Fix the issues seen with ethernet traffic getting stalled on SA8155p-ADP
board with default (or larger) mtu size of 1500 bytes, by disabling
multiple Tx and Rx queues for the stmmac IP block.
With the single queue setup, the ethernet traffic is stable,
wget / curl can work well on the board and no ethernet stall is
observed even when longer netperf / iperf3 test are run. Also
a performance of ~940 Mbits/sec is observed on the 1G link, so
there is no observable degradation in performance as well.
Fixes: c5cb42cc84 ("arm64: dts: qcom: sa8155p-adp: Enable ethernet node")
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220423195003.353150-1-bhupesh.sharma@linaro.org
Fix the IOMMU sid value for SDC2 controller, to ensure that no
ADMA error is observed when the microSD card is detected on the
SA8155p-ADP board.
Fixes: 876644c760 ("arm64: dts: qcom: sm8150: Add support for SDC2")
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220422210611.173842-1-bhupesh.sharma@linaro.org
Align DWC3 USB node names with DT schema ("usb" is expected) and correct
the unit addresses to match the "reg" property. This also implies
overriding nodes by label, instead of full path.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220504131923.214367-7-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
please pull the following:
- Krzysztof fixes the SPI NOR Device Tree node name to comply with the
dtschema
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEm+Rq3+YGJdiR9yuFh9CWnEQHBwQFAmJy6GYACgkQh9CWnEQH
BwQR6w//fHtYQAC+s/y7hTKhKi9ZPtLB9V60BwkzHbJR/NbTLQW5vn1AGQ2qcUTR
xA4RUoiIVqcrj3B4TXRMW+0AG5ULHIlGefYW945C9v17c/fi0+ylcTde9AlLRC/g
lOfXB82+1Q4yHr9qlAahtTT4SeC02BD/4yzlJ4jbF2JPdx3o71F5t+v2x4tko1Sh
EMfNNjZ3oLwaJLpAAvuVdIHjSyohK7BSWPndSi6iOhtZfvWYg00nWtCZp3jnjepm
CdUGEVlESbLpt2jtpEdc7mbrGcjZRSReNMz9J2ENjfyjguM4/ChYG99PaUSm11jV
LumvXu1TRALBUFEikdBizgKuy+Fy8mtw+k8GjUVxqrgDimebgNqrAOwklbXZcqPD
htGA/h/CYiMprUyYMZPNXIIA3f4+bTNpxM7wLrU6sBZoaObv6RAmSyYr4O2blas1
z9JAgHv5Bnr+0WU22HuHXVYgbkeyqOe2xcHi1rXm/HhhgrjjLdwkOLm/r29auJ7C
QghZsw41h5qMNfgiLvkIMivKCRilZg6rAdhmQ+Y8DPQD1lyIAM1D8Q52MiXPkmtt
Ld543fBtvrG39rv5pdR0PORoTMRFrSCY/M2KRYEMvRrs05nnAp2vU6ShOqXw/q3Q
rDA95mNzarLzxlVl80EOvHGdxcP16FlGwmUcdAZgmc9HXtBm+qE=
=igMx
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=KFF2
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.19/devicetree-arm64' of https://github.com/Broadcom/stblinux into arm/dt
This pull request contains Broadcom ARM64-based SoCs changes for 5.19,
please pull the following:
- Krzysztof fixes the SPI NOR Device Tree node name to comply with the
dtschema
* tag 'arm-soc/for-5.19/devicetree-arm64' of https://github.com/Broadcom/stblinux:
arm64: dts: broadcom: align SPI NOR node name with dtschema
Link: https://lore.kernel.org/r/20220504210942.1838248-3-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add node for dvi bridge and the endpoint nodes to
describe connection from
DSS => TI TFP410 DPI-to-DVI Bridge => HDMI connector.
Also add the required pinmux for HDMI hotplug and
powerdown
Signed-off-by: Rahul T R <r-ravikumar@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Aradhya Bhatia <a-bhatia1@ti.com>
Link: https://lore.kernel.org/r/20220505090709.9252-3-r-ravikumar@ti.com
Add the endpoint nodes to describe connection from
DSS => MHDP => DisplayPort connector.
Also add the required pinmux nodes for hotplug.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Rahul T R <r-ravikumar@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Aradhya Bhatia <a-bhatia1@ti.com>
Link: https://lore.kernel.org/r/20220429112639.13004-3-r-ravikumar@ti.com
Add DT nodes for DisplayPort and DisplayPort PHY. The DP is Cadence MHDP
8546 and the PHY is a Cadence Torrent PHY with TI WIZ wrapper.
Also add the required phy link nodes in the board dts files.
A slight irregularity in the bindings is the DPTX PHY register block,
which is in the MHDP IP, but is needed and mapped by the PHY.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Rahul T R <r-ravikumar@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Aradhya Bhatia <a-bhatia1@ti.com>
Link: https://lore.kernel.org/r/20220429112639.13004-2-r-ravikumar@ti.com
The main and bulk of the change is the addition of new platform
Arm corstone1000(both FVP and FPGA versions). Also, there are
addition of Coresight Cross Trigger Interface(CTI) support on Juno,
fix for incorrect SCMI power domain IDs, addition of virtio-rng
on FVP which is default disabled as it works only on latest versions
of the FVP model.
Other miscellanous changes include dropping of useless
'dma-channels/requests' properties and updating virtio device
node names as per dtschema.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEunHlEgbzHrJD3ZPhAEG6vDF+4pgFAmJyPcUACgkQAEG6vDF+
4pizDw/+NzmnScLZFzwXKi8LqKIuC+JlDf+mvWGlidjjz2c1X4Mf45AKPpKvRQmc
PyvVKB7t6azo9xHcgS43J7+DOFOziqjY/+RJhiQ7YS8L/SSSuaNDyAO3EpWpIo85
c2QL9sFsiVPqQFmF+E4cLh96gF97xi2QfB2420E5m7feLzCgHQZYYWijhGVlZR5L
nsoXLDU/HK9MTts3q9jyen3gA2nBE7NGuU2SacehJNXoHCd+T0W6AQgYWIWzWa+X
eq/PbbnFCguFyzNRncbnxzCVOXeg0FS1zTPOtJFNHioG6FnIEqg4VEF9g2hdtnTZ
CGEtu4vvVsSKxIr7s2d/vfqlYpOpxwVkJl3XgNcqLXTgk4tHWODW7Rl7RTXwT3hT
mgh0j272/4gm+iTDYI+YmanQsEKP/VQiMGXDVTX43da2rgFVXUMU/XT1EHy7Ef0P
iULL5sqcA0q9Y895AV6aeMXZdQl9ZHYYgLxQLPecMVt+dMfde1LxaRssH3YQ+aLN
u0ZO/SOYRXqe1AbJvgC2xKPH6URmNAHHg6urVsOPI14Zj+q+zdz7M2/Ii1cu6o5O
EvISCqoNU0Wazcnfg6Khp6MwnPxKVIHl0w3C0Z4qZjVIzzSF0VTomy1W3FJHEZuf
9HSB0BopmOM8FQzAOJnHYjHIXT7jhhjACmapdi4U1d+XGqw1ih4=
=dlOE
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=o+6w
-----END PGP SIGNATURE-----
Merge tag 'juno-updates-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/dt
Arm FVP/Juno device tree updates for v5.19
The main and bulk of the change is the addition of new platform
Arm corstone1000(both FVP and FPGA versions). Also, there are
addition of Coresight Cross Trigger Interface(CTI) support on Juno,
fix for incorrect SCMI power domain IDs, addition of virtio-rng
on FVP which is default disabled as it works only on latest versions
of the FVP model.
Other miscellanous changes include dropping of useless
'dma-channels/requests' properties and updating virtio device
node names as per dtschema.
* tag 'juno-updates-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
arm64: dts: juno: Drop useless 'dma-channels/requests' properties
arm64: dts: fvp: Align virtio device node names with dtschema
arm64: dts: fvp: Add virtio-rng support
arm64: dts: Add Arm corstone1000 platform support
dt-bindings: Add Arm corstone1000 platform
arm64: dts: juno: add CTI entries to device tree
arm64: dts: juno: Fix SCMI power domain IDs for ETF and CS funnel
Link: https://lore.kernel.org/r/20220504112917.3492009-1-sudeep.holla@arm.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The i.MX8M Plus has the same PWM IP as i.MX6 / i.MX7. This IP
and the driver supporting pwm polarity inversion. Switch CPU
device tree fragment to use 3 pwm-cells.
Tested on MBa8MPxL mainboard.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX8M Nano has the same PWM IP as i.MX6 / i.MX7. This IP
and the driver supporting pwm polarity inversion. Switch CPU
device tree fragment to use 3 pwm-cells.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX8M Mini has the same PWM IP as i.MX6 / i.MX7. This IP
and the driver supporting pwm polarity inversion. Switch CPU
device tree fragment to use 3 pwm-cells and correct board
device trees.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX8MQ has the same PWM IP as i.MX6 / i.MX7. This IP and the driver
supporting pwm polarity inversion. Switch CPU device tree fragment to
use 3 pwm-cells and correct board device trees.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Remove the unnecessary cpu_alert0 and cpu_crit0 TMU node overrides as
these are added dynamically by boot firmware based on CPU temperature
grade.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Define the missing clock-names property for the pcie_phy required by
the fsl,imx8-pcie-phy dt bindings.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Update the pcie bindings to the correct dt bindings:
pcie_phy:
- use pcie0_refclk
- add required clock-names
pcie:
- remove pcie_phy clock as it comes from phy driver
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Reduce the interrupt-map-mask of the external interrupt controller to
0xf to align with the devicetree schema.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is a header for a DB9 serial port, but any attempts to use
hardware handshaking fail. Enable RTS and CTS pin muxing and enable
handshaking in the uart node.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is a header for a DB9 serial port, but any attempts to use
hardware handshaking fail. Enable RTS and CTS pin muxing and enable
handshaking in the uart node.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The I2C2 has SMBus device SMSC USB2514Bi connected to it, the device is
capable of up to 100 kHz operation. Reduce the bus frequency to 100 kHz
to guarantee this I2C device can work correctly.
Fixes: 583f24ae42 ("arm64: dts: imx8mm: Add support for Data Modul i.MX8M Mini eDM SBC")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: NXP Linux Team <linux-imx@nxp.com>
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The USB2 port has USB Hub permanently connected to it, disable OC
to avoid getting false OC indication.
Fixes: 583f24ae42 ("arm64: dts: imx8mm: Add support for Data Modul i.MX8M Mini eDM SBC")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: NXP Linux Team <linux-imx@nxp.com>
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The CPLD on MX8Menlo board is used to operate custom hardware,
the CPLD content is compatible with previous M53Menlo CPLD,
add the bindings.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: devicetree@vger.kernel.org
To: linux-arm-kernel@lists.infradead.org
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The usage of the 'fsl,uart-has-rtscts' property is deprecated.
Use the standard 'uart-has-rtscts' instead.
Cc: Heiko Thiery <heiko.thiery@gmail.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-By: Heiko Thiery <heiko.thiery@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The usage of the 'fsl,uart-has-rtscts' property is deprecated.
Use the standard 'uart-has-rtscts' instead.
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add a DT node for the MEDIA_BLK_CTRL, which provides power domains for
the camera and display devices.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the power domains related to the MEDIAMIX to the GPC.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds the GPC and HSIO blk-ctrl nodes providing power control for
the high-speed (USB and PCIe) IOs.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Genaral features:
- LCD 7" C.Touch
- microSD slot
- Ethernet 1Gb
- Wifi/BT
- 2x LVDS Full HD interfaces
- 3x USB 2.0
- 1x USB 3.0
- HDMI Out
- Plus PCIe
- MIPI CSI
- 2x CAN
- Audio Out
i.Core MX8M Plus is an EDIMM SoM based on NXP i.MX8M Plus from Engicam.
i.Core MX8M Plus needs to mount on top of this Evaluation board for
creating complete i.Core MX8M Plus EDIMM2.2 Starter Kit.
Add support for it.
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Signed-off-by: Matteo Lisi <matteo.lisi@engicam.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.Core MX8M Plus is an EDIMM SoM based on NXP i.MX8M Plus
from Engicam.
General features:
- NXP i.MX8M Plus
- Up to 4GB LDDR4
- 8 eMMC
- Gigabit Ethernet
- USB 3.0, 2.0 Host/OTG
- PCIe 3.0 interface
- I2S
- LVDS
- rest of i.MX8M Plus features
i.Core MX8M Plus needs to mount on top of Engicam baseboards
for creating complete platform solutions.
Add support for it.
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Signed-off-by: Matteo Lisi <matteo.lisi@engicam.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Update the node name to be align with updated DT binding. But be
noted that u-boot for ls1088a used the ifc node name to disable ifc-nor
node when the SoC is configured to use QSPI. The u-boot has been
updated to use the latest name but the change could break
compatibility with older u-boot for ls1088a.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The binding of ifc device has been updated. Update dts to match
accordingly.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Commit 4782c0a5dd ("clk: tegra: Don't deassert reset on enabling
clocks") removed deassertion of reset lines when enabling peripheral
clocks. This breaks the initialization of the DFLL driver which relied
on this behaviour.
In order to be able to fix this, add the corresponding reset to the DT.
Tested on Google Pixel C.
Cc: stable@vger.kernel.org
Fixes: 4782c0a5dd ("clk: tegra: Don't deassert reset on enabling clocks")
Signed-off-by: Diogo Ivo <diogo.ivo@tecnico.ulisboa.pt>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The pl330 DMA controller provides number of DMA channels and requests
through its registers, so duplicating this information (with a chance of
mistakes) in DTS is pointless. Additionally the DTS used always wrong
property names which causes DT schema check failures - the bindings
documented 'dma-channels' and 'dma-requests' properties without leading
hash sign.
Reported-by: Rob Herring <robh@kernel.org>
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220430121902.59895-6-krzysztof.kozlowski@linaro.org
The pl330 DMA controller provides number of DMA channels and requests
through its registers, so duplicating this information (with a chance of
mistakes) in DTS is pointless. Additionally the DTS used always wrong
property names which causes DT schema check failures - the bindings
documented 'dma-channels' and 'dma-requests' properties without leading
hash sign.
Reported-by: Rob Herring <robh@kernel.org>
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220430121902.59895-4-krzysztof.kozlowski@linaro.org
The pl330 DMA controller provides number of DMA channels and requests
through its registers, so duplicating this information (with a chance of
mistakes) in DTS is pointless. Additionally the DTS used always wrong
property names which causes DT schema check failures - the bindings
documented 'dma-channels' and 'dma-requests' properties without leading
hash sign.
Reported-by: Rob Herring <robh@kernel.org>
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220430121902.59895-10-krzysztof.kozlowski@linaro.org
The pl330 DMA controller provides number of DMA channels and requests
through its registers, so duplicating this information (with a chance of
mistakes) in DTS is pointless. Additionally the DTS used always wrong
property names which causes DT schema check failures - the bindings
documented 'dma-channels' and 'dma-requests' properties without leading
hash sign.
Reported-by: Rob Herring <robh@kernel.org>
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220430121902.59895-9-krzysztof.kozlowski@linaro.org
The external oscillator - XTCXO - is an input to the SoC. It is defined
in the Exynos Auto v9 SoC DTSI, because all boards will provide it and
clock controller bindings expect it, however the actual frequency of the
clock should be determined by the board.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Chanho Park <chanho61.park@samsung.com>
Link: https://lore.kernel.org/r/20220503092631.174713-1-krzysztof.kozlowski@linaro.org
WLAN rail was leaking power during RBSC/sleep even after turning BT off.
Change active and sleep pinctrl configurations to handle same.
Signed-off-by: Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1650556567-4995-3-git-send-email-quic_vnivarth@quicinc.com
WLAN rail was leaking power during RBSC/sleep even after turning BT off.
Change active and sleep pinctrl configurations to handle same.
Signed-off-by: Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1650556567-4995-2-git-send-email-quic_vnivarth@quicinc.com
This device node is unused now that we've removed the driver that
consumed it in the kernel. Drop the unused node to save some space.
Cc: Alex Elder <elder@linaro.org>
Cc: Taniya Das <quic_tdas@quicinc.com>
Cc: Mike Tipton <quic_mdtipton@quicinc.com>
Cc: Georgi Djakov <djakov@kernel.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Acked-by: Georgi Djakov <djakov@kernel.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220415005828.1980055-1-swboyd@chromium.org
Allwinner A64 SoC has separate supplies for PC, PD, PE, PG and PL.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220430191009.73946-1-harald@ccbib.org
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmJu9FYeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGAyEH/16xtJSpLmLwrQzG
o+4ToQxSQ+/9UHyu0RTEvHg2THm9/8emtIuYyc/5FgdoWctcSa3AaDcveWmuWmkS
KYcdhfJsaEqjNHS3OPYXN84fmo9Hel7263shu5+IYmP/sN0DfQp6UWTryX1q4B3Q
4Pdutkuq63Uwd8nBZ5LXQBumaBrmkkuMgWEdT4+6FOo1mPzwdIGBxCuz1UsNNl5k
chLWxkQfe2eqgWbYJrgCQfrVdORXVtoU2fGilZUNrHRVGkkldXkkz5clJfapyZD3
odmZCEbrE4GPKgZwCmDERMfD1hzhZDtYKiHfOQ506szH5ykJjPBcOjHed7dA60eB
J3+wdek=
=39Ca
-----END PGP SIGNATURE-----
Merge 5.18-rc5 into usb-next
We need the USB fixes in here, and this resolves a merge issue in
drivers/usb/dwc3/drd.c
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- ADC, SDHI, CAN-FD, I2C, QSPI, timer, watchdog, sound, USB, SPI, GPU,
cpufreq, and thermal support for the RZ/V2L SoC, and the RZ/V2L
SMARC EVK development board,
- USB, I2C, Audio, NOR Flash, timer, SPI support for RZ/G2LC SMARC EVK
development board,
- Can-FD support for the R-Car M30W+ and V3U SoCs, and the Falcon
development board,
- I2C and GPIO support for the R-Car S4-8 SoC,
- I2C EEPROM support for the Falcon development board,
- SPI Multi I/O Bus Controller (RPC-IF) support for the R-Car H3,
M3-W(+), M3-N, E3, and D3 SoCs,
- RPC HyperFlash support for the Draak, Ebisu, Salvator-X(S), and ULCB
development boards,
- Initial support (UART, DMAC, pin control, SDHI, eMMC, Ethernet) for
the RZ/G2UL SoC, and the RZ/G2UL SMARC EVK development board,
- Miscellaneous fixes and improvements.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCYmJ+7gAKCRCKwlD9ZEnx
cE5hAQDebyQdMMpgRgOC4ES3leIRrMJSmOAjrQcQjrTUJ6WYNgD9Gj8USqudA/By
Toz6dahFUSI0MDbgqnBjiqMGbEnbNww=
=xap2
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=SiTm
-----END PGP SIGNATURE-----
Merge tag 'renesas-arm-dt-for-v5.19-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/dt
Renesas ARM DT updates for v5.19
- ADC, SDHI, CAN-FD, I2C, QSPI, timer, watchdog, sound, USB, SPI, GPU,
cpufreq, and thermal support for the RZ/V2L SoC, and the RZ/V2L
SMARC EVK development board,
- USB, I2C, Audio, NOR Flash, timer, SPI support for RZ/G2LC SMARC EVK
development board,
- Can-FD support for the R-Car M30W+ and V3U SoCs, and the Falcon
development board,
- I2C and GPIO support for the R-Car S4-8 SoC,
- I2C EEPROM support for the Falcon development board,
- SPI Multi I/O Bus Controller (RPC-IF) support for the R-Car H3,
M3-W(+), M3-N, E3, and D3 SoCs,
- RPC HyperFlash support for the Draak, Ebisu, Salvator-X(S), and ULCB
development boards,
- Initial support (UART, DMAC, pin control, SDHI, eMMC, Ethernet) for
the RZ/G2UL SoC, and the RZ/G2UL SMARC EVK development board,
- Miscellaneous fixes and improvements.
* tag 'renesas-arm-dt-for-v5.19-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel: (55 commits)
ARM: dts: r9a06g032: Drop "arm,cortex-a7-timer" from timer node
arm64: dts: renesas: r8a779f0: Add GPIO nodes
arm64: dts: renesas: rzg2ul-smarc-som: Enable Ethernet on SMARC platform
arm64: dts: renesas: rzg2ul-smarc-som: Enable eMMC on SMARC platform
arm64: dts: renesas: rzg2ul-smarc: Enable microSD on SMARC platform
arm64: dts: renesas: r9a07g043: Add GbEthernet nodes
arm64: dts: renesas: r9a07g043: Add SDHI nodes
arm64: dts: renesas: rzg2ul-smarc: Add scif0 and audio clk pins
arm64: dts: renesas: r9a07g043: Fillup the pinctrl stub node
arm64: dts: renesas: Add initial device tree for RZ/G2UL Type-1 SMARC EVK
arm64: dts: renesas: Add initial DTSI for RZ/G2UL SoC
arm64: dts: renesas: rzg2l-smarc: Move gpios property of vccq_sdhi1 from common dtsi
arm64: dts: renesas: rzg2lc-smarc: Enable RSPI1 on carrier board
arm64: dts: renesas: ulcb: Add RPC HyperFlash device node
arm64: dts: renesas: salvator-common: Add RPC HyperFlash device node
arm64: dts: renesas: ebisu: Add RPC HyperFlash device node
arm64: dts: renesas: draak: Add RPC HyperFlash device node
arm64: dts: renesas: rcar-gen3: Add RPC device nodes
arm64: dts: renesas: rcar-gen4: Add interrupt properties to watchdog nodes
arm64: dts: renesas: rzg2: Add interrupt properties to watchdog nodes
...
Link: https://lore.kernel.org/r/cover.1650638505.git.geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The reference clock for the HDMI controller has been renamed to 'ref',
the previous 'vpll' name is only left for compatibility in the driver.
Rename the clock to the new name.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Michael Riesch <michael.riesch@wolfvision.net>
Link: https://lore.kernel.org/r/20220422072841.2206452-7-s.hauer@pengutronix.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This is the initial SoQuartz SoM device tree on a CM4IO carrier board.
This board outputs debug on uart2 and supports the following components:
Gigabit Ethernet
USB2 (OTG/Host shared)
PCIe 2.0 x1
HDMI (HDMI Port 0)
eDP (HDMI Port 1)
DSI (RPi compatible pinout)
CSI (RPi compatible pinout)
A/B/G/N WiFi
Bluetooth
SDMMC
eMMC
SPI NOR Flash (Not placed)
PI-40 compatible pin header
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Link: https://lore.kernel.org/r/20220429115252.2360496-7-pgwipeout@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add a device tree for the Pine64 Quartz64 Model B single board computer.
This board ouputs debug on uart2 and supports the following components:
Gigabit Ethernet
USB2 x2 (one port otg capable)
USB3
PCIe/SATA M2
HDMI
DSI (RPi compatible pinout)
CSI (RPi compatible pinout)
A/B/G/N WiFi
Bluetooth
SDMMC
eMMC
SPI Flash
PI-40 compatible pin header
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Link: https://lore.kernel.org/r/20220429115252.2360496-6-pgwipeout@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The pl330 DMA controller provides number of DMA channels and requests
through its registers, so duplicating this information (with a chance of
mistakes) in DTS is pointless. Additionally the DTS used always wrong
property names which causes DT schema check failures - the bindings
documented 'dma-channels' and 'dma-requests' properties without leading
hash sign.
Another reason is that the number of requests also does not seem right
(should be 8).
Link: https://lore.kernel.org/r/20220430121902.59895-5-krzysztof.kozlowski@linaro.org
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
One USB 2.0 host port on the Radxa ROCK3 Model A is connected to the
SoC via a hub. Introduce a voltage regulator to enable this USB hub.
Signed-off-by: Michael Riesch <michael.riesch@wolfvision.net>
Link: https://lore.kernel.org/r/20220425133502.405512-3-michael.riesch@wolfvision.net
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
PineNote has a USB Type-C port connected to the first USB 2.0 OTG PHY
and XHCI controller via a Willsemi WUSB3801 Type-C port controller.
Add support for it.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20220413035614.31045-3-samuel@sholland.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The RK3328 has an vdec device with dedicated iommu.
Describe the vdec device, the required power-domains
and enable the iommu in the devicetree.
Signed-off-by: Christopher Obbard <chris.obbard@collabora.com>
Link: https://lore.kernel.org/r/20220425184510.1138446-4-chris.obbard@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
All other rockchip devices which have vdec nodes do not
have an rk prefix. Remove the prefix from the (currently
unused) rkvdec_mmu node for consistency with other
devices.
Signed-off-by: Christopher Obbard <chris.obbard@collabora.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Link: https://lore.kernel.org/r/20220425184510.1138446-3-chris.obbard@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
From tegra186 onwards, memory controller support multiple channels.
During the error interrupts from memory controller, corresponding
channels need to be accessed for logging error info and clearing the
interrupt.
So add address and size of these channels in device tree node of
tegra186, tegra194 and tegra234 memory controller. Also add reg-names
for each of these reg items which are used by driver for mapping.
Signed-off-by: Ashish Mhetre <amhetre@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Enable i2c{0,1} on RZ/G2UL SMARC EVK by deleting respective
entries from board dts and adding pincontrol entries to the
soc-pinctrl dtsi. Also enable wm8978 audio codec.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220425170530.200921-8-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add the address space for SA3UL to the ranges property of the
cbass_main node.
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20220412075008.10553-1-j-choudhary@ti.com
Add USB2.0 host and device support by filling usb phy control,
phy, device and host stub nodes in RZ/G2UL SoC dtsi.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220425170530.200921-4-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
AM62 SoC has one instance of MCAN in main domain. However, its
corresponding CAN signals are not brought out through a transceiver, on the
SK board. Therefore, add the device tree node in the main dt file and set
the status to disabled in the SK board dts file.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20220418115802.5672-1-a-govindraju@ti.com
AM62 has 3 ECAP instances with 1 APWM each. Add DT nodes for the same.
Keep them disabled in am625-sk dts as these pins can be repurposed in
user exp connector.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Link: https://lore.kernel.org/r/20220419062902.196526-1-vigneshr@ti.com
Add nodes for I2C IO expander, OSPI Flash, Eth PHYs, SD and eMMC that
are present on AM625 SK board.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20220427072954.8821-3-vigneshr@ti.com
WL1837 module is connected to SDHCI0 in AM642 SK. Enable it here.
This will enable the WiFi functionaliy on the board.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Nikhil Devshatwar <nikhil.nd@ti.com>
Signed-off-by: Aparna M <a-m1@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20220414133612.13365-1-a-m1@ti.com
We found that (at least some versions of) the sci-fw set the base clock
rate for UARTs in the MCU domain to 96 MHz instead of the expected 48 MHz,
leading to incorrect baud rates when used from Linux.
As the 8250_omap driver will query the actual clock rate from the clk
driver when clock-frequency is unset, removing the incorrect property is
sufficient to fix the baud rate.
Fixes: 8abae9389b ("arm64: dts: ti: Add support for AM642 SoC")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20220419075157.189347-1-matthias.schiffer@ew.tq-group.com
Enable ASRC module usage on various Jetson Platforms. This can be plugged
into an audio path using ALSA mixer controls.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Asynchronous Sample Rate Converter (ASRC) is a client of AHUB and is
present on Tegra186 and later generations of Tegra SoC. Add this device
on the relevant SoC DTSI files.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add basic device-tree for the MT8195 Demo board. The
Demo board is made by MediaTek and has a MT8195 SoC,
associated with the MT6359 and MT6360 PMICs, and
the MT7921 connectivity chip.
The IOs available on that board are:
* 1 USB Type-C connector with DP aux mode support
* 1 USB Type-A connector
* 1 full size HDMI RX and 1 full size HDMI TX connector
* 1 uSD slot
* 40 pins header
* SPI interface header
* 1 M.2 slot
* 1 audio jack
* 1 micro-USB port for serial debug
* 2 connectors for DSI displays
* 3 connectors for CSI cameras
* 1 connector for a eDP panel
* 1 MMC storage
This commit adds basic support in order to be able to boot.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20220415150003.1793063-3-fparent@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
In mt8192 SoC, mmc driver dose not use the MSDC module to control
clock. It will read/write register to enable/disable clock. Also
there is no other device of mt8192 using MSDC controller.
We add mmc nodes for mt8192 SoC and remove the clock-controller in
dts for avoid a duplicate unit-address(11f60000) warning.
Signed-off-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20220407113703.26423-2-allen-kh.cheng@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The driver data of MT8183 and MT8173 are different.
The value of has_gamma for MT8173 is true while the value of MT8183 is
false. Therefore, the compatible of disp_aal for MT8183 is not suitable
for the compatible for MT8173.
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220411035843.19847-3-rex-bc.chen@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
MT6359 is the primary PMIC for MT8192.
Add PMIC MT6359 related node which is used for MT8192 platform.
Signed-off-by: Hui Liu <hui.liu@mediatek.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20220421012623.3446-2-hui.liu@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The power of encoder is not control by mediatek,larb, so we add
power domain to encoder nodes for mt8173 SoC.
Signed-off-by: Irui Wang <irui.wang@mediatek.com>
Signed-off-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Link: https://lore.kernel.org/r/20220421035111.7267-4-allen-kh.cheng@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
After adding device_link between the IOMMU consumer and smi,
the mediatek,larb is unnecessary now.
CC: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Signed-off-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Reviewed-by: Evan Green <evgreen@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220421035111.7267-3-allen-kh.cheng@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Align the name of thermal zone node to dtschema to fix warnings like:
arch/arm64/boot/dts/mediatek/mt8173-elm.dt.yaml:
thermal-zones: 'cpu_thermal' does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-]{1,12}-thermal$', 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20210820081616.83674-2-krzysztof.kozlowski@canonical.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Align the name of operating-points node to dtschema to fix warnings like:
arch/arm64/boot/dts/mediatek/mt8173-elm.dt.yaml:
opp_table0: $nodename:0: 'opp_table0' does not match '^opp-table(-[a-z0-9]+)?$'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20210820081616.83674-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
dtschema expects PWM node name to be a generic "pwm". This also matches
Devicetree specification requirements about generic node names.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220214081916.162014-3-krzysztof.kozlowski@canonical.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
According to the device-tree binding document for PWM fans [0], the
PWM fan node name should be 'pwm-fan'. Update the PWM fan node name to
align with this.
[0] Documentation/devicetree/bindings/hwmon/pwm-fan.txt
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Adding CCPLEX cluster node to represent Tegra234 cpufreq. Tegra234 uses
some of the CRAB (Control Register Access Bus) registers for CPU
frequency requests. These registers are memory mapped to the
CCPLEX_MMCRAB_ARM region. In this node, mapping the range of MMCRAB
registers is required only for CPU frequency info.
Signed-off-by: Sumit Gupta <sumitg@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This reverts commit 1a67653de0, which caused a boot regression.
The behavior of the "drive-push-pull" in the kernel does not
match what the binding document describes. Revert Rob's patch
to make the DT match the kernel again, rather than the binding.
Link: https://lore.kernel.org/lkml/YlVAy95eF%2F9b1nmu@orome/
Reported-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
UART3 pins are available in the J1003 connector.
Add support for it.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The ROHM BD71847 PMIC has a 32.768 kHz clock.
Describe the PMIC clock to fix the following boot errors:
bd718xx-clk bd71847-clk.1.auto: No parent clk found
bd718xx-clk: probe of bd71847-clk.1.auto failed with error -22
Based on the same fix done for imx8mm-evk as per commit
a6a355ede5 ("arm64: dts: imx8mm-evk: Add 32.768 kHz clock to PMIC")
Fixes: 3e44dd0973 ("arm64: dts: imx8mn-ddr4-evk: Add rohm,bd71847 PMIC support")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add new board based on the Toradex Verdin iMX8M Mini SoM, the MX8Menlo.
The board is a compatible replacement for i.MX53 M53Menlo and features
USB, multiple UARTs, ethernet, LEDs, SD and eMMC.
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Francesco Dolcini <francesco.dolcini@toradex.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: NXP Linux Team <linux-imx@nxp.com>
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Some versions of the firmware for the sc7280-idp board FIFO mode
disabled and must thus use GPI DMA. Enable gpi_dma0 and gpi_dma1 to
allow this.
Co-developed-by: Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com>
Signed-off-by: Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220421115526.1828659-3-vkoul@kernel.org
The GENI I2C and SPI controllers may use the GPI DMA engine, define the
rx and tx channels for these controllers to enable this.
Co-developed-by: Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com>
Signed-off-by: Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220421115526.1828659-2-vkoul@kernel.org
Fix the following 'make dtbs_check' warning(s) by
using phy@ instead of lanes@:
arch/arm64/boot/dts/qcom/sm8450-hdk.dtb: phy@1c0f000: 'lanes@1c0e000'
does not match any of the regexes: '^phy@[0-9a-f]+$', 'pinctrl-[0-9]+'
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220418205509.1102109-5-bhupesh.sharma@linaro.org
Per DT spec node names should not have underscores (_) in them, so
change can_clock to can-clock.
Fixes: 5c44c564e4 ("arm64: dts: qcom: qrb5165-rb5: Add support for MCP2518FD")
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220421073502.1824089-1-vkoul@kernel.org
Add the Embedded USB Debugger(EUD) device tree node. The
node contains EUD base register region and EUD mode
manager register regions along with the interrupt entry.
Also add the typec connector node for EUD which is attached to
EUD node via port. EUD is also attached to DWC3 node via port.
Also add the role-switch property to dwc3 node.
Signed-off-by: Souradeep Chowdhury <quic_schowdhu@quicinc.com>
Link: https://lore.kernel.org/r/17a6127d1f0e4e3bac023dacf60a9ba93c1e21d1.1649235218.git.quic_schowdhu@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1. Cleanup: move aliases of board-related features to board in
Exynos850.
2. Add specific compatibles to Multi Core Timer to allow stricter DT
schema matching.
-----BEGIN PGP SIGNATURE-----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=mD92
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=NHCx
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt64-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/dt
Samsung DTS ARM64 changes for v5.19
1. Cleanup: move aliases of board-related features to board in
Exynos850.
2. Add specific compatibles to Multi Core Timer to allow stricter DT
schema matching.
* tag 'samsung-dt64-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
arm64: dts: tesla: add a specific compatible to MCT on FSD
arm64: dts: exynos: add a specific compatible to MCT
arm64: dts: exynos: move aliases to board in Exynos850
Link: https://lore.kernel.org/r/20220420072152.11696-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Enable the i2c5, spi4, spi18 and spi19 nodes which were tested on qrd
board along with related qup nodes and gpi_dma0
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220414101630.1189052-8-vkoul@kernel.org
qupv3_id_1 was missing iommus property which cause any dma transaction
to fail and board crash. So add the missing iommus.
Fixes: 5188049c9b ("arm64: dts: qcom: Add base SM8450 DTSI")
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220414101630.1189052-7-vkoul@kernel.org
qup1 has 7 SEs, I2C13 and I2C14 were already added so added the
remaining SEs (i2c and spi) along with pinconf for these SEs
Also add interconnect properties for I2C13 and I2C14
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220414101630.1189052-5-vkoul@kernel.org
qup0 has 7 SEs, with SE7 as uart and already added, so add the
remaining 6 SEs (i2c and spi) along with pinconf for these SEs
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220414101630.1189052-4-vkoul@kernel.org
qupv3_id_0 was missing iommus property which cause any dma transaction
to fail and board crash. So add the missing iommus.
While at it also add interconnect nodes for qup
Fixes: 5188049c9b ("arm64: dts: qcom: Add base SM8450 DTSI")
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220414101630.1189052-3-vkoul@kernel.org
GPI DMA can be used for DMA operations for QUP devices, so add the three
gpi_dma insances found in this SoC
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220414101630.1189052-2-vkoul@kernel.org
Some versions of the firmware for the SM8350 Hardware Development Kit
(HDK) has FIFO mode disabled for i2c13 and must thus use GPI DMA. Enable
&gpi_dma1 to allow this.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20220412215137.2385831-3-bjorn.andersson@linaro.org
The GENI I2C and SPI controllers may use the GPI DMA engine, define the
rx and tx channels for these controllers to enable this.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20220412215137.2385831-2-bjorn.andersson@linaro.org
Adding wakeup-source property for USB controller in SC7280.
This property is added to inform that the USB controller is
wake up capable and to conditionally power down the phy during
system suspend.
Signed-off-by: Sandeep Maheswaram <quic_c_sanm@quicinc.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1649704614-31518-7-git-send-email-quic_c_sanm@quicinc.com
Using node paths to extend or override a device tree node is error
prone. If there was a typo error, a new node will be created instead of
extending the existing node. This will lead to run-time errors that
could be hard to detect.
A mistyped label on the other hand, will cause a dtc compile error
(during build time). This also reduces the indentation making the code
easier to read.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220402192859.154977-2-krzysztof.kozlowski@linaro.org
Using node paths to extend or override a device tree node is error
prone. If there was a typo error, a new node will be created instead of
extending the existing node. This will lead to run-time errors that
could be hard to detect.
A mistyped label on the other hand, will cause a dtc compile error
(during build time). This also reduces the indentation making the code
easier to read.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220402192859.154977-1-krzysztof.kozlowski@linaro.org
Like the c630, the Poco F1 is also capable of using both antenna
channels for 2.4 and 5ghz wifi, however unlike the c630 only the first
channel is used for bluetooth. Similar to Oneplus 6.
Signed-off-by: Joel Selvaraj <jo@jsfamily.in>
Reviewed-by: Caleb Connolly <caleb@connolly.tech>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/BY5PR02MB7009E2566F9000F338432761D91F9@BY5PR02MB7009.namprd02.prod.outlook.com
