones handled by tsens sensors. The definitions and the trip
points were taken from the downstream dts. For the CPU core thermal
sensors, the trip points were changed to follow the example of other
Qualcomm platforms.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220410234458.1739279-3-dmitry.baryshkov@linaro.org
The change adds description of two thermal sensor controllers found
on SM8450.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220410234458.1739279-2-dmitry.baryshkov@linaro.org
With the gcc driver now being more complete and describing clocks which
might not always be write-accessible to the OS, conservatively specify
all such clocks as protected in the SoC dts.
The board dts - or even user-supplied dts - can override this property
to reflect the actual configuration.
Signed-off-by: Michael Srba <michael.srba@seznam.cz>
Reviewed-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220411072156.24451-6-michael.srba@seznam.cz
The Gateworks GW7400 is an ARM based single board computer (SBC)
featuring:
- i.MX8M Plus SoC
- LPDDR4 DRAM
- eMMC FLASH
- Gateworks System Controller (GSC)
- QOS GbE
- Microchip GbE Switch
- Multiple multi-protocol RS232/RS485/RS422 Serial ports
- USB 3.0 Front panel connector
- onboard 802.11ac WiFi / BT
- 3x miniPCIe socket with PCIe and USB 2.0
- 1x M.2 B/A-E socket with PCIe, USB 3.0 and dual nano-SIM sockets
- off-board connectors for: MIPI DSI, MIPI CSI, SPI, GPIO, I2C
- Wide range DC power input
- Passive PoE
- 802.3at PoE
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Krzysztof Kozlowski <krzk+dt@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add a device tree for the 8MNANOD3L-EVK eval board which features an
IMX8MN SoC. It is similar to the 8MNANODLPD4-EVK eval board except it
has an IMX8MN UltraLite SoC and DDR3L memory. It esp. differs in the
PMIC configuration because the SoC has a smaller package and thus the
ARM core voltage is combined with the SoC voltage and the DDR voltage
is 1.35V for the DDR3L memory.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the missing 'uart-has-rtscts' property to UART's that have hardware
flow control capability.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the Video Processing Unit node for IMX8Q SoC.
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Signed-off-by: Shijie Qin <shijie.qin@nxp.com>
Signed-off-by: Zhou Peng <eagle.zhou@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The SDHC controller in the imx8mp has the same controller
as the imx8mm which supports HS400-ES. Change the compatible
fallback to imx8mm to enable it, but keep the imx7d-usdhc
to prevent breaking backwards compatibility.
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The SDHC controller in the imx8mn has the same controller
as the imx8mm which supports HS400-ES. Change the compatible
fallback to imx8mm to enable it, but keep the imx7d-usdhc
to prevent breaking backwards compatibility.
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Boolean properties in DT are present or not present and don't take a value.
A property such as 'foo = <0>;' evaluated to true. IOW, the value doesn't
matter.
It may have been intended that 0 values are false, but there is no change
in behavior with this patch.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Krzysztof Kozlowski <krzk+dt@kernel.org>
Cc: linux-arm-msm@vger.kernel.org
Link: https://lore.kernel.org/r/20220407225254.2178644-1-robh@kernel.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add Coresight Cross Trigger Interface(CTI) entries to the device tree
for all the Juno variants.
Link: https://lore.kernel.org/r/20220413214925.30359-1-mike.leach@linaro.org
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Mike Leach <mike.leach@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The SCMI power domain ID for all the coresight components is 8 while
the previous/older SCPI domain was 0. When adding SCMI variant, couple
of instances retained SCPI domain ID by mistake.
Fix the same by using the correct SCMI power domain ID of 8.
Link: https://lore.kernel.org/r/20220413093547.1699535-1-sudeep.holla@arm.com
Fixes: 96bb095486 ("arm64: dts: juno: Add separate SCMI variants")
Cc: Robin Murphy <robin.murphy@arm.com>
Reported-by: Mike Leach <Mike.Leach@arm.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Enable Ethernet{0,1} interfaces on RZ/G2UL SMARC EVK.
Ethernet0 pins are muxed with CAN0, CAN1, SSI1 and RSPI1 pins and Ethernet0
device selection is based on the SW1[3] switch position.
Set SW1[3] to position OFF for selecting CAN0, CAN1, SSI1 and RSPI1.
Set SW1[3] to position ON for selecting Ethernet0.
This patch disables Ethernet0 on RZ/G2UL SMARC platform by default.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220402081328.26292-8-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
RZ/G2UL SoM has both 64GB eMMC and microSD connected to SDHI0.
Both these interfaces are mutually exclusive and the SD0 device
selection is based on SW1[2] on SoM module.
Set SW1[2] to position OFF for selecting eMMC
Set SW1[2] to position ON for selecting microSD
This patch enables eMMC on RZ/G2UL SMARC platform by default.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220402081328.26292-7-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Enable the microSD card slot connected to SDHI1 on the RZ/G2UL SMARC
platform by removing the sdhi1 override which disabled it, and by adding
the necessary pinmux required for SDHI1.
This patch also adds gpios property to vccq_sdhi1 regulator.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220402081328.26292-6-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add scif0 and audio clk pins to soc pinctrl dtsi and drop deleting
the pinctrl-0 and pinctrl-names properties for scif0 node so that
we now actually make use of these properties for scif0.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220402081328.26292-3-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add basic support for RZ/G2UL SMARC EVK (based on R9A07G043U11):
- memory
- External input clock
- CPG
- DMA
- SCIF
It shares the same carrier board with RZ/G2L, but the pin mapping is
different. Disable the device nodes which are not tested and delete the
corresponding pinctrl definitions.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220412161314.13800-4-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add initial DTSI for RZ/G2UL SoC.
Both RZ/G2L and RZ/G2UL uses the same SMARC EVK. Therefore they share
the common dtsi (rz-smarc.dtsi) file. Place holders are added in
device nodes to avoid compilation errors for the devices which have
not been enabled yet on RZ/G2UL SoC.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220412161314.13800-3-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
On RZ/G2{L,LC} SoM module, gpio for power selection is connected to
P39_1 whereas on RZ/G2UL it is connected to P6_1. So move gpios property
of vccq_sdhi1 regulator from common dtsi to soc specific dtsi.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220401175427.19078-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
RSPI1 (SPI1) interface is available on PMOD0 connector (J1) on the
carrier board. This patch adds pinmux and spi1 nodes to the carrier
board dtsi file and drops deleting pinctl* properties from DTS file.
RSPI1 interface is tested by setting the macro SW_RSPI_CAN to 0.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220401145702.17954-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add device nodes for the SPI Multi I/O Bus Controllers (RPC-IF) on the
various R-Car Gen3 SoCs that do not have support for them yet in their
device trees (R-Car H3, M3-W, M3-W+, M3-N, E3, and D3).
Based on patches in the BSP by Valentine Barshak.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/3231749c7b63df1a2134daabe66446a3e0e5515b.1648548339.git.geert+renesas@glider.be
Rely on standard cci-control-port property to identify CCI port
reference.
Update mt7622 dts binding.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove regulator-always-on property where not necessary and mark regulators
that are not supposed to be voted active on boot with regulator-boot-on.
While at it, reorder the load properties to make it look more decent.
Reorder PMICs to fix a probe defer caused by messy dependencies and Linux's
inability to handle them (at least for now).
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220319174645.340379-12-konrad.dybcio@somainline.org
Make sure the necessary clocks are kept on after clk_cleanup (until MDSS
is properly handled by its own driver) and touch up the fb address to
prevent some weird shifting. It's still not perfect, but at least the
kernel log doesn't start a third deep into your screen..
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
[bjorn: Folded in change of framebuffer base address, from Konrad]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220319174645.340379-10-konrad.dybcio@somainline.org
Now that proper msm8992 support is in the driver, switch to
the new compatible.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Reviewed-by: Petr Vorel <petr.vorel@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220319174645.340379-7-konrad.dybcio@somainline.org
The phone seems to randomly crash when more than 1 CPU is enabled, which
is probably related to lack of some driver.
Restrict the device to only use a single core until this is solved.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220319174645.340379-4-konrad.dybcio@somainline.org
The sleep clock name expected by GCC is actually "sleep" and not
"sleep_clk". Fix the clock-names value for it to make sure it is
provided.
Fixes: 9204da57cd65 ("arm64: dts: qcom: msm8994: Provide missing "xo_board" and "sleep_clk" to GCC")
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Reviewed-by: Petr Vorel <petr.vorel@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220319174645.340379-2-konrad.dybcio@somainline.org
The number of interrupt cells for the mdss interrupt controller is 1,
meaning there should only be one cell for the interrupt number, not two.
Drop the second cell containing (unused) irq flags.
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Fixes: 7c1dffd471 ("arm64: dts: qcom: sm8250.dtsi: add display system nodes")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220302225411.2456001-5-dmitry.baryshkov@linaro.org
The number of interrupt cells for the mdss interrupt controller is 1,
meaning there should only be one cell for the interrupt number, not two.
Drop the second cell containing (unused) irq flags.
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Fixes: 08c2a076d1 ("arm64: dts: qcom: sdm845: Add dpu to sdm845 dts file")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220302225411.2456001-4-dmitry.baryshkov@linaro.org
The number of interrupt cells for the mdss interrupt controller is 1,
meaning there should only be one cell for the interrupt number, not two.
Drop the second cell containing (unused) irq flags.
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Fixes: ab29028439 ("arm64: dts: qcom: sdm660: Add required nodes for DSI1")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220302225411.2456001-3-dmitry.baryshkov@linaro.org
The number of interrupt cells for the mdss interrupt controller is 1,
meaning there should only be one cell for the interrupt number, not two.
Drop the second cell containing (unused) irq flags.
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Fixes: b52555d590 ("arm64: dts: qcom: sdm630: Add MDSS nodes")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220302225411.2456001-2-dmitry.baryshkov@linaro.org
The number of interrupt cells for the mdss interrupt controller is 1,
meaning there should only be one cell for the interrupt number, not two.
Drop the second cell containing (unused) irq flags.
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Fixes: 12d5403757 ("arm64: dts: qcom: msm8996: Add DSI0 nodes")
Fixes: 3a4547c1fc ("arm64: qcom: msm8996.dtsi: Add Display nodes")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220302225411.2456001-1-dmitry.baryshkov@linaro.org
Add device tree node for the first PCIe host found on the Qualcomm
SM8450 platform.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220301061500.2110569-3-dmitry.baryshkov@linaro.org
The huawei-g7 uses the msm8916-wcd-digital/analog audio codecs similar
to apq8016-sbc, so we can mostly copy paste it from there to make audio
work correctly. The main difference is the hphl-jack-type-normally-open
property, which is needed to avoid inverted audio jack detection.
Note that at least on my device the jack detection is not fully
reliable: sometimes headphones are detected as headsets (with
microphone). However, this is not a big problem for typical usage.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220410195113.13646-3-stephan@gerhold.net
The comment with installation instructions in the huawei-g7 device tree
is a bit misleading and does not describe the recommended installation
steps very well. The bootloader is actually not patched; to avoid all
trouble with the vendor bootloader it is easier to bypass it completely
by jumping to a custom bootloader (e.g. based on the open-source LK
released by Qualcomm).
To avoid confusion, simplify the comment to state only the problem
and then refer to the wiki article which contains detailed suggested
installation instructions. This will also make it easier to keep it
up to date with new developments in the future.
Fixes: 55056b2291 ("arm64: dts: qcom: msm8916: Add device tree for Huawei Ascend G7")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220410195113.13646-2-stephan@gerhold.net
Fix the following 'make dtbs_check' warning(s) by
using phy@ instead of lanes@ and by moving '#clock-cells' to
sub-node:
arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dt.yaml: ssphy@78000:
'lane@78200' does not match any of the regexes: '^phy@[0-9a-f]+$', 'pinctrl-[0-9]+'
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
[bjorn: s/clock-names/clock-cells/ per Shawn's feedback]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220228123019.382037-7-bhupesh.sharma@linaro.org
Fix the 'make dtbs_check' warning:
arch/arm64/boot/dts/qcom/sm8450-qrd.dt.yaml: phy@1d87000:
'lanes@1d87400' does not match any of the regexes: '^phy@[0-9a-f]+$', 'pinctrl-[0-9]+'
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220228123019.382037-6-bhupesh.sharma@linaro.org
Fix the 'make dtbs_check' warning:
arch/arm64/boot/dts/qcom/sc7280-idp.dt.yaml: phy@1c0e000:
'lanes@1c0e200' does not match any of the regexes: '^phy@[0-9a-f]+$', 'pinctrl-[0-9]+'
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220228123019.382037-5-bhupesh.sharma@linaro.org
The following properties are not supported and causing dtbs_check
warnings.
- vdda-phy-max-microamp
- vdda-pll-max-microamp
- vddp-ref-clk-max-microamp
- vddp-ref-clk-always-on
arch/arm64/boot/dts/qcom/msm8996-xiaomi-gemini.dt.yaml: phy@627000:
'vdda-phy-max-microamp', 'vddp-ref-clk-always-on', 'vddp-ref-clk-max-microamp'
do not match any of the regexes: '^phy@[0-9a-f]+$', 'pinctrl-[0-9]+'
Drop them from QMP PHY nodes for 'msm8996-xiaomi' dts.
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220228123019.382037-4-bhupesh.sharma@linaro.org
The BAM Data Multiplexer provides access to the network data channels
of modems integrated into many older Qualcomm SoCs, including MSM8916.
Add the nodes for the BAM DMA engine and BAM-DMUX to enable using WWAN
on smartphones/tablets based on MSM8916. This should work out of the box
with open-source WWAN userspace such as ModemManager.
The nodes are disabled by default to avoid loading unnecessary drivers
on devices that cannot use BAM-DMUX (e.g. DragonBoard 410c). However,
strictly speaking the nodes could be enabled by default since both the
bam_dma and bam_dmux driver will simply do nothing if the modem does
not announce any BAM-DMUX channels.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220228225400.146555-3-stephan@gerhold.net
Most of SoC device trees do not provide the thermal_zones label. Thus
stop depending on it and use the full path to the thermal zones nodes.
Fixes: 7a3544e5d4 ("arm64: dts: qcom: pmr735a: Add temp-alarm support")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220226205035.1826360-6-dmitry.baryshkov@linaro.org
Most of SoC device trees do not provide the thermal_zones label. Thus
stop depending on it and use the full path to the thermal zones nodes.
Fixes: 3795fe7d49 ("arm64: dts: qcom: pm8350c: Add temp-alarm support")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220226205035.1826360-5-dmitry.baryshkov@linaro.org
Add temp-alarm device tree node and a default configuration for the
corresponding thermal zone for this PMIC. Temperatures are based on
downstream values.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220226205035.1826360-4-dmitry.baryshkov@linaro.org
Add temp-alarm device tree node and a default configuration for the
corresponding thermal zone for this PMIC. Temperatures are based on
downstream values.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220226205035.1826360-3-dmitry.baryshkov@linaro.org
Add temp-alarm device tree node and a default configuration for the
corresponding thermal zone for this PMIC. Temperatures are based on
downstream values.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220226205035.1826360-2-dmitry.baryshkov@linaro.org
The OnePlus 5/5T both have an NXP PN553 which is supported by the
nxp-nci-i2c driver in mainline. It detects/reads NFC tags using
"nfctool" and with the NearD test scripts data can also be written
to be received by another device.
Signed-off-by: Jami Kettunen <jami.kettunen@somainline.org>
Reviewed-by: Caleb Connolly <caleb@connolly.tech>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220225215642.3916-1-jami.kettunen@somainline.org
Rename the edp_out label in the sc7280 platform to mdss_edp_out
so that the nodes related to mdss are all grouped together in
the board specific files.
Signed-off-by: Sankeerth Billakanti <quic_sbillaka@quicinc.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1647452154-16361-2-git-send-email-quic_sbillaka@quicinc.com
Enable the ethernet node, add the phy node and pinctrl for ethernet.
[bhsharma: Correct ethernet/rgmii related pinmuxs, specify multi-queues and
plug in the PHY interrupt for WOL]
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220325163537.1579969-3-bhupesh.sharma@linaro.org
Following sm8150/sm8250 update sdm845 capacity-dmips-mhz and
dynamic-power-coefficient based on the measurements [1], [2].
The energy model dynamic-power-coefficient values were calculated with
DPC = µW / MHz / V^2
for each OPP, and averaged across all OPPs within each cluster for the
final coefficient. Voltages were obtained from the qcom-cpufreq-hw
driver that reads voltages from the OSM LUT programmed into the SoC.
Normalized DMIPS/MHz capacity scale values for each CPU were calculated
from CoreMarks/MHz (CoreMark iterations per second per MHz), which
serves the same purpose. For each CPU, the final capacity-dmips-mhz
value is the C/MHz value of its maximum frequency normalized to
SCHED_CAPACITY_SCALE (1024) for the fastest CPU in the system.
For more details on measurement process see the commit message for the
commit 6aabed5526 ("arm64: dts: qcom: sm8250: Add CPU capacities and
energy model").
[1] https://github.com/kdrag0n/freqbench
[2] https://github.com/kdrag0n/freqbench/tree/master/results/sdm845/main
Cc: Danny Lin <danny@kdrag0n.dev>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220315141104.730235-1-dmitry.baryshkov@linaro.org
Several wakeup gpios supported by the Top Level Mode Multiplexer (TLMM)
block on sm8150 can be used as interrupt sources and these interrupts
are routed to the PDC interrupt controller.
So, specify PDC as the interrupt parent for the TLMM block.
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220226184028.111566-5-bhupesh.sharma@linaro.org
