In rare cases, ath10k may lose connection with the PCIe bus due to
some unknown reasons, which could further lead to system crashes during
resuming due to watchdog timeout:
ath10k_pci 0000:01:00.0: wmi command 20486 timeout, restarting hardware
ath10k_pci 0000:01:00.0: already restarting
ath10k_pci 0000:01:00.0: failed to stop WMI vdev 0: -11
ath10k_pci 0000:01:00.0: failed to stop vdev 0: -11
ieee80211 phy0: PM: **** DPM device timeout ****
Call Trace:
panic+0x125/0x315
dpm_watchdog_set+0x54/0x54
dpm_watchdog_handler+0x57/0x57
call_timer_fn+0x31/0x13c
At this point, all WMI commands will timeout and attempt to restart
device. So set a threshold for consecutive restart failures. If the
threshold is exceeded, consider the hardware is unreliable and all
ath10k operations should be skipped to avoid system crash.
fail_cont_count and pending_recovery are atomic variables, and
do not involve complex conditional logic. Therefore, even if recovery
check and reconfig complete are executed concurrently, the recovery
mechanism will not be broken.
Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00288-QCARMSWPZ-1
Signed-off-by: Kang Yang <kang.yang@oss.qualcomm.com>
Reviewed-by: Loic Poulain <loic.poulain@oss.qualcomm.com>
Link: https://patch.msgid.link/20250623022731.509-1-kang.yang@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
During interface creation, following print is observed on the console -
Timeout while waiting for regulatory update
This occurs due to commit 906619a009 ("wifi: ath12k: handle regulatory
hints during mac registration"), which introduced a completion mechanism to
synchronize the regulatory update process. The intent behind this change is
to coordinate the timing between when the firmware sends regulatory data to
the driver and when the driver processes that data.
However, during interface addition, if the 6 GHz band is active, the driver
invokes ath12k_regd_update() to apply the appropriate 6 GHz power mode
regulatory settings. At this point, there is no interaction with the
firmware, so the completion object is not reinitialized. As a result,
wait_for_completion() eventually times out, leading to the observed error
log message.
Hence to fix this, move all complete() on regd_update_completed to
complete_all().
The complete() function signals only once, causing any subsequent waits
without reinitialization to timeout. In this scenario, since waiting is
unnecessary, complete_all() can be used instead, ensuring that subsequent
calls to wait without reinitialization will simply bail out and not
actually wait. This approach is ideal because if the firmware is not
involved, there is no need to wait for the completion event. However, if
the firmware is involved, it is guaranteed that the completion will be
reinitialized, and thus, it would wait.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.5-01651-QCAHKSWPL_SILICONZ-1
Tested-by: Kang Yang <kang.yang@oss.qualcomm.com>
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: 906619a009 ("wifi: ath12k: handle regulatory hints during mac registration")
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250626-fix_timeout_during_interface_creation-v1-1-90a7fdc222d4@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
When setting a new bitrate, WMI peer association command is sent from
the host without the peer authentication bit set in peer_flags for
security mode, which causes ping failure.
The firmware handles peer_flags when the client is associating, as the
peer authentication bit in peer_flags is set after the key exchange.
When the WMI peer association command is sent from the host to update
the new bitrate for an associated STA, the firmware expects the WMI
peer authentication bit to be set in peer_flags.
Fix this issue by ensuring that the WMI peer auth bit is set in
peer_flags in WMI peer association command when updating the new
bitrate.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: Thiraviyam Mariyappan <thiraviyam.mariyappan@oss.qualcomm.com>
Signed-off-by: Ramasamy Kaliappan <ramasamy.kaliappan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250608145651.1735236-1-ramasamy.kaliappan@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Add the missing memory barriers to make sure that destination ring
descriptors are read before updating the tail pointer (and passing
ownership to the device) to avoid memory corruption on weakly ordered
architectures like aarch64 when the ring is full.
Tested-on: WCN7850 hw2.0 WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Cc: stable@vger.kernel.org # 6.3
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250617084402.14475-5-johan+linaro@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Add the missing memory barrier to make sure that LMAC source ring
descriptors are written before updating the head pointer to avoid
passing stale data to the firmware on weakly ordered architectures like
aarch64.
Note that non-LMAC rings use MMIO write accessors which have the
required write memory barrier.
Tested-on: WCN7850 hw2.0 WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Cc: stable@vger.kernel.org # 6.3
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250617084402.14475-4-johan+linaro@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The read memory barrier added by commit 6b67d2cf14 ("wifi: ath12k: fix
ring-buffer corruption") is enough to guarantee ordering also for plain
descriptor accesses if the length helper is ever inlined so drop the
unnecessary READ_ONCE().
Tested-on: WCN7850 hw2.0 WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250617084402.14475-3-johan+linaro@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Add the missing memory barrier to make sure that destination ring
descriptors are read after the head pointers to avoid using stale data
on weakly ordered architectures like aarch64.
The barrier is added to the ath12k_hal_srng_access_begin() helper for
symmetry with follow-on fixes for source ring buffer corruption which
will add barriers to ath12k_hal_srng_access_end().
Tested-on: WCN7850 hw2.0 WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Cc: stable@vger.kernel.org # 6.3
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250617084402.14475-2-johan+linaro@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Add the missing memory barriers to make sure that destination ring
descriptors are read before updating the tail pointer (and passing
ownership to the device) to avoid memory corruption on weakly ordered
architectures like aarch64 when the ring is full.
Tested-on: WCN6855 hw2.1 WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.41
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Cc: stable@vger.kernel.org # 5.6
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250604143457.26032-6-johan+linaro@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Add the missing memory barrier to make sure that LMAC source ring
descriptors are written before updating the head pointer to avoid
passing stale data to the firmware on weakly ordered architectures like
aarch64.
Note that non-LMAC rings use MMIO write accessors which have the
required write memory barrier.
Tested-on: WCN6855 hw2.1 WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.41
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Cc: stable@vger.kernel.org # 5.6
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250604143457.26032-5-johan+linaro@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The read memory barrier added by commit ab52e3e44f ("wifi: ath11k: fix
rx completion meta data corruption") is enough to guarantee ordering
also for plain descriptor accesses so drop the unnecessary READ_ONCE().
Tested-on: WCN6855 hw2.1 WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.41
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250604143457.26032-4-johan+linaro@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The read memory barrier added by commit 6d037a372f ("wifi: ath11k: fix
ring-buffer corruption") is enough to guarantee ordering also for plain
descriptor accesses if the length helper is ever inlined so drop the
unnecessary READ_ONCE().
Tested-on: WCN6855 hw2.1 WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.41
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250604143457.26032-3-johan+linaro@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Add the missing memory barrier to make sure that destination ring
descriptors are read after the head pointers to avoid using stale data
on weakly ordered architectures like aarch64.
The barrier is added to the ath11k_hal_srng_access_begin() helper for
symmetry with follow-on fixes for source ring buffer corruption which
will add barriers to ath11k_hal_srng_access_end().
Tested-on: WCN6855 hw2.1 WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.41
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Cc: stable@vger.kernel.org # 5.6
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250604143457.26032-2-johan+linaro@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The power value is 6 dBm on an AP operating on the 6 GHz channel.
This is a very low value.
On 6 GHz, the target computes the EIRP based on the power values sent
in the WMI_VDEV_SET_TPC_POWER_CMD. Currently, this is being sent only
for station interfaces and not for AP interfaces.
Therefore, add AP vdev to the condition in
ath12k_mac_station_supports_tpc() and rename
ath12k_mac_station_supports_tpc() to ath12k_mac_supports_tpc().
For a AP vdev, hardcode ap_power_type as IEEE80211_REG_LPI_AP, which is
filled in the WMI_VDEV_SET_TPC_POWER_CMDID sent to the target.
Currently, LPI is the only supported AP power mode. Since there is
no method currently to set the AP power mode from user-space, the
power mode is hard-coded to LPI.
Retain the existing logic for populating the power mode for a station
vdev.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Hariharan Basuthkar <quic_hbasuthk@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250606112316.39316-1-quic_hbasuthk@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
When both AP/STA and monitor interfaces are enabled, ieee80211_tx_status()
is invoked from two paths: the TX completion handler for data frames
and the WMI TX completion handler for management frames.
In the data path, the skb->cb is properly zeroed using memset, but in
the WMI path, this step is missing.
As a result, mac80211 encountered uninitialized (junk) values in
skb->cb when generating the radiotap header for monitor mode, leading
to invalid radiotap lengths.
Hence, explicitly zero the status field in the skb->cb using memset
in WMI TX completion path to ensure consistent and correct behavior
during WMI tx completion path.
Additionally, set info->status.rates[0].idx = -1 to indicate that
no valid rate information is available, avoiding misinterpretation of
garbage values.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sarika Sharma <quic_sarishar@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250603063512.1887652-1-quic_sarishar@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, when a station is associated with a Non-Transmitting BSS of an
MBSSID set, beacons are not frequently received from the firmware. This
results in missing events via beacons, such as channel switches, leading
to the station not switching to new channel as the AP does, eventually
causing a kick out event from the firmware. This issue arises due to
missing configuration of Non-Transmitting BSS information in station's
vdev up command.
Fix this by filling information such as the Transmitting BSSID, profile index
and profile count in vdev up command of station.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Signed-off-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250530035615.3178480-3-rameshkumar.sundaram@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
ath12k station is unable to associate with non-transmitting BSSes
in a Multiple BSS set because the user-space does not receive
information about the non-transmitting BSSes from mac80211's
scan results.
The ath12k driver does not advertise its MBSSID capability to mac80211,
resulting in wiphy->support_mbssid not being set. Consequently, the
information about non-transmitting BSS is not parsed from received
Beacon/Probe response frames and is therefore not included in the
scan results.
Fix this by advertising the MBSSID capability of ath12k driver to
mac80211.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Signed-off-by: Hari Chandrakanthan <quic_haric@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250530035615.3178480-2-rameshkumar.sundaram@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
ATH12K_DEFAULT_NOISE_FLOOR represents the approximate noise floor value
which is used for RSSI calculation. Commit "wifi: ath12k: handle WMI event
for real noise floor calculation" added support to get the real noise floor
value from the firmware. Add changes to use the real value now instead of
the default one.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Co-developed-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250623-support_real_noise_floor-v2-2-974bbafa317e@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
At present, the ATH12K_DEFAULT_NOISE_FLOOR (-95) is used to calculate RSSI
value, providing an estimated noise floor value. Consequently, the RSSI
value is also approximate. This works but however, using actual noise floor
value will enable the reporting of the true RSSI value.
The firmware possesses the necessary data to determine the actual noise
floor. This data is provided to the host via the WMI event
WMI_PDEV_RSSI_DBM_CONVERSION_PARAMS_INFO_EVENTID, which includes the
runtime parameters needed for calculating the real noise floor in dBm. This
event is triggered by the firmware during channel changes, temperature
offset adjustments, and hardware chainmask modifications. The individual
TLVs may not always be present in each event. For instance, temperature
information might only appear if there is a change in offset due to
temperature variation.
Add support to handle and parse this WMI event. Use the received values to
calculate and store the noise floor value.
A subsequent change will use this noise floor value in the actual RSSI
calculation.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Co-developed-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250623-support_real_noise_floor-v2-1-974bbafa317e@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Don't populate the read-only array svc_id on the stack at run time,
instead make it static const.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250619082010.1834109-1-colin.i.king@gmail.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Make sure to deregister the PM notifier to avoid a use-after-free on
suspend in case core initialisation fails (e.g. due to missing
firmware).
Tested-on: WCN6855 hw2.0 WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.41
Fixes: 32d93b51bc ("wifi: ath11k: choose default PM policy for hibernation")
Reported-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Closes: https://lore.kernel.org/all/d0cd065c-1cd1-4e56-8c57-60777b1f3664@oss.qualcomm.com/
Cc: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://patch.msgid.link/20250624082022.15469-1-johan+linaro@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In a number of cases we see kernel panics on resume due
to ath11k kernel page fault, which happens under the
following circumstances:
1) First ath11k_hal_dump_srng_stats() call
Last interrupt received for each group:
ath11k_pci 0000:01:00.0: group_id 0 22511ms before
ath11k_pci 0000:01:00.0: group_id 1 14440788ms before
[..]
ath11k_pci 0000:01:00.0: failed to receive control response completion, polling..
ath11k_pci 0000:01:00.0: Service connect timeout
ath11k_pci 0000:01:00.0: failed to connect to HTT: -110
ath11k_pci 0000:01:00.0: failed to start core: -110
ath11k_pci 0000:01:00.0: firmware crashed: MHI_CB_EE_RDDM
ath11k_pci 0000:01:00.0: already resetting count 2
ath11k_pci 0000:01:00.0: failed to wait wlan mode request (mode 4): -110
ath11k_pci 0000:01:00.0: qmi failed to send wlan mode off: -110
ath11k_pci 0000:01:00.0: failed to reconfigure driver on crash recovery
[..]
2) At this point reconfiguration fails (we have 2 resets) and
ath11k_core_reconfigure_on_crash() calls ath11k_hal_srng_deinit()
which destroys srng lists. However, it does not reset per-list
->initialized flag.
3) Second ath11k_hal_dump_srng_stats() call sees stale ->initialized
flag and attempts to dump srng stats:
Last interrupt received for each group:
ath11k_pci 0000:01:00.0: group_id 0 66785ms before
ath11k_pci 0000:01:00.0: group_id 1 14485062ms before
ath11k_pci 0000:01:00.0: group_id 2 14485062ms before
ath11k_pci 0000:01:00.0: group_id 3 14485062ms before
ath11k_pci 0000:01:00.0: group_id 4 14780845ms before
ath11k_pci 0000:01:00.0: group_id 5 14780845ms before
ath11k_pci 0000:01:00.0: group_id 6 14485062ms before
ath11k_pci 0000:01:00.0: group_id 7 66814ms before
ath11k_pci 0000:01:00.0: group_id 8 68997ms before
ath11k_pci 0000:01:00.0: group_id 9 67588ms before
ath11k_pci 0000:01:00.0: group_id 10 69511ms before
BUG: unable to handle page fault for address: ffffa007404eb010
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 100000067 P4D 100000067 PUD 10022d067 PMD 100b01067 PTE 0
Oops: 0000 [#1] PREEMPT SMP NOPTI
RIP: 0010:ath11k_hal_dump_srng_stats+0x2b4/0x3b0 [ath11k]
Call Trace:
<TASK>
? __die_body+0xae/0xb0
? page_fault_oops+0x381/0x3e0
? exc_page_fault+0x69/0xa0
? asm_exc_page_fault+0x22/0x30
? ath11k_hal_dump_srng_stats+0x2b4/0x3b0 [ath11k (HASH:6cea 4)]
ath11k_qmi_driver_event_work+0xbd/0x1050 [ath11k (HASH:6cea 4)]
worker_thread+0x389/0x930
kthread+0x149/0x170
Clear per-list ->initialized flag in ath11k_hal_srng_deinit().
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Fixes: 5118935b1b ("ath11k: dump SRNG stats during FW assert")
Link: https://patch.msgid.link/20250612084551.702803-1-senozhatsky@chromium.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Introduce 'firmware-name' property to allow end-users and/or integrators to
decide which usecase-specific firmware to run on the WCN6855. This is
necessary due to resource limitations such as memory capacity and CPU
capability, or performance and power optimization for different application
scenarios.
Currently, there are two firmwares, both files can be executed
interchangeably.
For example:
- ath11k/WCN6855/hw2.0/amss.bin,
ath11k/WCN6855/hw2.0/m3.bin
ath11k/WCN6855/hw2.0/board-2.bin
- ath11k/WCN6855/hw2.0/nfa765/amss.bin,
ath11k/WCN6855/hw2.0/nfa765/m3.bin
ath11k/WCN6855/hw2.0/board-2.bin
The former is the default firmware, suitable for most WiFi 6 STA functions.
The latter adds support for commercial-quality SAP and optimizes power
consumption for IoT applications. And both use the same BDF/regdb data
within the main board-2.bin.
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-04479-QCAHSPSWPL_V1_V2_SILICONZ_IOE-1
Signed-off-by: Miaoqing Pan <miaoqing.pan@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250522013444.1301330-3-miaoqing.pan@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Since 2b0996c764 , all of this platform code became no-op with no OF
replacement. Not only that, there are no users of AHB here. Add an OF
match table that mostly mirrors the original platform device id table.
Use a qca prefix as is done for the only other property: qca,no-eeprom.
Also used qca prefix for ar9530 as the latter seems to be a mistake.
This will be used to add ath9k support for the various ath79 devices
here.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://patch.msgid.link/20250609030851.17739-5-rosenp@gmail.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Alphabetic includes are easier to look at and to make further changes to
them.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://patch.msgid.link/20250609030851.17739-3-rosenp@gmail.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Easier to look at. Follows netdev style.
Also remove ret assignment. Because of all of these devm conversions,
ret = 0 is a path that never gets hit. The first time it does it when
request_irq fails, but that ends up reassigning it.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://patch.msgid.link/20250609030851.17739-2-rosenp@gmail.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
All ath drivers:
Add "#include <linux/export.h>" to all files that use EXPORT_SYMBOL()
to fix a newly introduced 'make W=1' check. Note that check has
subsequently been changed to only test when W=2, but keep the fixes to
suppress the warning for 'make W=2'.
ath12k:
Properly handle scan requests on multi-radio wiphy devices.
Perform the usual set of bug fixes and cleanups.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQ/mtSHzPUi16IfDEksFbugiYzLewUCaFq4qwAKCRAsFbugiYzL
e9nKAQC0wQ9QR53BFLGVu3TpR2hbaVaJmYlxCtf+DbrEUbOe1gEAgp2Cz0NdjUaQ
IABFyUquZS/ZAkqytpjXMvoilyDawAg=
=bBFE
-----END PGP SIGNATURE-----
Merge tag 'ath-next-20250624' of git://git.kernel.org/pub/scm/linux/kernel/git/ath/ath
Jeff Johnson says:
==================
ath.git patches for v6.17
All ath drivers:
Add "#include <linux/export.h>" to all files that use EXPORT_SYMBOL()
to fix a newly introduced 'make W=1' check. Note that check has
subsequently been changed to only test when W=2, but keep the fixes to
suppress the warning for 'make W=2'.
ath12k:
Properly handle scan requests on multi-radio wiphy devices.
Perform the usual set of bug fixes and cleanups.
==================
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, per-radio attributes are set on per-phy basis, i.e., all the
radios present in a wiphy will take attributes values sent from user. But
each radio in a wiphy can get different values from userspace based on
its requirement.
To extend support to set per-radio attributes, add support to get radio
index from userspace. Add an NL attribute - NL80211_ATTR_WIPHY_RADIO_INDEX,
to get user specified radio index for which attributes should be changed.
Pass this to individual drivers, so that the drivers can use this radio
index to change per-radio attributes when necessary. Currently, per-radio
attributes identified are:
NL80211_ATTR_WIPHY_TX_POWER_LEVEL
NL80211_ATTR_WIPHY_ANTENNA_TX
NL80211_ATTR_WIPHY_ANTENNA_RX
NL80211_ATTR_WIPHY_RETRY_SHORT
NL80211_ATTR_WIPHY_RETRY_LONG
NL80211_ATTR_WIPHY_FRAG_THRESHOLD
NL80211_ATTR_WIPHY_RTS_THRESHOLD
NL80211_ATTR_WIPHY_COVERAGE_CLASS
NL80211_ATTR_TXQ_LIMIT
NL80211_ATTR_TXQ_MEMORY_LIMIT
NL80211_ATTR_TXQ_QUANTUM
By default, the radio index is set to -1. This means the attribute should
be treated as a global configuration. If the user has not specified any
index, then the radio index passed to individual drivers would be -1. This
would indicate that the attribute applies to all radios in that wiphy.
Signed-off-by: Roopni Devanathan <quic_rdevanat@quicinc.com>
Link: https://patch.msgid.link/20250615082312.619639-2-quic_rdevanat@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In ath12k_dp_tx_get_encap_type(), the arvif parameter is only used to
retrieve the ab pointer. In vdev delete sequence the arvif->ar could
become NULL and that would trigger kernel panic.
Since the caller ath12k_dp_tx() already has a valid ab pointer, pass it
directly to avoid panic and unnecessary dereferencing.
PC points to "ath12k_dp_tx+0x228/0x988 [ath12k]"
LR points to "ath12k_dp_tx+0xc8/0x988 [ath12k]".
The Backtrace obtained is as follows:
ath12k_dp_tx+0x228/0x988 [ath12k]
ath12k_mac_tx_check_max_limit+0x608/0x920 [ath12k]
ieee80211_process_measurement_req+0x320/0x348 [mac80211]
ieee80211_tx_dequeue+0x9ac/0x1518 [mac80211]
ieee80211_tx_dequeue+0xb14/0x1518 [mac80211]
ieee80211_tx_prepare_skb+0x224/0x254 [mac80211]
ieee80211_xmit+0xec/0x100 [mac80211]
__ieee80211_subif_start_xmit+0xc50/0xf40 [mac80211]
ieee80211_subif_start_xmit+0x2e8/0x308 [mac80211]
netdev_start_xmit+0x150/0x18c
dev_hard_start_xmit+0x74/0xc0
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Fixes: e93bbd6554 ("wifi: ath12k: fix packets are sent in native wifi mode while we set raw mode")
Signed-off-by: Tamizh Chelvam Raja <tamizh.raja@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250606044936.3989400-1-tamizh.raja@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, the budget for monitor ring is reduced during each ring entry
reaping and again when the end reason is HAL_MON_END_OF_PPDU, leading to
inefficient budget use. The below mentioned commit intended to decrement
the budget only for HAL_MON_END_OF_PPDU but did not remove the other
decrement. Fix this by eliminating the budget decrement for each ring entry
reaping, ensuring the driver always reaps one full PPDU worth of entries
from the monitor destination ring.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: 394a3fa7c5 ("wifi: ath12k: Optimize NAPI budget by adjusting PPDU processing")
Signed-off-by: P Praneesh <praneesh.p@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250603103542.1164713-1-praneesh.p@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The commit 89ac53e962 ("wifi: ath12k: Enable REO queue lookup table
feature on QCN9274") originally intended to enable the reoq_lut_support
hardware parameter flag for both QCN9274 hw1.0 and hw2.0. However,
it enabled it only for QCN9274 hw1.0.
Hence, enable REO queue lookup table feature on QCN9274 hw2.0.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250609-qcn9274-reoq-v1-1-a92c91abc9b9@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Commit a934a57a42 ("scripts/misc-check: check missing #include
<linux/export.h> when W=1") introduced a new check that is producing
the following warning:
drivers/net/wireless/ath/ath12k/core.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
Add the missing #include to satisfy the check.
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250611-ath-unused-export-v1-5-c36819df7e7b@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Commit a934a57a42 ("scripts/misc-check: check missing #include
<linux/export.h> when W=1") introduced a new check that is producing
the following warnings:
drivers/net/wireless/ath/ath11k/ce.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath11k/core.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath11k/coredump.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath11k/debug.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath11k/debugfs.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath11k/dp.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath11k/fw.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath11k/hal.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath11k/pcic.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath11k/qmi.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath11k/trace.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
Add the missing #include to satisfy the check.
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250611-ath-unused-export-v1-4-c36819df7e7b@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Commit a934a57a42 ("scripts/misc-check: check missing #include
<linux/export.h> when W=1") introduced a new check that is producing
the following warnings:
drivers/net/wireless/ath/ath10k/bmi.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath10k/ce.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath10k/core.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath10k/coredump.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath10k/debug.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath10k/htc.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath10k/htt_rx.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath10k/htt_tx.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath10k/mac.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath10k/trace.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
Add the missing #include to satisfy the check.
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250611-ath-unused-export-v1-3-c36819df7e7b@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Commit a934a57a42 ("scripts/misc-check: check missing #include
<linux/export.h> when W=1") introduced a new check that is producing
the following warnings:
drivers/net/wireless/ath/ath9k/common-beacon.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath9k/common-debug.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath9k/common-init.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath9k/common-spectral.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath9k/common.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath9k/dynack.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
drivers/net/wireless/ath/ath9k/hw.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
Add the missing #include to satisfy the check.
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://patch.msgid.link/20250611-ath-unused-export-v1-2-c36819df7e7b@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Commit a934a57a42 ("scripts/misc-check: check missing #include
<linux/export.h> when W=1") introduced a new check that is producing
the following warning:
drivers/net/wireless/ath/main.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
Add the missing #include to satisfy the check.
Link: https://patch.msgid.link/20250611-ath-unused-export-v1-1-c36819df7e7b@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, TID is not decremented before peer cleanup, during error
handling path of ath12k_dp_rx_peer_frag_setup(). This could lead to
out-of-bounds access in peer->rx_tid[].
Hence, add a decrement operation for TID, before peer cleanup to
ensures proper cleanup and prevents out-of-bounds access issues when
the RX peer frag setup fails.
Found during code review. Compile tested only.
Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Sarika Sharma <quic_sarishar@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250526034713.712592-1-quic_sarishar@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
ath12k_dp_rx_deliver_msdu() currently includes logic related to
monitor mode handling. This code was inherited from the ath11k driver,
where a single rx handler was used for both regular and monitor mode
packets. In ath12k, however, monitor mode packets are handled separately
via ath12k_dp_mon_rx_deliver_msdu(), which contains all the necessary
monitor-specific logic. Therefore, monitor-related checks and operations
in ath12k_dp_rx_deliver_msdu() are no longer needed. Remove this dead code
to simplify the rx path and avoid unnecessary per-packet checks.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: P Praneesh <praneesh.p@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250605054438.1855365-1-praneesh.p@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
As station, WCN7850 firmware requires pairwise key to be installed before
group key. Currently host does not care about this, so it is up to kernel
or userspace to decide which one will be installed first. In case above
requirement is not met, WCN7850 firmware's EAPOL station machine is messed
up, and finally connection fails [1].
Reorder key install for station interface in that case: this is done by
caching group key first; Later when pairwise key arrives, both can be
installed in required order.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00217-QCAHKSWPL_SILICONZ-1
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218733
Link: https://lore.kernel.org/all/AS8P190MB12051DDBD84CD88E71C40AD7873F2@AS8P190MB1205.EURP190.PROD.OUTLOOK.COM # [1]
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250523-ath12k-unicast-key-first-v1-2-f53c3880e6d8@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
WMI_KEY_PAIRWISE and WMI_KEY_GROUP are not bit fields, change
bit operation to direct assignment to avoid confusion.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00217-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250523-ath12k-unicast-key-first-v1-1-f53c3880e6d8@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
If a regulatory notification is there in the system while the hardware is
being registered, it attempts to set the new regulatory country. However,
ath12k currently boots with a default country derived from the BDF. If this
default country differs from the one provided in the notification, a race
condition can occur while updating the regulatory information back to
userspace. This potentially leads to driver having the incorrect regulatory
applied.
For example, suppose the regulatory domain for France (FR) is already
applied, and then the driver is loaded with a BDF that has the United
States (US) country programmed. When the driver finishes loading, the
regulatory domain shown in phyX still reflects the US regulatory settings.
This is incorrect, as the driver had already received a notification for
FR during hardware registration, but failed to process it properly due to
the race condition.
The race condition exists during driver initialization and hardware
registration:
- On driver load, the firmware sends BDF-based country regulatory rules,
which are stored in default_regd via ath12k_reg_handle_chan_list().
- During hardware registration, a regulatory notification is triggered
through:
ath12k_mac_hw_register()
-> ieee80211_register_hw()
-> wiphy_register()
-> wiphy_regulatory_register()
-> reg_call_notifier()
This sends a country code to the firmware, which responds with updated
regulatory rules.
- After registration, ath12k_mac_hw_register() calls ath12k_regd_update(),
which copies default_regd and passes it to the upper layers.
The race occurs between the firmware's response and the execution of
ath12k_regd_update(). If the firmware's new rules are processed before the
update call, the correct values are used. Otherwise, outdated boot-time
country settings are exposed to userspace.
To resolve this issue, introduce a completion mechanism within the hardware
group (ah). Trigger this completion whenever a regulatory change is
requested from the firmware. Then, in ath12k_regd_update(), wait for the
firmware to complete its regulatory processing before proceeding with the
update.
This ensures that during driver load, the default country is processed
first. However, before ath12k_regd_update() is called, the new regulatory
notification will have already been received by the driver. As a result, it
will wait for the firmware's regulatory processing to complete, and only
the final, correct regulatory domain will be updated to userspace.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250617-handle_user_regd_update_hints_during_insmod-v2-1-10a6a48efe81@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
With previous patch [1], ath12k_reg_update_chan_list() will be called
during reg_process_self_managed_hint().
reg_process_self_managed_hint() will hold rtnl_lock all the time.
But ath12k_reg_update_chan_list() may increase the occupation time of
rtnl_lock, because when wait flag is set, wait_for_completion_timeout()
will be called during 11d/hw scan.
Should minimize the occupation time of rtnl_lock as much as possible
to avoid interfering with rest of the system. So move the update channel
list operation to a new worker, so that wait_for_completion_timeout()
won't be called with the rtnl_lock held.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: f335295aa2 ("wifi: ath12k: avoid deadlock during regulatory update in ath12k_regd_update()") #[1]
Signed-off-by: Kang Yang <kang.yang@oss.qualcomm.com>
Reviewed-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250605082528.701-1-kang.yang@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
When two split-phy devices that support overlapping frequency ranges within
the same band are grouped into an ath12k hardware (HW) setup, they share a
common wiphy instance. Consequently, the channel list (wiphy->bands[])
becomes unified across all associated radios (ar).
For reference, the devices are:
2.4 GHz + 5 GHz Low Band
5 GHz High Band + 6 GHz
The first radio probed within the 5 GHz range (say 5 GHz Low Band) updates
its sband reference (&ar->mac.sbands[NL80211_BAND_5GHZ]) within
wiphy->bands[]. However, when the second 5 GHz radio (5 GHz High Band) is
probed, it replaces the existing wiphy->bands[] entry with its own sub-band
reference. As a result, wiphy->bands[] always reflects the channel list
from the most recently probed radio in that band, restricting supported
channels to those within its specific range for upper-layer.
Fix this by updating the wiphy->bands[] to just enable the channels of
current radio when there exist a radio which already has set it.
This will make sure wiphy->bands[] holds reference of first radio which
got probed in 5 GHz band and subsequent radio just updates the channel list
in the same address space.
Since same sband memory space is shared between radios of a band, while
determining the allowed frequency range of radio, its frequency limits
(ar->freq_range.start_freq, end_freq) should be used.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Signed-off-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250522111514.3735107-1-rameshkumar.sundaram@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
When two split-phy devices having supported frequency range in same band
(as mentioned below) are combined into an ath12k HW group, they will be
part of same wiphy and hence the channel list (wiphy->bands[]) will be
common for all of the radios (ar).
1 - 2.4 GHz + 5 GHz Low band
2 - 5 GHz High band + 6 GHz
When a scan is triggered with frequency list containing frequencies of
both 5 GHz low and 5 GHz high, mac80211 generates a single scan request
to driver with both the frequencies. This is because mac80211 splits the
scan request based on band.
ath12k checks the first frequency in the requested scan frequency list and
initiates scan to corresponding radio's(ar) firmware with all the
frequencies. Firmware rejects this scan as some frequencies in the scan
request are not supported, resulting is scan failure.
Fix this by splitting the scan request into multiples scans in driver
based on the supported frequency range of different radios in a band and
schedule scans in parallel to them.
Finally send scan completion/abort notification to mac80211 after all the
radios complete their scheduled scan.
Also, last_scan_link is not needed anymore as ath12k internally schedules
multiple scans, remove the same and use ahvif->links_map to identify
scan links when scan is cancelled.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Co-developed-by: Vignesh C <quic_vignc@quicinc.com>
Signed-off-by: Vignesh C <quic_vignc@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Mahendran P <quic_mahep@quicinc.com>
Link: https://patch.msgid.link/20250507194832.2501668-3-rameshkumar.sundaram@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
When two split-phy devices that support overlapping frequency ranges within
the same band(say 5 GHz low and 5 GHz high) are grouped into an ath12k
hardware (HW) setup, they share a common wiphy instance. Consequently, the
channel list (wiphy->bands[]) becomes unified across all associated
radios (ar).
When a scan is triggered with frequency list containing frequencies of
both 5 GHz low and 5 GHz high, mac80211 generates a single scan request
to driver with all the frequencies. This is because mac80211 splits the
scan request based on band.
ath12k checks the first frequency in the requested scan frequency list and
initiates scan to corresponding radio's(ar) firmware with all the
frequencies. Firmware rejects this scan since some of the frequencies in
the scan request are not supported, resulting in a scan failure.
To fix this ath12k driver should split the scan request into multiple
scans based on requested frequencies and schedule them to corresponding
underlying radio(s) in parallel.
Currently, ath12k driver assigns the scan link (link 15) in ahvif->links[]
for scan vdev creation. However, with parallel scan support being
introduced in the following patch, multiple radios (e.g., 5 GHz low and
5 GHz high) in the same HW group may attempt to use the same scan link
concurrently, causing conflicts where the vdev created by one radio could
be deleted and re-initialized by another.
To address this, reserve space for additional scan links for each radio in
a MLO group and allow subsequent radios to use different available scan
links (ahvif->link[15..MAX_SCAN_LINKS]) when scan link (15) is
pre-occupied.
While at it, rename ATH12K_DEFAULT_SCAN_LINK as ATH12K_FIRST_SCAN_LINK
as there is no longer only one scan link.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Mahendran P <quic_mahep@quicinc.com>
Link: https://patch.msgid.link/20250507194832.2501668-2-rameshkumar.sundaram@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In MLO configuration, ath12k_mac_radio_start() iterates through all
the radios and makes the ar state 'ON'. Even though some bands are
not supported in certain countries, ath12k_reg_update_chan_list()
tries to update the channel list for all the active pdevs and ends
up in the warn_on for non-supported band.
To prevent this, disable the pdev when the number of channels across
all bands supported by the pdev is zero for a particular country.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthik M <quic_karm@quicinc.com>
Signed-off-by: Muna Sinada <muna.sinada@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250506214930.3561348-1-muna.sinada@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
During beacon miss handling, ath12k driver iterates over active virtual
interfaces (vifs) and attempts to access the radio object (ar) via
arvif->deflink->ar.
However, after commit aa80f12f3b ("wifi: ath12k: defer vdev creation for
MLO"), arvif is linked to a radio only after vdev creation, typically when
a channel is assigned or a scan is requested.
For P2P capable devices, a default P2P interface is created by
wpa_supplicant along with regular station interfaces, these serve as dummy
interfaces for P2P-capable stations, lack an associated netdev and initiate
frequent scans to discover neighbor p2p devices. When a scan is initiated
on such P2P vifs, driver selects destination radio (ar) based on scan
frequency, creates a scan vdev, and attaches arvif to the radio. Once the
scan completes or is aborted, the scan vdev is deleted, detaching arvif
from the radio and leaving arvif->ar uninitialized.
While handling beacon miss for station interfaces, P2P interface is also
encountered in the vif iteration and ath12k_mac_handle_beacon_miss_iter()
tries to dereference the uninitialized arvif->deflink->ar.
Fix this by verifying that vdev is created for the arvif before accessing
its ar during beacon miss handling and similar vif iterator callbacks.
==========================================================================
wlp6s0: detected beacon loss from AP (missed 7 beacons) - probing
KASAN: null-ptr-deref in range [0x0000000000000010-0x0000000000000017]
CPU: 5 UID: 0 PID: 0 Comm: swapper/5 Not tainted 6.16.0-rc1-wt-ath+ #2 PREEMPT(full)
RIP: 0010:ath12k_mac_handle_beacon_miss_iter+0xb5/0x1a0 [ath12k]
Call Trace:
__iterate_interfaces+0x11a/0x410 [mac80211]
ieee80211_iterate_active_interfaces_atomic+0x61/0x140 [mac80211]
ath12k_mac_handle_beacon_miss+0xa1/0xf0 [ath12k]
ath12k_roam_event+0x393/0x560 [ath12k]
ath12k_wmi_op_rx+0x1486/0x28c0 [ath12k]
ath12k_htc_process_trailer.isra.0+0x2fb/0x620 [ath12k]
ath12k_htc_rx_completion_handler+0x448/0x830 [ath12k]
ath12k_ce_recv_process_cb+0x549/0x9e0 [ath12k]
ath12k_ce_per_engine_service+0xbe/0xf0 [ath12k]
ath12k_pci_ce_workqueue+0x69/0x120 [ath12k]
process_one_work+0xe3a/0x1430
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284.1-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: aa80f12f3b ("wifi: ath12k: defer vdev creation for MLO")
Signed-off-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250618185635.750470-1-rameshkumar.sundaram@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Fix the following 3 issues:
wifi: ath12k: avoid burning CPU while waiting for firmware stats
wifi: ath12k: don't activate more links than firmware supports
wifi: carl9170: do not ping device which has failed to load firmware
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQ/mtSHzPUi16IfDEksFbugiYzLewUCaFIHEQAKCRAsFbugiYzL
e0sRAP41jxddaDsw+Kc3JxH5D9HytK0A0x3hqfDx+IYViWjcwQD6AsdAOY7eEimL
slL7/uBiIUaytaagNc3YGb2+IffjBQM=
=b7cq
-----END PGP SIGNATURE-----
Merge tag 'ath-current-20250617' of git://git.kernel.org/pub/scm/linux/kernel/git/ath/ath
Jeff Johnson says:
==================
ath.git updates for v6.16-rc3
Fix the following 3 issues:
wifi: ath12k: avoid burning CPU while waiting for firmware stats
wifi: ath12k: don't activate more links than firmware supports
wifi: carl9170: do not ping device which has failed to load firmware
==================
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For WMI_REQUEST_VDEV_STAT request, firmware might split response into
multiple events dut to buffer limit, hence currently in
ath12k_wmi_fw_stats_process() host waits until all events received. In
case there is no vdev started, this results in that below condition
would never get satisfied
((++ar->fw_stats.num_vdev_recvd) == total_vdevs_started)
consequently the requestor would be blocked until time out.
The same applies to WMI_REQUEST_BCN_STAT request as well due to:
((++ar->fw_stats.num_bcn_recvd) == ar->num_started_vdevs)
Change to check the number of started vdev first: if it is zero, finish
directly; if not, follow the old way.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284.1-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 WLAN.WBE.1.5-01651-QCAHKSWPL_SILICONZ-1
Fixes: e367c92476 ("wifi: ath12k: Request vdev stats from firmware")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250612-ath12k-fw-fixes-v1-4-12f594f3b857@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently ath12k_wmi_fw_stats_process() is using static variables to count
firmware stat events. Taking num_vdev as an example, if for whatever
reason (say ar->num_started_vdevs is 0 or firmware bug etc.) the following
condition
(++num_vdev) == total_vdevs_started
is not met, is_end is not set thus num_vdev won't be cleared. Next time
when firmware stats is requested again, even if everything is working
fine, failure is expected due to the condition above will never be
satisfied.
The same applies to num_bcn as well.
Change to use non-static counters and reset them each time before firmware
stats is requested.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284.1-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 WLAN.WBE.1.5-01651-QCAHKSWPL_SILICONZ-1
Fixes: e367c92476 ("wifi: ath12k: Request vdev stats from firmware")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250612-ath12k-fw-fixes-v1-3-12f594f3b857@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
ath12k_mac_get_fw_stats() is busy polling fw_stats_done flag while waiting
firmware finishing sending all events. This is not good as CPU is
monopolized and kept burning during the wait.
Change to the completion mechanism to fix it.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284.1-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 WLAN.WBE.1.5-01651-QCAHKSWPL_SILICONZ-1
Fixes: e367c92476 ("wifi: ath12k: Request vdev stats from firmware")
Reported-by: Grégoire Stein <gregoire.s93@live.fr>
Closes: https://lore.kernel.org/ath12k/AS8P190MB120575BBB25FCE697CD7D4988763A@AS8P190MB1205.EURP190.PROD.OUTLOOK.COM/
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Tested-by: Grégoire Stein <gregoire.s93@live.fr>
Link: https://patch.msgid.link/20250612-ath12k-fw-fixes-v1-2-12f594f3b857@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Regarding the firmware stats events handling, the comment in
ath12k_mac_get_fw_stats() says host determines whether all events have been
received based on 'end' tag in TLV. This is wrong as there is no such tag
at all, actually host makes the decision totally by itself based on the
stats type and active pdev/vdev counts etc.
Fix it to correctly reflect the logic.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284.1-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 WLAN.WBE.1.5-01651-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250612-ath12k-fw-fixes-v1-1-12f594f3b857@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In case of ML connection, currently all useful links are activated at
ASSOC stage:
ieee80211_set_active_links(vif, ieee80211_vif_usable_links(vif))
this results in firmware crash when the number of links activated on the
same device is more than supported.
Since firmware supports activating at most 2 links for a ML connection,
to avoid firmware crash, host needs to select 2 links out of the useful
links. As the assoc link has already been chosen, the question becomes
how to determine partner links. A straightforward principle applied
here is that the resulted combination should achieve the best throughput.
For that purpose, ideally various factors like bandwidth, RSSI etc should
be considered. But that would be too complicate. To make it easy, the
choice is to only take hardware modes into consideration.
The SBS (single band simultaneously) mode frequency range covers 5 GHz
and 6 GHz bands. In this mode, the two individual MACs are both active,
with one working on 5g-high band and the other on 5g-low band (from
hardware perspective 5 GHz and 6 GHz bands are referred to as a 'large'
single 5 GHz band). The DBS (dual band simultaneously) mode covers 2 GHz
band and the 'large' 5 GHz band, with one MAC working on 2 GHz band and
the other working on 5 GHz band or 6 GHz band. Since 5,6 GHz bands could
provide higher bandwidth than 2 GHz band, the preference is given to SBS
mode. Other hardware modes results in only one working MAC at any given
time, so it is chosen only when both SBS are DBS are not possible.
For each hardware mode, if there are more than one partner candidate,
just choose the first one.
For now only single device MLO case is handled as it is easy. Other cases
could be addressed in the future.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250522-ath12k-sbs-dbs-v1-6-54a29e7a3a88@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In case of two links established on the same device in an ML connection,
depending on device's hardware mode capability, it is possible that both
links fall on the same MAC. Currently, no specific action is taken to
address this but just keep both links active. However this would result
in lower throughput compared to even one link, because switching between
these two links on the resulted MAC significantly impacts throughput.
Check if both links fall in the frequency range of a single MAC. If
so, send WMI_MLO_LINK_SET_ACTIVE_CMDID command to firmware such that
firmware can deactivate one of them. Note the decision of which link
getting deactivated is made by firmware, host only sends the vdev
lists.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250522-ath12k-sbs-dbs-v1-5-54a29e7a3a88@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Add WMI_MLO_LINK_SET_ACTIVE_CMDID command. This command allows host to
send required link information to firmware such that firmware can make
decision on activating/deactivating links in various scenarios.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250522-ath12k-sbs-dbs-v1-4-54a29e7a3a88@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Previous patches parse and save hardware MAC frequency range information
in ath12k_svc_ext_info structure. Such range represents hardware
capability hence needs to be updated based on host information, e.g. guard
the range based on host's low/high boundary.
So update frequency range. The updated range is saved in
ath12k_hw_mode_info structure and would be used when doing vdev activation
and link selection in following patches.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250522-ath12k-sbs-dbs-v1-3-54a29e7a3a88@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Firmware sends the boundary between lower and higher bands in
ath12k_wmi_dbs_or_sbs_cap_params structure embedded in
WMI_SERVICE_READY_EXT2_EVENTID event. The boundary is needed when
updating frequency range in the following patch. So parse and save
it for later use. Note ath12k_wmi_dbs_or_sbs_cap_params is placed
after some other structures, so placeholders for them are added
as well.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250522-ath12k-sbs-dbs-v1-2-54a29e7a3a88@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
WLAN hardware might support various hardware modes such as DBS (dual
band simultaneously), SBS (single band simultaneously) and DBS_OR_SBS
etc, see enum wmi_host_hw_mode_config_type. Firmware advertises actual
supported modes in WMI_SERVICE_READY_EXT_EVENTID event. For each mode,
firmware advertises frequency range each hardware MAC can operate on.
In MLO case such information is necessary during vdev activation and
link selection (which is done in following patches), so add a new
structure ath12k_svc_ext_info to ath12k_wmi_base, then parse and save
those information to it for later use.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250522-ath12k-sbs-dbs-v1-1-54a29e7a3a88@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
When the ath12k driver is built without CONFIG_ATH12K_DEBUG, the
recently refactored stats code can cause any user space application
(such at NetworkManager) to consume 100% CPU for 3 seconds, every time
stats are read.
Commit 'b8a0d83fe4c7 ("wifi: ath12k: move firmware stats out of
debugfs")' moved ath12k_debugfs_fw_stats_request() out of debugfs, by
merging the additional logic into ath12k_mac_get_fw_stats().
Among the added responsibility of ath12k_mac_get_fw_stats() was the
busy-wait for `fw_stats_done`.
Signalling of `fw_stats_done` happens when one of the
WMI_REQUEST_PDEV_STAT, WMI_REQUEST_VDEV_STAT, and WMI_REQUEST_BCN_STAT
messages are received, but the handling of the latter two commands remained
in the debugfs code. As `fw_stats_done` isn't signalled, the calling
processes will spin until the timeout (3 seconds) is reached.
Moving the handling of these two additional responses out of debugfs
resolves the issue.
Fixes: b8a0d83fe4 ("wifi: ath12k: move firmware stats out of debugfs")
Signed-off-by: Bjorn Andersson <bjorn.andersson@oss.qualcomm.com>
Tested-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://patch.msgid.link/20250609-ath12k-fw-stats-done-v1-1-2b3624656697@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Current release - regressions:
- af_unix: allow passing cred for embryo without SO_PASSCRED/SO_PASSPIDFD
Current release - new code bugs:
- eth: airoha: correct enable mask for RX queues 16-31
- veth: prevent NULL pointer dereference in veth_xdp_rcv when peer
disappears under traffic
- ipv6: move fib6_config_validate() to ip6_route_add(), prevent invalid
routes
Previous releases - regressions:
- phy: phy_caps: don't skip better duplex match on non-exact match
- dsa: b53: fix untagged traffic sent via cpu tagged with VID 0
- Revert "wifi: mwifiex: Fix HT40 bandwidth issue.", it caused transient
packet loss, exact reason not fully understood, yet
Previous releases - always broken:
- net: clear the dst when BPF is changing skb protocol (IPv4 <> IPv6)
- sched: sfq: fix a potential crash on gso_skb handling
- Bluetooth: intel: improve rx buffer posting to avoid causing issues
in the firmware
- eth: intel: i40e: make reset handling robust against multiple requests
- eth: mlx5: ensure FW pages are always allocated on the local NUMA
node, even when device is configure to 'serve' another node
- wifi: ath12k: fix GCC_GCC_PCIE_HOT_RST definition for WCN7850,
prevent kernel crashes
- wifi: ath11k: avoid burning CPU in ath11k_debugfs_fw_stats_request()
for 3 sec if fw_stats_done is not set
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=0mtm
-----END PGP SIGNATURE-----
Merge tag 'net-6.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from bluetooth and wireless.
Current release - regressions:
- af_unix: allow passing cred for embryo without SO_PASSCRED/SO_PASSPIDFD
Current release - new code bugs:
- eth: airoha: correct enable mask for RX queues 16-31
- veth: prevent NULL pointer dereference in veth_xdp_rcv when peer
disappears under traffic
- ipv6: move fib6_config_validate() to ip6_route_add(), prevent
invalid routes
Previous releases - regressions:
- phy: phy_caps: don't skip better duplex match on non-exact match
- dsa: b53: fix untagged traffic sent via cpu tagged with VID 0
- Revert "wifi: mwifiex: Fix HT40 bandwidth issue.", it caused
transient packet loss, exact reason not fully understood, yet
Previous releases - always broken:
- net: clear the dst when BPF is changing skb protocol (IPv4 <> IPv6)
- sched: sfq: fix a potential crash on gso_skb handling
- Bluetooth: intel: improve rx buffer posting to avoid causing issues
in the firmware
- eth: intel: i40e: make reset handling robust against multiple
requests
- eth: mlx5: ensure FW pages are always allocated on the local NUMA
node, even when device is configure to 'serve' another node
- wifi: ath12k: fix GCC_GCC_PCIE_HOT_RST definition for WCN7850,
prevent kernel crashes
- wifi: ath11k: avoid burning CPU in ath11k_debugfs_fw_stats_request()
for 3 sec if fw_stats_done is not set"
* tag 'net-6.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (70 commits)
selftests: drv-net: rss_ctx: Add test for ntuple rules targeting default RSS context
net: ethtool: Don't check if RSS context exists in case of context 0
af_unix: Allow passing cred for embryo without SO_PASSCRED/SO_PASSPIDFD.
ipv6: Move fib6_config_validate() to ip6_route_add().
net: drv: netdevsim: don't napi_complete() from netpoll
net/mlx5: HWS, Add error checking to hws_bwc_rule_complex_hash_node_get()
veth: prevent NULL pointer dereference in veth_xdp_rcv
net_sched: remove qdisc_tree_flush_backlog()
net_sched: ets: fix a race in ets_qdisc_change()
net_sched: tbf: fix a race in tbf_change()
net_sched: red: fix a race in __red_change()
net_sched: prio: fix a race in prio_tune()
net_sched: sch_sfq: reject invalid perturb period
net: phy: phy_caps: Don't skip better duplex macth on non-exact match
MAINTAINERS: Update Kuniyuki Iwashima's email address.
selftests: net: add test case for NAT46 looping back dst
net: clear the dst when changing skb protocol
net/mlx5e: Fix number of lanes to UNKNOWN when using data_rate_oper
net/mlx5e: Fix leak of Geneve TLV option object
net/mlx5: HWS, make sure the uplink is the last destination
...
Fix a handful of both build and stability issues across multiple drivers.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQ/mtSHzPUi16IfDEksFbugiYzLewUCaEXB6gAKCRAsFbugiYzL
e1C9AQDjoq8eMj4tlqv8bliSiF1GqgxKWtKmaujMTkNxOpgc0gD/RV4o274RPP5C
OjghnAWYRoRUjhRCKcLLoECa6xkzJQY=
=1nxf
-----END PGP SIGNATURE-----
Merge tag 'ath-current-20250608' of git://git.kernel.org/pub/scm/linux/kernel/git/ath/ath
Jeff Johnson says:
==================
ath.git updates for v6.16-rc2
Fix a handful of both build and stability issues across multiple drivers.
==================
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move this API to the canonical timer_*() namespace.
[ tglx: Redone against pre rc1 ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/aB2X0jCKQO56WdMt@gmail.com
When the execution of ath12k_core_hw_group_assign() or
ath12k_core_hw_group_create() fails, the registered notifier chain is not
unregistered properly. Its memory is freed after rmmod, which may trigger
to a use-after-free (UAF) issue if there is a subsequent access to this
notifier chain.
Fixes the issue by calling ath12k_core_panic_notifier_unregister() in
failure cases.
Call trace:
notifier_chain_register+0x4c/0x1f0 (P)
atomic_notifier_chain_register+0x38/0x68
ath12k_core_init+0x50/0x4e8 [ath12k]
ath12k_pci_probe+0x5f8/0xc28 [ath12k]
pci_device_probe+0xbc/0x1a8
really_probe+0xc8/0x3a0
__driver_probe_device+0x84/0x1b0
driver_probe_device+0x44/0x130
__driver_attach+0xcc/0x208
bus_for_each_dev+0x84/0x100
driver_attach+0x2c/0x40
bus_add_driver+0x130/0x260
driver_register+0x70/0x138
__pci_register_driver+0x68/0x80
ath12k_pci_init+0x30/0x68 [ath12k]
ath12k_init+0x28/0x78 [ath12k]
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: 6f245ea0ec ("wifi: ath12k: introduce device group abstraction")
Signed-off-by: Miaoqing Pan <miaoqing.pan@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250604055250.1228501-1-miaoqing.pan@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently a warning is reported when running:
% scripts/kernel-doc -Wall -Werror -none drivers/net/wireless/ath/ath12k/hal.h
Warning: drivers/net/wireless/ath/ath12k/hal.h:596 Enum value 'HAL_REO_CMD_RESOURCE_BLOCKED' not described in enum 'hal_reo_cmd_status'
Add the missing description of HAL_REO_CMD_RESOURCE_BLOCKED.
Link: https://patch.msgid.link/20250605-hal_reo_cmd_status-kdoc-v1-1-e59f4b814b88@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
GCC_GCC_PCIE_HOT_RST is wrongly defined for WCN7850, causing kernel crash
on some specific platforms.
Since this register is divergent for WCN7850 and QCN9274, move it to
register table to allow different definitions. Then correct the register
address for WCN7850 to fix this issue.
Note IPQ5332 is not affected as it is not PCIe based device.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Reported-by: Parth Pancholi <parth.pancholi@toradex.com>
Closes: https://lore.kernel.org/all/86899b2235a59c9134603beebe08f2bb0b244ea0.camel@gmail.com
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Tested-by: Parth Pancholi <parth.pancholi@toradex.com>
Link: https://patch.msgid.link/20250523-ath12k-wrong-global-reset-addr-v1-1-3b06eb556196@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
if ath11k_crypto_mode is invalid (not ATH11K_CRYPT_MODE_SW/ATH11K_CRYPT_MODE_HW),
ath11k_core_qmi_firmware_ready() will not undo some actions that was previously
started/configured. Do the validation as soon as possible in order to avoid
undoing actions in that case and also to fix the following smatch warning:
drivers/net/wireless/ath/ath11k/core.c:2166 ath11k_core_qmi_firmware_ready()
warn: missing unwind goto?
Signed-off-by: Rodrigo Gobbi <rodrigo.gobbi.7@gmail.com>
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Closes: https://lore.kernel.org/r/202304151955.oqAetVFd-lkp@intel.com/
Fixes: aa2092a9ba ("ath11k: add raw mode and software crypto support")
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250522200519.16858-1-rodrigo.gobbi.7@gmail.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently to get firmware stats, ath11k_mac_op_get_txpower() calls
ath11k_fw_stats_request() and ath11k_mac_op_sta_statistics() calls
ath11k_mac_get_fw_stats(). Those two helpers are basically doing
the same, except for:
1. ath11k_mac_get_fw_stats() verifies ar->state inside itself.
2. ath11k_mac_get_fw_stats() calls ath11k_mac_fw_stats_request()
which then calls ath11k_mac_fw_stats_reset() to free pdev/vdev
stats whereas only pdev stats are freed by ath11k_fw_stats_request().
3. ath11k_mac_get_fw_stats() waits for ar->fw_stats_complete and
ar->fw_stats_done, whereas ath11k_fw_stats_request() only waits for
ar->fw_stats_complete.
Change to call ath11k_mac_get_fw_stats() in ath11k_mac_op_get_txpower().
This is valid because:
1. ath11k_mac_op_get_txpower() also has the same request on ar->state.
2. it is harmless to call ath11k_fw_stats_vdevs_free() since
ar->fw_stats.vdevs should be empty and there should be no one
expecting it at that time.
3. ath11k_mac_op_get_txpower() only needs pdev stats. For pdev stats,
ar->fw_stats_done is set to true whenever ar->fw_stats_complete is
set to true in ath11k_update_stats_event(). So additional wait on
ar->fw_stats_done does not wast any time.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.37
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250220082448.31039-8-quic_bqiang@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently ath11k_mac_get_fw_stats() is acquiring/releasing ar->conf_mutex by itself.
In order to reuse this function in a context where that lock is already taken, move
lock handling to its callers, then the function itself only has to assert it.
There is only one caller now, i.e., ath11k_mac_op_sta_statistics(), so add lock handling
there.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.37
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250220082448.31039-7-quic_bqiang@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently RCU lock and ar->data_lock are acquired in a sequence of
rcu_read_lock()
spin_lock_bh(&ar->data_lock)
but released in a sequence of
rcu_read_unlock()
spin_unlock_bh(&ar->data_lock)
Although there are no apparent issues with this, reorder them to
achieve symmetry.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.37
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250220082448.31039-6-quic_bqiang@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Commit b488c76644 ("ath11k: report rssi of each chain to mac80211 for QCA6390/WCN6855")
and commit c3b39553fc ("ath11k: add signal report to mac80211 for QCA6390 and WCN6855")
call debugfs functions in mac ops. Those functions are no-ops if CONFIG_ATH11K_DEBUGFS is
not enabled, thus cause wrong status reported.
Move them to mac.c.
Besides, since WMI_REQUEST_RSSI_PER_CHAIN_STAT and WMI_REQUEST_VDEV_STAT stats could also
be requested via mac ops, process them directly in ath11k_update_stats_event().
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.37
Fixes: b488c76644 ("ath11k: report rssi of each chain to mac80211 for QCA6390/WCN6855")
Fixes: c3b39553fc ("ath11k: add signal report to mac80211 for QCA6390 and WCN6855")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250220082448.31039-5-quic_bqiang@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
For WMI_REQUEST_VDEV_STAT request, firmware might split response into
multiple events dut to buffer limit, hence currently in
ath11k_debugfs_fw_stats_process() we wait until all events received.
In case there is no vdev started, this results in that below condition
would never get satisfied
((++ar->fw_stats.num_vdev_recvd) == total_vdevs_started)
finally the requestor would be blocked until wait time out.
The same applies to WMI_REQUEST_BCN_STAT request as well due to:
((++ar->fw_stats.num_bcn_recvd) == ar->num_started_vdevs)
Change to check the number of started vdev first: if it is zero, finish
wait directly; if not, follow the old way.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.37
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250220082448.31039-4-quic_bqiang@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently ath11k_debugfs_fw_stats_process() is using static variables to count
firmware stat events. Taking num_vdev as an example, if for whatever reason (
say ar->num_started_vdevs is 0 or firmware bug etc.) the following condition
(++num_vdev) == total_vdevs_started
is not met, is_end is not set thus num_vdev won't be cleared. Next time when
firmware stats is requested again, even if everything is working fine, we will
fail due to the condition above will never be satisfied.
The same applies to num_bcn as well.
Change to use non-static counters so that we have a chance to clear them each
time firmware stats is requested. Currently only ath11k_fw_stats_request() and
ath11k_debugfs_fw_stats_request() are requesting firmware stats, so clear
counters there.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.37
Fixes: da3a9d3c15 ("ath11k: refactor debugfs code into debugfs.c")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250220082448.31039-3-quic_bqiang@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
We get report [1] that CPU is running a hot loop in
ath11k_debugfs_fw_stats_request():
94.60% 0.00% i3status [kernel.kallsyms] [k] do_syscall_64
|
--94.60%--do_syscall_64
|
--94.55%--__sys_sendmsg
___sys_sendmsg
____sys_sendmsg
netlink_sendmsg
netlink_unicast
genl_rcv
netlink_rcv_skb
genl_rcv_msg
|
--94.55%--genl_family_rcv_msg_dumpit
__netlink_dump_start
netlink_dump
genl_dumpit
nl80211_dump_station
|
--94.55%--ieee80211_dump_station
sta_set_sinfo
|
--94.55%--ath11k_mac_op_sta_statistics
ath11k_debugfs_get_fw_stats
|
--94.55%--ath11k_debugfs_fw_stats_request
|
|--41.73%--_raw_spin_lock_bh
|
|--22.74%--__local_bh_enable_ip
|
|--9.22%--_raw_spin_unlock_bh
|
--6.66%--srso_alias_safe_ret
This is because, if for whatever reason ar->fw_stats_done is not set by
ath11k_update_stats_event(), ath11k_debugfs_fw_stats_request() won't yield
CPU before an up to 3s timeout.
Change to completion mechanism to avoid CPU burning.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.37
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Reported-by: Yury Vostrikov <mon@unformed.ru>
Closes: https://lore.kernel.org/all/7324ac7a-8b7a-42a5-aa19-de52138ff638@app.fastmail.com/ # [1]
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250220082448.31039-2-quic_bqiang@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
the wil6210 driver irq handling code is unconditionally writing
edma irq registers which are supposed to be only used on Talyn chipsets.
This however leade to a chipset hang on the older sparrow chipset
generation and firmware will not even boot.
Fix that by simply checking for edma support before handling these
registers.
Tested on Netgear R9000
Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Link: https://patch.msgid.link/20250304012131.25970-2-s.gottschall@dd-wrt.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In some scenarios, the firmware may be stopped before the interface is
removed, either due to a crash or because the remoteproc (e.g., MPSS)
is shut down early during system reboot or shutdown.
This leads to a delay during interface teardown, as the driver waits for
a vdev delete response that never arrives, eventually timing out.
Example (SNOC):
$ echo stop > /sys/class/remoteproc/remoteproc0/state
[ 71.64] remoteproc remoteproc0: stopped remote processor modem
$ reboot
[ 74.84] ath10k_snoc c800000.wifi: failed to transmit packet, dropping: -108
[ 74.84] ath10k_snoc c800000.wifi: failed to submit frame: -108
[...]
[ 82.39] ath10k_snoc c800000.wifi: Timeout in receiving vdev delete response
To avoid this, skip waiting for the vdev delete response if the firmware is
already marked as unreachable (`ATH10K_FLAG_CRASH_FLUSH`), similar to how
`ath10k_mac_wait_tx_complete()` and `ath10k_vdev_setup_sync()` handle this case.
Signed-off-by: Loic Poulain <loic.poulain@oss.qualcomm.com>
Link: https://patch.msgid.link/20250522131704.612206-1-loic.poulain@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In ath10k_snoc_hif_stop() we skip disabling the IRQs in the crash
recovery flow, but we still unconditionally call enable again in
ath10k_snoc_hif_start().
We can't check the ATH10K_FLAG_CRASH_FLUSH bit since it is cleared
before hif_start() is called, so instead check the
ATH10K_SNOC_FLAG_RECOVERY flag and skip enabling the IRQs during crash
recovery.
This fixes unbalanced IRQ enable splats that happen after recovering from
a crash.
Fixes: 0e622f67e0 ("ath10k: add support for WCN3990 firmware crash recovery")
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Tested-by: Loic Poulain <loic.poulain@oss.qualcomm.com>
Link: https://patch.msgid.link/20250318205043.1043148-1-caleb.connolly@linaro.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
-----BEGIN PGP SIGNATURE-----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=eWJw
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Print the actual delay time in pci_bridge_wait_for_secondary_bus()
instead of assuming it was 1000ms (Wilfred Mallawa)
- Revert 'iommu/amd: Prevent binding other PCI drivers to IOMMU PCI
devices', which broke resume from system sleep on AMD platforms and
has been fixed by other commits (Lukas Wunner)
Resource management:
- Remove mtip32xx use of pcim_iounmap_regions(), which is deprecated
and unnecessary (Philipp Stanner)
- Remove pcim_iounmap_regions() and pcim_request_region_exclusive()
and related flags since all uses have been removed (Philipp
Stanner)
- Rework devres 'request' functions so they are no longer 'hybrid',
i.e., their behavior no longer depends on whether
pcim_enable_device or pci_enable_device() was used, and remove
related code (Philipp Stanner)
- Warn (not BUG()) about failure to assign optional resources (Ilpo
Järvinen)
Error handling:
- Log the DPC Error Source ID only when it's actually valid (when
ERR_FATAL or ERR_NONFATAL was received from a downstream device)
and decode into bus/device/function (Bjorn Helgaas)
- Determine AER log level once and save it so all related messages
use the same level (Karolina Stolarek)
- Use KERN_WARNING, not KERN_ERR, when logging PCIe Correctable
Errors (Karolina Stolarek)
- Ratelimit PCIe Correctable and Non-Fatal error logging, with sysfs
controls on interval and burst count, to avoid flooding logs and
RCU stall warnings (Jon Pan-Doh)
Power management:
- Increment PM usage counter when probing reset methods so we don't
try to read config space of a powered-off device (Alex Williamson)
- Set all devices to D0 during enumeration to ensure ACPI opregion is
connected via _REG (Mario Limonciello)
Power control:
- Rename pwrctrl Kconfig symbols from 'PWRCTL' to 'PWRCTRL' to match
the filename paths. Retain old deprecated symbols for
compatibility, except for the pwrctrl slot driver
(PCI_PWRCTRL_SLOT) (Johan Hovold)
- When unregistering pwrctrl, cancel outstanding rescan work before
cleaning up data structures to avoid use-after-free issues (Brian
Norris)
Bandwidth control:
- Simplify link bandwidth controller by replacing the count of Link
Bandwidth Management Status (LBMS) events with a PCI_LINK_LBMS_SEEN
flag (Ilpo Järvinen)
- Update the Link Speed after retraining, since the Link Speed may
have changed (Ilpo Järvinen)
PCIe native device hotplug:
- Ignore Presence Detect Changed caused by DPC.
pciehp already ignores Link Down/Up events caused by DPC, but on
slots using in-band presence detect, DPC causes a spurious Presence
Detect Changed event (Lukas Wunner)
- Ignore Link Down/Up caused by Secondary Bus Reset.
On hotplug ports using in-band presence detect, the reset causes a
Presence Detect Changed event, which mistakenly caused teardown and
re-enumeration of the device. Drivers may need to annotate code
that resets their device (Lukas Wunner)
Virtualization:
- Add an ACS quirk for Loongson Root Ports that don't advertise ACS
but don't allow peer-to-peer transactions between Root Ports; the
quirk allows each Root Port to be in a separate IOMMU group (Huacai
Chen)
Endpoint framework:
- For fixed-size BARs, retain both the actual size and the possibly
larger size allocated to accommodate iATU alignment requirements
(Jerome Brunet)
- Simplify ctrl/SPAD space allocation and avoid allocating more space
than needed (Jerome Brunet)
- Correct MSI-X PBA offset calculations for DesignWare and Cadence
endpoint controllers (Niklas Cassel)
- Align the return value (number of interrupts) encoding for
pci_epc_get_msi()/pci_epc_ops::get_msi() and
pci_epc_get_msix()/pci_epc_ops::get_msix() (Niklas Cassel)
- Align the nr_irqs parameter encoding for
pci_epc_set_msi()/pci_epc_ops::set_msi() and
pci_epc_set_msix()/pci_epc_ops::set_msix() (Niklas Cassel)
Common host controller library:
- Convert pci-host-common to a library so platforms that don't need
native host controller drivers don't need to include these helper
functions (Manivannan Sadhasivam)
Apple PCIe controller driver:
- Extract ECAM bridge creation helper from pci_host_common_probe() to
separate driver-specific things like MSI from PCI things (Marc
Zyngier)
- Dynamically allocate RID-to_SID bitmap to prepare for SoCs with
varying capabilities (Marc Zyngier)
- Skip ports disabled in DT when setting up ports (Janne Grunau)
- Add t6020 compatible string (Alyssa Rosenzweig)
- Add T602x PCIe support (Hector Martin)
- Directly set/clear INTx mask bits because T602x dropped the
accessors that could do this without locking (Marc Zyngier)
- Move port PHY registers to their own reg items to accommodate
T602x, which moves them around; retain default offsets for existing
DTs that lack phy%d entries with the reg offsets (Hector Martin)
- Stop polling for core refclk, which doesn't work on T602x and the
bootloader has already done anyway (Hector Martin)
- Use gpiod_set_value_cansleep() when asserting PERST# in probe
because we're allowed to sleep there (Hector Martin)
Cadence PCIe controller driver:
- Drop a runtime PM 'put' to resolve a runtime atomic count underflow
(Hans Zhang)
- Make the cadence core buildable as a module (Kishon Vijay Abraham I)
- Add cdns_pcie_host_disable() and cdns_pcie_ep_disable() for use by
loadable drivers when they are removed (Siddharth Vadapalli)
Freescale i.MX6 PCIe controller driver:
- Apply link training workaround only on IMX6Q, IMX6SX, IMX6SP
(Richard Zhu)
- Remove redundant dw_pcie_wait_for_link() from
imx_pcie_start_link(); since the DWC core does this, imx6 only
needs it when retraining for a faster link speed (Richard Zhu)
- Toggle i.MX95 core reset to align with PHY powerup (Richard Zhu)
- Set SYS_AUX_PWR_DET to work around i.MX95 ERR051624 erratum: in
some cases, the controller can't exit 'L23 Ready' through Beacon or
PERST# deassertion (Richard Zhu)
- Clear GEN3_ZRXDC_NONCOMPL to work around i.MX95 ERR051586 erratum:
controller can't meet 2.5 GT/s ZRX-DC timing when operating at 8
GT/s, causing timeouts in L1 (Richard Zhu)
- Wait for i.MX95 PLL lock before enabling controller (Richard Zhu)
- Save/restore i.MX95 LUT for suspend/resume (Richard Zhu)
Mobiveil PCIe controller driver:
- Return bool (not int) for link-up check in
mobiveil_pab_ops.link_up() and layerscape-gen4, mobiveil (Hans
Zhang)
NVIDIA Tegra194 PCIe controller driver:
- Create debugfs directory for 'aspm_state_cnt' only when
CONFIG_PCIEASPM is enabled, since there are no other entries (Hans
Zhang)
Qualcomm PCIe controller driver:
- Add OF support for parsing DT 'eq-presets-<N>gts' property for lane
equalization presets (Krishna Chaitanya Chundru)
- Read Maximum Link Width from the Link Capabilities register if DT
lacks 'num-lanes' property (Krishna Chaitanya Chundru)
- Add Physical Layer 64 GT/s Capability ID and register offsets for
8, 32, and 64 GT/s lane equalization registers (Krishna Chaitanya
Chundru)
- Add generic dwc support for configuring lane equalization presets
(Krishna Chaitanya Chundru)
- Add DT and driver support for PCIe on IPQ5018 SoC (Nitheesh Sekar)
Renesas R-Car PCIe controller driver:
- Describe endpoint BAR 4 as being fixed size (Jerome Brunet)
- Document how to obtain R-Car V4H (r8a779g0) controller firmware
(Yoshihiro Shimoda)
Rockchip PCIe controller driver:
- Reorder rockchip_pci_core_rsts because
reset_control_bulk_deassert() deasserts in reverse order, to fix a
link training regression (Jensen Huang)
- Mark RK3399 as being capable of raising INTx interrupts (Niklas
Cassel)
Rockchip DesignWare PCIe controller driver:
- Check only PCIE_LINKUP, not LTSSM status, to determine whether the
link is up (Shawn Lin)
- Increase N_FTS (used in L0s->L0 transitions) and enable ASPM L0s
for Root Complex and Endpoint modes (Shawn Lin)
- Hide the broken ATS Capability in rockchip_pcie_ep_init() instead
of rockchip_pcie_ep_pre_init() so it stays hidden after PERST#
resets non-sticky registers (Shawn Lin)
- Call phy_power_off() before phy_exit() in rockchip_pcie_phy_deinit()
(Diederik de Haas)
Synopsys DesignWare PCIe controller driver:
- Set PORT_LOGIC_LINK_WIDTH to one lane to make initial link training
more robust; this will not affect the intended link width if all
lanes are functional (Wenbin Yao)
- Return bool (not int) for link-up check in dw_pcie_ops.link_up()
and armada8k, dra7xx, dw-rockchip, exynos, histb, keembay,
keystone, kirin, meson, qcom, qcom-ep, rcar_gen4, spear13xx,
tegra194, uniphier, visconti (Hans Zhang)
- Add debugfs support for exposing DWC device-specific PTM context
(Manivannan Sadhasivam)
TI J721E PCIe driver:
- Make j721e buildable as a loadable and removable module (Siddharth
Vadapalli)
- Fix j721e host/endpoint dependencies that result in link failures
in some configs (Arnd Bergmann)
Device tree bindings:
- Add qcom DT binding for 'global' interrupt (PCIe controller and
link-specific events) for ipq8074, ipq8074-gen3, ipq6018, sa8775p,
sc7280, sc8180x sdm845, sm8150, sm8250, sm8350 (Manivannan
Sadhasivam)
- Add qcom DT binding for 8 MSI SPI interrupts for msm8998, ipq8074,
ipq8074-gen3, ipq6018 (Manivannan Sadhasivam)
- Add dw rockchip DT binding for rk3576 and rk3562 (Kever Yang)
- Correct indentation and style of examples in brcm,stb-pcie,
cdns,cdns-pcie-ep, intel,keembay-pcie-ep, intel,keembay-pcie,
microchip,pcie-host, rcar-pci-ep, rcar-pci-host, xilinx-versal-cpm
(Krzysztof Kozlowski)
- Convert Marvell EBU (dove, kirkwood, armada-370, armada-xp) and
armada8k from text to schema DT bindings (Rob Herring)
- Remove obsolete .txt DT bindings for content that has been moved to
schemas (Rob Herring)
- Add qcom DT binding for MHI registers in IPQ5332, IPQ6018, IPQ8074
and IPQ9574 (Varadarajan Narayanan)
- Convert v3,v360epc-pci from text to DT schema binding (Rob Herring)
- Change microchip,pcie-host DT binding to be 'dma-noncoherent' since
PolarFire may be configured that way (Conor Dooley)
Miscellaneous:
- Drop 'pci' suffix from intel_mid_pci.c filename to match similar
files (Andy Shevchenko)
- All platforms with PCI have an MMU, so add PCI Kconfig dependency
on MMU to simplify build testing and avoid inadvertent build
regressions (Arnd Bergmann)
- Update Krzysztof Wilczyński's email address in MAINTAINERS
(Krzysztof Wilczyński)
- Update Manivannan Sadhasivam's email address in MAINTAINERS
(Manivannan Sadhasivam)"
* tag 'pci-v6.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (147 commits)
MAINTAINERS: Update Manivannan Sadhasivam email address
PCI: j721e: Fix host/endpoint dependencies
PCI: j721e: Add support to build as a loadable module
PCI: cadence-ep: Introduce cdns_pcie_ep_disable() helper for cleanup
PCI: cadence-host: Introduce cdns_pcie_host_disable() helper for cleanup
PCI: cadence: Add support to build pcie-cadence library as a kernel module
MAINTAINERS: Update Krzysztof Wilczyński email address
PCI: Remove unnecessary linesplit in __pci_setup_bridge()
PCI: WARN (not BUG()) when we fail to assign optional resources
PCI: Remove unused pci_printk()
PCI: qcom: Replace PERST# sleep time with proper macro
PCI: dw-rockchip: Replace PERST# sleep time with proper macro
PCI: host-common: Convert to library for host controller drivers
PCI/ERR: Remove misleading TODO regarding kernel panic
PCI: cadence: Remove duplicate message code definitions
PCI: endpoint: Align pci_epc_set_msix(), pci_epc_ops::set_msix() nr_irqs encoding
PCI: endpoint: Align pci_epc_set_msi(), pci_epc_ops::set_msi() nr_irqs encoding
PCI: endpoint: Align pci_epc_get_msix(), pci_epc_ops::get_msix() return value encoding
PCI: endpoint: Align pci_epc_get_msi(), pci_epc_ops::get_msi() return value encoding
PCI: cadence-ep: Correct PBA offset in .set_msix() callback
...
The PCI_PWRCTRL_PWRSEQ and HAVE_PWRCTRL symbols have been renamed to
reflect the pwrctrl framework name. Switch to the non-deprecated symbols.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jeff Johnson <jjohnson@kernel.org> # drivers/net/wireless/ath/...
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://patch.msgid.link/20250402132634.18065-4-johan+linaro@kernel.org
The PCI_PWRCTRL_PWRSEQ and HAVE_PWRCTRL symbols have been renamed to
reflect the pwrctrl framework name. Switch to the non-deprecated symbols.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jeff Johnson <jjohnson@kernel.org> # drivers/net/wireless/ath/...
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://patch.msgid.link/20250402132634.18065-3-johan+linaro@kernel.org
ath12k:
Add monitor mode support for WCN7850.
Enhance regulatory support including 6 GHz power modes.
In addition, perform the usual set of bug fixes and cleanups across
all supported drivers.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQ/mtSHzPUi16IfDEksFbugiYzLewUCaC5IEwAKCRAsFbugiYzL
ezMUAQCAH3sy0hJSraoLb+6+VMI/ClBquJVIgOBwVvlXJd4lIgEAwY+uYgSNWkYU
KQ2Zxa8+whDx6oqFJF5qYJ+scMh9VA0=
=b7Wk
-----END PGP SIGNATURE-----
Merge tag 'ath-next-20250521' of git://git.kernel.org/pub/scm/linux/kernel/git/ath/ath
Jeff Johnson says:
==================
ath.git patches for v6.16
ath12k:
Add monitor mode support for WCN7850.
Enhance regulatory support including 6 GHz power modes.
In addition, perform the usual set of bug fixes and cleanups across
all supported drivers.
==================
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 7ed3e88664 ("wifi: ath12k: update regulatory rules when connection
established") introduced a call to ath12k_reg_handle_chan_list() upon
connection to update the regulatory domain in cfg80211 based on the power
type received from the AP.
However, this update fails because ah->regd_updated was already set to true
during the earlier regulatory update triggered when the interface was
added.
To resolve this, reset ah->regd_updated before calling
ath12k_reg_handle_chan_list() to ensure the update proceeds correctly.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Fixes: 7ed3e88664 ("wifi: ath12k: update regulatory rules when connection established")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250521-ath12k-fix-ah-regd_updated-v1-3-9737de5bf98e@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Commit 4c546023d7 ("wifi: ath12k: update regulatory rules when interface
added"), introduced a call to ath12k_reg_handle_chan_list() during
interface addition to update the regulatory domain based on the interface
type. While this works initially, subsequent updates (e.g., after an
interface delete/re-add cycle) fail because ah->regd_updated is never
reset.
To address this, reset ah->regd_updated before calling
ath12k_reg_handle_chan_list() to allow the update to proceed.
However, this change exposes another issue: a timeout occurs when waiting
for the 11D scan to complete, as seen in the log:
ath12k_pci 0000:05:00.0: failed to receive 11d scan complete: timed out
This happens because during interface down, ar->state_11d is set to
ATH12K_11D_PREPARING, and during interface up, the host waits for
ar->completed_11d_scan even though the scan hasn't started yet.
Fix this by updating the wait condition to check for ATH12K_11D_RUNNING,
which is the only state where a scan complete event is expected.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Fixes: 4c546023d7 ("wifi: ath12k: update regulatory rules when interface added")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250521-ath12k-fix-ah-regd_updated-v1-2-9737de5bf98e@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In the current implementation of ath12k_regd_update(), the ah->regd_updated
flag is used to ensure that the regulatory domain is updated only once per
radio. During MAC registration, this function is called to push the default
regulatory domain to cfg80211. At that point, the hardware state is not on
and hence ah->regd_updated remains false.
However, after commit 4c546023d7 ("wifi: ath12k: update regulatory rules
when interface added"), ath12k_reg_handle_chan_list() is invoked when an
interface is added, which in turn calls ath12k_regd_update(). By this time,
hardware state is on and consecutively ah->regd_updated becomes true.
Later, when the 11D scan completes and a new regulatory domain is received
from the firmware, the host attempts to update cfg80211 again via
ath12k_regd_update(). But since ah->regd_updated is already true, the
update is skipped.
>From the user's perspective, this results in a failure to connect to 6 GHz
APs, as the default regulatory domain (the only one pushed to cfg80211)
does not include 6 GHz support.
To resolve this, reset the ah->regd_updated flag when handling the 11D
regulatory domain update.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Fixes: 591de41d70 ("wifi: ath12k: add 11d scan offload support")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250521-ath12k-fix-ah-regd_updated-v1-1-9737de5bf98e@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Checking the SOCK_WIFI_STATUS flag bit in sk_flags may give wrong results
since sk_flags are part of a union and the union is used otherwise. Add
sk_requests_wifi_status() which checks if sk is non-NULL, sk is a full
socket (so flags are valid) and checks the flag bit.
Fixes: 76a853f86c ("wifi: free SKBTX_WIFI_STATUS skb tx_flags flag")
Suggested-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Bert Karwatzki <spasswolf@web.de>
Reviewed-by: Jason Xing <kerneljasonxing@gmail.com>
Link: https://patch.msgid.link/20250520223430.6875-1-spasswolf@web.de
[edit commit message, fix indentation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current implementation of per-pdev frequency range updates assumes that
each pdev supports only a single band. As a result in ath12k_regd_update(),
bands are handled using an if-else structure, which limits updates to only
one of the band per pdev. This assumption does not hold for all chipsets.
For example, the WCN7850 supports multiple bands within a single pdev.
Hence to accommodate such cases, update the logic to account for all band
cases by handling each band in a separate if conditions instead of the
previous if-else structure.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Fixes: 13324cecbb ("wifi: ath12k: Update frequency range if reg rules changes")
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250520-fix_freq_range_update-v1-1-e061fd147b87@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The function calls bitmap_empty() just before find_first_bit(). Both
functions are O(N). Because find_first_bit() returns >= nbits in case of
empty bitmap, the bitmap_empty() test may be avoided.
Signed-off-by: Yury Norov <yury.norov@gmail.com>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
Link: https://patch.msgid.link/20250326155200.39895-1-yury.norov@gmail.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
A malicious USB device can send a WMI_SWBA_EVENTID event from an
ath9k_htc-managed device before beaconing has been enabled. This causes
a device-by-zero error in the driver, leading to either a crash or an
out of bounds read.
Prevent this by aborting the handling in ath9k_htc_swba() if beacons are
not enabled.
Reported-by: Robert Morris <rtm@csail.mit.edu>
Closes: https://lore.kernel.org/r/88967.1743099372@localhost
Fixes: 832f6a18fc ("ath9k_htc: Add beacon slots")
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://patch.msgid.link/20250402112217.58533-1-toke@toke.dk
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Whenever there is a change in the country code settings from the
user, driver does an intersection of the regulatory rules for this
new country with the original regulatory rules which were reported
during initialization time.
There is also similar logic running in firmware with a difference
that the intersection in firmware is only done when the country code
is configuration during boot up time (BDF/OTP). Firmware logic does
not kick in when no country code is configured during device bring
up time as the device is always expected to have the country code
configured properly in the deployment.
There is a debug/test use case that requires absolute regulatory
rules to be used for a user configured country code when the device
is not configured with a particular country code during boot up time.
To support the above test use case, remove the redundant regulatory
rules intersection logic in the host driver. Depend on the
intersection logic in firmware when the device comes up with
pre-configured country code.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00209-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aishwarya R <quic_aisr@quicinc.com>
Signed-off-by: Rajat Soni <quic_rajson@quicinc.com>
Link: https://patch.msgid.link/20250505034351.1365914-1-quic_rajson@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
As per IEEE 802.11be-2024 - 9.4.2.321, EHT operation element
contains MCS15 Disable subfield as the sixth bit, which is set when
MCS15 support is not enabled.
During association, firmware will use this MCS15 flag to enable or
disable the reception of PPDU with EHT-MCS15 capability.
Send MCS15 support to firmware through WMI command during peer assoc.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Co-developed-by: Dhanavandhana Kannan <quic_dhanavan1@quicinc.com>
Signed-off-by: Dhanavandhana Kannan <quic_dhanavan1@quicinc.com>
Signed-off-by: Mohan Kumar G <quic_mkumarg@quicinc.com>
Link: https://patch.msgid.link/20250505153536.3275145-1-quic_mkumarg@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
During a code review, it is observed that in the scenario
where scan initiation fails, the current code schedules the
ar->scan.timeout workqueue which is not necessary.
In the scan initiation failure scenario, exit the code instead
of scheduling the ar->scan.timeout workqueue.
Compile tested only.
Signed-off-by: Vignesh C <quic_vignc@quicinc.com>
Link: https://patch.msgid.link/20250512065849.2833232-1-quic_vignc@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Users of the Lenovo ThinkPad X13s have reported that Wi-Fi sometimes
breaks and the log fills up with errors like:
ath11k_pci 0006:01:00.0: HTC Rx: insufficient length, got 1484, expected 1492
ath11k_pci 0006:01:00.0: HTC Rx: insufficient length, got 1460, expected 1484
which based on a quick look at the ath11k driver seemed to indicate some
kind of ring-buffer corruption.
Miaoqing Pan tracked it down to the host seeing the updated destination
ring head pointer before the updated descriptor, and the error handling
for that in turn leaves the ring buffer in an inconsistent state.
While this has not yet been observed with ath12k, the ring-buffer
implementation is very similar to the ath11k one and it suffers from the
same bugs.
Add the missing memory barrier to make sure that the descriptor is read
after the head pointer to address the root cause of the corruption while
fixing up the error handling in case there are ever any (ordering) bugs
on the device side.
Note that the READ_ONCE() are only needed to avoid compiler mischief in
case the ring-buffer helpers are ever inlined.
Tested-on: WCN7850 hw2.0 WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Cc: stable@vger.kernel.org # 6.3
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218623
Link: https://lore.kernel.org/20250310010217.3845141-3-quic_miaoqing@quicinc.com
Cc: Miaoqing Pan <quic_miaoqing@quicinc.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Miaoqing Pan <quic_miaoqing@quicinc.com>
Link: https://patch.msgid.link/20250321095219.19369-1-johan+linaro@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
