Introduce frr-ripngd.yang, which defines a model for managing the
FRR ripngd daemon.
Update the 'frr_yang_module_info' array of ripngd with the new
'frr-ripngd' module.
Add two new files (ripng_cli.[ch]) which should contain all ripngd
commands converted to the new northbound model. Centralizing all
commands in a single place will facilitate the process of moving
the CLI to a separate program in the future.
Add automatically generated stub callbacks in
ripng_northbound.c. These callbacks will be implemented gradually
in the following commits.
Add the confd.frr-ripngd.yang YANG module with annotations specific
to the ConfD daemon.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
This reverts commit 48944eb65e.
We're using GNU C, not ISO C - and this commit triggers new (real)
warnings about {0} instead of bogus ones about {}.
Signed-off-by: David Lamparter <equinox@diac24.net>
We sometimes store ifindex information in the NEXTHOP_TYPE_IPV[4|6]
so let's let us display that information as well when dumping
a nexthop.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
There are cases where the passed parameter for a vty command is either
an interface name or an ip address. Because the interface name can be a
number, and because the user may want to use a number to define an IP (
for instance 'ping 0' is valid from shell purpose), there is a choice
that needs to be done at frr level. either from the application point of
view, the interface name will be priorized, or each number will be
considered as an ip address. In that commit, the inet_aton procedure is
replaced with the inet_pton procedure that ignores ips with just a
number.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
The northbound infrastructure for operational data was subpar compared
to the infrastructure for configuration data. This commit addresses most
of the existing problems, making it possible to write operational-data
callbacks for more complex YANG models.
Summary of the changes:
* Add support for nested YANG lists.
* Add support for leaf-lists.
* Add support for leafs of type "empty".
* Introduce the "show yang operational-data XPATH" command, and write an
unit test for it. The main purpose of this command is to make it
easier to test the operational-data northbound callbacks.
* Introduce the nb_oper_data_iterate() function, that can be used
to iterate over operational data. Make the CLI and sysrepo use this
function.
* Since ConfD has a very peculiar API, it can't reuse the
nb_oper_data_iterate() like the other northbound clients. In this
case, adapt the existing ConfD callbacks to support the new features
(and make some performance improvements in the process).
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Prevent the confd plugin from subscribing to configuration changes on a
data tree that contains only state data.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
A YANG list that contains both configuration and state data must have
the following callbacks: create(), delete(), get_next(), get_keys()
and lookup_entry().
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
* Rename yang_snodes_iterate() to yang_snodes_iterate_subtree() and
expose it in the public API.
* Rename yang_module_snodes_iterate() to yang_snodes_iterate_module().
* Rename yang_all_snodes_iterate() to yang_snodes_iterate_all().
* Make it possible to stop the iteration at any time by returning
YANG_ITER_STOP in the iteration callbacks.
* Make the iteration callbacks accept only one user argument and not
two.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
In some cases it will be necessary to load all FRR native modules.
Examples:
* vtysh needs to load all YANG modules so that it can manipulate data
from all daemons.
* The gen_northbound_callbacks tool will need to load all YANG modules
since augmentations from one module can have an effect in the required
northbound callbacks of other modules.
The new yang_module_load_all() function provides this functionality.
As a side note, the "frr_native_modules" will need to be updated every
time we add a new YANG module to FRR.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
For convenience, make yang_dnode_free() remove the entire data tree and
not only the data node given as a parameter.
Also, add a null-pointer check on nb_config_replace() before calling
yang_dnode_free().
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
By default the data nodes created by yang_dnode_new() could contain
only configuration data (LYD_OPT_CONFIG). Add a 'config_only' option
to yang_dnode_new() so that it can create data nodes containing both
configuration and state data.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Prefetching the schema node when creating yang_data structures is
expensive, and in most cases we don't need that information. In that case,
fetch the schema information only when necessary to improve performance
when fetching operational data.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
A while ago all FRR configuration commands were converted to use the
QOBJ infrastructure to keep track of configuration objects. This
means the configuration lock isn't necessary anymore because the
QOBJ code detects when someones tries to edit a configuration object
that was deleted and react accordingly (log an error and abort the
command). The possibility of accessing dangling pointers doesn't
exist anymore since vty->index was removed.
Summary of the changes:
* remove the configuration lock and the vty_config_lockless() function.
* rename vty_config_unlock() to vty_config_exit() since we need to
clean up a few things when exiting from the configuration mode.
* rename vty_config_lock() to vty_config_enter() to remove code
duplication that existed between the three different "configuration"
commands (terminal, private and exclusive).
Configuration commands converted to the new northbound model don't
need the configuration lock either since the northbound API also
detects when someone tries to edit a configuration object that
doesn't exist anymore.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
When editing the candidate configuration, the northbound must ensure
that either all changes made by a command are accepted or none are.
This is done to prevent inconsistent states where only parts of a
command are applied in the event any error happens.
The previous API for converted commands, the nb_cli_cfg_change()
function, required callers to pass an array containing all changes
that needed to be applied in the candidate configuration. The
problem with this API is that it was very inconvenient for complex
commands, which change different configuration options depending
on several factors. This required users to manipulate the array
of configuration changes using low-level primitives, making it
complicated to implement some commands.
To solve this problem, introduce a new API based on the two following
functions:
- nb_cli_enqueue_change()
- nb_cli_apply_changes()
The first function is used to enqueue configuration changes, one
at time. Then the nb_cli_apply_changes() function is used to apply
all the enqueued configuration changes.
To implement this, a static-sized array was allocated in the "vty"
structure, along with a counter of enqueued changes. This eliminates
the need to declare an array of configuration changes in every
converted CLI command, simplifying things quite considerably.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Add the "abort_if_not_found" parameter to the yang_dnode_get_entry()
function instead of always aborting when an user pointer is not
found. This will make it possible, for example, to use this function
during the validation phase of a configuration transaction. Callers
will only need to check if the function returned NULL or not,
since new configuration objects (if any) won't be created until
the NB_EV_APPLY phase of the transaction.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
In some cases it might be desirable to obtain the schema name of
a libyang data node. Introduce the yang_dnode_get_schema_name()
function for this purpose.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
This fixes an infinite loop that happened every time the connection
to the confd daemon was lost. Deactivate the confd module when
that happens to fix the infinite loop. This is only a temporary
workaround, in the long term we need to add a connection retry timer
to reestablish the connection to the confd daemon once it's back.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
the netns discovery process executed when vrf backend is netns, allows
the zebra daemon to dynamically change the default vrf name value. This
option is disabled, when the zebra is forced to a default vrf value with
option -o.
PR=61513
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
This bakes our YANG models straight into the library/daemons, so they
don't need to be loaded from /usr/share/yang. This makes the
installation quite a bit more robust, as well as gets us halfway to
running uninstalled. (The other half is baking in the extension type
module.)
The /usr/share/yang directory is still searched as a fallback, as well
as for the experimental YANG model translator. This is likely to stay
as is for the time being.
Signed-off-by: David Lamparter <equinox@diac24.net>
Display following Per MAC and Neigh's output:
If duplicate address detection is under process,
display detection start time and detection count.
If duplicate address detection detected an address
as duplicate, display detection time and duplicate
status.
Signed-off-by: Chirag Shah <chirag@cumulusnetworks.com>
Duplicate address detection configuration clis
under bgp l2vpn evpn config mode.
- Enabled/Disable (global knob) for feature.
- Configure cli for duplicate detection action
freeze and freze until time (auto-recovery).
Signed-off-by: Chirag Shah <chirag@cumulusnetworks.com>
if zebra is not started, then vrf identifiers are not available. This
prevents import/exportation to be available. This commit permits having
import/export available, even when zebra is not started.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
This commit introduces lib/id_alloc, which has facilities for both an ID number
allocator, and less efficient ID holding pools. The pools are meant to be a
temporary holding area for ID numbers meant to be re-used, and are implemented
as a linked-list stack.
The allocator itself is much more efficient with memory. Based on sizeof
values on my 64 bit desktop, the allocator requires around 155 KiB per
million IDs tracked.
IDs are ultimately tracked in a bit-map split into many "pages." The
allocator tracks a list of pages that have free bits, and which sections
of each page have free IDs, so there isn't any scanning required to find
a free ID. (The library utility ffs, or "Find First Set," is generally a
single CPU instruction.) At the moment, totally empty pages will not be
freed, so the memory utilization of this allocator will remain at the
high water mark.
The initial intended use case is for BGP's TX Addpath IDs to be pulled
from an allocator that tracks which IDs are in use, rather than a free
running counter. The allocator reserves ID #0 as a sentinel value for
an invalid ID numbers, and BGP will want ID #1 reserved as well. To
support this, the allocator allows for IDs to be explicitly reserved,
though be aware this is only practical to use with low numbered IDs
because the allocator must allocate pages in order.
Signed-off-by Mitchell Skiba <mskiba@amazon.com>
ipv6 distribute-list name picked up was not the correct one. the
parameter number is modified accordingly.
Also, the unconfiguration of distribute-list ipv6 was conflicting with
other daemon, thus making impossible the unconfigration. The command has
been split to be specific to ipv6 distribute-list.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
This duplicates itself N times since it's not wrappered in a vtysh
command. In lieu of doing that, just remove the message, it's not really
necessary.
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
It's been a year since we added the new optional parameters
to instantiation. Let's switch over to the new name.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
The frr-interface YANG module models interfaces using a YANG list keyed
by the interface name and the interface VRF. Interfaces can't be keyed
only by their name since interface names might not be globally unique
when the netns VRF backend is in use. When using the VRF-Lite backend,
however, interface names *must* be globally unique. In this case, we need
to validate the uniqueness of interface names inside the appropriate
northbound callback since this constraint can't be expressed in the
YANG language. We must also ensure that only inactive interfaces can be
removed, among other things we need to validate in the northbound layer.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Introduce frr-interface.yang, which defines a model for managing FRR
interfaces.
Update the 'frr_yang_module_info' array of all daemons that will
implement this module.
Add automatically generated stub callbacks in if.c. These callbacks will
be implemented in the following commit.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
This plugin leverages the northbound API to integrate FRR with Sysrepo,
a YANG-based configuration and operational state data store.
The plugin is linked to the libsysrepo library and communicates with
the sysrepod daemon using GPB (Google Protocol Buffers) over AF_UNIX
sockets. The integration consists mostly of glue code that calls the
appropriate FRR northbound callbacks in response to events triggered
by the sysrepod daemon (e.g. request to change the configuration or to
fetch operational data).
To build the sysrepo plugin, provide the --enable-sysrepo option to the
configure script while building FRR (the libsysrepo library needs to be
installed in the system).
When installed, the sysrepo plugin will be available for all FRR daemons
and can be loaded using the -M (or --module) command line option.
Example: bgpd -M sysrepo.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
This plugin leverages the northbound API to integrate FRR with the ConfD
management agent.
The plugin is linked to the libconfd library and communicates with the
confd daemon using local TCP sockets. The integration consists mostly
of glue code that calls the appropriate FRR northbound callbacks in
response to events triggered by the confd daemon (e.g. request to change
the configuration or to fetch operational data).
By integrating FRR with the libconfd library, FRR can be managed using
all northbound interfaces provided by ConfD, including NETCONF, RESTCONF
and their Web API.
The ConfD CDB API is used to handle configuration changes and the ConfD
Data Provider API is used to provide operational data, process RPCs and
send notifications. Support for configuration management using the ConfD
Data Provider API is not available at this point.
The ConfD optional 'get_object()' and 'get_next_object()' callbacks were
implemented for optimal performance when fetching operational data.
This plugins requires ConfD 6.5 or later since it uses the new leaf-list
API introduced in ConfD 6.5.
To install the plugin, the --enable-confd option should be given to the
configure script, specifying the location where ConfD is installed.
Example: ./configure --enable-confd=/root/confd-6.6
When installed, the confd plugin will be available for all FRR daemons
and can be loaded using the -M (or --module) command line option.
Example: zebra -M confd.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
* Cast when assigning should be to uint16_t
* Restored comment documenting strange behavior
* Further increased PREFIX_STRLEN to 80 chars
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
The CMD_SUCCESS_DAEMON case should be excluded from storing the command line
that we think failed.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
We weren't cleaning up some files (a whole lot of python foobar) and had
some files in the dist tarball that don't quite belong there.
Signed-off-by: David Lamparter <equinox@diac24.net>
The ->hash_cmp and linked list ->cmp functions were sometimes
being used interchangeably and this really is not a good
thing. So let's modify the hash_cmp function pointer to return
a boolean and convert everything to use the new syntax.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
libunwind provides an alternate to backtrace() for printing out the call
stack of a particular location. It doesn't use the frame pointer, it
goes by the DWARF debug info. In most cases the traces have exactly the
same information, but there are some situations where libunwind traces
are better.
(On some platforms, the libc backtrace() also uses the DWARF debug info
[e.g.: ARM backtraces are impossible without it] but this is not the
case everywhere, especially not on BSD libexecinfo.)
Signed-off-by: David Lamparter <equinox@diac24.net>
Allow the modification of whether or not we will allow
BUM flooding on the vxlan bridge. To do this allow
the upper level protocol to specify via the ZEBRA_VXLAN_FLOOD_CONTROL
zapi message.
If flooding is disabled then BUM traffic will not be forwarded
to other VTEP's.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
When reading in config files and we have failures on multiple
lines actually note the actual failure lines and return them.
This fixes an issue where we stopped counting errors after
the first one and we got missleading line numbers that
did not correspond to the actual problem.
This is fixed:
sharpd@donna ~/frr> sudo /usr/lib/frr/pimd --log=stdout -A 127.0.0.1 -f /etc/frr/pimd.conf
2018/10/11 09:41:01 PIM: VRF Created: default(0)
2018/10/11 09:41:01 PIM: pim_vrf_enable: for default
2018/10/11 09:41:01 PIM: zclient_lookup_sched_now: zclient lookup immediate connection scheduled
2018/10/11 09:41:01 PIM: zclient_lookup_new: zclient lookup socket initialized
2018/10/11 09:41:01 PIM: pimd 6.1-dev starting: vty@2611
2018/10/11 09:41:01 PIM: [EC 100663304] ERROR: No such command on config line 2: inteface lo
2018/10/11 09:41:01 PIM: [EC 100663304] ERROR: No such command on config line 3: ip igmp
2018/10/11 09:41:01 PIM: [EC 100663304] ERROR: No such command on config line 4: ip igmp join 224.1.1.1 13.13.13.2
^C2018/10/11 09:45:09 PIM: Terminating on signal SIGINT
2018/10/11 09:45:09 PIM: VRF Deletion: default(0)
Fixes: #3161
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Don't allocate threads in the stack, but use the standardized
`thread_get` and `thread_add_unused` to avoid creating corner cases in
the thread API.
This fixes a thread mutex memory leak in FreeBSD.
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
Two important changes:
* Centralize the thread teardown procedure;
* Save and restore thread mutex context to avoid losing the memory
pointer;
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
The compiler.h header provides us with some useful macro's
that we are using in the system. We do not know exactly
where the CPP_NOTICE and CPP_WARN macros are used but
they can move around. Place this header early in the
build then.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
This cleans up watchfrr to be more "normal" like the other daemons in
terms of what it does in main(), i.e. using the full frr_*() call set.
Also, this changes the startup behaviour on watchfrr to stay attached on
the daemon's parent process until startup is really complete. This
should allow removing the "watchfrr.started" hack at some point.
Signed-off-by: David Lamparter <equinox@diac24.net>
This makes libfrr.so executable to print its version info. This is
useful if you need to check your libfrr.so matches your daemons.
Signed-off-by: David Lamparter <equinox@diac24.net>
This option can be used to get statically linked binaries.
Note: libfrr.la is removed from modules' library dependency list. This
is intentional and explained in a comment in lib/subdir.am.
Signed-off-by: David Lamparter <equinox@diac24.net>
Overview:
Coverity points a copy-paste error in the Red-Black tree implementation. The
RB tree code is based on the OpenBSD implementation, so at first glance, it
is a strong point for thinking twice before touching anything.
Details:
The code is an augmented RB tree implementation [1], which adds to RB trees
the possibility of using a callback on every node update for updating per-node
associated metainformation. The bug is clear once checking other places where
the callback is called.
Impact:
- FRR: no impact, because the "augmented" capability is not being used.
- OpenBSD [2]: it seems there is no impact, at least in the 'src' repository.
Additional observations:
- If the "augmented" capability is not used, the code could run faster (at
every operation on a node the callback is checked for not being NULL). May
be branch prediction could be enough for those extra operations being
negligible on most processors in use.
[1] http://kaba.hilvi.org/pastel-1.3.0/pastel/sys/redblacktree.htm
[2] GH mirror: https://github.com/openbsd/src/blob/master/sys/kern/subr_tree.c
Signed-off-by: F. Aragon <paco@voltanet.io>
Keep track of how often route-maps are applied and
how often each clause of a route-map is applied.
This change showed that `show route-map` was outputting
odd data so fix that output and add in the applied
times too.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Wrapper the get/set of the table->info pointer so that
people are not directly accessing this data.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
When entering a interface name and you fat-finger it
actually display some useful information about the vrf
we are in.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
When the "call" CLI is executed from with-in a route-map that is already in use,
there is a need to get the route-map clients to re-evalute the clauses defined
by both the parent route-map, as well as the child route-map.
The existing callbacks, add_hook() and delete_hook() can be used by the lib to
inform the clients when the "call" is configured and unconfigured.
Signed-off-by: NaveenThanikachalam <nthanikachal@vmware.com>
Redundant parentheses surrounding declarator removed.
Can be detected via static analysis with e.g.
./configure CFLAGS=-Wredundant-parens CC=clang
Signed-off-by: F. Aragon <paco@voltanet.io>
OS-level yield is generally a bad and possibly dangerous idea. If the
thread should be suspended, there should always be something to wait on,
or it turns into busy waiting. And if it's "just giving something else
the chance to run" - that's the kernel's job to determine, and the
kernel will do so while considering priorities, cgroups, and whatnot.
Let it do its job.
Signed-off-by: David Lamparter <equinox@diac24.net>
All I can see is an unneccessary complication. If there's some purpose
here it needs to be documented...
Signed-off-by: David Lamparter <equinox@diac24.net>
Corrections so that the BGP daemon can work with the label manager properly
through a label-manager proxy. Details:
- Correction so the BGP daemon behind a proxy label manager gets the range
correctly (-I added to the BGP daemon, to set the daemon instance id)
- For the BGP case, added an asynchronous label manager connect command so
the labels get recycled in case of a BGP daemon reconnection. With this,
BGPd and LDPd would behave similarly.
Signed-off-by: F. Aragon <paco@voltanet.io>
Allow at timer wheel creation time the ability to specify a
name for what we want the 'show thread cpu' to show up as.
Modify pim to note this.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Allow the user to specify a run name for display in
'show thread cpu' that is different than the function
name we are calling.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
FreeBSD supports pthread_set_name_np() too. Also, pthread_set_name_np()
returns void. And NetBSD has pthread_setname_np() with an extra arg...
Signed-off-by: David Lamparter <equinox@diac24.net>
Need this to get CMSG_SPACE/CMSG_LEN on Solaris.
Also, AC_GNU_SOURCE is deprecated, AC_USE_SYSTEM_EXTENSIONS does that.
Signed-off-by: David Lamparter <equinox@diac24.net>
config.h (or, transitively, zebra.h) must be the first include file
listed for autoconf things like _GNU_SOURCE and _POSIX_C_SOURCE to work
correctly.
Signed-off-by: David Lamparter <equinox@diac24.net>
ASAN/MSAN/TSAN flags need to be in CFLAGS and LDFLAGS; the latter links
the correct compiler-dependent library. Also, the configure switch was
broken (--disable-... would enable the sanitizer.)
Signed-off-by: David Lamparter <equinox@diac24.net>
Since we're now building through one large Makefile, we can easily put
things with their daemons and crossreference nicely.
Signed-off-by: David Lamparter <equinox@diac24.net>
Clang was thinking the random level could be negative. (And, no, I
couldn't figure that out by reading its output... trial and error this
was.)
Signed-off-by: David Lamparter <equinox@diac24.net>
Add a TAILQ_POP_FIRST so Clang understands it's the same item that is
getting removed from the list.
Signed-off-by: David Lamparter <equinox@diac24.net>
Auto-detect if pthread_condattr_setclock is available and if
it is not allow the code to compile around the issue.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
The vty_prefix_list_install function was modifying the prefix to match the
specified prefix length and warning in the log file. Modify
code to use zlog_info as that a warn implies that something has
gone terribly wrong. Additionally display to the terminal as
well so that user can get immediate feedback from something
that they can correct.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Solution :
The following procedures would be performed :
1. Verify if the pid file for each daemon is present or not. If the file is not present, that means the
daemon is getting instantiated for the first time. So let it go ahead.
If the file is present proceed to point ‘2’.
2. Try fetching the properties of the pid file.
3. If it has RW lock, that means one instance of this the daemon is already running.
So stop moving ahead and do exit() else let it go ahead. Please note all above procedure happen at
the initial state of daemon’s instantiation, much before it starts any session with other
process/allocates resources etc.. and this verification do not have any impact of any
operations done later, if the verification succeeds.
Signed-off-by: bisdhdh sadhub@vmware.com
For OpenFabric operation, we need to be able to install routes via
interfaces without any IPv4 addresses configured. Introduce a flag
ZEBRA_FLAG_ONLINK which upper protocols can set on a route they send
towards zebra, to force the nexthops to be considered onlink.
Signed-off-by: Christian Franke <chris@opensourcerouting.org>
fabricd is built using the sources of isisd. To allow differentiation
in the code, -DFABRICD=1 is added to its preprocessor flags.
Signed-off-by: Christian Franke <chris@opensourcerouting.org>
The ZEBRA_IPV4_ROUTE_IPV6_NEXTHOP_ADD zapi message has no creators and
no handlers. Let's just remove.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Move the aggregate pointer from the route_node into agg_node
so that people using struct route_node will see a savings
in data size.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Add a abstraction for `struct route_node` and `struct route_table`
such that we can have an aggregate route_node and table. This
is because only bgp/rfapi and ripng use the aggregate data pointer
in `struct route_node`. For full route tables other routing
protocols and tables are paying a 8 byte overhead per node.
A full bgp table ends up being ~1.2 million routes in bgp
and zebra. This is not an insiginificant amount of data.
So create the data structures for this replacement, but
do not replace the aggregate pointer yet. This is because
later commits will convert rfapi and ripng over to this
new data, and finally we'll move the aggregate pointer.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Fix CLANG warning:
Report for if.c | 2 issues
===============================================
< WARNING: else is not generally useful after a break or return
< #390: FILE: /tmp/f1-28557/if.c:390:
Signed-off-by: Thibaut Collet <thibaut.collet@6wind.com>
Problem reported that some bgp and ospf json commands did not return
any json output at all if the bgp/ospf instance did not exist.
Additionally, some bgp and ospf json commands did not return any json
output if the instance existed but no neighbors were defined. This
fix makes these commands more consistent in returning empty braces for
json output and issue a message if not using json output. Additionally,
made the flag "use_json" a bool to make it consistent since previously,
it had been defined as an int, char, u_char, and bool at various places.
Ticket: CM-21040
Signed-off-by: Don Slice <dslice@cumulusnetworks.com>
This crash occurs only with netns implementation.
vrf meaning is different regarging its implementation (netns or
vrf-lite)
- With vrf-lite implementation vrf is a property of the interface that
can be changed as the speed or the state (iproute2 command: "ip link
set dev IF_NAME master VRF_NAME"). All interfaces of the system are in
the same netns and so interface name is unique.
- With netns implementation vrf is a characteristic of the interface
that CANNOT be changed: it is the id of the netns where the interface
is located. To change the vrf of an interface (iproute2 command to
move an interface "ip netns exec VRF_NAME1 ip link set dev IF_NAME
netns VRF_NAME2") the interface is deleted from the old vrf and
created in the new vrf.
Interface name is not unique, the same name can be present in the
different netns (typically the lo interface) and search of interface
must be done by the tuple (interface name, netns id).
Current tests on the vrf implementation (vrf-lite or netns) are not
sufficient. In some cases (for example when an interface is moved from
a vrf X to the default vrf and then move back to VRF X) we can have a
corruption message and then a crash of zebra.
To avoid this corruption test on the vrf implementation, needed when an
interface changes, has been rewritten:
- For all interface changes except deletion the if_get_by_name function,
that checks if an interface exists and creates or updates it if
needed, is changed:
* The vrf-lite implementation is unchanged: search of the interface
is based only on the name and update the vrf-id if needed.
* The netns implementation search of the interface is based on the
(name, vrf-id) tuple and interface is created if not found, the
vrf-id is never updated.
- deletion of an interface (reception of a RTM_DELLINK netlink message):
* The vrf-lite implementation is unchanged: the interface
information are cleared and the interface is moved to the default
vrf if it does not belong to (to allow vrf deletion)
* The netns implementation is changed: only the interface
information are cleared and the interface stays in its vrf to
avoid conflict with interface with the same name in the default
vrf.
This implementation reverts (partially or totally):
commit 393ec5424e ("zebra: fix missing node attribute set in ifp")
commit e9e9b1150f ("lib: create interface even if name is the same")
commit 9373219c67 ("zebra: improve logs when replacing interface to an
other netns")
Fixes: b53686c52a ("zebra: delete interface that disappeared")
Signed-off-by: Thibaut Collet <thibaut.collet@6wind.com>
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
To correct potential crash with netns implementation of vrf (see next
commit) it is necessary to allow any daemons to know the vrf
implementation whatever the vrf.
With current implementation the daemons do not know the vrf
implementation for the default vrf. For this vrf the returned vrf
implementation is always vrf-lite.
To solve this issue a netns name is set to the default vrf to just test
is presence to know the used implementation.
For zebra a netns name (if needed) is set in the vrf_init function just
before enabling the vrf. So this information is propagated to the other
daemons thanks the zapi message called when the vrf is enable at zebra
layer and override the default configuration (vrf-lite) of the daemon.
Signed-off-by: Thibaut Collet <thibaut.collet@6wind.com>
Sphinx actually does work with a parallel build, if the doctree creation
is a separate step (which the other builds will then just read
unmodified.) This can be done with the "dummy" target.
This also adds "-j6" to sphinx-build and adds a "--disable-doc-html"
switch on ./configure to turn on/off building HTML docs separately.
Also, HTML docs are now installed by "make install" to
/usr/share/doc/frr/html.
Signed-off-by: David Lamparter <equinox@diac24.net>
stdatomic.h does not have aliases for all of the useful gcc
atomic primitives; add them in for that path through
frratomic.h.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
