In MLO configuration, ath12k_mac_radio_start() iterates through all
the radios and makes the ar state 'ON'. Even though some bands are
not supported in certain countries, ath12k_reg_update_chan_list()
tries to update the channel list for all the active pdevs and ends
up in the warn_on for non-supported band.
To prevent this, disable the pdev when the number of channels across
all bands supported by the pdev is zero for a particular country.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthik M <quic_karm@quicinc.com>
Signed-off-by: Muna Sinada <muna.sinada@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250506214930.3561348-1-muna.sinada@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
During beacon miss handling, ath12k driver iterates over active virtual
interfaces (vifs) and attempts to access the radio object (ar) via
arvif->deflink->ar.
However, after commit aa80f12f3b ("wifi: ath12k: defer vdev creation for
MLO"), arvif is linked to a radio only after vdev creation, typically when
a channel is assigned or a scan is requested.
For P2P capable devices, a default P2P interface is created by
wpa_supplicant along with regular station interfaces, these serve as dummy
interfaces for P2P-capable stations, lack an associated netdev and initiate
frequent scans to discover neighbor p2p devices. When a scan is initiated
on such P2P vifs, driver selects destination radio (ar) based on scan
frequency, creates a scan vdev, and attaches arvif to the radio. Once the
scan completes or is aborted, the scan vdev is deleted, detaching arvif
from the radio and leaving arvif->ar uninitialized.
While handling beacon miss for station interfaces, P2P interface is also
encountered in the vif iteration and ath12k_mac_handle_beacon_miss_iter()
tries to dereference the uninitialized arvif->deflink->ar.
Fix this by verifying that vdev is created for the arvif before accessing
its ar during beacon miss handling and similar vif iterator callbacks.
==========================================================================
wlp6s0: detected beacon loss from AP (missed 7 beacons) - probing
KASAN: null-ptr-deref in range [0x0000000000000010-0x0000000000000017]
CPU: 5 UID: 0 PID: 0 Comm: swapper/5 Not tainted 6.16.0-rc1-wt-ath+ #2 PREEMPT(full)
RIP: 0010:ath12k_mac_handle_beacon_miss_iter+0xb5/0x1a0 [ath12k]
Call Trace:
__iterate_interfaces+0x11a/0x410 [mac80211]
ieee80211_iterate_active_interfaces_atomic+0x61/0x140 [mac80211]
ath12k_mac_handle_beacon_miss+0xa1/0xf0 [ath12k]
ath12k_roam_event+0x393/0x560 [ath12k]
ath12k_wmi_op_rx+0x1486/0x28c0 [ath12k]
ath12k_htc_process_trailer.isra.0+0x2fb/0x620 [ath12k]
ath12k_htc_rx_completion_handler+0x448/0x830 [ath12k]
ath12k_ce_recv_process_cb+0x549/0x9e0 [ath12k]
ath12k_ce_per_engine_service+0xbe/0xf0 [ath12k]
ath12k_pci_ce_workqueue+0x69/0x120 [ath12k]
process_one_work+0xe3a/0x1430
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284.1-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: aa80f12f3b ("wifi: ath12k: defer vdev creation for MLO")
Signed-off-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250618185635.750470-1-rameshkumar.sundaram@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Fix the following 3 issues:
wifi: ath12k: avoid burning CPU while waiting for firmware stats
wifi: ath12k: don't activate more links than firmware supports
wifi: carl9170: do not ping device which has failed to load firmware
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQ/mtSHzPUi16IfDEksFbugiYzLewUCaFIHEQAKCRAsFbugiYzL
e0sRAP41jxddaDsw+Kc3JxH5D9HytK0A0x3hqfDx+IYViWjcwQD6AsdAOY7eEimL
slL7/uBiIUaytaagNc3YGb2+IffjBQM=
=b7cq
-----END PGP SIGNATURE-----
Merge tag 'ath-current-20250617' of git://git.kernel.org/pub/scm/linux/kernel/git/ath/ath
Jeff Johnson says:
==================
ath.git updates for v6.16-rc3
Fix the following 3 issues:
wifi: ath12k: avoid burning CPU while waiting for firmware stats
wifi: ath12k: don't activate more links than firmware supports
wifi: carl9170: do not ping device which has failed to load firmware
==================
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For WMI_REQUEST_VDEV_STAT request, firmware might split response into
multiple events dut to buffer limit, hence currently in
ath12k_wmi_fw_stats_process() host waits until all events received. In
case there is no vdev started, this results in that below condition
would never get satisfied
((++ar->fw_stats.num_vdev_recvd) == total_vdevs_started)
consequently the requestor would be blocked until time out.
The same applies to WMI_REQUEST_BCN_STAT request as well due to:
((++ar->fw_stats.num_bcn_recvd) == ar->num_started_vdevs)
Change to check the number of started vdev first: if it is zero, finish
directly; if not, follow the old way.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284.1-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 WLAN.WBE.1.5-01651-QCAHKSWPL_SILICONZ-1
Fixes: e367c92476 ("wifi: ath12k: Request vdev stats from firmware")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250612-ath12k-fw-fixes-v1-4-12f594f3b857@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently ath12k_wmi_fw_stats_process() is using static variables to count
firmware stat events. Taking num_vdev as an example, if for whatever
reason (say ar->num_started_vdevs is 0 or firmware bug etc.) the following
condition
(++num_vdev) == total_vdevs_started
is not met, is_end is not set thus num_vdev won't be cleared. Next time
when firmware stats is requested again, even if everything is working
fine, failure is expected due to the condition above will never be
satisfied.
The same applies to num_bcn as well.
Change to use non-static counters and reset them each time before firmware
stats is requested.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284.1-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 WLAN.WBE.1.5-01651-QCAHKSWPL_SILICONZ-1
Fixes: e367c92476 ("wifi: ath12k: Request vdev stats from firmware")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250612-ath12k-fw-fixes-v1-3-12f594f3b857@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
ath12k_mac_get_fw_stats() is busy polling fw_stats_done flag while waiting
firmware finishing sending all events. This is not good as CPU is
monopolized and kept burning during the wait.
Change to the completion mechanism to fix it.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284.1-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 WLAN.WBE.1.5-01651-QCAHKSWPL_SILICONZ-1
Fixes: e367c92476 ("wifi: ath12k: Request vdev stats from firmware")
Reported-by: Grégoire Stein <gregoire.s93@live.fr>
Closes: https://lore.kernel.org/ath12k/AS8P190MB120575BBB25FCE697CD7D4988763A@AS8P190MB1205.EURP190.PROD.OUTLOOK.COM/
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Tested-by: Grégoire Stein <gregoire.s93@live.fr>
Link: https://patch.msgid.link/20250612-ath12k-fw-fixes-v1-2-12f594f3b857@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Regarding the firmware stats events handling, the comment in
ath12k_mac_get_fw_stats() says host determines whether all events have been
received based on 'end' tag in TLV. This is wrong as there is no such tag
at all, actually host makes the decision totally by itself based on the
stats type and active pdev/vdev counts etc.
Fix it to correctly reflect the logic.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284.1-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 WLAN.WBE.1.5-01651-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250612-ath12k-fw-fixes-v1-1-12f594f3b857@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In case of ML connection, currently all useful links are activated at
ASSOC stage:
ieee80211_set_active_links(vif, ieee80211_vif_usable_links(vif))
this results in firmware crash when the number of links activated on the
same device is more than supported.
Since firmware supports activating at most 2 links for a ML connection,
to avoid firmware crash, host needs to select 2 links out of the useful
links. As the assoc link has already been chosen, the question becomes
how to determine partner links. A straightforward principle applied
here is that the resulted combination should achieve the best throughput.
For that purpose, ideally various factors like bandwidth, RSSI etc should
be considered. But that would be too complicate. To make it easy, the
choice is to only take hardware modes into consideration.
The SBS (single band simultaneously) mode frequency range covers 5 GHz
and 6 GHz bands. In this mode, the two individual MACs are both active,
with one working on 5g-high band and the other on 5g-low band (from
hardware perspective 5 GHz and 6 GHz bands are referred to as a 'large'
single 5 GHz band). The DBS (dual band simultaneously) mode covers 2 GHz
band and the 'large' 5 GHz band, with one MAC working on 2 GHz band and
the other working on 5 GHz band or 6 GHz band. Since 5,6 GHz bands could
provide higher bandwidth than 2 GHz band, the preference is given to SBS
mode. Other hardware modes results in only one working MAC at any given
time, so it is chosen only when both SBS are DBS are not possible.
For each hardware mode, if there are more than one partner candidate,
just choose the first one.
For now only single device MLO case is handled as it is easy. Other cases
could be addressed in the future.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250522-ath12k-sbs-dbs-v1-6-54a29e7a3a88@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In case of two links established on the same device in an ML connection,
depending on device's hardware mode capability, it is possible that both
links fall on the same MAC. Currently, no specific action is taken to
address this but just keep both links active. However this would result
in lower throughput compared to even one link, because switching between
these two links on the resulted MAC significantly impacts throughput.
Check if both links fall in the frequency range of a single MAC. If
so, send WMI_MLO_LINK_SET_ACTIVE_CMDID command to firmware such that
firmware can deactivate one of them. Note the decision of which link
getting deactivated is made by firmware, host only sends the vdev
lists.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250522-ath12k-sbs-dbs-v1-5-54a29e7a3a88@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Add WMI_MLO_LINK_SET_ACTIVE_CMDID command. This command allows host to
send required link information to firmware such that firmware can make
decision on activating/deactivating links in various scenarios.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250522-ath12k-sbs-dbs-v1-4-54a29e7a3a88@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Previous patches parse and save hardware MAC frequency range information
in ath12k_svc_ext_info structure. Such range represents hardware
capability hence needs to be updated based on host information, e.g. guard
the range based on host's low/high boundary.
So update frequency range. The updated range is saved in
ath12k_hw_mode_info structure and would be used when doing vdev activation
and link selection in following patches.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250522-ath12k-sbs-dbs-v1-3-54a29e7a3a88@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Firmware sends the boundary between lower and higher bands in
ath12k_wmi_dbs_or_sbs_cap_params structure embedded in
WMI_SERVICE_READY_EXT2_EVENTID event. The boundary is needed when
updating frequency range in the following patch. So parse and save
it for later use. Note ath12k_wmi_dbs_or_sbs_cap_params is placed
after some other structures, so placeholders for them are added
as well.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250522-ath12k-sbs-dbs-v1-2-54a29e7a3a88@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
WLAN hardware might support various hardware modes such as DBS (dual
band simultaneously), SBS (single band simultaneously) and DBS_OR_SBS
etc, see enum wmi_host_hw_mode_config_type. Firmware advertises actual
supported modes in WMI_SERVICE_READY_EXT_EVENTID event. For each mode,
firmware advertises frequency range each hardware MAC can operate on.
In MLO case such information is necessary during vdev activation and
link selection (which is done in following patches), so add a new
structure ath12k_svc_ext_info to ath12k_wmi_base, then parse and save
those information to it for later use.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250522-ath12k-sbs-dbs-v1-1-54a29e7a3a88@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
When the ath12k driver is built without CONFIG_ATH12K_DEBUG, the
recently refactored stats code can cause any user space application
(such at NetworkManager) to consume 100% CPU for 3 seconds, every time
stats are read.
Commit 'b8a0d83fe4c7 ("wifi: ath12k: move firmware stats out of
debugfs")' moved ath12k_debugfs_fw_stats_request() out of debugfs, by
merging the additional logic into ath12k_mac_get_fw_stats().
Among the added responsibility of ath12k_mac_get_fw_stats() was the
busy-wait for `fw_stats_done`.
Signalling of `fw_stats_done` happens when one of the
WMI_REQUEST_PDEV_STAT, WMI_REQUEST_VDEV_STAT, and WMI_REQUEST_BCN_STAT
messages are received, but the handling of the latter two commands remained
in the debugfs code. As `fw_stats_done` isn't signalled, the calling
processes will spin until the timeout (3 seconds) is reached.
Moving the handling of these two additional responses out of debugfs
resolves the issue.
Fixes: b8a0d83fe4 ("wifi: ath12k: move firmware stats out of debugfs")
Signed-off-by: Bjorn Andersson <bjorn.andersson@oss.qualcomm.com>
Tested-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://patch.msgid.link/20250609-ath12k-fw-stats-done-v1-1-2b3624656697@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Current release - regressions:
- af_unix: allow passing cred for embryo without SO_PASSCRED/SO_PASSPIDFD
Current release - new code bugs:
- eth: airoha: correct enable mask for RX queues 16-31
- veth: prevent NULL pointer dereference in veth_xdp_rcv when peer
disappears under traffic
- ipv6: move fib6_config_validate() to ip6_route_add(), prevent invalid
routes
Previous releases - regressions:
- phy: phy_caps: don't skip better duplex match on non-exact match
- dsa: b53: fix untagged traffic sent via cpu tagged with VID 0
- Revert "wifi: mwifiex: Fix HT40 bandwidth issue.", it caused transient
packet loss, exact reason not fully understood, yet
Previous releases - always broken:
- net: clear the dst when BPF is changing skb protocol (IPv4 <> IPv6)
- sched: sfq: fix a potential crash on gso_skb handling
- Bluetooth: intel: improve rx buffer posting to avoid causing issues
in the firmware
- eth: intel: i40e: make reset handling robust against multiple requests
- eth: mlx5: ensure FW pages are always allocated on the local NUMA
node, even when device is configure to 'serve' another node
- wifi: ath12k: fix GCC_GCC_PCIE_HOT_RST definition for WCN7850,
prevent kernel crashes
- wifi: ath11k: avoid burning CPU in ath11k_debugfs_fw_stats_request()
for 3 sec if fw_stats_done is not set
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=0mtm
-----END PGP SIGNATURE-----
Merge tag 'net-6.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from bluetooth and wireless.
Current release - regressions:
- af_unix: allow passing cred for embryo without SO_PASSCRED/SO_PASSPIDFD
Current release - new code bugs:
- eth: airoha: correct enable mask for RX queues 16-31
- veth: prevent NULL pointer dereference in veth_xdp_rcv when peer
disappears under traffic
- ipv6: move fib6_config_validate() to ip6_route_add(), prevent
invalid routes
Previous releases - regressions:
- phy: phy_caps: don't skip better duplex match on non-exact match
- dsa: b53: fix untagged traffic sent via cpu tagged with VID 0
- Revert "wifi: mwifiex: Fix HT40 bandwidth issue.", it caused
transient packet loss, exact reason not fully understood, yet
Previous releases - always broken:
- net: clear the dst when BPF is changing skb protocol (IPv4 <> IPv6)
- sched: sfq: fix a potential crash on gso_skb handling
- Bluetooth: intel: improve rx buffer posting to avoid causing issues
in the firmware
- eth: intel: i40e: make reset handling robust against multiple
requests
- eth: mlx5: ensure FW pages are always allocated on the local NUMA
node, even when device is configure to 'serve' another node
- wifi: ath12k: fix GCC_GCC_PCIE_HOT_RST definition for WCN7850,
prevent kernel crashes
- wifi: ath11k: avoid burning CPU in ath11k_debugfs_fw_stats_request()
for 3 sec if fw_stats_done is not set"
* tag 'net-6.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (70 commits)
selftests: drv-net: rss_ctx: Add test for ntuple rules targeting default RSS context
net: ethtool: Don't check if RSS context exists in case of context 0
af_unix: Allow passing cred for embryo without SO_PASSCRED/SO_PASSPIDFD.
ipv6: Move fib6_config_validate() to ip6_route_add().
net: drv: netdevsim: don't napi_complete() from netpoll
net/mlx5: HWS, Add error checking to hws_bwc_rule_complex_hash_node_get()
veth: prevent NULL pointer dereference in veth_xdp_rcv
net_sched: remove qdisc_tree_flush_backlog()
net_sched: ets: fix a race in ets_qdisc_change()
net_sched: tbf: fix a race in tbf_change()
net_sched: red: fix a race in __red_change()
net_sched: prio: fix a race in prio_tune()
net_sched: sch_sfq: reject invalid perturb period
net: phy: phy_caps: Don't skip better duplex macth on non-exact match
MAINTAINERS: Update Kuniyuki Iwashima's email address.
selftests: net: add test case for NAT46 looping back dst
net: clear the dst when changing skb protocol
net/mlx5e: Fix number of lanes to UNKNOWN when using data_rate_oper
net/mlx5e: Fix leak of Geneve TLV option object
net/mlx5: HWS, make sure the uplink is the last destination
...
Fix a handful of both build and stability issues across multiple drivers.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQ/mtSHzPUi16IfDEksFbugiYzLewUCaEXB6gAKCRAsFbugiYzL
e1C9AQDjoq8eMj4tlqv8bliSiF1GqgxKWtKmaujMTkNxOpgc0gD/RV4o274RPP5C
OjghnAWYRoRUjhRCKcLLoECa6xkzJQY=
=1nxf
-----END PGP SIGNATURE-----
Merge tag 'ath-current-20250608' of git://git.kernel.org/pub/scm/linux/kernel/git/ath/ath
Jeff Johnson says:
==================
ath.git updates for v6.16-rc2
Fix a handful of both build and stability issues across multiple drivers.
==================
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move this API to the canonical timer_*() namespace.
[ tglx: Redone against pre rc1 ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/aB2X0jCKQO56WdMt@gmail.com
When the execution of ath12k_core_hw_group_assign() or
ath12k_core_hw_group_create() fails, the registered notifier chain is not
unregistered properly. Its memory is freed after rmmod, which may trigger
to a use-after-free (UAF) issue if there is a subsequent access to this
notifier chain.
Fixes the issue by calling ath12k_core_panic_notifier_unregister() in
failure cases.
Call trace:
notifier_chain_register+0x4c/0x1f0 (P)
atomic_notifier_chain_register+0x38/0x68
ath12k_core_init+0x50/0x4e8 [ath12k]
ath12k_pci_probe+0x5f8/0xc28 [ath12k]
pci_device_probe+0xbc/0x1a8
really_probe+0xc8/0x3a0
__driver_probe_device+0x84/0x1b0
driver_probe_device+0x44/0x130
__driver_attach+0xcc/0x208
bus_for_each_dev+0x84/0x100
driver_attach+0x2c/0x40
bus_add_driver+0x130/0x260
driver_register+0x70/0x138
__pci_register_driver+0x68/0x80
ath12k_pci_init+0x30/0x68 [ath12k]
ath12k_init+0x28/0x78 [ath12k]
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: 6f245ea0ec ("wifi: ath12k: introduce device group abstraction")
Signed-off-by: Miaoqing Pan <miaoqing.pan@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250604055250.1228501-1-miaoqing.pan@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently a warning is reported when running:
% scripts/kernel-doc -Wall -Werror -none drivers/net/wireless/ath/ath12k/hal.h
Warning: drivers/net/wireless/ath/ath12k/hal.h:596 Enum value 'HAL_REO_CMD_RESOURCE_BLOCKED' not described in enum 'hal_reo_cmd_status'
Add the missing description of HAL_REO_CMD_RESOURCE_BLOCKED.
Link: https://patch.msgid.link/20250605-hal_reo_cmd_status-kdoc-v1-1-e59f4b814b88@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
GCC_GCC_PCIE_HOT_RST is wrongly defined for WCN7850, causing kernel crash
on some specific platforms.
Since this register is divergent for WCN7850 and QCN9274, move it to
register table to allow different definitions. Then correct the register
address for WCN7850 to fix this issue.
Note IPQ5332 is not affected as it is not PCIe based device.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Reported-by: Parth Pancholi <parth.pancholi@toradex.com>
Closes: https://lore.kernel.org/all/86899b2235a59c9134603beebe08f2bb0b244ea0.camel@gmail.com
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Tested-by: Parth Pancholi <parth.pancholi@toradex.com>
Link: https://patch.msgid.link/20250523-ath12k-wrong-global-reset-addr-v1-1-3b06eb556196@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
if ath11k_crypto_mode is invalid (not ATH11K_CRYPT_MODE_SW/ATH11K_CRYPT_MODE_HW),
ath11k_core_qmi_firmware_ready() will not undo some actions that was previously
started/configured. Do the validation as soon as possible in order to avoid
undoing actions in that case and also to fix the following smatch warning:
drivers/net/wireless/ath/ath11k/core.c:2166 ath11k_core_qmi_firmware_ready()
warn: missing unwind goto?
Signed-off-by: Rodrigo Gobbi <rodrigo.gobbi.7@gmail.com>
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Closes: https://lore.kernel.org/r/202304151955.oqAetVFd-lkp@intel.com/
Fixes: aa2092a9ba ("ath11k: add raw mode and software crypto support")
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250522200519.16858-1-rodrigo.gobbi.7@gmail.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently to get firmware stats, ath11k_mac_op_get_txpower() calls
ath11k_fw_stats_request() and ath11k_mac_op_sta_statistics() calls
ath11k_mac_get_fw_stats(). Those two helpers are basically doing
the same, except for:
1. ath11k_mac_get_fw_stats() verifies ar->state inside itself.
2. ath11k_mac_get_fw_stats() calls ath11k_mac_fw_stats_request()
which then calls ath11k_mac_fw_stats_reset() to free pdev/vdev
stats whereas only pdev stats are freed by ath11k_fw_stats_request().
3. ath11k_mac_get_fw_stats() waits for ar->fw_stats_complete and
ar->fw_stats_done, whereas ath11k_fw_stats_request() only waits for
ar->fw_stats_complete.
Change to call ath11k_mac_get_fw_stats() in ath11k_mac_op_get_txpower().
This is valid because:
1. ath11k_mac_op_get_txpower() also has the same request on ar->state.
2. it is harmless to call ath11k_fw_stats_vdevs_free() since
ar->fw_stats.vdevs should be empty and there should be no one
expecting it at that time.
3. ath11k_mac_op_get_txpower() only needs pdev stats. For pdev stats,
ar->fw_stats_done is set to true whenever ar->fw_stats_complete is
set to true in ath11k_update_stats_event(). So additional wait on
ar->fw_stats_done does not wast any time.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.37
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250220082448.31039-8-quic_bqiang@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently ath11k_mac_get_fw_stats() is acquiring/releasing ar->conf_mutex by itself.
In order to reuse this function in a context where that lock is already taken, move
lock handling to its callers, then the function itself only has to assert it.
There is only one caller now, i.e., ath11k_mac_op_sta_statistics(), so add lock handling
there.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.37
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250220082448.31039-7-quic_bqiang@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently RCU lock and ar->data_lock are acquired in a sequence of
rcu_read_lock()
spin_lock_bh(&ar->data_lock)
but released in a sequence of
rcu_read_unlock()
spin_unlock_bh(&ar->data_lock)
Although there are no apparent issues with this, reorder them to
achieve symmetry.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.37
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250220082448.31039-6-quic_bqiang@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Commit b488c76644 ("ath11k: report rssi of each chain to mac80211 for QCA6390/WCN6855")
and commit c3b39553fc ("ath11k: add signal report to mac80211 for QCA6390 and WCN6855")
call debugfs functions in mac ops. Those functions are no-ops if CONFIG_ATH11K_DEBUGFS is
not enabled, thus cause wrong status reported.
Move them to mac.c.
Besides, since WMI_REQUEST_RSSI_PER_CHAIN_STAT and WMI_REQUEST_VDEV_STAT stats could also
be requested via mac ops, process them directly in ath11k_update_stats_event().
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.37
Fixes: b488c76644 ("ath11k: report rssi of each chain to mac80211 for QCA6390/WCN6855")
Fixes: c3b39553fc ("ath11k: add signal report to mac80211 for QCA6390 and WCN6855")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250220082448.31039-5-quic_bqiang@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
For WMI_REQUEST_VDEV_STAT request, firmware might split response into
multiple events dut to buffer limit, hence currently in
ath11k_debugfs_fw_stats_process() we wait until all events received.
In case there is no vdev started, this results in that below condition
would never get satisfied
((++ar->fw_stats.num_vdev_recvd) == total_vdevs_started)
finally the requestor would be blocked until wait time out.
The same applies to WMI_REQUEST_BCN_STAT request as well due to:
((++ar->fw_stats.num_bcn_recvd) == ar->num_started_vdevs)
Change to check the number of started vdev first: if it is zero, finish
wait directly; if not, follow the old way.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.37
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250220082448.31039-4-quic_bqiang@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently ath11k_debugfs_fw_stats_process() is using static variables to count
firmware stat events. Taking num_vdev as an example, if for whatever reason (
say ar->num_started_vdevs is 0 or firmware bug etc.) the following condition
(++num_vdev) == total_vdevs_started
is not met, is_end is not set thus num_vdev won't be cleared. Next time when
firmware stats is requested again, even if everything is working fine, we will
fail due to the condition above will never be satisfied.
The same applies to num_bcn as well.
Change to use non-static counters so that we have a chance to clear them each
time firmware stats is requested. Currently only ath11k_fw_stats_request() and
ath11k_debugfs_fw_stats_request() are requesting firmware stats, so clear
counters there.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.37
Fixes: da3a9d3c15 ("ath11k: refactor debugfs code into debugfs.c")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250220082448.31039-3-quic_bqiang@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
We get report [1] that CPU is running a hot loop in
ath11k_debugfs_fw_stats_request():
94.60% 0.00% i3status [kernel.kallsyms] [k] do_syscall_64
|
--94.60%--do_syscall_64
|
--94.55%--__sys_sendmsg
___sys_sendmsg
____sys_sendmsg
netlink_sendmsg
netlink_unicast
genl_rcv
netlink_rcv_skb
genl_rcv_msg
|
--94.55%--genl_family_rcv_msg_dumpit
__netlink_dump_start
netlink_dump
genl_dumpit
nl80211_dump_station
|
--94.55%--ieee80211_dump_station
sta_set_sinfo
|
--94.55%--ath11k_mac_op_sta_statistics
ath11k_debugfs_get_fw_stats
|
--94.55%--ath11k_debugfs_fw_stats_request
|
|--41.73%--_raw_spin_lock_bh
|
|--22.74%--__local_bh_enable_ip
|
|--9.22%--_raw_spin_unlock_bh
|
--6.66%--srso_alias_safe_ret
This is because, if for whatever reason ar->fw_stats_done is not set by
ath11k_update_stats_event(), ath11k_debugfs_fw_stats_request() won't yield
CPU before an up to 3s timeout.
Change to completion mechanism to avoid CPU burning.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.37
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Reported-by: Yury Vostrikov <mon@unformed.ru>
Closes: https://lore.kernel.org/all/7324ac7a-8b7a-42a5-aa19-de52138ff638@app.fastmail.com/ # [1]
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250220082448.31039-2-quic_bqiang@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
the wil6210 driver irq handling code is unconditionally writing
edma irq registers which are supposed to be only used on Talyn chipsets.
This however leade to a chipset hang on the older sparrow chipset
generation and firmware will not even boot.
Fix that by simply checking for edma support before handling these
registers.
Tested on Netgear R9000
Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Link: https://patch.msgid.link/20250304012131.25970-2-s.gottschall@dd-wrt.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In some scenarios, the firmware may be stopped before the interface is
removed, either due to a crash or because the remoteproc (e.g., MPSS)
is shut down early during system reboot or shutdown.
This leads to a delay during interface teardown, as the driver waits for
a vdev delete response that never arrives, eventually timing out.
Example (SNOC):
$ echo stop > /sys/class/remoteproc/remoteproc0/state
[ 71.64] remoteproc remoteproc0: stopped remote processor modem
$ reboot
[ 74.84] ath10k_snoc c800000.wifi: failed to transmit packet, dropping: -108
[ 74.84] ath10k_snoc c800000.wifi: failed to submit frame: -108
[...]
[ 82.39] ath10k_snoc c800000.wifi: Timeout in receiving vdev delete response
To avoid this, skip waiting for the vdev delete response if the firmware is
already marked as unreachable (`ATH10K_FLAG_CRASH_FLUSH`), similar to how
`ath10k_mac_wait_tx_complete()` and `ath10k_vdev_setup_sync()` handle this case.
Signed-off-by: Loic Poulain <loic.poulain@oss.qualcomm.com>
Link: https://patch.msgid.link/20250522131704.612206-1-loic.poulain@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In ath10k_snoc_hif_stop() we skip disabling the IRQs in the crash
recovery flow, but we still unconditionally call enable again in
ath10k_snoc_hif_start().
We can't check the ATH10K_FLAG_CRASH_FLUSH bit since it is cleared
before hif_start() is called, so instead check the
ATH10K_SNOC_FLAG_RECOVERY flag and skip enabling the IRQs during crash
recovery.
This fixes unbalanced IRQ enable splats that happen after recovering from
a crash.
Fixes: 0e622f67e0 ("ath10k: add support for WCN3990 firmware crash recovery")
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Tested-by: Loic Poulain <loic.poulain@oss.qualcomm.com>
Link: https://patch.msgid.link/20250318205043.1043148-1-caleb.connolly@linaro.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
-----BEGIN PGP SIGNATURE-----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=eWJw
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Print the actual delay time in pci_bridge_wait_for_secondary_bus()
instead of assuming it was 1000ms (Wilfred Mallawa)
- Revert 'iommu/amd: Prevent binding other PCI drivers to IOMMU PCI
devices', which broke resume from system sleep on AMD platforms and
has been fixed by other commits (Lukas Wunner)
Resource management:
- Remove mtip32xx use of pcim_iounmap_regions(), which is deprecated
and unnecessary (Philipp Stanner)
- Remove pcim_iounmap_regions() and pcim_request_region_exclusive()
and related flags since all uses have been removed (Philipp
Stanner)
- Rework devres 'request' functions so they are no longer 'hybrid',
i.e., their behavior no longer depends on whether
pcim_enable_device or pci_enable_device() was used, and remove
related code (Philipp Stanner)
- Warn (not BUG()) about failure to assign optional resources (Ilpo
Järvinen)
Error handling:
- Log the DPC Error Source ID only when it's actually valid (when
ERR_FATAL or ERR_NONFATAL was received from a downstream device)
and decode into bus/device/function (Bjorn Helgaas)
- Determine AER log level once and save it so all related messages
use the same level (Karolina Stolarek)
- Use KERN_WARNING, not KERN_ERR, when logging PCIe Correctable
Errors (Karolina Stolarek)
- Ratelimit PCIe Correctable and Non-Fatal error logging, with sysfs
controls on interval and burst count, to avoid flooding logs and
RCU stall warnings (Jon Pan-Doh)
Power management:
- Increment PM usage counter when probing reset methods so we don't
try to read config space of a powered-off device (Alex Williamson)
- Set all devices to D0 during enumeration to ensure ACPI opregion is
connected via _REG (Mario Limonciello)
Power control:
- Rename pwrctrl Kconfig symbols from 'PWRCTL' to 'PWRCTRL' to match
the filename paths. Retain old deprecated symbols for
compatibility, except for the pwrctrl slot driver
(PCI_PWRCTRL_SLOT) (Johan Hovold)
- When unregistering pwrctrl, cancel outstanding rescan work before
cleaning up data structures to avoid use-after-free issues (Brian
Norris)
Bandwidth control:
- Simplify link bandwidth controller by replacing the count of Link
Bandwidth Management Status (LBMS) events with a PCI_LINK_LBMS_SEEN
flag (Ilpo Järvinen)
- Update the Link Speed after retraining, since the Link Speed may
have changed (Ilpo Järvinen)
PCIe native device hotplug:
- Ignore Presence Detect Changed caused by DPC.
pciehp already ignores Link Down/Up events caused by DPC, but on
slots using in-band presence detect, DPC causes a spurious Presence
Detect Changed event (Lukas Wunner)
- Ignore Link Down/Up caused by Secondary Bus Reset.
On hotplug ports using in-band presence detect, the reset causes a
Presence Detect Changed event, which mistakenly caused teardown and
re-enumeration of the device. Drivers may need to annotate code
that resets their device (Lukas Wunner)
Virtualization:
- Add an ACS quirk for Loongson Root Ports that don't advertise ACS
but don't allow peer-to-peer transactions between Root Ports; the
quirk allows each Root Port to be in a separate IOMMU group (Huacai
Chen)
Endpoint framework:
- For fixed-size BARs, retain both the actual size and the possibly
larger size allocated to accommodate iATU alignment requirements
(Jerome Brunet)
- Simplify ctrl/SPAD space allocation and avoid allocating more space
than needed (Jerome Brunet)
- Correct MSI-X PBA offset calculations for DesignWare and Cadence
endpoint controllers (Niklas Cassel)
- Align the return value (number of interrupts) encoding for
pci_epc_get_msi()/pci_epc_ops::get_msi() and
pci_epc_get_msix()/pci_epc_ops::get_msix() (Niklas Cassel)
- Align the nr_irqs parameter encoding for
pci_epc_set_msi()/pci_epc_ops::set_msi() and
pci_epc_set_msix()/pci_epc_ops::set_msix() (Niklas Cassel)
Common host controller library:
- Convert pci-host-common to a library so platforms that don't need
native host controller drivers don't need to include these helper
functions (Manivannan Sadhasivam)
Apple PCIe controller driver:
- Extract ECAM bridge creation helper from pci_host_common_probe() to
separate driver-specific things like MSI from PCI things (Marc
Zyngier)
- Dynamically allocate RID-to_SID bitmap to prepare for SoCs with
varying capabilities (Marc Zyngier)
- Skip ports disabled in DT when setting up ports (Janne Grunau)
- Add t6020 compatible string (Alyssa Rosenzweig)
- Add T602x PCIe support (Hector Martin)
- Directly set/clear INTx mask bits because T602x dropped the
accessors that could do this without locking (Marc Zyngier)
- Move port PHY registers to their own reg items to accommodate
T602x, which moves them around; retain default offsets for existing
DTs that lack phy%d entries with the reg offsets (Hector Martin)
- Stop polling for core refclk, which doesn't work on T602x and the
bootloader has already done anyway (Hector Martin)
- Use gpiod_set_value_cansleep() when asserting PERST# in probe
because we're allowed to sleep there (Hector Martin)
Cadence PCIe controller driver:
- Drop a runtime PM 'put' to resolve a runtime atomic count underflow
(Hans Zhang)
- Make the cadence core buildable as a module (Kishon Vijay Abraham I)
- Add cdns_pcie_host_disable() and cdns_pcie_ep_disable() for use by
loadable drivers when they are removed (Siddharth Vadapalli)
Freescale i.MX6 PCIe controller driver:
- Apply link training workaround only on IMX6Q, IMX6SX, IMX6SP
(Richard Zhu)
- Remove redundant dw_pcie_wait_for_link() from
imx_pcie_start_link(); since the DWC core does this, imx6 only
needs it when retraining for a faster link speed (Richard Zhu)
- Toggle i.MX95 core reset to align with PHY powerup (Richard Zhu)
- Set SYS_AUX_PWR_DET to work around i.MX95 ERR051624 erratum: in
some cases, the controller can't exit 'L23 Ready' through Beacon or
PERST# deassertion (Richard Zhu)
- Clear GEN3_ZRXDC_NONCOMPL to work around i.MX95 ERR051586 erratum:
controller can't meet 2.5 GT/s ZRX-DC timing when operating at 8
GT/s, causing timeouts in L1 (Richard Zhu)
- Wait for i.MX95 PLL lock before enabling controller (Richard Zhu)
- Save/restore i.MX95 LUT for suspend/resume (Richard Zhu)
Mobiveil PCIe controller driver:
- Return bool (not int) for link-up check in
mobiveil_pab_ops.link_up() and layerscape-gen4, mobiveil (Hans
Zhang)
NVIDIA Tegra194 PCIe controller driver:
- Create debugfs directory for 'aspm_state_cnt' only when
CONFIG_PCIEASPM is enabled, since there are no other entries (Hans
Zhang)
Qualcomm PCIe controller driver:
- Add OF support for parsing DT 'eq-presets-<N>gts' property for lane
equalization presets (Krishna Chaitanya Chundru)
- Read Maximum Link Width from the Link Capabilities register if DT
lacks 'num-lanes' property (Krishna Chaitanya Chundru)
- Add Physical Layer 64 GT/s Capability ID and register offsets for
8, 32, and 64 GT/s lane equalization registers (Krishna Chaitanya
Chundru)
- Add generic dwc support for configuring lane equalization presets
(Krishna Chaitanya Chundru)
- Add DT and driver support for PCIe on IPQ5018 SoC (Nitheesh Sekar)
Renesas R-Car PCIe controller driver:
- Describe endpoint BAR 4 as being fixed size (Jerome Brunet)
- Document how to obtain R-Car V4H (r8a779g0) controller firmware
(Yoshihiro Shimoda)
Rockchip PCIe controller driver:
- Reorder rockchip_pci_core_rsts because
reset_control_bulk_deassert() deasserts in reverse order, to fix a
link training regression (Jensen Huang)
- Mark RK3399 as being capable of raising INTx interrupts (Niklas
Cassel)
Rockchip DesignWare PCIe controller driver:
- Check only PCIE_LINKUP, not LTSSM status, to determine whether the
link is up (Shawn Lin)
- Increase N_FTS (used in L0s->L0 transitions) and enable ASPM L0s
for Root Complex and Endpoint modes (Shawn Lin)
- Hide the broken ATS Capability in rockchip_pcie_ep_init() instead
of rockchip_pcie_ep_pre_init() so it stays hidden after PERST#
resets non-sticky registers (Shawn Lin)
- Call phy_power_off() before phy_exit() in rockchip_pcie_phy_deinit()
(Diederik de Haas)
Synopsys DesignWare PCIe controller driver:
- Set PORT_LOGIC_LINK_WIDTH to one lane to make initial link training
more robust; this will not affect the intended link width if all
lanes are functional (Wenbin Yao)
- Return bool (not int) for link-up check in dw_pcie_ops.link_up()
and armada8k, dra7xx, dw-rockchip, exynos, histb, keembay,
keystone, kirin, meson, qcom, qcom-ep, rcar_gen4, spear13xx,
tegra194, uniphier, visconti (Hans Zhang)
- Add debugfs support for exposing DWC device-specific PTM context
(Manivannan Sadhasivam)
TI J721E PCIe driver:
- Make j721e buildable as a loadable and removable module (Siddharth
Vadapalli)
- Fix j721e host/endpoint dependencies that result in link failures
in some configs (Arnd Bergmann)
Device tree bindings:
- Add qcom DT binding for 'global' interrupt (PCIe controller and
link-specific events) for ipq8074, ipq8074-gen3, ipq6018, sa8775p,
sc7280, sc8180x sdm845, sm8150, sm8250, sm8350 (Manivannan
Sadhasivam)
- Add qcom DT binding for 8 MSI SPI interrupts for msm8998, ipq8074,
ipq8074-gen3, ipq6018 (Manivannan Sadhasivam)
- Add dw rockchip DT binding for rk3576 and rk3562 (Kever Yang)
- Correct indentation and style of examples in brcm,stb-pcie,
cdns,cdns-pcie-ep, intel,keembay-pcie-ep, intel,keembay-pcie,
microchip,pcie-host, rcar-pci-ep, rcar-pci-host, xilinx-versal-cpm
(Krzysztof Kozlowski)
- Convert Marvell EBU (dove, kirkwood, armada-370, armada-xp) and
armada8k from text to schema DT bindings (Rob Herring)
- Remove obsolete .txt DT bindings for content that has been moved to
schemas (Rob Herring)
- Add qcom DT binding for MHI registers in IPQ5332, IPQ6018, IPQ8074
and IPQ9574 (Varadarajan Narayanan)
- Convert v3,v360epc-pci from text to DT schema binding (Rob Herring)
- Change microchip,pcie-host DT binding to be 'dma-noncoherent' since
PolarFire may be configured that way (Conor Dooley)
Miscellaneous:
- Drop 'pci' suffix from intel_mid_pci.c filename to match similar
files (Andy Shevchenko)
- All platforms with PCI have an MMU, so add PCI Kconfig dependency
on MMU to simplify build testing and avoid inadvertent build
regressions (Arnd Bergmann)
- Update Krzysztof Wilczyński's email address in MAINTAINERS
(Krzysztof Wilczyński)
- Update Manivannan Sadhasivam's email address in MAINTAINERS
(Manivannan Sadhasivam)"
* tag 'pci-v6.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (147 commits)
MAINTAINERS: Update Manivannan Sadhasivam email address
PCI: j721e: Fix host/endpoint dependencies
PCI: j721e: Add support to build as a loadable module
PCI: cadence-ep: Introduce cdns_pcie_ep_disable() helper for cleanup
PCI: cadence-host: Introduce cdns_pcie_host_disable() helper for cleanup
PCI: cadence: Add support to build pcie-cadence library as a kernel module
MAINTAINERS: Update Krzysztof Wilczyński email address
PCI: Remove unnecessary linesplit in __pci_setup_bridge()
PCI: WARN (not BUG()) when we fail to assign optional resources
PCI: Remove unused pci_printk()
PCI: qcom: Replace PERST# sleep time with proper macro
PCI: dw-rockchip: Replace PERST# sleep time with proper macro
PCI: host-common: Convert to library for host controller drivers
PCI/ERR: Remove misleading TODO regarding kernel panic
PCI: cadence: Remove duplicate message code definitions
PCI: endpoint: Align pci_epc_set_msix(), pci_epc_ops::set_msix() nr_irqs encoding
PCI: endpoint: Align pci_epc_set_msi(), pci_epc_ops::set_msi() nr_irqs encoding
PCI: endpoint: Align pci_epc_get_msix(), pci_epc_ops::get_msix() return value encoding
PCI: endpoint: Align pci_epc_get_msi(), pci_epc_ops::get_msi() return value encoding
PCI: cadence-ep: Correct PBA offset in .set_msix() callback
...
The PCI_PWRCTRL_PWRSEQ and HAVE_PWRCTRL symbols have been renamed to
reflect the pwrctrl framework name. Switch to the non-deprecated symbols.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jeff Johnson <jjohnson@kernel.org> # drivers/net/wireless/ath/...
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://patch.msgid.link/20250402132634.18065-4-johan+linaro@kernel.org
The PCI_PWRCTRL_PWRSEQ and HAVE_PWRCTRL symbols have been renamed to
reflect the pwrctrl framework name. Switch to the non-deprecated symbols.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jeff Johnson <jjohnson@kernel.org> # drivers/net/wireless/ath/...
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://patch.msgid.link/20250402132634.18065-3-johan+linaro@kernel.org
ath12k:
Add monitor mode support for WCN7850.
Enhance regulatory support including 6 GHz power modes.
In addition, perform the usual set of bug fixes and cleanups across
all supported drivers.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQ/mtSHzPUi16IfDEksFbugiYzLewUCaC5IEwAKCRAsFbugiYzL
ezMUAQCAH3sy0hJSraoLb+6+VMI/ClBquJVIgOBwVvlXJd4lIgEAwY+uYgSNWkYU
KQ2Zxa8+whDx6oqFJF5qYJ+scMh9VA0=
=b7Wk
-----END PGP SIGNATURE-----
Merge tag 'ath-next-20250521' of git://git.kernel.org/pub/scm/linux/kernel/git/ath/ath
Jeff Johnson says:
==================
ath.git patches for v6.16
ath12k:
Add monitor mode support for WCN7850.
Enhance regulatory support including 6 GHz power modes.
In addition, perform the usual set of bug fixes and cleanups across
all supported drivers.
==================
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 7ed3e88664 ("wifi: ath12k: update regulatory rules when connection
established") introduced a call to ath12k_reg_handle_chan_list() upon
connection to update the regulatory domain in cfg80211 based on the power
type received from the AP.
However, this update fails because ah->regd_updated was already set to true
during the earlier regulatory update triggered when the interface was
added.
To resolve this, reset ah->regd_updated before calling
ath12k_reg_handle_chan_list() to ensure the update proceeds correctly.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Fixes: 7ed3e88664 ("wifi: ath12k: update regulatory rules when connection established")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250521-ath12k-fix-ah-regd_updated-v1-3-9737de5bf98e@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Commit 4c546023d7 ("wifi: ath12k: update regulatory rules when interface
added"), introduced a call to ath12k_reg_handle_chan_list() during
interface addition to update the regulatory domain based on the interface
type. While this works initially, subsequent updates (e.g., after an
interface delete/re-add cycle) fail because ah->regd_updated is never
reset.
To address this, reset ah->regd_updated before calling
ath12k_reg_handle_chan_list() to allow the update to proceed.
However, this change exposes another issue: a timeout occurs when waiting
for the 11D scan to complete, as seen in the log:
ath12k_pci 0000:05:00.0: failed to receive 11d scan complete: timed out
This happens because during interface down, ar->state_11d is set to
ATH12K_11D_PREPARING, and during interface up, the host waits for
ar->completed_11d_scan even though the scan hasn't started yet.
Fix this by updating the wait condition to check for ATH12K_11D_RUNNING,
which is the only state where a scan complete event is expected.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Fixes: 4c546023d7 ("wifi: ath12k: update regulatory rules when interface added")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250521-ath12k-fix-ah-regd_updated-v1-2-9737de5bf98e@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In the current implementation of ath12k_regd_update(), the ah->regd_updated
flag is used to ensure that the regulatory domain is updated only once per
radio. During MAC registration, this function is called to push the default
regulatory domain to cfg80211. At that point, the hardware state is not on
and hence ah->regd_updated remains false.
However, after commit 4c546023d7 ("wifi: ath12k: update regulatory rules
when interface added"), ath12k_reg_handle_chan_list() is invoked when an
interface is added, which in turn calls ath12k_regd_update(). By this time,
hardware state is on and consecutively ah->regd_updated becomes true.
Later, when the 11D scan completes and a new regulatory domain is received
from the firmware, the host attempts to update cfg80211 again via
ath12k_regd_update(). But since ah->regd_updated is already true, the
update is skipped.
>From the user's perspective, this results in a failure to connect to 6 GHz
APs, as the default regulatory domain (the only one pushed to cfg80211)
does not include 6 GHz support.
To resolve this, reset the ah->regd_updated flag when handling the 11D
regulatory domain update.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Fixes: 591de41d70 ("wifi: ath12k: add 11d scan offload support")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250521-ath12k-fix-ah-regd_updated-v1-1-9737de5bf98e@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Checking the SOCK_WIFI_STATUS flag bit in sk_flags may give wrong results
since sk_flags are part of a union and the union is used otherwise. Add
sk_requests_wifi_status() which checks if sk is non-NULL, sk is a full
socket (so flags are valid) and checks the flag bit.
Fixes: 76a853f86c ("wifi: free SKBTX_WIFI_STATUS skb tx_flags flag")
Suggested-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Bert Karwatzki <spasswolf@web.de>
Reviewed-by: Jason Xing <kerneljasonxing@gmail.com>
Link: https://patch.msgid.link/20250520223430.6875-1-spasswolf@web.de
[edit commit message, fix indentation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current implementation of per-pdev frequency range updates assumes that
each pdev supports only a single band. As a result in ath12k_regd_update(),
bands are handled using an if-else structure, which limits updates to only
one of the band per pdev. This assumption does not hold for all chipsets.
For example, the WCN7850 supports multiple bands within a single pdev.
Hence to accommodate such cases, update the logic to account for all band
cases by handling each band in a separate if conditions instead of the
previous if-else structure.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Fixes: 13324cecbb ("wifi: ath12k: Update frequency range if reg rules changes")
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250520-fix_freq_range_update-v1-1-e061fd147b87@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The function calls bitmap_empty() just before find_first_bit(). Both
functions are O(N). Because find_first_bit() returns >= nbits in case of
empty bitmap, the bitmap_empty() test may be avoided.
Signed-off-by: Yury Norov <yury.norov@gmail.com>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
Link: https://patch.msgid.link/20250326155200.39895-1-yury.norov@gmail.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
A malicious USB device can send a WMI_SWBA_EVENTID event from an
ath9k_htc-managed device before beaconing has been enabled. This causes
a device-by-zero error in the driver, leading to either a crash or an
out of bounds read.
Prevent this by aborting the handling in ath9k_htc_swba() if beacons are
not enabled.
Reported-by: Robert Morris <rtm@csail.mit.edu>
Closes: https://lore.kernel.org/r/88967.1743099372@localhost
Fixes: 832f6a18fc ("ath9k_htc: Add beacon slots")
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://patch.msgid.link/20250402112217.58533-1-toke@toke.dk
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Whenever there is a change in the country code settings from the
user, driver does an intersection of the regulatory rules for this
new country with the original regulatory rules which were reported
during initialization time.
There is also similar logic running in firmware with a difference
that the intersection in firmware is only done when the country code
is configuration during boot up time (BDF/OTP). Firmware logic does
not kick in when no country code is configured during device bring
up time as the device is always expected to have the country code
configured properly in the deployment.
There is a debug/test use case that requires absolute regulatory
rules to be used for a user configured country code when the device
is not configured with a particular country code during boot up time.
To support the above test use case, remove the redundant regulatory
rules intersection logic in the host driver. Depend on the
intersection logic in firmware when the device comes up with
pre-configured country code.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00209-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aishwarya R <quic_aisr@quicinc.com>
Signed-off-by: Rajat Soni <quic_rajson@quicinc.com>
Link: https://patch.msgid.link/20250505034351.1365914-1-quic_rajson@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
As per IEEE 802.11be-2024 - 9.4.2.321, EHT operation element
contains MCS15 Disable subfield as the sixth bit, which is set when
MCS15 support is not enabled.
During association, firmware will use this MCS15 flag to enable or
disable the reception of PPDU with EHT-MCS15 capability.
Send MCS15 support to firmware through WMI command during peer assoc.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Co-developed-by: Dhanavandhana Kannan <quic_dhanavan1@quicinc.com>
Signed-off-by: Dhanavandhana Kannan <quic_dhanavan1@quicinc.com>
Signed-off-by: Mohan Kumar G <quic_mkumarg@quicinc.com>
Link: https://patch.msgid.link/20250505153536.3275145-1-quic_mkumarg@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
During a code review, it is observed that in the scenario
where scan initiation fails, the current code schedules the
ar->scan.timeout workqueue which is not necessary.
In the scan initiation failure scenario, exit the code instead
of scheduling the ar->scan.timeout workqueue.
Compile tested only.
Signed-off-by: Vignesh C <quic_vignc@quicinc.com>
Link: https://patch.msgid.link/20250512065849.2833232-1-quic_vignc@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Users of the Lenovo ThinkPad X13s have reported that Wi-Fi sometimes
breaks and the log fills up with errors like:
ath11k_pci 0006:01:00.0: HTC Rx: insufficient length, got 1484, expected 1492
ath11k_pci 0006:01:00.0: HTC Rx: insufficient length, got 1460, expected 1484
which based on a quick look at the ath11k driver seemed to indicate some
kind of ring-buffer corruption.
Miaoqing Pan tracked it down to the host seeing the updated destination
ring head pointer before the updated descriptor, and the error handling
for that in turn leaves the ring buffer in an inconsistent state.
While this has not yet been observed with ath12k, the ring-buffer
implementation is very similar to the ath11k one and it suffers from the
same bugs.
Add the missing memory barrier to make sure that the descriptor is read
after the head pointer to address the root cause of the corruption while
fixing up the error handling in case there are ever any (ordering) bugs
on the device side.
Note that the READ_ONCE() are only needed to avoid compiler mischief in
case the ring-buffer helpers are ever inlined.
Tested-on: WCN7850 hw2.0 WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Cc: stable@vger.kernel.org # 6.3
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218623
Link: https://lore.kernel.org/20250310010217.3845141-3-quic_miaoqing@quicinc.com
Cc: Miaoqing Pan <quic_miaoqing@quicinc.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Miaoqing Pan <quic_miaoqing@quicinc.com>
Link: https://patch.msgid.link/20250321095219.19369-1-johan+linaro@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Introduce 'firmware-name' property to allow end-users and/or integrators to
decide which usecase-specific firmware to run on the WCN7850 platform. This
is necessary due to resource limitations such as memory capacity and CPU
capability, or performance and power optimization for different application
scenarios.
Currently, there are two firmwares, both files can be executed
interchangeably.
For example:
- ath12k/WCN7850/hw2.0/amss.bin,
ath12k/WCN7850/hw2.0/m3.bin
ath12k/WCN7850/hw2.0/board-2.bin
- ath12k/WCN7850/hw2.0/ncm825/amss.bin,
ath12k/WCN7850/hw2.0/ncm825/m3.bin
ath12k/WCN7850/hw2.0/board-2.bin
The former is the default firmware, suitable for most WiFi 7 STA functions.
The latter adds support for commercial-quality SAP and optimizes power
consumption for IoT applications. And both use the same BDF/regdb data
within the main board-2.bin.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Miaoqing Pan <quic_miaoqing@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250424005703.2479907-3-quic_miaoqing@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Due to the change in the resource release order in ath12k_core_deinit(),
the resource release order in the AHB bus removal process needs to be
adjusted accordingly.
Tested-on: IPQ5332 hw1.0 AHB WLAN.WBE.1.3.1-00130-QCAHKSWPL_SILICONZ-1
Fixes: 6cee30f0da ("wifi: ath12k: add AHB driver support for IPQ5332")
Signed-off-by: Yingying Tang <quic_yintang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250423055650.16230-3-quic_yintang@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Ath12k panic notifier is registered in driver loading process. But it is not
unregistered if ATH12K_FLAG_QMI_FAIL is set(e.g. load BDF failed) and unload
driver. It causes a dirty node in panic notifier list since ath12k panic
notifier is not unregistered from list but the buffer of this node is freed
in driver unloading process. If load driver again there will be a page fault
error due to this dirty node in panic notifier list.
This issue is caused by asymmetry between ath12k_core_init() and
ath12k_core_deinit(). Reorder and relocate the release of resources in
ath12k_core_deinit() to avoid this asymmetry issue.
Call Trace:
<TASK>
? show_regs+0x67/0x70
? __die_body+0x20/0x70
? __die+0x2b/0x40
? page_fault_oops+0x15d/0x500
? search_bpf_extables+0x63/0x90
? notifier_chain_register+0x21/0xe0
? search_exception_tables+0x5f/0x70
? kernelmode_fixup_or_oops.isra.0+0x61/0x80
? __bad_area_nosemaphore+0x179/0x240
? bad_area_nosemaphore+0x16/0x20
? do_user_addr_fault+0x312/0x7f0
? prb_read_valid+0x1c/0x30
? exc_page_fault+0x78/0x180
? asm_exc_page_fault+0x27/0x30
? notifier_chain_register+0x21/0xe0
? notifier_chain_register+0x55/0xe0
atomic_notifier_chain_register+0x2c/0x50
ath12k_core_init+0x7e/0x110 [ath12k]
ath12k_pci_probe+0xaba/0xba0 [ath12k]
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0-02903-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: 809055628b ("wifi: ath12k: add panic handler")
Signed-off-by: Yingying Tang <quic_yintang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250423055650.16230-2-quic_yintang@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Add support for data path related device specific stats. This
information helps to debug connectivity and performance issues
in AP, STA, and Mesh modes.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00210-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Vinith Kumar R <quic_vinithku@quicinc.com>
Signed-off-by: Nithyanantham Paramasivam <nithyanantham.paramasivam@oss.qualcomm.com>
Reviewed-by: Mahendran P <quic_mahep@quicinc.com>
Link: https://patch.msgid.link/20250425012802.698914-3-nithyanantham.paramasivam@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
To have consistent nomenclature, replace the use of the term "soc"
with the term "device".
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00210-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Vinith Kumar R <quic_vinithku@quicinc.com>
Signed-off-by: Nithyanantham Paramasivam <nithyanantham.paramasivam@oss.qualcomm.com>
Reviewed-by: Mahendran P <quic_mahep@quicinc.com>
Link: https://patch.msgid.link/20250425012802.698914-2-nithyanantham.paramasivam@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
When processing a "station dump" command, the driver retrieves RSSI
values from the HAL_PHYRX_RSSI_LEGACY TLV received from the monitor
destination ring, and reports them to userspace. Currently, the RSSI
values reported are improper because the hardware has not been
configured to update them properly.
To fix this, enable the HTT_RX_FILTER_TLV_FLAGS_PPDU_START_USER_INFO in
the filter setup to ensure the correct RSSI values are returned in the
HAL_PHYRX_RSSI_LEGACY TLV, resulting in correct RSSI values being
reported to userspace.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00218-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: P Praneesh <praneesh.p@oss.qualcomm.com>
Signed-off-by: Sowjanya vardhineni <quic_svardhin@quicinc.com>
Reviewed-by: Mahendran P <quic_mahep@quicinc.com>
Link: https://patch.msgid.link/20250424055104.2503723-1-quic_svardhin@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Three out of four callers to ath12k_mac_get_tx_arvif() have
link_conf pointer already set for other operations. Pass it
as a parameter. Modify ath12k_control_beaconing() to set
link_conf first.
Signed-off-by: Aloka Dixit <aloka.dixit@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250408184501.3715887-4-aloka.dixit@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
When EMLSR operation is enabled for an ML Station, EMLSR transition
timeout, padding delay and transition delay should be updated to
Firmware. Above parameters will be used by Firmware to do EMLSR operation
such as sending EML operation mode notification frame, initial control
frame etc.
Obtain above parameters from EML capabilities information present in
ieee80211_sta object and update the same to Firmware in peer assoc WMI
command sent for ML station.
MLO is not enabled in WCN7850 and hence this change is not applicable to
it as of now. This can be a leverage once it is enabled in future.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Ramasamy Kaliappan <quic_rkaliapp@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250327051320.3253783-5-quic_ramess@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Since dynamic VLAN traffic is software encrypted and encapsulated,
mac80211 handles the duplication on each link for MLO dynamic VLAN
multicast.
Currently in ath12k_mac_op_tx(), all multicast frames are duplicated
and are assigned a mcbc_gsn. This is causing dynamic VLAN multicast
traffic to be dropped in hardware.
Prevent dynamic VLAN multicast traffic from being duplicated again in
the driver. Check if incoming packet is a dynamic VLAN packet and
avoid defaulting to multicast conditional.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Muna Sinada <muna.sinada@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250424221404.1262597-1-muna.sinada@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, TCL performs the TX address search for each entry during
transmission, which may lead to packet delays.
To mitigate this issue, enable AST index-based address search during
transmission in station mode. This AST index-based search is not
enabled in AP mode due to the complexity involved in fetching peer
information.
Implement changes to retrieve the offset of ast_idx/ast_hash values
from the PEER_MAP3 event, update the vdev search type to ADDRX, and
enable AST lookup in the bank configuration.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Thiraviyam Mariyappan <quic_tmariyap@quicinc.com>
Signed-off-by: Nithyanantham Paramasivam <nithyanantham.paramasivam@oss.qualcomm.com>
Reviewed-by: Mahendran P <quic_mahep@quicinc.com>
Link: https://patch.msgid.link/20250422094255.131226-1-nithyanantham.paramasivam@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In ath12k_dp_mon_rx_merg_msdus(), will set packet offset to 8. This is a
right value for QCN9274.
But WCN7850 use different hardware rings for monitor mode because it
doesn't have RX MON component. So the packet offset is different. With
current offset, upper-layer application will failed to parse the payload
correctly.
Should use different value for those who don't have RX MON component.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Kang Yang <kang.yang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250421023444.1778-13-kang.yang@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Some monitor parameters are only initialized for QCN9274, but WCN7850
also needs them, so initialize them for WCN7850 as well.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Kang Yang <kang.yang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250421023444.1778-12-kang.yang@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
WCN7850 uses error dst ring as mon dest ring. Each time hardware
receives a packet, will fill the payload into mon dest ring.
The mon dest ring may store many MSDUs, which belonged to different
MPDUs. Need to retrieve MSDUs based on the PPDU ID, only processing the
MSDUs with same PPDU ID each time.
The PPDU ID is used in cycles, the difference between the PPDU IDs
of the two rings must be checked. If the status PPDU ID minus the
dest PPDU ID is greater than 20000, it is considered a wrap-around
case.
After reaping the mon dest ring, should prepare packet and deliver it to
mac80211 when status PPDU ID is equal to dest PPDU ID. Then start to
process next PPDU if exists.
But if dest PPDU ID > status PPDU ID, should hold on to mon dest ring
processing. If it exceeds 16 consecutive times, status PPDU ID will be
forcibly set to dest PPDU ID to avoid backpressure issue.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Kang Yang <kang.yang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250421023444.1778-11-kang.yang@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, ath12k_dp_rx_link_desc_return() takes struct
hal_reo_dest_ring as its second input. This struct is converted to
struct hal_wbm_release_ring and passed into
ath12k_hal_rx_msdu_link_desc_set(), where it is converted again.
This double conversion is both strange and inefficient.
In ath12k_hal_rx_msdu_link_desc_set(), only buf_addr_info is actually
used. To simplify the code and improve readability, directly passes
buf_addr_info when calling ath12k_dp_rx_link_desc_return().
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Kang Yang <kang.yang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250421023444.1778-10-kang.yang@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, HAL_RX_MSDU_PKT_LENGTH_GET uses u32_get_bits to obtain the
MSDU length from the MSDU description.
This is not right. Because all halphy descriptions are little endian.
So use le32_get_bits for HAL_RX_MSDU_PKT_LENGTH_GET.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Kang Yang <kang.yang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250421023444.1778-9-kang.yang@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
WCN7850 uses monitor status ring to store status buffer. Status buffer
contains many TLVs such as MPDU START/END. From these TLVs, can get
necessary information about related payload, such as PPDU ID.
Add helper function to reap status buffer from monitor status ring so
that can parse TLVs later by ath12k_dp_mon_parse_rx_dest().
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Kang Yang <kang.yang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250421023444.1778-8-kang.yang@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Monitor status ring interrupt is configured in previous patch. So add
handler function __ath12k_dp_mon_process_ring() for monitor mode.
Will implement detail processing in patch 7 and 10.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Kang Yang <kang.yang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250421023444.1778-7-kang.yang@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The monitor mode design is:
1. Hardware captures packets on the air.
2. Hardware stores the packets into related rings.
3. When the ring buffer reaches the interrupt threshold, it triggers
the interrupt.
4. Reap and process the ring buffer in ath12k_dp_service_srng().
Here the interrupt thresholds are intr_timer_thres_us, low_threshold and
intr_batch_cntr_thres_entries. An interrupt will be triggered once:
1. Number of packets in the ring reaches intr_batch_cntr_thres_entries.
2. Number of packets in the ring reaches low_threshold(by timer).
3. Timer reaches intr_timer_thres_us.
So, add interrupt configuration for the mon status ring, then start
to process ring buffers when the interrupt arrives.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Kang Yang <kang.yang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250421023444.1778-6-kang.yang@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
For WCN7850, it doesn't have an RX MON component(RX MON dest ring and
RX MON buffer ring). So it can only reuse the mon status ring, RX
refill ring, and error dst ring for monitor mode.
Every time the hardware captures a packet, it will store status
information into the status ring and store the MSDU payload buffer
address into the error dst ring. When host reaps the MSDU payload and
consumes a buffer, it will replenish the RX refill ring to indicate a
new buffer.
The configuration of the error dst/RX ring already exists. But there is
no configuration for mon status ring. So add ring configuration for it.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Kang Yang <kang.yang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250421023444.1778-5-kang.yang@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, the hw_srng_config_template does not have a template for mon
status ring.
But srng config template is necessary during ring initialization. So add
a template for mon status ring.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Kang Yang <kang.yang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250421023444.1778-4-kang.yang@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
WCN7850 doesn't have RX MON component. So it's monitor mode design is
quite different from AP based chips like QCN9274, which have RX MON
component.
ath12k_dp_mon_parse_rx_dest_tlv() is such a specific function for AP based
chips.
So don't call this function for WCN7850.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Kang Yang <kang.yang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250421023444.1778-3-kang.yang@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, error bitmap and decap format are parsed in
ath12k_dp_mon_parse_rx_dest_tlv(). Then stored into dp_rx_mon_mpdu_list.
ath12k_dp_mon_parse_rx_dest_tlv() and dp_rx_mon_mpdu_list are only used
by QCN9274.
For WCN7850, error bitmap and decap format are also needed. So need to
parse MSDU END TLV in ath12k_dp_mon_rx_parse_status_tlv(), this is the
common function for WCN7850 and QCN9274. Then store error bitmap and
decap format so that QCN9274 can fetch them when processing MSDU payload.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Kang Yang <kang.yang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250421023444.1778-2-kang.yang@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, when ath12k performs the remove link interface operation, if
there is an ongoing scan operation on the arvif, ath12k may execute the
remove link interface operation multiple times on the same arvif. This
occurs because, during the remove link operation, if a scan operation is
present on the arvif, ath12k may receive a WMI_SCAN_EVENT_COMPLETED event
from the firmware. Upon receiving this event, ath12k will continue to
execute the ath12k_scan_vdev_clean_work() function, performing the remove
link interface operation on the same arvif again.
To address this issue, before executing the remove link interface
operation, ath12k needs to check if there is an ongoing scan operation on
the current arvif. If such an operation exists, it should be aborted.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Tested-by: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250418064008.7172-1-quic_lingbok@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
When station is connected to a 6 GHz AP, there are 2 ways to configure the
power limit to firmware. The first way is to send 2 WMI commands
WMI_PDEV_PARAM_TXPOWER_LIMIT2G/WMI_PDEV_PARAM_TXPOWER_LIMIT5G to firmware,
the second way is to send WMI_VDEV_SET_TPC_POWER_CMDID to firmware which
includes more parameters for power control.
When firmware advertises WMI_TLV_SERVICE_EXT_TPC_REG_SUPPORT, it supports
WMI_VDEV_SET_TPC_POWER_CMDID, ath12k uses it to send more parameters to
firmware. As chanctx is needed to extract necessary info for this command,
save it beforehand in ath12k_mac_op_assign_vif_chanctx().
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250418-ath12k-6g-lp-vlp-v1-15-c869c86cad60@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Add the handler for WMI_VDEV_SET_TPC_POWER_CMDID, it is for 6 GHz band.
A subsequent patch will call this handler to send power parameters to
firmware.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250418-ath12k-6g-lp-vlp-v1-14-c869c86cad60@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Prepare the parameters which are needed for WMI command
WMI_VDEV_SET_TPC_POWER_CMDID. This helper will be used in a following
patch.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250418-ath12k-6g-lp-vlp-v1-13-c869c86cad60@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Save the max transmit power received in the vdev start response event from
firmware. A subsequent patch will use this to calculate the final power
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250418-ath12k-6g-lp-vlp-v1-12-c869c86cad60@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The Transmit Power Envelope element conveys the local maximum transmit
power for various transmission bandwidths, this element is present in
various frames, e.g. beacon and probe response etc, transmitted by AP.
A station shall determine a local maximum transmit power from it.
So parse and save them for later use.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250418-ath12k-6g-lp-vlp-v1-11-c869c86cad60@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently the power spectral density (PSD) report from firmware is ignored.
Since it is needed by cfg80211, report it in struct ieee80211_reg_rule such
that cfg80211 can use it.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250418-ath12k-6g-lp-vlp-v1-10-c869c86cad60@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Once connection to AP established we know the exact power type, it is time
to update regulatory rules based on such info.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250418-ath12k-6g-lp-vlp-v1-9-c869c86cad60@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
There are two power types for 6 GHz regulatory, one is AP, another is
client. The client power type is used for station interface, and AP
power type is used for AP/mesh point interface.
When firmware boots up, WMI_REG_CHAN_LIST_CC_EXT_EVENTID is sent from
firmware at an early stage, the interface mode is not decided at this
point, then ath12k select reg rules of AP type as default.
After interface created, ath12k needs to update reg rules to the exact
power type matching the interface type.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250418-ath12k-6g-lp-vlp-v1-8-c869c86cad60@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently interface mode is determined each time a vdev is created.
In MLO scenario where there could be multiple vdevs this is just a
waste of time.
Move related logic into a new helper ath12k_mac_determine_vdev_type()
and call it once in ath12k_mac_op_add_interface().
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250418-ath12k-6g-lp-vlp-v1-7-c869c86cad60@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently we only build regdomain when channel list event is received.
That event is received when driver boots or when a new country code is
sent to firmware. At either time we may have no information about
interface mode or AP's power type, consequently WMI_REG_INDOOR_AP is
selected. In upcoming patches we will rebuild regdomain once those
information is available. For that purpose reg info has to be
stored/refreshed each time a new channel list event is received.
The stored reg info would be freed in ath12k_reg_free() when it is not
needed.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250418-ath12k-6g-lp-vlp-v1-6-c869c86cad60@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The reg info is allocated in ath12k_reg_chan_list_event() but validated
in ath12k_reg_handle_chan_list(). Currently this is good since reg info
would be freed regardless of validation results. However in an upcoming
patch the reg info might need to be stored for later use if the result
is good. Since we can not tell the result from return value of
ath12k_reg_handle_chan_list(), we need to move validation out of it.
Add a new helper ath12k_reg_validate_reg_info() and call it in
ath12k_reg_chan_list_event(), based on the result we can choose to store
or free it in the following patch.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250418-ath12k-6g-lp-vlp-v1-5-c869c86cad60@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
For 6 GHz band, firmware offers 3 types of regulatory rules for AP
mode and 6 for station mode in WMI_REG_CHAN_LIST_CC_EXT_EVENTID event.
In ath12k_reg_build_regd() current code by default chooses
WMI_REG_INDOOR_AP type rules from AP mode reg list to build regdomain,
regardless of the interface mode and power type, hence is not correct.
Pass interface mode (wmi_vdev_type) and AP power type
(ieee80211_ap_reg_power) as new arguments to ath12k_reg_build_regd()
such that we can choose correct rules based on them. Currently
ath12k_reg_build_regd() is called only by ath12k_reg_chan_list_event()
when driver boots, at that time these two arguments are not determined
yet, hence by default pass WMI_VDEV_TYPE_UNSPEC and
IEEE80211_REG_UNSET_AP, this results in WMI_REG_INDOOR_AP being chosen
at last. In upcoming patches the rules would be updated when these two
arguments could be determined.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250418-ath12k-6g-lp-vlp-v1-4-c869c86cad60@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently we pass intersect flag to tell ath12k_reg_build_regd() whether
regulatory rulse are intersected. This flag is determined in
ath12k_reg_handle_chan_list() and has no other users.
Move related logic into ath12k_reg_build_regd() to make code clear. Also
relocate ath12k_reg_is_world_alpha() to avoid forward declaration, and
refine it for code simplicity.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250418-ath12k-6g-lp-vlp-v1-3-c869c86cad60@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
ath12k_reg_chan_list_event() is doing quite some work: allocate/free
reg_info, parse chan list event and store required info in reg_info,
process reg_info, build regd and queue work item for later processing
etc, which makes it hard to read.
Refactor this function:
1. extract reg_info processing and regd building into a new helper
ath12k_reg_handle_chan_list().
2. extract reg_info free into a new helper ath12k_reg_reset_reg_info().
Note the refactor also benefit some upcoming patches where these helpers
are getting called.
Also relocate these two helpers and the existing
ath12k_reg_is_world_alpha() to reg.c to reflect what they are doing.
And update fw to firmware while relocating.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250418-ath12k-6g-lp-vlp-v1-2-c869c86cad60@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
spin_lock/spin_unlock are used in ath12k_reg_chan_list_event
to acquire/release ab->base_lock. For now this is safe because
that function is only called in soft IRQ context.
But ath12k_reg_chan_list_event() will be called from process
context in an upcoming patch, and this can result in a deadlock
if ab->base_lock is acquired in process context and then soft
IRQ occurs on the same CPU and tries to acquire that lock.
Fix it by using spin_lock_bh and spin_unlock_bh instead.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250418-ath12k-6g-lp-vlp-v1-1-c869c86cad60@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently mon reap timer is not used, and it is not needed anymore for
WCN7850.
So remove related code.
This change does not affect QCN9274, as the mon reap timer is not used
for QCN9274.
Signed-off-by: Kang Yang <kang.yang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250416022011.1935-1-kang.yang@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Now some chips which support 'support_dual_stations' will enable DBS,
but will disable DFS. Restructure the ath11k_mac_setup_iface_combinations
function to support DBS and DFS compatibility.
About 'support_dual_station' feature can refer:
https://msgid.link/20230714023801.2621802-2-quic_cjhuang@quicinc.com
Add a ieee80211_iface_combination to support DBS and DFS compatibility,
one combination can support DFS(same with non dual sta), another
combination can support DBS. When running different scenarios that will
use different ieee80211_iface_combination due to mac80211 will go through
all of possible interface combinations.
In addition, maximum number of interfaces of these types should be total
allowed in this group.
The chips affected are:
QCA6390 hw2.0
WCN6855 hw2.0
WCN6855 hw2.1
Other chips are not affected.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-00410-QCAHKSWPL_SILICONZ-2
Tested-on: IPQ6018 hw1.0 AHB WLAN.HK.2.1.0.1-01161-QCAHKSWPL_SILICONZ-1
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-04402-QCAHSPSWPL_V1_V2_SILICONZ_IOE-1.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-05266-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Yu Zhang (Yuriy) <quic_yuzha@quicinc.com>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Tested-by: Mihai Moldovan <ionic@ionic.de>
Link: https://patch.msgid.link/20241127022742.4016870-1-quic_yuzha@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Add the missing memory barrier to make sure that the REO dest ring
descriptor is read after the head pointer to avoid using stale data on
weakly ordered architectures like aarch64.
This may fix the ring-buffer corruption worked around by commit
f9fff67d2d ("wifi: ath11k: Fix SKB corruption in REO destination
ring") by silently discarding data, and may possibly also address user
reported errors like:
ath11k_pci 0006:01:00.0: msdu_done bit in attention is not set
Tested-on: WCN6855 hw2.1 WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.41
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Cc: stable@vger.kernel.org # 5.6
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218005
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Clayton Craft <clayton@craftyguy.net>
Link: https://patch.msgid.link/20250321145302.4775-1-johan+linaro@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Users of the Lenovo ThinkPad X13s have reported that Wi-Fi sometimes
breaks and the log fills up with errors like:
ath11k_pci 0006:01:00.0: HTC Rx: insufficient length, got 1484, expected 1492
ath11k_pci 0006:01:00.0: HTC Rx: insufficient length, got 1460, expected 1484
which based on a quick look at the driver seemed to indicate some kind
of ring-buffer corruption.
Miaoqing Pan tracked it down to the host seeing the updated destination
ring head pointer before the updated descriptor, and the error handling
for that in turn leaves the ring buffer in an inconsistent state.
Add the missing memory barrier to make sure that the descriptor is read
after the head pointer to address the root cause of the corruption while
fixing up the error handling in case there are ever any (ordering) bugs
on the device side.
Note that the READ_ONCE() are only needed to avoid compiler mischief in
case the ring-buffer helpers are ever inlined.
Tested-on: WCN6855 hw2.1 WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.41
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218623
Link: https://lore.kernel.org/20250310010217.3845141-3-quic_miaoqing@quicinc.com
Cc: Miaoqing Pan <quic_miaoqing@quicinc.com>
Cc: stable@vger.kernel.org # 5.6
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Miaoqing Pan <quic_miaoqing@quicinc.com>
Tested-by: Steev Klimaszewski <steev@kali.org>
Tested-by: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
Tested-by: Clayton Craft <clayton@craftyguy.net>
Link: https://patch.msgid.link/20250321094916.19098-1-johan+linaro@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Firmware requests 2 segments at first. The first segment is of 6799360
whose allocation fails due to dma remapping not available. The success
is returned to firmware. Then firmware asks for 22 smaller segments
instead of 2 big ones. Those get allocated successfully. At suspend/
hibernation time, these segments aren't freed as they will be reused
by firmware after resuming.
After resuming, the firmware asks for the 2 segments again with the
first segment of 6799360 size. Since chunk->vaddr is not NULL, the
type and size are compared with the previous type and size to know if
it can be reused or not. Unfortunately, it is detected that it cannot
be reused and this first smaller segment is freed. Then we continue to
allocate 6799360 size memory which fails and ath11k_qmi_free_target_mem_chunk()
is called which frees the second smaller segment as well. Later success
is returned to firmware which asks for 22 smaller segments again. But
as we had freed 2 segments already, we'll allocate the first 2 new
smaller segments again and reuse the remaining 20. Hence 20 small
segments are being reused instead of 22.
Add skip logic when vaddr is set, but size/type don't match. Use the
same skip and success logic as used when dma_alloc_coherent() fails.
By skipping, the possibility of resume failure due to kernel failing to
allocate memory for QMI can be avoided.
kernel: ath11k_pci 0000:03:00.0: failed to allocate dma memory for qmi (524288 B type 1)
ath11k_pci 0000:03:00.0: failed to allocate qmi target memory: -22
Tested-on: WCN6855 WLAN.HSP.1.1-03926.13-QCAHSPSWPL_V2_SILICONZ_CE-2.52297.6
Signed-off-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250428080242.466901-1-usama.anjum@collabora.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Simplifies probe slightly and adds extra error codes.
Switching from devm_ioremap to the platform variant ends up calling
devm_request_mem_region, which reserves the memory region for the
various wmacs. Per board, there is only one wmac and after some fairly
thorough analysis, there are no overlapping memory regions between wmacs
and other devices on the ahb.
Tested on a TP-Link Archer C7v2.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://patch.msgid.link/20250421040044.44887-1-rosenp@gmail.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Structures defined in hw.c are not modified in this driver.
Constifying these structures moves some data to a read-only section, so
increase overall security.
On a x86_64, with allmodconfig:
Before:
======
text data bss dec hex filename
10357 951 0 11308 2c2c drivers/net/wireless/ath/ath10k/hw.o
After:
=====
text data bss dec hex filename
11125 203 0 11328 2c40 drivers/net/wireless/ath/ath10k/hw.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/504b4d5276d13f5f9c3bffcfdaf244006312c22b.1745051315.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
There is a spelling mistake in a ath10k_warn message. Fix it and
remove space before colon to tidy up message.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://patch.msgid.link/20250418115627.534833-1-colin.i.king@gmail.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
According to the code documentation in ath12k_mac_op_hw_scan(), "if no
links of an ML VIF are already active on the radio corresponding to the
given scan frequency, the scan link (link ID 15) should be used". This rule
should apply to non-ML interfaces as well to maintain uniformity across the
driver. However, currently, link 0 is selected as the scan link during
non-ML operations.
Update the code to use scan link ID 15 in all cases.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250417-fix_scan_vdev_handling-v3-2-9ec42513d26b@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
For scanning purposes, the driver can use link ID 15 (scan link). A future
change will make non-ML interfaces to select the scan link. In this
scenario, arvif->link_id will be used to retrieve the link configuration in
ath12k_mac_vdev_create(). However, link ID 15 is not recognized as a valid
link ID in the upper kernel, which will result in a failure to fetch
link_conf and subsequently cause the scan to fail.
To avoid this issue, ensure link_conf is fetched only when the link ID is
within the valid range. Since link_conf cannot be retrieved using the scan
link, use vif->addr as the Ethernet address for creating the scan vdev.
This address will serve as the source address (address 2) in the probe
request frames during scanning. Additionally, use the automatic Tx power
value for the vdev. As this is a scan vdev, these values do not affect the
scan functionality.
Note that vif->addr will only be taken when a valid link_conf can not be
fetched. Otherwise, link_conf's address will be taken as address 2.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250417-fix_scan_vdev_handling-v3-1-9ec42513d26b@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Read the country code from SMBIOS and send it to the firmware. The
firmware will then indicate the regulatory domain information for
the country code, which ath12k will use.
dmesg:
[ 1242.637253] ath12k_pci 0000:02:00.0: worldwide regdomain setting from SMBIOS
[ 1242.637259] ath12k_pci 0000:02:00.0: bdf variant name not found.
[ 1242.637261] ath12k_pci 0000:02:00.0: SMBIOS bdf variant name not set.
[ 1242.927543] ath12k_pci 0000:02:00.0: set current country pdev id 0 alpha2 00
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-02582-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kang Yang <kang.yang@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250417024227.1712-1-kang.yang@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
ath12k:
Enable AHB support for IPQ5332.
Add monitor interface support to QCN9274.
Add MLO support to WCN7850.
Add 802.11d scan offload support to WCN7850.
ath11k:
Restore hibernation support
In addition, perform the usual set of bug fixes and cleanups across
all supported drivers.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQ/mtSHzPUi16IfDEksFbugiYzLewUCaAJ2WAAKCRAsFbugiYzL
exnBAQDcBNn9WWQnHOIo4YIY//8Rnw311troRh1V/NLNHTaMmAD9G8SCa8qbI/rs
gOxcP5XeDmR3LwKuw4/7emXucX9W+ww=
=mAEA
-----END PGP SIGNATURE-----
Merge tag 'ath-next-20250418' of git://git.kernel.org/pub/scm/linux/kernel/git/ath/ath into wireless-next
Jeff Johnson says:
====================
ath.git patches for v6.16
ath12k:
Enable AHB support for IPQ5332.
Add monitor interface support to QCN9274.
Add MLO support to WCN7850.
Add 802.11d scan offload support to WCN7850.
ath11k:
Restore hibernation support
In addition, perform the usual set of bug fixes and cleanups across
all supported drivers.
====================
Change-Id: I6555e64d7434f3a5fed5faab25057be93106b18e
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For MBSSID, each vif (struct ieee80211_vif) stores another vif
pointer for the transmitting profile of MBSSID set. This won't
suffice for MLO as there may be multiple links, each of which can
be part of different MBSSID sets. Hence the information needs to
be stored per-link. Additionally, the transmitted profile itself
may be part of an MLD hence storing vif will not suffice either.
Fix MLO by storing an instance of struct ieee80211_bss_conf
for each link.
Modify following operations to reflect the above structure updates:
- channel switch completion
- BSS color change completion
- Removing nontransmitted links in ieee80211_stop_mbssid()
- drivers retrieving the transmitted link for beacon templates.
Signed-off-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Co-developed-by: Muna Sinada <muna.sinada@oss.qualcomm.com>
Signed-off-by: Muna Sinada <muna.sinada@oss.qualcomm.com>
Co-developed-by: Aloka Dixit <aloka.dixit@oss.qualcomm.com>
Signed-off-by: Aloka Dixit <aloka.dixit@oss.qualcomm.com>
Link: https://patch.msgid.link/20250408184501.3715887-3-aloka.dixit@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Jason mentioned at netdevconf that we've run out of tx_flags in
the skb_shinfo(). Gain one bit back by removing the wifi bit.
We can do that because the only userspace application for it
(hostapd) doesn't change the setting on the socket, it just
uses different sockets, and normally doesn't even use this any
more, sending the frames over nl80211 instead.
Reviewed-by: Jason Xing <kerneljasonxing@gmail.com>
Link: https://patch.msgid.link/20250313134942.52ff54a140ec.If390bbdc46904cf451256ba989d7a056c457af6e@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the past %pK was preferable to %p as it would not leak raw pointer
values into the kernel log.
Since commit ad67b74d24 ("printk: hash addresses printed with %p")
the regular %p has been improved to avoid this issue.
Furthermore, restricted pointers ("%pK") were never meant to be used
through printk(). They can still unintentionally leak raw pointers or
acquire sleeping looks in atomic contexts.
Switch to the regular pointer formatting which is safer and
easier to reason about.
There are still a few users of %pK left, but these use it through seq_file,
for which its usage is safe.
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Acked-by: Loic Poulain <loic.poulain@oss.qualcomm.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Link: https://patch.msgid.link/20250417-restricted-pointers-ath-v1-4-4e9a04dbe362@linutronix.de
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In the past %pK was preferable to %p as it would not leak raw pointer
values into the kernel log.
Since commit ad67b74d24 ("printk: hash addresses printed with %p")
the regular %p has been improved to avoid this issue.
Furthermore, restricted pointers ("%pK") were never meant to be used
through printk(). They can still unintentionally leak raw pointers or
acquire sleeping looks in atomic contexts.
Switch to the regular pointer formatting which is safer and
easier to reason about.
There are still a few users of %pK left, but these use it through seq_file,
for which its usage is safe.
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Link: https://patch.msgid.link/20250417-restricted-pointers-ath-v1-3-4e9a04dbe362@linutronix.de
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In the past %pK was preferable to %p as it would not leak raw pointer
values into the kernel log.
Since commit ad67b74d24 ("printk: hash addresses printed with %p")
the regular %p has been improved to avoid this issue.
Furthermore, restricted pointers ("%pK") were never meant to be used
through printk(). They can still unintentionally leak raw pointers or
acquire sleeping looks in atomic contexts.
Switch to the regular pointer formatting which is safer and
easier to reason about.
There are still a few users of %pK left, but these use it through seq_file,
for which its usage is safe.
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Link: https://patch.msgid.link/20250417-restricted-pointers-ath-v1-2-4e9a04dbe362@linutronix.de
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In the past %pK was preferable to %p as it would not leak raw pointer
values into the kernel log.
Since commit ad67b74d24 ("printk: hash addresses printed with %p")
the regular %p has been improved to avoid this issue.
Furthermore, restricted pointers ("%pK") were never meant to be used
through printk(). They can still unintentionally leak raw pointers or
acquire sleeping looks in atomic contexts.
Switch to the regular pointer formatting which is safer and
easier to reason about.
There are still a few users of %pK left, but these use it through seq_file,
for which its usage is safe.
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Link: https://patch.msgid.link/20250417-restricted-pointers-ath-v1-1-4e9a04dbe362@linutronix.de
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In current WLAN recovery code flow, ath12k_core_halt() only reinitializes
the "arvifs" list head. This will cause the list node immediately following
the list head to become an invalid list node. Because the prev of that node
still points to the list head "arvifs", but the next of the list head
"arvifs" no longer points to that list node.
When a WLAN recovery occurs during the execution of a vif removal, and it
happens before the spin_lock_bh(&ar->data_lock) in
ath12k_mac_vdev_delete(), list_del() will detect the previously mentioned
situation, thereby triggering a kernel panic.
The fix is to remove and reinitialize all vif list nodes from the list head
"arvifs" during WLAN halt. The reinitialization is to make the list nodes
valid, ensuring that the list_del() in ath12k_mac_vdev_delete() can execute
normally.
Call trace:
__list_del_entry_valid_or_report+0xd4/0x100 (P)
ath12k_mac_remove_link_interface.isra.0+0xf8/0x2e4 [ath12k]
ath12k_scan_vdev_clean_work+0x40/0x164 [ath12k]
cfg80211_wiphy_work+0xfc/0x100
process_one_work+0x164/0x2d0
worker_thread+0x254/0x380
kthread+0xfc/0x100
ret_from_fork+0x10/0x20
The change is mostly copied from the ath11k patch:
https://lore.kernel.org/all/20250320053145.3445187-1-quic_stonez@quicinc.com/
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: Maharaja Kennadyrajan <maharaja.kennadyrajan@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250416021724.2162519-1-maharaja.kennadyrajan@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
ath12k_mac_mgmt_tx_wmi() fetches ath12k's skb_cb space multiple times from
TX skb which is redundant operation. Save the skb_cb in a local pointer
and use the same instead.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250415195812.2633923-3-rameshkumar.sundaram@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently for CCMP256, GCMP128 and GCMP256 ciphers, in
ath12k_install_key() IEEE80211_KEY_FLAG_GENERATE_IV_MGMT is not set and
in ath12k_mac_mgmt_tx_wmi() a length of IEEE80211_CCMP_MIC_LEN is reserved
for all ciphers.
This results in unexpected drop of protected management frames in case
either of above 3 ciphers is used. The reason is, without
IEEE80211_KEY_FLAG_GENERATE_IV_MGMT set, mac80211 will not generate
CCMP/GCMP headers in TX frame for ath12k.
Also MIC length reserved is wrong and such frames are dropped by hardware.
Fix this by setting IEEE80211_KEY_FLAG_GENERATE_IV_MGMT flag for above
ciphers and by reserving proper MIC length for those ciphers.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250415195812.2633923-2-rameshkumar.sundaram@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, in the mac80211 layer, received EAPOL packets are dropped
when the HT control field is present in the QoS header. This issue
arises due to an incorrect QoS control field offset used to build
the QoS header in the MSDU data, leading to a corrupted header in the
mac80211 layer. This issue also applies to other frames that contain
the QoS control field, such as QoS data or Null frames. To resolve
this, use ieee80211_get_qos_ctl() to obtain the correct QoS control
offset from the MSDU data. Additionally, ensure the QoS control header
is copied in little-endian format within the MSDU data.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: Ramasamy Kaliappan <quic_rkaliapp@quicinc.com>
Signed-off-by: Nithyanantham Paramasivam <nithyanantham.paramasivam@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250415184102.2707300-1-nithyanantham.paramasivam@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, driver allocates the struct ath12k_rx_peer_stats for each
station regardless of whether ext_rx_stats is enabled. This structure
is populated by the monitor destination ring for both single-user and
multi-user scenarios when ext_rx_stats is enabled. However, when
ext_rx_stats is disabled, this allocation is unnecessary and results in
additional memory consumption.
To address this issue, allocate the struct ath12k_rx_peer_stats only when
ext_rx_stats is enabled through debugfs. This change prevents unnecessary
memory allocation. Additionally, ensure that the station dump RSSI is
updated irrespective of the ext_rx_stats enablement.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: P Praneesh <praneesh.p@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250409052647.81955-1-praneesh.p@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Running this test in a loop it is easy to reproduce an rtnl deadlock:
iw reg set FI
ifconfig wlan0 down
What happens is that thread A (workqueue) tries to update the regulatory:
try to acquire the rtnl_lock of ar->regd_update_work
rtnl_lock
ath12k_regd_update [ath12k]
ath12k_regd_update_work [ath12k]
process_one_work
worker_thread
kthread
ret_from_fork
And thread B (ifconfig) tries to stop the interface:
try to cancel_work_sync(&ar->regd_update_work) in ath12k_mac_op_stop().
ifconfig 3109 [003] 2414.232506: probe:
ath12k_mac_op_stop [ath12k]
drv_stop [mac80211]
ieee80211_do_stop [mac80211]
ieee80211_stop [mac80211]
The sequence of deadlock is:
1. Thread B calls rtnl_lock().
2. Thread A starts to run and calls rtnl_lock() from within
ath12k_regd_update_work(), then enters wait state because the lock is
owned by thread B.
3. Thread B tries to call cancel_work_sync(&ar->regd_update_work), but
thread A is in ath12k_regd_update_work() waiting for rtnl_lock(). So
cancel_work_sync() forever waits for ath12k_regd_update_work() to
finish and we have a deadlock.
Change to use regulatory_set_wiphy_regd(), which is the asynchronous
version of regulatory_set_wiphy_regd_sync(). This way rtnl & wiphy locks
are not required so can be removed, and in the end the deadlock issue can
be avoided.
But a side effect introduced by the asynchronous regd update is that,
some essential information used in ath12k_reg_update_chan_list(), which
would be called later in ath12k_regd_update(), might has not been updated
by cfg80211, as a result wrong channel parameters sent to firmware.
To handle this side effect, move ath12k_reg_update_chan_list() to
ath12k_reg_notifier(), and advertise WIPHY_FLAG_NOTIFY_REGDOM_BY_DRIVER
to cfg80211. This works because, in the process of the asynchronous regd
update, after the new regd is processed, cfg80211 will notify ath12k by
calling ath12k_reg_notifier(). Since all essential information is updated
at that time, we are good to do channel list update.
Please note ath12k_reg_notifier() could also be called due to other
reasons, like core/beacon/user hints etc. For them we are not allowed to
call ath12k_reg_update_chan_list() because regd has not been updated.
This is done by verifying the initiator.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Co-developed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Reviewed-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250408-rtnl-deadlock-v3-1-fdc12bc511ea@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In the WBM error path, while processing TKIP MIC errors, MSDU length
is fetched from the hal_rx_desc's msdu_end. This MSDU length is
directly passed to skb_put() without validation. In stress test
scenarios, the WBM error ring may receive invalid descriptors, which
could lead to an invalid MSDU length.
To fix this, add a check to drop the skb when the calculated MSDU
length is greater than the skb size.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: Nithyanantham Paramasivam <nithyanantham.paramasivam@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250416021903.3178962-1-nithyanantham.paramasivam@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In ath12k_dp_rx_msdu_coalesce(), rxcb is fetched from skb and boolean
is_continuation is part of rxcb.
Currently, after freeing the skb, the rxcb->is_continuation accessed
again which is wrong since the memory is already freed.
This might lead use-after-free error.
Hence, fix by locally defining bool is_continuation from rxcb,
so that after freeing skb, is_continuation can be used.
Compile tested only.
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: Sarika Sharma <quic_sarishar@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250408045327.1632222-1-quic_sarishar@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, RX is_mcbc bit is set for packets sent from client as
destination address (DA) is multicast/broadcast address, but packets
are actually unicast as receiver address (RA) is not multicast address.
Hence, packets are not handled properly due to this is_mcbc bit.
Therefore, reset the is_mcbc bit if interface type is AP.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sarika Sharma <quic_sarishar@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250411061523.859387-3-quic_sarishar@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, the RX multicast broadcast packet check is performed using
bit 15 from the info6 field of the MPDU start descriptor. This check
can also be done using bit 9 from the info5 field of the MSDU end
descriptor. However, in some scenarios multicast bit is not set when
fetched from MPDU start descriptor.
Therefore, checking the RX multicast broadcast packet from the MSDU
end descriptor is more reliable as it is per MSDU.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sarika Sharma <quic_sarishar@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250411061523.859387-2-quic_sarishar@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
During the hardware register, driver updates the frequency range
during boot-up. However, if new regulatory rules are applied after
boot-up, the frequency range remains based on the older rules.
Since different countries have varying regulatory rules, the
frequency range can differ. Retaining the frequency range based on
outdated rules can be misleading.
Update the frequency range according to the new regulatory rules in
the function ath12k_regd_update().
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Co-developed-by: Rajat Soni <quic_rajson@quicinc.com>
Signed-off-by: Rajat Soni <quic_rajson@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250408042128.720263-4-quic_rajson@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
During the initial WMI exchange, the firmware updates the
hardware-supported start and end frequencies in the
ath12k_wmi_hal_reg_capabilities_ext_arg structure. These frequencies,
being hardware-supported, may not always align with the current
regulatory operating frequencies. When operating as multiple grouped
hardwares under a single wiphy, the driver advertises these values
directly to the upper layer in the per-radio frequency range,
which can be misleading.
Sample output snippet from iw phyX info command -
[..]
Supported wiphy radios:
* Idx 0:
Frequency Range: 2312 MHz - 2732 MHz
[..]
* Idx 1:
Frequency Range: 5150 MHz - 5330 MHz
[..]
[..]
The frequency range displayed above is incorrect because the driver
directly advertises the hardware-supported values to the upper layer.
The driver is aware of the current operating regulatory rules, and
hence it can use this information to determine the final operating
start and end frequencies.
To resolve this issue, add support to store the start and end
frequencies received during the regulatory update event.
Then, intersect these with the hardware-supported start and
end frequencies, and finally, advertise the intersected values to the
upper layer.
Sample output snippet from iw phyX info command after the fix -
[..]
Supported wiphy radios:
* Idx 0:
Frequency Range: 2402 MHz - 2472 MHz
[..]
* Idx 1:
Frequency Range: 5170 MHz - 5330 MHz
[..]
[..]
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Co-developed-by: Rajat Soni <quic_rajson@quicinc.com>
Signed-off-by: Rajat Soni <quic_rajson@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250408042128.720263-3-quic_rajson@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In a subsequent change, the frequency range needs to be updated with
each regulatory update. Since the current function also modifies the
DISABLED flag in the actual channel list, which should always align
with hardware-supported start and end frequencies rather than the
current operating ones, the existing function cannot be called again.
Therefore, the logic for setting the frequency range needs to be
refactored.
To address this, refactor the frequency setting part into a new
helper function, ath12k_mac_update_freq_range(). Since this needs
to be done independently of updating the DISABLED flag, call the new
helper function ath12k_mac_update_freq_range() after updating the
channel list for each band.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Rajat Soni <quic_rajson@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250408042128.720263-2-quic_rajson@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
During dma_unmap_single() for extended skb, the driver currently uses
sizeof() of the corresponding structure. When the allocation size changes,
one of the parameters of dma_unmap_single() needs to be updated everywhere.
Improve code readability by using skb->len instead of sizeof() the structure.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: P Praneesh <praneesh.p@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250411060154.1388159-5-praneesh.p@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In ath12k_dp_tx(), memory allocated for extended skb is not freed
properly, causing a memory leak even when the host receives tx
completion for those skbs. Fix this issue by storing skb_ext_desc
in the host tx descriptor and using this skb_ext_desc field during
completion or during ath12k_dp_cc_cleanup().
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: P Praneesh <praneesh.p@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250411060154.1388159-4-praneesh.p@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Current code uses mac_id and msdu parameters in ath12k_dp_tx_free_txbuf()
and ath12k_dp_tx_process_htt_tx_complete(). Since these parameters are
already encapsulated by struct ath12k_dp_tx_desc, passing them individually
results in redundant arguments.
Introduce struct ath12k_tx_desc_params to capture the skb, mac_id, and pass
it to the corresponding functions. Refactor these functions to use struct
ath12k_tx_desc_params instead, reducing the number of arguments and improving
function argument handling efficiency. Additionally, use struct
ath12k_tx_desc_params in ath12k_dp_tx_htt_tx_complete_buf() and
ath12k_dp_tx_complete_msdu(), which will be utilized for fetching extended skb
in a future patch.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: P Praneesh <praneesh.p@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250411060154.1388159-3-praneesh.p@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, in the case of extended skb allocation, the buffer is freed
before the DMA unmap operation. This premature deletion can result in
skb->data corruption, as the memory region could be re-allocated for other
purposes. Fix this issue by reordering the failure cases by calling
dma_unmap_single() first, then followed by the corresponding kfree_skb().
This helps avoid data corruption in case of failures in dp_tx().
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: P Praneesh <praneesh.p@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250411060154.1388159-2-praneesh.p@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
For single pdev device, radio number of a device is forced as 1 in
ath12k_wmi_ext_soc_hal_reg_caps_parse(). This leads to ah->num_radio == 1
and then in ath12k_mac_setup_iface_combinations() we report to
mac/cfg80211 that only 1 channel is supported. In MLO case, it finally
results in failing to bring up the second link as it is in another
channel.
Change num_different_channels to 2 to allow a second link. Since DFS on
multiple channels are not supported yet, remove radar_detect_widths.
For now WCN7850 is the only single pdev device, so others should not be
affected.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00209-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250409-ath12k-wcn7850-mlo-support-v2-9-3801132ca2c3@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The primary link check bypasses REO queue setup for non-primary links
in ath12k_dp_rx_peer_tid_setup(), this works for QCN9274 but breaks
WCN7850 as WCN7850 needs it to be done for each link peer.
Add a new hardware parameter to differentiate them.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00209-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250409-ath12k-wcn7850-mlo-support-v2-8-3801132ca2c3@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In MLO case, all link peers share the same REO queue, so the queue
should be allocated only once, currently this is done by checking
primary_link flag in ath12k_dp_rx_peer_tid_setup(). However, the
check not only avoids duplicate allocation, but also bypasses sending
queue configuration to firmware for non-primary links. In an upcoming
patch, changes will be added to make this check no-ops for WCN7850,
as WCN7850 firmware needs to be explicitly notified each link peer's
queue configuration. That said, the duplicate allocation would arise
again after that change, hence it needs to be resolved before hand.
Since all link peers share the same queue, it should be allocated per
MLD peer, not per link peer. So change to do allocation once and save
it in MLD peer, link peers can simply get queue configuration from
there.
Also relocate ath12k_reoq_buf structure to core.h to avoid circular
dependency.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00209-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250409-ath12k-wcn7850-mlo-support-v2-7-3801132ca2c3@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently vaddr, paddr and size fields are located together with other
fields in ath12k_dp_rx_tid structure. Logically they represents the
REO queue buffer so better to group them in an individual structure.
Introduce a new structure ath12k_reoq_buf to group them. This improves
code readability, and benefits the upcoming patch where this structure
is heavily accessed.
While at it, change vaddr type to 'void *' since it is actually not
pointing to any u32 buffer. Also rename paddr as paddr_aligned to better
reflect its actual meaning.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00209-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250409-ath12k-wcn7850-mlo-support-v2-6-3801132ca2c3@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In MLO scenario WCN7850 firmware requests the assoc link to associate
before any other links. However currently in
ath12k_mac_op_vif_cfg_changed() we are doing association in an ascending
order of link id. If the assoc link does not get assigned the smallest
id, a non-assoc link gets associated first and firmware crashes.
Change to do association for the assoc link first.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00209-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250409-ath12k-wcn7850-mlo-support-v2-5-3801132ca2c3@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In MLO scenario, for station mode interface, WCN7850 firmware requests
the assoc link vdev to get started before any other link vdevs starts.
Firmware internally checks assoc_link field of
wmi_vdev_start_mlo_params.flags when the first vdev starts. And if the
check fails firmware crashes.
Current connection flow guarantees the assoc link vdev gets started
first (at assoc stage only one link vdev is created/started, i.e. the
assoc link vdev), however the assoc_link flag is never set, resulting
in WCN7850 firmware crash.
Note ath12k_link_sta structure already has is_assoc_link flag, and it
is properly set for assoc link. However we can not use it because it
won't be available before peer gets created, which is too late for vdev
starts.
So add a new flag 'is_sta_assoc_link' in ath12k_link_vif structure and
set it when deflink vdev is created. This is valid because we always
use deflink as the assoc link. This flag is passed to firmware vdev
starts to avoid firmware crash. Also verify the link vif/sta pair has
the same settings when creating link sta.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00209-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250409-ath12k-wcn7850-mlo-support-v2-4-3801132ca2c3@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently firmware MLO capability is validated via firmware IE, however
WCN7850 firmware does not support this method but instead advertises
MLO by single_chip_mlo_support bit in QMI phy capability message.
Change to consider single_chip_mlo_support bit as well for MLO capability
validation.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00209-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250409-ath12k-wcn7850-mlo-support-v2-3-3801132ca2c3@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently fw_features is used to check if a specific feature is supported
or not: if the feature bit is set the feature is believed to be supported,
otherwise not supported. Since fw_features is populated only when using
firmware API-2, and by default it is zero, in case of API-1 such as
WCN7850 firmware it is possible that a feature is not enabled by host
while actually firmware supports it.
To avoid this, add a new flag indicating whether fw_features has been ever
populated or not, and only when that flag is true we choose to believe
fw_features. This benefits firmware MLO capability validation in an
upcoming patch.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00209-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250409-ath12k-wcn7850-mlo-support-v2-2-3801132ca2c3@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
There are several places checking if a specific bit set in
ab->fw.fw_features, and in an upcoming patch additional check needs to be
added at all places.
Introduce a new helper ath12k_fw_feature_supported() to avoid code
duplication.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00209-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250409-ath12k-wcn7850-mlo-support-v2-1-3801132ca2c3@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
When operating with multiple devices grouped together, the firmware stores
data related to the state machine of each partner device in the MLO global
memory region. If the firmware crashes, it updates the state to 'crashed'.
During recovery, this memory is shared with the firmware again, and upon
detecting the 'crashed' state, it reasserts. This leads to a loop of
firmware asserts and it never recovers.
Hence to fix this issue, once all devices in the group have been asserted
and powered down, reset the MLO global memory region.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250408-fix_reboot_issues_with_hw_grouping-v4-9-95e7bf048595@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, in ath12k_core_reset(), the device is powered up immediately
after a power down. However, with hardware grouping, when one device
asserts, all partner devices also asserts. If there is a delay in
processing these asserts, by the time this device powers up, other devices
might still be asserting, leading to an overall recovery failure.
To prevent this issue, ensure all asserts for a group are processed before
initiating the power-up sequence.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250408-fix_reboot_issues_with_hw_grouping-v4-8-95e7bf048595@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, when ath12k_core_restart() is called and the ab->is_reset flag
is set, it invokes ieee80211_restart_hw() for all hardware in the same
group. However, other hardware might still be in the recovery process,
making this call inappropriate with grouping into picture.
To address this, add a condition to check if the group is ready. If the
group is not ready, do not call ieee80211_restart_hw().
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250408-fix_reboot_issues_with_hw_grouping-v4-7-95e7bf048595@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, ath12k_core_pre_reconfigure_recovery() reconfigures all radios
within the same group. During grouping and driver going for a recovery,
this function is called as many times as there are devices in the group.
Consequently, it performs the same reconfiguration multiple times, which
is unnecessary.
To prevent this, add a check to continue if the action has already been
taken.
To simplify the management of various flags, the reason for hardware queues
being stopped is used as a check instead of introducing a new flag.
While at it, also add missing wiphy locks. Wiphy lock is required since
ath12k_mac_drain_tx() which is called by
ath12k_core_pre_reconfigure_recovery() needs this lock to be held by the
caller.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250408-fix_reboot_issues_with_hw_grouping-v4-6-95e7bf048595@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
At present, during PCI shutdown, the power down is only executed for a
single device. However, when operating in a group, all devices need to be
powered down simultaneously. Failure to do so will result in a firmware
assertion.
Hence, introduce a new ath12k_pci_hw_group_power_down() and call it during
power down. This will ensure that all partner devices are properly powered
down.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250408-fix_reboot_issues_with_hw_grouping-v4-5-95e7bf048595@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Commit a5686ae820 ("wifi: ath12k: move ATH12K_FLAG_REGISTERED handling to
ath12k_mac_register()") relocated the setting of the ATH12K_FLAG_REGISTERED
flag to the ath12k_mac_register() function. However, this function only
accesses the first device (ab) via ag->ab[0], resulting in the flag being
set only for the first device in the group. Similarly,
ath12k_mac_unregister() only unsets the flag for the first device. The flag
should actually be set for all devices in the group to avoid issues during
recovery.
Hence, move setting and clearing of this flag in the function
ath12k_core_hw_group_start() and ath12k_core_hw_group_stop() respectively.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: a5686ae820 ("wifi: ath12k: move ATH12K_FLAG_REGISTERED handling to ath12k_mac_register()")
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250408-fix_reboot_issues_with_hw_grouping-v4-4-95e7bf048595@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
With hardware grouping, during reboot, whenever a device is removed, it
powers down itself and all its partner devices in the same group. Now this
is done by all devices and hence there is multiple power down for devices
and hence the following error messages can be seen:
ath12k_pci 0002:01:00.0: failed to set mhi state POWER_OFF(3) in current mhi state (0x0)
ath12k_pci 0002:01:00.0: failed to set mhi state: POWER_OFF(3)
ath12k_pci 0002:01:00.0: failed to set mhi state DEINIT(1) in current mhi state (0x0)
ath12k_pci 0002:01:00.0: failed to set mhi state: DEINIT(1)
ath12k_pci 0003:01:00.0: failed to set mhi state POWER_OFF(3) in current mhi state (0x0)
ath12k_pci 0003:01:00.0: failed to set mhi state: POWER_OFF(3)
ath12k_pci 0003:01:00.0: failed to set mhi state DEINIT(1) in current mhi state (0x0)
ath12k_pci 0003:01:00.0: failed to set mhi state: DEINIT(1)
ath12k_pci 0004:01:00.0: failed to set mhi state POWER_OFF(3) in current mhi state (0x0)
ath12k_pci 0004:01:00.0: failed to set mhi state: POWER_OFF(3)
To prevent this, check if the ATH12K_PCI_FLAG_INIT_DONE flag is already
set before powering down. If it is set, it indicates that another partner
device has already performed the power down, and this device can skip this
step.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250408-fix_reboot_issues_with_hw_grouping-v4-3-95e7bf048595@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, driver does not manage reference counting for attaching and
detaching cores to/from hardware groups. This can lead to issues when
multiple cores are involved. Or with same core, attach/detach is called
multiple times back to back.
Fix this issue by using reference counting.
With that, it is now ensured that the core is properly attached or detached
from the hardware group and even back to back calls will not alter the
count.
Additionally, add some debug logs during the attachment and detachment
events for better debugging and tracking.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250408-fix_reboot_issues_with_hw_grouping-v4-2-95e7bf048595@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
During rmmod of ath12k module with SLUB debug enabled, following print is
seen -
=============================================================================
BUG kmalloc-1k (Not tainted): Object already free
-----------------------------------------------------------------------------
Allocated in ath12k_reg_build_regd+0x94/0xa20 [ath12k] age=10470 cpu=0 pid=0
__kmalloc_noprof+0xf4/0x368
ath12k_reg_build_regd+0x94/0xa20 [ath12k]
ath12k_wmi_op_rx+0x199c/0x2c14 [ath12k]
ath12k_htc_rx_completion_handler+0x398/0x554 [ath12k]
ath12k_ce_per_engine_service+0x248/0x368 [ath12k]
ath12k_pci_ce_workqueue+0x28/0x50 [ath12k]
process_one_work+0x14c/0x28c
bh_worker+0x22c/0x27c
workqueue_softirq_action+0x80/0x90
tasklet_action+0x14/0x3c
handle_softirqs+0x108/0x240
__do_softirq+0x14/0x20
Freed in ath12k_reg_free+0x40/0x74 [ath12k] age=136 cpu=2 pid=166
kfree+0x148/0x248
ath12k_reg_free+0x40/0x74 [ath12k]
ath12k_core_hw_group_destroy+0x68/0xac [ath12k]
ath12k_core_deinit+0xd8/0x124 [ath12k]
ath12k_pci_remove+0x6c/0x130 [ath12k]
pci_device_remove+0x44/0xe8
device_remove+0x4c/0x80
device_release_driver_internal+0x1d0/0x22c
driver_detach+0x50/0x98
bus_remove_driver+0x70/0xf4
driver_unregister+0x30/0x60
pci_unregister_driver+0x24/0x9c
ath12k_pci_exit+0x18/0x24 [ath12k]
__arm64_sys_delete_module+0x1a0/0x2a8
invoke_syscall+0x48/0x110
el0_svc_common.constprop.0+0x40/0xe0
Slab 0xfffffdffc0033600 objects=10 used=6 fp=0xffff000000cdcc00 flags=0x3fffe0000000240(workingset|head|node=0|zone=0|lastcpupid=0x1ffff)
Object 0xffff000000cdcc00 @offset=19456 fp=0xffff000000cde400
[...]
This issue arises because in ath12k_core_hw_group_destroy(), each device
calls ath12k_core_soc_destroy() for itself and all its partners within the
same group. Since ath12k_core_hw_group_destroy() is invoked for each
device, this results in a double free condition, eventually causing the
SLUB bug.
To resolve this, set the freed pointers to NULL. And since there could be
a race condition to read these pointers, guard these with the available
mutex lock.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: 6f245ea0ec ("wifi: ath12k: introduce device group abstraction")
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250408-fix_reboot_issues_with_hw_grouping-v4-1-95e7bf048595@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
If the user tries to write more than 32 bytes then it results in memory
corruption. Fortunately, this is debugfs so it's limited to root users.
Fixes: 3f73c24f28 ("wifi: ath12k: Add support to enable debugfs_htt_stats")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/35daefbd-d493-41d9-b192-96177d521b40@stanley.mountain
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The devm_memremap() function returns error pointers on error and the
ioremap() function returns NULL on error. The error checking here got
those flipped around.
Fixes: c01d5cc9b9 ("wifi: ath12k: Power up userPD")
Fixes: 6cee30f0da ("wifi: ath12k: add AHB driver support for IPQ5332")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/937abc74-9648-4c05-a2c3-8db408b3ed9e@stanley.mountain
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The use of of_property_read_u32() isn't really correct as
"memory-region" contains phandles (though those happen to be u32s. As
it is just testing for property presence, use of_property_present()
instead.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20250408190211.2505737-2-robh@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Incorrect WMI tag is used for EHT rate update from host to firmware
while encoding peer assoc WMI.
Correct the WMI tag used for EHT rate update from WMI_TAG_HE_RATE_SET
to the proper tag. This ensures firmware does not mistakenly update HE rate during parsing.
Found during code review. Compile tested only.
Fixes: 5b70ec6036 ("wifi: ath12k: add WMI support for EHT peer")
Signed-off-by: Ramya Gnanasekar <ramya.gnanasekar@oss.qualcomm.com>
Link: https://patch.msgid.link/20250409152341.944628-1-ramya.gnanasekar@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, the AP does not support the broadcast target wake time (TWT)
feature. Therefore, disable the broadcast TWT feature in the HE MAC
capabilities element field.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00209-QCAHKSWPL_SILICONZ-1
Signed-off-by: Thomas Wu <quic_wthomas@quicinc.com>
Signed-off-by: Aaradhana Sahu <aaradhana.sahu@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250409053830.4039467-1-aaradhana.sahu@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
