The conversion of all GPIO drivers to using the .set_rv() and
.set_multiple_rv() callbacks from struct gpio_chip (which - unlike their
predecessors - return an integer and allow the controller drivers to
indicate failures to users) is now complete and the legacy ones have
been removed. Rename the new callbacks back to their original names in
one sweeping change.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Core & protocols
----------------
- Wrap datapath globals into net_aligned_data, to avoid false sharing.
- Preserve MSG_ZEROCOPY in forwarding (e.g. out of a container).
- Add SO_INQ and SCM_INQ support to AF_UNIX.
- Add SIOCINQ support to AF_VSOCK.
- Add TCP_MAXSEG sockopt to MPTCP.
- Add IPv6 force_forwarding sysctl to enable forwarding per interface.
- Make TCP validation of whether packet fully fits in the receive
window and the rcv_buf more strict. With increased use of HW
aggregation a single "packet" can be multiple 100s of kB.
- Add MSG_MORE flag to optimize large TCP transmissions via sockmap,
improves latency up to 33% for sockmap users.
- Convert TCP send queue handling from tasklet to BH workque.
- Improve BPF iteration over TCP sockets to see each socket exactly once.
- Remove obsolete and unused TCP RFC3517/RFC6675 loss recovery code.
- Support enabling kernel threads for NAPI processing on per-NAPI
instance basis rather than a whole device. Fully stop the kernel NAPI
thread when threaded NAPI gets disabled. Previously thread would stick
around until ifdown due to tricky synchronization.
- Allow multicast routing to take effect on locally-generated packets.
- Add output interface argument for End.X in segment routing.
- MCTP: add support for gateway routing, improve bind() handling.
- Don't require rtnl_lock when fetching an IPv6 neighbor over Netlink.
- Add a new neighbor flag ("extern_valid"), which cedes refresh
responsibilities to userspace. This is needed for EVPN multi-homing
where a neighbor entry for a multi-homed host needs to be synced
across all the VTEPs among which the host is multi-homed.
- Support NUD_PERMANENT for proxy neighbor entries.
- Add a new queuing discipline for IETF RFC9332 DualQ Coupled AQM.
- Add sequence numbers to netconsole messages. Unregister netconsole's
console when all net targets are removed. Code refactoring.
Add a number of selftests.
- Align IPSec inbound SA lookup to RFC 4301. Only SPI and protocol
should be used for an inbound SA lookup.
- Support inspecting ref_tracker state via DebugFS.
- Don't force bonding advertisement frames tx to ~333 ms boundaries.
Add broadcast_neighbor option to send ARP/ND on all bonded links.
- Allow providing upcall pid for the 'execute' command in openvswitch.
- Remove DCCP support from Netfilter's conntrack.
- Disallow multiple packet duplications in the queuing layer.
- Prevent use of deprecated iptables code on PREEMPT_RT.
Driver API
----------
- Support RSS and hashing configuration over ethtool Netlink.
- Add dedicated ethtool callbacks for getting and setting hashing fields.
- Add support for power budget evaluation strategy in PSE /
Power-over-Ethernet. Generate Netlink events for overcurrent etc.
- Support DPLL phase offset monitoring across all device inputs.
Support providing clock reference and SYNC over separate DPLL
inputs.
- Support traffic classes in devlink rate API for bandwidth management.
- Remove rtnl_lock dependency from UDP tunnel port configuration.
Device drivers
--------------
- Add a new Broadcom driver for 800G Ethernet (bnge).
- Add a standalone driver for Microchip ZL3073x DPLL.
- Remove IBM's NETIUCV device driver.
- Ethernet high-speed NICs:
- Broadcom (bnxt):
- support zero-copy Tx of DMABUF memory
- take page size into account for page pool recycling rings
- Intel (100G, ice, idpf):
- idpf: XDP and AF_XDP support preparations
- idpf: add flow steering
- add link_down_events statistic
- clean up the TSPLL code
- preparations for live VM migration
- nVidia/Mellanox:
- support zero-copy Rx/Tx interfaces (DMABUF and io_uring)
- optimize context memory usage for matchers
- expose serial numbers in devlink info
- support PCIe congestion metrics
- Meta (fbnic):
- add 25G, 50G, and 100G link modes to phylink
- support dumping FW logs
- Marvell/Cavium:
- support for CN20K generation of the Octeon chips
- Amazon:
- add HW clock (without timestamping, just hypervisor time access)
- Ethernet virtual:
- VirtIO net:
- support segmentation of UDP-tunnel-encapsulated packets
- Google (gve):
- support packet timestamping and clock synchronization
- Microsoft vNIC:
- add handler for device-originated servicing events
- allow dynamic MSI-X vector allocation
- support Tx bandwidth clamping
- Ethernet NICs consumer, and embedded:
- AMD:
- amd-xgbe: hardware timestamping and PTP clock support
- Broadcom integrated MACs (bcmgenet, bcmasp):
- use napi_complete_done() return value to support NAPI polling
- add support for re-starting auto-negotiation
- Broadcom switches (b53):
- support BCM5325 switches
- add bcm63xx EPHY power control
- Synopsys (stmmac):
- lots of code refactoring and cleanups
- TI:
- icssg-prueth: read firmware-names from device tree
- icssg: PRP offload support
- Microchip:
- lan78xx: convert to PHYLINK for improved PHY and MAC management
- ksz: add KSZ8463 switch support
- Intel:
- support similar queue priority scheme in multi-queue and
time-sensitive networking (taprio)
- support packet pre-emption in both
- RealTek (r8169):
- enable EEE at 5Gbps on RTL8126
- Airoha:
- add PPPoE offload support
- MDIO bus controller for Airoha AN7583
- Ethernet PHYs:
- support for the IPQ5018 internal GE PHY
- micrel KSZ9477 switch-integrated PHYs:
- add MDI/MDI-X control support
- add RX error counters
- add cable test support
- add Signal Quality Indicator (SQI) reporting
- dp83tg720: improve reset handling and reduce link recovery time
- support bcm54811 (and its MII-Lite interface type)
- air_en8811h: support resume/suspend
- support PHY counters for QCA807x and QCA808x
- support WoL for QCA807x
- CAN drivers:
- rcar_canfd: support for Transceiver Delay Compensation
- kvaser: report FW versions via devlink dev info
- WiFi:
- extended regulatory info support (6 GHz)
- add statistics and beacon monitor for Multi-Link Operation (MLO)
- support S1G aggregation, improve S1G support
- add Radio Measurement action fields
- support per-radio RTS threshold
- some work around how FIPS affects wifi, which was wrong (RC4 is used
by TKIP, not only WEP)
- improvements for unsolicited probe response handling
- WiFi drivers:
- RealTek (rtw88):
- IBSS mode for SDIO devices
- RealTek (rtw89):
- BT coexistence for MLO/WiFi7
- concurrent station + P2P support
- support for USB devices RTL8851BU/RTL8852BU
- Intel (iwlwifi):
- use embedded PNVM in (to be released) FW images to fix
compatibility issues
- many cleanups (unused FW APIs, PCIe code, WoWLAN)
- some FIPS interoperability
- MediaTek (mt76):
- firmware recovery improvements
- more MLO work
- Qualcomm/Atheros (ath12k):
- fix scan on multi-radio devices
- more EHT/Wi-Fi 7 features
- encapsulation/decapsulation offload
- Broadcom (brcm80211):
- support SDIO 43751 device
- Bluetooth:
- hci_event: add support for handling LE BIG Sync Lost event
- ISO: add socket option to report packet seqnum via CMSG
- ISO: support SCM_TIMESTAMPING for ISO TS
- Bluetooth drivers:
- intel_pcie: support Function Level Reset
- nxpuart: add support for 4M baudrate
- nxpuart: implement powerup sequence, reset, FW dump, and FW loading
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=lqbe
-----END PGP SIGNATURE-----
Merge tag 'net-next-6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core & protocols:
- Wrap datapath globals into net_aligned_data, to avoid false sharing
- Preserve MSG_ZEROCOPY in forwarding (e.g. out of a container)
- Add SO_INQ and SCM_INQ support to AF_UNIX
- Add SIOCINQ support to AF_VSOCK
- Add TCP_MAXSEG sockopt to MPTCP
- Add IPv6 force_forwarding sysctl to enable forwarding per interface
- Make TCP validation of whether packet fully fits in the receive
window and the rcv_buf more strict. With increased use of HW
aggregation a single "packet" can be multiple 100s of kB
- Add MSG_MORE flag to optimize large TCP transmissions via sockmap,
improves latency up to 33% for sockmap users
- Convert TCP send queue handling from tasklet to BH workque
- Improve BPF iteration over TCP sockets to see each socket exactly
once
- Remove obsolete and unused TCP RFC3517/RFC6675 loss recovery code
- Support enabling kernel threads for NAPI processing on per-NAPI
instance basis rather than a whole device. Fully stop the kernel
NAPI thread when threaded NAPI gets disabled. Previously thread
would stick around until ifdown due to tricky synchronization
- Allow multicast routing to take effect on locally-generated packets
- Add output interface argument for End.X in segment routing
- MCTP: add support for gateway routing, improve bind() handling
- Don't require rtnl_lock when fetching an IPv6 neighbor over Netlink
- Add a new neighbor flag ("extern_valid"), which cedes refresh
responsibilities to userspace. This is needed for EVPN multi-homing
where a neighbor entry for a multi-homed host needs to be synced
across all the VTEPs among which the host is multi-homed
- Support NUD_PERMANENT for proxy neighbor entries
- Add a new queuing discipline for IETF RFC9332 DualQ Coupled AQM
- Add sequence numbers to netconsole messages. Unregister
netconsole's console when all net targets are removed. Code
refactoring. Add a number of selftests
- Align IPSec inbound SA lookup to RFC 4301. Only SPI and protocol
should be used for an inbound SA lookup
- Support inspecting ref_tracker state via DebugFS
- Don't force bonding advertisement frames tx to ~333 ms boundaries.
Add broadcast_neighbor option to send ARP/ND on all bonded links
- Allow providing upcall pid for the 'execute' command in openvswitch
- Remove DCCP support from Netfilter's conntrack
- Disallow multiple packet duplications in the queuing layer
- Prevent use of deprecated iptables code on PREEMPT_RT
Driver API:
- Support RSS and hashing configuration over ethtool Netlink
- Add dedicated ethtool callbacks for getting and setting hashing
fields
- Add support for power budget evaluation strategy in PSE /
Power-over-Ethernet. Generate Netlink events for overcurrent etc
- Support DPLL phase offset monitoring across all device inputs.
Support providing clock reference and SYNC over separate DPLL
inputs
- Support traffic classes in devlink rate API for bandwidth
management
- Remove rtnl_lock dependency from UDP tunnel port configuration
Device drivers:
- Add a new Broadcom driver for 800G Ethernet (bnge)
- Add a standalone driver for Microchip ZL3073x DPLL
- Remove IBM's NETIUCV device driver
- Ethernet high-speed NICs:
- Broadcom (bnxt):
- support zero-copy Tx of DMABUF memory
- take page size into account for page pool recycling rings
- Intel (100G, ice, idpf):
- idpf: XDP and AF_XDP support preparations
- idpf: add flow steering
- add link_down_events statistic
- clean up the TSPLL code
- preparations for live VM migration
- nVidia/Mellanox:
- support zero-copy Rx/Tx interfaces (DMABUF and io_uring)
- optimize context memory usage for matchers
- expose serial numbers in devlink info
- support PCIe congestion metrics
- Meta (fbnic):
- add 25G, 50G, and 100G link modes to phylink
- support dumping FW logs
- Marvell/Cavium:
- support for CN20K generation of the Octeon chips
- Amazon:
- add HW clock (without timestamping, just hypervisor time access)
- Ethernet virtual:
- VirtIO net:
- support segmentation of UDP-tunnel-encapsulated packets
- Google (gve):
- support packet timestamping and clock synchronization
- Microsoft vNIC:
- add handler for device-originated servicing events
- allow dynamic MSI-X vector allocation
- support Tx bandwidth clamping
- Ethernet NICs consumer, and embedded:
- AMD:
- amd-xgbe: hardware timestamping and PTP clock support
- Broadcom integrated MACs (bcmgenet, bcmasp):
- use napi_complete_done() return value to support NAPI polling
- add support for re-starting auto-negotiation
- Broadcom switches (b53):
- support BCM5325 switches
- add bcm63xx EPHY power control
- Synopsys (stmmac):
- lots of code refactoring and cleanups
- TI:
- icssg-prueth: read firmware-names from device tree
- icssg: PRP offload support
- Microchip:
- lan78xx: convert to PHYLINK for improved PHY and MAC management
- ksz: add KSZ8463 switch support
- Intel:
- support similar queue priority scheme in multi-queue and
time-sensitive networking (taprio)
- support packet pre-emption in both
- RealTek (r8169):
- enable EEE at 5Gbps on RTL8126
- Airoha:
- add PPPoE offload support
- MDIO bus controller for Airoha AN7583
- Ethernet PHYs:
- support for the IPQ5018 internal GE PHY
- micrel KSZ9477 switch-integrated PHYs:
- add MDI/MDI-X control support
- add RX error counters
- add cable test support
- add Signal Quality Indicator (SQI) reporting
- dp83tg720: improve reset handling and reduce link recovery time
- support bcm54811 (and its MII-Lite interface type)
- air_en8811h: support resume/suspend
- support PHY counters for QCA807x and QCA808x
- support WoL for QCA807x
- CAN drivers:
- rcar_canfd: support for Transceiver Delay Compensation
- kvaser: report FW versions via devlink dev info
- WiFi:
- extended regulatory info support (6 GHz)
- add statistics and beacon monitor for Multi-Link Operation (MLO)
- support S1G aggregation, improve S1G support
- add Radio Measurement action fields
- support per-radio RTS threshold
- some work around how FIPS affects wifi, which was wrong (RC4 is
used by TKIP, not only WEP)
- improvements for unsolicited probe response handling
- WiFi drivers:
- RealTek (rtw88):
- IBSS mode for SDIO devices
- RealTek (rtw89):
- BT coexistence for MLO/WiFi7
- concurrent station + P2P support
- support for USB devices RTL8851BU/RTL8852BU
- Intel (iwlwifi):
- use embedded PNVM in (to be released) FW images to fix
compatibility issues
- many cleanups (unused FW APIs, PCIe code, WoWLAN)
- some FIPS interoperability
- MediaTek (mt76):
- firmware recovery improvements
- more MLO work
- Qualcomm/Atheros (ath12k):
- fix scan on multi-radio devices
- more EHT/Wi-Fi 7 features
- encapsulation/decapsulation offload
- Broadcom (brcm80211):
- support SDIO 43751 device
- Bluetooth:
- hci_event: add support for handling LE BIG Sync Lost event
- ISO: add socket option to report packet seqnum via CMSG
- ISO: support SCM_TIMESTAMPING for ISO TS
- Bluetooth drivers:
- intel_pcie: support Function Level Reset
- nxpuart: add support for 4M baudrate
- nxpuart: implement powerup sequence, reset, FW dump, and FW loading"
* tag 'net-next-6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1742 commits)
dpll: zl3073x: Fix build failure
selftests: bpf: fix legacy netfilter options
ipv6: annotate data-races around rt->fib6_nsiblings
ipv6: fix possible infinite loop in fib6_info_uses_dev()
ipv6: prevent infinite loop in rt6_nlmsg_size()
ipv6: add a retry logic in net6_rt_notify()
vrf: Drop existing dst reference in vrf_ip6_input_dst
net/sched: taprio: align entry index attr validation with mqprio
net: fsl_pq_mdio: use dev_err_probe
selftests: rtnetlink.sh: remove esp4_offload after test
vsock: remove unnecessary null check in vsock_getname()
igb: xsk: solve negative overflow of nb_pkts in zerocopy mode
stmmac: xsk: fix negative overflow of budget in zerocopy mode
dt-bindings: ieee802154: Convert at86rf230.txt yaml format
net: dsa: microchip: Disable PTP function of KSZ8463
net: dsa: microchip: Setup fiber ports for KSZ8463
net: dsa: microchip: Write switch MAC address differently for KSZ8463
net: dsa: microchip: Use different registers for KSZ8463
net: dsa: microchip: Add KSZ8463 switch support to KSZ DSA driver
dt-bindings: net: dsa: microchip: Add KSZ8463 switch support
...
The initial idea of making them const was correct as they were seperate
instances. When they got embedded into larger data structures, which are
even modified by the callback this got moot. The only reason why this went
unnoticed is that the required container_of() casts the const attribute
forcefully away.
Stop pretending that it is const.
-----BEGIN PGP SIGNATURE-----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=C0ua
-----END PGP SIGNATURE-----
Merge tag 'timers-cleanups-2025-07-27' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer cleanups from Thomas Gleixner:
"A treewide cleanup of struct cycle_counter const annotations.
The initial idea of making them const was correct as they were
seperate instances. When they got embedded into larger data
structures, which are even modified by the callback this got moot. The
only reason why this went unnoticed is that the required
container_of() casts the const attribute forcefully away.
Stop pretending that it is const"
* tag 'timers-cleanups-2025-07-27' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
time/timecounter: Fix the lie that struct cyclecounter is const
Merge in late fixes to prepare for the 6.17 net-next PR.
Conflicts:
net/core/neighbour.c
1bbb76a899 ("neighbour: Fix null-ptr-deref in neigh_flush_dev().")
13a936bb99 ("neighbour: Protect tbl->phash_buckets[] with a dedicated mutex.")
03dc03fa04 ("neighbor: Add NTF_EXT_VALIDATED flag for externally validated entries")
Adjacent changes:
drivers/net/usb/usbnet.c
0d9cfc9b8c ("net: usbnet: Avoid potential RCU stall on LINK_CHANGE event")
2c04d279e8 ("net: usb: Convert tasklet API to new bottom half workqueue mechanism")
net/ipv6/route.c
31d7d67ba1 ("ipv6: annotate data-races around rt->fib6_nsiblings")
1caf272972 ("ipv6: adopt dst_dev() helper")
3b3ccf9ed0 ("net: Remove unnecessary NULL check for lwtunnel_fill_encap()")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEn/sM2K9nqF/8FWzzDHRl3/mQkZwFAmiDqxUTHG1rbEBwZW5n
dXRyb25peC5kZQAKCRAMdGXf+ZCRnFSjB/0XHwODeVrpr22+xqYCNqjvoCZgZhtO
CY76JarRgSIbVdFbMlxoVpP96Aphdh4Fd+yD8myGRffqIWMwed8sy/wpR3O++Ly0
w+0U5X0NrQBT1GGeWM8Xg/N+/o10y1H5VFfx8Me+yRRQYLsfu6FMkWeACoZqMbDu
EzQeKkBkMVsWcjLGssnI6U6CUcudJETK5N1WeY+jOp8OgXQGT0AGdRb8DYN/XFZv
iBv5OMyPzET6PyA6Xu4vJ3vp450X2/6qlWQDIu88ht7IcCDIIbThdByQ4lgak0ux
iMETNCrZP1tryiR98HnJE6RNOVKvqkK/anvbI4bclZ5gGWNRu0BXWn+K
=RZuc
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-6.17-20250725' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2025-07-25
The first patch is by Khaled Elnaggar and converts the janz-ican3
driver's fwinfo_show() to sysfs_emit().
Vincent Mailhol contributes 3 patches that first fix a warning in the
ti_hecc driver and then add missing COMPILE_TEST more compile
coverage to the ti_hecc and tscan1 driver.
Randy Dunlap's patch let's the tscan1 driver depend on PC104.
A patch by Luis Felipe Hernandez fixes a kernel-doc error in the
ctucanfd driver.
Jimmy Assarsson contributes 10 patches for the kvaser_pciefd and 11
for the kvaser_usb driver. Both series simplify the identification of
physical the CAN interfaces and add devlink support to get information
about the running firmware.
* tag 'linux-can-next-for-6.17-20250725' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next: (27 commits)
Documentation: devlink: add devlink documentation for the kvaser_usb driver
can: kvaser_usb: Add devlink port support
can: kvaser_usb: Expose device information via devlink info_get()
can: kvaser_usb: Add devlink support
can: kvaser_usb: Store additional device information
can: kvaser_usb: Store the different firmware version components in a struct
can: kvaser_usb: Move comment regarding max_tx_urbs
can: kvaser_usb: Add intermediate variables
can: kvaser_usb: Assign netdev.dev_port based on device channel index
can: kvaser_usb: Add support for ethtool set_phys_id()
can: kvaser_usb: Add support to control CAN LEDs on device
Documentation: devlink: add devlink documentation for the kvaser_pciefd driver
can: kvaser_pciefd: Add devlink port support
can: kvaser_pciefd: Expose device firmware version via devlink info_get()
can: kvaser_pciefd: Add devlink support
can: kvaser_pciefd: Split driver into C-file and header-file.
can: kvaser_pciefd: Store device channel index
can: kvaser_pciefd: Store the different firmware version components in a struct
can: kvaser_pciefd: Add intermediate variable for device struct in probe()
can: kvaser_pciefd: Add support for ethtool set_phys_id()
...
====================
Link: https://patch.msgid.link/20250725161327.4165174-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Register each CAN channel of the device as an devlink physical port.
This makes it easier to get device information for a given network
interface (i.e. can2).
Example output:
$ devlink dev
usb/1-1.3:1.0
$ devlink port
usb/1-1.3:1.0/0: type eth netdev can0 flavour physical port 0 splittable false
usb/1-1.3:1.0/1: type eth netdev can1 flavour physical port 1 splittable false
$ devlink port show can1
usb/1-1.3:1.0/1: type eth netdev can1 flavour physical port 0 splittable false
$ devlink dev info
usb/1-1.3:1.0:
driver kvaser_usb
serial_number 1020
versions:
fixed:
board.rev 1
board.id 7330130009653
running:
fw 3.22.527
$ ethtool -i can1
driver: kvaser_usb
version: 6.12.10-arch1-1
firmware-version: 3.22.527
expansion-rom-version:
bus-info: 1-1.3:1.0
supports-statistics: no
supports-test: no
supports-eeprom-access: no
supports-register-dump: no
supports-priv-flags: no
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://patch.msgid.link/20250725123452.41-11-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Expose device information via devlink info_get():
* Serial number
* Firmware version
* Hardware revision
* EAN (product number)
Example output:
$ devlink dev
usb/1-1.2:1.0
$ devlink dev info
usb/1-1.2:1.0:
driver kvaser_usb
serial_number 1020
versions:
fixed:
board.rev 1
board.id 7330130009653
running:
fw 3.22.527
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://patch.msgid.link/20250725123452.41-10-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add devlink support at device level.
Example output:
$ devlink dev
usb/1-1.3:1.0
$ devlink dev info
usb/1-1.3:1.0:
driver kvaser_usb
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://patch.msgid.link/20250725123452.41-9-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Store additional device information; EAN (product number), serial_number
and hardware revision.
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://patch.msgid.link/20250725123452.41-8-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Store firmware version in kvaser_usb_fw_version struct, specifying the
different components of the version number.
And drop debug prinout of firmware version, since later patches will expose
it via the devlink interface.
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://patch.msgid.link/20250725123452.41-7-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Move comment regarding max_tx_urbs, to where the struct member is declared.
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://patch.msgid.link/20250725123452.41-6-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add intermediate variables, for readability and to simplify future patches.
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://patch.msgid.link/20250725123452.41-5-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Assign netdev.dev_port based on the device channel index, to indicate the
port number of the network device.
While this driver already uses netdev.dev_id for that purpose, dev_port is
more appropriate. However, retain dev_id to avoid potential regressions.
Fixes: 3e66d0138c ("can: populate netdev::dev_id for udev discrimination")
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://patch.msgid.link/20250725123452.41-4-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add support for ethtool set_phys_id(), to physically locate devices by
flashing a LED on the device.
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://patch.msgid.link/20250725123452.41-3-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add support to turn on/off CAN LEDs on device.
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://patch.msgid.link/20250725123452.41-2-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Register each CAN channel of the device as an devlink physical port.
This makes it easier to get device information for a given network
interface (i.e. can2).
Example output:
$ devlink dev
pci/0000:07:00.0
pci/0000:08:00.0
pci/0000:09:00.0
$ devlink port
pci/0000:07:00.0/0: type eth netdev can0 flavour physical port 0 splittable false
pci/0000:07:00.0/1: type eth netdev can1 flavour physical port 1 splittable false
pci/0000:07:00.0/2: type eth netdev can2 flavour physical port 2 splittable false
pci/0000:07:00.0/3: type eth netdev can3 flavour physical port 3 splittable false
pci/0000:08:00.0/0: type eth netdev can4 flavour physical port 0 splittable false
pci/0000:08:00.0/1: type eth netdev can5 flavour physical port 1 splittable false
pci/0000:09:00.0/0: type eth netdev can6 flavour physical port 0 splittable false
pci/0000:09:00.0/1: type eth netdev can7 flavour physical port 1 splittable false
pci/0000:09:00.0/2: type eth netdev can8 flavour physical port 2 splittable false
pci/0000:09:00.0/3: type eth netdev can9 flavour physical port 3 splittable false
$ devlink port show can2
pci/0000:07:00.0/2: type eth netdev can2 flavour physical port 2 splittable false
$ devlink dev info
pci/0000:07:00.0:
driver kvaser_pciefd
versions:
running:
fw 1.3.75
pci/0000:08:00.0:
driver kvaser_pciefd
versions:
running:
fw 2.4.29
pci/0000:09:00.0:
driver kvaser_pciefd
versions:
running:
fw 1.3.72
$ sudo ethtool -i can2
driver: kvaser_pciefd
version: 6.8.0-40-generic
firmware-version: 1.3.75
expansion-rom-version:
bus-info: 0000:07:00.0
supports-statistics: no
supports-test: no
supports-eeprom-access: no
supports-register-dump: no
supports-priv-flags: no
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://patch.msgid.link/20250725123230.8-10-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add devlink support at device level.
Example output:
$ devlink dev
pci/0000:07:00.0
pci/0000:08:00.0
pci/0000:09:00.0
$ devlink dev info
pci/0000:07:00.0:
driver kvaser_pciefd
pci/0000:08:00.0:
driver kvaser_pciefd
pci/0000:09:00.0:
driver kvaser_pciefd
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://patch.msgid.link/20250725123230.8-8-extja@kvaser.com
[mkl: kvaser_pciefd_remove(): fix use-after-free]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Split driver into C-file and header-file, to simplify future patches.
Move common definitions and declarations to a header file.
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://patch.msgid.link/20250725123230.8-7-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Store device channel index in netdev.dev_port.
Fixes: 26ad340e58 ("can: kvaser_pciefd: Add driver for Kvaser PCIEcan devices")
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://patch.msgid.link/20250725123230.8-6-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Store firmware version in kvaser_pciefd_fw_version struct, specifying the
different components of the version number.
And drop debug prinout of firmware version, since later patches will expose
it via the devlink interface.
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://patch.msgid.link/20250725123230.8-5-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add intermediate variable, for readability and to simplify future patches.
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://patch.msgid.link/20250725123230.8-4-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add support for ethtool set_phys_id(), to physically locate devices by
flashing a LED on the device.
Reviewed-by: Axel Forsman <axfo@kvaser.com>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://patch.msgid.link/20250725123230.8-3-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add support to turn on/off CAN LEDs on device.
Turn off all CAN LEDs in probe, since they are default on after a reset or
power on.
Reviewed-by: Axel Forsman <axfo@kvaser.com>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://patch.msgid.link/20250725123230.8-2-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Fix kernel-doc formatting issue causing unexpected indentation error
in ctucanfd driver documentation build. Convert main return values
to bullet list format while preserving numbered sub-list in order to
correct indentation error and visual structure in rendered html.
Signed-off-by: Luis Felipe Hernandez <luis.hernandez093@gmail.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Reviewed-by: Pavel Pisa <pisa@fel.cvut.cz>
Link: https://patch.msgid.link/20250722035352.21807-1-luis.hernandez093@gmail.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add a dependency on PC104 to limit (restrict) this driver kconfig
prompt to kernel configs that have PC104 set.
Add COMPILE_TEST as a possibility for more complete build coverage.
I tested this build config on x86_64 5 times without problems.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://patch.msgid.link/20250721002823.3548945-1-rdunlap@infradead.org
[mkl: fix conflict, remove Fixes: tag]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The latest firmware versions of USB CAN FD interfaces export the EP numbers
to be used to dialog with the device via the "type" field of a response to
a vendor request structure, particularly when its value is greater than or
equal to 2.
Correct the driver's test of this field.
Fixes: 4f23248246 ("can: peak_usb: include support for a new MCU")
Signed-off-by: Stephane Grosjean <stephane.grosjean@hms-networks.com>
Link: https://patch.msgid.link/20250724081550.11694-1-stephane.grosjean@free.fr
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
[mkl: rephrase commit message]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Andrei Lalaev reported a NULL pointer deref when a CAN device is
restarted from Bus Off and the driver does not implement the struct
can_priv::do_set_mode callback.
There are 2 code path that call struct can_priv::do_set_mode:
- directly by a manual restart from the user space, via
can_changelink()
- delayed automatic restart after bus off (deactivated by default)
To prevent the NULL pointer deference, refuse a manual restart or
configure the automatic restart delay in can_changelink() and report
the error via extack to user space.
As an additional safety measure let can_restart() return an error if
can_priv::do_set_mode is not set instead of dereferencing it
unchecked.
Reported-by: Andrei Lalaev <andrey.lalaev@gmail.com>
Closes: https://lore.kernel.org/all/20250714175520.307467-1-andrey.lalaev@gmail.com
Fixes: 39549eef35 ("can: CAN Network device driver and Netlink interface")
Link: https://patch.msgid.link/20250718-fix-nullptr-deref-do_set_mode-v1-1-0b520097bb96@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
ti_hecc depends on ARM. Add COMPILE_TEST to the dependency list so
that this driver can also be built on other platforms.
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://patch.msgid.link/20250715-can-compile-test-v2-2-f7fd566db86f@wanadoo.fr
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Fix below default (W=0) warning:
drivers/net/can/ti_hecc.c: In function 'ti_hecc_start':
drivers/net/can/ti_hecc.c:386:20: warning: conversion from 'long unsigned int' to 'u32' {aka 'unsigned int'} changes value from '18446744073709551599' to '4294967279' [-Woverflow]
386 | mbx_mask = ~BIT(HECC_RX_LAST_MBOX);
| ^
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://patch.msgid.link/20250715-can-compile-test-v2-1-f7fd566db86f@wanadoo.fr
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Fixes reset GPIO usage during probe by ensuring we retrieve the GPIO and
take the device out of reset (if it defaults to being in reset) before
we attempt to communicate with the device. This is achieved by moving
the call to tcan4x5x_get_gpios() before tcan4x5x_find_version() and
avoiding any device communication while getting the GPIOs. Once we
determine the version, we can then take the knowledge of which GPIOs we
obtained and use it to decide whether we need to disable the wake or
state pin functions within the device.
This change is necessary in a situation where the reset GPIO is pulled
high externally before the CPU takes control of it, meaning we need to
explicitly bring the device out of reset before we can start
communicating with it at all.
This also has the effect of fixing an issue where a reset of the device
would occur after having called tcan4x5x_disable_wake(), making the
original behavior not actually disable the wake. This patch should now
disable wake or state pin functions well after the reset occurs.
Signed-off-by: Brett Werling <brett.werling@garmin.com>
Link: https://patch.msgid.link/20250711141728.1826073-1-brett.werling@garmin.com
Cc: Markus Schneider-Pargmann <msp@baylibre.com>
Fixes: 142c6dc6d9 ("can: tcan4x5x: Add support for tcan4552/4553")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
As recommended in Documentation/filesystems/sysfs.rst, show() callbacks
should use sysfs_emit() or sysfs_emit_at() to format values returned to
userspace. Replace scnprintf() with sysfs_emit() in fwinfo_show().
Signed-off-by: Khaled Elnaggar <khaledelnaggarlinux@gmail.com>
Link: https://patch.msgid.link/20250712133609.331904-1-khaledelnaggarlinux@gmail.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEn/sM2K9nqF/8FWzzDHRl3/mQkZwFAmhw48wTHG1rbEBwZW5n
dXRyb25peC5kZQAKCRAMdGXf+ZCRnMWyCACNCHDSMr0BVzC2461MjsEmfi5P4Ri7
+9qL7oV5YWL3WDO8ltId0F8Up+WX8TeDIjzzx1z5tTZ1wgCSgoN74dIfkHRjaLzT
5u+D5880GrgtUUBsZCl6eY+uqazsMnZQHSDi69/KTaii8jW4YH+/mH5hgxoVUBAX
QHuMxcHQSn4lo8w31ChUVNVCFtUllZZRfdRzZX/JctFHLfUK17R04xyjzsWJDZm9
GxQwmu0Me7NFPipb1YzlDNu747XpTTnqBFNFjYJdzgkBgR7Ypy+yVng2h5j3PEy4
XGECdyfU9zmhP1ddn5k4J7H3OaWSsba5IwKwGU0zw5FHXFpfaxd7wcrb
=ELzu
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-6.17-20250711' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2025-07-11
The first patch is by Geert Uytterhoeven and converts the rcar_can
driver to DEFINE_SIMPLE_DEV_PM_OPS.
The last patch is by Biju Das and removes unused macros from the
rcar_canfd driver.
* tag 'linux-can-next-for-6.17-20250711' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next:
can: rcar_canfd: Drop unused macros
can: rcar_can: Convert to DEFINE_SIMPLE_DEV_PM_OPS()
====================
Link: https://patch.msgid.link/20250711101706.2822687-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cross-merge networking fixes after downstream PR (net-6.16-rc6-2).
No conflicts.
Adjacent changes:
drivers/net/wireless/mediatek/mt76/mt7925/mcu.c
c701574c54 ("wifi: mt76: mt7925: fix invalid array index in ssid assignment during hw scan")
b3a431fe2e ("wifi: mt76: mt7925: fix off by one in mt7925_mcu_hw_scan()")
drivers/net/wireless/mediatek/mt76/mt7996/mac.c
62da647a2b ("wifi: mt76: mt7996: Add MLO support to mt7996_tx_check_aggr()")
dc66a129ad ("wifi: mt76: add a wrapper for wcid access with validation")
drivers/net/wireless/mediatek/mt76/mt7996/main.c
3dd6f67c66 ("wifi: mt76: Move RCU section in mt7996_mcu_add_rate_ctrl()")
8989d8e90f ("wifi: mt76: mt7996: Do not set wcid.sta to 1 in mt7996_mac_sta_event()")
net/mac80211/cfg.c
58fcb1b428 ("wifi: mac80211: reject VHT opmode for unsupported channel widths")
037dc18ac3 ("wifi: mac80211: add support for storing station S1G capabilities")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Downgrade the "msg lost in rx" message to debug level, to prevent
flooding the kernel log with error messages.
Fixes: e0d1f4816f ("can: m_can: add Bosch M_CAN controller support")
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Link: https://patch.msgid.link/20250711-mcan_ratelimit-v3-1-7413e8e21b84@geanix.com
[mkl: enhance commit message]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Convert the Renesas R-Car CAN driver from SIMPLE_DEV_PM_OPS() to
DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr(). This lets us drop the
__maybe_unused annotations from its suspend and resume callbacks, and
reduces kernel size in case CONFIG_PM or CONFIG_PM_SLEEP is disabled.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/6ffe085f6e2548f53674dd11704b388cf4b303e9.1752086078.git.geert+renesas@glider.be
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In both the read callback for struct cyclecounter, and in struct
timecounter, struct cyclecounter is declared as a const pointer.
Unfortunatly, a number of users of this pointer treat it as a non-const
pointer as it is burried in a larger structure that is heavily modified by
the callback function when accessed. This lie had been hidden by the fact
that container_of() "casts away" a const attribute of a pointer without any
compiler warning happening at all.
Fix this all up by removing the const attribute in the needed places so
that everyone can see that the structure really isn't const, but can,
and is, modified by the users of it.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/2025070124-backyard-hurt-783a@gregkh
The rcar_canfd_f_*() inline functions to obtain channel-specific CAN-FD
register offsets really describe a memory layout. Hence replace them by
a C structure, to simplify the code, and reduce kernel size.
This also gets rid of warnings about unused rcar_canfd_f_*() inline
functions, which are reported by recent versions of clang.
Suggested-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Reported-by: Jakub Kicinski <kuba@kernel.org>
Closes: https://lore.kernel.org/20250618183827.5bebca8f@kernel.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://patch.msgid.link/292b75b3bc8dd95f805f0223f606737071c8cf86.1750327217.git.geert+renesas@glider.be
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEn/sM2K9nqF/8FWzzDHRl3/mQkZwFAmhSfcsTHG1rbEBwZW5n
dXRyb25peC5kZQAKCRAMdGXf+ZCRnDRmB/0WzxWVwV/xoCHiUeIy5y2j+veMhkC6
/sgHtiG0UQZ9ELliczM8//sODGUK34NTDIGV8sQ3Htr2S6WMncJKeGS2SNysRwLE
GxKphxizVfy8NxvHYU6TreAeyhcbJLsy+AhFnormPjBCgZOJZwN3x3quSdxRDDV/
/fNnlRK/06cikqToLxVqeZyrAchr0UJZ0JxLc8QseG0WFkX0286w3S/N/yp5rA1Y
GY1Y+EMo+zRWYRWNpkYM9lzcOURW8VyjXwzJeww/jot/sZs0tHzzx/9PmPU6s1t4
JAIRLgTDDa94GlbzXezc9fhTzqydpLxKroKhLX8wHyjqSUO41viuCG4L
=hU1D
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-6.17-20250618' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2025-06-18
All 10 patches are by Geert Uytterhoeven, target the rcar_canfd
driver, first cleanup/refactor the driver and then add support for
Transceiver Delay Compensation.
* tag 'linux-can-next-for-6.17-20250618' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next:
can: rcar_canfd: Add support for Transceiver Delay Compensation
can: rcar_canfd: Return early in rcar_canfd_set_bittiming() when not FD
can: rcar_canfd: Share config code in rcar_canfd_set_bittiming()
can: rcar_canfd: Rename rcar_canfd_setrnc() to rcar_canfd_set_rnc()
can: rcar_canfd: Repurpose f_dcfg base for other registers
can: rcar_canfd: Simplify data access in rcar_canfd_{ge,pu}t_data()
can: rcar_canfd: Add helper variable dev to rcar_canfd_reset_controller()
can: rcar_canfd: Add helper variable ndev to rcar_canfd_rx_pkt()
can: rcar_canfd: Remove bittiming debug prints
can: rcar_canfd: Consistently use ndev for net_device pointers
====================
Link: https://patch.msgid.link/20250618092336.2175168-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
struct gpio_chip now has callbacks for setting line values that return
an integer, allowing to indicate failures. Convert the driver to using
them.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Reviewed-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://patch.msgid.link/20250616-gpiochip-set-rv-net-v2-4-cae0b182a552@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add an integer return value to mcp251x_write_bits() and use it to
propagate the one returned by mcp251x_spi_write(). Return that value on
error in the request() GPIO callback.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Reviewed-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://patch.msgid.link/20250616-gpiochip-set-rv-net-v2-3-cae0b182a552@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fixes the power regulator retrieval in tcan4x5x_can_probe() by ensuring
the regulator pointer is not set to NULL in the successful return from
devm_regulator_get_optional().
Fixes: 3814ca3a10 ("can: tcan4x5x: tcan4x5x_can_probe(): turn on the power before parsing the config")
Signed-off-by: Brett Werling <brett.werling@garmin.com>
Link: https://patch.msgid.link/20250612191825.3646364-1-brett.werling@garmin.com
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The Renesas CAN-FD hardware block supports configuring Transceiver Delay
Compensation, and reading back the Transceiver Delay Compensation
Result, which is needed to support high transfer rates like 8 Mbps.
The Secondary Sample Point is either the measured delay plus the
configured offset, or just the configured offset.
Fix the existing RCANFD_FDCFG_TDCO() macro for the intended use case
(writing instead of reading the field). Add register definition bits
for the Channel n CAN-FD Status Register.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://patch.msgid.link/69db727d5f728d679ba691d20854e7d963d0f323.1749655315.git.geert+renesas@glider.be
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Return early after completing all setup for non-FD mode in
rcar_canfd_set_bittiming(), to prepare for the advent of more FD-only
setup.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://patch.msgid.link/35fcdcad026cfdd0fd361637f065842d99a6c19d.1749655315.git.geert+renesas@glider.be
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The configuration register format for nominal bit timings in CAN-FD mode
and the format for bit timings in CAN mode on CAN-FD controllers with
shared Classical CAN registers are the same.
Restructure the code to make this clear, also reducing kernel size by 80
bytes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://patch.msgid.link/b7643a3c49777989d02145a85b85cf773ec2123f.1749655315.git.geert+renesas@glider.be
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
