Use MSI interrupts with fallback to INTx interrupts.
Signed-off-by: Martin Jocic <martin.jocic@kvaser.com>
Link: https://lore.kernel.org/all/20240620181320.235465-3-martin.jocic@kvaser.com
[mkl: kvaser_pciefd_probe(): call pci_free_irq_vectors() unconditionally]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
A new interrupt is triggered by resetting the DMA RX buffers.
Since MSI interrupts are faster than legacy interrupts, the reset
of the DMA buffers must be moved to the very end of the ISR,
otherwise a new MSI interrupt will be masked by the current one.
Signed-off-by: Martin Jocic <martin.jocic@kvaser.com>
Link: https://lore.kernel.org/all/20240620181320.235465-2-martin.jocic@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Replace the variable name err used for return codes with the more
generic name ret. An upcoming patch series for adding MSI interrupts
will introduce code which also returns values other than return codes.
Renaming the variable to ret enables using it for both purposes.
This is applied to the whole file to make it consistent.
Signed-off-by: Martin Jocic <martin.jocic@kvaser.com>
Link: https://lore.kernel.org/all/20240614151524.2718287-8-martin.jocic@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Rename the variable name board_irq in the ISR to pci_irq to
be more specific and to match the macro by which it is read.
Signed-off-by: Martin Jocic <martin.jocic@kvaser.com>
Link: https://lore.kernel.org/all/20240614151524.2718287-7-martin.jocic@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Make the short function kvaser_pciefd_set_tx_irq inline. This function
is effectively three lines long and therefore inlining it should be
OK according to rule #15 of the Linux kernel coding style.
Signed-off-by: Martin Jocic <martin.jocic@kvaser.com>
Link: https://lore.kernel.org/all/20240614151524.2718287-5-martin.jocic@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This check is already done at the creation of the net devices in
kvaser_pciefd_setup_can_ctrls called from kvaser_pciefd_probe.
If it fails, the driver won't load, so there should be no need to
repeat the check inside the ISR. The number of channels is read
from the FPGA and should be trusted.
Signed-off-by: Martin Jocic <martin.jocic@kvaser.com>
Link: https://lore.kernel.org/all/20240614151524.2718287-3-martin.jocic@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
'mscan_state' is unused since the original
commit afa17a500a ("net/can: add driver for mscan family &
mpc52xx_mscan").
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/all/20240525232509.191735-1-linux@treblig.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Xilinx CAN driver supports AXI CAN, AXI CANFD, CANPS and CANFD PS IPs.
Document all supported IPs in comment description.
Signed-off-by: Harini T <harini.t@amd.com>
Link: https://lore.kernel.org/all/20240503060553.8520-3-harini.t@amd.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Commit cfcb4465e9 ("can: slcan: remove legacy infrastructure")
removed the 10-device limit. Update the Kconfig help text accordingly.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Acked-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/all/20240427152648.25434-1-mans@mansr.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This driver is including the legacy GPIO header <linux/gpio.h>
but the only thing it is using from that header is the wrong
define for GPIOF_DIR_OUT.
Fix it up by using GPIO_LINE_DIRECTION_* macros respectively.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/all/20240412173332.186685-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Simon reported that ndo_change_mtu() methods were never
updated to use WRITE_ONCE(dev->mtu, new_mtu) as hinted
in commit 501a90c945 ("inet: protect against too small
mtu values.")
We read dev->mtu without holding RTNL in many places,
with READ_ONCE() annotations.
It is time to take care of ndo_change_mtu() methods
to use corresponding WRITE_ONCE()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Simon Horman <horms@kernel.org>
Closes: https://lore.kernel.org/netdev/20240505144608.GB67882@kernel.org/
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Acked-by: Shannon Nelson <shannon.nelson@amd.com>
Link: https://lore.kernel.org/r/20240506102812.3025432-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In a future patch HAS_IOPORT=n will disable inb()/outb() and friends at
compile time. We thus need to add HAS_IOPORT as dependency for
those drivers requiring them. For the DEFXX driver the use of I/O
ports is optional and we only need to fence specific code paths. It also
turns out that with HAS_IOPORT handled explicitly HAMRADIO does not need
the !S390 dependency and successfully builds the bpqether driver.
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Maciej W. Rozycki <macro@orcam.me.uk>
Co-developed-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since Xilinx-based adapters now support up to eight CAN channels, the
TX interrupt mask array must have eight elements.
Signed-off-by: Martin Jocic <martin.jocic@kvaser.com>
Link: https://lore.kernel.org/all/2ab3c0585c3baba272ede0487182a423a420134b.camel@kvaser.com
Fixes: 9b221ba452 ("can: kvaser_pciefd: Add support for Kvaser PCIe 8xCAN")
[mkl: replace Link by Fixes tag]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Since 3f9c26210c ("can: error: add definitions for the different CAN
error thresholds") we have proper defines for the various CAN error
thresholds. So make use of it and replace 256 by
CAN_BUS_OFF_THRESHOLD.
Link: https://lore.kernel.org/all/20240304074503.3584662-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The structure gs_device_mode dm::mode is a __le32, use cpu_to_le32()
to assign GS_CAN_MODE_RESET.
As GS_CAN_MODE_RESET is 0x0, this is basically a no-op.
Link: https://lore.kernel.org/all/20240304074540.3584842-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
We want to be able to run rtnl_fill_ifinfo() under RCU protection
instead of RTNL in the future.
This patch prepares dev_get_iflink() and nla_put_iflink()
to run either with RTNL or RCU held.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEUEC6huC2BN0pvD5fKDiiPnotvG8FAmXUZiITHG1rbEBwZW5n
dXRyb25peC5kZQAKCRAoOKI+ei28b8KLB/9MKkUjbbBh9nXezyWdXnulj5jpHWlJ
Xa7Sz7e+Gw5HbpK1/RF3Mb3/uf5D+DTMa2jjUJhezGCugW6ugoFapDC1bJxdafIN
pAZQG/7EYi4TqHEO3/aS5sMh3pISs29COnmHHdQCYfyTMZPKGcDkJuwa7POhHhR1
zrjavD0N2ihBfhoadlT+GQ9QYu+JyWnjrB27hSznsktW9Jeju1u6F9nvOXn60aZU
e7QXgsKe94YXLEed3hj7buPAIirY+tLKIpbw7TtJJwk6EBnnK17S+2wydR0N7yWK
SSsaKJxZCiiaoYkl9chkKTyqh2I3qa/HsxUrFY3TGx5VMhWLiiH/r5eI
=pIjg
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-6.9-20240220' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2024-02-20
this is a pull request of 9 patches for net-next/master.
The first patch is by Francesco Dolcini and removes a redundant check
for pm_clock_support from the m_can driver.
Martin Hundebøll contributes 3 patches to the m_can/tcan4x5x driver to
allow resume upon RX of a CAN frame.
3 patches by Srinivas Goud add support for ECC statistics to the
xilinx_can driver.
The last 2 patches are by Oliver Hartkopp and me, target the CAN RAW
protocol and fix an error in the getsockopt() for CAN-XL introduced in
the previous pull request to net-next (linux-can-next-for-6.9-20240213).
linux-can-next-for-6.9-20240220
* tag 'linux-can-next-for-6.9-20240220' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next:
can: raw: raw_getsockopt(): reduce scope of err
can: raw: fix getsockopt() for new CAN_RAW_XL_VCID_OPTS
can: xilinx_can: Add ethtool stats interface for ECC errors
can: xilinx_can: Add ECC support
dt-bindings: can: xilinx_can: Add 'xlnx,has-ecc' optional property
can: tcan4x5x: support resuming from rx interrupt signal
can: m_can: allow keeping the transceiver running in suspend
dt-bindings: can: tcan4x5x: Document the wakeup-source flag
can: m_can: remove redundant check for pm_clock_support
====================
Link: https://lore.kernel.org/r/20240220085130.2936533-1-mkl@pengutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add ECC support for Xilinx CAN Controller, so this driver reports
1bit/2bit ECC errors for FIFO's based on ECC error interrupt. ECC
feature for Xilinx CAN Controller selected through 'xlnx,has-ecc' DT
property
Signed-off-by: Srinivas Goud <srinivas.goud@amd.com>
Link: https://lore.kernel.org/all/20240213-xilinx_ecc-v8-2-8d75f8b80771@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The TDCO calculation was done using the currently applied data bittiming,
instead of the newly computed data bittiming, which means that the TDCO
had an invalid value unless setting the same data bittiming twice.
Fixes: d99755f71a ("can: netlink: add interface for CAN-FD Transmitter Delay Compensation (TDC)")
Signed-off-by: Maxime Jayat <maxime.jayat@mobile-devices.fr>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/all/40579c18-63c0-43a4-8d4c-f3a6c1c0b417@munic.io
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Implement the "wakeup-source" device tree property, so the chip is left
running when suspending, and its rx interrupt is used as a wakeup source
to resume operation.
Signed-off-by: Martin Hundebøll <martin@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add a flag to the device class structure that leaves the chip in a
running state with rx interrupt enabled, so that an m_can device driver
can configure and use the interrupt as a wakeup source.
Signed-off-by: Martin Hundebøll <martin@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
m_can_clk_start() already skip starting the clock when
clock support is disabled, remove the redundant check in
m_can_class_register().
This also solves the imbalance with m_can_clk_stop() that is called
afterward in the same function before the return.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://lore.kernel.org/all/20240104235723.46931-1-francesco@dolcini.it
[mkl: rebased to net-next/main]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In this case dev cannot be NULL, so remove redundant check.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 03fd3cf5a1 ("can: add driver for Softing card")
Signed-off-by: Daniil Dulov <d.dulov@aladdin.ru>
Link: https://lore.kernel.org/all/20240211150535.3529-1-d.dulov@aladdin.ru
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
m_can supports submitting multiple transmits with one register write.
This is an interesting option to reduce the number of SPI transfers for
peripheral chips.
The m_can_tx_op is extended with a bool that signals if it is the last
transmission and the submit should be executed immediately.
The worker then writes the skb to the FIFO and submits it only if the
submit bool is set. If it isn't set, the worker will write the next skb
which is waiting in the workqueue to the FIFO, etc.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://lore.kernel.org/all/20240207093220.2681425-15-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The network queue is currently always stopped in start_xmit and
continued in the interrupt handler. This is not possible anymore if we
want to keep multiple transmits in flight in parallel.
Use the previously introduced tx_fifo_in_flight counter to control the
network queue instead. This has the benefit of not needing to ask the
hardware about fifo status.
This patch stops the network queue in start_xmit if the number of
transmits in flight reaches the size of the fifo and wakes up the queue
from the interrupt handler once the transmits in flight drops below the
fifo size. This means any skbs over the limit will be rejected
immediately in start_xmit (it shouldn't be possible at all to reach that
state anyways).
The maximum number of transmits in flight is the size of the fifo.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://lore.kernel.org/all/20240207093220.2681425-13-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Keep track of the number of transmits in flight.
This patch prepares the driver to control the network interface queue
based on this counter. By itself this counter be
implemented with an atomic, but as we need to do other things in the
critical sections later I am using a spinlock instead.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://lore.kernel.org/all/20240207093220.2681425-12-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The current implementation uses the workqueue for peripheral chips to
submit work. Only a single work item is queued and used at any time.
To be able to keep more than one transmit in flight at a time, prepare
the workqueue to support multiple transmits at the same time.
Each work item now has a separate storage for a skb and a pointer to
cdev. This assures that each workitem can be processed individually.
The workqueue is replaced by an ordered workqueue which makes sure that
only a single worker processes the items queued on the workqueue. Also
items are ordered by the order they were enqueued. This removes most of
the concurrency the workqueue normally offers. It is not necessary for
this driver.
The cleanup functions have to be adopted a bit to handle this new
mechanism.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://lore.kernel.org/all/20240207093220.2681425-11-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
m_can_tx_handler is the only place where data is written to the tx fifo.
We can calculate the putidx in the driver code here to avoid the
dependency on the txfqs register.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/all/20240207093220.2681425-10-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
putidx is not an integer normally, it is an unsigned field used in
hardware registers. Use a u32 for it.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/all/20240207093220.2681425-9-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add TX support to get/set functions for ethtool coalescing.
tx-frames-irq and tx-usecs-irq can only be set/unset together.
tx-frames-irq needs to be less than TXE and TXB.
As rx and tx share the same timer, rx-usecs-irq and tx-usecs-irq can be
enabled/disabled individually but they need to have the same value if
enabled.
Polling is excluded from TX irq coalescing.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/all/20240207093220.2681425-8-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add the possibility to set coalescing parameters with ethtool.
rx-frames-irq and rx-usecs-irq can only be set and unset together as the
implemented mechanism would not work otherwise. rx-frames-irq can't be
greater than the RX FIFO size.
Also all values can only be changed if the chip is not active.
Polling is excluded from irq coalescing support.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/all/20240207093220.2681425-7-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Extend the coalescing implementation for transmits.
In normal mode the chip raises an interrupt for every finished transmit.
This implementation switches to coalescing mode as soon as an interrupt
handled a transmit. For coalescing the watermark level interrupt is used
to interrupt exactly after x frames were sent. It switches back into
normal mode once there was an interrupt with no finished transmit and
the timer being inactive.
The timer is shared with receive coalescing. The time for receive and
transmit coalescing timers have to be the same for that to work. The
benefit is to have only a single running timer.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/all/20240207093220.2681425-6-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
m_can offers the possibility to set an interrupt on reaching a watermark
level in the receive FIFO. This can be used to implement coalescing.
Unfortunately there is no hardware timeout available to trigger an
interrupt if only a few messages were received within a given time. To
solve this I am using a hrtimer to wake up the irq thread after x
microseconds.
The timer is always started if receive coalescing is enabled and new
received frames were available during an interrupt. The timer is stopped
if during a interrupt handling no new data was available.
If the timer is started the new item interrupt is disabled and the
watermark interrupt takes over. If the timer is not started again, the
new item interrupt is enabled again, notifying the handler about every
new item received.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://lore.kernel.org/all/20240207093220.2681425-5-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Combine header and data before writing to the transmit fifo to reduce
the overhead for peripheral chips.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/all/20240207093220.2681425-4-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The hrtimer_init() is called in m_can_plat_probe() and the hrtimer
function is set in m_can_class_register(). For readability it is better
to keep these two together in m_can_class_register().
Cc: Judith Mendez <jm@ti.com>
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/all/20240207093220.2681425-3-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Interrupts are enabled/disabled in more places than just m_can_start()
and m_can_stop(). Couple the polling timer with enabling/disabling of
all interrupts to achieve equivalent behavior.
Cc: Judith Mendez <jm@ti.com>
Fixes: b382380c0d ("can: m_can: Add hrtimer to generate software interrupt")
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/all/20240207093220.2681425-2-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds support for the PCI based PCIe/402 CAN interface family
from esd GmbH that is available with various form factors
(https://esd.eu/en/products/402-series-can-interfaces).
All boards utilize a FPGA based CAN controller solution developed
by esd (esdACC). For more information on the esdACC see
https://esd.eu/en/products/esdacc.
This driver detects all available CAN interface board variants of
the family but atm. operates the CAN-FD capable devices in
Classic-CAN mode only! A later patch will introduce the CAN-FD
functionality in this driver.
Co-developed-by: Thomas Körper <thomas.koerper@esd.eu>
Signed-off-by: Thomas Körper <thomas.koerper@esd.eu>
Signed-off-by: Stefan Mätje <stefan.maetje@esd.eu>
Link: https://lore.kernel.org/all/20231122160211.2110448-3-stefan.maetje@esd.eu
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Use preferred device_get_match_data() instead of of_match_device() to
get the driver match data. With this, adjust the includes to explicitly
include the correct headers.
Error checking for matching and match data was not necessary as matching
is always successful if we're already in probe and the match tables always
have data pointers.
Signed-off-by: Rob Herring <robh@kernel.org>
There is usbdrv_wrap in struct usb_driver and usb_device_driver, it
contains device_driver and for_devices. for_devices is used to
distinguish between device drivers and interface drivers.
Like the is_usb_device(), it tests the type of the device. We can test
that if the probe of device_driver is equal to usb_probe_device in
is_usb_device_driver(), and then the struct usbdrv_wrap is no longer
needed.
Clean up struct usbdrv_wrap, use device_driver directly in struct
usb_driver and usb_device_driver. This makes the code cleaner.
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20240104032822.1896596-1-yajun.deng@linux.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cross-merge networking fixes after downstream PR.
No conflicts.
Adjacent changes:
kernel/bpf/verifier.c
829955981c ("bpf: Fix verifier log for async callback return values")
a923819fb2 ("bpf: Treat first argument as return value for bpf_throw")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now that napi_schedule return a bool, we can drop napi_reschedule that
does the same exact function. The function comes from a very old commit
bfe13f54f5 ("ibm_emac: Convert to use napi_struct independent of struct
net_device") and the purpose is actually deprecated in favour of
different logic.
Convert every user of napi_reschedule to napi_schedule.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> # ath10k
Acked-by: Nick Child <nnac123@linux.ibm.com> # ibm
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for can/dev/rx-offload.c
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20231009133754.9834-3-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
IMX93 A0 chip involve the internal q-channel handshake in LPCG and
CCM to automatically handle the Flex-CAN IPG STOP signal. Only after
FLEX-CAN enter stop mode then can support the self-wakeup feature.
But meet issue when do the continue system PM stress test. When config
the CAN as wakeup source, the first time after system suspend, any data
on CAN bus can wakeup the system, this is as expect. But the second time
when system suspend, data on CAN bus can't wakeup the system. If continue
this test, we find in odd time system enter suspend, CAN can wakeup the
system, but in even number system enter suspend, CAN can't wakeup the
system. IC find a bug in the auto stop mode logic, and can't fix it easily.
So for the new imx93 A1, IC drop the auto stop mode and involve the
GPR to support stop mode (used before). IC define a bit in GPR which can
trigger the IPG STOP signal to Flex-CAN, let it go into stop mode.
And NXP claim to drop IMX93 A0, and only support IMX93 A1. So this patch
remove the auto stop mode, and add flag FLEXCAN_QUIRK_SETUP_STOP_MODE_GPR
to imx93.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://lore.kernel.org/all/20230726112458.3524165-2-haibo.chen@nxp.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Upstream commit 717c6ec241 ("can: sja1000: Prevent overrun stalls with
a soft reset on Renesas SoCs") fixes an issue with Renesas own SJA1000
CAN controller reception: the Rx buffer is only 5 messages long, so when
the bus loaded (eg. a message every 50us), overrun may easily
happen. Upon an overrun situation, due to a possible internal crosstalk
situation, the controller enters a frozen state which only can be
unlocked with a soft reset (experimentally). The solution was to offload
a call to sja1000_start() in a threaded handler. This needs to happen in
process context as this operation requires to sleep. sja1000_start()
basically enters "reset mode", performs a proper software reset and
returns back into "normal mode".
Since this fix was introduced, we no longer observe any stalls in
reception. However it was sporadically observed that the transmit path
would now freeze. Further investigation blamed the fix mentioned above,
and especially the reset operation. Reproducing the reset in a loop
helped identifying what could possibly go wrong. The sja1000 is a single
Tx queue device, which leverages the netdev helpers to process one Tx
message at a time. The logic is: the queue is stopped, the message sent
to the transceiver, once properly transmitted the controller sets a
status bit which triggers an interrupt, in the interrupt handler the
transmission status is checked and the queue woken up. Unfortunately, if
an overrun happens, we might perform the soft reset precisely between
the transmission of the buffer to the transceiver and the advent of the
transmission status bit. We would then stop the transmission operation
without re-enabling the queue, leading to all further transmissions to
be ignored.
The reset interrupt can only happen while the device is "open", and
after a reset we anyway want to resume normal operations, no matter if a
packet to transmit got dropped in the process, so we shall wake up the
queue. Restarting the device and waking-up the queue is exactly what
sja1000_set_mode(CAN_MODE_START) does. In order to be consistent about
the queue state, we must acquire a lock both in the reset handler and in
the transmit path to ensure serialization of both operations. It turns
out, a lock is already held when entering the transmit path, so we can
just acquire/release it as well with the regular net helpers inside the
threaded interrupt handler and this way we should be safe. As the
reset handler might still be called after the transmission of a frame to
the transceiver but before it actually gets transmitted, we must ensure
we don't leak the skb, so we free it (the behavior is consistent, no
matter if there was an skb on the stack or not).
Fixes: 717c6ec241 ("can: sja1000: Prevent overrun stalls with a soft reset on Renesas SoCs")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/all/20231002160206.190953-1-miquel.raynal@bootlin.com
[mkl: fixed call to can_free_echo_skb()]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The current at91_can driver uses NAPI to handle RX'ed CAN frames, the
RX IRQ is disabled and a NAPI poll is scheduled. Then in
at91_poll_rx() the RX'ed CAN frames are tried to read in order from
the device.
This approach has 2 drawbacks:
- Under high system load it might take too long from the initial RX
IRQ to the NAPI poll function to run. This causes RX buffer
overflows.
- The algorithm to read the CAN frames in order is not bullet proof
and may fail under certain use cases/system loads.
The rx-offload helper fixes these problems by reading the RX'ed CAN
frames in the interrupt handler and adding it to a list sorted by RX
timestamp. This list of RX'ed SKBs is then passed to the networking
stack via NAPI.
Convert the RX path to rx-offload, pass all CAN error frames with
can_rx_offload_queue_timestamp().
Link: https://lore.kernel.org/all/20231005-at91_can-rx_offload-v2-27-9987d53600e0@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This is a preparation patch to convert the driver to make use of the
rx-offload helper. With rx-offload the received CAN frames are sorted
by their timestamp. Regular CAN RX'ed and TX'ed CAN frames are
timestamped by the hardware. Error events are not.
Introduce a new function at91_alloc_can_err_skb() the allocates an
error SKB and reads the current timestamp from the controller.
Link: https://lore.kernel.org/all/20231005-at91_can-rx_offload-v2-26-9987d53600e0@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Since 3e5c291c79 ("can: add CAN_ERR_CNT flag to notify availability
of error counter") there is a dedicated flag to inform the user space,
that there are CAN error counters in the CAN error frame.
In case the device is not in bus off mode, send the error counters to
user space and set CAN_ERR_CNT.
Link: https://lore.kernel.org/all/20231005-at91_can-rx_offload-v2-25-9987d53600e0@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The driver implements a hand crafted CAN state handling. Update the
driver to make use of can_change_state(), introduced in ("can: dev:
Consolidate and unify state change handling")
Also switch from hand crafted CAN bus off handling to can_bus_off():
In case of a bus off, abort all pending TX requests, switch off the
device and let can_bus_off() handle the device restart.
Link: https://lore.kernel.org/all/20231005-at91_can-rx_offload-v2-24-9987d53600e0@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The at91 CAN controller automatically recovers from bus-off after 128
occurrences of 11 consecutive recessive bits.
After an auto-recovered bus-off, the error counters no longer reflect
this fact. On the sam9263 the state bits in the SR register show the
current state (based on the current error counters), while on sam9x5
and newer SoCs these bits are latched.
Take any latched bus-off information from the SR register into account
when calculating the CAN new state, to start the standard CAN bus off
handling.
Link: https://lore.kernel.org/all/20231005-at91_can-rx_offload-v2-23-9987d53600e0@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
On the sam9263 the SR bits for bus off, error passive, warning limit,
and error active are not latched and reflect the current status of the
controller. On the sam9x5 and newer SoCs these bits are latched.
To simplify the code, use can_state_get_by_berr_counter() to get the
state of the controller regardless of the SoC version.
Link: https://lore.kernel.org/all/20231005-at91_can-rx_offload-v2-22-9987d53600e0@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This is a preparation patch to convert the driver to the rx-offload
helper. In rx-offload RX, TX-done and CAN error handling are done in
the IRQ handler, SKB are pushed to the network stack in the NAPI poll
function.
Move the CAN frame error handling from the NAPI function at91_poll()
to the IRQ handler at91_poll(). To reflect this change, rename
at91_poll_err() to at91_irq_err_frame().
Link: https://lore.kernel.org/all/20231005-at91_can-rx_offload-v2-19-9987d53600e0@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
at91_poll_err() allocates a can error SKB, to inform the user space
about the CAN error. Then it fills the SKB with information the error
information and increases the net device error stats.
In case no SBK can be allocated (e.g. due to an OOM) or the NAPI quota
is 0 the function is left early and no stats are updated. This is not
helpful to the user, as there is no information about the faulty CAN
bus.
Increase the error stats even if no quota is left or no SKB can be
allocated.
While there treat No-Acknowledgment as a bus error, too.
Link: https://lore.kernel.org/all/20231005-at91_can-rx_offload-v2-18-9987d53600e0@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In at91_chip_start() first all IRQs are disabled, they do not have to
be disabled again at the end of the function before the requested IRQs
are enabled.
Remove the 2nd disable of all IRQs at the end of the function.
Link: https://lore.kernel.org/all/20231005-at91_can-rx_offload-v2-14-9987d53600e0@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Some CAN controllers do not have a register that contains the current
CAN state, but only a register that contains the error counters.
Introduce a new function can_state_get_by_berr_counter() that returns
the current TX and RX state depending on the provided CAN bit error
counters.
Link: https://lore.kernel.org/all/20231005-at91_can-rx_offload-v2-1-9987d53600e0@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
If the "struct can_priv::echoo_skb" is accessed out of bounds, this
would cause a kernel crash. Instead, issue a meaningful warning
message and return with an error.
Fixes: a6e4bc5304 ("can: make the number of echo skb's configurable")
Link: https://lore.kernel.org/all/20231005-can-dev-fix-can-restart-v2-5-91b5c1fd922c@pengutronix.de
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Move the debug message "restarted" and the CAN restart stats_after_
the successful restart of the CAN device, because the restart may
fail.
While there update the error message from printing the error number to
printing symbolic error names.
Link: https://lore.kernel.org/all/20231005-can-dev-fix-can-restart-v2-4-91b5c1fd922c@pengutronix.de
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
[mkl: mention stats in subject and description, too]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This race condition was discovered while updating the at91_can driver
to use can_bus_off(). The following scenario describes how the
converted at91_can driver would behave.
When a CAN device goes into BUS-OFF state, the driver usually
stops/resets the CAN device and calls can_bus_off().
This function sets the netif carrier to off, and (if configured by
user space) schedules a delayed work that calls can_restart() to
restart the CAN device.
The can_restart() function first checks if the carrier is off and
triggers an error message if the carrier is OK.
Then it calls the driver's do_set_mode() function to restart the
device, then it sets the netif carrier to on. There is a race window
between these two calls.
The at91 CAN controller (observed on the sama5d3, a single core 32 bit
ARM CPU) has a hardware limitation. If the device goes into bus-off
while sending a CAN frame, there is no way to abort the sending of
this frame. After the controller is enabled again, another attempt is
made to send it.
If the bus is still faulty, the device immediately goes back to the
bus-off state. The driver calls can_bus_off(), the netif carrier is
switched off and another can_restart is scheduled. This occurs within
the race window before the original can_restart() handler marks the
netif carrier as OK. This would cause the 2nd can_restart() to be
called with an OK netif carrier, resulting in an error message.
The flow of the 1st can_restart() looks like this:
can_restart()
// bail out if netif_carrier is OK
netif_carrier_ok(dev)
priv->do_set_mode(dev, CAN_MODE_START)
// enable CAN controller
// sama5d3 restarts sending old message
// CAN devices goes into BUS_OFF, triggers IRQ
// IRQ handler start
at91_irq()
at91_irq_err_line()
can_bus_off()
netif_carrier_off()
schedule_delayed_work()
// IRQ handler end
netif_carrier_on()
The 2nd can_restart() will be called with an OK netif carrier and the
error message will be printed.
To close the race window, first set the netif carrier to on, then
restart the controller. In case the restart fails with an error code,
roll back the netif carrier to off.
Fixes: 39549eef35 ("can: CAN Network device driver and Netlink interface")
Link: https://lore.kernel.org/all/20231005-can-dev-fix-can-restart-v2-2-91b5c1fd922c@pengutronix.de
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
During testing, I triggered a can_restart() with the netif carrier
being OK [1]. The BUG_ON, which checks if the carrier is OK, results
in a fatal kernel crash. This is neither helpful for debugging nor for
a production system.
[1] The root cause is a race condition in can_restart() which will be
fixed in the next patch.
Do not crash the kernel, issue an error message instead, and continue
restarting the CAN device anyway.
Fixes: 39549eef35 ("can: CAN Network device driver and Netlink interface")
Link: https://lore.kernel.org/all/20231005-can-dev-fix-can-restart-v2-1-91b5c1fd922c@pengutronix.de
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Fix below checkpatch warning:
WARNING: Missing a blank line after declarations
#2233: FILE: drivers/net/can/usb/etas_es58x/es58x_core.c:2233:
+ int ret = es58x_init_netdev(es58x_dev, ch_idx);
+ if (ret) {
Fixes: d8f26fd689 ("can: etas_es58x: remove es58x_get_product_info()")
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/all/20230924110914.183898-3-mailhol.vincent@wanadoo.fr
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Following [1], es58x_devlink.c now triggers the following
format-truncation GCC warnings:
drivers/net/can/usb/etas_es58x/es58x_devlink.c: In function ‘es58x_devlink_info_get’:
drivers/net/can/usb/etas_es58x/es58x_devlink.c:201:41: warning: ‘%02u’ directive output may be truncated writing between 2 and 3 bytes into a region of size between 1 and 3 [-Wformat-truncation=]
201 | snprintf(buf, sizeof(buf), "%02u.%02u.%02u",
| ^~~~
drivers/net/can/usb/etas_es58x/es58x_devlink.c:201:30: note: directive argument in the range [0, 255]
201 | snprintf(buf, sizeof(buf), "%02u.%02u.%02u",
| ^~~~~~~~~~~~~~~~
drivers/net/can/usb/etas_es58x/es58x_devlink.c:201:3: note: ‘snprintf’ output between 9 and 12 bytes into a destination of size 9
201 | snprintf(buf, sizeof(buf), "%02u.%02u.%02u",
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
202 | fw_ver->major, fw_ver->minor, fw_ver->revision);
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/can/usb/etas_es58x/es58x_devlink.c:211:41: warning: ‘%02u’ directive output may be truncated writing between 2 and 3 bytes into a region of size between 1 and 3 [-Wformat-truncation=]
211 | snprintf(buf, sizeof(buf), "%02u.%02u.%02u",
| ^~~~
drivers/net/can/usb/etas_es58x/es58x_devlink.c:211:30: note: directive argument in the range [0, 255]
211 | snprintf(buf, sizeof(buf), "%02u.%02u.%02u",
| ^~~~~~~~~~~~~~~~
drivers/net/can/usb/etas_es58x/es58x_devlink.c:211:3: note: ‘snprintf’ output between 9 and 12 bytes into a destination of size 9
211 | snprintf(buf, sizeof(buf), "%02u.%02u.%02u",
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
212 | bl_ver->major, bl_ver->minor, bl_ver->revision);
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/can/usb/etas_es58x/es58x_devlink.c:221:38: warning: ‘%03u’ directive output may be truncated writing between 3 and 5 bytes into a region of size between 2 and 4 [-Wformat-truncation=]
221 | snprintf(buf, sizeof(buf), "%c%03u/%03u",
| ^~~~
drivers/net/can/usb/etas_es58x/es58x_devlink.c:221:30: note: directive argument in the range [0, 65535]
221 | snprintf(buf, sizeof(buf), "%c%03u/%03u",
| ^~~~~~~~~~~~~
drivers/net/can/usb/etas_es58x/es58x_devlink.c:221:3: note: ‘snprintf’ output between 9 and 13 bytes into a destination of size 9
221 | snprintf(buf, sizeof(buf), "%c%03u/%03u",
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
222 | hw_rev->letter, hw_rev->major, hw_rev->minor);
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
This is not an actual bug because the sscanf() parsing makes sure that
the u8 are only two digits long and the u16 only three digits long.
Thus below declaration:
char buf[max(sizeof("xx.xx.xx"), sizeof("axxx/xxx"))];
allocates just what is needed to represent either of the versions.
This warning was known but ignored because, at the time of writing,
-Wformat-truncation was not present in the kernel, not even at W=3 [2].
One way to silence this warning is to check the range of all sub
version numbers are valid: [0, 99] for u8 and range [0, 999] for u16.
The module already has a logic which considers that when all the sub
version numbers are zero, the version number is not set. Note that not
having access to the device specification, this was an arbitrary
decision. This logic can thus be removed in favor of global check that
would cover both cases:
- the version number is not set (parsing failed)
- the version number is not valid (paranoiac check to please gcc)
Before starting to parse the product info string, set the version
sub-numbers to the maximum unsigned integer thus violating the
definitions of struct es58x_sw_version or struct es58x_hw_revision.
Then, rework the es58x_sw_version_is_set() and
es58x_hw_revision_is_set() functions: remove the check that the
sub-numbers are non zero and replace it by a check that they fit in
the expected number of digits. This done, rename the functions to
reflect the change and rewrite the documentation. While doing so, also
add a description of the return value.
Finally, the previous version only checked that
&es58x_hw_revision.letter was not the null character. Replace this
check by an alphanumeric character check to make sure that we never
return a special character or a non-printable one and update the
documentation of struct es58x_hw_revision accordingly.
All those extra checks are paranoid but have the merit to silence the
newly introduced W=1 format-truncation warning [1].
[1] commit 6d4ab2e97d ("extrawarn: enable format and stringop overflow warnings in W=1")
Link: https://git.kernel.org/torvalds/c/6d4ab2e97dcf
[2] https://lore.kernel.org/all/CAMZ6Rq+K+6gbaZ35SOJcR9qQaTJ7KR0jW=XoDKFkobjhj8CHhw@mail.gmail.com/
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Closes: https://lore.kernel.org/linux-can/20230914-carrousel-wrecker-720a08e173e9-mkl@pengutronix.de/
Fixes: 9f06631c3f ("can: etas_es58x: export product information through devlink_ops::info_get()")
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/all/20230924110914.183898-2-mailhol.vincent@wanadoo.fr
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
There is likely a copy-paste error here, as the exact same comment
appears below in this function, one time calling set_reset_mode(), the
other set_normal_mode().
Fixes: 429da1cc84 ("can: Driver for the SJA1000 CAN controller")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/all/20230922155130.592187-1-miquel.raynal@bootlin.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Here is the big set of tty and serial driver changes for 6.6-rc1.
Lots of cleanups in here this cycle, and some driver updates. Short
summary is:
- Jiri's continued work to make the tty code and apis be a bit more
sane with regards to modern kernel coding style and types
- cpm_uart driver updates
- n_gsm updates and fixes
- meson driver updates
- sc16is7xx driver updates
- 8250 driver updates for different hardware types
- qcom-geni driver fixes
- tegra serial driver change
- stm32 driver updates
- synclink_gt driver cleanups
- tty structure size reduction
All of these have been in linux-next this week with no reported issues.
The last bit of cleanups from Jiri and the tty structure size reduction
came in last week, a bit late but as they were just style changes and
size reductions, I figured they should get into this merge cycle so that
others can work on top of them with no merge conflicts.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZPH+jA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykKyACgldt6QeenTN+6dXIHS/eQHtTKZwMAn3arSeXI
QrUUnLFjOWyoX87tbMBQ
=LVw0
-----END PGP SIGNATURE-----
Merge tag 'tty-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the big set of tty and serial driver changes for 6.6-rc1.
Lots of cleanups in here this cycle, and some driver updates. Short
summary is:
- Jiri's continued work to make the tty code and apis be a bit more
sane with regards to modern kernel coding style and types
- cpm_uart driver updates
- n_gsm updates and fixes
- meson driver updates
- sc16is7xx driver updates
- 8250 driver updates for different hardware types
- qcom-geni driver fixes
- tegra serial driver change
- stm32 driver updates
- synclink_gt driver cleanups
- tty structure size reduction
All of these have been in linux-next this week with no reported
issues. The last bit of cleanups from Jiri and the tty structure size
reduction came in last week, a bit late but as they were just style
changes and size reductions, I figured they should get into this merge
cycle so that others can work on top of them with no merge conflicts"
* tag 'tty-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (199 commits)
tty: shrink the size of struct tty_struct by 40 bytes
tty: n_tty: deduplicate copy code in n_tty_receive_buf_real_raw()
tty: n_tty: extract ECHO_OP processing to a separate function
tty: n_tty: unify counts to size_t
tty: n_tty: use u8 for chars and flags
tty: n_tty: simplify chars_in_buffer()
tty: n_tty: remove unsigned char casts from character constants
tty: n_tty: move newline handling to a separate function
tty: n_tty: move canon handling to a separate function
tty: n_tty: use MASK() for masking out size bits
tty: n_tty: make n_tty_data::num_overrun unsigned
tty: n_tty: use time_is_before_jiffies() in n_tty_receive_overrun()
tty: n_tty: use 'num' for writes' counts
tty: n_tty: use output character directly
tty: n_tty: make flow of n_tty_receive_buf_common() a bool
Revert "tty: serial: meson: Add a earlycon for the T7 SoC"
Documentation: devices.txt: Fix minors for ttyCPM*
Documentation: devices.txt: Remove ttySIOC*
Documentation: devices.txt: Remove ttyIOC*
serial: 8250_bcm7271: improve bcm7271 8250 port
...
veth and vxcan need to make sure the ifindexes of the peer
are not negative, core does not validate this.
Using iproute2 with user-space-level checking removed:
Before:
# ./ip link add index 10 type veth peer index -1
# ip link show
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: enp1s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP mode DEFAULT group default qlen 1000
link/ether 52:54:00:74:b2:03 brd ff:ff:ff:ff:ff:ff
10: veth1@veth0: <BROADCAST,MULTICAST,M-DOWN> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 8a:90:ff:57:6d:5d brd ff:ff:ff:ff:ff:ff
-1: veth0@veth1: <BROADCAST,MULTICAST,M-DOWN> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether ae:ed:18:e6:fa:7f brd ff:ff:ff:ff:ff:ff
Now:
$ ./ip link add index 10 type veth peer index -1
Error: ifindex can't be negative.
This problem surfaced in net-next because an explicit WARN()
was added, the root cause is older.
Fixes: e6f8f1a739 ("veth: Allow to create peer link with given ifindex")
Fixes: a8f820a380 ("can: add Virtual CAN Tunnel driver (vxcan)")
Reported-by: syzbot+5ba06978f34abb058571@syzkaller.appspotmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes all those 'char's an explicit 'u8'. This is part of the
continuing unification of chars and flags to be consistent u8.
This approaches tty_port_default_receive_buf().
Note that we do not change signedness as we compile with
-funsigned-char.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: William Hubbs <w.d.hubbs@gmail.com>
Cc: Chris Brannon <chris@the-brannons.com>
Cc: Kirk Reiser <kirk@reisers.ca>
Cc: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Max Staudt <max@enpas.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Cc: Andreas Koensgen <ajk@comnets.uni-bremen.de>
Cc: Jeremy Kerr <jk@codeconstruct.com.au>
Cc: Matt Johnston <matt@codeconstruct.com.au>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230810091510.13006-18-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This makes all those 'unsigned char's an explicit 'u8'. This is part of
the continuing unification of chars and flags to be consistent u8.
This approaches tty_port_default_receive_buf(). Flags to be next.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: William Hubbs <w.d.hubbs@gmail.com>
Cc: Chris Brannon <chris@the-brannons.com>
Cc: Kirk Reiser <kirk@reisers.ca>
Cc: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Max Staudt <max@enpas.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Cc: Andreas Koensgen <ajk@comnets.uni-bremen.de>
Cc: Jeremy Kerr <jk@codeconstruct.com.au>
Cc: Matt Johnston <matt@codeconstruct.com.au>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230810091510.13006-17-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Count passed to tty_ldisc_ops::receive_buf*(), ::lookahead_buf(), and
returned from ::receive_buf2() is expected to be size_t. So set it to
size_t to unify with the rest of the code.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: William Hubbs <w.d.hubbs@gmail.com>
Cc: Chris Brannon <chris@the-brannons.com>
Cc: Kirk Reiser <kirk@reisers.ca>
Cc: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Max Staudt <max@enpas.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Cc: Andreas Koensgen <ajk@comnets.uni-bremen.de>
Cc: Jeremy Kerr <jk@codeconstruct.com.au>
Cc: Matt Johnston <matt@codeconstruct.com.au>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230810091510.13006-16-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'count' is going to be unsigned and the 'count >= 0' test would be
always true then. Move the condition to the loop where this is easier to
check.
It looks as is easier to follow after all too.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: Max Staudt <max@enpas.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: linux-can@vger.kernel.org
Link: https://lore.kernel.org/r/20230810091510.13006-15-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Create a label with can327_uart_side_failure() and spin unlock. And jump
there from all three fail paths.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: Max Staudt <max@enpas.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: linux-can@vger.kernel.org
Link: https://lore.kernel.org/r/20230810091510.13006-14-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty->disc_data is 'void *', so there is no need to cast from that.
Therefore remove the casts and assign the pointer directly.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Cc: Max Staudt <max@enpas.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Cc: linux-can@vger.kernel.org
Cc: netdev@vger.kernel.org
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Max Staudt <max@enpas.org>
Link: https://lore.kernel.org/r/20230801062237.2687-2-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty->disc_data is 'void *', so there is no need to cast from that.
Therefore remove the casts and assign the pointer directly.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Cc: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: linux-can@vger.kernel.org
Cc: netdev@vger.kernel.org
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20230731080244.2698-6-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To be able to understand issues during probe easier, add error messages
if something fails.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://lore.kernel.org/all/20230728141923.162477-7-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
tcan4552 and tcan4553 do not have wake or state pins, so they are
currently not compatible with the generic driver. The generic driver
uses tcan4x5x_disable_state() and tcan4x5x_disable_wake() if the gpios
are not defined. These functions use register bits that are not
available in tcan4552/4553.
This patch adds support by introducing version information to reflect if
the chip has wake and state pins. Also the version is now checked.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://lore.kernel.org/all/20230728141923.162477-6-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The datasheet calls these registers ID1 and ID2. Rename these to avoid
confusion.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Link: https://lore.kernel.org/all/20230728141923.162477-5-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
To reduce debugging effort in case the mram is misconfigured, add this
size check of the DT configuration. Currently if the mram configuration
doesn't fit into the available MRAM it just overwrites other areas of
the MRAM.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Link: https://lore.kernel.org/all/20230728141923.162477-4-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The mentioned register is not writable. It is reserved and should not be
written.
Fixes: 39dbb21b6a ("can: tcan4x5x: Specify separate read/write ranges")
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Link: https://lore.kernel.org/all/20230728141923.162477-3-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
There is no possible for platform_get_irq() to return 0
and the return value of platform_get_irq() is more sensible
to show the error reason.
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Link: https://lore.kernel.org/all/20230731075252.359965-1-ruanjinjie@huawei.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Move PCI Vendor and Device ID of ASIX AX99100 PCIe to Multi I/O
Controller to pci_ids.h for its serial and parallel port driver
support in subsequent patches.
Signed-off-by: Jiaqing Zhao <jiaqing.zhao@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20230724083933.3173513-3-jiaqing.zhao@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PCI_SUBVENDOR_ID_ASIX is defined as 0xa000, which is not the vendor id
assigned to ASIX by PCI-SIG. Remove it to avoid possible confusion and
conflict.
Signed-off-by: Jiaqing Zhao <jiaqing.zhao@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20230724083933.3173513-2-jiaqing.zhao@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver used to pass received CAN frames/skbs to the network stack
with netif_rx(). In netif_rx() the skbs are queued to the local CPU.
If IRQs are handled in round robin, OoO packets may occur.
To avoid out-of-order reception convert the driver from netif_rx() to
NAPI.
For USB devices with timestamping support use the rx-offload helper
can_rx_offload_queue_timestamp() for the RX, and
can_rx_offload_get_echo_skb_queue_timestamp() for the TX path. Devices
without timestamping support use can_rx_offload_queue_tail() for RX,
and can_rx_offload_get_echo_skb_queue_tail() for the TX path.
Link: https://lore.kernel.org/all/559D628C.5020100@hartkopp.net
Link: https://github.com/candle-usb/candleLight_fw/issues/166
Link: https://lore.kernel.org/all/20230718-gs_usb-rx-offload-v2-3-716e542d14d5@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Rename the rx_offload_get_echo_skb() function to
can_rx_offload_get_echo_skb_queue_timestamp(), since it inserts the
echo skb into the rx-offload queue sorted by timestamp.
This is a preparation for adding
can_rx_offload_get_echo_skb_queue_tail(), which adds the echo skb to
the end of the queue. This is intended for devices that do not support
timestamps.
Link: https://lore.kernel.org/all/20230718-gs_usb-rx-offload-v2-1-716e542d14d5@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In gs_usb_disconnect(), all channels are destroyed first, then all
anchored RX URBs (parent->rx_submitted) are disposed with
usb_kill_anchored_urbs().
The call to usb_kill_anchored_urbs() is not needed, as
gs_destroy_candev() of the last active channel already disposes the RX
URBS.
Remove not needed call to usb_kill_anchored_urbs() from
gs_usb_disconnect().
Link: https://lore.kernel.org/all/20230718-gs_usb-cleanups-v1-11-c3b9154ec605@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In gs_destroy_candev(), the netdev is unregistered first, then all
anchored TX URBs (dev->tx_submitted) are disposed with
usb_kill_anchored_urbs().
The call to usb_kill_anchored_urbs() is not needed, as
unregister_candev() calls gs_can_close(), which already disposes the
TX URBS.
Remove not needed call to usb_kill_anchored_urbs() from
gs_destroy_candev().
Link: https://lore.kernel.org/all/20230718-gs_usb-cleanups-v1-10-c3b9154ec605@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When the USB device is unplugged, gs_can_close() (which implements the
struct net_device_ops::ndo_stop callback) is called. In this function
an attempt is made to shut down the USB device with a USB control
message. For disconnected devices this will fail and a warning message
is printed.
Silence the driver by removing the printout of the error message if
the reset command fails.
Link: https://lore.kernel.org/all/20230718-gs_usb-cleanups-v1-9-c3b9154ec605@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Remove unnecessary "out of memory" message from the error path of
gs_can_start_xmit() and gs_can_open().
Convert the printout in case of a failing usb_submit_urb() in
gs_can_open() from numbers to human readable error codes.
Link: https://lore.kernel.org/all/20230718-gs_usb-cleanups-v1-8-c3b9154ec605@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In case of an RX overflow error from the CAN controller and an OOM
where no skb can be allocated, the error counters are not incremented.
Fix this by first incrementing the error counters and then allocate
the skb.
Fixes: d08e973a77 ("can: gs_usb: Added support for the GS_USB CAN devices")
Link: https://lore.kernel.org/all/20230718-gs_usb-cleanups-v1-7-c3b9154ec605@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/all/20230724211841.805053-1-robh@kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The controllers present in the D1 are extremely similar to the R40
and require the same reset quirks, but An extra quirk is needed to support
receiving packets.
Signed-off-by: John Watts <contact@jookia.org>
Link: https://lore.kernel.org/all/20230721221552.1973203-6-contact@jookia.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The Allwinner D1's CAN controllers have the ACPC and ACPM registers
moved down. Compensate for this by adding an offset quirk for the
acceptance registers.
Signed-off-by: John Watts <contact@jookia.org>
Link: https://lore.kernel.org/all/20230721221552.1973203-5-contact@jookia.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Remove unused/legacy peak_usb_netif_rx() function (not longer used
since commit 28e0a70ced ("can: peak_usb: CANFD: store 64-bits hw
timestamps").
Signed-off-by: Peter Seiderer <ps.report@gmx.net>
Link: https://lore.kernel.org/all/20230721180758.26199-1-ps.report@gmx.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
After an initial link up the CAN device is in ERROR-ACTIVE mode. Due
to a missing CAN_STATE_STOPPED in gs_can_close() it doesn't change to
STOPPED after a link down:
| ip link set dev can0 up
| ip link set dev can0 down
| ip --details link show can0
| 13: can0: <NOARP,ECHO> mtu 16 qdisc pfifo_fast state DOWN mode DEFAULT group default qlen 10
| link/can promiscuity 0 allmulti 0 minmtu 0 maxmtu 0
| can state ERROR-ACTIVE restart-ms 1000
Add missing assignment of CAN_STATE_STOPPED in gs_can_close().
Cc: stable@vger.kernel.org
Fixes: d08e973a77 ("can: gs_usb: Added support for the GS_USB CAN devices")
Link: https://lore.kernel.org/all/20230718-gs_usb-fix-can-state-v1-1-f19738ae2c23@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEDs2BvajyNKlf9TJQvlAcSiqKBOgFAmS3jZATHG1rbEBwZW5n
dXRyb25peC5kZQAKCRC+UBxKKooE6Fo4CACVxU4+xMgAszot9Sup7psEiUjbOHKd
TCxEEm9GML/aquPbXxx3r0yztyAzd1dF9zXSFGofUyfVV/pdKbu7h1vP+/EndmiL
W9eoVhnYzAbz2TivFgqQwqqTlosEgKmZF5qGl4eloH6luOILbvrl/UuD0J70h3gK
Ixus6TyEIdI2y1ewTlWXMOriedTVeTX+DC2S02Bi42cVFdAm29nie2fCdHVGhF/o
a0KICO3HjKhTmGReSHDpCMro+r93BezmYxoM96K4a911tge7fLzYhQQ1+ZVyQ3Mw
DRHMD1ehM6cWd0GUce3LqBjb9zx9ciQK0ohqKzAIaEV+Rta84P/CHtbn
=GOLr
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-6.6-20230719' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2023-07-19
The first 2 patches are by Judith Mendez, target the m_can driver and
add hrtimer based polling support for TI AM62x SoCs, where the
interrupt of the MCU domain's m_can cores is not routed to the Cortex
A53 core.
A patch by Rob Herring converts the grcan driver to use the correct DT
include files.
Michal Simek and Srinivas Neeli add support for optional reset control
to the xilinx_can driver.
The next 2 patches are by Jimmy Assarsson and add support for new
Kvaser pciefd to the kvaser_pciefd driver.
Mao Zhu's patch for the ucan driver removes a repeated word from a
comment.
* tag 'linux-can-next-for-6.6-20230719' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next:
can: ucan: Remove repeated word
can: kvaser_pciefd: Add support for new Kvaser pciefd devices
can: kvaser_pciefd: Move hardware specific constants and functions into a driver_data struct
can: Explicitly include correct DT includes
can: xilinx_can: Add support for controller reset
dt-bindings: can: xilinx_can: Add reset description
can: m_can: Add hrtimer to generate software interrupt
dt-bindings: net: can: Remove interrupt properties for MCAN
====================
Link: https://lore.kernel.org/r/20230719072348.525039-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for new Kvaser pciefd devices, based on SmartFusion2 SoC.
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20230622151153.294844-3-extja@kvaser.com
[mkl: mark structs as static]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Move hardware specific address offsets, interrupt masks and DMA mapping
function, into struct kvaser_pciefd_driver_data, as a step towards adding
new devices based on different hardware.
Co-developed-by: Martin Jocic <majoc@kvaser.com>
Signed-off-by: Martin Jocic <majoc@kvaser.com>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20230622151153.294844-2-extja@kvaser.com
[mkl: mark structs as static]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add support for an optional reset for the CAN controller using the reset
driver. If the CAN node contains the "resets" property, then this logic
will perform CAN controller reset.
Signed-off-by: Srinivas Neeli <srinivas.neeli@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/all/ab7e6503aa3343e39ead03c1797e765be6c50de2.1689164442.git.michal.simek@amd.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/all/20230714174757.4060748-1-robh@kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The mcp251xfd controller needs an idle bus to enter 'Normal CAN 2.0
mode' or . The maximum length of a CAN frame is 736 bits (64 data
bytes, CAN-FD, EFF mode, worst case bit stuffing and interframe
spacing). For low bit rates like 10 kbit/s the arbitrarily chosen
MCP251XFD_POLL_TIMEOUT_US of 1 ms is too small.
Otherwise during polling for the CAN controller to enter 'Normal CAN
2.0 mode' the timeout limit is exceeded and the configuration fails
with:
| $ ip link set dev can1 up type can bitrate 10000
| [ 731.911072] mcp251xfd spi2.1 can1: Controller failed to enter mode CAN 2.0 Mode (6) and stays in Configuration Mode (4) (con=0x068b0760, osc=0x00000468).
| [ 731.927192] mcp251xfd spi2.1 can1: CRC read error at address 0x0e0c (length=4, data=00 00 00 00, CRC=0x0000) retrying.
| [ 731.938101] A link change request failed with some changes committed already. Interface can1 may have been left with an inconsistent configuration, please check.
| RTNETLINK answers: Connection timed out
Make MCP251XFD_POLL_TIMEOUT_US timeout calculation dynamic. Use
maximum of 1ms and bit time of 1 full 64 data bytes CAN-FD frame in
EFF mode, worst case bit stuffing and interframe spacing at the
current bit rate.
For easier backporting define the macro MCP251XFD_FRAME_LEN_MAX_BITS
that holds the max frame length in bits, which is 736. This can be
replaced by can_frame_bits(true, true, true, true, CANFD_MAX_DLEN) in
a cleanup patch later.
Fixes: 55e5b97f00 ("can: mcp25xxfd: add driver for Microchip MCP25xxFD SPI CAN")
Signed-off-by: Fedor Ross <fedor.ross@ifm.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/20230717-mcp251xfd-fix-increase-poll-timeout-v5-1-06600f34c684@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Introduce timer polling method to MCAN since some SoCs may not
have M_CAN interrupt routed to A53 Linux and do not have
interrupt property in device tree M_CAN node.
On AM62x SoC, MCANs on MCU domain do not have hardware interrupt
routed to A53 Linux, instead they will use timer polling method.
Add an hrtimer to MCAN class device. Each MCAN will have its own
hrtimer instantiated if there is no hardware interrupt found in
device tree M_CAN node. The timer will generate a software
interrupt every 1 ms. In hrtimer callback, we check if there is
a transaction pending by reading a register, then process by
calling the isr if there is.
Tested-by: Hiago De Franco <hiago.franco@toradex.com> # Toradex Verdin AM62
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Judith Mendez <jm@ti.com>
Link: https://lore.kernel.org/all/20230707204714.62964-3-jm@ti.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
If the gs_usb device driver is unloaded (or unbound) before the
interface is shut down, the USB stack first calls the struct
usb_driver::disconnect and then the struct net_device_ops::ndo_stop
callback.
In gs_usb_disconnect() all pending bulk URBs are killed, i.e. no more
RX'ed CAN frames are send from the USB device to the host. Later in
gs_can_close() a reset control message is send to each CAN channel to
remove the controller from the CAN bus. In this race window the USB
device can still receive CAN frames from the bus and internally queue
them to be send to the host.
At least in the current version of the candlelight firmware, the queue
of received CAN frames is not emptied during the reset command. After
loading (or binding) the gs_usb driver, new URBs are submitted during
the struct net_device_ops::ndo_open callback and the candlelight
firmware starts sending its already queued CAN frames to the host.
However, this scenario was not considered when implementing the
hardware timestamp function. The cycle counter/time counter
infrastructure is set up (gs_usb_timestamp_init()) after the USBs are
submitted, resulting in a NULL pointer dereference if
timecounter_cyc2time() (via the call chain:
gs_usb_receive_bulk_callback() -> gs_usb_set_timestamp() ->
gs_usb_skb_set_timestamp()) is called too early.
Move the gs_usb_timestamp_init() function before the URBs are
submitted to fix this problem.
For a comprehensive solution, we need to consider gs_usb devices with
more than 1 channel. The cycle counter/time counter infrastructure is
setup per channel, but the RX URBs are per device. Once gs_can_open()
of _a_ channel has been called, and URBs have been submitted, the
gs_usb_receive_bulk_callback() can be called for _all_ available
channels, even for channels that are not running, yet. As cycle
counter/time counter has not set up, this will again lead to a NULL
pointer dereference.
Convert the cycle counter/time counter from a "per channel" to a "per
device" functionality. Also set it up, before submitting any URBs to
the device.
Further in gs_usb_receive_bulk_callback(), don't process any URBs for
not started CAN channels, only resubmit the URB.
Fixes: 45dfa45f52 ("can: gs_usb: add RX and TX hardware timestamp support")
Closes: https://github.com/candle-usb/candleLight_fw/issues/137#issuecomment-1623532076
Cc: stable@vger.kernel.org
Cc: John Whittington <git@jbrengineering.co.uk>
Link: https://lore.kernel.org/all/20230716-gs_usb-fix-time-stamp-counter-v1-2-9017cefcd9d5@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The gs_usb driver handles USB devices with more than 1 CAN channel.
The RX path for all channels share the same bulk endpoint (the
transmitted bulk data encodes the channel number). These per-device
resources are allocated and submitted by the first opened channel.
During this allocation, the resources are either released immediately
in case of a failure or the URBs are anchored. All anchored URBs are
finally killed with gs_usb_disconnect().
Currently, gs_can_open() returns with an error if the allocation of a
URB or a buffer fails. However, if usb_submit_urb() fails, the driver
continues with the URBs submitted so far, even if no URBs were
successfully submitted.
Treat every error as fatal and free all allocated resources
immediately.
Switch to goto-style error handling, to prepare the driver for more
per-device resource allocation.
Cc: stable@vger.kernel.org
Cc: John Whittington <git@jbrengineering.co.uk>
Link: https://lore.kernel.org/all/20230716-gs_usb-fix-time-stamp-counter-v1-1-9017cefcd9d5@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Use the TX FIFO size read from CAN controller register, instead of using
hard coded value.
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/all/20230529134248.752036-15-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add support for the Classical CAN raw DLC functionality to send and receive
DLC values from 9 .. 15.
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/all/20230529134248.752036-13-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Replace opencoded masking and shifting, with GENMASK, FIELD_GET and
FIELD_PREP macros.
Suggested-by: Vincent MAILHOL <mailhol.vincent@wanadoo.fr>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/all/20230529134248.752036-12-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Sort the registers defines, in the same order as the register bits/fields
are defined.
Sort register bits/fields in MSB-to-LSB order.
Update and add comments.
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/all/20230529134248.752036-11-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Change return type to void for kvaser_pciefd_transmit_irq(),
kvaser_pciefd_receive_irq() and kvaser_pciefd_set_tx_irq().
These functions always return zero.
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/all/20230529134248.752036-10-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Rename device ID defines to better match the product name of the supported
device.
Use 16 bit hexadecimal values for device IDs.
And format kvaser_pciefd_id_table using clang-format.
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/all/20230529134248.752036-9-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Sort the includes in alphabetic order.
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/all/20230529134248.752036-8-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Remove SPI flash parameter read functionality, since it's only used for
reading the interface CAN controller count.
This information is already read from a register, making the information
redundant.
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/all/20230529134248.752036-7-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Define unsigned constants with type suffix 'U'
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/all/20230529134248.752036-6-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Set hardware timestamp on transmitted packets.
Fixes: 26ad340e58 ("can: kvaser_pciefd: Add driver for Kvaser PCIEcan devices")
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/all/20230529134248.752036-5-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add new function, kvaser_pciefd_set_skb_timestamp(), to set skb hwtstamps.
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/all/20230529134248.752036-4-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The Kvaser KCAN controller got a feature to send error frames on request.
The packet KVASER_PCIEFD_PACK_TYPE_EFRAME_ACK signals that the requested
error frame was transmitted.
Since this feature is not supported by the driver, drop the handler and add
KVASER_PCIEFD_PACK_TYPE_EFRAME_ACK to the list of unexpected packet types.
Fixes: 26ad340e58 ("can: kvaser_pciefd: Add driver for Kvaser PCIEcan devices")
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/all/20230529134248.752036-3-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The PCI interrupt register, KVASER_PCIEFD_IRQ_REG, is level triggered.
Writing to the register doesn't affect it.
Fixes: 26ad340e58 ("can: kvaser_pciefd: Add driver for Kvaser PCIEcan devices")
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/all/20230529134248.752036-2-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Introduce a method to calculate the exact size in bits of a CAN(-FD)
frame with or without dynamic bitstuffing.
These are all the possible combinations taken into account:
- Classical CAN or CAN-FD
- Standard or Extended frame format
- CAN-FD CRC17 or CRC21
- Include or not intermission
Instead of doing several individual macro definitions, declare the
can_frame_bits() function-like macro. To this extent, do a full
refactoring of the length definitions.
In addition add the can_frame_bytes(). This function-like macro
replaces the existing macro:
- CAN_FRAME_OVERHEAD_SFF: can_frame_bytes(false, false, 0)
- CAN_FRAME_OVERHEAD_EFF: can_frame_bytes(false, true, 0)
- CANFD_FRAME_OVERHEAD_SFF: can_frame_bytes(true, false, 0)
- CANFD_FRAME_OVERHEAD_EFF: can_frame_bytes(true, true, 0)
Function-like macros were chosen over inline functions because they
can be used to initialize const struct fields.
The different maximum frame lengths (maximum data length, including
intermission) are as follow:
Frame type bits bytes
-------------------------------------------------------
Classic CAN SFF no bitstuffing 111 14
Classic CAN EFF no bitstuffing 131 17
Classic CAN SFF bitstuffing 135 17
Classic CAN EFF bitstuffing 160 20
CAN-FD SFF no bitstuffing 579 73
CAN-FD EFF no bitstuffing 598 75
CAN-FD SFF bitstuffing 712 89
CAN-FD EFF bitstuffing 736 92
The macro CAN_FRAME_LEN_MAX and CANFD_FRAME_LEN_MAX are kept as an
alias to, respectively, can_frame_bytes(false, true, CAN_MAX_DLEN) and
can_frame_bytes(true, true, CANFD_MAX_DLEN).
In addition to the above:
- Use ISO 11898-1:2015 definitions for the names of the CAN frame
fields.
- Include linux/bits.h for use of BITS_PER_BYTE.
- Include linux/math.h for use of mult_frac() and
DIV_ROUND_UP(). N.B: the use of DIV_ROUND_UP() is not new to this
patch, but the include was previously omitted.
- Add copyright 2023 for myself.
Suggested-by: Thomas Kopp <Thomas.Kopp@microchip.com>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Reviewed-by: Thomas Kopp <Thomas.Kopp@microchip.com>
Link: https://lore.kernel.org/all/20230611025728.450837-4-mailhol.vincent@wanadoo.fr
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch aligns code to match open parenthesis and removes a
trailing whitespace.
Fixes: eb38c2053b ("can: rx-offload: rename can_rx_offload_queue_sorted() -> can_rx_offload_queue_timestamp()")
Fixes: f5071d9e72 ("can: m_can: m_can_handle_bus_errors(): add support for handling DLEC error on CAN-FD frames")
Reported-by: Judith Mendez <jm@ti.com>
Link: https://lore.kernel.org/all/20230523062410.1984098-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In their RZN1 SoC, Renesas put a CAN controller supposed to act very
similarly to the original Philips sja1000. In practice, while flooding
the bus with another device, we discovered that the controller very
often after an overrun situation would just refuse any new frame, drop
them all and trigger over and over again the overrun interrupt, even
though the buffer would have been totally emptied. The controller acts
like if its internal buffer offsets (where it writes and where the host
reads) where totally screwed-up.
Renesas manual mentions a single action to perform in order to
resynchronize the read and write offsets within the buffer: performing
a soft reset.
Performing a soft reset takes a bit of time and involves small delays,
so better do that in a threaded handler rather than inside the hard IRQ
handler.
Add platform data to recognize the platforms which need this workaround,
and when the faulty situation is diagnosed, stop what is being
performed and request the threaded handler to be executed in order to
perform the reset.
Tested-by: Jérémie Dautheribes <jeremie.dautheribes@bootlin.com> # 5.10
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/all/20230616134553.2786391-2-miquel.raynal@bootlin.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In order to support a flavor of the sja1000 which sometimes freezes, it
will be needed upon certain interrupts to perform a soft reset. The soft
reset operation takes a bit of time, so better not do it within the hard
interrupt handler but rather in a threaded handler. Let's prepare the
possibility for sja1000_err() to request "interrupting" the current flow
and request the threaded handler to be run while keeping the interrupt
line low.
There is no functional change.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/all/20230616134553.2786391-1-miquel.raynal@bootlin.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Rename the following macros:
- ESD_RTR to ESD_USB_RTR
- ESD_EV_CAN_ERROR_EXT to ESD_USB_EV_CAN_ERROR_EXT
Additionally remove the double newline trailing to definition
of ESD_USB_RTR.
Signed-off-by: Frank Jungclaus <frank.jungclaus@esd.eu>
Link: https://lore.kernel.org/r/20230523173105.3175086-3-frank.jungclaus@esd.eu
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add the consistent prefix ESD_USB_ to all macros defined within
esd_usb.c.
For macros specific to esd CAN-USB/2 use ESD_USB_2_ as prefix.
For macros specific to esd CAN-USB/Micro use ESD_USB_M_ as prefix.
Change the macro ESD_USB_3_SAMPLES to ESD_USB_TRIPLE_SAMPLES to not
mix up with the prefix ESD_USB_3_ which will be introduced for the
CAN-USB/3 device.
Link: https://lore.kernel.org/all/CAMZ6RqLaDNy-fZ2G0+QMhUEckkXLL+ZyELVSDFmqpd++aBzZQg@mail.gmail.com/
Suggested-by: Vincent MAILHOL <mailhol.vincent@wanadoo.fr>
Signed-off-by: Frank Jungclaus <frank.jungclaus@esd.eu>
Link: https://lore.kernel.org/r/20230519195600.420644-4-frank.jungclaus@esd.eu
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Currently the xilinx_can driver does not support adding a phy like the
"ti,tcan1043" to its devicetree.
This code makes it possible to add such phy, so that the kernel makes
sure that the PHY is in operational state, when the link is set to an
"up" state.
Signed-off-by: Marcel Hellwig <git@cookiesoft.de>
Link: https://lore.kernel.org/r/20230417085204.179268-1-git@cookiesoft.de
[mkl: call phy_power_off() after pm_runtime_put()]
[mkl: remove error message for phy_power_on() failure]
[mkl: update kernel-doc for struct xcan_priv]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Conflicts:
drivers/net/ethernet/freescale/fec_main.c
6ead9c98ca ("net: fec: remove the xdp_return_frame when lack of tx BDs")
144470c88c ("net: fec: using the standard return codes when xdp xmit errors")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Under certain circumstances we send two EFLUSH commands, resulting in two
EFLUSH ack packets, while only expecting a single EFLUSH ack.
This can cause the driver Tx flush completion to get out of sync.
To avoid this problem, don't enable the "Transmit buffer flush done" (TFD)
interrupt and remove the code handling it.
Now we only send EFLUSH command after receiving status packet with
"Init detected" (IDET) bit set.
Fixes: 26ad340e58 ("can: kvaser_pciefd: Add driver for Kvaser PCIEcan devices")
Cc: stable@vger.kernel.org
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/r/20230516134318.104279-6-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Empty the "Shared receive buffer" (SRB) in probe, to assure we start in a
known state, and don't process any irrelevant packets.
Fixes: 26ad340e58 ("can: kvaser_pciefd: Add driver for Kvaser PCIEcan devices")
Cc: stable@vger.kernel.org
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/r/20230516134318.104279-5-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The listen-only bit was never cleared, causing the controller to
always use listen-only mode, if previously set.
Fixes: 26ad340e58 ("can: kvaser_pciefd: Add driver for Kvaser PCIEcan devices")
Cc: stable@vger.kernel.org
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/r/20230516134318.104279-3-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Set can.state to CAN_STATE_STOPPED in kvaser_pciefd_stop().
Without this fix, wrong CAN state was repported after the interface was
brought down.
Fixes: 26ad340e58 ("can: kvaser_pciefd: Add driver for Kvaser PCIEcan devices")
Cc: stable@vger.kernel.org
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/r/20230516134318.104279-2-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230512212725.143824-20-u.kleine-koenig@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230512212725.143824-19-u.kleine-koenig@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Gerhard Bertelsmann <info@gerhard-bertelsmann.de>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20230512212725.143824-18-u.kleine-koenig@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230512212725.143824-17-u.kleine-koenig@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230512212725.143824-16-u.kleine-koenig@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230512212725.143824-15-u.kleine-koenig@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert these drivers from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230512212725.143824-14-u.kleine-koenig@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230512212725.143824-13-u.kleine-koenig@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230512212725.143824-12-u.kleine-koenig@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230512212725.143824-11-u.kleine-koenig@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230512212725.143824-10-u.kleine-koenig@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230512212725.143824-9-u.kleine-koenig@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230512212725.143824-8-u.kleine-koenig@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Link: https://lore.kernel.org/r/20230512212725.143824-7-u.kleine-koenig@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230512212725.143824-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230512212725.143824-5-u.kleine-koenig@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230512212725.143824-4-u.kleine-koenig@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230512212725.143824-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20230512212725.143824-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The print function dev_err() is redundant because
platform_get_irq_byname() already prints an error.
./drivers/net/can/bxcan.c:970:2-9: line 970 is redundant because platform_get_irq() already prints an error.
./drivers/net/can/bxcan.c:964:2-9: line 964 is redundant because platform_get_irq() already prints an error.
./drivers/net/can/bxcan.c:958:2-9: line 958 is redundant because platform_get_irq() already prints an error.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=4878
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/all/20230506080725.68401-1-jiapeng.chong@linux.alibaba.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds support for Fintek USB to 2CAN controller.
Changelog:
v7: https://lore.kernel.org/all/20230509073821.25289-1-peter_hong@fintek.com.tw
1. Fix consistency of coding style for "break" in f81604_register_urbs().
2. Remove goto statement in f81604_open().
v6: https://lore.kernel.org/all/20230505022317.22417-1-peter_hong@fintek.com.tw
1. Remove non-used define and change constant mask to GENMASK().
2. Move some variables declaration from function start to block start.
3. Move some variables initization into declaration.
4. Change variable "id" in f81604_start_xmit() only for CAN ID usage.
v5: https://lore.kernel.org/all/20230420024403.13830-1-peter_hong@fintek.com.tw
1. Change all u8 *buff to struct f81604_int_data/f81604_can_frame.
2. Change all netdev->dev_id to netdev->dev_port.
3. Remove over design for f81604_process_rx_packet(). This device only
report a frame at once, so the f81604_process_rx_packet() are reduced
to process 1 frame.
v4: https://lore.kernel.org/all/20230413084253.1524-1-peter_hong@fintek.com.tw
1. Remove f81604_prepare_urbs/f81604_remove_urbs() and alloc URB/buffer
dynamically in f81604_register_urbs(), using "urbs_anchor" for manage
all rx/int URBs.
2. Add F81604 to MAINTAINERS list.
3. Change handle_clear_reg_work/handle_clear_overrun_work to single
clear_reg_work and using bitwise "clear_flags" to record it.
4. Move __f81604_set_termination in front of f81604_probe() to avoid
rarely racing condition.
5. Add __aligned to struct f81604_int_data / f81604_sff / f81604_eff.
6. Add aligned operations in f81604_start_xmit/f81604_process_rx_packet().
7. Change lots of CANBUS functions first parameter from struct usb_device*
to struct f81604_port_priv *priv. But remain f81604_write / f81604_read
/ f81604_update_bits() as struct usb_device* for
__f81604_set_termination() in probe() stage.
8. Simplify f81604_read_int_callback() and separate into
f81604_handle_tx / f81604_handle_can_bus_errors() functions.
v3: https://lore.kernel.org/all/20230327051048.11589-1-peter_hong@fintek.com.tw
1. Change CAN clock to using MEGA units.
2. Remove USB set/get retry, only remain SJA1000 reset/operation retry.
3. Fix all numberic constant to define.
4. Add terminator control. (only 0 & 120 ohm)
5. Using struct data to represent INT/TX/RX endpoints data instead byte
arrays.
6. Error message reports changed from %d to %pe for mnemotechnic values.
7. Some bit operations are changed to FIELD_PREP().
8. Separate TX functions from f81604_read_int_callback().
9. cf->can_id |= CAN_ERR_CNT in f81604_read_int_callback to report valid
TX/RX error counts.
10. Move f81604_prepare_urbs/f81604_remove_urbs() from CAN open/close() to
USB probe/disconnect().
11. coding style refactoring.
v2: https://lore.kernel.org/all/20230321081152.26510-1-peter_hong@fintek.com.tw
1. coding style refactoring.
2. some const number are defined to describe itself.
3. fix wrong usage for can_get_echo_skb() in f81604_write_bulk_callback().
v1: https://lore.kernel.org/all/20230317093352.3979-1-peter_hong@fintek.com.tw
Signed-off-by: Ji-Ze Hong (Peter Hong) <peter_hong@fintek.com.tw>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/all/20230509073821.25289-1-peter_hong@fintek.com.tw
[mkl: add changelog, fix printf format]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The STMicroelectronics STM32 basic extended CAN Controller (bxCAN) is
only present on STM32 SoCs. Hence drop the "|| OF" part from its
dependency rule, to prevent asking the user about this driver when
configuring a kernel without STM32 SoC support.
Fixes: f00647d812 ("can: bxcan: add support for ST bxCAN controller")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/all/40095112efd1b2214e4223109fd9f0c6d0158a2d.1680609318.git.geert+renesas@glider.be
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
can_put_echo_skb() checks for the enabled IFF_ECHO flag and the
correct ETH_P type of the given skbuff. When implementing the CAN XL
support the new check for ETH_P_CANXL has been forgotten.
Fixes: fb08cba12b ("can: canxl: update CAN infrastructure for CAN XL frames")
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/all/20230506184515.39241-1-socketcan@hartkopp.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
USB IDs are usually represented in 16 bit hexadecimal values. To match
the common representation in lsusb and for searching USB IDs in the
internet convert the decimal values to lowercase hexadecimal.
changes since v1: https://lore.kernel.org/all/20230327175344.4668-1-socketcan@hartkopp.net
- drop the aligned block indentation (suggested by Jimmy)
- use lowercase hex values (suggested by Alex)
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Jimmy Assarsson <extja@kvaser.com>
Reviewed-by: Alexander Dahl <ada@thorsis.com>
Link: https://lore.kernel.org/all/20230329090915.3127-1-socketcan@hartkopp.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Announce that the driver supports CAN_CTRLMODE_BERR_REPORTING by means
of priv->can.ctrlmode_supported. Until now berr reporting always has
been active without taking care of the berr-reporting parameter given
to an "ip link set ..." command.
Additionally apply some changes to function esd_usb_rx_event():
- If berr reporting is off and it is also no state change, then
immediately return.
- Unconditionally (even in case of the above "immediate return") store
tx- and rx-error counters, so directly use priv->bec.txerr and
priv->bec.rxerr instead of intermediate variables.
- Not directly related, but to better point out the linkage between a
failed alloc_can_err_skb() and stats->rx_dropped++:
Move the increment of the rx_dropped statistic counter (back) to
directly behind the err_skb allocation.
Signed-off-by: Frank Jungclaus <frank.jungclaus@esd.eu>
Link: https://lore.kernel.org/all/20230330184446.2802135-1-frank.jungclaus@esd.eu
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add support for the basic extended CAN controller (bxCAN) found in many
low- to middle-end STM32 SoCs. It supports the Basic Extended CAN
protocol versions 2.0A and B with a maximum bit rate of 1 Mbit/s.
The controller supports two channels (CAN1 as primary and CAN2 as
secondary) and the driver can enable either or both of the channels. They
share some of the required logic (e. g. clocks and filters), and that means
you cannot use the secondary CAN without enabling some hardware resources
managed by the primary CAN.
Each channel has 3 transmit mailboxes, 2 receive FIFOs with 3 stages and
28 scalable filter banks.
It also manages 4 dedicated interrupt vectors:
- transmit interrupt
- FIFO 0 receive interrupt
- FIFO 1 receive interrupt
- status change error interrupt
Driver uses all 3 available mailboxes for transmission and FIFO 0 for
reception. Rx filter rules are configured to the minimum. They accept
all messages and assign filter 0 to CAN1 and filter 14 to CAN2 in
identifier mask mode with 32 bits width. It enables and uses transmit,
receive buffers for FIFO 0 and error and status change interrupts.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/all/20230328073328.3949796-6-dario.binacchi@amarulasolutions.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Interrupts currently get disabled if the interrupt status shows new
received data. Non-peripheral chips handle receiving in a worker thread,
but peripheral chips are handling the receive process in the threaded
interrupt routine itself without scheduling it for a different worker.
So there is no need to disable interrupts for peripheral chips.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/all/20230315110546.2518305-6-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
There are a number of interrupts that are not used by the driver at the
moment. Disable all of these.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/all/20230315110546.2518305-5-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Interrupts are enabled a few lines further down as well. Remove this
second call to enable all interrupts.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/all/20230315110546.2518305-4-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The code already exits the function on !ir before this condition. No
need to check again if anything is set as IR_ALL_INT is 0xffffffff.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/all/20230315110546.2518305-3-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Merge both if-blocks to fix this.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/all/20230315110546.2518305-2-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Remove pci_clear_master to simplify the code,
the bus-mastering is also cleared in do_pci_disable_device,
like this:
./drivers/pci/pci.c:2197
static void do_pci_disable_device(struct pci_dev *dev)
{
u16 pci_command;
pci_read_config_word(dev, PCI_COMMAND, &pci_command);
if (pci_command & PCI_COMMAND_MASTER) {
pci_command &= ~PCI_COMMAND_MASTER;
pci_write_config_word(dev, PCI_COMMAND, pci_command);
}
pcibios_disable_device(dev);
}.
And dev->is_busmaster is set to 0 in pci_disable_device.
Signed-off-by: Cai Huoqing <cai.huoqing@linux.dev>
Link: https://lore.kernel.org/all/20230323113318.9473-3-cai.huoqing@linux.dev
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Remove pci_clear_master to simplify the code,
the bus-mastering is also cleared in do_pci_disable_device,
like this:
./drivers/pci/pci.c:2197
static void do_pci_disable_device(struct pci_dev *dev)
{
u16 pci_command;
pci_read_config_word(dev, PCI_COMMAND, &pci_command);
if (pci_command & PCI_COMMAND_MASTER) {
pci_command &= ~PCI_COMMAND_MASTER;
pci_write_config_word(dev, PCI_COMMAND, pci_command);
}
pcibios_disable_device(dev);
}.
And dev->is_busmaster is set to 0 in pci_disable_device.
Signed-off-by: Cai Huoqing <cai.huoqing@linux.dev>
Link: https://lore.kernel.org/all/20230323113318.9473-2-cai.huoqing@linux.dev
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Remove pci_clear_master to simplify the code,
the bus-mastering is also cleared in do_pci_disable_device,
like this:
./drivers/pci/pci.c:2197
static void do_pci_disable_device(struct pci_dev *dev)
{
u16 pci_command;
pci_read_config_word(dev, PCI_COMMAND, &pci_command);
if (pci_command & PCI_COMMAND_MASTER) {
pci_command &= ~PCI_COMMAND_MASTER;
pci_write_config_word(dev, PCI_COMMAND, pci_command);
}
pcibios_disable_device(dev);
}.
And dev->is_busmaster is set to 0 in pci_disable_device.
Signed-off-by: Cai Huoqing <cai.huoqing@linux.dev>
Link: https://lore.kernel.org/all/20230323113318.9473-1-cai.huoqing@linux.dev
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Improve printed error messages:
- Replace numerical error codes by mnemotechnic error codes, to
improve the user experience in case of errors,
- Drop parentheses around printed numbers, cfr.
Documentation/process/coding-style.rst,
- Drop printing of an error message in case of out-of-memory, as the
core memory allocation code already takes care of this.
Suggested-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/all/4162cc46f72257ec191007675933985b6df394b9.1679414936.git.geert+renesas@glider.be
[mkl: use colon instead of comma]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add support for CAN transceivers described as PHYs.
While simple CAN transceivers can do without, this is needed for CAN
transceivers like NXP TJR1443 that need a configuration step (like
pulling standby or enable lines), and/or impose a bitrate limit.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/all/1ce907572ac1d4e1733fa6ea7712250f2229cfcb.1679414936.git.geert+renesas@glider.be
[mkl: squash error message update from patch 2]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
It is preferred to use typed property access functions (i.e.
of_property_read_<type> functions) rather than low-level
of_get_property/of_find_property functions for reading properties.
Convert reading boolean properties to of_property_read_bool().
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for net/can
Acked-by: Kalle Valo <kvalo@kernel.org>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the supply for cf->data[3] (bit stream position of CAN error), in
case of a bus- or protocol-error, outside of the "switch (ecc &
SJA1000_ECC_MASK){}"-statement, because this bit stream position is
independent of the error type.
Fixes: 96d8e90382 ("can: Add driver for esd CAN-USB/2 device")
Signed-off-by: Frank Jungclaus <frank.jungclaus@esd.eu>
Link: https://lore.kernel.org/all/20230216190450.3901254-2-frank.jungclaus@esd.eu
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to Use devm_platform_ioremap_resource(), as this is exactly what
this function does.
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Acked-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Link: https://lore.kernel.org/all/20230216090610.130860-1-yang.lee@linux.alibaba.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEDs2BvajyNKlf9TJQvlAcSiqKBOgFAmPg+r4THG1rbEBwZW5n
dXRyb25peC5kZQAKCRC+UBxKKooE6A44B/0c8jjyLikVE2fEBKkvPk8iRlFKap48
140HNR+1TuVBBPCJTe2Gq3l8fDfFUgUVnFfVDjAQq6pMWufLkz9jVr5uGN7O94v+
tFCjip8NLRTa6ibgQlGrFXl31X5vqT+jV6V4l29wFgbwgOMRrod7wLDo+bHTtuuY
46Sf4GgIazYjxEeZBBsvjnAbraFq0twZFcEz9SyeOxqjR+9+71X4Y3x0kgQuz72N
CrvRng0yFLqbHOBE60iaDqbjuNnwBGTH476pwX25Kj9gVyIH20T45h8tV4j6z2Sq
A42cHKDlWZRWUiWQjGOHHT4igUf//Sfv8WDaFjqobO/DDY+nBA75EPAv
=hWLT
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-6.3-20230206' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2023-02-06
this is a pull request of 47 patches for net-next/master.
The first two patch is by Oliver Hartkopp. One adds missing error
checking to the CAN_GW protocol, the other adds a missing CAN address
family check to the CAN ISO TP protocol.
Thomas Kopp contributes a performance optimization to the mcp251xfd
driver.
The next 11 patches are by Geert Uytterhoeven and add support for
R-Car V4H systems to the rcar_canfd driver.
Stephane Grosjean and Lukas Magel contribute 8 patches to the peak_usb
driver, which add support for configurable CAN channel ID.
The last 17 patches are by me and target the CAN bit timing
configuration. The bit timing is cleaned up, error messages are
improved and forwarded to user space via NL_SET_ERR_MSG_FMT() instead
of netdev_err(), and the SJW handling is updated, including the
definition of a new default value that will benefit CAN-FD
controllers, by increasing their oscillator tolerance.
* tag 'linux-can-next-for-6.3-20230206' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next: (47 commits)
can: bittiming: can_validate_bitrate(): report error via netlink
can: bittiming: can_calc_bittiming(): convert from netdev_err() to NL_SET_ERR_MSG_FMT()
can: bittiming: can_calc_bittiming(): clean up SJW handling
can: bittiming: can_sjw_set_default(): use Phase Seg2 / 2 as default for SJW
can: bittiming: can_sjw_check(): check that SJW is not longer than either Phase Buffer Segment
can: bittiming: can_sjw_check(): report error via netlink and harmonize error value
can: bittiming: can_fixup_bittiming(): report error via netlink and harmonize error value
can: bittiming: factor out can_sjw_set_default() and can_sjw_check()
can: bittiming: can_changelink() pass extack down callstack
can: netlink: can_changelink(): convert from netdev_err() to NL_SET_ERR_MSG_FMT()
can: netlink: can_validate(): validate sample point for CAN and CAN-FD
can: dev: register_candev(): bail out if both fixed bit rates and bit timing constants are provided
can: dev: register_candev(): ensure that bittiming const are valid
can: bittiming: can_get_bittiming(): use direct return and remove unneeded else
can: bittiming: can_fixup_bittiming(): set effective tq
can: bittiming: can_fixup_bittiming(): use CAN_SYNC_SEG instead of 1
can: bittiming(): replace open coded variants of can_bit_time()
can: peak_usb: Reorder include directives alphabetically
can: peak_usb: align CAN channel ID format in log with sysfs attribute
can: peak_usb: export PCAN CAN channel ID as sysfs device attribute
...
====================
Link: https://lore.kernel.org/r/20230206131620.2758724-1-mkl@pengutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Replace the netdev_err() by NL_SET_ERR_MSG_FMT() to better inform the
user about the problem. While there, use %u to print unsigned values
and improve error message a bit.
In case of an error, return -EINVAL instead of -EDOM, this corresponds
better to the actual meaning of the error value.
Link: https://lore.kernel.org/all/20230202110854.2318594-17-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
"The (Re-)Synchronization Jump Width (SJW) defines how far a
resynchronization may move the Sample Point inside the limits defined
by the Phase Buffer Segments to compensate for edge phase errors." [1]
In other words, this means that the SJW parameter controls the
tolerance of the CAN controller to frequency errors compared to other
CAN controllers.
If the user space does not provide an SJW parameter, the kernel
chooses a default value of 1. This has proven to be a good default
value for classic CAN controllers, but no longer for modern CAN-FD
controllers.
In the past there were CAN controllers like the sja1000 with a rather
limited range of bit timing parameters. For the standard bit rates
this results in the following bit timing parameters:
| Bit timing parameters for sja1000 with 8.000000 MHz ref clock
| _----+--------------=> tseg1: 1 … 16
| / / _---------=> tseg2: 1 … 8
| | | / _-----=> sjw: 1 … 4
| | | | / _-=> brp: 1 … 64 (inc: 1)
| | | | | /
| nominal | | | | | real Bitrt nom real SampP
| Bitrate TQ[ns] PrS PhS1 PhS2 SJW BRP Bitrate Error SampP SampP Error BTR0 BTR1
| 1000000 125 2 3 2 1 1 1000000 0.0% 75.0% 75.0% 0.0% 0x00 0x14
| 800000 125 3 4 2 1 1 800000 0.0% 80.0% 80.0% 0.0% 0x00 0x16
| 666666 125 4 4 3 1 1 666666 0.0% 80.0% 75.0% 6.2% 0x00 0x27
| 500000 125 6 7 2 1 1 500000 0.0% 87.5% 87.5% 0.0% 0x00 0x1c
| 250000 250 6 7 2 1 2 250000 0.0% 87.5% 87.5% 0.0% 0x01 0x1c
| 125000 500 6 7 2 1 4 125000 0.0% 87.5% 87.5% 0.0% 0x03 0x1c
| 100000 625 6 7 2 1 5 100000 0.0% 87.5% 87.5% 0.0% 0x04 0x1c
| 83333 750 6 7 2 1 6 83333 0.0% 87.5% 87.5% 0.0% 0x05 0x1c
| 50000 1250 6 7 2 1 10 50000 0.0% 87.5% 87.5% 0.0% 0x09 0x1c
| 33333 1875 6 7 2 1 15 33333 0.0% 87.5% 87.5% 0.0% 0x0e 0x1c
| 20000 3125 6 7 2 1 25 20000 0.0% 87.5% 87.5% 0.0% 0x18 0x1c
| 10000 6250 6 7 2 1 50 10000 0.0% 87.5% 87.5% 0.0% 0x31 0x1c
The attentive reader will notice that the SJW is 1 in most cases,
while the Seg2 phase is 2. Both values are given in TQ units, which in
turn is a duration in nanoseconds.
For example the 500 kbit/s configuration:
| nominal real Bitrt nom real SampP
| Bitrate TQ[ns] PrS PhS1 PhS2 SJW BRP Bitrate Error SampP SampP Error BTR0 BTR1
| 500000 125 6 7 2 1 1 500000 0.0% 87.5% 87.5% 0.0% 0x00 0x1c
the TQ is 125ns, the Phase Seg2 is "2" (== 250ns), the SJW is "1" (==
125 ns).
Looking at a more modern CAN controller like a mcp2518fd, it has wider
bit timing registers.
| Bit timing parameters for mcp251xfd with 40.000000 MHz ref clock
| _----+--------------=> tseg1: 2 … 256
| / / _---------=> tseg2: 1 … 128
| | | / _-----=> sjw: 1 … 128
| | | | / _-=> brp: 1 … 256 (inc: 1)
| | | | | /
| nominal | | | | | real Bitrt nom real SampP
| Bitrate TQ[ns] PrS PhS1 PhS2 SJW BRP Bitrate Error SampP SampP Error NBTCFG
| 500000 25 34 35 10 1 1 500000 0.0% 87.5% 87.5% 0.0% 0x00440900
The TQ is 25ns, the Phase Seg 2 is "10" (== 250ns), the SJW is "1" (==
25ns).
Since the kernel chooses a default SJW of 1 regardless of the TQ, this
leads to a much smaller SJW and thus much smaller tolerances to
frequency errors.
To maintain the same oscillator tolerances on controllers with wide
bit timing registers, select a default SJW value of Phase Seg2 / 2
unless Phase Seg 1 is less. This results in the following bit timing
parameters:
| Bit timing parameters for mcp251xfd with 40.000000 MHz ref clock
| _----+--------------=> tseg1: 2 … 256
| / / _---------=> tseg2: 1 … 128
| | | / _-----=> sjw: 1 … 128
| | | | / _-=> brp: 1 … 256 (inc: 1)
| | | | | /
| nominal | | | | | real Bitrt nom real SampP
| Bitrate TQ[ns] PrS PhS1 PhS2 SJW BRP Bitrate Error SampP SampP Error NBTCFG
| 500000 25 34 35 10 5 1 500000 0.0% 87.5% 87.5% 0.0% 0x00440904
The TQ is 25ns, the Phase Seg 2 is "10" (== 250ns), the SJW is "5" (==
125ns). Which is the same as on the sja1000 controller.
[1] http://web.archive.org/http://www.oertel-halle.de/files/cia99paper.pdf
Link: https://lore.kernel.org/all/20230202110854.2318594-15-mkl@pengutronix.de
Cc: Mark Bath <mark@baggywrinkle.co.uk>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
If the user space has supplied an invalid SJW value (greater than the
maximum SJW value), report -EINVAL instead of -ERANGE, this better
matches the actual meaning of the error value.
Additionally report an error message via netlink to the user space.
Link: https://lore.kernel.org/all/20230202110854.2318594-13-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Check each bit timing parameter first individually against their
limits and report a meaningful error message via netlink to the user
space.
In case of an error, return -EINVAL instead of -ERANGE, this
corresponds better to the actual meaning of the error value.
Link: https://lore.kernel.org/all/20230202110854.2318594-12-mkl@pengutronix.de
Suggested-by: Vincent Mailhol <vincent.mailhol@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Factor out the functionality of assigning a SJW default value into
can_sjw_set_default() and the checking the SJW limits into
can_sjw_check().
This functions will be improved and called from a different function
in the following patches.
Link: https://lore.kernel.org/all/20230202110854.2318594-11-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This is a preparation patch.
In order to pass warning/error messages during netlink calls back to
user space, pass the extack struct down the callstack of
can_changelink(), the actual error messages will be added in the
following ptaches.
Link: https://lore.kernel.org/all/20230202110854.2318594-10-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Since commit 51c352bdbc ("netlink: add support for formatted extack
messages") formatted extack messages are supported to inform the user
space or warnings/errors during netlink calls.
Replace the netdev_err() by NL_SET_ERR_MSG_FMT() to better inform the
user about the problem. While there, use %u to print unsigned values
and improve error message a bit.
Link: https://lore.kernel.org/all/20230202110854.2318594-9-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The sample point is a value in tenths of a percent. Meaningful values
are between 0 and 1000. Invalid values are rejected and an error
message is returned to user space via netlink.
Link: https://lore.kernel.org/all/20230202110854.2318594-8-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Implement the function can_bittiming_const_valid() to check the
validity of the specified bit timing constant. Call this function from
register_candev() to check the bit timing constants during the
registration of the CAN interface.
Link: https://lore.kernel.org/all/20230202110854.2318594-6-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The can_fixup_bittiming() function is used to validate the
user-supplied low-level bit timing parameters and calculate the
bitrate prescaler (brp) from the requested time quanta (tq) and the
CAN clock of the controller.
can_fixup_bittiming() selects the best matching integer bit rate
prescaler, which may result in a different time quantum than the value
specified by the user.
Calculate the resulting time quantum and assign it so that the user
sees the effective time quantum.
Link: https://lore.kernel.org/all/20230202110854.2318594-4-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Commit 1c47fa6b31 ("can: dev: add a helper function to calculate the
duration of one bit") made the constant CAN_SYNC_SEG available in a
header file.
The magic number 1 in can_fixup_bittiming() represents the width of
the sync segment, replace it by CAN_SYNC_SEG to make the code more
readable.
Link: https://lore.kernel.org/all/20230202110854.2318594-3-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Commit 1c47fa6b31 ("can: dev: add a helper function to calculate the
duration of one bit") added the helper function can_bit_time().
Replace open coded variants of can_bit_time() by the helper function.
Link: https://lore.kernel.org/all/20230202110854.2318594-2-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The include directives in all source files are reordered alphabetically
according to the names of the header files.
Signed-off-by: Lukas Magel <lukas.magel@posteo.net>
Link: https://lore.kernel.org/all/20230116200932.157769-9-lukas.magel@posteo.net
[mkl: move header changes from Patch 3 here]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Previously, the CAN channel ID was printed to the kernel log in decimal
upon connecting a new PEAK device. This behavior is inconsistent with
the hexadecimal format of the CAN channel ID sysfs attribute. This patch
updates the log message to output the id in hexadecimal.
Signed-off-by: Lukas Magel <lukas.magel@posteo.net>
Link: https://lore.kernel.org/all/20230116200932.157769-8-lukas.magel@posteo.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch exports the CAN channel ID as a sysfs attribute. The CAN
channel ID is a user-configurable u8/u32 identifier that can be set
individually for each CAN interface of a PEAK USB device.
Exporting the channel ID as a sysfs attribute allows users to easily read
the ID and to write udev rules that can match against the ID. This is
especially useful for PEAK USB devices that do not export a serial
number at SUB level.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Lukas Magel <lukas.magel@posteo.net>
Link: https://lore.kernel.org/all/20230116200932.157769-7-lukas.magel@posteo.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch introduces 3 new functions implementing support for ethtool
access to the CAN channel ID of all USB CAN network interfaces managed by
the driver. With this patch, it is possible to read/write the CAN
channel ID from/to the EEPROM via the ethtool interface.
The CAN channel ID is a user-configurable device identifier that can be
set individually for each CAN interface of a PEAK USB device. Depending on
the device, the identifier has a length of 8 or 32 bit. The identifier
is stored in the non-volatile memory of the device.
The identifier of a CAN interface can be read/written as an 8 or 32 bit
byte string in native (little-endian) byte order, where the length depends
on the device type.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Lukas Magel <lukas.magel@posteo.net>
Link: https://lore.kernel.org/all/20230116200932.157769-6-lukas.magel@posteo.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch changes the call to unregister_netdev() in
peak_usb_disconnect() with unregister_candev().
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Lukas Magel <lukas.magel@posteo.net>
Link: https://lore.kernel.org/all/20230116200932.157769-5-lukas.magel@posteo.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds callbacks that allow the user to set a new self-defined
CAN channel ID to all USB - CAN/CANFD interfaces of PEAK-System managed by
this driver, namely:
- PCAN-USB
- PCAN-USB FD
- PCAN-USB Pro FD
- PCAN-USB X6
- PCAN-Chip USB
- PCAN-USB Pro
The callback functions write the CAN channel ID to the non-volatile
memory of the devices.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Lukas Magel <lukas.magel@posteo.net>
Link: https://lore.kernel.org/all/20230116200932.157769-4-lukas.magel@posteo.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds a new function that allows to read the CAN channel ID
from the non volatile memory of the USB CAN-FD PEAK devices. The CAN
channel ID is a user-configurable u8/u32 identifier value that can be set
individually for each PEAK CAN interface.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Lukas Magel <lukas.magel@posteo.net>
Link: https://lore.kernel.org/all/20230116200932.157769-3-lukas.magel@posteo.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The so-called "device id" is a user-defined identifier value that can be
set individually for each CAN interface of a PEAK USB device.
Contrary to a static serial number, the value can be changed by the
user. With this ID, each CAN interface can be uniquely identified even if
the USB device does not export a proper serial number or the USB device
exports multiple CAN interfaces. In order to not confuse it with the
device ID used by the USB core and emphasize the link to the CAN
interface, the functions and variables for reading this user-defined
value are renamed to CAN channel ID.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Lukas Magel <lukas.magel@posteo.net>
Link: https://lore.kernel.org/all/20230116200932.157769-2-lukas.magel@posteo.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The reset line from the Asix chip to the SJA1000 is asserted after boot up
until it is deasserted by a register write
Signed-off-by: Gerhard Uttenthaler <uttenthaler@ems-wuensche.com>
Link: https://lore.kernel.org/all/20230120112616.6071-8-uttenthaler@ems-wuensche.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
On R-Car Gen4 CAN_FD variants, the Data Bit Rate Resynchronization Jump
Width Control (DSJW) field in the Channel n Data Bitrate Configuration
Register (DCFG) register is one bit wider than on older variants.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/all/c4e8bc220bf87e6c7e375f7a2ce51e2aa89ea8a7.1674499048.git.geert+renesas@glider.be
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Despite the name, R-Car V3U (R8A779A0) was the first member of the R-Car
Gen4 family. Generalize the support for R-Car V3U to other SoCs in the
R-Car Gen4 family by adding a family-specific compatible value, and by
replacing all references to "V3U" by "Gen4".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/all/61f6f34eb7bcc62ff604add98f1bcd2d2584187d.1674499048.git.geert+renesas@glider.be
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Abstract the different addresses for the Channel n Data Bitrate
Configuration Register (DCFG) in the definition of the register macro,
like is already done for other register definitions, to simplify code
accessing this register.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/all/13e02d710dac3ddef73aa4be2b995766db9b6b4d.1674499048.git.geert+renesas@glider.be
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Each Global Acceptance Filter List Configuration Register (GAFLCFG)
contains two fields, and stores the number of channel rules for one
channel pair.
As R-Car V3U and later can have more than 2 channels, the field
selection should be based on the LSB (even or odd) of the channel
number, instead of on the full channel number.
Fixes: 45721c406d ("can: rcar_canfd: Add support for r8a779a0 SoC")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/all/36bcf0ffb96d6aaed970751f9546b901af638bcf.1674499048.git.geert+renesas@glider.be
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When adding support for R-Car V3U, the Global FD Configuration register
(CFDGFDCFG) and the Channel-specific CAN-FD Configuration Registers
(CFDCmFDCFG) were mixed up. Use the correct register, and apply the
selected CAN mode to all available channels.
Annotate the corresponding register bits, to make it clear they do
not exist on older variants.
Fixes: 45721c406d ("can: rcar_canfd: Add support for r8a779a0 SoC")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/all/388ddf312917eb9f6cc460a481f68402a876f9b5.1674499048.git.geert+renesas@glider.be
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
If the a new ring layout is set, the max coalesced frames for RX and
TX are re-calculated, too. Add the missing assignment of the newly
calculated TX max coalesced frames.
Fixes: 656fc12dda ("can: mcp251xfd: add TX IRQ coalescing ethtool support")
Link: https://lore.kernel.org/all/20230130154334.1578518-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Debian's gcc-13 [1] throws the following error in
kvaser_usb_hydra_cmd_size():
[1] gcc version 13.0.0 20221214 (experimental) [master r13-4693-g512098a3316] (Debian 13-20221214-1)
| drivers/net/can/usb/kvaser_usb/kvaser_usb_hydra.c:502:65: error:
| array subscript ‘struct kvaser_cmd_ext[0]’ is partly outside array
| bounds of ‘unsigned char[32]’ [-Werror=array-bounds=]
| 502 | ret = le16_to_cpu(((struct kvaser_cmd_ext *)cmd)->len);
kvaser_usb_hydra_cmd_size() returns the size of given command. It
depends on the command number (cmd->header.cmd_no). For extended
commands (cmd->header.cmd_no == CMD_EXTENDED) the above shown code is
executed.
Help gcc to recognize that this code path is not taken in all cases,
by calling kvaser_usb_hydra_cmd_size() directly after assigning the
command number.
Fixes: aec5fb2268 ("can: kvaser_usb: Add support for Kvaser USB hydra family")
Cc: Jimmy Assarsson <extja@kvaser.com>
Cc: Anssi Hannula <anssi.hannula@bitwise.fi>
Link: https://lore.kernel.org/all/20221219110104.1073881-1-mkl@pengutronix.de
Tested-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When do suspend/resume, meet the following warning message:
[ 30.028336] flexcan 425b0000.can: Unbalanced pm_runtime_enable!
Balance the pm_runtime_force_suspend() and pm_runtime_force_resume().
Fixes: 8cb53b485f ("can: flexcan: add auto stop mode for IMX93 to support wakeup")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://lore.kernel.org/all/20221213094351.3023858-1-haibo.chen@nxp.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Specify exactly which registers are read/writeable in the chip. This
is supposed to help detect any violations in the future.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://lore.kernel.org/all/20221206115728.1056014-12-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
According to the datasheet 0x10 is the last register in the first block,
not register 0x2c.
The datasheet lists the last register of the second block as 0x830, not
0x83c.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://lore.kernel.org/all/20221206115728.1056014-11-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
TCAN4X5X_ERROR_STATUS is not a status register that needs clearing
during interrupt handling. Instead this is a masking register that masks
error interrupts. Writing TCAN4X5X_CLEAR_ALL_INT to this register
effectively masks everything.
Rename the register and mask all error interrupts only once by writing
to the register in tcan4x5x_init.
Fixes: 5443c226ba ("can: tcan4x5x: Add tcan4x5x driver to the kernel")
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://lore.kernel.org/all/20221206115728.1056014-10-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Register 0x824 TCAN4X5X_MCAN_INT_REG is a read-only register. Any writes
to this register do not have any effect.
Remove this write. The m_can driver aldready clears the interrupts in
m_can_isr() by writing to M_CAN_IR which is translated to register
0x1050 which is a writable version of this register.
Fixes: 5443c226ba ("can: tcan4x5x: Add tcan4x5x driver to the kernel")
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://lore.kernel.org/all/20221206115728.1056014-9-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Instead of acknowledging every item of the fifo, only acknowledge the
last item read. This behavior is documented in the datasheet. The new
getindex will be the acknowledged item + 1.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://lore.kernel.org/all/20221206115728.1056014-8-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Transmit events from the txe fifo can be batch acknowledged by
acknowledging the last read txe fifo item. This will save txe_count
writes which is important for peripheral chips.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://lore.kernel.org/all/20221206115728.1056014-7-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The getindex gets increased by one every time. We can calculate the
correct getindex in the driver and avoid the additional reads of rxfs.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://lore.kernel.org/all/20221206115728.1056014-6-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The getindex simply increases by one for every iteration. There is no
need to get the current getidx every time from a register. Instead we
can just count and wrap if necessary.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://lore.kernel.org/all/20221206115728.1056014-5-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
For peripheral devices the m_can_rx_handler is called directly after
setting cdev->irqstatus. This means we don't have to read the irqstatus
again in m_can_rx_handler. Avoid this by adding a parameter that is
false for direct calls.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://lore.kernel.org/all/20221206115728.1056014-3-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The TXFQS register is read first to check if the fifo is full and then
immediately again to get the putidx. This is unnecessary and adds
significant overhead if read requests are done over a slow bus, for
example SPI with tcan4x5x.
Add a variable to store the value of the register. Split the
m_can_tx_fifo_full function into two to avoid the hidden m_can_read call
if not needed.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://lore.kernel.org/all/20221206115728.1056014-2-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When we try to access the mcan message ram addresses during the probe,
hclk is gated by any other drivers or disabled, because of that probe
gets failed.
Move the mram init functionality to mcan chip config called by
m_can_start from mcan open function, by that time clocks are
enabled.
Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Vivek Yadav <vivek.2311@samsung.com>
Link: https://lore.kernel.org/all/20221207100632.96200-2-vivek.2311@samsung.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The iface field of struct gs_can is only used to retrieve the
usb_device which is already available in gs_can::udev.
Replace each occurrence of interface_to_usbdev(dev->iface) with
dev->udev. This done, remove gs_can::iface.
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/all/20221208081142.16936-3-mailhol.vincent@wanadoo.fr
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The implementation of strscpy() is more robust and safer.
That's now the recommended way to copy NUL terminated strings.
Signed-off-by: Xu Panda <xu.panda@zte.com.cn>
Signed-off-by: Yang Yang <yang.yang29@zte.com>
Link: https://lore.kernel.org/all/202212070909095189693@zte.com.cn
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Now that the product information are available under devlink, no more
need to print them in the kernel log. Remove es58x_get_product_info().
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/all/20221130174658.29282-7-mailhol.vincent@wanadoo.fr
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
ES58x devices report below product information through a custom usb
string:
* the firmware version
* the bootloader version
* the hardware revision
Parse this string, store the results in struct es58x_dev, export:
* the firmware version through devlink's "fw" name
* the bootloader version through devlink's "fw.bootloader" name
* the hardware revisionthrough devlink's "board.rev" name
Those devlink entries are not critical to use the device, if parsing
fails, print an informative log message and continue to probe the
device.
In addition to that, use usb_device::serial to report the device
serial number.
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/all/20221130174658.29282-6-mailhol.vincent@wanadoo.fr
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add support for devlink port which extends the devlink support to the
network interface level. For now, the etas_es58x driver will only rely
on the default features that devlink port has to offer and not
implement additional feature ones.
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/all/20221130174658.29282-3-mailhol.vincent@wanadoo.fr
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add basic support for devlink at the device level. The callbacks of
struct devlink_ops will be implemented next.
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/all/20221130174658.29282-2-mailhol.vincent@wanadoo.fr
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Link: https://lore.kernel.org/all/202211111443005202576@zte.com.cn
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
IMX93 do not contain a GPR to config the stop mode, it will set
the flexcan into stop mode automatically once the ARM core go
into low power mode (WFI instruct) and gate off the flexcan
related clock automatically. But to let these logic work as
expect, before ARM core go into low power mode, need to make
sure the flexcan related clock keep on.
To support stop mode and wakeup feature on imx93, this patch
add a new fsl_imx93_devtype_data to separate from imx8mp.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://lore.kernel.org/all/1669116752-4260-1-git-send-email-haibo.chen@nxp.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Follow the best practices, reorder the includes.
While doing so, bump up copyright year of each modified files.
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/all/20221126160525.87036-1-mailhol.vincent@wanadoo.fr
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Since commit 0166dc11be ("of: make CONFIG_OF user selectable"), it
is possible to test-build any driver which depends on OF on any
architecture by explicitly selecting OF. Therefore depending on
COMPILE_TEST as an alternative is no longer needed.
It is actually better to always build such drivers with OF enabled,
so that the test builds are closer to how each driver will actually be
built on its intended target. Building them without OF may not test
much as the compiler will optimize out potentially large parts of the
code. In the worst case, this could even pop false positive warnings.
Dropping COMPILE_TEST here improves the quality of our testing and
avoids wasting time on non-existent issues.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Cc: Ondrej Ille <ondrej.ille@gmail.com>
Acked-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Link: https://lore.kernel.org/all/20221124141604.4265225f@endymion.delvare
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
RZ/G2L has separate IRQ lines for tx and error interrupt for each
channel whereas R-Car has a combined IRQ line for all the channel
specific tx and error interrupts.
Add multi_channel_irqs to struct rcar_canfd_hw_info to select the
driver to choose between combined and separate irq registration for
channel interrupts. This patch also removes enum rcanfd_chip_id and
chip_id from both struct rcar_canfd_hw_info, as it is unused.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/all/20221027082158.95895-6-biju.das.jz@bp.renesas.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
R-Car has a clock divider for CAN FD clock within the IP, whereas
it is not available on RZ/G2L.
Add postdiv variable to struct rcar_canfd_hw_info to take care of this
difference.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/all/20221027082158.95895-5-biju.das.jz@bp.renesas.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
