1) stream allocation cannot fail
2) some warnings were removed when functions safely ignored
the calling parameters being wrong.
3) some warnings were removed when functions did not consider
the state as an error since we did not return an error code.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Problem reported that some bgp and ospf json commands did not return
any json output at all if the bgp/ospf instance did not exist.
Additionally, some bgp and ospf json commands did not return any json
output if the instance existed but no neighbors were defined. This
fix makes these commands more consistent in returning empty braces for
json output and issue a message if not using json output. Additionally,
made the flag "use_json" a bool to make it consistent since previously,
it had been defined as an int, char, u_char, and bool at various places.
Ticket: CM-21040
Signed-off-by: Don Slice <dslice@cumulusnetworks.com>
The Vrf aliases can be known with a specific hook. That hook will then,
from zebra propagate the information to the relevant zapi clients.
The registration hook function is the same for all daemons.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
The problem is seen where speed mismatch caused ECMP route
not being reflected with correct number paths (NHs).
During cold boot, some interface speed updated by zebra as
part of one shot timer and triggers interface add to clients.
In this case, ospf already have created interface (bond interface),
but speed was not updated, trigger to do interface speed change
as part of interface add, which will trigger all Router LSA to
use updated speed into cost calculation.
Ticket:CM-22170
Testing Done:
Bring up CLOS config with Spine and leafs. Leaf have CLAG pair,
with same VRR ip address.
At spine one of the bond connecting to leaf node was having
higher speed than the paired device, With this fix, at spine (DUT)
bond interface speed is equal from all peer nodes.
Signed-off-by: Chirag Shah <chirag@cumulusnetworks.com>
The ospf_external_route_lookup function was not
being used so let's just remove it.
Unfortunately the removal was not quite so simple as
that ospf_asbr.h was being used to generate a reference
for the `struct ospf_route` data structure, so we
need to fix up the compile by fixing up header
inclusions so that ospf_route.h is actually included
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
In all but one instance we were following this pattern
with ospf_lsa_new:
ospf_lsa_new()
ospf_lsa_data_new()
so let's create a ospf_lsa_new_and_data to abstract
this bit of fun and cleanup all the places where
it assumes these function calls can fail.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
* Use the correct license header
* Stop headers from including themselves
* Use uniform relative include conventions
* Ensure that sources include what they use
* Turn off clang-format around struct array blocks
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
There is no need to check for failure of a ALLOC call
as that any failure to do so will result in a assert
happening. So we can safely remove all of this code.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Don't show BFD commands with timers since it might confuse users
("show running-config" won't display timers in client daemons anymore),
but keep accepting this command from previous configurations.
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
When BFD timers are configured, don't show it anymore in the daemon
side. This will help us migrate the timers command from daemons to
`bfdd`.
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
When calling route_map_finish, every place that we do we must
first set the deletion event to NULL, or we will create an infinite
loop, if we are using the delayed route-map application code.
As such we might as well just make the route_map_finish code
do this work, as that there is really no viable alternative here
and route_map_finish should only be called on shutdown.
This fixes an infinite loop in zebra on shutdown when there
are route-maps.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Details:
- INET_ADDRSTRLEN is 16, for xxx.xxx.xxx\0, so 15 is now passed
to the strncpy call instead of 16, ensuring ASCII-z output
Signed-off-by: F. Aragon <paco@voltanet.io>
We lookup the lp value and lookup_linkparams_by_instance
can return NULL if something has gone terribly wrong.
Make sure that lp is not NULL.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
When we first get a packet, we need to know if we are self
originated later to make correct decisions. Go ahead and
note that we do not plan to make any decision points
about our self origination here.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Programs that link to libnetsnmp must be compiled using a special set
of flags as specified by the "net-snmp-config --base-cflags" command
(whose output is stored in the SNMP_CFLAGS variable). The problem is
that "net-snmp-config --base-cflags" can output -std=c99 in addition to
other compiler flags in some platforms, and this breaks the build since
FRR souce code makes use of some GNU compiler extensions (e.g. allow
trailing commas in function parameter lists). In order to solve this
problem, append -std=gnu99 after SNMP_CFLAGS in all makefiles where this
variable is used. This way the -std=c99 flag will be overwritten when it's
present. Source files that don't link to libnetsnmp will be compiled using
either -std=gnu99 or -std=gnu11 depending on the compiler availability.
Fixes#1617.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Currently, interface packet transmit queue is created/deleted
as part of Interface UP/Down event. This results in
a rare condition where port came up but queue
was not created. The creation of queue occupies only few bytes.
Moving fifo queue creation to interface create
would add few bytes of fifo creation but at least it guaranteed
to be available during Up/down -->Up event.
Initialize ospf packet fifo queue during ospf
interface creation.
Drain queue during interface down event.
Drained and free the queue as part of the interface
delete/cleanup.
Ticket:CM-20744
Testing Done:
Bring up ospfv2 topology with multiple neighbors.
1) Trigger multiple shut/no shut events and validate
all queues are freed.
2) configure/deconfigure router ospf and validate
all ospf instance and interface underneath are freed.
Signed-off-by: Chirag Shah <chirag@cumulusnetworks.com>
Macro that expands to be wrapped in parentheses was being used as a raw
condition for an if statement, leading to some very weird and confusing
formatting...
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
OSPF_IF_PARAM_CONFIGURED(S, P) checks both the nullity of S and the
value of P; assuming either one from the value of this macro is
incorrect.
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
The following types are nonstandard:
- u_char
- u_short
- u_int
- u_long
- u_int8_t
- u_int16_t
- u_int32_t
Replace them with the C99 standard types:
- uint8_t
- unsigned short
- unsigned int
- unsigned long
- uint8_t
- uint16_t
- uint32_t
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
Otherwise if it is scheduled the thread pointer will be accessed after
the shutdown task finishes accessing, having deleted the structure that
owns said pointer, which causes a heap UAF.
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
This capability, when used, is mapped over linux sys_admin capability.
This is necessary from the daemon perspective, in order to handle NETNS
based VRFs, because calling setns() requires sys admin capability.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
When OSPF SR is not configured one would expect
to not see any output from it at all in the debug
log with no debugs turned on.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
So when a ospf SR is sending down routes to the kernel
ensure that the nexthop vrf_id is set appropriately.
Yes SR is in the default VRF. But for people who
run across this code in the future, they will know
to do the right thing from it.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
- To ease checking the Segment Routing conformity in topotest,
add json output to 'show ip ospf database segment-routing' CLI.
- Update ospfd user guide accordingly
- Update OSPF-SR documentation with supported features and interoperability
Signed-off-by: Olivier Dugeon <olivier.dugeon@orange.com>
The change consists in taking into account of the VRF identifier upon
which the ospf socket is created. Moreover, if the VRF is a netns
backend, then it is not necessary to perform the bind operations to vrf
device.
Also, when a VRF instance is enabled, it informs ospf VRF, and automatically
OSPF VRF benefits from it. Reversely, when VRF instance is disabled,
then OSPF VRF will be disabled too.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
the vrf identifier in the ospf_vrf_enable routine is never read, then
does not need to be initialised.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
- Lan Adjacency TLVs was incorrectly formatted due to an error in
TLV size computation. Add new macro to fix this issue
- Update SR link nexthop when it corresponds to an LAN Adj SID. The nexthop
is set to the router id in the TLVi (as per draft), but we need the neighbor
IP address to set the corresponding MPLS LFIB entry
Signed-off-by: Olivier Dugeon <olivier.dugeon@orange.com>
Fix a || && mixup.
Add an assert for area to show we expect it to be non-null
going forward.
When memory is allocated if it fails we abort then
no need to check for null.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
- ospfd/ospf_opaque.c: Update issue #1652 by introducing a new
function 'free_opaque_info_owner()' to clean list of callback owner
and call this function in appropriate place where 'listdelete_and_null'
is not used.
- ospfd/ospf_packet.c: In case of crash, ospfd is not been able to
flush LSA. In case of self Opaque LSA, when restarting, ospfd crash
during the resynchronisation process with its neighbor due to an
empty list of LSA to flood. Just add a control on the list count
in 'ospf_ls_upd_queue_send()' to escape the function and avoid the
problem.
Signed-off-by: Olivier Dugeon <olivier.dugeon@orange.com>
Turns out we had 3 different ways to define labels
all of them overlapping with the same meanings.
Consolidate to 1. This one choosen is consistent
naming wise with what the *bsd and linux kernels
use.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
show ip ospf [vrf all] interface json and
show ip ospf [vrf all] neighbor json to display
objects in dictionary output rather in array list.
Ticket:CM-19115,CM-19097
Signed-off-by: Chirag Shah <chirag@cumulusnetworks.com>
Opaque LSA were incorrectly filtered. LSA Type 1 with a
router id set to 4.x.x.x or 7.x.x.x. or 8.x.x.x are not correctly
filtered and pass to Segment Routing as wrong Opaque LSA of type
Router Information, Extended Prefix respectively Extended Link.
- Add Opaque LSA check to the filter
The CLI command 'segment-routing prefix' didn't check if a same prefix
already exist in SRDB resulting to multiple entries in the SRDB for the
same prefix.
- Update prefix intead of adding a new one if already present in the SRDB
Signed-off-by: Olivier Dugeon <olivier.dugeon@orange.com>
When preforming CI test, CLI command 'no router ospf' followed by a
'router ospf' is performed to clean up the previous configuration.
Ospfd crash when configuring 'netwoark area'.
This is due to opsf_opaque_term() introduce in previous commit that cause this
crash. It remove not only Opaque LSA but also the list through the call to
'list_delete_and_null()' function. Same take place in 'ospf_mpls_te_term()',
'ospf_router_info_term()' and 'ospf_ext_term()' function.
New set of 'ospf_XXX_finish()' has been introduced to solve this issue while
keeping the possiblity to terminate properly the Opaque LSA and remove MPLS
LFIB entries set by Segment Routing.
Signed-off-by: Olivier Dugeon <olivier.dugeon@orange.com>
- When Extended Prefix LSA need to be refresh, paramaters may be
taken from the wrong interface i.e. Extended Link instead of Prefix
resulting in producing an empty LSA body. Then, ospfd crash due to the
assert on LSA length in ospf_lsa_different() function: code check that
the LSA size is larger than LSA header i.e. LSA is not empty.
Signed-off-by: Olivier Dugeon <olivier.dugeon@orange.com>
- ospfd/ospf_te.c: Remove unregister function and call to
ospf_delete_opaque_functab() following the introduction of
ospf_opaque_term() function in ospfd.c for ospfd termination.
- ospfd/ospf_sr.c: Set initial index value for node-msd CLI to
avaoid crash when using this command
- ospfd/ospf_ext.c: Disable call to ospf_sr_update_prefix() if
Segment Routing, thus Extended Link/Prefix, is not enable
- ospfd/ospf_opaque.c: Correct scheduling of Opaque LSA flooding
Signed-off-by: Olivier Dugeon <olivier.dugeon@orange.com>
- Line 865 in ospfd/ospf_ext.c cause compilation failure when
-werror is set. This line was not necessary and add only for debugging
purpose.
Signed-off-by: Olivier Dugeon <olivier.dugeon@orange.com>
Fix default-information parsing of metric-type,
route-map.
show running to display metic-type 2.
metric, metric-type and route-map can be configured in
any order, running-config displays in specific order..
Signed-off-by: Chirag Shah <chirag@cumulusnetworks.com>
Following various review, following files have been modfied:
- All: Change u_intXX_t typedef to standard uintXX_t types
- doc/OSPF-SR.rst: Update doc in particular the Linux Kernel configuration
section
- doc/ospfd.texi: Update CLI
- ospfd/ospf_dump.[c,h]: Add new 'debug ospf sr' when performing 'sh run'
- ospfd/ospf_ext.[c, h]: Various bug corrections notably to handle flooding of
Extended Prefix at startup. iFix TLVs size for LAN Adjacency.
Update Licence as per Community.md
- ospfd/ospf_opaque.c: Add proper termination function call to remove MPLS entries
- ospfd/ospf_ri.[c,h]: Bug corrections
- ospfd/ospf_sr.[c,h]: Various bug corrections, notably to determine the nexthop
SR Node. Add support to 'no-php-flag'.
Update Licence as per Community.md
- ospfd/ospfd.c: Add call to 'ospf_opaque_term()'
Signed-off-by: Olivier Dugeon <olivier.dugeon@orange.com>
Call Route-map, prefix-list clean up routines and
vrf clearnup during ospf daemon exit routine.
Signed-off-by: Chirag Shah <chirag@cumulusnetworks.com>
Issue 1652 was related to OSPF Crash on termination when ospf is
configured to flood self Opaque LSA e.g TE or RI Opaque LSA.
Analysis:
The problem resides in free_opaque_info_per_type() line 576 of
ospf_opaque.c. Once LSA flush, the function removes by calling
listnode_delete() function the opaque_info_per_type data structure.
However, this is also performed at the upper level function
ospf_opaque_type10lsa_term() which call list_delete_and_null() function.
This result into a double free pointer exception.
Solution:
Remove call to listnode_delete() calls in free_opaque_info_per_type()
function as it is done by list_delete_and_null(). Delete lines 592 - 615.
Remove also second call to ospf_opaque_type10lsa_term() in ospfd.c line 848.
Signed-off-by: Olivier Dugeon <olivier.dugeon@orange.com>
- Change all u_intXX_t typedef to standard type uintXX_t
- Correct removal of ZEBRA_OSPF_SR route in ospf_sr.c line 670
Signed-off-by: Olivier Dugeon <olivier.dugeon@orange.com>
- Remove OSPD_SR route type
- Check that Segment Routing is enable only in default VRF
- Add comment for SRGB in lib/mpls.h
- Update documentation
Signed-off-by: Olivier Dugeon <olivier.dugeon@orange.com>
Current json output does not differentiate start of
neighbor ip object. Adding "neighbors" keyword at the
beginning of neighbor list. This is useful when
displaying vrf level output along with neighbors
list.
Ticket:CM-19097
Testing Done:
show ip ospf neighbor json
show ip ospf vrf all neighbor json
Signed-off-by: Chirag Shah <chirag@cumulusnetworks.com>
- ospf_ext.c: Correct deferred pointer raised by valgrind
- ospf_sr.c: Correct deffered pointer raised by valgrind. Modify
Segment Routing shutdown. This is due to the fact that RI LSA
4.0.0.0 is flush prior to 7.0.0.X & 8.0.0.X LSA. This trigger
SR-Node deletion which also remove all Extended Link / Prefix
leaving them unavailable when there are referenced by 7.0.0.X
& 8.0.0.X LSA flushing.
- doc/OSPF-SR.rst: Correct Restructured Text syntax and add
Configuration example as well as Credit section
Signed-off-by: Olivier Dugeon <olivier.dugeon@orange.com>
This is an implementation of draft-ietf-ospf-segment-routing-extensions-24
and RFC7684 for Extended Link & Prefix Opaque LSA.
Look to doc/OSPF_SR.rst for implementation details & known limitations.
New files:
- ospfd/ospf_sr.h: Segment Routing structure definition (SubTLVs + SRDB)
- ospfd/ospf_sr.c: Main functions for Segment Routing support
- ospfd/ospf_ext.h: TLVs and SubTLVs definition for RFC7684
- ospfd/ospf_ext.c: RFC7684 Extended Link / Prefix implementation
- doc/OSPF-SRr.rst: Documentation
Modified Files:
- doc/ospfd.texi: Add new Segment Routing CLI command definition
- lib/command.h: Add new string command for Segment Routing CLI
- lib/mpls.h: Add default value for SRGB
- lib/route_types.txt: Add new OSPF Segment Routing route type
- ospfd/ospf_dump.[c,h]: Add OSPF SR debug
- ospfd/ospf_memory.[c,h]: Add new Segment Routing memory type
- ospfd/ospf_opaque.[c,h]: Add ospf_sr_init() starting function
- ospfd/ospf_ri.c: Add new functions to Set/Get Segment Routing TLVs
Add new ospf_router_info_lsa_upadte() to send Opaque LSA to ospf_sr.c()
- ospfd/ospf_ri.h: Add new Router Information SR SubTLVs
- ospfd/ospf_spf.c: Add new scheduler when running SPF to trigger
update of NHLFE
- ospfd/ospfd.h: Add new thread for Segment Routing scheduler
- ospfd/subdir.am: Add new files
- vtysh/Makefile.am: Add new ospf_sr.c file for vtysh
- zebra/kernel_netlink.c: Add new OSPF_SR route type
- zebra/rt_netlink.[c,h]: Add new OSPF_SR route type
- zebra/zebra_mpls.h: Add new OSPF_SR route type
Signed-off-by: Olivier Dugeon <olivier.dugeon@orange.com>
Inform the .clang-format file about LSDB_LOOP and
put the proper indentation for this loop into the
code.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Current json output does not differentiate start of
interface objects. Adding "interfaces" keyword at the
beginning of the interface list. This is useful
when displaying vrf level output along with interface list.
Ticket:CM-19115
Testing Done:
show ip ospf vrf all interface json
show ip ospf vrf all interface <specific intf> json
show ip ospf interface json
show ip ospf interface <specific intf> json
Signed-off-by: Chirag Shah <chirag@cumulusnetworks.com>
Signed-off-by: Daniel Walton <dwalton@cumulusnetworks.com>
Before
------
cel-redxp-10(config)# router ospf vrf RED
cel-redxp-10(config-router)# network 1.1.1.1/32 area 0.0.0.0
cel-redxp-10(config-router)# network 1.1.1.1/32 area 0.0.0.0
There is already same network statement.
cel-redxp-10(config-router)#
When we see the "There is already same network statement." message
vtysh exits non-zero. This scenario breaks frr-reload because
the command took and it in the config, it should exit zero here.
After
-----
cel-redxp-10(config)# router ospf vrf RED
cel-redxp-10(config-router)# network 1.1.1.1/32 area 0.0.0.0
cel-redxp-10(config-router)# network 1.1.1.1/32 area 0.0.0.0
cel-redxp-10(config-router)# network 1.1.1.1/32 area 0.0.0.0
cel-redxp-10(config-router)# network 1.1.1.1/32 area 0
cel-redxp-10(config-router)#
cel-redxp-10(config-router)# network 1.1.1.1/32 area 0.0.0.1
There is already same network statement.
cel-redxp-10(config-router)#
Current OSPF VRF configuration are allow pre-provisining even if
VRF is not configured. In such case ospf->vrf_id would VRF_UNKNOWN,
when passive interface configuration done under such ospf instance,
it would lookup all vrf_device and try to create ifp with unknown
vrf_id.
for passive interface config command lookup ifp for vrf_id is within range.
Ticket:CM-19156
Testing Done:
Configure
Cumulus#: router ospf vrf vrf1
Cumulus(config-router)#: passive interface swp16
interface swp16 not found.
Signed-off-by: Chirag Shah <chirag@cumulusnetworks.com>
The $Id: lines would allow code kept in cvs to substitute
the file version upon checkout. Since we are not using
cvs there is no need to keep these lines anymore.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
no router ospf removes default ospf instance,
if there are other non-default vrf instance present
with interface level configuration. Lookup ospf instance
for ifp->vrf_id, if ospf instnace present use that
to access 'instance id'.
Ticket: CM-19078
Testing Done:
run no router ospf and show running config along with other
non-default vrf aware ospf configurations.
Signed-off-by: Chirag Shah <chirag@cumulusnetworks.com>
OSPF interface specific configuration can be done independent
of router ospf [vrf x] global config.
In cases where ospf interface non default vrf configuration
is done prior to 'router ospf vrf x', show running-config
would not display such configuration.
To display configuration now walk all vrfs and interface list
and only display where OSPF configure params are set.
Ticket:CM-18952
Testing Done:
Tried ospf interface specific configuration with VRF,
where router ospf vrf x is not present.
Signed-off-by: Chirag Shah <chirag@cumulusnetworks.com>
Some of the deprecated stream.h macros see such little use that we may
as well just remove them and use the non-deprecated macros.
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
Allow the higher level protocol to specify if it would
like to receive notifications about it's routes that
it has installed.
I've purposely made it part of zclient_new_notify because
we need to track the routes on a per daemon basis only.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Display area x.x.x.x nssa configuration in
running-config. Using nssa translate candiate (default)
case to display 'area x nssa'.
Ticket:CM-18947
Reviewed By:
Testing Done:
Tried various combinations of nssa config,
verified show running-config ospfd output
router ospf
area 2.2.2.2 nssa
area 2.2.2.2 nssa no-summary
router ospf
area 2.2.2.2 nssa translate-always
area 2.2.2.2 nssa no-summary
Signed-off-by: Chirag Shah <chirag@cumulusnetworks.com>
Define JSON_C_TO_STRING_NOSLASHESCAPE used for
escaping forward slash.
Disply json output for
'show ip ospf route [vrf all] json'
Ticket:CM-18659
Reviewed By:
Testing Done:
Configure multiple non-default VRF, inject external routes
via redistribute to ospf area.
checked show ip ospf route vrf all /json based output.
Signed-off-by: Chirag Shah <chirag@cumulusnetworks.com>
show running-config to display VRF aware ospf instances
even if VRF is not active. This will allow the user to
configured ospf instances configurations even if VRF is not
active. 'show ip ospf vrf all' does not display until VRF
is active.
Ticket:CM-18949
Reviewed By:
Testing Done:
Configure non-default vrf aware ospfs with prior vrf devices
configured.
All vrf aware 'router ospf' displayed in running-configuration.
Disable one of the vrf device still all vrf aware 'router ospf'
displayed in running-config, but 'show ip ospf vrf all' does
not display for which VRF is not active.
Signed-off-by: Chirag Shah <chirag@cumulusnetworks.com>
Upon restart frr interface configuration applied
prior to 'router ospf' configuration. 'ip ospf area x'
config fails if ospf instance is not active.
Allow 'ip ospf area x' configuration to allow in absence
of ospf instance. Upon 'router ospf' walk through vrf
aware interfaces, active area cofigurations.
When vrf is enabled, router-id update also walk through
vrf aware interfaces to enable area configuration
via network_run_interface.
Ticket: CM-18927
Reviewed By:
Testing Done:
Configured multiple interfaces with 'ip ospf area x'
with multiple areas/interface combinations.
Upon router ospf enable along with vrf is active,
interfaces comes up in respective area, ospf neighborship
comes up fine.
Signed-off-by: Chirag Shah <chirag@cumulusnetworks.com>
Currently, ospf external routers are part of struct
ospf_master which is not vrf aware ospf instance.
All ospf external routes are injected/leaked into all
vrfs.
Moved ospf external routes db to struct ospf to make
vrf aware, such one external routes learnt in one vrf
is not leaked into another vrf.
Ticket:CM-18855
Testing Done:
Inject external route in non-default vrf x, validated
ospf database across the vrf x, validated ospf routes
for vrf x.
Signed-off-by: Chirag Shah <chirag@cumulusnetworks.com>
Router-ID change or ospf instance going down,
send LS-Upd with MAXAGE to self origintated LSAs to
all ospf neighbors.
Ticket:CM-1576
Testing Done:
Bring R1 - R2, Change Router-ID on R2, restart frr on R2
Validated R1 ospf LSDB for max aged 3600 LSA from R2.
Signed-off-by: Chirag Shah <chirag@cumulusnetworks.com>
Ensure zebra received router-id isolated per vrf instance.
Store zebra received router-id within ospf instance.
Ticket:CM-18657
Reviewed By:
Testing Done:
Validated follwoing sequence
- Create vrf1111
- Create ospf vrf1111 with no router-id
- Assign ip to vrf111
- ospf is assigned zebra assigned router-id which is vrf ip.
- upon remvoing vrf ip, the router-id retained as same until
ospfd restarted.
Signed-off-by: Chirag Shah <chirag@cumulusnetworks.com>
no router ospf followed by router ospf throws
a message, there isn't active ospf instance.
Fix ospf instance lookup.
Ticket:CM-18675
Testing Done:
Validated router ospf, no router ospf with
VRF and with multi-instance version 'router ospf 2'
configuration clis.
Signed-off-by: Chirag Shah <chirag@cumulusnetworks.com>
Same neighbor learned from multiple ospf interfaces
(all) were not displayed in json, only last was displayed.
Created list within dictionary using neighbor-id as key.
lookup neigbhor-id in json obejct prior to creating new list.
spine-2# show ip ospf neighbor
Neighbor ID Pri State Dead Time Address Interface
0.0.1.16 1 Full/DR 36.754s 8.0.3.15 swp1:8.0.3.16
0.0.1.16 1 Full/DR 30.903s 7.0.3.15 swp2:7.0.3.16
spine-2# show ip ospf neighbor json
{
"0.0.1.16":[
{
"priority":1,
"state":"Full\/DR",
"deadTimeMsecs":35114,
"address":"8.0.3.15",
"ifaceName":"swp1:8.0.3.16",
"retransmitCounter":0,
"requestCounter":0,
"dbSummaryCounter":0
},
{
"priority":1,
"state":"Full\/DR",
"deadTimeMsecs":39264,
"address":"7.0.3.15",
"ifaceName":"swp2:7.0.3.16",
"retransmitCounter":0,
"requestCounter":0,
"dbSummaryCounter":0
}
]
}
Signed-off-by: Chirag Shah <chirag@cumulusnetworks.com>
Seperate the display option in both vty and json
case 'vrf' is used in show command.
show ip ospf 'vrf all' [json]
Display vrf name as key object in json and vrf name
in vty output.
case 'vrf' is not used then only display default
vrf ospf instance and vrf name is not shown in vty and
json.
Signed-off-by: Chirag Shah <chirag@cumulusnetworks.com>
-Fix ordering of nssa command with translate options
and no-summary option.
Just like ospf stub no-summary keep the order order
of nssa no-summary.
- Fix NSSA options.
- Avoid displaying translate-candiate (default) option
in running-config.
cumulus(config-router)# area 2.2.2.2 nssa
<cr>
no-summary Do not inject inter-area routes into nssa
translate-always Configure NSSA-ABR to always translate
translate-candidate Configure NSSA-ABR for translate election (default)
translate-never Configure NSSA-ABR to never translate
Running-config output:
router ospf
area 2.2.2.2 nssa translate-always
area 2.2.2.2 nssa no-summary
Ticket:CM-8312
Signed-off-by: Chirag Shah <chirag@cumulusnetworks.com>
Create an api to display vrf name in vty or json format.
Use VRF Name for vtysh and vrfName for json output.
Signed-off-by: Chirag Shah <chirag@cumulusnetworks.com>
We have memory that is initialized upon ospf instance
and area startup. Free it up on shutdown.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
This improves code readability and also future-proofs our codebase
against new changes in the data structure used to store interfaces.
The FOR_ALL_INTERFACES_ADDRESSES macro was also moved to lib/ but
for now only babeld is using it.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Performance tests showed that, when running on a system with a large
number of interfaces, some daemons would spend a considerable amount
of time in the if_lookup_by_index() function. Introduce a new rb-tree
to solve this problem.
With this change, we need to use the if_set_index() function whenever
we want to change the ifindex of an interface. This is necessary to
ensure that the 'ifaces_by_index' rb-tree is updated accordingly. The
return value of all insert/remove operations in the interface rb-trees
is checked to ensure that an error is logged if a corruption is
detected.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
IFINDEX_DELETED is not necessary anymore as we moved from a global
list of interfaces to a list of interfaces per VRF.
This reverts commit 84361d615.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
This is an important optimization for users running FRR on systems with
a large number of interfaces (e.g. thousands of tunnels). Red-black
trees scale much better than sorted linked-lists and also store the
elements in an ordered way (contrary to hash tables).
This is a big patch but the interesting bits are all in lib/if.[ch].
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Make use of strnlen() and strlcpy() so we can get rid of these
convoluted if_*_by_name_len() functions.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
list_free is occassionally being used to delete the
list and accidently not deleting all the nodes.
We keep running across this usage pattern. Let's
remove the temptation and only allow list_delete
to handle list deletion.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Convert the list_delete(struct list *) function to use
struct list **. This is to allow the list pointer to be nulled.
I keep running into uses of this list_delete function where we
forget to set the returned pointer to NULL and attempt to use
it and then experience a crash, usually after the developer
has long since left the building.
Let's make the api explicit in it setting the list pointer
to null.
Cynical Prediction: This code will expose a attempt
to use the NULL'ed list pointer in some obscure bit
of code.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
maxage_lsa using prefix structure to store in route_table.
The lsa pointer is 4-8 bytes depending on arch, but prefix member field
would be 1 byte. Use ptr field of prefix structure to store lsa pointer.
Also memset to initialize to avoid crash on ARM platform as same LSA is
referenced from multiple times during shutdown of ospf.
Signed-off-by: Chirag Shah <chirag@cumulusnetworks.com>
Current cleanup is for unset values or variables that are not used anymore.
Regarding ospfd/ospf_vty.c: argv_find()
we'll never get it NULL, so get coststr = argv[idx]->arg;
This is a fallout from PR #1022 (zapi consolidation). In the early days,
the client daemons would allocate enough memory to send all nexthops
to zebra. Then zebra would add all nexthops to the RIB and respect
MULTIPATH_NUM only when installing the routes in the kernel. Now things
are different and the client daemons can send at most MULTIPATH_NUM
nexthops to zebra, and failure to respect that will result in a buffer
overflow. The MULTIPATH_NUM limit in the new zebra API is a small price
we pay to avoid allocating memory for each route sent to zebra.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Signed-off-by: Daniel Walton <dwalton@cumulusnetworks.com>
If the user configures some command that is already in the config we
should return CMD_WARNING instead of CMD_WARNING_CONFIG_FAILED
There are a variety of cli's associated with the
'set metric ...' command. The problem that we
are experiencing is that not all the daemons
support all the varieties of the set metric
and the returned of NULL during the XXX_compile
phase for these unsupported commands is causing
issues. Modify the code base to only return
NULL if we encounter a true parsing issue.
Else we need to keep track if this metric
applies to us or not.
In the case of rip or ripngd if the metric
passed to us is greater than 16 just turn
it internally into a MAX_METRIC.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Using the previously-added vty_frame() support, this gets rid of all the
pointless empty "interface XYZ" blocks that get added for any interface
that shows up in the system (e.g. dummys, tunnels, etc.)
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
FLAG_BLACKHOLE is used for different things in different places. remove
it from the zclient API, instead indicate blackholes as proper nexthops
inside the message.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Some differences compared to the old API:
* Now the redistributed routes are sent using address-family
independent messages (ZEBRA_REDISTRIBUTE_ROUTE_ADD and
ZEBRA_REDISTRIBUTE_ROUTE_DEL). This allows us to unify the ipv4/ipv6
zclient callbacks in the client daemons and thus remove a lot of
duplicate code;
* Now zebra sends all nexthops of the redistributed routes to the client
daemons, not only the first one. This shouldn't have any noticeable
performance implications and will allow us to remove an ugly exception
we had for ldpd (which needs to know all nexthops of the redistributed
routes). The other client daemons can simply ignore the nexthops if
they want or consult just the first one (e.g. ospfd/ospf6d/ripd/ripngd).
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Change all callers of IPV4_ADDR_SAME() to pass a pointer to a struct in_addr
Use assignment and comparison instead of memcpy() and memcmp(). Avoids function
calls. Faster.
Signed-off-by: Jorge Boncompte <jbonor@gmail.com>
Fix ANVL-OSPF-5.1 reported ospfd crash.
vertex_nexthop_free was added as valgrind reported potential
memory leak, but in some cases nexthop would not be available
freed.
The actual nexthop free is part of ospf_canonical_nexthops_free(),
upon trying to free, qfree checks mtype count becomes 0 and asserts.
Removing vertex_nexthop_free() from ospf_spf_flush_parents().
Signed-off-by: Chirag Shah <chirag@cumulusnetworks.com>
This allows modules to register their own additional hooks on interface
creation/deletion.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Remove assert in path of router_id_update:
Upon configuring same router-id as neighbor's
assert would cause a crash. Log a warning message
and neighborship would not come up.
Address memory leaks
Signed-off-by: Chirag Shah <chirag@cumulusnetworks.com>
Handle all instance base clis calling ospf_lookup_instance()
to return CMD_NOT_MY_INSTANCE in case of ospf is not found.
Signed-off-by: Chirag Shah <chirag@cumulusnetworks.com>
Multi-Instance OSPF configuration CLI would fail because
first client return error upon seeing qobj_index being 0.
With new marco generate new error code to return from each
instance (vtysh client) and if the command is intended for given
instance, its qobj_index would be nonzero and process the command
and push correct ospf context. Other instance would return the error.
On vtysh end, check all instance return an error log a message to a
file.
Testing Done:
Verfied various MI-OSPF configuration CLI with multi instances.
Signed-off-by: Chirag Shah <chirag@cumulusnetworks.com>
called list_delete instead of list_free
Moved MTYPE_STATIC in ospfd/zebra.c
Revert changes in ospf6_zebra.c where malloc is called for
multiple nexthops.
Signed-off-by: Chirag Shah <chirag@cumulusnetworks.com>
* Functions that build TLVs in ospf_te.c and ospf_te.c use 'tlvh + 1'
to move the pointer to the TLV payload ifor strem_put().
* Correct this by using TLV_DATA() macro which is saffer.
Signed-off-by: Olivier Dugeon <olivier.dugeon@orange.com>
* Remove enum status_t opcode in ospfd.h
* Replace enum status_t opcode by bool enabled in ospf_te.[c,h] and ospf_ri.c
* Add missign parenthesis '()' around 'if CHECK_FLAG' in ospf_te.c and ospf_ri.c
Signed-off-by: Olivier Dugeon <olivier.dugeon@orange.com>
This reverts commit c14777c6bf.
clang 5 is not widely available enough for people to indent with. This
is particularly problematic when rebasing/adjusting branches.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
* TLV macros where define itwice in ospf_te.h and in ospf_ri.h
* Merge both definition in ospf_opaque.h and adjust accordingly RI and TE
* Same for typedef status_t which is move in ospfd.h
* Remove also all 'goto' statement in ospf_te.c and ospf_ri.c
* Remove strange function lookup_oi_by_ifp() in ospf_te.c and replace it
by a valid code in initialize_linkparams() function
Signed-off-by: Olivier Dugeon <olivier.dugeon@orange.com>
Signed-off-by: Daniel Walton <dwalton@cumulusnetworks.com>
This allows frr-reload.py (or anything else that scripts via vtysh)
to know if the vtysh command worked or hit an error.
Two things:
1) Some advanced 'show ip ospf database'... code
was not working properly. Fix the cli to handle
this appropriately
2) Consolidate two cli functions into one.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworkscom>
Several changes were made from the original patch to resolve conflicts
and also to fix various issues that were discovered during testing. Below
is the original commit message minus a few parts that correspond to code
that was dropped during bug fixing.
Signed-off-by: Jafar Al-Gharaibeh <jafar@atcorp.com>
ospfd: Extend 'ip ospf area' to take address argument + rationalise ospf enable
* ospfd.c: (general) Clean up the whole running of OSPF on interfaces.
(add_ospf_interface) taking (struct interface *) arg is pointless here.
(ospf_is_ready) new helper.
(ospf_network_run_subnet) Put all the code for choosing whether to enable
OSPF on a subnet, and if so which area configuration to use, here. If a
subnet should not be enabled, ensure an existing oi is freed.
(ospf_network_run_interface) Just call run_subnet for all subnets on an
interface.
(ospf_network_run) Just call run_interface for all interfaces.
(ospf_if_update) Just call run_interface for the given interface.
(ospf_network_unset) Just call run_subnet for existing ois.
(ospf_update_interface_area) helper: update area on an oi, or create it.
(ospf_interface_set) renamed to ospf_interface_area_set for clarity.
Ensures OSPF is created, then into if_update.
(ospf_interface_unset) renamed to ospf_interface_area_unset and collapses
down to simple loop to call run_subnet for all ois.
* ospf_interface.h: add a more general OSPF_IF_PARAM_IS_SET, which does the
right thing and takes default config into account.
* doc/ospfd.texi: add 'ip ospf area' command.
Acked-by: Donald Sharp <sharpd@cumulusnetworks.com>
This patch has been part of Quagga since October 2015
Orignial Author: Paul Jakma <paul@quagga.net>
Date: Thu Aug 27 16:51:42 2009 +0100
Issue reported that a configuration commonly used on other routing implementations
fails in frr. If under ospf, "network 172.16.1.1/32 area 0" or under eigrp, "network
172.16.1.1/32" is entered, the appropriate interfaces are not included in the routing
protocol. This was because the code was calling prefix_match, which did not match if
the network statement had a longer mask than the interface being matched. This fix
takes away that restriction by creating a "lib/prefix_match_network_statement" function
which doesn't care about the mask of the interface. Manual testing shows both ospf and
eigrp now can be defined with more specific network statements.
Signed-off-by: Don Slice <dslice@cumulusnetworks.com>
log.c provides functionality for associating a constant (typically a
protocol constant) with a string and finding the string given the
constant. However this is highly delicate code that is extremely prone
to stack overflows and off-by-one's due to requiring the developer to
always remember to update the array size constant and to do so correctly
which, as shown by example, is never a good idea.b
The original goal of this code was to try to implement lookups in O(1)
time without a linear search through the message array. Since this code
is used 99% of the time for debugs, it's worth the 5-6 additional cmp's
worst case if it means we avoid explitable bugs due to oversights...
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
ospf redefines the standard route map commands which causes ambiguity
issues in the CLI parser, it also uses a signed integer to hold an
unsigned quantity leading to weirdness when specifying metrics larger
than 2,147,483,647
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
if bandwidth is not set from Zebra use speed as bandwidth
for ospf route.
Testing Done:
Verfied over bond which has aggregated speed of all member interfaces,
cost is reflected in ospf route and ip route.
Manually changed interface bandwidth which replaces speed as bw, instead
uses cli entered value as bw, verifid output of ospf route and ip route.
Signed-off-by: Chirag Shah <chirag@cumulusnetworks.com>
clear ip ospf interface <IFNAME> parsing issue,
instead of arguement of interface "IFNAME" parsed.
Signed-off-by: Chirag Shah <chirag@cumulusnetworks.com>
ospf timers related commands under router ospf were not accepted
due to incorrect argument count check.
timers throttle lsa all (0-5000)
timers throttle spf (0-600000) (0-600000) (0-600000)
timers lsa arrival (0-1000)
timers lsa min-arrival (0-600000)
Signed-off-by: Chirag Shah <chirag@cumulusnetworks.com>
If you are not using OSPF-TE than there is no need to
be warned that we cannot find anything about it.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
If the user enters a decimal, display a decimal.
If the user enters a dotted quad, display a dotted quad.
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
Revert "ospf6d: fix decimal area ID cli"
commit a27cb3cfe9
Revert "bgpd: add back unicast option to 'address-family vpnv(4&6)' Issue #459"
commit 399598bf6b
Revert "Fix the memory leak"
commit d8d58e9839
Revert "zebra: 'no ip route 4.1.1.19 255.255.255.255 99' is ambiguous"
commit 83f3561935
Revert "ospf6d: Allow unconfig of unknown lsa's"
commit 5b0747d71d
Revert "Fix the "Dead assignment" of clang SA."
commit 3a6570a1f1
Revert "snapcraft: Improve README.usage.md based on feedback received"
commit 2a3a819a9c
Revert "zebra: stop deregistering static nexthops unless removing the static"
commit 1dac3a9619
All of these changes do not apply on stable/3.0 due to either CLI
changes or another fix already being present.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
When you have more than one ospf interface configured
to be used, we were attempting to reuse the
json_interface_sub pointer after we added it
to the json data structure.
Ticket: CM-13597
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
We only needed to add/change the vrf callbacks when we initialize
the vrf subsystem. As such it is not necessary to handle the callbacks
in any other way than through the init function.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
The FSF's address changed, and we had a mixture of comment styles for
the GPL file header. (The style with * at the beginning won out with
580 to 141 in existing files.)
Note: I've intentionally left intact other "variations" of the copyright
header, e.g. whether it says "Zebra", "Quagga", "FRR", or nothing.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Pass pointer to pointer instead of assigning by return value. See
previous commit message.
To ensure that the behavior stays functionally correct, any assignments
with the result of a thread_add* function have been transformed to set
the pointer to null before passing it. These can be removed wherever the
pointer is known to already be null.
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
The way thread.c is written, a caller who wishes to be able to cancel a
thread or avoid scheduling it twice must keep a reference to the thread.
Typically this is done with a long lived pointer whose value is checked
for null in order to know if the thread is currently scheduled. The
check-and-schedule idiom is so common that several wrapper macros in
thread.h existed solely to provide it.
This patch removes those macros and adds a new parameter to all
thread_add_* functions which is a pointer to the struct thread * to
store the result of a scheduling call. If the value passed is non-null,
the thread will only be scheduled if the value is null. This helps with
consistency.
A Coccinelle spatch has been used to transform code of the form:
if (t == NULL)
t = thread_add_* (...)
to the form
thread_add_* (..., &t)
The THREAD_ON macros have also been transformed to the underlying
thread.c calls.
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
Fixed output:
robot.cumulusnetworks.com# show ip ospf int
enp0s3 is up
ifindex 2, MTU 1500 bytes, BW 0 Mbit <UP,BROADCAST,RUNNING,MULTICAST>
Internet Address 10.0.2.15/24, Broadcast 10.0.2.255, Area 0.0.0.0
MTU mismatch detection:enabled
Router ID 192.168.0.1, Network Type BROADCAST, Cost: 10
Transmit Delay is 1 sec, State Waiting, Priority 1
No backup designated router on this network
Multicast group memberships: OSPFAllRouters
Timer intervals configured, Hello 10s, Dead 40s, Wait 40s, Retransmit 5
Hello due in 9.611s
Neighbor Count is 0, Adjacent neighbor count is 0
enp0s10 is up
ifindex 7, MTU 1500 bytes, BW 0 Mbit <UP,BROADCAST,RUNNING,MULTICAST>
Internet Address 192.168.201.146/24, Broadcast 192.168.201.255, Area 0.0.0.0
MTU mismatch detection:enabled
Router ID 192.168.0.1, Network Type BROADCAST, Cost: 10
Transmit Delay is 1 sec, State Waiting, Priority 1
No backup designated router on this network
Multicast group memberships: OSPFAllRouters
Timer intervals configured, Hello 10s, Dead 40s, Wait 40s, Retransmit 5
Hello due in 7.241s
Neighbor Count is 0, Adjacent neighbor count is 0
robot.cumulusnetworks.com# show ip ospf int enp0s3
enp0s3 is up
ifindex 2, MTU 1500 bytes, BW 0 Mbit <UP,BROADCAST,RUNNING,MULTICAST>
Internet Address 10.0.2.15/24, Broadcast 10.0.2.255, Area 0.0.0.0
MTU mismatch detection:enabled
Router ID 192.168.0.1, Network Type BROADCAST, Cost: 10
Transmit Delay is 1 sec, State Waiting, Priority 1
No backup designated router on this network
Multicast group memberships: OSPFAllRouters
Timer intervals configured, Hello 10s, Dead 40s, Wait 40s, Retransmit 5
Hello due in 2.915s
Neighbor Count is 0, Adjacent neighbor count is 0
robot.cumulusnetworks.com# show ip ospf int enp0s10 json
{
"enp0s10":{
"ifUp":true,
"ifIndex":7,
"mtuBytes":1500,
"bandwidthMbit":0,
"ifFlags":"<UP,BROADCAST,RUNNING,MULTICAST>",
"ospfEnabled":true,
"ipAddress":"192.168.201.146",
"ipAddressPrefixlen":24,
"ospfIfType":"Broadcast",
"localIfUsed":"192.168.201.255",
"area":"0.0.0.0",
"routerId":"192.168.0.1",
"networkType":"BROADCAST",
"cost":10,
"transmitDelayMsecs":1000,
"state":"Waiting",
"priority":1,
"mcastMemberOspfAllRouters":true,
"timerMsecs":100,
"timerDeadMsecs":25,
"timerWaitMsecs":25,
"timerRetransmit":200,
"timerHelloInMsecs":2106,
"nbrCount":0,
"nbrAdjacentCount":0
}
}
robot.cumulusnetworks.com#
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
The SNMP modules include <net-snmp/net-snmp-config.h>, which won't be
found in off-searchpath directories without SNMP_CFLAGS. Unfortunately
in my tests the files were on the search path even without the flags.
(SNMP_LIBS is not needed because only libfrrsnmp calls into net-snmp
functions.)
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
OSPF distance commands were broken in a variety of ways. Fix 'em.
* `distance ospf` and `distance ospf6` were accepted commands
* Inconsistent doc strings
* Make use of {keyword|tokens}
* Add ability to reset specific distance without specifying a value
Ex: ~# no distance ospf6 intra
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
These have copies in vtysh that do the node-switch locally and are
listed in extract.pl's ignore list. The ignore list however is
redundant since DEFUN_NOSH does the same thing...
ldpd is a bit hacky, but Renato is reworking this anyway.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
This means there are no ties into the SNMP code anymore other than the
init call at startup.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
There were some typos in command line help, also the "e:" spec was
missing for getopt in zebra/bgpd (even before the refactor).
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Contains the fetch-and-run-thread logic, and vty startup (which is the
last thing happening before entering the main loop).
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Centralise read_config/daemonize/dryrun/pidfile/vty_serv into libfrr.
This also makes multi-instance pid/config handling available as part of
the library. It's only wired up in ospfd, but the code is in lib/.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Start centralising startup & option parsing into the library.
FRR_DAEMON_INFO is a bit weird, but it will become useful later (e.g.
for killing the ZLOG_* enum, and having the daemon name available)
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Coverity: string_overflow: You might overrun the 100-character destination string vty_path by writing 4096 characters from vty_sock_path.
Signed-off-by: Martin Winter <mwinter@opensourcerouting.org>
Coverity: buffer_size_warning: Calling strncpy with a maximum size argument of 100 bytes on destination array pid_file of size 100 bytes might leave the destination string unterminated.
Signed-off-by: Martin Winter <mwinter@opensourcerouting.org>
There's no point in installing libospf anymore, now that
libfrrospfclient doesn't link it.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
The OSPF API-client library doesn't really use anything from libospf
except some small dumping tools. Isolate these into a separate file
and detangle the ospfapiclient library.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Convert the libospfapiclient -> libfrrospfapiclient
and libospf -> libfrrospf to prevent namespace
collision with Quagga.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
The library libzebra that is installed with FRR will
conflict with Quagga. So let's rename it to libfrr.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Somewhere in the past we switched from
using the auto-generated redistribute statements
to a non-generated version. This caused us to
loose new protocols to redistribute as they are
added. Put it back.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
monotime_since() does exactly the same thing.
... and timeval_elapsed is now private to lib/thread.c
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
This ditches tv_add, tv_sub, tv_cmp, etc. in favour of
monotime{,_since,_until}() which actually makes the code much more
readable in some locations.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Conflicts (CLI vs. atol()):
- bgpd/bgp_vty.c
- ospfd/ospf_vty.c
- zebra/zebra_vty.c
NB: pull req #65 (LabNConsulting/working/2.0/afi-safi-vty/c) was
excluded from this merge.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
When unconfiguring certain commands in ospf, you can
run into situations where we attempt to read beyond
the end of a argv[] vector created. On certain platforms
this will crash it.
Ticket: CM-14090
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
* lib/if.h: Remove LP_TE as Link Parameters is set if different from 0
See IS_LINK_PARAMS_SET macro and use LP_TE_METRIC to determine if TE metric
is set or not
* lib/if.c: replace LP_TE by LP_TE_METRIC in default LP status
* zebra/interface.c: replace LP_TE by LP_TE_METRIC and check if TE metric
is equal to standard metric or not
* ospfd/ospf_te.c: replace LP_TE by LP_TE_METRIC
* isisd/isis_te.c: replace LP_TE by LP_TE_METRIC
Signed-off-by: Olivier Dugeon <olivier.dugeon@orange.com>
All of the autogenerated macros in lib/route_types.pl are now called
FRR_* instead of QUAGGA_*.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Several places have paths and names that can change hardcoded, e.g. the
package name and the /var/run path. This fixes a few of them, there's
still some to do.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
This replaces Quagga -> FRR in most configure.ac settings as well as
a handful of preprocessor macros in the source code.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
VTY_DECLVAR_CONTEXT already contains a NULL check, vty warning message
and return statement. These are not needed.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Fix instances that the coccinelle patch didn't catch (or which
coccinelle couldn't parse), and add the patch file for future posterity
(and application to yet-unmerged branches).
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
If we fail to set any socket's buffer size, try again with a smaller value
and keep going until it succeeds. This is better than just giving up or,
even worse, abort the creation of a socket (ospf6d and ripd).
Fix broken ospf6d on FreeBSD.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
This reverts commit b7fe4141, which introduced a logic where the OSPF
send buffer size was dynamically updated to reflect the maximum MTU
of the OSPF enabled interfaces (this was done to make ospfd work with
interfaces configured for jumbo frames).
Since commit a78d75b0, this is not necessary anymore because
ospf_sock_init() now sets the OSPF send buffer size to a very high value
(8MB). Also, the previous logic was broken because it didn't account
for run-time interface MTU changes.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
These now generate warnings which will break the build with -Werror.
Note this may have enabled commands that should be disabled, or the
other way around...
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
When nbr->t_inactivity is not active, and
you do a show json over the neighbor it
will crash ospfd. Fix the code so it
prints out -1 when the timer is inactive.
Ticket:CM-13835
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Don Slice <dslice@cumulusnetworks.com>
Reviewed-by: Daniel Walton <dwalton@cumulusnetworks.com>
(cherry picked from commit 78d8fcb9623ab4d9cebf6187a451448e056a84bf)
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
This moves all install_element calls into the file where the DEFUNs are
located. This fixes several small related bugs:
- ospf6d wasn't installing a "no interface FOO" command
- zebra had a useless copy of "interface FOO"
- pimd's copy of "interface FOO" was not setting qobj_index, which means
"description LINE" commands would fail with an error
The next commit will do the actual act of making "foo_cmd" static.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
When doing a show command under ospf, if
not using json we would have a small memory
leak in show_ip_ospf_common.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
(cherry picked from commit 50750712b1ac8364e290c67782eaf371025dc59e)
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Additionally:
* Add [ip] to a couple bgp show commands
* Quick refactor of a couple ISIS commands
* Quick refactor of a couple OSPF6 commands
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
Signed-off-by: Daniel Walton <dwalton@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ticket: CM-13712
(cherry picked from commit 367b138748e894bbfaae36d1cf7c90eafebfebc9)
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Nice clang catch: ospfd/ospf_vty.c:6710:1: error: all paths through
this function will call itself [-Werror,-Winfinite-recursion]
(same in vtysh/vtysh.c)
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
We can't use if_lookup_prefix() in rip_update_process() because this
function uses prefix_cmp() internally to try matching an interface
address to a static neighbor's address.
Since prefix_cmp() tries to match exact prefixes, if_lookup_prefix()
was always returning NULL.
What we really need here is to use prefix_match(), which checks if
one prefix includes the other (e.g. one /24 interface including a /32
static neighbor's address). The fix then is to replace the call to
if_lookup_prefix() and use if_lookup_address() instead, which uses
prefix_match() internally.
Fixes IxANVL RIP test 17.1
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Refactor a bunch of commands.
* Make hidden configuration items consistent
* Remove duplicate code
* Make unconfig consistent with config
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
When ospf RI commands are entered and we have not turned
on the feature, gracefully tell the user that there is
no going forward.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
If ospf mpls-te has not been turned on via a 'mpls-te on'
dissallow other mpls-te commands from being silently accepted
and ignored.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Signed-off-by: Christian Franke <chris@opensourcerouting.org>
Signed-off-by: Christian Franke <chris@opensourcerouting.org>
Acked-by: Donald Sharp <sharpd@cumulusnetworks.com>
Consolidate the routemap initialization into one
function.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Daniel Walton <dwalton@cumulusnetworks.com>
If a command is put into the VIEW_NODE, it is going into the
ENABLE_NODE as well. This is especially true for show commands.
As such if a command is in both consolidate it down to VIEW_NODE.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
This patch improves zebra,ripd,ripngd,ospfd and bgpd so that they can
make use of 32-bit route tags in the case of zebra,ospf,bgp or 16-bit
route-tags in the case of ripd,ripngd.
It is based on the following patch:
commit d25764028829a3a30cdbabe85f32408a63cccadf
Author: Paul Jakma <paul.jakma@hpe.com>
Date: Fri Jul 1 14:23:45 2016 +0100
*: Widen width of Zserv routing tag field.
But also contains the changes which make this actually useful for all
the daemons.
Signed-off-by: Christian Franke <chris@opensourcerouting.org>
Problem reported that no peers are displayed when the command "show
ip ospf neighbor detail all" is entered. Determined that the problem
was actually that the function only displayed NBMA peers, and since
we rarely (if ever) define NBMA peers, nothing is normally displayed.
Changed the code to display both NBMA and non-NBMA peers, in both the
up and down state. Manual testing attached to the jira ticket.
Ticket: CM-5878
Signed-off-by: Don Slice
Reviewed-by: Daniel Walton
* zclient.c: prefix length on router-id and interface address add
messages not sanity checked. fix.
* */*_zebra.c: Prefix length on zebra route read was not checked, and
clients use it to write to storage. An evil zebra could overflow
client structures by sending overly long prefixlen.
Prompted by discussions with:
Donald Sharp <sharpd@cumulusnetworks.com>
Since recently zebra uses only the ZEBRA_REDISTRIBUTE_* messages
to advertise redistributed routes to its clientes. Now the old
ZEBRA_IPV*_ROUTE_* messages are only used for client->zebra communication.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
The new TE functions will always print out a warning
that TE has not been configured on an interface. This
should be a debug not a warn.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
This is a rather large mechanical commit that splits up the memory types
defined in lib/memtypes.c and distributes them into *_memory.[ch] files
in the individual daemons.
The zebra change is slightly annoying because there is no nice place to
put the #include "zebra_memory.h" statement.
bgpd, ospf6d, isisd and some tests were reusing MTYPEs defined in the
library for its own use. This is bad practice and would break when the
memtype are made static.
Acked-by: Vincent JARDIN <vincent.jardin@6wind.com>
Acked-by: Donald Sharp <sharpd@cumulusnetworks.com>
[CF: rebased for cmaster-next]
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Signed-off-by: Christian Franke <chris@opensourcerouting.org>
Move over to the new allocation counting added in the previous commit.
(This commit is mostly mechanical.)
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Acked-by: Vincent JARDIN <vincent.jardin@6wind.com>
Entering 'show ip ospf interface json' causes ospf
to crash.
Entering 'show ip ospf interface <intf> json' causes
ospf to crash if intf has no neighbors on the otherside
Modify the code to not crash in these cases.
Ticket: CM-12776
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Daniel Walton <dwalton@cumulusnetworks.com>
Entering 'show ip ospf interface json' causes ospf
to crash.
Entering 'show ip ospf interface <intf> json' causes
ospf to crash if intf has no neighbors on the otherside
Modify the code to not crash in these cases.
Ticket: CM-12776
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Daniel Walton <dwalton@cumulusnetworks.com>
This is an implementation of RFC4970 (Router Information) and
RFC5088 (PCE Capabilities announcement)
* ospfd/Makefile.am: Add new file ospf_ri.c and ospf_ri.h
* ospfd/ospf_opaque.c: Add new Router Capabilities code point
* ospfd/ospf_ri.[c,h]: Implementation of RFC4970 & RFC5088
Signed-off-by: Olivier Dugeon <olivier.dugeon@orange.com>
NOTE: I am squashing several commits together because they
do not independently compile and we need this ability to
do any type of sane testing on the patches. Since this
series builds together I am doing this. -DBS
This new structure is the basis to get new link parameters for
Traffic Engineering from Zebra/interface layer to OSPFD and ISISD
for the support of Traffic Engineering
* lib/if.[c,h]: link parameters struture and get/set functions
* lib/command.[c,h]: creation of a new link-node
* lib/zclient.[c,h]: modification to the ZBUS message to convey the
link parameters structure
* lib/zebra.h: New ZBUS message
Signed-off-by: Olivier Dugeon <olivier.dugeon@orange.com>
Add support for IEEE 754 format
* lib/stream.[c,h]: Add stream_get{f,d} and stream_put{f,d}) demux and muxers to
safely convert between big-endian IEEE-754 single and double binary
format, as used in IETF RFCs, and C99. Implementation depends on host
using __STDC_IEC_559__, which should be everything we care about. Should
correctly error out otherwise.
* lib/network.[c,h]: Add ntohf and htonf converter
* lib/memtypes.c: Add new memeory type for Traffic Engineering support
Signed-off-by: Olivier Dugeon <olivier.dugeon@orange.com>
Add link parameters support to Zebra
* zebra/interface.c:
- Add new link-params CLI commands
- Add new functions to set/get link parameters for interface
* zebra/redistribute.[c,h]: Add new function to propagate link parameters
to routing daemon (essentially OSPFD and ISISD) for Traffic Engineering.
* zebra/redistribute_null.c: Add new function
zebra_interface_parameters_update()
* zebra/zserv.[c,h]: Add new functions to send link parameters
Signed-off-by: Olivier Dugeon <olivier.dugeon@orange.com>
Add support of new link-params CLI to vtysh
In vtysh_config.c/vtysh_config_parse_line(), it is not possible to continue
to use the ordered version for adding line i.e. config_add_line_uniq() to print
Interface CLI commands as it completely break the new LINK_PARAMS_NODE.
Signed-off-by: Olivier Dugeon <olivier.dugeon@orange.com>
Update Traffic Engineering support for OSPFD
These patches update original code to RFC3630 (OSPF-TE) and add support of
RFC5392 (Inter-AS v2) & RFC7471 (TE metric extensions) and partial support
of RFC6827 (ASON - GMPLS).
* ospfd/ospf_dump.[c,h]: Add new dump functions for Traffic Engineering
* ospfd/ospf_opaque.[c,h]: Add new TLV code points for RFC5392
* ospfd/ospf_packet.c: Update checking of OSPF_OPTION
* ospfd/ospf_vty.[c,h]: Update ospf_str2area_id
* ospfd/ospf_zebra.c: Add new function ospf_interface_link_params() to get
Link Parameters information from the interface to populate Traffic Engineering
metrics
* ospfd/ospfd.[c,h]: Update OSPF_OPTION flags (T -> MT and new DN)
* ospfd/ospf_te.[c,h]: Major modifications to update the code to new
link parameters structure and new RFCs
Signed-off-by: Olivier Dugeon <olivier.dugeon@orange.com>
tmp
Use the 'enum nexthop_types_t' instead of
the zebra.h #defines. And remove code from
zebra.h that does not belong there.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Daniel Walton <dwalton@cumulusnetworks.com>
Use with interface command:
interface ppp0
ip ospf area 0.0.0.0
This will enable OSPF on ppp0 with area 0.0.0.0
Remove with "no ip ospf area"
* ospf_vty.c: add "ip ospf area (A.B.C.D|<0-4294967295>)" interface command
* ospfd.c: (ospf_interface_{un,}set) new helper function to enable/disable
OSPF on a specific interface.
(ospf_if_update) 2 possible paths now to deal with interface updates.
Acked-by: Donald Sharp <sharpd@cumulusnetworks.com>
[DL: this restores the tree to deccaf9...]
This reverts commit e723861da1.
The code is from Joakim Tjernlund; this is just to fix the history (and
attribution) of it. The last commit will restore the exact same tree
state.
THIS COMMIT WILL PROBABLY NOT COMPILE.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Remove from ospf the HAVE_OSPF_TE define and just always have
ospf traffic engineering.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Tested-by: NetDEF CI System <cisystem@netdef.org>
(cherry picked from commit 693da6096a28eef5eadeea699771265987b3ec0c)
HAVE_OPAQUE_LSA is used by default and you have to actively turn it off
except that OPAQUE_LSA is an industry standard and used pretty much
everywhere. There is no need to have special #defines for this anymore.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
(cherry picked from commit 36fef5708d074a3ef41f34d324c309c45bae119b)
OpenBSD doesn't support the "ifindex hack" derived from RFC 1724 which
allows an ifindex to be encoded in the imr_interface field (in_addr)
of the ip_mreq structure. OpenBSD also doesn't support the RFC3678
Protocol-Independent socket API extensions, which allows an interface
to be specified by its ifindex. With that said, in OpenBSD we still need
to specify an interface by its IP address. This patch adds an exception
in the multicast sockopt functions to handle this case.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
A few places are using 0 in place of the MTYPE_* argument. The
following rewrite of the alloc tracking won't deal with that, so let's
use MTYPE_TMP instead.
Acked-by: Vincent JARDIN <vincent.jardin@6wind.com>
Acked-by: Donald Sharp <sharpd@cumulusnetworks.com>
[DL: v2: fix XFREE(0, foo) calls too]
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Make it easier to see which bits in *_snmp.c are actually referenced
from non-SNMP parts of the code.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
While the idea for this came the other way around - removing
quagga_time() - using random() is actually a better idea here. It's
seeded by time to begin with, but if ospfd restarts several times in a
short timespan it won't run straight into the same sequence number.
(Should also update the random seed to include microseconds so restarts
within a second use a different seq#)
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
The ctime/mtime fields in ospf_route and start_time field in ospf_master
are written but never read, thus entirely useless. Remove them.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
ospf->lsa_refresher_started is only used in relative timing to itself;
replace with monotonic clock which is appropriate for this.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Upon router-id change, one object that needs to be updated is the "nbr_self"
structure that is created to contain information about the local router and
is used during DR election, among other things. In the past, the code used to
just change the router-id field of this structure. This is actually not
sufficient - the neighbor has to be deleted and re-added into the tree. This
was fixed upstream and the fix is now available in our tree, but those changes
don't work well with prior Cumulus changes to defer updating the router-id
in the OSPF instance until other cleanup has happened.
Fixed code to update the "nbr_self" structure correctly while continuing to
defer the router_id update in the OSPF structure.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ticket: CM-11861
Reviewed By: CCR-4980
Testing Done: Manual, failed test
Added a default log file named /var/log/quagga/Quagga.log to every daemon
to capture log entries if no log file is defined. This also allows the
capture of logged information prior to reading each daemon's config file.
If a log file is defined manually, it will override this default file name.
Ticket: CM-10987
Signed-off-by: Don Slice
Reviewed By: Donald Sharp
Testing Done: Manual testing
ospfd: OSPF should accept "router-id IFNAME"
Added commands in BGP and OSPF where user can specify interface for router-id.
Ticket: CM-5040
Reviewed By: CCR-4908
Testing Done: Manual
Ticket: CM-11256
Signed-off-by: Radhika Mahankali <radhika@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Kanna Rajagopal <kanna@cumulusnetworks.com>
Testing: Unit, PTM smoke, OSPF smoke, BGP Smoke
Issue:
BFD client registrations are not being sent to PTM from BGP/OSPF clients when the quagga clients have no BFD configuration. This can create stale BFD sessions in PTM when BFD is removed from quagga configuration before quagga is restarted.
BFD client de-registrations from BGP/OSPF also go missing sometimes when quagga is restarted. This also will cause stale BFD sessions in PTM.
Root Cause:
BFD client registrations were being sent at the time of BGP/OSPF daemon initialization. But, they were being sent to zebra before the socket connection between zebra and BGP/OSPF was established. This causes the missing BFD client registrations.
BFD client de-registrations are sent from zebra when zebra detects socket close for BGP/OSPF daemons. Based on the timing, the de-registrations may happen after socket between PTM and zebra is closed. This will result in missing de-registrations.
Fix:
Moved sending of BFD client registration messages to zebra connected callback to make sure that they are sent after the BGP/OSPF daemons connect with zebra.
Added BFD client de-registrations for BGP/OSPF to be also sent when zebra daemon gets restart signal. They are sent from the signal handler only if it was not already handled in zebra client socket close callback.
Prior to this change, interface bandwidth could not be defined above 10G. With
the use of higher speed interfaces, the ability to effectively define the path
links was highly impacted. Additionally, the default auto-cost reference-bandwidth
for ospf and ospfv3 was set to 100M, which relects a much earlier time. Changed both
the range of interface bandwidth definitions and reference bandwidths to be up to
100G. Set the default interface bandwidth (if not defined) to 10G to make the ratio
continue to cause a cost of 10 as before. Manual testing as well as ospf-min and
ospf-smoke passed successfully.
Ticket: CM-10756
Signed-of-by: Don Slice
Reviewed-by: Donald Sharp
"no debug ospf packet all detail" does not cancel "debug ospf packet all detail"
due to the code inconsistency in setting/unsetting debug flags.
* ospf_dump.c: added missing flags.
Acked-by: Donald Sharp <sharpd@cumulusnetworks.com>
(cherry picked from commit b075e8728f650b0850e20fdf8dde467440a24b28)
When considering small networks that have extreme requirements on
availability and thus convergence delay, the timers given in the OSPF RFC
seem a little “conservative”, i.e., the delay between accepted LSAs and the
rate at which LSAs are sent. Cisco introduced two commands 'timers throttle
lsa all’ and 'timers lsa arrival’, which allow operators to tune these
parameters.
I have been writing a patch to also support 'timers lsa arrival’ fully and
‘timers throttle lsa all’ (without the throttling part) also in quagga.
* ospf_opaque.c: (ospf_opaque_adjust_lsreq) Odd hack to general OSPF
database exchange but made to act only on opaque LSAs. It's either covering
up bugs in the flooding code or its wrong. If it's covering up bugs, those
would affect all LSAs and should be fixed at a lower layer in ospfd, indeed
perhaps those bugs are long fixed anyway (?). Alternatively, it's just plain
wrong. Nuke.
(ospf_opaque_exclude_lsa_from_lsreq) helper to above, nuke.
* ospf_packet.c: Nuke call to ospf_opaque_adjust_lsreq.
Tested-by: olivier.dugeon@orange.com
* Opaque support contains some kind of hack/optimisation to
origination/flooding to suppress some origins/floods until an opaque LS
Acks are received. Previous versions of the code have already been shown
to have bugs in them (see e16fd8a5, e.g.). It seems over-complex and fragile,
plus its conceptually the wrong place to try implement flooding hacks that,
AFAICT, do not depend particularly on the semantics of opaque LSA.
Nuke.
Tested-by: Olivier Dugeon <olivier.dugeon@orange.com>
Instead of hardcoding some compiler detection, this just checks which
CFLAGS actually work with the compiler specified by the user.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
(cherry picked from commit 3a7e83c2387885075c9ecf1912dd6c9399c6947a)
With commit 1b31375427008aaf980f68d95f50007f600c8ae1
we have a situation where it is possible that the
oi->nbr_self has not been properly set. When
calling the function that sets the nbr_self data
make sure that we have a pointer that works for it.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
ospfd keeps a list of neighbor routers for each configured interface. This
list is indexed using the neighbor router id in case of point-to-point and
virtual link types, otherwise the list is indexed using the neighbor's
source IP (RFC 2328, page 96). The router adds itself as a "pseudo" neighbor
on each link, and also keeps a pointer called (nbr_self) to the neighbor
structure. This takes place when the interface is first configured. Currently
ospfd adds this pseudo neighbor before the link parameters are fully configure,
including whether the link type is point-to-point or virtual link. This causes
the pseudo neighbor to be always indexed using the source IP address regardless
of th link type. For point-to-point and virtual links, this causes the lookup
for the pseudo neighbor to always fail because the lookup is done using the
router id whereas the neighbor was added using its source IP address.
This becomes really problematic if there is a state change that requires a
rebuild of nbr_self, changing the router id for example. When resetting
nbr_self, the router first tries to remove the pseudo neighbor form its
neighbor list on each link by looking it up and resetting any references to it
before freeing the neighbor structure. since the lookup fails to retrieve any
references in the case of point-to-point and virtual links the neighbor
structure is freed leaving dangling references to it. Any access to the
neighbor list after that is bound to stumble over this dangling pointer
causing ospfd to crash.
Signed-off-by: Jafar Al-Gharaibeh <jafar@atcorp.com>
Tested-by: NetDEF CI System <cisystem@netdef.org>
(cherry picked from commit bb01bdd740339b0c07d8ed0786811801b2a79192)
There were some (inconsequential) warnings about uninitialised use of
variables. Also, in one case, sub-structs were mixed in initialisation,
which doesn't quite work as intended.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
On higher warning levels, compilers expect %p printf arguments to be
void *. Since format string / argument warnings can be useful
otherwise, let's get rid of this noise by sprinkling casts to void *
over printf calls.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Since we can't assume time_t to be long, int, or even long long, this
consistently uses %lld/long long (or %llu/unsigned long long in a few
cases) to print time_t/susecond_t values. This should fix a bunch of
warnings, on NetBSD in particular.
(Unfortunately, there seems to be no "PRId64" style printing macro for
time_t...)
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
(cherry picked from commit ef008d2f8dc8f7160d8a3d24a15f2fad79ef3242)
INCLUDES in configure.ac was not used at all, and INCLUDES in
Makefile.am is supposed to be AM_CPPFLAGS these days.
Reduces warnings spewed during bootstrap/autoreconf.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Acked-by: Greg Troxel <gdt@ir.bbn.com>
Acked-by: Feng Lu <lu.feng@6wind.com>
Acked-by: Paul Jakma <paul@jakma.org>
(cherry picked from commit 237aac56960575f6ad2451ba2796d94bd5ae4b33)
* ospf_spf.h: use an enum for the reason, and have it as a new argument to
ospf_spf_calculate_schedule, no need for additional call, and let compiler
do the checking.
* ospf_spf.c: format changes - Quagga coding style places function names
at the start of a new line, for easy grepping for definition.
(ospf_spf_calculate_timer) Change the log format of SPF execution time to
avoid ginormous line, and make logging conditional, as is the norm.
(cherry picked from commit b6eef003e1a79471addea0b01853b08aed812cc8)
Conflicts:
ospfd/ospf_spf.c
According to RFC 2328, section 10.5 PointToPoint neighbors
should be identified by router ID instead of source IP address.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
(cherry picked from commit 5c1791f28e2e831e4e9b92c3c2f7d8ed832cb968)
libospf and libospfclient both need libzebra, so they should link
against it. The days of libtool propagating upwards such dependencies
are nearing their end...
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
(cherry picked from commit d8d5c60ecfab4dd609a07b4baa00d735f59002b9)
The ospfNbrState in the ospf trap sent from ospfd shows an incorrect state.
For example, when the connection goes down, the ospfNbrState in the trap is
sent as '8' (full). When the connection is reestablished, the state is sent
as '7' (loading).
The reason seems to be that the trap is sent from nsm_notice_state_change()
before the state is actually updated by calling nsm_change_state().
After applying the attached patch, the traps are sent with nbrState '1' when
the connection goes down and '8' when it goes back up.
Bugzilla #833https://bugzilla.quagga.net/show_bug.cgi?id=833
(cherry picked from commit b6404390a713144252b62f49a328315d1952c6d8)
* 94266fa822ba "ospfd: Self nbrs needs to be rebuilt when router ID changes."
deleted the nbr_self, and added it back, but ospf_nbr_add_self doesn't
actually create the nbr_self - it assumes it's already there. Leading
to use after free and crashes after a router-id change.
* ospfd/ospf_neighbor.{c,h}: (ospf_nbr_self_reset) Little helper to reset the
nbr_self correctly.
* ospf_interface.c: (ospf_if_cleanup) moved code to ospf_nbr_self_reset
* ospfd.c: (ospf_router_id_update) Use ospf_nbr_self_reset instead of doing
the reset badly, fixing 94266fa822ba.
(cherry picked from commit c920e510d09c6c4ab63a3da5375009442a950f82)
Some self nbrs are identified by router_id, these needs
to be rebuilt instead of just resetting router ID.
Possibly one could optimize for !(virtual | ptop) links
by doing oi->nbr_self->router_id = router_id instead.
Router ID will change once after startup config has been
read and zebra reports router ID, unless router ID has
been configured in ospf.
(cherry picked from commit 94266fa822baf9b9c9e10ac03ccec8ccf3ce0c98)
* ospf_vty.c: ({no_}ospf_passive_interface_addr_cmd) To a static analyser,
the call to ospf_passive_interface_update can look like uninitialised memory
in addr might be read from. It won't be, as ospf_passive_interface_update
only reads addr if params != IF_DEF_PARAMS, but not clear. Split up the
helper into the two cases to make it clear.
(cherry picked from commit e1bcd4741c24ff990a9413ead9a9e37b80153046)
batch-fix all warnings that come up when enabling AgentX SNMP support.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
(cherry picked from commit dfee58f1d41a2e36c7f5f38a3ef5712224131824)
If opaque-capability is enabled, we must set the O-bit in
the option field of all DD packets. Changing the option
field of DD packets may cause the peer to reset the state
back to ExStart.
Signed-off-by: Feng Lu <lu.feng@6wind.com>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
(cherry picked from commit 86ce951e349fd08d1ba2c66f5f6d07756689422a)
ospfd has issues resynchronising its Opaque LSA DB with neighbours after restart
or interface events. The problem comes from opaque_lsa.c code that blocks
subsequent opaque LSA flooding until the neighbour router acknowledge that, and
removes the old opaque LSA from its LSDB. The bug comes from the fact that the
lock is never release, thus avoiding subsequent opaque LSA flooding.
More detail about the bugs and its solution is describeid in file
doc/te-link-params.md
Signed-off-by: Olivier Dugeon <olivier.dugeon@orange.com>
(cherry picked from commit 149210656045c363d8f59b97ad9251b0c06a15df)
This looks fishy in ospf_make_md5_digest()
if (list_isempty (OSPF_IF_PARAM (oi, auth_crypt)))
auth_key = (const u_int8_t *) "";
...
MD5Update(&ctx, auth_key, OSPF_AUTH_MD5_SIZE);
auth_key points to a "" string of len 1 which is a lot
smaller that OSPF_AUTH_MD5_SIZE. Is this intentional to
get some random data or just a plain bug?
Anyone using MD5 should have a closer look and decide
what to do.
Acked-by: Feng Lu <lu.feng@6wind.com>
(cherry picked from commit ea2a598411cc7bd20456849e56bbc9e93c9916e7)
Two issues:
1) nbr->oi->ifp->name is an array it would
always evaluate to true.
2) There exist a code path where addr
would be used without initialization.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Daniel Walton <dwalton@cumulusnetworks.com>
Signed-off-by: Daniel Walton <dwalton@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ticket: CM-10948
The previous formula for calculating delay was:
delay = OSPF_LS_REFRESH_TIME - LS_AGE (lsa) - OSPF_LS_REFRESH_JITTER
+ (random () % (2*OSPF_LS_REFRESH_JITTER));
If LS_AGE() is 0 we get:
delay = 1800 - 0 - 60 + (random() % 2*60)
So delay will be 1740 + 0..120, so we could easily pick a delay that is
greater than OSPF_LS_REFRESH_TIME (1800). For the normal case where
we hit this else the LS_AGE will be > 0 so that reduces the chances of
delay being greater than 1800.
Signed-off-by: Daniel Walton <dwalton@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ticket: CM-10088
When we pulled this patch from upstream there was one spot where we
incorrectly used min_ls_interval (5s) instead of min_ls_arrival (1s).
commit ac7424f9de
Author: Michael Rossberg <michael.rossberg@tu-ilmenau.de>
Date: Mon Jul 27 21:05:44 2015 +0200
configuration options for faster OSPF convergence
Allow configuration of faster OSPF convergence via the
min_ls_interval and min_ls_arrival timer lengths.
This patch was originated by Michael, and cross-ported
to Cumulus's Quagga.
Signed-off-by: Daniel Walton <dwalton@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ticket: CM-10960
The timer is in seconds and was being divided by 1000 instead of
multiplying by 1000 when converting to ms.
CM-10680
Issue: When BGP daemon is stopped, all the BGP BFD sessions are not getting deleted from PTM.
Root cause: BGP daemon stop causes BFD de-register message to be sent for every peer on which BFD is enabled. But, all the de-register messages from bgpd to zebra are not processed before the socket close. This results in some stale BGP BFD sessions.
Fix: Support for client de-register message has been added in PTM/BFD. Changes in Quagga to support BFD client de-registrations:
− The BFD clients de-registration is sent directly from zebra daemon when zebra client (bgpd, ospfd and ospf6d) socket close is detected.
− Introduced a BFD flag for the zebra clients to prevent BFD de-registration messages from being sent to zebra daemon when the client is shutting down. This reduces the BFD messaging.
CM-10540
Issue: Invalid ptm status “fail” instead of “n/a” being displayed for VRF interfaces.
Root cause: ptm status is not being initialized to “unknown” status when VRF interface is added or changed. The uninitialized value is ‘0’ which is the value for “fail”
Fix: Initialized the ptm status to the correct value.
Signed-off-by: Radhika Mahankali <radhika@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Kanna Rajagopal <kanna@cumulusnetworks.com>
Ticket: CM-10680, CM-10540
Reviewed By: CCR-4653
Testing Done: PTM smoke, BGP smoke and ptmd_test.py:TestMultipleAddrsIntfOspfBgp
We want the ability to start up quagga in a varied set of
environments. This needs to be done in SysV and systemd
startups. As such refactor the code to allow us to
allow end users to easily switch between the two
sysV:
edit the /etc/quagga/daemons file
service quagga [start|stop|reload|restart]
Systemd:
edit the /etc/quagga/daemons file
systemctl [start|stop|reload|restart] quagga
Ticket: CM-10634
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Daniel Walton <dwalton@cumulusnetworks.com>
Changed interaction between zebra and routing protocols so that they correctly
fill in the vrf_iflist even for vrfs they're not responsible for. In that way,
when they get callbacks from zebra they can correctly understand whether they need
to create them or not.
Ticket: CM-10427
Signed-off-by: Don Slice
Reviewed-by:
Change-Id: Iff33d70089d1393bf3e9c757d9e9faf134699121
Signed-off-by: kitty <khiruthigai.balasubramanian@hpe.com>
Tested-by: NetDEF CI System <cisystem@netdef.org>
Acked-by: Donald Sharp <sharpd@cumulusnetworks.com>
The file if.c has a iflist that had the list of interfaces
in the default vrf. Remove this variable and replace
with a vrf_iflist lookup on the default vrf where it
was used.
Additionally, modify ptm code to iterate over all vrf's
when enabling ptm.
Ticket: CM-10338
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Don Slice <dslice@cumulusnetworks.com>
Reviewed-by: Radhika Mahankali <radhika@cumulusnetworks.com>
bfd was receiving a callback with an interface name string
but was ignoring the passed in vrf to find the ifp pointer.
This commit fixes that code path in bfd.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Radhika Mahankali <radhika@cumulusnetworks.com>
This reverts commit a7928d3ac4.
This code change breaks allot of tests that have hard coded the
distance. We'll unrevert this after the 3.0 release window.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
All daemons changed to flag an interface that has been moved to a vrf as DELETED instead of INTERNAL.
When they were flagged as IFINDEX_INTERNAL, ospf, rip, and isis would re-install them in the default
assuming that they were being "pre-defined" before the kernel definitions.
Ticket: CM-9265
Signed-off-by: Don Slice
Reviewed-by: Donald Sharp
Change-Id: Iff33d70089d1393bf3e9c757d9e9faf134699121
Signed-off-by: kitty <khiruthigai.balasubramanian@hpe.com>
Tested-by: NetDEF CI System <cisystem@netdef.org>
Acked-by: Donald Sharp <sharpd@cumulusnetworks.com>
This construct:
struct ospf *ospf = vty->index;
if (!ospf)
return CMD_SUCCESS;
Is present throughout the entire ospfd code base. The command:
distance ospf external 255
Is not protected by this construct. I added this construct
to the command and in addition did a quick search to find
any others not protected and to protect them.
Ticket: CM-9725
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Don Slice <dslice@cumulusnetworks.com>
Ticket: CM-7615, CM-7773
Reviewed By: CCR-3610, CCR-3708
Testing Done: Unit, BGP Smoke and OSPF Smoke
Changes (70790261926b17200c8c9377c4576cd3b486fcef) ported from 2.5
Issue (related to CM-7615): 1. CM-7615: There is mismatch in the client name between ptm display of client BFD sessions and the zebra logs. For example, if bgpd added BFD session, zebra logs will show the client as “bgp” but the ptm display will show it as “quagga”
2. Bigger problem is when 2 clients (for example OSPF and BGP) from Quagga register for same BFD session and only one client de-registers the BFD session. This results in BFD session deletion from PTM even though other client still has the BFD registration.
Root Cause: Even though BGP, OSPF and OSPF6 are 3 different clients from Quagga that are trying to register/deregister BFD sessions with PTM, all 3 are represented as one client “quagga” from zebra. This makes it hard for PTM/BFD to distinguish between all three when BFD peer registration/deregistration happens from the clients.
Fix: Send the actual client name bgp, ospf or ospf6 from zebra with BFD reg/dereg messages instead of one unified client name “quagga”
CM-7773: BFD sessions are not getting cleaned from PTM even though no BGP peering exists in Quagga.
Root Cause: PTM cleans up stale BFD sessions from a client when it finds a change in seq id advertised by the client. But, if PTM never detects a change in the seq id then the stale BFD sessions never get cleaned up. The test restarts the quagga without saving the configuration, which results in no BGP peering. No BGP peers are registered with PTM after restart and PTM does not detect a client seq id change resulting in stale BFD sessions.
Fix: New client registration message was added in PTM. Every client that is interested in BFD monitoring will register with PTM with the client seq id. Client will register with a different seq id (typically pid) every time it restarts. This will help in detecting the change in seq id and cleanup of stale BFD sessions for a client.
Code Changes: To support the new client registration message following changes have been made
- Added support for client registration messaging in zebra for sending messages to PTM.
- Added support for client registration messaging between zebra and clients (BGP, OSPF and OSPF6) in BFD library.
- Expanded the reg/de reg peer messaging between zebra and clients to support client specific seq id to distinguish between multiple clients registering for BFD peer rather than one “quagga” client.
- Changes in bgpd, ospfd and ospf6d to send client registrations at the time of daemon initialization and on receiving BFD peer replay message.
If we are attempting to redistribute from a MI ospf
then when should only check for the non MI case if
instance was not passed in.
Ticket: CM-9543
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Daniel Walton <dwalton@cumulusnetworks.com>
A recent modification accidently removed the 'no XXXX'
form of some commands that cl-ospf depended on.
Tickets: CM-9481
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Daniel Walton <dwalton@cumulusnetworks.com>
Signed-off-by: Daniel Walton <dwalton@cumulusnetworks.com>
Reviewed-by: Don Slice <dslice@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ticket: CM-9285
Clients (BGP, OSPF etc.) register with Zebra for information about
a VRF such as Router ID, interfaces and redistribution. Add API to
support unregister also which is required for the non-default VRF.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ticket: CM-9128
Reviewed By: CCR-4098
Testing Done: Manual testing
Modify the daemons to integrate with systemd, if it is enabled via configure,
and to notify systemd that they are running/stopping and to send watch
notifications.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
During CR for nexthop upstream it was noticed that usage
of prefix2str was not consistent. This fixes this problem
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
The json keyword was being read incorrectly.
Basically some commands read a variable # of arguments
and in ospf the command values were being placed into
argc and argv. With a variable # of arguments their
existed a possibility that less arguments would be read
from the cli than were being tested for in the command function
handler. This caused core dumps in some situations.
All code to read to decide to use the json keyword has
been centralized through a function and all code
converted to use it, irrelevant if it exhibited the bug
Ticket: CM-8278
Reviewed by: CCR-3830
Testing: OSPF no longer crashes and all other test suites still run
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Zebra already knows if an interface is unnumbered or not. This
is communicated to OSPF.
OSPF would only send a NEXTHOP_TYPE_IPV4_ONLINK *if* the path
was unnumbered, which it learns from Zebra.
As such, Have OSPF use the normal NEXTHOP_TYPE_IPV4_IFINDEX
type for unnumbered paths. In Zebra, if the ifindex recieved
is unnumbered then assume that the link is NEXTHOP_FLAG_ONLINK.
Ticket: CM-8145
Reviewed-by: CCR-3771
Testing: See bug
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
When there is an OSPF missconfiguration, do not zlog_warn the fact
as that it would quickly overwhelm any log file.
Ticket: CM-7534
Reviewed by: CCR-3756
Testing: See bug
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
The API messages are used by zebra to exchange the interfaces, addresses,
routes and router-id information with its clients. To distinguish which
VRF the information belongs to, a new field "VRF ID" is added in the
message header. And hence the message version is increased to 3.
* The new field "VRF ID" in the message header:
Length (2 bytes)
Marker (1 byte)
Version (1 byte)
VRF ID (2 bytes, newly added)
Command (2 bytes)
- Client side:
- zclient_create_header() adds the VRF ID in the message header.
- zclient_read() extracts and validates the VRF ID from the header,
and passes the VRF ID to the callback functions registered to
the API messages.
- All relative functions are appended with a new parameter "vrf_id",
including all the callback functions.
- "vrf_id" is also added to "struct zapi_ipv4" and "struct zapi_ipv6".
Clients need to correctly set the VRF ID when using the API
functions zapi_ipv4_route() and zapi_ipv6_route().
- Till now all messages sent from a client have the default VRF ID
"0" in the header.
- The HELLO message is special, which is used as the heart-beat of
a client, and has no relation with VRF. The VRF ID in the HELLO
message header will always be 0 and ignored by zebra.
- Zebra side:
- zserv_create_header() adds the VRF ID in the message header.
- zebra_client_read() extracts and validates the VRF ID from the
header, and passes the VRF ID to the functions which process
the received messages.
- All relative functions are appended with a new parameter "vrf_id".
* Suppress the messages in a VRF which a client does not care:
Some clients may not care about the information in the VRF X, and
zebra should not send the messages in the VRF X to those clients.
Extra flags are used to indicate which VRF is registered by a client,
and a new message ZEBRA_VRF_UNREGISTER is introduced to let a client
can unregister a VRF when it does not need any information in that
VRF.
A client sends any message other than ZEBRA_VRF_UNREGISTER in a VRF
will automatically register to that VRF.
- lib/vrf:
A new utility "VRF bit-map" is provided to manage the flags for
VRFs, one bit per VRF ID.
- Use vrf_bitmap_init()/vrf_bitmap_free() to initialize/free a
bit-map;
- Use vrf_bitmap_set()/vrf_bitmap_unset() to set/unset a flag
in the given bit-map, corresponding to the given VRF ID;
- Use vrf_bitmap_check() to test whether the flag, in the given
bit-map and for the given VRF ID, is set.
- Client side:
- In "struct zclient", the following flags are changed from
"u_char" to "vrf_bitmap_t":
redist[ZEBRA_ROUTE_MAX]
default_information
These flags are extended for each VRF, and controlled by the
clients themselves (or with the help of zclient_redistribute()
and zclient_redistribute_default()).
- Zebra side:
- In "struct zserv", the following flags are changed from
"u_char" to "vrf_bitmap_t":
redist[ZEBRA_ROUTE_MAX]
redist_default
ifinfo
ridinfo
These flags are extended for each VRF, as the VRF registration
flags. They are maintained on receiving a ZEBRA_XXX_ADD or
ZEBRA_XXX_DELETE message.
When sending an interface/address/route/router-id message in
a VRF to a client, if the corresponding VRF registration flag
is not set, this message will not be dropped by zebra.
- A new function zread_vrf_unregister() is introduced to process
the new command ZEBRA_VRF_UNREGISTER. All the VRF registration
flags are cleared for the requested VRF.
Those clients, who support only the default VRF, will never receive
a message in a non-default VRF, thanks to the filter in zebra.
* New callback for the event of successful connection to zebra:
- zclient_start() is splitted, keeping only the code of connecting
to zebra.
- Now zclient_init()=>zclient_connect()=>zclient_start() operations
are purely dealing with the connection to zbera.
- Once zebra is successfully connected, at the end of zclient_start(),
a new callback is used to inform the client about connection.
- Till now, in the callback of connect-to-zebra event, all clients
send messages to zebra to request the router-id/interface/routes
information in the default VRF.
Of corse in future the client can do anything it wants in this
callback. For example, it may send requests for both default VRF
and some non-default VRFs.
Signed-off-by: Feng Lu <lu.feng@6wind.com>
Reviewed-by: Alain Ritoux <alain.ritoux@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Donald Sharp <sharpd@cumulusnetworks.com>
Conflicts:
lib/zclient.h
lib/zebra.h
zebra/zserv.c
zebra/zserv.h
Conflicts:
bgpd/bgp_nexthop.c
bgpd/bgp_nht.c
bgpd/bgp_zebra.c
isisd/isis_zebra.c
lib/zclient.c
lib/zclient.h
lib/zebra.h
nhrpd/nhrp_interface.c
nhrpd/nhrp_route.c
nhrpd/nhrpd.h
ospf6d/ospf6_zebra.c
ospf6d/ospf6_zebra.h
ospfd/ospf_vty.c
ospfd/ospf_zebra.c
pimd/pim_zebra.c
pimd/pim_zlookup.c
ripd/rip_zebra.c
ripngd/ripng_zebra.c
zebra/redistribute.c
zebra/rt_netlink.c
zebra/zebra_rnh.c
zebra/zebra_rnh.h
zebra/zserv.c
zebra/zserv.h
These are about to be touched and there's no point in other code
touching into prefix list's internas. Add some isolation.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Later, an interface will belong to a specific VRF, and the interface
initialization will be a part of the VRF initialization. So now call
if_init() from vrf_init(), and if_terminate() from vrf_terminate().
Daemons have the according changes:
- if if_init() was called or "iflist" was initialized, now call
vrf_init() instead;
- if if_terminate() was called or "iflist" was destroyed, now call
vrf_terminate() instead.
Signed-off-by: Feng Lu <lu.feng@6wind.com>
Reviewed-by: Alain Ritoux <alain.ritoux@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Vincent JARDIN <vincent.jardin@6wind.com>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Conflicts:
bgpd/bgp_main.c
pimd/pim_iface.c
pimd/pim_iface.h
pimd/pim_main.c
pimd/pimd.c
Ticket: CM-6768
Reviewed By: CCR-3207
Testing Done: bgpsmoke, smoke, topo to create failure
Redistributing routes goes through a del/add cycle whenever a redistributed
is updated. This del/add cycle causes disruption by causing traffic loss
for brief/long periods of time(6-8 s in case of OSPF). The modifications in
this patch remove the del/add cycle to ensure that this disruption doesn't
happen.
Also fixed sending no forwarding address when announcing IPv4 routes with IPv6
nexthops, and sending nexthop only when there is a single path.
Signed-off-by: Dinesh G Dutt <ddutt@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Ticket: CM-7388
Reviewed By: Donald, Vivek
Testing Done: Cherry picking from 2.5.4, no testing on 3.0 yet
OSPF needs to handle the previously added redist update/raplace semantics.
Update has no new message type, it comes as ADD message.
zclient.c depended upon link time inclusion of a
extern struct thread_master *master. This is a violation of the
namespace of the calling daemon. If a library needs the pointer
pass it in and save it for future use.
This code change also makes the zclient code consistent with
the other lib functions that need to schedule work on your behalf
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ticket:
Reviewed By: CCR-3335
Testing Done: bgpsmoke, ENHE tests etc.
Add support for filtering routes from upper layer protocols to zebra
via route-maps for IPv6. The same functionality already existed for
IPv4.
In addition, add support for setting source of routes via IPv6 protocol
map.
Signed-off-by: Dinesh G Dutt <ddutt@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Vivek Venkataraman <vivek@cumulusnetworks.com>
Reviewed-by: Vipin Kumar <vipin@cumulusnetworks.com>
Ticket:CM-6802, CM-6952
Reviewed By: Donald, Kanna
Testing Done:
Double commit of b76943235e09472ec174edcf7204fc82d27fe966 from br2.5. But, manually resolved all the compilation errors. Also, modified the shows to support the json format which was not supported in br2.5.
CM-6802 – Currently, BFD session status can be monitored only through ptmctl. There is no way to check the BFD status of a peer/neighbor through Quagga. Debugging becomes easier if BFD status is shown in Quagga too. BFD status is relevant when it is shown against the BGP peer/OSPF neighbor. For, this following code changes have been done:
- Only down messages from PTM were being propagated from Zebra daemon to clients (bgpd, ospfd and ospf6d). Now, both up and down messages are redistributed to the clients from zebra. BFD status field has been added to the messaging. Handling of BFD session up messages has been added to the client code. BGP/OSPF neighbor is brought down only if the old BFD session status is ‘Up’ to handle extra/initial down messages.
- BFD status and last update timestamp fields have been added to the common BFD info structure. Also, common show functions for showing BFD information have been added to BFD lib.
- Modified the BGP neighbor show functions to call common BFD lib functions.
- For ospf and ospf6, BFD information was maintained only at interface level. To show BFD status per neighbor, BFD information has been added at neighbor level too. “show ip ospf interface”, “show ip ospf neighbor detail”, “show ipv6 ospf6 interface” and “show ipv6 ospf6 neighbor detail” output have been modified to show BFD information.
CM-6952 - IBGP peers were always assumed to be multi-hop since there was no easy way to determine whether an IBGP peer was single hop or multihop unlike EBGP. But, this is causing problem with IBGP link local peers since BFD doesn't allow multihop BFD session with link local IP addresses. Link local peers were discovered when the interface peering was enabled. Interface peering is always singlehop. So, added checks to treat all interface based peers as single hop irrespective of whether the peer is IBGP or EBGP.
Ticket: CM-6520
Reviewed By: Daniel Walton <dwalton@cumulusnetworks.com>
Reviewed By: Donald Sharp <sharpd@cumulusnetworks.com>
Signed-off-By: Morgan Stewart <morgan@cumulusnetworks.com>
Testing Done: Manual testing and smoketested
Whenever some sort of output is encountered, added a json version with
proper logic as well.
Allow configuration of faster OSPF convergence via the
min_ls_interval and min_ls_arrival timer lengths.
This patch was originated by Michael, and cross-ported
to Cumulus's Quagga.
Signed-off-by: Michael Rossberg <michael.rossberg@tu-ilmenau.de>
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ticket: Trivial
Reviewed by: Trivial
Testing: arm/powerpc/amd64 targets now build
Apparently we have a arm build. Who knew? This fixes the compile warnings/errors
produced when you compile a arm build with -Werror.
OSPF BFD command enhancement to configure BFD parameters (detect multiplier, min rx and min tx).
interface <if-name>
ip ospf bfd <detect mult> <min rx> <min tx>
This patch also adds BFD support for IPv6 OSPF. ospf6d will dynamically register/deregister IPv6 neighbors with BFD for monitoring the connectivity of the neighbor. Neighbor is registered with BFD when 2-way adjacency is established and deregistered when adjacency goes down if the BFD is enabled on the interface through which the neighbor was discovered.
OSPF6 BFD command added to configure BFD and parameters (detect multiplier, min rx and min tx).
interface <if-name>
ipv6 ospf6 bfd <detect mult> <min rx> <min tx>
Signed-off-by: Radhika Mahankali <radhika@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Kanna Rajagopal <kanna@cumulusnetworks.com>
This patch also adds BFD multihop support for BGP. Whether a peer is multi-hop or single hop is determined internally. All IGP peers are considered as multi-hop peers. EBGP peers are considered as single hop unless configured as multi-hop.
BGP BFD command enhancement to configure BFD parameters (detect multiplier, min rx and min tx).
router bgp <as-number>
neighbor <name/ip-address> bfd <detect mult> <min rx> <min tx>
Signed-off-by: Radhika Mahankali <radhika@cumulusnetworks.com>
Reviewed-by: Dinesh G Dutt <ddutt@cumulusnetworks.com>
Reviewed-by: Vipin Kumar <vipin@cumulusnetworks.com>
Reviewed-by: Kanna Rajagopal <kanna@cumulusnetworks.com>
Table-id argument support wasnt complete, used the [proto, instance]
combination changes that were done for OSPF multi-instance. In this case
its 'table <table-id>' just like it was 'ospf <instance-id>'
ospfd: virtual links fix
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by:
Basically ZEBRA_INTERFACE_LINKDETECTION is set to on by default now.
Virtual links are failing to identify as up because of this code change.
Modify ospf to set the flag as appropriate
ospf: Fix cli issues with timers throttle spf and no ip ospf authentication...
When entering no timers throttle spf there was no way to specify the delay, hold
time and max hold time so the command was rejected. This is useful for automated
processes that take currently entered cli to remove the cli.
When entering no ip ospf authentication most forms of the command were being
ignored, this fixes that as well.
Signed-off-by: Donald Sharp <sharpd at cumulusnetworks.com>
Reviewed-by:
At the minimum, the OSPF_LSA_SELF logic isnt foolproof, and it may hit assert
in ospf_refresh_unregister_lsa on a router-id change.
Once OSPF has created and flooded LSAs, its not a good idea to change
router-id inline. Tying it to restart has at least two benefits:
- Implementation can remain sane by not having to re-adjust neighbors and LSAs,
based on the new router-id.
- Works as a deterrent for the user to not meddle with the router-id unless
really needed.
is executed, then the init.d/quagga script doesnt wait more than 120 seconds
for the daemon do stop, worse, it goes ahead and starts the new daemon
regardless. This can result into two ospfd processes running on the same config.
Which leads to many issues including but not limited to high cpu usage.
Thats because the two processes are mixing packets on adjancencies thus
causing churn on the box and network.
As long as OSPF is able to reliably send the max-metric router-lsa before
exiting thats mostly good enough for this purpose anyways.
As a solution to this situation, bringing the maximum configurable value of
the on-shutdown timer below the maximum retry to stop a daemon in init.d/quagga
Notes: This may not be an upstreamable patch, still we needed to find
a solution for init.d/quagga and this command this co-exist.
9.5 Sending Hello packets
Hello packets are sent out each functioning router interface.
They are used to discover and maintain neighbor
relationships.[6] On broadcast and NBMA networks, Hello Packets
are also used to elect the Designated Router and Backup
Designated Router.
The format of an Hello packet is detailed in Section A.3.2. The
Hello Packet contains the router's Router Priority (used in
choosing the Designated Router), and the interval between Hello
Packets sent out the interface (HelloInterval). The Hello
Packet also indicates how often a neighbor must be heard from to
remain active (RouterDeadInterval). Both HelloInterval and
RouterDeadInterval must be the same for all routers attached to
a common network. The Hello packet also contains the IP address
mask of the attached network (Network Mask). On unnumbered
point-to-point networks and on virtual links this field should
be set to 0.0.0.0.
Signed-off-by: Vipin Kumar <vipin@cumulusnetworks.com>
Reviewed-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Dinesh G Dutt <ddutt@cumulusnetworks.com>
The problem is that zclient->redist[ZEBRA_ROUTE_MAX] used for storing a
client’s redist state, has no address-family qualification. This means
a client can only store its interest in a protocol (connected, static etc.),
but cant choose IPv4 or ipv6 with that. This hindered implementation on
client sides to manage redistribution of ipv4 and ipv6 both.
BGP's redistribution of protocols like connected/static is one such place.
One fix could be to overload this and flap the redist connection each time
any new afi is added for redist, but that may have side-effects on the
existing afi redist.
The cleaner way is to modify redist data-structure to also take AFI, and adjust
routines that deal with it, so that a client can register for a protocol
redistribution based on the AFI. BGP already maintains redistribution state
based on afi and protocol (bgp->redist[AFI_MAX][ZEBRA_ROUTE_MAX]). This patch
takes care of filling up the gap in zclient/zserv redistribution state to
also use AFI qualification.
Signed-off-by: Vipin Kumar <vipin@cumulusnetworks.com>
Reviewed-by: Daniel Walton <dwalton@cumulusnetworks.com>
Reviewed-by: Dinesh G Dutt <ddutt@cumulusnetworks.com>
LSAcks (for directed acks) are being sent to neighbor's unicast address.
RFC 2328 says:
"The IP destination address for the packet is selected as
follows. On physical point-to-point networks, the IP
destination is always set to the address AllSPFRouters"
Fix is to unconditionally set the destination address for LSAcks over
point-to-point links as AllSPFRouters. Quagga OSPF already has similar
change for OSPF DBD, LSUpdate and LSrequest packets.
Signed-off-by: Vipin Kumar <vipin@cumulusnetworks.com>
Reviewed-by: Daniel Walton <dwalton@cumulusnetworks.com>
Reviewed-by: Dinesh G Dutt <ddutt@cumulusnetworks.com>
——————————————-------------
- etc/init.d/quagga is modified to support creating separate ospf daemon
process for each instance. Each individual instance is monitored by
watchquagga just like any protocol daemons.(requires initd-mi.patch).
- Vtysh is modified to able to connect to multiple daemons of the same
protocol (supported for OSPF only for now).
- ospfd is modified to remember the Instance-ID that its invoked with. For
the entire life of the process it caters to any command request that
matches that instance-ID (unless its a non instance specific command).
Routes/messages to zebra are tagged with instance-ID.
- zebra route/redistribute mechanisms are modified to work with
[protocol type + instance-id]
- bgpd now has ability to have multiple instance specific redistribution
for a protocol (OSPF only supported/tested for now).
- zlog ability to display instance-id besides the protocol/daemon name.
- Changes in other daemons are to because of the needed integration with
some of the modified APIs/routines. (Didn’t prefer replicating too many
separate instance specific APIs.)
- config/show/debug commands are modified to take instance-id argument
as appropriate.
Guidelines to start using multi-instance ospf
---------------------------------------------
The patch is backward compatible, i.e for any previous way of single ospf
deamon(router ospf <cr>) will continue to work as is, including all the
show commands etc.
To enable multiple instances, do the following:
1. service quagga stop
2. Modify /etc/quagga/daemons to add instance-ids of each desired
instance in the following format:
ospfd=“yes"
ospfd_instances="1,2,3"
assuming you want to enable 3 instances with those instance ids.
3. Create corresponding ospfd config files as ospfd-1.conf, ospfd-2.conf
and ospfd-3.conf.
4. service quagga start/restart
5. Verify that the deamons are started as expected. You should see
ospfd started with -n <instance-id> option.
ps –ef | grep quagga
With that /var/run/quagga/ should have ospfd-<instance-id>.pid and
ospfd-<instance-id>/vty to each instance.
6. vtysh to work with instances as you would with any other deamons.
7. Overall most quagga semantics are the same working with the instance
deamon, like it is for any other daemon.
NOTE:
To safeguard against errors leading to too many processes getting invoked,
a hard limit on number of instance-ids is in place, currently its 5.
Allowed instance-id range is <1-65535>
Once daemons are up, show running from vtysh should show the instance-id
of each daemon as 'router ospf <instance-id>’ (without needing explicit
configuration)
Instance-id can not be changed via vtysh, other router ospf configuration
is allowed as before.
Signed-off-by: Vipin Kumar <vipin@cumulusnetworks.com>
Reviewed-by: Daniel Walton <dwalton@cumulusnetworks.com>
Reviewed-by: Dinesh G Dutt <ddutt@cumulusnetworks.com>
Support stubby and totally stubby areas in OSPFv3
Signed-off-by: Dinesh G Dutt <ddutt at cumulusnetworks.com>
Reviewed-by: Pradosh Mohapatra <pmohapat at cumulusnetworks.com>
OSPFv3: Add ABR support and make ECMP > 4.
Signed-off-by: Dinesh G Dutt <ddutt at cumulusnetworks.com>
Signed-off-by: Pradosh Mohapatra <pmohapat at cumulusnetworks.com>
protocols. BGP and OSPF are integrated to respond this BFD session down message
originated in Zebra via ptmd.
BGP and OSPF now have a bfd command, which tells OSPF/BGP to respond to the
BFD session down message.
OSPF:
interface <>
ip ospf bfd
BGP:
router bgp <>
neighbor <> bfd
Please note that these commands don't enable BFD as a protocol. BFD configuration
and paramter tuning are via BFD applicable UI.
Signed-off-by: Vipin Kumar <vipin@cumulusnetworks.com>
Reviewed-by: Shrijeet Mukherjee <shm@cumulusnetworks.com>
Credit
------
A huge amount of credit for this patch goes to Piotr Chytla for
their 'route tags support' patch that was submitted to quagga-dev
in June 2007.
Documentation
-------------
All ipv4 and ipv6 static route commands now have a "tag" option
which allows the user to set a tag between 1 and 65535.
quagga(config)# ip route 1.1.1.1/32 10.1.1.1 tag ?
<1-65535> Tag value
quagga(config)# ip route 1.1.1.1/32 10.1.1.1 tag 40
quagga(config)#
quagga# show ip route 1.1.1.1/32
Routing entry for 1.1.1.1/32
Known via "static", distance 1, metric 0, tag 40, best
* 10.1.1.1, via swp1
quagga#
The route-map parser supports matching on tags and setting tags
!
route-map MATCH_TAG_18 permit 10
match tag 18
!
!
route-map SET_TAG_22 permit 10
set tag 22
!
BGP and OSPF support:
- matching on tags when redistribing routes from the RIB into BGP/OSPF.
- setting tags when redistribing routes from the RIB into BGP/OSPF.
BGP also supports setting a tag via a table-map, when installing BGP
routes into the RIB.
Signed-off-by: Daniel Walton <dwalton@cumulusnetworks.com>
SYMPTOM:
Interface mode OSPF area configuration is not retained after restarting quagga.
Example -
quagga(config)# interface swp49
quagga(config-if)# ip ospf area 0.0.0.0
quagga# sh run
<snip>
interface swp49
ip ospf area 0.0.0.0
ipv6 nd suppress-ra
link-detect
!
quagga# write memory
* Restart quagga at this point*
quagga# sh run
<snip>
interface swp49
ipv6 nd suppress-ra
link-detect
!
ISSUE:
The issue is that the interface mode commands can reach the OSPF process even
before 'router ospf' command that initializes the default OSPF instance, this
is not getting handled properly in OSPF process.
FIX:
Initialize the default OSPF instance during OSPF process initializations, which
is before 'router ospf' command is received in OSPF process. So, when interface
mode command is received, it is guaranteed to have ospf instance to work with.
Other way could be to call ospf_get() instead of ospf_lookup() while processing
the config command callbacks, although OSPF needs to have at least one instance
structure anyways, therefore calling it unconditionally in OSPF initializations
should be fine too.
There could be more elaborate fix(es) possible to handle this, like adding some
ordering mechanism for commands as they are read by a process, or storing the
received command and applying it after the commands its dependent upon are
processed. For the issue at hand, initializing the default instance in main()
serves the purpose well.
Signed-off-by: Vipin Kumar <vipin@cumulusnetworks.com>
Reviewed-by: Dinesh Dutt <ddutt@cumulusnetworks.com>
allows for the node to give the neighbor sufficient time to send back
an acknowledgement before retransmission kicks in.
Signed-off-by: Dinesh G Dutt <ddutt@cumulusnetworks.com>
Reviewed-by: Scott Feldman <sfeldma@cumulusnetworks.com>
Reviewed-by: James Li <jli@cumulusnetworks.com>
calculation to a node should be constructed with the sum of all path
costs (metrics) to the node (pretty simple huh). There is a usage of
metric typified by the "max-metric router-lsa" command in many
networking stacks that allows a router to gracefully "remove" itself
from a topology by advertising the maximum value of metric in it's
router LSAs (16 bits of "1"). In this case, the router will continue
to forward any traffic sent to it while these "max-metric" LSAs are
propagated through the network; at which point, the router can be
taken out of service.
The correct handling of this in ospfd would use this metric as part of
the calculation, disuading other routers from using it for transit
traffic (assuming a better path exits). Unfortunately, the ospfd
behavior is to remove these links from the SPF calculation. This
patch changes the behavior to omit this exception handling.
Signed-off-by: JR Rivers <jrrivers@cumulusnetworks.com>
is able to send out K (=3 by default) packets per thread-write.
Signed-off-by: Ayan Banerjee <ayan@cumulusnetworks.com>
Reviewed-by: JR Rivers <jrrivers@cumulusnetworks.com>
does not access the address in the deletion path
of the interface.
Signed-off-by: Ayan Banerjee <ayan@cumulusnetworks.com>
Reviewed-by: Dinesh G Dutt <ddutt@cumulusnetworks.com>
Compute and display SPF execution statistics
Detailed SPF statistics, all around time spent executing various pieces of SPF
such as the SPF algorithm itself, installing routes, pruning unreachable networks
etc.
Reason codes for firing up SPF are:
R - Router LSA, N - Network LSA, S - Summary LSA, ABR - ABR status change,
ASBR - ASBR Status Change, AS - ASBR Summary, M - MaxAge
Signed-off-by: Dinesh G Dutt <ddutt@cumulusnetworks.com>
Reviewed-by: JR Rivers <jrrivers@cumulusnetworks.com>
Reviewed-by: Scott Feldman <sfeldma@cumulusnetworks.com>
Reviewed-by: Ayan Banerjee <ayan@cumulusnetworks.com>
Quagga sources have inherited a slew of Page Feed (^L, \xC) characters
from ancient history. Among other things, these break patchwork's
XML-RPC API because \xC is not a valid character in XML documents.
Nuke them from high orbit.
Patches can be adapted simply by:
sed -e 's%^L%%' -i filename.patch
(you can type page feeds in some environments with Ctrl-V Ctrl-L)
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Add log messages to lsa_link_broadcast_set so it becomes more
apparent why a particular broadcast interface was added as
transit or stub interface.
Signed-off-by: Christian Franke <chris@opensourcerouting.org>
Acked-by: Feng Lu <lu.feng@6wind.com>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
PROBLEM:
Accurate garbage collection of maxage LSAs. The global OSPF structure has
a maxage_lsa tree - the key to the tree is <ls-id, adv-router> tuple. Suppose
the ABR has multiple areas and has originated some intra-area LSAs. The
key for all those LSAs is the same. The code then ends up in a state where
all but the first LSA do not get cleaned up from the areas' LSDB. A subsequent
event would readvertise those LSAs.
PATCH:
Since the LSA is going to stick around till it actually gets cleaned up by
the maxage_walker, make the LSA pointer as the key. Each distinct LSA that
gets maxage'd then gets added to the tree and will get cleaned up correctly.
Signed-off-by: Pradosh Mohapatra <pmohapat@cumulusnetworks.com>
[CF: Use CHAR_BIT; use uintptr_t; use sizeof(field) instead of sizeof(type)]
Signed-off-by: Christian Franke <chris@opensourcerouting.org>
[DL: this must remain a temporary fix! needs to be redone after 0.99.23]
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Signed-off-by: Christian Franke <chris@opensourcerouting.org>
Acked-by: Feng Lu <lu.feng@6wind.com>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Commit 4de8bf0011 added a return statement to a loop iterating over a
route_table. That loop uses route_top/route_next.
As commit 4de8bf0011 failed to add a route_node_unlock before the
return statement, a reference is leaked when this codepath is taken.
Signed-off-by: Christian Franke <chris@opensourcerouting.org>
Acked-by: Feng Lu <lu.feng@6wind.com>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
ISSUE:
RTA(DR)-----(BackupDR)RTB
RTA advertises a new LSA to RTB, and then flushes the LSA (with setting
the age of the LSA to MaxAge) within 1 second. Then the LSA is deleted
from RTA, while it still exists on RTB with non-MaxAge and can not be
flushed any more.
FIX:
The reason can be explained in below:
a) RTA -- new LSA, #seq=1 --> RTB (RTB will send the delayed Ack in 1s)
b) RTA -- MaxAge LSA, #seq=1 --> RTB (RTB discards it for the MIN_LS_ARRIVAL)
c) RTA <-- Ack for the new LSA, #seq=1 -- RTB (RTA accepts it)
In the step c), ospf_ls_ack() compares the #seq of the entry in the LS-Ack
with that of local MaxAge LSA. The #seq of the two entries are same. So
the Ack is accepted and the LSA is removed from the retransmit-list (while
it should not).
In RFC2328, section 13.7. Receiving link state acknowledgments:
o If the acknowledgment is for the same instance that is <==
contained on the list, remove the item from the list and
examine the next acknowledgment. Otherwise:
where "same instance" does not mean the same #seq. We must call
ospf_lsa_more_recent() to check whether the two instances are same.
Signed-off-by: Feng Lu <lu.feng@6wind.com>
Signed-off-by: Christian Franke <chris@opensourcerouting.org>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
OSPFd only allocates some stub information for loopback interfaces.
This causes a crash when the interface state machine is started on
that interface by configuring a different network type.
It doesn't make much sense to configure the network type of a loopback
interface, therefore, just forbid it.
See also bugzilla #670.
Signed-off-by: Christian Franke <chris@opensourcerouting.org>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
The results from DR election are used when constructing router-LSAs.
E.g. they are used to determine whether a broadcast interface should
be added with a link type of stub interface or transit interface.
Therefore, we should run DR election prior before regenerating LSAs.
Before commit c363d3861b the DR election
was called synchronously prior to router-LSA regeneration which was run
asynchronously.
This fixes bug #761 on the Quagga bugzilla.
Signed-off-by: Christian Franke <chris@opensourcerouting.org>
Acked-by: Feng Lu <lu.feng@6wind.com>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Use the new keyword command style for:
- default-information originate
- distance ospf
- redistribute
Signed-off-by: Christian Franke <chris@opensourcerouting.org>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Add support for keyword commands.
Includes new documentation for DEFUN() in lib/command.h, for preexisting
features as well as new keyword specification.
Signed-off-by: Christian Franke <chris@opensourcerouting.org>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Fixup some DEFUNS with incorrect command strings or mixed up helpstrings.
Signed-off-by: Christian Franke <chris@opensourcerouting.org>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
This patch against the git tree fixes minor typos, some of them possibily
leading to NULL-pointer dereference in rare conditions.
Signed-off-by: Remi Gacogne <rgacogne-github@coredump.fr>
Signed-off-by: Joachim Nilsson <troglobit@gmail.com>
Acked-by: Feng Lu <lu.feng@6wind.com>
Signed-off-by: Dinesh G Dutt <ddutt at cumulusnetworks.com>
Signed-off-by: Ayan Banerjee <ayabaner at gmail.com>
Reviewed-by: Scott Feldman <sfeldma at cumulusnetworks.com>
Reviewed-by: James Li <jli at cumulusnetworks.com>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
MaxAge LSAs are being flushed out only on an event, unlike OSPFv2 where they're flushed out
periodically. This causes certain LSAs to hang around forever, never getting flushed out.
This patch makes flushing out MaxAge LSAs periodic, retriggered after a certain period if
not all MaxAge LSAs were flushed out.
Signed-off-by: Dinesh G Dutt <ddutt at cumulusnetworks.com>
Reviewed-by: Scott Feldman <sfeldma at cumulusnetworks.com>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Rearranging common defs and structures for use betweeen OSPFv2 and
OSPFv3. Created a new file called libospf.h under lib directory to
hold defines that are common between OSPFv2 and OSPFv3 code bases.
[DL: split of defines refactor from timer refactor]
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
VU#229804 reports that, by injecting Router LSAs with the Advertising
Router ID different from the Link State ID, OSPF implementations can be
tricked into retaining and using invalid information.
Quagga is not vulnerable to this because it looks up Router LSAs by
(Router-ID, LS-ID) pair. The relevant code is in ospf_lsa.c l.3140.
Note the double "id" parameter at the end.
Still, we can provide an improvement here by discarding such malformed
LSAs and providing a warning to the administrator. While we cannot
prevent such malformed LSAs from entering the OSPF domain, we can
certainly try to limit their distribution.
cf. http://www.kb.cert.org/vuls/id/229804 for the vulnerability report.
This issue is a specification issue in the OSPF protocol that was
discovered by Dr. Gabi Nakibly.
Reported-by: CERT Coordination Center <cert@cert.org>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
the OSPF API-server (exporting the LSDB and allowing announcement of
Opaque-LSAs) writes past the end of fixed on-stack buffers. This leads
to an exploitable stack overflow.
For this condition to occur, the following two conditions must be true:
- Quagga is configured with --enable-opaque-lsa
- ospfd is started with the "-a" command line option
If either of these does not hold, the relevant code is not executed and
the issue does not get triggered.
Since the issue occurs on receiving large LSAs (larger than 1488 bytes),
it is possible for this to happen during normal operation of a network.
In particular, if there is an OSPF router with a large number of
interfaces, the Router-LSA of that router may exceed 1488 bytes and
trigger this, leading to an ospfd crash.
For an attacker to exploit this, s/he must be able to inject valid LSAs
into the OSPF domain. Any best-practice protection measure (using
crypto authentication, restricting OSPF to internal interfaces, packet
filtering protocol 89, etc.) will prevent exploitation. On top of that,
remote (not on an OSPF-speaking network segment) attackers will have
difficulties bringing up the adjacency needed to inject a LSA.
This patch only performs minimal changes to remove the possibility of a
stack overrun. The OSPF API in general is quite ugly and needs a
rewrite.
Reported-by: Ricky Charlet <ricky.charlet@hp.com>
Cc: Florian Weimer <fweimer@redhat.com>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
An ospf router should accept a new maxage LSA into its lsdb if it has any
neighbors in state Exchange or Loading. ospfd would however only account
for neighbors on the same interface which does not seem to be a valid
optimization.
Signed-off-by: Christian Franke <chris@opensourcerouting.org>
Signed-off-by: Joachim Nilsson <troglobit@gmail.com>
Signed-off-by: David Lamparter <equinox@diac24.net>
ospf_maxage_lsa_remover whould check whether to yield,
but run on anyway.
Signed-off-by: Christian Franke <chris@opensourcerouting.org>
Signed-off-by: Joachim Nilsson <troglobit@gmail.com>
Signed-off-by: David Lamparter <equinox@diac24.net>
commit c81ee5c... "ospfd: Optimize and improve SPF nexthop calculation"
subtly changed semantics of routes calculated over pointopoint links by
removing the nexthop IP address and instead using an ifindex route.
This breaks calculation of AS-Ext routes with a forwarding address since
in ospf_ase_complete_direct_routes() this will be hit:
if (op->nexthop.s_addr == 0)
op->nexthop.s_addr = nexthop.s_addr;
thus turning the route unusable by having an invalid nexthop.
Fix by restoring the nexthop IP on routes over PtP links. This also
allows running multi-access (Ethernet) interfaces in PtP mode again.
This bug is a regression against 0.99.21 and only present in 0.99.22.
Signed-off-by: Christian Franke <chris@opensourcerouting.org>
[patch description and code comments rewritten]
Acked-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Acked-by: James Li <jli@cumulusnetworks.com>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
If configured without opaque LSA support, the old code would incorrectly
associate type 5 LSAs with an area.
Signed-off-by: Christian Franke <chris@opensourcerouting.org>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Stop additional, unnecessary flooding of MaxAge LSAs.
When a MaxAge LSA is installed, if the LSA is prematurely aged or the LSA is
not self-originated, the LSA is flushed. This results in a the LSA being
flooded a second time and in some cases flooded back to the receiver
(unless the receiver is also the advertising router). A MaxAge'd LSA has
already been flooded in ospf_flood() as part of the LSA receive processing
(ospf_ls_upd). A self-originated LSA will be flooded from the originate/refresh
routine. Thus, in the install routine, a MaxAge'd LSA only needs to be added
to the MaxAge LSA list.
Signed-off-by: Dinesh G Dutt <ddutt@cumulusnetworks.com>
Signed-off-by: Scott Feldman <sfeldma@cumulusnetworks.com>
This fix is for Type-4 LS updates handling at a ABR router where
ospf daemon is not distributing Type-4 LS updates with correct LS-Age
after learning about a ASBR router in a ospf network. Because of this
Type-5 LS updates are not learnt in ospf network.
Testing Scenario:
This can be re-produced by restarting the ospfd daemon on DUT
(mentioned in figure below)before the Hello time interval expires
for area 0.0.0.1.
____ _______ ____ _________
| | area: 0.0.0.1 | | area: 0.0.0.0 | | area: 0.0.0.2 | |
| R1 |---------------------|DUT/ABR|---------------------| R2 |------------------| R3/ASBR |
|____| x.x.x.0/24 |_______| y.y.y.0/64 |____| z.z.z.0/24 |_________|
In the above setup when ospfd is restarted (imp:before the Hello interval
at R1 expires) and DUT learns about ASBR router R3 (Type-4) in the
network from R2, but this ls-update is not propagates in area
0.0.0.1. So R1 never comes to know about the ASBR router in the
network, so all the type-5 LS updates coming from R3 are not learnt
by R1. Further if we again restart ospfd daemon it starts working fine.
With the fix given this issue can be resolved.
More Discussion on this is available at:
http://www.gossamer-threads.com/lists/quagga/dev/23892
Signed-off-by: Scott Feldman <sfeldma@cumulusnetworks.com>
A set of patches to clarify some comments as well as cleanup code that was
causing warnings. After these patches, the code can be compiled with
-Wall -Wsign-compare -Wpointer-arith -Wbad-function-cast -Wwrite-strings
-Wmissing-prototypes -Wmissing-declarations -Wchar-subscripts -Wcast-qual
-Wextra -Wno-unused-parameter -Wno-missing-field-initializers
(what is current in trunk plus -Wextra -Wno-unused-parameter
-Wno-missing-field-initializers).
Signed-off-by: Scott Feldman <sfeldma@cumulusnetworks.com>
Since LEGAL_TE_INSTANCE_RANGE() was being passed an unsigned int, a warning
was being thrown due to the compare against >= 0. Since this macro was used
only in one place, I removed the macro for an explict compare against a
constant for the MAX.
Signed-off-by: Scott Feldman <sfeldma@cumulusnetworks.com>
In the original code, negative metrics would be converted successfully by
atoi() and then converted to an unsigned int that would always compare
successfully against >= 0, leaving a large positive metric in the route map.
Signed-off-by: Scott Feldman <sfeldma@cumulusnetworks.com>
Use the correct argument for the protocol lookup in
ospf distribute-list commands.
Signed-off-by: Christian Franke <chris@opensourcerouting.org>
Signed-off-by: Scott Feldman <sfeldma@cumulusnetworks.com>
The ospf_apiserver_enable flag was being cleared _after_ the "-a"
command-line option set it to 1. Move up the initialisation, so
enabling the OSPF API is actually possible.
Reported-by: Rosario Mattera <rosmattera@gmail.com>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Signed-off-by: Scott Feldman <sfeldma@cumulusnetworks.com>
The OSPF RFC (2328) states that the network mask field of a type 4
LSA "is not meaningful and must be zero". OSPFD has been setting
the mask as /32. This patch changes OSPFD to set the mask to 0 per
the RFC
Signed-off-by: Scott Feldman <sfeldma@cumulusnetworks.com>
Reduce the log level for the MaxAge LSA reception when such an LSA does
not exist in the database.
Signed-off-by: Ayan Banerjee <ayan@cumulusnetworks.com>
Reviewed-by: Scott Feldman <sfeldma@cumulusnetworks.com>
Reviewed-by: Nolan Leake <nolan@cumulusnetworks.com>
Signed-off-by: Scott Feldman <sfeldma@cumulusnetworks.com>
Store the MaxAge LSA list in a tree instead of a linked list for efficient access.
Walking the list can be quite inefficient in some large systems and under certain tests.
ospfd maintains the list of LSA's that have been MaxAge'd out in a separate
linked list for removal by a remover/walker thread. When a new LSA is to be
installed, the old LSA is ejected and when it is ejected, the MaxAge LSA list
is traversed to ensure that the old LSA is also removed from this list if it
exists on this list.
When a large number (> 5K) MaxAge LSAs are bombarding the system, walking this
list takes a significant time causing timers to fire and actions to be taken
such as expiring neighbors due to expiry of DeadInterval (especially when timer
is really low, <= 12s), creating a spiral of instability.
By making this MaxAge LSA list be a tree, this problem is mitigated.
Signed-off-by: Dinesh Dutt <ddutt@cumulusnetworks.com>
Reviewed-by: Ayan Banerjee <ayan@cumulusnetworks.com>
Reviewed-by: Scott Feldman <sfeldma@cumulusnetworks.com>
Reviewed-by: Shrijeet Mukherjee <shm@cumulusnetworks.com>
Signed-off-by: Scott Feldman <sfeldma@cumulusnetworks.com>
In the event areas are created at a later point of time with respect
to the playback of the "max-metric router-lsa administrative" command,
those areas do not get into indefinite max-metric mode. This patch is
inteneded to store the configuration and apply it to all future areas
that may be created.
In the process, some other bugs that were there with respect to restart
etc are fixed up.
Tested locally to see that the fix works across multiple
areas and across multiple restarts.
Signed-off-by: Ayan Banerjee <ayan@cumulusnetworks.com>
Reviewed-by: Scott Feldman <sfeldma@cumulusnetworks.com>
Reviewed-by: JR Rivers <jrrivers@cumulusnetworks.com>
Signed-off-by: Scott Feldman <sfeldma@cumulusnetworks.com>
After a SPF run, OSPF deletes routes that have changed in terms of any
metric, type, and/or next-hops and re-adds them. Given that the Zebra-RIB
already support replacement semantics, we suppress deletes for routes
that will be added back again.
This has the following advantages. It reduces the number of IPC messages
between OSPF/Zebra. Also, in the current flow, a batch of route deletes
were followed by a batch of adds even for say a metric change.
With the change, routes are sent as "add" when they are modified. Zebra
already implicitly deletes older routes.
Signed-off-by: Ayan Banerjee <ayan@cumulusnetworks.com>
Reviewed-by: Scott Feldman <sfeldma@cumulusnetworks.com>
Reviewed-by: Dinesh Dutt <ddutt@cumulusnetworks.com>
Signed-off-by: Scott Feldman <sfeldma@cumulusnetworks.com>
* ospfd/ospf_apiserver.c: extra ; causing lookup to fail always
* ospfd/ospf_lsa.c: extra ; causing debug output even when disabled
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Use the array_size() helper macro. Replaces several instances of local
macros with the same definition.
Reviewed-by: Scott Feldman <sfeldma@cumulusnetworks.com>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
ISSUE
When max-metric router-lsa administrative is invoked on an ABR created with...
area <area> range <addr/mask>
the summary LSAs are sent out with 65535 (max-metric) added to the normal cost.
When max-metric router-lsa administrative is invoked on an ABR created with...
area <area> range <addr/mask> cost <cost>
the summary LSAs are sent out with <cost> (the max-metric is ignored). This
second behavior effectively incapacitates the max-metric function.
PATCH
This patch evaluates the state of the router and if it's isolated as a stub
router (rfc3137) via `max-metric router-lsa`, we unconditionally uses the
value of 0xff0000 when advertising summary LSAs.
Signed-off-by: JR Rivers <jrrivers@cumulusnetworks.com>
Signed-off-by: Scott Feldman <sfeldma@cumulusnetworks.com>
Reviewed-by: Ayan Banerjee <ayan@cumulusnetworks.com>
Reviewed-by: Dinesh Dutt <ddutt@cumulusnetworks.com>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
When a range (or sub-range) is deleted, the area is notified by propagating a
MAXAGE LSA. This LSA stays in the database for a while to both insure
propagation as well as in the off chance that it's useful in the near future.
Unfortunately, the ABR algorithm was treating these MAXAGE LSAs as unchanged and
not propagating them within the areas.
Signed-off-by: JR Rivers <jrrivers@cumulusnetworks.com>
Signed-off-by: Scott Feldman <sfeldma@cumulusnetworks.com>
Reviewed-by: Dinesh Dutt <ddutt@cumulusnetworks.com>
Reviewed-by: Shrijeet Mukherjee <shm@cumulusnetworks.com>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
ISSUE
When an area range is created in which there the sub-area has routes that are
smaller than the range, an ABR creates a blackhole route to cover the range.
When the range is removed, the blackhole route is not removed.
--A----B----C---
B is an ABR with A in area 1 and C in area 0. If A advertises `10.2.0.0/30` and
`10.2.0.4/30` and B is configured with `area 0.0.0.1 range 10.2.0.0/29` a
blackhole is created on B (`blackhole 10.2.0.0/29 proto zebra`). When the
area/range is removed via the command line, the blackhole remains in existence
even though the "range" route is removed from area 0 and the individual routes
are propagated.
PATCH
The reason for this behavior is that, prior to this patch, the range is deleted
from the area's list, so when ospf_abr_manage_discard_routes() gets called,
there is nothing to clean up. The patch removes the discard route as part of
the processing of the command line (ospf_area_range_unset()).
Signed-off-by: JR Rivers <jrrivers@cumulusnetworks.com>
Signed-off-by: Scott Feldman <sfeldma@cumulusnetworks.com>
Reviewed-by: Shrijeet Mukherjee <shm@cumulusnetworks.com>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
OVERVIEW
The checksum used in OSPF (rfc2328) is specified in rc905 annex B. There is an
sample implementation in rfc1008 which forms the basis of the quagga
implementation. This algorithm works perfectly when generating a checksum;
however, validation is a bit problematic.
The following LSA (generated by a non-quagga implementation) is received by
quagga and marked with an invalid checksum; however, it passes both the rfc905
and rfc1008 validation checks.
static uint8_t lsa_10_121_233_29[] = {
0x0e, 0x10, 0x02, 0x03,
0x09, 0x00, 0x35, 0x40,
0x0a, 0x79, 0xe9, 0x1d,
0x80, 0x00, 0x00, 0x03,
0x00, 0x8a, 0x00, 0x1c,
0xff, 0xff, 0xff, 0xe0,
0x00, 0x00, 0x36, 0xb0
};
LS Type: Summary-LSA (IP network)
LS Age: 3600 seconds
Do Not Age: False
Options: 0x02 (E)
Link-State Advertisement Type: Summary-LSA (IP network) (3)
Link State ID: 9.0.53.64
Advertising Router: 10.121.233.29 (10.121.233.29)
LS Sequence Number: 0x80000003
LS Checksum: 0x008a
Length: 28
Netmask: 255.255.255.224
Metric: 14000
You'll note that one byte of the checksum is 0x00; quagga would calculate the
checksum as 0xff8a.
It can be argued that the sourcing implementation generates an incorrect
checksum; however, rfc905 indicates that, for 1's complement arithmetic, the
value 255 shall be regarded as 0, thus either values are valid.
EXPLANATION
The quagga ospfd and ospf6d implementations operate by copying the PDU's
existing checksum in a holding variable, calculating the checksum, and comparing
the resulting checksum to the original. As a note, this implementation has the
side effect of modifying the contents of the PDU.
Evaluation of both rfc905 and rfc1008 shows that checksum validation should
involve calculating the sum over the PDU and checking that both resulting C0 and
C1 values are zero. This behavior is enacted in the rfc1008 implementation by
calling encodecc with k = 0 (checksum offset); however, this functionality had
been omitted from the quagga implementation.
PATCH
This patch adds the ability to call the quagga's fletcher_checksum() with a
checksum offset value of 0xffff (aka FLETCHER_CHECKSUM_VALIDATE) which returns
the sum over the buffer (a value of 0 indicates a valid checksum). This is
similar to the mechanism in rfc1008 when called with k = 0. The patch also
introduces ospf_lsa_checksum_valid().
ospf6d had it's own implementation of the fletcher checksum in
ospf6_lsa_checksum(); it's the same algorithm as in fletcher_checksum(). This
patch removes the local implementation in favor of the library's as well as creates
and uses ospf6_lsa_checksum_valid().
quagga's ISIS implementation suffers from the same problem; however, I do not
have the facilities to validate a fix to ISIS, thus this change has been left to
the ISIS maintainers. The function iso_csum_verify() should be reduced to
running the fletcher checksum over the buffer using an offset of 0.
Signed-off-by: JR Rivers <jrrivers@cumulusnetworks.com>
Reviewed-by: Scott Feldman <sfeldma@cumulusnetworks.com>
Reviewed-by: Nolan Leake <nolan@cumulusnetworks.com>
Reviewed-by: Ayan Banerjee <ayan@cumulusnetworks.com>
Reviewed-by: Shrijeet Mukherjee <shm@cumulusnetworks.com>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
This reverts commit 9289c6ff55.
The commit reverted an earlier change which was fixed a bug that caused
black-holes to remote destinations with multiple paths, that could occur
during convergence. Overall, the previous code is more correct.
This corrects the parameters passed to libtool when linking
the shared libraries. The paramter name is -version-info not
-version.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
The patch in bug 330 did two things. It add a return value
whether ospf_nexthop_calculation() failed or not and also
moved the return stmt for 16.1.1 para 5 so now SPF
will fallback to the intervening router when no back links are found
by 16.1.1 para 5. This is wrong and can potentially create black holes
or routing loops according to Dave Katz and Acee Lindem at ospf@ietf.org
Even if the current code could be proved to be harmless in all cases,
it adds substantial extra processing and memory allocations.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
OSPF really needs to specify interface in its routes. Otherwise
ospf may change the wrong route.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
[fixed up some whitespace errors, split patch in two]
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
This is better than a prefix lookup as prefixes may not be
unique, that is, the same prefix can exist on several interfaces.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Maintain router LSA positions in OSPF interface.
Find the OSPF interface in nexthop_calculation using
the position in the router LSA. This is possible because
the only time nexthop_calculation needs to look up interfaces
is when dealing with its own Router LSA.
This has the following advantages:
- Multiple PtP interfaces with the same IP address between two routers.
- Use Unnumbered PtP on just one end of the link.
- Faster OI lookup for the OSPF interface and only
done once for PtoP links.
*ospf_interface.h: (struct ospf_interface) Add storage for
storing router LSA position.
*ospf_interface.c: (ospf_if_lookup_by_lsa_pos)
lookup OSPF I/F in an area using LSA position.
*ospf_lsa.c: (router_lsa_link_set) record Router LSA position.
*ospf_spf.c: (ospf_spf_next) Count and pass along lsa position.
(ospf_nexthop_calculation) Add lsa position argument.
call ospf_if_lookup_by_lsa_pos() for OSFP interface handle.
Clean up and remove all calls ospf_if_is_configured() the
rest. Adjust a few debug logs.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
This was found in scale testing at OSR; ospfd is adding the same link
over and over again to the SPF tree. This fix prevents the resulting
memory corruption from happening and adds a debug message to track
occurence of this issue and/or confirm a proper fix.
(This version was improved by Scott Feldman over the earlier RFC.)
* ospfd/ospf_spf.c: (ospf_spf_add_parent) loop over existing vertices
and refuse to add duplicates.
Tested-by: Martin Winter <mwinter@opensourcerouting.org>
Signed-off-by: Scott Feldman <sfeldma@cumulusnetworks.com>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Most table handlers do not expect to be given an OID whose prefix is
outside what they can handle. This is not a problem with the SMUX
implementation since it always correct the OID such that the prefix
matches. However, this is not the case for the AgentX
implementation. A new function, smux_header_table() is used to do this
normalization.
smux_trap() signature has been changed to provide appropriate level
information to send SNMPv2 notifications. This includes the addition
of the enterprise OID to use (from which is derived the SNMP trap OID)
and the MIB registry to locate the appropriate function for variable
bindings provided by the trap.
The SMUX implementation has been updated but ignore the provided
enterprise OID. Instead, it still uses the SMUX peer OID to keep
compatibility with previous versions of Quagga. The SMUX
implementation also ignores the provided MIB registry since it uses
smux_get() function to grab the appropriate values. This is not
possible with the AgentX implementation since there is no such
function provided by NetSNMP.
smux_trap() contains an argument whose use appears to be to set
sysUpTime.0/timestamp field in SNMP trap. However, this value is not
used in smux_trap(). Moreover, it is expected that this field is the
value of sysUpTime.0 when the trap was sent and not any other time
related to the trap. To avoid any confusion, we remove this field from
the signature of the function.
The correct method to link to NetSNMP is to use net-snmp-config (which
is like pkg-config). Explicit link to libcrypto is also dropped
(NetSNMP libs are linked to libcrypto, no need to link Quagga to
it). Moreover, @SNMP_INCLUDES@ is dropped because useless. Due to a
bug in configure.ac, it was properly populated.
Some .h files in lib/ are autogenerated. The search path should
include the build directory and the source directory. They usually
match but sometimes, they may be different. For example:
$ mkdir build
$ cd build
$ ../configure
$ make
The old ospf_check_auth() function did two different jobs depending on
AuType. For Null and Simple cases it actually authenticated the packet,
but for Cryptographic case it only checked declared packet size (not
taking the actual number of bytes on wire into account). The calling
function, ospf_verify_header(), had its own set of MD5/checksum checks
dispatched depending on AuType.
This commit makes the packet size check work against the real number of
bytes and moves it to ospf_packet_examine(). All MD5/checksum
verification is now performed in ospf_check_auth() function.
* ospf_packet.c
* ospf_packet_examin(): check length with MD5 bytes in mind
* ospf_verify_header(): remove all AuType-specific code
* ospf_check_auth(): completely rewrite
An OSPFv2 packet with trailing data blocks (authentication and/or
link-local signaling) failed the recently implemented packet length
check, because trailing data length isn't counted in the packet header
"length" field. This commit fixes respective check conditions.
* ospf_packet.c
* ospf_packet_examin(): use "bytesdeclared" instead of "bytesonwire"
This commit ports more packet checks to OSPFv2, in particular, LSA size
verification and Router-LSA link blocks verification.
* ospf_lsa.h: add LSA size macros
* ospf_packet.h: add struct ospf_ls_update
* ospf_packet.c
* ospf_lsa_minlen[]: a direct equivalent of ospf6_lsa_minlen[]
* ospf_router_lsa_links_examin(): new function, verifies trailing
part of a Router-LSA
* ospf_lsa_examin(): new function like ospf6_lsa_examin()
* ospf_lsaseq_examin(): new function like ospf6_lsaseq_examin()
* ospf_packet_examin(): add type-specific deeper level checks
1. The only purpose of "ibuf" argument was to get stream size, which
was always equal to OSPF_MAX_PACKET_SIZE + 1, exactly as initialized
in ospf_new().
2. Fix the packet size check condition, which was incorrect for very
large packets, at least in theory.
This commit ports some of the OSPFv3 packet reception checks
to OSPFv2.
* ospf_packet.c
* ospf_packet_minlen[]: a direct equivalent of ospf6_packet_minlen[]
* ospf_packet_examin(): new function designed after the first part
of ospf6_packet_examin()
* ospf_read(): verify received packet with ospf_packet_examin()
* ospf_packet.h: add convenience macros
The previous commits modified both zebra and bgpd for additional
SAFI field, but not any other routing daemon, which led to zebra
daemon crashing with failed assertion.
* (general) Move functions in headers into files, to be compiled into
shared object files. Remove inline qualifier from functions. Let the
compiler do the work.
* ospf_abr.c
* ospf_abr_nssa_am_elected(): feed "best" instead of "address of best"
into IPV4_ADDR_CMP(), because "best" is a pointer; also, mean s_addr
field of the structures to get better typed pointers
* ospf_packet.c (ospf_recv_packet): FreeBSD, starting from version 10, will not
subtract the IP header size from ip_len.
This is the patch from FreeBSD's ports/net/quagga/files/patch-ospfd__ospf_packet.c,
by Boris Kovalenko.
this replaces most occurences of routing protocol lists by preprocessor
defines from route_types.h. the latter is autogenerated from
route_types.txt by a perl script (previously awk). adding a routing
protocol now is mostly a matter of changing route_types.txt and log.c.
Conflicts:
lib/route_types.awk
All daemons modified to support custom path to zserv
socket.
lib: generalize a zclient connection
zclient_socket_connect added. zclient_socket and
zclient_socket_un were hidden under static expression.
"zclient_serv_path_set" modified.
The old algorithim looked up every node twice as it withdrew
the entry. It looks up entry once in redistribute_withdraw, then
looks it up again info_delete. Use result of first lookup
to do the free directly.
This may explain the slow performance observed in
https://bugzilla.vyatta.com/show_bug.cgi?id=4421
* sockopt.[ch] (setsockopt_ipv4_multicast): ifindex is now mandatory (all
non-ancient OSes can use it anyway), and if_addr parameter (the address
of the interface) is now gone. (setsockopt_ipv4_multicast_if):
IP_MULTICAST_IF processing moved to this new function
* ospf_network.c (ospf_if_add_allspfrouters, ospf_if_drop_allspfrouters,
ospf_if_add_alldrouters, ospf_if_drop_alldrouters, ospf_if_ipmulticast),
rip_interface.c (ipv4_multicast_join, ipv4_multicast_leave,
rip_interface_new): adapt to the new interface
* ospf_route.c: Function ospf_asbr_route_cmp is called uniquely from
ospf_route_cmp() when the flag OSPF_RFC1583_COMPATIBLE is not set.
Therefore, the check that the flag is set doesn't make sense at all
and it can consequently be removed without doing any harm.
Signed-off-by: Alexandre Chappuis <alc@open.ch>
Signed-off-by: Roman Hoog Antink <rha@open.ch>
This vulnerability (CERT-FI #514838) was reported by CROSS project.
The error is reproducible only when ospfd debugging is enabled:
* debug ospf packet all
* debug ospf zebra
When incoming packet header type field is set to 0x0a, ospfd will crash.
* ospf_packet.c
* ospf_verify_header(): add type field check
* ospf_read(): perform input checks early
This vulnerability (CERT-FI #514838) was reported by CROSS project.
When only 14 first bytes of a Hello packet is delivered, ospfd crashes.
* ospf_packet.c
* ospf_read(): add size check
This vulnerability (CERT-FI #514837) was reported by CROSS project.
They have also suggested a fix to the problem, which was found
acceptable.
Quagga ospfd does not seem to handle unknown LSA types in a Link State
Update message correctly. If LSA type is something else than one
supported
by Quagga, the default handling of unknown types leads to an error.
* ospf_flood.c
* ospf_flood(): check return value of ospf_lsa_install()
* ospfd: Refresher logic cleanup broke OSPF opaque, which does its own thing
with regard to refresher logic and which also, in the protocol, requires
implementations to keep state of which OI an LSA is received on (rather
than providing information in the LSA to allow it to be looked up - as
other LSAs requiring such assocation were careful to do).
* ospf_lsa.h: (struct ospf_interface) Add back the pointer to oi, but only
for type-9 now.
* ospf_nsm.c: (ospf_db_summary_add) check the oi actually exists first -
doesn't obviate the need for opaque to ensure oi pointers get cleaned up
when ospf_interfaces disappear.
* ospf_opaque.{c,h}: (ospf_opaque_functab,ospf_opaque_lsa_refresh) Refresher
LSA functions now need to return the LSA to the general refresh logic,
to indicate whether the LSA was refreshed.
* ospf_lsa.h: (struct ospf_lsa) remove oi pointer
* ospf_lsa.c: (ospf_network_lsa_refresh) instead of keeping a pointer, just
lookup the oi when it's needed. This decouples network LSA from oi lifetime
and avoids having to invalidate pointers in LSAs when an oi changes,
simplifying the code.
2006-05-30 Paul Jakma <paul.jakma@sun.com>
* (general) Fix confusion around MaxAge-ing and problem with
high-latency networks. Analysis and suggested fixes by
Phillip Spagnolo, in [quagga-dev 4132], on which this commit
expands slightly.
* ospf_flood.{c,h}: (ospf_lsa_flush) new function.
Scope-general form of existing flush functions, essentially
the dormant ospf_maxage_flood() but without the ambiguity of
whether it is responsible for flooding.
* ospf_lsa.c: (ospf_lsa_maxage) Role minimised to simply setup
LSA on the Maxage list and schedule removal - no more.
ospf_lsa_flush* being the primary way to kick-off flushes
of LSAs.
Don't hardcode the remover-timer value, which was too
short for very high-latency networks.
(ospf_maxage_lsa_remover) Just do what needs to be done to
remove maxage LSAs from the maxage list, remove the call
to ospf_flood_through().
Don't hardcode remove-timer value.
(ospf_lsa_{install,flush_schedule}) ospf_lsa_flush is the correct
entrypoint to flushing maxaged LSAs.
(lsa_header_set) Use a define for the initial age, useful for
testing.
* ospf_opaque.c: (ospf_opaque_lsa_refresh) ditto.
(ospf_opaque_lsa_flush_schedule) ditto.
* ospfd.h: ({struct ospf,ospf_new}) Add maxage_delay parameter,
interval to wait before running the maxage_remover. Supply a
suitable default.
Add a define for OSPF_LSA_INITIAL_AGE, see lsa_header_set().
* (general) Get rid of the router and network LSA specific refresh timers
and make the general refresher do this instead. Get rid of the twiddling
of timers for router/network LSA that was spread across the code.
This lays the foundations for future, general LSA refresh improvements,
such as making sequence rollover work, and having generic LSA delays.
* ospfd.h: (struct ospf) Bye bye to the router-lsa update timer thread
pointer.
(struct ospf_area) and to the router-lsa refresh timer.
* ospf_interface.h: Remove the network_lsa_self timer thread pointer
* ospf_lsa.h: (struct ospf_lsa) oi field should always be there, for benefit
of type-2/network LSA processing.
(ospf_{router,network}_lsa_{update_timer,timer_add}) no timers for these
more
(ospf_{router,network}_lsa_update) more generic functions to indicate that some
router/network LSAs need updating
(ospf_router_lsa_update_area) update router lsa in a particular area alone.
(ospf_{summary,summary_asbr,network}_lsa_refresh) replaced by the general
ospf_lsa_refresh function.
(ospf_lsa_refresh) general LSA refresh function
* ospf_interface.h: (struct ospf_if_params) add field for saved network LSA
seqnum
* ospf_interfa.c: (ospf_new_if_params) init network_lsa_seqnum field to
initial seqnum - doesnt matter though.
* ospf_lsa.c: (ospf_network_lsa_new) check for any saved sequence number,
and use if it exists. Save the result back. This should help avoid needless
round of LSUpdate/LSRequests when a neighbour has to tell the originator
"uhm, i have something newer than that already".
* ospf_vty.c: (show_ip_ospf_interface_sub) Show the saved network LSA seqnum
* It's possible for the packet output buffer to be filled up with a long
series of non-Hello packets in between Hellos packets, such that the
router's neighbours don't receive the Hello packet in time, even though
the hello-timer ran at about the right time. Fix this by prioritising
Hello packets, letting them skip the queue and go ahead of any packets
already on the queue.
This problem can occur when there are lots of LSAs and slow links.
* ospf_packet.h: (ospf_hello_send_sub) not used outside of ospf_packet.c
* ospf_packet.c: (ospf_fifo_push_head) add packet to head of fifo (so its
no longer really a fifo, but hey)
(ospf_packet_add_top) add packet to top of the packet output queue.
(ospf_hello_send_sub) Put Hello's at the top of the packet output queue.
make it take in_addr_t parameter, so that this
ospf_hello_send can re-use this code too.
(ospf_hello_send) consolidate code by using ospf_hello_send_sub
(ospf_poll_send,ospf_hello_reply_timer) adjust for ospf_hello_send_sub.
* The hello protocol monitors connectivity in 2 different ways:
a) local -> remote
b) remote -> local
Connectivity is required in both directions (2-way) for adjacencies to
form.
The first requires a round-trip to detect, and is done by advertising
which other hosts a router knows about in its hello messages. This allows
a host to detect which other routers are and are not receiving its
message. If a remote neighbour delists the local router, then the local
router raises a "1-Way Received" event.
The latter is straight-forward, and is detected by setting a timer for the
neighbour. If another Hello packet is not received within this time then
the neighbour is dead, and a separate "Inactive" event is raised.
These are 2 different and relatively independent measures.
Knowing that we can optimise the 2nd, remote->local measure and reset
the timer when /any/ packet arrives from that neighbour. For any packet
is as good as a Hello packet. This can help in marginal situations, where
the number of protocol messages that must be sent sometimes can exceed
the capacity of the network to transmit the messages within the configured
dead-time. I.e. an OSPF network with lots of LSAs, slow links and/or
slow hosts (e.g. O(10k) LSAs, O(100kbit) links, embedded CPUs, and O(10s)
dead-times).
This optimisation allows an OSPF network to run closer to this margin,
and/or allows networks to perhaps better cope with rare periods of
exceptional load, where otherwise they would not.
It's fully compatible with plain OSPF implementations and doesn't
prejudice dead-neighbour detection.
* ospf_nsm.h: Rename HelloReceived event to PacketReceived.
* ospf_nsm.c: (nsm_hello_received) -> nsm_packet_received
* ospf_packet.c: Schedule PacketReceived whenever a valid message is
received.
* ospf_ase.c: (ospf_ase_calculate_route) Fix compiler warning about eval
needing brackets.
(various) add defensive asserts.
* ospf_lsdb.c: (ospf_lsdb_add) add missing node unlock if same lsa already
was indexed.
(ospf_lsdb_delete) check it's actually the same as specified lsa before
deleting
(ospf_lsdb_lookup_by_id_next) fix another corner case - no result =>
don't go on.
* ospf_interface.c: (ospf_if_{new,cleanup}) don't touch the network_lsa_self,
ISM and NSM take care of cleaning it up if needs be + we want to keep
network_lsa_self around when possible for the the seqnum.
This shouldn't really make much difference though, particularly as we have
a separate sequence number memory mechanism.
* ospf_packet.c: (ospf_ls_upd) the corresponding test on the arrival side
in (ospf_flood) is <, so this should be >=, not >, purely for consistency.
There is no practical effect here though.
* ospf_zebra.c: (ospf_distribute_list_update_timer) forces a
refresh of default route each time it finds a default prefix.
This is suboptimal, just record that it needs to be done and
do it once.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
* ospf_zebra.c: (ospf_distribute_list_update_timer)
If there are updates to the distribute list every 5 second or less,
ospf_distribute_list_update_timer() will never run as the timer gets
rearmed for each update. This fixes it by never rearming an active
distribute list timer.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Roman Hoog Antink <rha@open.ch> reports:
When adding a connected route (using vtysh, without restart) to the
redistribution access list of ospfd, while static routes already exist,
the update timer ospf_distribute_list_update_timer() is being run for
static routes only. That way, the connected route never appears in the
OSPF database, until quagga is completely restarted.
The update timer for connected routes is cancelled in
ospfd/ospfd_zebra.c:ospf_distribute_list_update():976, were a new timer
is scheduled for static routes, caused by the loop in ospf_filter_update().
* ospf_zebra.c: (ospf_distribute_list_update_timer) make it
refresh all external routes. This fixes the problem
reported by Roman.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
* ospf_lsdb.c: (lsdb_prefix_set) memset is unneeded, as all fields are
initialised explicitly, and this function can be in the top-3 of a
profile when there are a lot of LSAs.
This code is only used one place and can be made local.
Gcc is smart enough to inline local functions if it wants to.
The function also has a big chunk of compatiablity code that
is no longer used; since quagga is now in a version control system
the source does not need to be used as a historical reference.
The following syntax forms were not historically supported
by Quagga, although IOS accepted them w/o a problem:
no ip ospf cost <1-65535>
no ospf cost <1-65535>
no ip ospf cost <1-65535> A.B.C.D
no ospf cost <1-65535> A.B.C.D
From now on Quagga also supports these variants.
* ospf_zebra.c: (ospf_distribute_check_connected) check to make filter out
routes matching connected routes was matching against OSPF networks, which
can be far more general than the actual connected interfaces. Fix.
Doing redistribute delete with full BGP table was taking
30 minutes, this drops it down to less than a second.
* ospf_lsa.c: (ospf_lsa_maxage) When flushing lots of entries the
performance is terrible because it looks up each LSA entry through
ospf_lsa_maxage_exist before deleting causing O(N^2) performance. Use a
new OSPF_LSA_MAXAGE flag instead of scan - and maintain it.
(ospf_lsa_maxage_exist) removed
(ospf_lsa_maxage_delete) maintain OSPF_LSA_MAXAGE flag
In some cases ospfd does not recalc the route table. This
happens when ospfd receives an old LSA which will trigger
recalc but the this recalc will fail because all interfaces
isn't up yet. Next LSA that is originated matches the old one
so no recalc will be performed. This problem has been observed
when there are only 2 ppp I/Fs in an area, both go down at the
same time, then they come up again with a few seconds apart.
* ospf_lsa.c: (ospf_{router,network}_lsa_install) avoid a needless scheduling
of SPF.
(ospf_lsa_different) fix bug in LSA comparison that would lead to the
described failure to schedule SPF.
* ospf_packet.c: make this message conditional on 'debug ospf event', as it
be easily triggered with, e.g., multiple subnets sharing same physical
network. E.g, see bug #532.
* ospf_lsa.c: (link_info_set) Use %zd for size_t - C99 is old enough now.
Lots of similar warnings all over the code.
(ospf_lsa_translated_nssa_compare) Unused func - delete.
* global: In struct ospf_path, change struct ospf_interface *oi to int
ifindex. It is unsafe to reference *oi as an ospf interface can be
deleted under your feet. Use a weak reference instead.
* ospf_spf.c: (ospf_get_next_link) One must check the vertex type, Router or
Network, to select type link to match against. Link type 1 has neighbour
router ID in link_id and link type 2 has IP address of DR. Since router
id may have same value as an existing IP address one risks matching a
router ID against a DR.
This function will return the interface for the first matching
remote address for PtP i/f's. That won't work for multiple
unnumbered i/f's as these may all have the same address.
Pass in the struct interface pointer, ifp, to find the
correct set of oi's to search in. This also reduces the
size of the search list, making it faster.
* ospfd/ospf_interface.c: Add struct interface * param to
ospf_if_lookup_recv_if() to select the right list to search in.
* ospfd/ospf_interface.h: ditto.
* ospfd/ospf_packet.c: Pass new ifp argument to ospf_if_lookup_recv_if()
Makes it possible to run OSPF on multiple PtP interfaces
with the same remote address.
* ospfd/ospf_interface.c: Export ospf_if_table_lookup().
* ospfd/ospf_interface.h: ditto.
* ospfd/ospfd.c: (ospf_network_run_interface) Use ospf_if_table_lookup() to
determine whether OSPF is already configured for a subnet and interface.
Should a self originated Network/Router LSA with higher
LS seq. nr. be received we should flood and install it in
the LSDB but we cannot use it for our internal calculations
as it is stale.
Reorginate an new LSA to replace the stale one as soon
as possible.
ospf_lsa_install() will calculate LSA checksum so no
need to do it before calling ospf_lsa_install().
Set the OSPF_LSA_SELF_CHECKED flag on own LSA's to
save ospf_lsa_is_self_originated() some work.
Do not memset() memory that is about to overwritten
with memcpy().
This piece of code causes all Quagga routers on a broadcast link to
send a HELLO packet simultaneously if they see a new neighbor. It also
resets the HELLO timer, so all the quagga routers will continue to
send HELLO packets simultaneously in the future. This is not good
(especially on networks with a lot of Quagga routers connected), and
is explicitly discouraged by the OSPF standard, RFC 2328 (chapter
4.4.Timers).
I suggest to remove the code snippet, it does not provide much benefit
anyway.
Should probably have AC_TYPE_UINT16_T in configure.ac to make it really
clean... and a fresh import of gnulib, the existing copy of gnulib seems to
be manually put some stuff in zebra.h. I'm leaving that alone for now,
since a fresh import will probably clean up a lot of cruft and it would be a
duplicated effort to fix some things now.
The FreeBSD port 0.99.11_1 files/patch-ospfd-ospfd.h can probably go away
after this is applied.
* ospfd/ospfd.c: (opsf_if_update) Check if ospf_lookup() returns NULL.
Fixes bug introduced with recent ospf_network_run changes in
a49eb30a, where SEGV will happen if not the "router ospf" command has
been executed before the first interfaces are reported by zebra.
Signed-off-by: Paul Jakma <paul@quagga.net>
* ospf_spf.c: (ospf_spf_process_stubs) Track whether
parent router vertex is the root, so that the host-route
suppression logic need only be activated for such vertices.
Move the actual logic to ospf_intra_add_stub.
* ospf_route.c: (ospf_intra_add_stub) Main test of link moved
here, notionally more appropriate.
Add an struct interface paramenter and adjust the affected
code accordingly.
The old code was a mess looping over all interfaces several times
when one interface was added/changed.
* ospfd/ospfd.h: Add struct interface parameter to ospf_if_update()
* ospfd/ospf_zebra.c: Add ifp arg to ospf_if_update() calls.
(ospf_interface_address_delete) delete ospf_if_update() call,
redundant as function calls ospf_if_free() itself.
* ospfd/ospfd.c: (ospf_network_unset) handle deconfiguration here,
rather than ospf_if_update.
(ospf_network_run_interface) ospf_network_run, for
any given interface.
(ospf_network_run) move guts to previous, and use it.
(ospf_if_update) Adjust to take struct interface as argument, as
all callers have a specific ifp in mind.
Iterate over ifp's connected list and call ospf_network_run_interface
instead of ospf_network_run, turning this path into O(nm) rather
than O(n^2).
Adjust all code dealing with opsf_if_update and ospf_network_run to
pass the new struct interface * arg.
(some minor modifications and bug-additions by Paul Jakma).
Signed-off-by: Paul Jakma <paul@quagga.net>
Update ospf_db_desc_send(), ospf_ls_upd_queue_send() and ospf_ls_req_send()
to always use OSPF_ALLSPFROUTERS for PtP links.
See RFC 2328, chap 8.1 for details:
"The IP destination address for the packet is selected as
follows. On physical point-to-point networks, the IP
destination is always set to the address AllSPFRouters."
Without this, it won't be possible to establish adjacencies on
multiple unnumbered links to the same router.
ChangeLog:
2008-07-25 Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
* ospfd/ospf_packet.c: Set destination for PtP links to
OSPF_ALLSPFROUTERS.
2008-08-15 Paul Jakma <paul.jakma@sun.com>
* */*: Fix various problems flagged by Sun Studio compiler.
- '<qualifier> <storage>' obsolescent in declarations
- empty statements (';' after ALIAS definitions)
- implicit declarations (e.g printstack in lib/log.c)
- "\%" in printf string instead of "%%"
- loops that return on the first iteration (legitimately, but
compiler can't really know), e.g. bgp_routemap.c
- internal declarations which mask prototypes.
2008-08-14 Stephen Hemminger <stephen.hemminger@vyatta.com>
* lib/log.{c,h}: struct message argument should point to const
* */*.c: adjust to suit,
Signed-off-by: Paul Jakma <paul@quagga.net>
2008-08-13 Daniel Ng <daniel_ng11@lycos.com>
* ospf_nsm.c: (nsm_change_state) Refresh default route on
state change - a hack, but it works.
Signed-off-by: Paul Jakma <paul@quagga.net>
2008-08-13 Jingjing Duan <Jingjing.Duan@sun.com>
* ospfd/: Remove the old checksum implementation and
use the consolidated version.
* isisd/: ditto, thus fixing isisd checksuming on big-endian.
Signed-off-by: Paul Jakma <paul@quagga.net>
2008-01-30 Peter Szilagyi <sp615@hszk.bme.hu>
* lib/stream.h: Remove named 'new' parameter in prototype
for c++ header compatibility.
* ospfd/ospf_opaque.h: ditto
* ospfd/ospfd.h: Renamed struct export to _export for c++
header compatibility.
* ospf6d/ospf6_area.h: ditto
2007-08-07 Atis Elsts <atis@mikrotik.com>
* ospf_spf.c: (ospf_spf_next) Sort heap in correct direction
after vertex cost is changed, thus fixing incorrect SPF
calculation on certain topologies.
* lib/pqueue.{c,h}: Export trickle_up
2007-05-09 Paul Jakma <paul.jakma@sun.com>
* configure.ac: sys/conf.h depends on sys/param.h, at least on
FBSD 6.2.
(bug #363) Should check for in_pktinfo for IRDP
2006-05-27 Paul Jakma <paul.jakma@sun.com>
* configure.ac: General cleanup of header and type checks, introducing
an internal define, QUAGGA_INCLUDES, to build up a list of
stuff to include so as to avoid 'present but cant be compiled'
warnings.
Misc additional checks of things missing according to autoscan.
Add LIBM, for bgpd's use of libm, so as to avoid burdening
LIBS, and all the binaries, with libm linkage.
Remove the bad practice of using m4 changequote(), just
quote the []'s in the case statements properly.
This should fix bugs 162, 303 and 178.
* */*.{c,h}: Update all HAVE_* to the standard autoconf namespaced
HAVE_* defines. I.e. HAVE_SA_LEN -> HAVE_STRUCT_SOCKADDR_SA_LEN,
* bgpd/Makefile.am: Add LIBM to bgpd's LDADD, for pow().
2007-05-07 Paul Jakma <paul.jakma@sun.com>
* ospf_spf.c: (ospf_vertex_new) Dont init vertices to infinity,
just let 0 be a special case.
(ospf_spf_add_parent) 0 distance candidate vertex is special,
cost still to be initialised - asserting that new distance
is <= existing only makes sense where w already has a cost.
(ospf_spf_next) Infinite cost links should not be followed,
bar those of the root.
2007-04-30 Andrew J. Schorr <ajschorr@alumni.princeton.edu>
* ospfd/ospfd.c: (ospf_network_match_iface) Comment out
COMPATIBILITY_MODE. Going forward, the ospf "network" command
will use a simple test: does the network command prefix
contain the connected (destination) prefix of the interface?
* doc/ospfd.texi: Add a paragraph to the description of the OSPFv2
network command to explain how we handle interfaces with
peer addresses.
2007-04-21 Andrew J. Schorr <ajschorr@alumni.princeton.edu>
* ospf_interface.c: (ospf_if_set_multicast) Fix bug: was testing
interface passive status improperly in light of the recent
'passive-interface default' patch. Now need to test
OSPF_IF_PASSIVE_STATUS(oi) instead of
OSPF_IF_PARAM(oi, passive_interface).
2007-03-23 Paul Jakma <paul.jakma@sun.com>
* ospf_spf.c: (ospf_nexthop_calculation) Fix silly regression
causing ospfd to fail to calculate paths past networks not
attached to root vertex, introduced with bug #330 fixes.
2007-03-14 Andrew J. Schorr <ajschorr@alumni.princeton.edu>
* ospf_snmp.c: (ospf_snmp_neighbor_state) New function to
map internal quagga neighbor states to SNMP standard values.
(ospfNbrEntry) Call new ospf_snmp_neighbor_state function.
2007-03-14 Andrew J. Schorr <ajschorr@alumni.princeton.edu>
* ospf_zebra.c: (ospf_zebra_add, ospf_zebra_delete) Fix bug
where inet_ntoa was used twice in the same debug message,
which doesn't work because there's a single shared buffer
for the returned string. The fix is to use inet_ntop.
2007-02-27 Andrew J. Schorr <ajschorr@alumni.princeton.edu>
* ospfd.c: (ospf_terminate) Exit immediately if ospf is not
actually running (e.g. the config file was empty). Fixes
bug where SIGTERM would not kill ospfd.
2007-02-26 Paul Jakma <paul.jakma@sun.com>
* ospf_spf.c: Fix regression introduced with bug #330 fix: The
cost update added to ospf_spf_add_parent only handled PtP
case, differing from same functionality in higher-level
ospf_spf_next. Regression diagnosed by Anders Pedersen,
mailnews+router-quagga-dev@news.cohaesio.com.
(ospf_vertex_new) Initialise vertices to max-cost.
(ospf_spf_init) Root vertex always creates with 0 cost.
(ospf_spf_add_parent) Remove the buggy V->W cost calculating
code, instead take the new distance as a parameter.
(ospf_nexthop_calculation) Take distance as parameter, so it
can be passed down to add_parent.
(ospf_spf_next) Dont initialise candiate vertex distance,
vertex_new does so already. Pass distance down to
nexthop_calculation (see above).
2007-01-24 Paul Jakma <paul.jakma@sun.com>
* ospf_spf.c: Bug #330: Nexthop calculation sometimes may fail,
and it needs to indicate this result to SPF.
(ospf_spf_add_parent) Flush of parent list needs to be done here,
for simplicity.
(ospf_nexthop_calculation) Caller needs to know whether
nexthop calculation succeeded. Every return statement must
correctly indicate such.
(ospf_spf_next) Queueing/prioritisation of vertices in SPF
must take into account whether nexthop_calculation succeeded,
or SPF may fail to find best paths.
2006-12-12 Andrew J. Schorr <ajschorr@alumni.princeton.edu>
* if.h: (struct connected) Add new ZEBRA_IFA_PEER flag indicating
whether a peer address has been configured. Comment now shows
the new interpretation of the destination addr: if ZEBRA_IFA_PEER
is set, then it must contain the destination address, otherwise
it may contain the broadcast address or be NULL.
(CONNECTED_DEST_HOST,CONNECTED_POINTOPOINT_HOST) Remove obsolete
macros that were specific to IPv4 and not fully general.
(CONNECTED_PEER) New macro to check ZEBRA_IFA_PEER flag.
(CONNECTED_PREFIX) New macro giving the prefix to insert into
the RIB: if CONNECTED_PEER, then use the destination (peer) address,
else use the address field.
(CONNECTED_ID) New macro to come up with an identifying address
for the struct connected.
* if.c: (if_lookup_address, connected_lookup_address) Streamline
logic with new CONNECTED_PREFIX macro.
* prefix.h: (PREFIX_COPY_IPV4, PREFIX_COPY_IPV6) New macros
for better performance than the general prefix_copy function.
* zclient.c: (zebra_interface_address_read) For non-null destination
addresses, set prefixlen to equal the address prefixlen. This
is needed to get the new CONNECTED_PREFIX macro to work properly.
* connected.c: (connected_up_ipv4, connected_down_ipv4,
connected_up_ipv6, connected_down_ipv6) Simplify logic using the
new CONNECTED_PREFIX macro.
(connected_add_ipv4) Set prefixlen in destination addresses (required
by the CONNECTED_PREFIX macro). Use CONNECTED_PEER macro instead
of testing for IFF_POINTOPOINT. Delete invalid warning message.
Warn about cases where the ZEBRA_IFA_PEER is set but no
destination address has been supplied (and turn off the flag).
(connected_add_ipv6) Add new flags argument so callers may set
the ZEBRA_IFA_PEER flag. If peer/broadcast address satisfies
IN6_IS_ADDR_UNSPECIFIED, then reject it with a warning.
Set prefixlen in destination address so CONNECTED_PREFIX will work.
* connected.h: (connected_add_ipv6) Add new flags argument so
callers may set the ZEBRA_IFA_PEER flag.
* interface.c: (connected_dump_vty) Use CONNECTED_PEER macro
to decide whether the destination address is a peer or broadcast
address (instead of checking IFF_BROADCAST and IFF_POINTOPOINT).
* if_ioctl.c: (if_getaddrs) Instead of setting a peer address
only when the IFF_POINTOPOINT is set, we now accept a peer
address whenever it is available and not the same as the local
address. Otherwise (no peer address assigned), we check
for a broadcast address (regardless of the IFF_BROADCAST flag).
And must now pass a flags value of ZEBRA_IFA_PEER to
connected_add_ipv4 when a peer address is assigned.
The same new logic is used with the IPv6 code as well (and we
pass the new flags argument to connected_add_ipv6).
(if_get_addr) Do not bother to check IFF_POINTOPOINT: just
issue the SIOCGIFDSTADDR ioctl and see if we get back
a peer address not matching the local address (and set
the ZEBRA_IFA_PEER in that case). If there's no peer address,
try to grab SIOCGIFBRDADDR regardless of whether IFF_BROADCAST is set.
* if_ioctl_solaris.c: (if_get_addr) Just try the SIOCGLIFDSTADDR ioctl
without bothering to check the IFF_POINTOPOINT flag. And if
no peer address was found, just try the SIOCGLIFBRDADDR ioctl
without checking the IFF_BROADCAST flag. Call connected_add_ipv4
and connected_add_ipv6 with appropriate flags.
* if_proc.c: (ifaddr_proc_ipv6) Must pass new flags argument to
connected_add_ipv6.
* kernel_socket.c: (ifam_read) Must pass new flags argument to
connected_add_ipv6.
* rt_netlink.c: (netlink_interface_addr) Copy logic from iproute2
to determine local and possible peer address (so there's no longer
a test for IFF_POINTOPOINT). Set ZEBRA_IFA_PEER flag appropriately.
Pass new flags argument to connected_add_ipv6.
(netlink_address) Test !CONNECTED_PEER instead of if_is_broadcast
to determine whether the connected destination address is a
broadcast address.
* bgp_nexthop.c: (bgp_connected_add, bgp_connected_delete)
Simplify logic by using new CONNECTED_PREFIX macro.
* ospf_interface.c: (ospf_if_is_configured, ospf_if_lookup_by_prefix,
ospf_if_lookup_recv_if) Simplify logic using new CONNECTED_PREFIX
macro.
* ospf_lsa.c: (lsa_link_ptop_set) Using the new CONNECTED_PREFIX
macro, both options collapse into the same code.
* ospf_snmp.c: (ospf_snmp_if_update) Simplify logic using new
CONNECTED_ID macro.
(ospf_snmp_is_if_have_addr) Simplify logic using new CONNECTED_PREFIX
macro.
* ospf_vty.c: (show_ip_ospf_interface_sub) Use new CONNECTED_PEER macro
instead of testing the IFF_POINTOPOINT flag.
* ospfd.c: (ospf_network_match_iface) Use new CONNECTED_PEER macro
instead of testing with if_is_pointopoint. And add commented-out
code to implement alternative (in my opinion) more elegant behavior
that has no special-case treatment for PtP addresses.
(ospf_network_run) Use new CONNECTED_ID macro to simplify logic.
* rip_interface.c: (rip_interface_multicast_set) Use new CONNECTED_ID
macro to simplify logic.
(rip_request_interface_send) Fix minor bug: ipv4_broadcast_addr does
not give a useful result if prefixlen is 32 (we require a peer
address in such cases).
* ripd.c: (rip_update_interface) Fix same bug as above.
2006-12-04 Andrew J. Schorr <ajschorr@alumni.princeton.edu>
* ospfd.c: (ospf_network_run) Remove an offending 'break' statement.
Previously, after creating a single ospf_interface on a given
network interface, the code would skip to the next interface
without considering other connected addresses on the interface.
After removing the 'break', we now consider all connected addresses.
2006-11-30 Andrew J. Schorr <ajschorr@alumni.princeton.edu>
* ospf_zebra.c: (ospf_router_id_update_zebra,
ospf_interface_address_add, ospf_interface_address_delete)
If (IS_DEBUG_OSPF (zebra, ZEBRA_INTERFACE)) is enabled, then
add a debug message about what Zebra is telling us.
(ospf_zebra_add_discard) Add a debug message matching the one
already in ospf_zebra_delete_discard.
2006-11-28 Andrew J. Schorr <ajschorr@alumni.princeton.edu>
* ospf_vty.c: (ospf_passive_interface_default) Take additional
'newval' arg so we can update ospf->passive_interface_default inside
this function. More importantly, we now call ospf_if_set_multicast
on all ospf_interfaces.
(ospf_passive_interface, no_ospf_passive_interface) Fix bug:
for 'default' case, argv[0] is undefined, so we must test for
(argc == 0) before using argv[0]. And since
ospf_passive_interface_default now calls ospf_if_set_multicast as
needed, we can just return after calling
ospf_passive_interface_default.
2006-10-24 Andrew J. Schorr <ajschorr@alumni.princeton.edu>
* ospf_zebra.c: (ospf_redistribute_default_set) Fix bug where
a new value for ospf->default_originate was being ignored
if a previous 'default-information originate' command
had already been processed.
2006-10-22 Yar Tikhiy <yar@comp.chem.msu.su>
* (general) Add support for passive-interface default (with
minor edits by Paul Jakma).
* ospf_interface.h: Add OSPF_IF_PASSIVE_STATUS macro, looking
at configured value, or the global 'default' value, as
required.
* ospf_interface.c: (ospf_if_new_hook) Leave passive
unconfigured per default, allowing global 'default' to
take effect for unconfigured interfaces.
* ospf_packet.c: (various) use OSPF_IF_PASSIVE_STATUS
* ospf_vty.c: (ospf_passive_interface_default) new function,
unset passive from all interfaces if default is enabled, as
the per-iface settings become redundant.
(ospf_passive_interface_update) new func, update passive
setting taking global default into account.
({no,}ospf_passive_interface_addr_cmd) Add support for
'default' variant of command.
(show_ip_ospf_interface_sub) Update to take global
default into account when printing passive status.
(ospf_config_write) ditto.
* ospfd.c: (ospf_new) set global passive-interface default.
* ospfd.h: (struct ospf) Add field for global
passive-interface.
2006-10-04 Oliver Hookins <ohookins@gmail.com>
* bgpd/bgp_main.c: Add configuration check option, with
'-C' rather than '-c' for consistency between daemons.
* isisd/isis_main.c: ditto
* ospf6d/ospf6_main.c: ditto
* ospfd/ospf_main.c: ditto
* ripngd/ripng_main.c: ditto
* vtysh/vtysh_main.c: ditto
* ripd/rip_main.c: Change the config check option to
'-C' and tidy up the code.
* zebra/main.c: ditto
2006-10-04 Stergiakis Alexandros <astergiakis@antcor.com>
* ripd/rip_main.c: This trivial patch introduces a new
command-line option '-c', which instructs zebra/ripd
to check its configuration file for validity, print
any error message, and then exit. This is useful when
the configuration file is edited by hand or otherwise,
and you simply want to validate it without any other
effect.
* zebra/main.c: ditto
2006-09-25 Andrew J. Schorr <ajschorr@alumni.princeton.edu>
* ospf_packet.c: (ospf_packet_dup, ospf_make_md5_digest)
Fix zlog_warn messages to eliminate compiler warnings.
(ospf_hello) Improve warning messages to show why we
are complaining.
2006-08-28 Andy Gay <andy@andynet.net>
* ospf_packet.c: (ospf_make_db_desc) Assert added with More-bit
fixes does not hold up with addition of Ogier DB-Exchange
optimisation, which can empty the db-summary list in between
sent DD packets. Remove assert, update More-bit always when
in Exchange.
2006-08-27 J.J. Krabbendam <jkrabbendam@aimsys.nl>
* ospfd.c: (ospf_finish_final) default redistribute should be
unset too, fixes bug where reconfiguring ospfd completely
can no longer enable default redistribution.
