For scanning purposes, the driver can use link ID 15 (scan link). A future
change will make non-ML interfaces to select the scan link. In this
scenario, arvif->link_id will be used to retrieve the link configuration in
ath12k_mac_vdev_create(). However, link ID 15 is not recognized as a valid
link ID in the upper kernel, which will result in a failure to fetch
link_conf and subsequently cause the scan to fail.
To avoid this issue, ensure link_conf is fetched only when the link ID is
within the valid range. Since link_conf cannot be retrieved using the scan
link, use vif->addr as the Ethernet address for creating the scan vdev.
This address will serve as the source address (address 2) in the probe
request frames during scanning. Additionally, use the automatic Tx power
value for the vdev. As this is a scan vdev, these values do not affect the
scan functionality.
Note that vif->addr will only be taken when a valid link_conf can not be
fetched. Otherwise, link_conf's address will be taken as address 2.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250417-fix_scan_vdev_handling-v3-1-9ec42513d26b@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Read the country code from SMBIOS and send it to the firmware. The
firmware will then indicate the regulatory domain information for
the country code, which ath12k will use.
dmesg:
[ 1242.637253] ath12k_pci 0000:02:00.0: worldwide regdomain setting from SMBIOS
[ 1242.637259] ath12k_pci 0000:02:00.0: bdf variant name not found.
[ 1242.637261] ath12k_pci 0000:02:00.0: SMBIOS bdf variant name not set.
[ 1242.927543] ath12k_pci 0000:02:00.0: set current country pdev id 0 alpha2 00
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-02582-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kang Yang <kang.yang@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250417024227.1712-1-kang.yang@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
ath12k:
Enable AHB support for IPQ5332.
Add monitor interface support to QCN9274.
Add MLO support to WCN7850.
Add 802.11d scan offload support to WCN7850.
ath11k:
Restore hibernation support
In addition, perform the usual set of bug fixes and cleanups across
all supported drivers.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQ/mtSHzPUi16IfDEksFbugiYzLewUCaAJ2WAAKCRAsFbugiYzL
exnBAQDcBNn9WWQnHOIo4YIY//8Rnw311troRh1V/NLNHTaMmAD9G8SCa8qbI/rs
gOxcP5XeDmR3LwKuw4/7emXucX9W+ww=
=mAEA
-----END PGP SIGNATURE-----
Merge tag 'ath-next-20250418' of git://git.kernel.org/pub/scm/linux/kernel/git/ath/ath into wireless-next
Jeff Johnson says:
====================
ath.git patches for v6.16
ath12k:
Enable AHB support for IPQ5332.
Add monitor interface support to QCN9274.
Add MLO support to WCN7850.
Add 802.11d scan offload support to WCN7850.
ath11k:
Restore hibernation support
In addition, perform the usual set of bug fixes and cleanups across
all supported drivers.
====================
Change-Id: I6555e64d7434f3a5fed5faab25057be93106b18e
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For MBSSID, each vif (struct ieee80211_vif) stores another vif
pointer for the transmitting profile of MBSSID set. This won't
suffice for MLO as there may be multiple links, each of which can
be part of different MBSSID sets. Hence the information needs to
be stored per-link. Additionally, the transmitted profile itself
may be part of an MLD hence storing vif will not suffice either.
Fix MLO by storing an instance of struct ieee80211_bss_conf
for each link.
Modify following operations to reflect the above structure updates:
- channel switch completion
- BSS color change completion
- Removing nontransmitted links in ieee80211_stop_mbssid()
- drivers retrieving the transmitted link for beacon templates.
Signed-off-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Co-developed-by: Muna Sinada <muna.sinada@oss.qualcomm.com>
Signed-off-by: Muna Sinada <muna.sinada@oss.qualcomm.com>
Co-developed-by: Aloka Dixit <aloka.dixit@oss.qualcomm.com>
Signed-off-by: Aloka Dixit <aloka.dixit@oss.qualcomm.com>
Link: https://patch.msgid.link/20250408184501.3715887-3-aloka.dixit@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Jason mentioned at netdevconf that we've run out of tx_flags in
the skb_shinfo(). Gain one bit back by removing the wifi bit.
We can do that because the only userspace application for it
(hostapd) doesn't change the setting on the socket, it just
uses different sockets, and normally doesn't even use this any
more, sending the frames over nl80211 instead.
Reviewed-by: Jason Xing <kerneljasonxing@gmail.com>
Link: https://patch.msgid.link/20250313134942.52ff54a140ec.If390bbdc46904cf451256ba989d7a056c457af6e@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the past %pK was preferable to %p as it would not leak raw pointer
values into the kernel log.
Since commit ad67b74d24 ("printk: hash addresses printed with %p")
the regular %p has been improved to avoid this issue.
Furthermore, restricted pointers ("%pK") were never meant to be used
through printk(). They can still unintentionally leak raw pointers or
acquire sleeping looks in atomic contexts.
Switch to the regular pointer formatting which is safer and
easier to reason about.
There are still a few users of %pK left, but these use it through seq_file,
for which its usage is safe.
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Acked-by: Loic Poulain <loic.poulain@oss.qualcomm.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Link: https://patch.msgid.link/20250417-restricted-pointers-ath-v1-4-4e9a04dbe362@linutronix.de
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In the past %pK was preferable to %p as it would not leak raw pointer
values into the kernel log.
Since commit ad67b74d24 ("printk: hash addresses printed with %p")
the regular %p has been improved to avoid this issue.
Furthermore, restricted pointers ("%pK") were never meant to be used
through printk(). They can still unintentionally leak raw pointers or
acquire sleeping looks in atomic contexts.
Switch to the regular pointer formatting which is safer and
easier to reason about.
There are still a few users of %pK left, but these use it through seq_file,
for which its usage is safe.
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Link: https://patch.msgid.link/20250417-restricted-pointers-ath-v1-3-4e9a04dbe362@linutronix.de
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In the past %pK was preferable to %p as it would not leak raw pointer
values into the kernel log.
Since commit ad67b74d24 ("printk: hash addresses printed with %p")
the regular %p has been improved to avoid this issue.
Furthermore, restricted pointers ("%pK") were never meant to be used
through printk(). They can still unintentionally leak raw pointers or
acquire sleeping looks in atomic contexts.
Switch to the regular pointer formatting which is safer and
easier to reason about.
There are still a few users of %pK left, but these use it through seq_file,
for which its usage is safe.
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Link: https://patch.msgid.link/20250417-restricted-pointers-ath-v1-2-4e9a04dbe362@linutronix.de
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In the past %pK was preferable to %p as it would not leak raw pointer
values into the kernel log.
Since commit ad67b74d24 ("printk: hash addresses printed with %p")
the regular %p has been improved to avoid this issue.
Furthermore, restricted pointers ("%pK") were never meant to be used
through printk(). They can still unintentionally leak raw pointers or
acquire sleeping looks in atomic contexts.
Switch to the regular pointer formatting which is safer and
easier to reason about.
There are still a few users of %pK left, but these use it through seq_file,
for which its usage is safe.
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Link: https://patch.msgid.link/20250417-restricted-pointers-ath-v1-1-4e9a04dbe362@linutronix.de
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In current WLAN recovery code flow, ath12k_core_halt() only reinitializes
the "arvifs" list head. This will cause the list node immediately following
the list head to become an invalid list node. Because the prev of that node
still points to the list head "arvifs", but the next of the list head
"arvifs" no longer points to that list node.
When a WLAN recovery occurs during the execution of a vif removal, and it
happens before the spin_lock_bh(&ar->data_lock) in
ath12k_mac_vdev_delete(), list_del() will detect the previously mentioned
situation, thereby triggering a kernel panic.
The fix is to remove and reinitialize all vif list nodes from the list head
"arvifs" during WLAN halt. The reinitialization is to make the list nodes
valid, ensuring that the list_del() in ath12k_mac_vdev_delete() can execute
normally.
Call trace:
__list_del_entry_valid_or_report+0xd4/0x100 (P)
ath12k_mac_remove_link_interface.isra.0+0xf8/0x2e4 [ath12k]
ath12k_scan_vdev_clean_work+0x40/0x164 [ath12k]
cfg80211_wiphy_work+0xfc/0x100
process_one_work+0x164/0x2d0
worker_thread+0x254/0x380
kthread+0xfc/0x100
ret_from_fork+0x10/0x20
The change is mostly copied from the ath11k patch:
https://lore.kernel.org/all/20250320053145.3445187-1-quic_stonez@quicinc.com/
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: Maharaja Kennadyrajan <maharaja.kennadyrajan@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250416021724.2162519-1-maharaja.kennadyrajan@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
ath12k_mac_mgmt_tx_wmi() fetches ath12k's skb_cb space multiple times from
TX skb which is redundant operation. Save the skb_cb in a local pointer
and use the same instead.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250415195812.2633923-3-rameshkumar.sundaram@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently for CCMP256, GCMP128 and GCMP256 ciphers, in
ath12k_install_key() IEEE80211_KEY_FLAG_GENERATE_IV_MGMT is not set and
in ath12k_mac_mgmt_tx_wmi() a length of IEEE80211_CCMP_MIC_LEN is reserved
for all ciphers.
This results in unexpected drop of protected management frames in case
either of above 3 ciphers is used. The reason is, without
IEEE80211_KEY_FLAG_GENERATE_IV_MGMT set, mac80211 will not generate
CCMP/GCMP headers in TX frame for ath12k.
Also MIC length reserved is wrong and such frames are dropped by hardware.
Fix this by setting IEEE80211_KEY_FLAG_GENERATE_IV_MGMT flag for above
ciphers and by reserving proper MIC length for those ciphers.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250415195812.2633923-2-rameshkumar.sundaram@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, in the mac80211 layer, received EAPOL packets are dropped
when the HT control field is present in the QoS header. This issue
arises due to an incorrect QoS control field offset used to build
the QoS header in the MSDU data, leading to a corrupted header in the
mac80211 layer. This issue also applies to other frames that contain
the QoS control field, such as QoS data or Null frames. To resolve
this, use ieee80211_get_qos_ctl() to obtain the correct QoS control
offset from the MSDU data. Additionally, ensure the QoS control header
is copied in little-endian format within the MSDU data.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: Ramasamy Kaliappan <quic_rkaliapp@quicinc.com>
Signed-off-by: Nithyanantham Paramasivam <nithyanantham.paramasivam@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250415184102.2707300-1-nithyanantham.paramasivam@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, driver allocates the struct ath12k_rx_peer_stats for each
station regardless of whether ext_rx_stats is enabled. This structure
is populated by the monitor destination ring for both single-user and
multi-user scenarios when ext_rx_stats is enabled. However, when
ext_rx_stats is disabled, this allocation is unnecessary and results in
additional memory consumption.
To address this issue, allocate the struct ath12k_rx_peer_stats only when
ext_rx_stats is enabled through debugfs. This change prevents unnecessary
memory allocation. Additionally, ensure that the station dump RSSI is
updated irrespective of the ext_rx_stats enablement.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: P Praneesh <praneesh.p@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250409052647.81955-1-praneesh.p@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Running this test in a loop it is easy to reproduce an rtnl deadlock:
iw reg set FI
ifconfig wlan0 down
What happens is that thread A (workqueue) tries to update the regulatory:
try to acquire the rtnl_lock of ar->regd_update_work
rtnl_lock
ath12k_regd_update [ath12k]
ath12k_regd_update_work [ath12k]
process_one_work
worker_thread
kthread
ret_from_fork
And thread B (ifconfig) tries to stop the interface:
try to cancel_work_sync(&ar->regd_update_work) in ath12k_mac_op_stop().
ifconfig 3109 [003] 2414.232506: probe:
ath12k_mac_op_stop [ath12k]
drv_stop [mac80211]
ieee80211_do_stop [mac80211]
ieee80211_stop [mac80211]
The sequence of deadlock is:
1. Thread B calls rtnl_lock().
2. Thread A starts to run and calls rtnl_lock() from within
ath12k_regd_update_work(), then enters wait state because the lock is
owned by thread B.
3. Thread B tries to call cancel_work_sync(&ar->regd_update_work), but
thread A is in ath12k_regd_update_work() waiting for rtnl_lock(). So
cancel_work_sync() forever waits for ath12k_regd_update_work() to
finish and we have a deadlock.
Change to use regulatory_set_wiphy_regd(), which is the asynchronous
version of regulatory_set_wiphy_regd_sync(). This way rtnl & wiphy locks
are not required so can be removed, and in the end the deadlock issue can
be avoided.
But a side effect introduced by the asynchronous regd update is that,
some essential information used in ath12k_reg_update_chan_list(), which
would be called later in ath12k_regd_update(), might has not been updated
by cfg80211, as a result wrong channel parameters sent to firmware.
To handle this side effect, move ath12k_reg_update_chan_list() to
ath12k_reg_notifier(), and advertise WIPHY_FLAG_NOTIFY_REGDOM_BY_DRIVER
to cfg80211. This works because, in the process of the asynchronous regd
update, after the new regd is processed, cfg80211 will notify ath12k by
calling ath12k_reg_notifier(). Since all essential information is updated
at that time, we are good to do channel list update.
Please note ath12k_reg_notifier() could also be called due to other
reasons, like core/beacon/user hints etc. For them we are not allowed to
call ath12k_reg_update_chan_list() because regd has not been updated.
This is done by verifying the initiator.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Co-developed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Reviewed-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250408-rtnl-deadlock-v3-1-fdc12bc511ea@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In the WBM error path, while processing TKIP MIC errors, MSDU length
is fetched from the hal_rx_desc's msdu_end. This MSDU length is
directly passed to skb_put() without validation. In stress test
scenarios, the WBM error ring may receive invalid descriptors, which
could lead to an invalid MSDU length.
To fix this, add a check to drop the skb when the calculated MSDU
length is greater than the skb size.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: Nithyanantham Paramasivam <nithyanantham.paramasivam@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250416021903.3178962-1-nithyanantham.paramasivam@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In ath12k_dp_rx_msdu_coalesce(), rxcb is fetched from skb and boolean
is_continuation is part of rxcb.
Currently, after freeing the skb, the rxcb->is_continuation accessed
again which is wrong since the memory is already freed.
This might lead use-after-free error.
Hence, fix by locally defining bool is_continuation from rxcb,
so that after freeing skb, is_continuation can be used.
Compile tested only.
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: Sarika Sharma <quic_sarishar@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250408045327.1632222-1-quic_sarishar@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, RX is_mcbc bit is set for packets sent from client as
destination address (DA) is multicast/broadcast address, but packets
are actually unicast as receiver address (RA) is not multicast address.
Hence, packets are not handled properly due to this is_mcbc bit.
Therefore, reset the is_mcbc bit if interface type is AP.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sarika Sharma <quic_sarishar@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250411061523.859387-3-quic_sarishar@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, the RX multicast broadcast packet check is performed using
bit 15 from the info6 field of the MPDU start descriptor. This check
can also be done using bit 9 from the info5 field of the MSDU end
descriptor. However, in some scenarios multicast bit is not set when
fetched from MPDU start descriptor.
Therefore, checking the RX multicast broadcast packet from the MSDU
end descriptor is more reliable as it is per MSDU.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sarika Sharma <quic_sarishar@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250411061523.859387-2-quic_sarishar@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
During the hardware register, driver updates the frequency range
during boot-up. However, if new regulatory rules are applied after
boot-up, the frequency range remains based on the older rules.
Since different countries have varying regulatory rules, the
frequency range can differ. Retaining the frequency range based on
outdated rules can be misleading.
Update the frequency range according to the new regulatory rules in
the function ath12k_regd_update().
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Co-developed-by: Rajat Soni <quic_rajson@quicinc.com>
Signed-off-by: Rajat Soni <quic_rajson@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250408042128.720263-4-quic_rajson@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
During the initial WMI exchange, the firmware updates the
hardware-supported start and end frequencies in the
ath12k_wmi_hal_reg_capabilities_ext_arg structure. These frequencies,
being hardware-supported, may not always align with the current
regulatory operating frequencies. When operating as multiple grouped
hardwares under a single wiphy, the driver advertises these values
directly to the upper layer in the per-radio frequency range,
which can be misleading.
Sample output snippet from iw phyX info command -
[..]
Supported wiphy radios:
* Idx 0:
Frequency Range: 2312 MHz - 2732 MHz
[..]
* Idx 1:
Frequency Range: 5150 MHz - 5330 MHz
[..]
[..]
The frequency range displayed above is incorrect because the driver
directly advertises the hardware-supported values to the upper layer.
The driver is aware of the current operating regulatory rules, and
hence it can use this information to determine the final operating
start and end frequencies.
To resolve this issue, add support to store the start and end
frequencies received during the regulatory update event.
Then, intersect these with the hardware-supported start and
end frequencies, and finally, advertise the intersected values to the
upper layer.
Sample output snippet from iw phyX info command after the fix -
[..]
Supported wiphy radios:
* Idx 0:
Frequency Range: 2402 MHz - 2472 MHz
[..]
* Idx 1:
Frequency Range: 5170 MHz - 5330 MHz
[..]
[..]
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Co-developed-by: Rajat Soni <quic_rajson@quicinc.com>
Signed-off-by: Rajat Soni <quic_rajson@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250408042128.720263-3-quic_rajson@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In a subsequent change, the frequency range needs to be updated with
each regulatory update. Since the current function also modifies the
DISABLED flag in the actual channel list, which should always align
with hardware-supported start and end frequencies rather than the
current operating ones, the existing function cannot be called again.
Therefore, the logic for setting the frequency range needs to be
refactored.
To address this, refactor the frequency setting part into a new
helper function, ath12k_mac_update_freq_range(). Since this needs
to be done independently of updating the DISABLED flag, call the new
helper function ath12k_mac_update_freq_range() after updating the
channel list for each band.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Rajat Soni <quic_rajson@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250408042128.720263-2-quic_rajson@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
During dma_unmap_single() for extended skb, the driver currently uses
sizeof() of the corresponding structure. When the allocation size changes,
one of the parameters of dma_unmap_single() needs to be updated everywhere.
Improve code readability by using skb->len instead of sizeof() the structure.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: P Praneesh <praneesh.p@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250411060154.1388159-5-praneesh.p@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In ath12k_dp_tx(), memory allocated for extended skb is not freed
properly, causing a memory leak even when the host receives tx
completion for those skbs. Fix this issue by storing skb_ext_desc
in the host tx descriptor and using this skb_ext_desc field during
completion or during ath12k_dp_cc_cleanup().
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: P Praneesh <praneesh.p@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250411060154.1388159-4-praneesh.p@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Current code uses mac_id and msdu parameters in ath12k_dp_tx_free_txbuf()
and ath12k_dp_tx_process_htt_tx_complete(). Since these parameters are
already encapsulated by struct ath12k_dp_tx_desc, passing them individually
results in redundant arguments.
Introduce struct ath12k_tx_desc_params to capture the skb, mac_id, and pass
it to the corresponding functions. Refactor these functions to use struct
ath12k_tx_desc_params instead, reducing the number of arguments and improving
function argument handling efficiency. Additionally, use struct
ath12k_tx_desc_params in ath12k_dp_tx_htt_tx_complete_buf() and
ath12k_dp_tx_complete_msdu(), which will be utilized for fetching extended skb
in a future patch.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: P Praneesh <praneesh.p@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250411060154.1388159-3-praneesh.p@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, in the case of extended skb allocation, the buffer is freed
before the DMA unmap operation. This premature deletion can result in
skb->data corruption, as the memory region could be re-allocated for other
purposes. Fix this issue by reordering the failure cases by calling
dma_unmap_single() first, then followed by the corresponding kfree_skb().
This helps avoid data corruption in case of failures in dp_tx().
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: P Praneesh <praneesh.p@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250411060154.1388159-2-praneesh.p@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
For single pdev device, radio number of a device is forced as 1 in
ath12k_wmi_ext_soc_hal_reg_caps_parse(). This leads to ah->num_radio == 1
and then in ath12k_mac_setup_iface_combinations() we report to
mac/cfg80211 that only 1 channel is supported. In MLO case, it finally
results in failing to bring up the second link as it is in another
channel.
Change num_different_channels to 2 to allow a second link. Since DFS on
multiple channels are not supported yet, remove radar_detect_widths.
For now WCN7850 is the only single pdev device, so others should not be
affected.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00209-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250409-ath12k-wcn7850-mlo-support-v2-9-3801132ca2c3@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The primary link check bypasses REO queue setup for non-primary links
in ath12k_dp_rx_peer_tid_setup(), this works for QCN9274 but breaks
WCN7850 as WCN7850 needs it to be done for each link peer.
Add a new hardware parameter to differentiate them.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00209-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250409-ath12k-wcn7850-mlo-support-v2-8-3801132ca2c3@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In MLO case, all link peers share the same REO queue, so the queue
should be allocated only once, currently this is done by checking
primary_link flag in ath12k_dp_rx_peer_tid_setup(). However, the
check not only avoids duplicate allocation, but also bypasses sending
queue configuration to firmware for non-primary links. In an upcoming
patch, changes will be added to make this check no-ops for WCN7850,
as WCN7850 firmware needs to be explicitly notified each link peer's
queue configuration. That said, the duplicate allocation would arise
again after that change, hence it needs to be resolved before hand.
Since all link peers share the same queue, it should be allocated per
MLD peer, not per link peer. So change to do allocation once and save
it in MLD peer, link peers can simply get queue configuration from
there.
Also relocate ath12k_reoq_buf structure to core.h to avoid circular
dependency.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00209-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250409-ath12k-wcn7850-mlo-support-v2-7-3801132ca2c3@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently vaddr, paddr and size fields are located together with other
fields in ath12k_dp_rx_tid structure. Logically they represents the
REO queue buffer so better to group them in an individual structure.
Introduce a new structure ath12k_reoq_buf to group them. This improves
code readability, and benefits the upcoming patch where this structure
is heavily accessed.
While at it, change vaddr type to 'void *' since it is actually not
pointing to any u32 buffer. Also rename paddr as paddr_aligned to better
reflect its actual meaning.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00209-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250409-ath12k-wcn7850-mlo-support-v2-6-3801132ca2c3@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In MLO scenario WCN7850 firmware requests the assoc link to associate
before any other links. However currently in
ath12k_mac_op_vif_cfg_changed() we are doing association in an ascending
order of link id. If the assoc link does not get assigned the smallest
id, a non-assoc link gets associated first and firmware crashes.
Change to do association for the assoc link first.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00209-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250409-ath12k-wcn7850-mlo-support-v2-5-3801132ca2c3@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In MLO scenario, for station mode interface, WCN7850 firmware requests
the assoc link vdev to get started before any other link vdevs starts.
Firmware internally checks assoc_link field of
wmi_vdev_start_mlo_params.flags when the first vdev starts. And if the
check fails firmware crashes.
Current connection flow guarantees the assoc link vdev gets started
first (at assoc stage only one link vdev is created/started, i.e. the
assoc link vdev), however the assoc_link flag is never set, resulting
in WCN7850 firmware crash.
Note ath12k_link_sta structure already has is_assoc_link flag, and it
is properly set for assoc link. However we can not use it because it
won't be available before peer gets created, which is too late for vdev
starts.
So add a new flag 'is_sta_assoc_link' in ath12k_link_vif structure and
set it when deflink vdev is created. This is valid because we always
use deflink as the assoc link. This flag is passed to firmware vdev
starts to avoid firmware crash. Also verify the link vif/sta pair has
the same settings when creating link sta.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00209-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250409-ath12k-wcn7850-mlo-support-v2-4-3801132ca2c3@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently firmware MLO capability is validated via firmware IE, however
WCN7850 firmware does not support this method but instead advertises
MLO by single_chip_mlo_support bit in QMI phy capability message.
Change to consider single_chip_mlo_support bit as well for MLO capability
validation.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00209-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250409-ath12k-wcn7850-mlo-support-v2-3-3801132ca2c3@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently fw_features is used to check if a specific feature is supported
or not: if the feature bit is set the feature is believed to be supported,
otherwise not supported. Since fw_features is populated only when using
firmware API-2, and by default it is zero, in case of API-1 such as
WCN7850 firmware it is possible that a feature is not enabled by host
while actually firmware supports it.
To avoid this, add a new flag indicating whether fw_features has been ever
populated or not, and only when that flag is true we choose to believe
fw_features. This benefits firmware MLO capability validation in an
upcoming patch.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00209-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250409-ath12k-wcn7850-mlo-support-v2-2-3801132ca2c3@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
There are several places checking if a specific bit set in
ab->fw.fw_features, and in an upcoming patch additional check needs to be
added at all places.
Introduce a new helper ath12k_fw_feature_supported() to avoid code
duplication.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00209-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250409-ath12k-wcn7850-mlo-support-v2-1-3801132ca2c3@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
When operating with multiple devices grouped together, the firmware stores
data related to the state machine of each partner device in the MLO global
memory region. If the firmware crashes, it updates the state to 'crashed'.
During recovery, this memory is shared with the firmware again, and upon
detecting the 'crashed' state, it reasserts. This leads to a loop of
firmware asserts and it never recovers.
Hence to fix this issue, once all devices in the group have been asserted
and powered down, reset the MLO global memory region.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250408-fix_reboot_issues_with_hw_grouping-v4-9-95e7bf048595@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, in ath12k_core_reset(), the device is powered up immediately
after a power down. However, with hardware grouping, when one device
asserts, all partner devices also asserts. If there is a delay in
processing these asserts, by the time this device powers up, other devices
might still be asserting, leading to an overall recovery failure.
To prevent this issue, ensure all asserts for a group are processed before
initiating the power-up sequence.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250408-fix_reboot_issues_with_hw_grouping-v4-8-95e7bf048595@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, when ath12k_core_restart() is called and the ab->is_reset flag
is set, it invokes ieee80211_restart_hw() for all hardware in the same
group. However, other hardware might still be in the recovery process,
making this call inappropriate with grouping into picture.
To address this, add a condition to check if the group is ready. If the
group is not ready, do not call ieee80211_restart_hw().
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250408-fix_reboot_issues_with_hw_grouping-v4-7-95e7bf048595@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, ath12k_core_pre_reconfigure_recovery() reconfigures all radios
within the same group. During grouping and driver going for a recovery,
this function is called as many times as there are devices in the group.
Consequently, it performs the same reconfiguration multiple times, which
is unnecessary.
To prevent this, add a check to continue if the action has already been
taken.
To simplify the management of various flags, the reason for hardware queues
being stopped is used as a check instead of introducing a new flag.
While at it, also add missing wiphy locks. Wiphy lock is required since
ath12k_mac_drain_tx() which is called by
ath12k_core_pre_reconfigure_recovery() needs this lock to be held by the
caller.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250408-fix_reboot_issues_with_hw_grouping-v4-6-95e7bf048595@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
At present, during PCI shutdown, the power down is only executed for a
single device. However, when operating in a group, all devices need to be
powered down simultaneously. Failure to do so will result in a firmware
assertion.
Hence, introduce a new ath12k_pci_hw_group_power_down() and call it during
power down. This will ensure that all partner devices are properly powered
down.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250408-fix_reboot_issues_with_hw_grouping-v4-5-95e7bf048595@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Commit a5686ae820 ("wifi: ath12k: move ATH12K_FLAG_REGISTERED handling to
ath12k_mac_register()") relocated the setting of the ATH12K_FLAG_REGISTERED
flag to the ath12k_mac_register() function. However, this function only
accesses the first device (ab) via ag->ab[0], resulting in the flag being
set only for the first device in the group. Similarly,
ath12k_mac_unregister() only unsets the flag for the first device. The flag
should actually be set for all devices in the group to avoid issues during
recovery.
Hence, move setting and clearing of this flag in the function
ath12k_core_hw_group_start() and ath12k_core_hw_group_stop() respectively.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: a5686ae820 ("wifi: ath12k: move ATH12K_FLAG_REGISTERED handling to ath12k_mac_register()")
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250408-fix_reboot_issues_with_hw_grouping-v4-4-95e7bf048595@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
With hardware grouping, during reboot, whenever a device is removed, it
powers down itself and all its partner devices in the same group. Now this
is done by all devices and hence there is multiple power down for devices
and hence the following error messages can be seen:
ath12k_pci 0002:01:00.0: failed to set mhi state POWER_OFF(3) in current mhi state (0x0)
ath12k_pci 0002:01:00.0: failed to set mhi state: POWER_OFF(3)
ath12k_pci 0002:01:00.0: failed to set mhi state DEINIT(1) in current mhi state (0x0)
ath12k_pci 0002:01:00.0: failed to set mhi state: DEINIT(1)
ath12k_pci 0003:01:00.0: failed to set mhi state POWER_OFF(3) in current mhi state (0x0)
ath12k_pci 0003:01:00.0: failed to set mhi state: POWER_OFF(3)
ath12k_pci 0003:01:00.0: failed to set mhi state DEINIT(1) in current mhi state (0x0)
ath12k_pci 0003:01:00.0: failed to set mhi state: DEINIT(1)
ath12k_pci 0004:01:00.0: failed to set mhi state POWER_OFF(3) in current mhi state (0x0)
ath12k_pci 0004:01:00.0: failed to set mhi state: POWER_OFF(3)
To prevent this, check if the ATH12K_PCI_FLAG_INIT_DONE flag is already
set before powering down. If it is set, it indicates that another partner
device has already performed the power down, and this device can skip this
step.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250408-fix_reboot_issues_with_hw_grouping-v4-3-95e7bf048595@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, driver does not manage reference counting for attaching and
detaching cores to/from hardware groups. This can lead to issues when
multiple cores are involved. Or with same core, attach/detach is called
multiple times back to back.
Fix this issue by using reference counting.
With that, it is now ensured that the core is properly attached or detached
from the hardware group and even back to back calls will not alter the
count.
Additionally, add some debug logs during the attachment and detachment
events for better debugging and tracking.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250408-fix_reboot_issues_with_hw_grouping-v4-2-95e7bf048595@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
During rmmod of ath12k module with SLUB debug enabled, following print is
seen -
=============================================================================
BUG kmalloc-1k (Not tainted): Object already free
-----------------------------------------------------------------------------
Allocated in ath12k_reg_build_regd+0x94/0xa20 [ath12k] age=10470 cpu=0 pid=0
__kmalloc_noprof+0xf4/0x368
ath12k_reg_build_regd+0x94/0xa20 [ath12k]
ath12k_wmi_op_rx+0x199c/0x2c14 [ath12k]
ath12k_htc_rx_completion_handler+0x398/0x554 [ath12k]
ath12k_ce_per_engine_service+0x248/0x368 [ath12k]
ath12k_pci_ce_workqueue+0x28/0x50 [ath12k]
process_one_work+0x14c/0x28c
bh_worker+0x22c/0x27c
workqueue_softirq_action+0x80/0x90
tasklet_action+0x14/0x3c
handle_softirqs+0x108/0x240
__do_softirq+0x14/0x20
Freed in ath12k_reg_free+0x40/0x74 [ath12k] age=136 cpu=2 pid=166
kfree+0x148/0x248
ath12k_reg_free+0x40/0x74 [ath12k]
ath12k_core_hw_group_destroy+0x68/0xac [ath12k]
ath12k_core_deinit+0xd8/0x124 [ath12k]
ath12k_pci_remove+0x6c/0x130 [ath12k]
pci_device_remove+0x44/0xe8
device_remove+0x4c/0x80
device_release_driver_internal+0x1d0/0x22c
driver_detach+0x50/0x98
bus_remove_driver+0x70/0xf4
driver_unregister+0x30/0x60
pci_unregister_driver+0x24/0x9c
ath12k_pci_exit+0x18/0x24 [ath12k]
__arm64_sys_delete_module+0x1a0/0x2a8
invoke_syscall+0x48/0x110
el0_svc_common.constprop.0+0x40/0xe0
Slab 0xfffffdffc0033600 objects=10 used=6 fp=0xffff000000cdcc00 flags=0x3fffe0000000240(workingset|head|node=0|zone=0|lastcpupid=0x1ffff)
Object 0xffff000000cdcc00 @offset=19456 fp=0xffff000000cde400
[...]
This issue arises because in ath12k_core_hw_group_destroy(), each device
calls ath12k_core_soc_destroy() for itself and all its partners within the
same group. Since ath12k_core_hw_group_destroy() is invoked for each
device, this results in a double free condition, eventually causing the
SLUB bug.
To resolve this, set the freed pointers to NULL. And since there could be
a race condition to read these pointers, guard these with the available
mutex lock.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: 6f245ea0ec ("wifi: ath12k: introduce device group abstraction")
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250408-fix_reboot_issues_with_hw_grouping-v4-1-95e7bf048595@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
If the user tries to write more than 32 bytes then it results in memory
corruption. Fortunately, this is debugfs so it's limited to root users.
Fixes: 3f73c24f28 ("wifi: ath12k: Add support to enable debugfs_htt_stats")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/35daefbd-d493-41d9-b192-96177d521b40@stanley.mountain
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The devm_memremap() function returns error pointers on error and the
ioremap() function returns NULL on error. The error checking here got
those flipped around.
Fixes: c01d5cc9b9 ("wifi: ath12k: Power up userPD")
Fixes: 6cee30f0da ("wifi: ath12k: add AHB driver support for IPQ5332")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/937abc74-9648-4c05-a2c3-8db408b3ed9e@stanley.mountain
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The use of of_property_read_u32() isn't really correct as
"memory-region" contains phandles (though those happen to be u32s. As
it is just testing for property presence, use of_property_present()
instead.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20250408190211.2505737-2-robh@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Incorrect WMI tag is used for EHT rate update from host to firmware
while encoding peer assoc WMI.
Correct the WMI tag used for EHT rate update from WMI_TAG_HE_RATE_SET
to the proper tag. This ensures firmware does not mistakenly update HE rate during parsing.
Found during code review. Compile tested only.
Fixes: 5b70ec6036 ("wifi: ath12k: add WMI support for EHT peer")
Signed-off-by: Ramya Gnanasekar <ramya.gnanasekar@oss.qualcomm.com>
Link: https://patch.msgid.link/20250409152341.944628-1-ramya.gnanasekar@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, the AP does not support the broadcast target wake time (TWT)
feature. Therefore, disable the broadcast TWT feature in the HE MAC
capabilities element field.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00209-QCAHKSWPL_SILICONZ-1
Signed-off-by: Thomas Wu <quic_wthomas@quicinc.com>
Signed-off-by: Aaradhana Sahu <aaradhana.sahu@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250409053830.4039467-1-aaradhana.sahu@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, ahvif->key_cipher is compared with the enum value
(WMI_CIPHER_NONE) inside ath12k_mac_op_tx(). However, ahvif->key_cipher is
set using the macro value WLAN_CIPHER_SUITE_XXXX which seems inconsistent.
To improve code consistency and readability, introduce check against zero
for ahvif->key_cipher instead of comparing it with the enum
(WMI_CIPHER_NONE).
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00209-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aaradhana Sahu <aaradhana.sahu@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250403082207.3323938-3-aaradhana.sahu@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, the key_cipher in the ath12k_vif structure, which represents the
group cipher of the MLD AP, is populated when the link address matches the
ieee80211_vif address within ath12k_install_key().
However, in MLD AP, the link address and ieee80211_vif address can differ.
Due to this key_cipher is not populated and multicast packets don't get the
correct cipher information and resulting multicast packets drop.
To fix this, compare the link address with the arvif->bssid instead of the
ieee80211_vif address.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00209-QCAHKSWPL_SILICONZ-1
Fixes: 3dd2c68f20 ("wifi: ath12k: prepare vif data structure for MLO handling")
Signed-off-by: Aaradhana Sahu <aaradhana.sahu@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250403082207.3323938-2-aaradhana.sahu@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, the 'err_pci_msi_free' label is misplaced, causing the cleanup
sequence to be incorrect. Fix this by moving the 'err_pci_msi_free' label
to the correct position after 'err_irq_affinity_cleanup'.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00209-QCAHKSWPL_SILICONZ-1
Fixes: a3012f206d ("wifi: ath12k: set IRQ affinity to CPU0 in case of one MSI vector")
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250403-ath12k-cleanup-v1-1-ad8f67b0e9cf@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In ath12k_dp_rx_h_mpdu(), during the undecap to native wifi mode, the rx
descriptor memory is overwritten. After this function call, any subsequent
accesses to rx descriptor related memory yield invalid values. Fix this by
replacing instances where rx_desc was used with the pre-cached information
in rx_info. This ensures that the values populated from the rx descriptor
are accurate and prevents invalid memory access.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Co-developed-by: Karthikeyan Periyasamy <karthikeyan.periyasamy@oss.qualcomm.com>
Signed-off-by: Karthikeyan Periyasamy <karthikeyan.periyasamy@oss.qualcomm.com>
Signed-off-by: P Praneesh <praneesh.p@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250402182917.2715596-3-praneesh.p@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In ath12k_dp_rx_h_mpdu(), as part of undecap to native wifi mode, the rx
descriptor memory is getting overwritten. After this function call, all
the rx descriptor related memory accesses give invalid values. To handle
this scenario, introduce a new structure ath12k_dp_rx_info which
pre-caches all the required fields from the rx descriptor before calling
ath12k_dp_rx_h_ppdu(). This rx_info structure will be used in the next
patch.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Co-developed-by: Karthikeyan Periyasamy <karthikeyan.periyasamy@oss.qualcomm.com>
Signed-off-by: Karthikeyan Periyasamy <karthikeyan.periyasamy@oss.qualcomm.com>
Signed-off-by: P Praneesh <praneesh.p@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250402182917.2715596-2-praneesh.p@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
ath12k-check is flagging:
drivers/net/wireless/ath/ath12k/dp.c:1656: 'upto' may be misspelled - perhaps 'up to'?
Replace "upto" with "up to" and split the comment line so that it
doesn't exceed 80 columns.
Link: https://patch.msgid.link/20250407-upto-v1-1-23ca65f2ccdf@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
While forming the 802.11 header from the rx descriptor, skb_push() is
performed for the 802.11 header length and then calls
ath12k_dp_rx_desc_get_dot11_hdr(). Since skb_push() moves the skb->data
pointer backwards by the 802.11 header length, the rx descriptor points to
a different memory area than intended, causing invalid information to be
fetched from the rx descriptor.
Also, when IV and ICV are not stripped from the given MSDU, mac80211
performs PN validation for these MSDUs, which requires the crypto header.
Before forming the crypto header from the given rx descriptor, skb_push()
is performed for the crypto header length, which overwrites the memory
pointed to by the rx descriptor, causing invalid information to form the
802.11 header.
Fix these issues by moving all rx descriptor accesses before the skb_push()
operation which ensures the proper 802.11 headers are generated from the
given rx descriptor and removing ath12k_dp_rxdesc_get_mpdu_frame_ctrl()
for filling frame control, as this information is already fetched by
ath12k_dp_rx_desc_get_dot11_hdr().
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Co-developed-by: Karthikeyan Periyasamy <karthikeyan.periyasamy@oss.qualcomm.com>
Signed-off-by: Karthikeyan Periyasamy <karthikeyan.periyasamy@oss.qualcomm.com>
Signed-off-by: P Praneesh <praneesh.p@oss.qualcomm.com>
Link: https://patch.msgid.link/20250402180543.2670947-1-praneesh.p@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The struct sk_buff's control buffer is shared by mac80211's struct
ieee80211_tx_info and ath12k's struct ath12k_skb_cb. When the driver wants
to transmit an skb, it caches all the mac80211-specific information from
struct ieee80211_tx_info, then performs a memset on the control buffer
before writing the ath12k-specific information using struct ath12k_skb_cb.
However, during multicast tx, the key is being filled into the driver data,
which overwrites some crucial members like link_id and flags in struct
ath12k_skb_cb. This causes invalid information retrieval when the driver
accesses these fields during ath12k_dp_tx(). Fix this issue by removing
the key filling logic during MLO multicast tx, as it is not used anywhere
in the tx path.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: 2f50de7256 ("wifi: ath12k: Add support for MLO Multicast handling in driver")
Signed-off-by: P Praneesh <praneesh.p@oss.qualcomm.com>
Link: https://patch.msgid.link/20250402175714.2667270-1-praneesh.p@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently driver enables vdev_id check as part of the bank configuration
in ath12k_dp_tx_get_vdev_bank_config(). This check ensures that the vdev_id
configured in the bank register aligns with the vdev_id in the packet's
address search table within the firmware. If there is a mismatch, the
firmware forwards the packet with the HTT status
HAL_WBM_REL_HTT_TX_COMP_STATUS_VDEVID_MISMATCH. Since driver does not
handle this vdev_id mismatch HTT status, the corresponding buffers are not
freed properly, causing a memory leak. Fix this issue by adding handling to
free the buffers when a vdev_id mismatch HTT status is encountered.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: P Praneesh <praneesh.p@oss.qualcomm.com>
Link: https://patch.msgid.link/20250402174032.2651221-1-praneesh.p@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Before firmware assert, if there is a station interface in the device
which is not associated with an AP, the basic rates are set to zero.
Following this, during firmware recovery, when basic rates are zero,
ath12k driver is sending invalid rate codes, which are negative values,
to firmware. This results in firmware assert.
Fix this by checking if rate codes are valid, before sending them
to the firmware.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Signed-off-by: Roopni Devanathan <quic_rdevanat@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250320112426.1956961-1-quic_rdevanat@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
timer_delete[_sync]() replaces del_timer[_sync](). Convert the whole tree
over and remove the historical wrapper inlines.
Conversion was done with coccinelle plus manual fixups where necessary.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Currently, the existing code lacks functionality to clear the qdesc
array in the REO cache. As a result, any updates in the LUT are not
reflected in the REO cache. To address this issue, add functionality
to clear the qdesc array in the REO cache during a peer TID update.
To do this, set the CLEAR_DESC_ARRAY field of
WCSS_UMAC_REO_R0_QDESC_ADDR_READ and then reset it.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Balamurugan S <quic_bselvara@quicinc.com>
Signed-off-by: Nithyanantham Paramasivam <quic_nithp@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250402152529.1649402-3-quic_nithp@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Instead of storing the REO queue address inside peer entries, REO
hardware module prefers them to be stored in SRAM which could be
directly accessed by REO using peer_ID/TID based lookup table
mechanism.
Fix the enabling of the REO queue lookup table(LUT) feature by
configuring the LUT address information in the REO hardware register
and setting the host service flags.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Nithyanantham Paramasivam <quic_nithp@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250402152529.1649402-2-quic_nithp@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In current WLAN recovery code flow, ath11k_core_halt() only
reinitializes the "arvifs" list head. This will cause the
list node immediately following the list head to become an
invalid list node. Because the prev of that node still points
to the list head "arvifs", but the next of the list head "arvifs"
no longer points to that list node.
When a WLAN recovery occurs during the execution of a vif
removal, and it happens before the spin_lock_bh(&ar->data_lock)
in ath11k_mac_op_remove_interface(), list_del() will detect the
previously mentioned situation, thereby triggering a kernel panic.
The fix is to remove and reinitialize all vif list nodes from the
list head "arvifs" during WLAN halt. The reinitialization is to make
the list nodes valid, ensuring that the list_del() in
ath11k_mac_op_remove_interface() can execute normally.
Call trace:
__list_del_entry_valid_or_report+0xb8/0xd0
ath11k_mac_op_remove_interface+0xb0/0x27c [ath11k]
drv_remove_interface+0x48/0x194 [mac80211]
ieee80211_do_stop+0x6e0/0x844 [mac80211]
ieee80211_stop+0x44/0x17c [mac80211]
__dev_close_many+0xac/0x150
__dev_change_flags+0x194/0x234
dev_change_flags+0x24/0x6c
devinet_ioctl+0x3a0/0x670
inet_ioctl+0x200/0x248
sock_do_ioctl+0x60/0x118
sock_ioctl+0x274/0x35c
__arm64_sys_ioctl+0xac/0xf0
invoke_syscall+0x48/0x114
...
Tested-on: QCA6698AQ hw2.1 PCI WLAN.HSP.1.1-04591-QCAHSPSWPL_V1_V2_SILICONZ_IOE-1
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Stone Zhang <quic_stonez@quicinc.com>
Link: https://patch.msgid.link/20250320053145.3445187-1-quic_stonez@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently ath12k does not send the country code to firmware after device
recovery. As a result the country code will be the default one which
is reported from firmware. Country code is important, so ath12k also
need to restore it to the value which was used before recovery.
This is only needed for platforms which support the current_cc_support
hardware parameter.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250401020840.357-5-quic_kangyang@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The flow of 11d scan is:
1. trigger 11d scan.
2. receive, parse, and update 11d scan result.
3. stop 11d scan.
So need to add handler for WMI_11D_SCAN_START_CMDID and
WMI_11D_SCAN_STOP_CMDID to trigger/stop 11d scan. Add process of WMI
event WMI_11D_NEW_COUNTRY_EVENTID for 11d scan result.
There are two points that need to be noted:
1. The 11d scan priority is 'MEDIUM' in firmware, the hw scan priority
is 'LOW'. When 11d scan is running, hw scan will be canceled.
To avoid this, change the hw scan priority to 'MEDIUM' when 11d scan
is running.
2. Need to add wait_for_completion_timeout() for scan.complete in
ath12k_reg_update_chan_list() because 11d scan will cost more than 5
seconds. Due to another existing wait in ath12k_scan_stop(), there will
be two scan.complete in different threads. Therefore use complete_all()
instead of complete() for scan.complete. complete_all() can work well
when it is only one thread wait for scan.complete.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250401020840.357-4-quic_kangyang@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
When userspace tries to set country code by NL80211_REGDOM_SET_BY_USER
hint(like iw reg set XX), it will pass new country code to ath12k.
Then ath12k will set this new country code to firmware by
WMI_SET_INIT_COUNTRY_CMDID.
For AP based chips(QCN92xx), WMI_SET_INIT_COUNTRY_CMDID is the correct
command. However, for STATION based chips(WCN7850), it need to use
WMI_SET_CURRENT_COUNTRY_CMDID.
Add flag current_cc_support in hardware parameters. It is used to
distinguish AP/STA platform. After that, the firmware will work
normally and the regulatory feature works well for WCN7850.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250401020840.357-3-quic_kangyang@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, WMI_SET_INIT_COUNTRY_CMDID is used to set country code for
WCN7850 and QCN9274.
But WMI_SET_INIT_COUNTRY_CMDID is not the correct command for WCN7850.
Add handler to send WMI_SET_CURRENT_COUNTRY_CMDID to firmware, which
is used for WCN7850 to update country code.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250401020840.357-2-quic_kangyang@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
rx_stats for each arsta is allocated when adding a station.
arsta->rx_stats will be freed when a station is removed.
Redundant allocations are occurring when the same station is added
multiple times. This causes ath12k_mac_station_add() to be called
multiple times, and rx_stats is allocated each time. As a result there
is memory leaks.
Prevent multiple allocations of rx_stats when ath12k_mac_station_add()
is called repeatedly by checking if rx_stats is already allocated
before allocating again. Allocate arsta->rx_stats if arsta->rx_stats
is NULL respectively.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sidhanta Sahu <sidhanta.sahu@oss.qualcomm.com>
Signed-off-by: Muna Sinada <muna.sinada@oss.qualcomm.com>
Reviewed-by: Mahendran P <quic_mahep@quicinc.com>
Link: https://patch.msgid.link/20250326213538.2214194-1-muna.sinada@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
This reverts commit d3e154d777.
With non-WoWLAN suspend support brought back, commit 7f0343b7b8 ("wifi:
ath11k: restore country code during resume") needs to be brought back
as well.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Tested-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Tested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250328-ath11k-bring-hibernation-back-v3-6-23405ae23431@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Now WoWLAN mode is chosen for those machines listed in the quirk table.
This works for suspend (S3) but breaks for hibernation (S4), because
WoWLAN mode requires WLAN power to be sustained, which is not the case
during hibernation. For hibernation, the default mode should be used.
Register a PM notifier with which kernel can notify us of the actual PM
operation: if system is going to suspend, the original PM policy is
honored; while if it is hibernation, overwrite it with default policy.
To summarize: for suspend (S3), WoWLAN mode is chosen for machines listed
in the quirk table, non-WoWLAN mode for others; for hibernation (S4),
non-WoWLAN mode is chosen for all.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Tested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250328-ath11k-bring-hibernation-back-v3-5-23405ae23431@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Previously commit 166a490f59 ("wifi: ath11k: support hibernation") was
reverted due to [1], so currently we only support WoWLAN mode suspend.
This works well in scenarios where WLAN power is sustained during suspend,
however breaks in those where power is cut off.
This change basically brings the reverted commit back, but differs in that
we decide based on the PM policy to choose WoWLAN mode suspend or the
non-WoWLAN mode. As stated in the previous patch for now the PM policy is
determined based on machine models. That said we will choose WoWLAN mode
suspend if we are running on machines listed in ath11k_pm_quirk_table,
otherwise we choose the other one.
[1] https://bugzilla.kernel.org/show_bug.cgi?id=219196
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Tested-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Tested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250328-ath11k-bring-hibernation-back-v3-4-23405ae23431@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Due to [1] we currently put WLAN target into WoWLAN mode regardless of
machine models. In upcoming patches we will support another mode, and
finally which mode is chosen depends on the exact machine model.
To prepare for such change, refactor the actual WoWLAN stuff in
ath11k_core_suspend() into a new helper ath11k_core_suspend_wow(), this
increase the code readability when the new suspend mode is added in
upcoming patches.
Same change applies to ath11k_core_resume();
[1] https://bugzilla.kernel.org/show_bug.cgi?id=219196
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Tested-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Tested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250328-ath11k-bring-hibernation-back-v3-3-23405ae23431@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently ath11k_core_suspend() and ath11k_core_resume() have the same
check before going on. In upcoming patches the check is needed by some
newly added functions as well.
To avoid duplicate code, introduce a new helper
ath11k_core_continue_suspend_resume() which does such check internally.
Callers can decide whether to go on based on its return value.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Tested-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Tested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250328-ath11k-bring-hibernation-back-v3-2-23405ae23431@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
To handle the Lenovo unexpected wakeup issue [1], previously we revert
commit 166a490f59 ("wifi: ath11k: support hibernation"). So currently
WLAN target is put into WoWLAN mode during suspend. This is a temporary
solution as it does not work on machines where WLAN power is cut off.
The thought here is that we do WoWLAN suspend on Lenovo machines while
do non-WoWLAN suspend (which is done in the reverted commit) on other
machines. This requires us to identify Lenovo machines from others.
For that purpose, read board vendor and product name from DMI interface,
match it against all known affected machines. If there is a match, choose
WoWLAN suspend mode, else choose non-WoWLAN mode. Save the mode in ab
for later reference.
[1] https://bugzilla.kernel.org/show_bug.cgi?id=219196
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Tested-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Tested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250328-ath11k-bring-hibernation-back-v3-1-23405ae23431@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Extend the DMA mask to 36 bits to avoid using bounce buffers on machines
without an iommu (under OS control) similar to what was done for ath11k
in commit dbd73acb22 ("wifi: ath11k: enable 36 bit mask for stream
DMA").
This specifically avoids using bounce buffers on Qualcomm Snapdragon X
Elite machines like the Lenovo ThinkPad T14s when running at EL1.
Note that the mask could possibly be extended further but unresolved DMA
issues with 64 GiB X Elite machines currently prevents that from being
tested.
Also note that the driver is limited to 32 bits for coherent
allocations and that there is no need to check for errors when setting
masks larger than 32 bits.
Tested-on: WCN7850 hw2.0 WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Tested-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250321162331.19507-1-johan+linaro@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, the monitor interface is not supported. To support the monitor
interface, configure the monitor vdev state identifier, configure the HTT
filter setup, subscribe the mac80211 NO_VIRTUAL_MONITOR feature, remove
the VIRTUAL_MONITOR handler procedures since align to NO_VIRTUAL_MONITOR
feature and prevent monitor interface to transmit packet. Therefore, add
these procedures to add monitor interface support and enable the monitor
interface support on the QCN9274 platform through the hardware parameter.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250324062518.2752822-11-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, VIRTUAL monitor handling is present. In multi radio model,
VIRTUAL monitor is not suitable since each radio needs a separate VIF and
channel context. Therefore, switch to NO_VIRTUAL_MONITOR feature. Remove
the monitor_conf_enabled flag and mac_op_config() handler as they are not
need for the NO_VIRTUAL_MONITOR feature. In NO_VIRTUAL_MONITOR handling,
each interface creation/deletion triggers the mac_op_add_interface() /
mac_op_remove_interface() callback. Consequently, remove the monitor vdev
create/delete/start/stop from the other vdev type handlers.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250324062518.2752822-10-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, the monitor start procedure use the iteration callback to pick
the last available channel definition in the mac80211 hardware. This
approach is incorrect for the single wiphy model, as it holds multiple
radio/link channel contexts within the same mac80211 hardware. To fix this,
change the iteration callback to pick the specific channel context for the
given radio/link. This approach makes the monitor start procedure
compatible with both multi wiphy and single wiphy models.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Link: https://patch.msgid.link/20250324062518.2752822-9-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, when ath12k_mac_assign_vif_to_vdev() fails, the radio handle
(ar) gets accessed from the link VIF handle (arvif) for debug logging, This
is incorrect. In the fail scenario, radio handle is NULL. Fix the NULL
access, avoid radio handle access by moving to the hardware debug logging
helper function (ath12k_hw_warn).
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: 90570ba461 ("wifi: ath12k: do not return invalid link id for scan link")
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Link: https://patch.msgid.link/20250324062518.2752822-8-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, the packet offset and FCS length are fetched from the MSDU Rx
TLV data, a logic inherited from ath11k. However, for ath12k 802.11be
hardware, the Rx TLV will not be present in the MSDU data. Instead, this
information is constant. Therefore, remove the existing FCS trim and the
packet offset fetch code. Handle the packet offset with the constant in
the merge MSDU procedure.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Tested-by: Nicolas Escande <nico.escande@gmail.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Link: https://patch.msgid.link/20250324062518.2752822-7-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, in the monitor Rx path, status is filled from the RX TLV header
present in the MSDU data. This logic is inherited from ath11k. However, in
the ath12k 802.11be hardware, the Rx TLV header is not present in the MSDU
data. This information is reported under various TLV tags. Therefore, avoid
the existing status filling by accumulating the needed information in the
PPDU information structure and fill the status.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Tested-by: Nicolas Escande <nico.escande@gmail.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Link: https://patch.msgid.link/20250324062518.2752822-6-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, band define and enum are with the word 'G'. Replace it with
more appropriate 'GHZ' for clarity and correctness.
No functional changes. Only compile tested.
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Link: https://patch.msgid.link/20250324062518.2752822-5-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, error bitmap and decap format information are fetched from the
MSDU Rx TLV data. This logic is inherited from ath11k. However, for ath12k
802.11be hardware, the Rx TLV will not be present in the MSDU data.
Instead, this information is reported separately under the MSDU END TLV
tag. Therefore, remove the existing fetch code, handle the MSDU END TLV
tag and fetch the above information to store it in the mon_mpdu data
structure for use in the merge MSDU procedure.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Tested-by: Nicolas Escande <nico.escande@gmail.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Link: https://patch.msgid.link/20250324062518.2752822-4-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, the monitor Rx parser handler is inherited from the ath11k.
However, the ath12k 802.11be hardware does not report the Rx TLV header
in the MSDU data. Instead, the hardware reports those TLVs under the
following TLV tags:
1. Buffer address
2. MPDU start
3. MPDU end
4. MSDU end
Therefore, add support for parsing the above TLVs in the Rx monitor path
and use this information for MSDU buffer and status updates.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Tested-by: Nicolas Escande <nico.escande@gmail.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Link: https://patch.msgid.link/20250324062518.2752822-3-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, the link_valid field is not initialized in the monitor Rx path.
This can result in random values for the link_valid and link_id leads to
undefined behaviour in mac80211. Therefore, initialize the link_valid
field in the monitor Rx path.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Hari Chandrakanthan <quic_haric@quicinc.com>
Tested-by: Nicolas Escande <nico.escande@gmail.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Link: https://patch.msgid.link/20250324062518.2752822-2-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently only PCI devices are supported in Ath12k driver. Refactor
Ath12k module_init and module_exit to include Ath12k AHB support.
Add Ath12k AHB support in Kconfig with dependency on Remoteproc
driver. Ath12k AHB support relies on remoteproc driver for firmware
download, power up/down etc.
Tested-on: IPQ5332 hw1.0 AHB WLAN.WBE.1.3.1-00130-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00210-QCAHKSWPL_SILICONZ-1
Signed-off-by: Balamurugan S <quic_bselvara@quicinc.com>
Co-developed-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Link: https://patch.msgid.link/20250321-ath12k-ahb-v12-13-bb389ed76ae5@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Set the stop bit in SMEM to power down the userPD. Wait for stop-ack IRQ
to indicate power down completion. Release the userPD firmware using its
peripheral ID.
Tested-on: IPQ5332 hw1.0 AHB WLAN.WBE.1.3.1-00130-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sowmiya Sree Elavalagan <quic_ssreeela@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Link: https://patch.msgid.link/20250321-ath12k-ahb-v12-12-bb389ed76ae5@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
UserPD firmware image is loaded and booted by ath12k driver. Get the userPD
memory region from DTS and load the firmware for userPD from pre-defined
path into io-remapped address of this region. Authenticate this image
using pasid which is a peripheral ID. Set the spawn bit to instruct Q6
to spawn userPD thread. Wait for userPD to spawn which is indicated by
spawn interrupt. Ready interrupt is triggered once the userPD is powered
up completely.
Tested-on: IPQ5332 hw1.0 AHB WLAN.WBE.1.3.1-00130-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sowmiya Sree Elavalagan <quic_ssreeela@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Link: https://patch.msgid.link/20250321-ath12k-ahb-v12-11-bb389ed76ae5@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Q6 and ath12k driver communicates using SMEM and IRQs. Spawn interrupt
is triggered once the userPD thread is spawned. Ready interrupts denotes
userPD is completely powered up and ready. Stop-ack is to acknowledge
the ath12k driver that userPD is stopped. Ath12k driver needs to set spawn
bit in SMEM to instruct Q6 to spawn a userPD. Similarly stop bit is
set when userPD needs to be stopped.
Tested-on: IPQ5332 hw1.0 AHB WLAN.WBE.1.3.1-00130-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sowmiya Sree Elavalagan <quic_ssreeela@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Link: https://patch.msgid.link/20250321-ath12k-ahb-v12-10-bb389ed76ae5@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Q6 processor acts as rootPD, other hardware like IPQ5332 which are
attached to Q6 act as userPDs. WCSS driver handles loading and booting
of rootPD, while the ath12k driver boots the userPD.
Get the rproc handle from the DTS entry and boot the rootPD if it
is not already powered on. Register to the rproc notifier to monitor
the rproc state, this allows ath12k driver to know power up/down
sequence of the rootPD. Power up the rootPD and wait for a power-up
notification from the notifier callback before powering up the userPDs.
Tested-on: IPQ5332 hw1.0 AHB WLAN.WBE.1.3.1-00130-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sowmiya Sree Elavalagan <quic_ssreeela@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Co-developed-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Link: https://patch.msgid.link/20250321-ath12k-ahb-v12-9-bb389ed76ae5@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
IPQ5332 firmware supports only fixed QMI firmware memory.
Hence, add support to read reserved fixed memory region from
device-tree and provide the reserved memory segments for
firmware to use during QMI firmware memory request.
Note that the ability to set the fixed memory will be introduced in
a subsequent patch. Currently, the flag remains unset by default,
ensuring that existing chipsets are unaffected.
Tested-on: IPQ5332 hw1.0 AHB WLAN.WBE.1.3.1-00130-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00210-QCAHKSWPL_SILICONZ-1
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Link: https://patch.msgid.link/20250321-ath12k-ahb-v12-7-bb389ed76ae5@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
For IPQ5332 CE register space is moved out of WCSS region and the
space is not contiguous. Hence, add hardware params (ce_ie_addr &
ce_remap) for IPQ5332. These parameters would be used by Ath12k
AHB driver (in subsequent patches) to remap the CE registers to a
new space for accessing them.
Tested-on: IPQ5332 hw1.0 AHB WLAN.WBE.1.3.1-00130-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00210-QCAHKSWPL_SILICONZ-1
Signed-off-by: Balamurugan S <quic_bselvara@quicinc.com>
Co-developed-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Link: https://patch.msgid.link/20250321-ath12k-ahb-v12-6-bb389ed76ae5@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Current ath12k devices, QCN9274 and WCN7850, supports m3.bin firmware
download through ath12k driver. The new ath12k AHB based device
IPQ5332 supports m3 firmware download through remoteproc driver.
Hence, add new parameter (fw.m3_loader) in ath12k_hw_params to avoid
m3 firmware download in IPQ5332.
Tested-on: IPQ5332 hw1.0 AHB WLAN.WBE.1.3.1-00130-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00210-QCAHKSWPL_SILICONZ-1
Signed-off-by: Balamurugan S <quic_bselvara@quicinc.com>
Co-developed-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Link: https://patch.msgid.link/20250321-ath12k-ahb-v12-5-bb389ed76ae5@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Add ath12k_hw_params for new ath12k AHB based WiFi device IPQ5332.
Some hardware parameters like hw_ops, wmi_init & hal_ops are same
between IPQ5332 and QCN9274, hence use these same parameters for
IPQ5332.
Tested-on: IPQ5332 hw1.0 AHB WLAN.WBE.1.3.1-00130-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00210-QCAHKSWPL_SILICONZ-1
Signed-off-by: Balamurugan S <quic_bselvara@quicinc.com>
Co-developed-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Link: https://patch.msgid.link/20250321-ath12k-ahb-v12-4-bb389ed76ae5@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In the current ath12k implementation, the CE addresses
CE_HOST_IE_ADDRESS and CE_HOST_IE_2_ADDRESS are incorrect. These
values were inherited from ath11k, but ath12k does not currently use
them.
However, the Ath12k AHB support relies on these addresses. Therefore,
correct the CE addresses for ath12k.
Tested-on: IPQ5332 hw1.0 AHB WLAN.WBE.1.3.1-00130-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00210-QCAHKSWPL_SILICONZ-1
Signed-off-by: Balamurugan S <quic_bselvara@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Link: https://patch.msgid.link/20250321-ath12k-ahb-v12-2-bb389ed76ae5@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
ieee80211_chanctx_conf struct is not put at the end of ath12k_link_vif.
Note ieee80211_chanctx_conf has flexible array member inside it, causing
below warning with GCC-14:
drivers/net/wireless/ath/ath12k/core.h:298:39: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
Although there is no issue for now since the array is not getting used,
this should be fixed to avoid any potential data corruption issue in the
future.
Remove this struct from ath12k_link_vif, fetch it from ieee80211_bss_conf
instead when needed.
This change only applies to WCN7850, and should has no impact on other
chipsets.
This is an alternative to the solution proposed in [1].
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Reported-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Closes: https://msgid.link/Z8-Snz86Xfwdlyd7@kspp # [1]
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250321-ath12k-dont-put-chanctx-in-arvif-v1-1-c8e93061952b@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
PMF debug log has an open parenthesis that is not needed.
Remove open parenthesis.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Muna Sinada <muna.sinada@oss.qualcomm.com>
Link: https://patch.msgid.link/20250314185605.68454-1-muna.sinada@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
When a character array without a terminating NUL character has a static
initializer, GCC 15's -Wunterminated-string-initialization will only
warn if the array lacks the "nonstring" attribute[1]. Mark the arrays
with __nonstring to and correctly identify the char array as "not a C
string" and thereby eliminate the warning.
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=117178 [1]
Cc: Christian Lamparter <chunkeey@googlemail.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Kees Cook <kees@kernel.org>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
Link: https://patch.msgid.link/20250310222339.work.654-kees@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Driver does not support get_txpower mac ops because of which
cfg80211 returns vif->bss_conf.txpower to user space. bss_conf.txpower
gets its value from ieee80211_channel->max_reg_power. However, the final
txpower is dependent on few other parameters apart from max regulatory
supported power. It is the firmware which knows about all these
parameters and considers the minimum for each packet transmission.
All ath12k firmware reports the final TX power in firmware pdev stats
which falls under fw_stats. add get_txpower mac ops to get the TX power
from firmware leveraging fw_stats and return it accordingly.
While at it, there is a possibility that repeated stats request WMI
commands are queued to FW if mac80211/userspace does get tx power back
to back(in Multiple BSS cases). This could potentially consume the WMI
queue completely. Hence limit this by fetching the power only for every
5 seconds and reusing the value until the refresh timeout or when there
is a change in channel.
Also remove init_completion(&ar->fw_stats_complete) in
ath12k_mac_hw_register() as ath12k_fw_stats_init() takes care of
it for each ar.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Signed-off-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Mahendran P <quic_mahep@quicinc.com>
Link: https://patch.msgid.link/20250306102215.1300522-3-rameshkumar.sundaram@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, firmware stats, comprising pdev, vdev and beacon stats are
part of debugfs. In firmware pdev stats, firmware reports the final
Tx power used to transmit each packet. If driver wants to know the
final Tx power being used at firmware level, it can leverage from
firmware pdev stats.
Move firmware stats out of debugfs context in order to leverage
the final Tx power reported in it even when debugfs is disabled.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Signed-off-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Mahendran P <quic_mahep@quicinc.com>
Link: https://patch.msgid.link/20250306102215.1300522-2-rameshkumar.sundaram@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, for 320 MHz bandwidth, center frequency1 and
center frequency2 are not passed correctly to the firmware.
Set center frequency1 as the center frequency of the
primary 160 MHz channel segment and center frequency2 as the center
frequency of the 320 MHz channel and pass the values
to the firmware.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Suraj P Kizhakkethil <quic_surapk@quicinc.com>
Reviewed-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250304095315.3050325-3-quic_surapk@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, for 160 MHz bandwidth, center frequency1 and
center frequency2 are not passed correctly to the firmware.
Set center frequency1 as the center frequency
of the primary 80 MHz channel segment and center frequency2 as
the center frequency of the 160 MHz channel and pass the values
to the firmware.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Suraj P Kizhakkethil <quic_surapk@quicinc.com>
Reviewed-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250304095315.3050325-2-quic_surapk@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
This development cycle again featured multiple patchsets to ath12k to
support the new 802.11be MLO feature. In addition, there was the usual
set of bug fixes and cleanups.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQ/mtSHzPUi16IfDEksFbugiYzLewUCZ8iK9QAKCRAsFbugiYzL
e9P0AP0T2yU1fl3IRw+q9toRv126vJ7eSKWDZXDU1TppGn/FMQEAiI49Jnhp6WaO
e3nbULnMVF+oOoOTWMJrJ3f6aU5C4AE=
=yTAR
-----END PGP SIGNATURE-----
Merge tag 'ath-next-20250305' of git://git.kernel.org/pub/scm/linux/kernel/git/ath/ath
Jeff Johnson says:
====================
ath.git patches for v6.15
This development cycle again featured multiple patchsets to ath12k to
support the new 802.11be MLO feature. In addition, there was the usual
set of bug fixes and cleanups.
====================
Link: https://lore.kernel.org/linux-wireless/d01b1976-ebe8-48cd-8f49-32bfa00bed7e@oss.qualcomm.com/
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In certain cases, hardware might provide packets with a
length greater than the maximum native Wi-Fi header length.
This can lead to accessing and modifying fields in the header
within the ath12k_dp_rx_h_undecap_nwifi function for
DP_RX_DECAP_TYPE_NATIVE_WIFI decap type and
potentially resulting in invalid data access and memory corruption.
Add a sanity check before processing the SKB to prevent invalid
data access in the undecap native Wi-Fi function for the
DP_RX_DECAP_TYPE_NATIVE_WIFI decap type.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manish Dharanenthiran <quic_mdharane@quicinc.com>
Signed-off-by: Tamizh Chelvam Raja <tamizh.raja@oss.qualcomm.com>
Link: https://patch.msgid.link/20250211090302.4105141-1-tamizh.raja@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently Tx completion for few exception packets are received from
firmware and the tx status updated to mac80211. The tx status values of
HAL_WBM_REL_HTT_TX_COMP_STATUS_DROP and HAL_WBM_REL_HTT_TX_COMP_STATUS_TTL
are considered as tx failure and reported as tx failure to mac80211.
But these failure status is due to internal firmware tx drop and these
packets were not tried to transmit in the air.
In case of mesh this invalid tx status report might trigger mpath broken
issue due to increase in mpath fail average.
So do not report these tx status as tx failure instead free the skb
by calling ieee80211_free_txskb(), and that will be accounted as dropped
frame.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Vinith Kumar R <quic_vinithku@quicinc.com>
Signed-off-by: Tamizh Chelvam Raja <quic_tamizhr@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20241122173432.2064858-1-quic_tamizhr@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Add support for calibration-like properties without 'ath11k' prefix,
while still keeping everything backwards compatible.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patch.msgid.link/20250225-b-wifi-qcom-calibration-variant-v1-5-3b2aa3f89c53@linaro.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Add support for calibration-like properties without 'ath10k' prefix,
while still keeping everything backwards compatible.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patch.msgid.link/20250225-b-wifi-qcom-calibration-variant-v1-4-3b2aa3f89c53@linaro.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Function ath12k_mac_setup_bcn_tmpl_ema() retrieves 'bss_conf'
only to get BSSID index which is an overhead because the
caller ath12k_mac_setup_bcn_tmpl() has already stored this
locally. Pass the index as an input instead.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aloka Dixit <aloka.dixit@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250210182718.408891-6-aloka.dixit@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Add new input parameter to ath12k_mac_setup_bcn_tmpl_ema() for
'tx_arvif' as the caller ath12k_mac_setup_bcn_tmpl() already
stores it locally. Avoid duplicate retrieval.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aloka Dixit <aloka.dixit@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250210182718.408891-5-aloka.dixit@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Create a new function ath12k_mac_get_tx_arvif() to retrieve 'arvif'
for the transmitted interface of the MBSSID set. This clean up will
help modifying the same code path for MLO changes.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aloka Dixit <aloka.dixit@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250210182718.408891-4-aloka.dixit@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Function ath11k_mac_setup_bcn_tmpl() retrieves tx_arvif only for
a sanity check and then calls ath11k_mac_setup_bcn_tmpl_mbssid()
or ath11k_mac_setup_bcn_tmpl_ema() both of which again retrieve
the same pointer. Instead store the pointer and pass it to the
latter two functions. Compile tested only.
Signed-off-by: Aloka Dixit <aloka.dixit@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250210182718.408891-3-aloka.dixit@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Create a new function ath11k_mac_get_tx_arvif() to retrieve 'arvif'
for the transmitted interface of the MBSSID set. This will help
modifying the same code path to reflect mac80211 data structure
changes to support MLO. This also fixes an issue in
ath11k_mac_update_vif_chan() where tx_arvif is not reset to NULL
inside for loop during each iteration. Compile tested only.
Signed-off-by: Aloka Dixit <aloka.dixit@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250210182718.408891-2-aloka.dixit@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
irq_set_affinity_hint() API is deprecated now, so let's use the recommended
equivalent irq_set_affinity_and_hint().
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-05266-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://patch.msgid.link/20250225053447.16824-4-manivannan.sadhasivam@linaro.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
If a shared IRQ is used by the driver due to platform limitation, then the
IRQ affinity hint is set right after the allocation of IRQ vectors in
ath12k_pci_msi_alloc(). This does no harm unless one of the functions
requesting the IRQ fails and attempt to free the IRQ.
This may end up with a warning from the IRQ core that is expecting the
affinity hint to be cleared before freeing the IRQ:
kernel/irq/manage.c:
/* make sure affinity_hint is cleaned up */
if (WARN_ON_ONCE(desc->affinity_hint))
desc->affinity_hint = NULL;
So to fix this issue, clear the IRQ affinity hint before calling
ath12k_pci_free_irq() in the error path. The affinity will be cleared once
again further down the error path due to code organization, but that does
no harm.
Fixes: a3012f206d ("wifi: ath12k: set IRQ affinity to CPU0 in case of one MSI vector")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250225053447.16824-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
If a shared IRQ is used by the driver due to platform limitation, then the
IRQ affinity hint is set right after the allocation of IRQ vectors in
ath11k_pci_alloc_msi(). This does no harm unless one of the functions
requesting the IRQ fails and attempt to free the IRQ. This results in the
below warning:
WARNING: CPU: 7 PID: 349 at kernel/irq/manage.c:1929 free_irq+0x278/0x29c
Call trace:
free_irq+0x278/0x29c
ath11k_pcic_free_irq+0x70/0x10c [ath11k]
ath11k_pci_probe+0x800/0x820 [ath11k_pci]
local_pci_probe+0x40/0xbc
The warning is due to not clearing the affinity hint before freeing the
IRQs.
So to fix this issue, clear the IRQ affinity hint before calling
ath11k_pcic_free_irq() in the error path. The affinity will be cleared once
again further down the error path due to code organization, but that does
no harm.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-05266-QCAHSTSWPLZ_V2_TO_X86-1
Cc: Baochen Qiang <quic_bqiang@quicinc.com>
Fixes: 39564b475a ("wifi: ath11k: fix boot failure with one MSI vector")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250225053447.16824-2-manivannan.sadhasivam@linaro.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, sometimes, the station is unable to identify the configured
AP SSID in its scan results when the AP is not broadcasting its name
publicly and has a hidden SSID.
Currently, channel dwell time for an ath12k station is 30 ms. Sometimes,
station can send broadcast probe request to AP close to the end of dwell
time. In some of these cases, before AP sends a response to the received
probe request, the dwell time on the station side would come to an end.
So, the station will move to scan next channel and will not be able to
acknowledge the unicast probe response.
Resolve this issue by increasing station's channel dwell time to 70 ms,
so that the it remains on the same channel for a longer period. This
would increase the station's chance of receiving probe response from the
AP. The station will then send a response acknowledgment back to the AP,
thus leading to successful scan and BSS discovery.
With an increased dwell time, scan would take longer than it takes now.
But, this fix is an improvement for hidden SSID scan issue.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Ramasamy Kaliappan <quic_rkaliapp@quicinc.com>
Signed-off-by: Roopni Devanathan <quic_rdevanat@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250207060005.153835-1-quic_rdevanat@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
While processing TPC stats received from firmware, there are chances that
the tpc_stats might not be filled and the data is not available. This can
happen under two scenarios. First, when firmware sends a non-zero event
count before event count 0. When this happens, tpc_stats will be checked
for data before memory allocation and the tpc_stats will be unavailable.
Second, when memory allocation failed when event count received is 0 and
the firmware still sends a non-zero event. When this happens, memory will
not be allocated for tpc_stats though event count is 0, so when non-zero
event count is received, tpc_stats will be empty. There are checks to
validate if tpc_stats variable is filled that are used in two subsequent
places, but these are placed after tpc_stats is dereference without
checking if it is NULL or has valid data.
Fix this by removing the mentioned checks and adding a NULL check after
assigning tpc_stats to check if it is valid.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Closes: https://scan7.scan.coverity.com/#/project-view/52668/11354?selectedIssue=1637145
Fixes: f0c3bb78e4 ("wifi: ath12k: Add Support to Parse TPC Event from Firmware")
Signed-off-by: Roopni Devanathan <quic_rdevanat@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250221041250.769491-1-quic_rdevanat@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Commit 3952657848 ("wifi: ath12k: Use mac80211 vif's link_conf instead of
bss_conf") aims at, where applicable, replacing all usage of vif's bss_conf
with link specific bss_conff, but missed one instance in
ath12k_mac_vif_cache_flush(). This results in wrong configurations passed
to ath12k_mac_bss_info_changed() when the link in question is not the default
link.
Change to use the link specific bss_conf to fix this issue.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Fixes: 3952657848 ("wifi: ath12k: Use mac80211 vif's link_conf instead of bss_conf")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20241209024146.3282-1-quic_bqiang@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The current code in dp_rx.h declares the ath12k_dp_rx_h_find_peer() twice.
Fix this by removing one of the redundant declarations of
ath12k_dp_rx_h_find_peer() to ensure that the function is declared only
once.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: P Praneesh <praneesh.p@oss.qualcomm.com>
Link: https://patch.msgid.link/20250219053640.223734-1-praneesh.p@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In case of firmware assert snapshot of firmware memory is essential for
debugging. Add firmware coredump collection support for PCI bus.
Collect RDDM and firmware paging dumps from MHI and pack them in TLV
format and also pack various memory shared during QMI phase in separate
TLVs. Add necessary header and share the dumps to user space using dev
coredump framework. Coredump collection is controlled by
CONFIG_DEV_COREDUMP. Dump collected for a radio is 55 MB approximately.
The changeset is mostly copied from:
https://lore.kernel.org/all/20240325183414.4016663-1-quic_ssreeela@quicinc.com/.
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-04358-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Miaoqing Pan <quic_miaoqing@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20240813013028.2708111-2-quic_miaoqing@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The value of 'ab->hw_params.fixed_mem_region' determines that
only one variable 'vaddr' or 'iaddr' is used in target_mem_chunk.
So use an anonymous union instead, easy to check whether the
memory is set or not.
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-04358-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Miaoqing Pan <quic_miaoqing@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20240813013028.2708111-1-quic_miaoqing@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Add support to request latency stats from firmware through HTT stats
type 25. These stats give information about count of transmitted and
received MAC Protocol Data Units(PDU) and Service Data Units(SDU)
and other latency stats.
Sample output:
-------------
echo 25 > /sys/kernel/debug/ath12k/pci-0000\:06\:00.0/mac0/htt_stats_type
cat /sys/kernel/debug/ath12k/pci-0000\:06\:00.0/mac0/htt_stats
HTT_STATS_LATENCY_CTX_TLV:
duration = 0
tx_msdu_cnt = 0
tx_mpdu_cnt = 0
rx_msdu_cnt = 0
rx_mpdu_cnt = 0
HTT_STATS_LATENCY_PROF_TLV:
Latency name = PROF_SCH_ENQ_TQM_CMDS
count = 0
minimum = 4294967295
maximum = 0
.....
HTT_STATS_LATENCY_CNT_TLV:
prof_enable_cnt = 39
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Dinesh Karthikeyan <quic_dinek@quicinc.com>
Signed-off-by: Roopni Devanathan <quic_rdevanat@quicinc.com>
Link: https://patch.msgid.link/20250204064417.3671928-3-quic_rdevanat@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The single split-phy PCI device can perform multi-link operation (MLO)
within its own radio, and the MLO-supporting firmware also supports MLO
for split-phy PCI devices.
Therefore, enable MLO for the single split-phy PCI device.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aaradhana Sahu <quic_aarasahu@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250207050327.360987-4-quic_aarasahu@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The mlo_capable flag in structure ath12k_hw_group indicate that a device
is capable of operating in multi-link mode. Currently this is enabled
based on single_chip_mlo_support advertised by the firmware within
ath12k_qmi_phy_cap_send().
Since the firmware advertises multi-link operation (MLO) support through
the ATH12K_FW_FEATURE_MLO feature in firmware-2.bin, there is no need to
rely on the QMI phy capability (single_chip_mlo_support). Therefore remove
the dependency on single_chip_mlo_support to set mlo_capable flag.
Below is the impact on single split-phy PCI device with and without this
patch:
Note: This patch does not change the existing behavior of the single
split-phy PCI device.
1. Driver without this patch + firmware with single_chip_mlo_support
as false: MLO is not enabled.
2. Driver without this patch + firmware with single_chip_mlo_support
as true: MLO works fine.
3. Driver with this patch + firmware with single_chip_mlo_support as
false: MLO is not enabled.
4. Driver with this patch + firmware with single_chip_mlo_support as
true: MLO works fine.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aaradhana Sahu <quic_aarasahu@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250207050327.360987-3-quic_aarasahu@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
When multi-link operation(MLO) is enabled through follow-up patches in
the single split-phy device, the firmware expects hardware links
(hw_links) information from the driver.
If driver does not send WMI multi-link setup and ready command to the
firmware during MLO setup for single split-phy device, the firmware will
be unaware of the hw_links component of the multi-link operation. This may
lead to firmware assert during multi-link association.
Therefore, enable WMI setup, ready and teardown commands for single
split-phy PCI device.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aaradhana Sahu <quic_aarasahu@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250207050327.360987-2-quic_aarasahu@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
If ag->mutex has been locked, unlock it before returning. If it has not
been locked, do not unlock it before returning. These bugs have been
detected by the Clang thread-safety analyzer.
Cc: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Cc: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Fixes: ee146e11b4 ("wifi: ath12k: refactor core start based on hardware group")
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250206221317.3845663-1-bvanassche@acm.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
For MLO netdevice, the broadcast frame should be transmitted with the
same sequence number on all the links.
Per IEEE 802.11be-2024 section 10.3.2.14.2 "Transmitter requirements",
An AP MLD shall use SNS11 in Table 10-5 (Transmitter sequence number
spaces) maintained by the MLD to determine the sequence number of a
group addressed data frame that is transmitted by an AP affiliated
with the AP MLD so that the same group addressed Data frame
transmitted over multiple links by the AP MLD uses the same
sequence number for transmission on each link.
Currently the MLO multicast handling is done in the mac80211 layer.
Enable support for handling MLO Multicast in the driver to update the
hardware descriptors in a custom way to handle the multicast frames.
Firmware expects the MLO multicast frames to the submitted to the
hardware with special vdev_id (actual vdev_id + 128) to recognize it as
a host inspected frame to avoid using the reinjected path and it also
uses the multicast global sequence number (GSN) provided by the host
in the HTT metadata to process and transmit it with the same sequence
number.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Balamurugan Mahalingam <quic_bmahalin@quicinc.com>
Reviewed-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250203212647.2694566-3-quic_bmahalin@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Update the HTT_TCL_METADATA version to the latest version (2)
as the bit definitions have changed a little to support more
features. This new version allows the host to submit a packet with
more information to the firmware. Firmware uses this additional
information to do special processing for certain frames.
All the firmware binaries available in upstream/public are compatible with
this HTT version update.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Balamurugan Mahalingam <quic_bmahalin@quicinc.com>
Reviewed-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250203212647.2694566-2-quic_bmahalin@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
ath11k_hal_srng_* should be used with srng->lock to protect srng data.
For ath11k_dp_rx_mon_dest_process() and ath11k_dp_full_mon_process_rx(),
they use ath11k_hal_srng_* for many times but never call srng->lock.
So when running (full) monitor mode, warning will occur:
RIP: 0010:ath11k_hal_srng_dst_peek+0x18/0x30 [ath11k]
Call Trace:
? ath11k_hal_srng_dst_peek+0x18/0x30 [ath11k]
ath11k_dp_rx_process_mon_status+0xc45/0x1190 [ath11k]
? idr_alloc_u32+0x97/0xd0
ath11k_dp_rx_process_mon_rings+0x32a/0x550 [ath11k]
ath11k_dp_service_srng+0x289/0x5a0 [ath11k]
ath11k_pcic_ext_grp_napi_poll+0x30/0xd0 [ath11k]
__napi_poll+0x30/0x1f0
net_rx_action+0x198/0x320
__do_softirq+0xdd/0x319
So add srng->lock for them to avoid such warnings.
Inorder to fetch the srng->lock, should change srng's definition from
'void' to 'struct hal_srng'. And initialize them elsewhere to prevent
one line of code from being too long. This is consistent with other ring
process functions, such as ath11k_dp_process_rx().
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20241219110531.2096-3-quic_kangyang@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
While processing the monitor destination ring, MSDUs are reaped from the
link descriptor based on the corresponding buf_id.
However, sometimes the driver cannot obtain a valid buffer corresponding
to the buf_id received from the hardware. This causes an infinite loop
in the destination processing, resulting in a kernel crash.
kernel log:
ath11k_pci 0000:58:00.0: data msdu_pop: invalid buf_id 309
ath11k_pci 0000:58:00.0: data dp_rx_monitor_link_desc_return failed
ath11k_pci 0000:58:00.0: data msdu_pop: invalid buf_id 309
ath11k_pci 0000:58:00.0: data dp_rx_monitor_link_desc_return failed
Fix this by skipping the problematic buf_id and reaping the next entry,
replacing the break with the next MSDU processing.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20241219110531.2096-2-quic_kangyang@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, the link interface is deleted during channel unassignment, which
does not align with mac80211 link handling. Therefore, add changes to only
perform vdev stop during channel unassignment. The actual vdev deletion
will occur in change_vif_links().
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00130-QCAHKSWPL_SILICONZ-1.97421.5 # Nicolas Escande
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Tested-by: Nicolas Escande <nico.escande@gmail.com>
Link: https://patch.msgid.link/20250204-unlink_link_arvif_from_chanctx-v2-8-764fb5973c1a@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, links in an interface are allocated during channel assignment
via assign_vif_chanctx(). Conversely, links are deleted during channel
unassignment via unassign_vif_chanctx(). However, deleting links during
channel unassignment does not comply with mac80211 link handling.
Therefore, this process should be managed within change_vif_links(). To
maintain symmetry, link addition should also be handled in
change_vif_links().
Hence, add changes to allocate link arvif in change_vif_links(). Creating
the link interface on firmware will still be done during channel
assignment.
And since link will be created but channel might not be assigned, there is
a need now to test is_created flag in ath12k_mac_mlo_get_vdev_args() before
accessing link_conf or else link bring up will fail.
A subsequent change will handle link removal part.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00130-QCAHKSWPL_SILICONZ-1.97421.5 # Nicolas Escande
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Tested-by: Nicolas Escande <nico.escande@gmail.com>
Link: https://patch.msgid.link/20250204-unlink_link_arvif_from_chanctx-v2-7-764fb5973c1a@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
An upcoming change will invoke ath12k_mac_init_arvif(),
ath12k_mac_assign_link_vif(), ath12k_mac_unassign_link_vif(), and
ath12k_mac_remove_link_interface() from a line located above their current
definition. Hence, relocate these functions to above so that these can be
invoked later on.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00130-QCAHKSWPL_SILICONZ-1.97421.5 # Nicolas Escande
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Tested-by: Nicolas Escande <nico.escande@gmail.com>
Link: https://patch.msgid.link/20250204-unlink_link_arvif_from_chanctx-v2-6-764fb5973c1a@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, in ath12k_mac_set_key(), if sta is not present, the address is
retrieved from link_conf's bssid or addr member, depending on the interface
type.
When operating as an ML station and during shutdown, link_conf will not be
available. This can result in the following error:
ath12k_pci 0004:01:00.0: unable to access bss link conf in set key for vif AA:BB:CC:DD:EE:FF link 1
The primary purpose of accessing link_conf is to obtain the address for
finding the peer. However, since arvif is always valid in this call, it can
be used instead.
Add change to use arvif instead of link_conf.
A subsequent change will expose this issue but since tear down will give
error, this is included first.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00130-QCAHKSWPL_SILICONZ-1.97421.5 # Nicolas Escande
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Tested-by: Nicolas Escande <nico.escande@gmail.com>
Link: https://patch.msgid.link/20250204-unlink_link_arvif_from_chanctx-v2-5-764fb5973c1a@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The current logic for initializing arvif is present in both the add
interface operation callback and ath12k_mac_assign_link_vif(). The former
handles deflink initialization, while the latter is responsible for other
links. This redundancy could be avoided by using a common helper function.
Hence, add a new helper ath12k_mac_init_arvif() which initializes a
given arvif.
Since synchronizing rcu is not required after adding a rcu pointer, remove
that now.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00130-QCAHKSWPL_SILICONZ-1.97421.5 # Nicolas Escande
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Tested-by: Nicolas Escande <nico.escande@gmail.com>
Link: https://patch.msgid.link/20250204-unlink_link_arvif_from_chanctx-v2-4-764fb5973c1a@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, vif level settings are done in ath12k_mac_assign_link_vif() as
well as in ath12k_mac_op_add_interface(). Since it is vif level settings,
doing this on per link does not make sense and it contributes to redundant
code. Get rid of this redundant code from ath12k_mac_assign_link_vif().
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00130-QCAHKSWPL_SILICONZ-1.97421.5 # Nicolas Escande
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Tested-by: Nicolas Escande <nico.escande@gmail.com>
Link: https://patch.msgid.link/20250204-unlink_link_arvif_from_chanctx-v2-3-764fb5973c1a@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
There might be instances where ath12k_dbg() is needed, but access to
struct ath12k_base (ab) is not readily available. To address this, add
support to print the debug message using printk() when ab is not present.
To avoid the need to explicitly pass NULL each time, introduce a new macro
ath12k_generic_dbg() which resolves to ath12k_dbg() with ab set to NULL.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00130-QCAHKSWPL_SILICONZ-1.97421.5 # Nicolas Escande
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Tested-by: Nicolas Escande <nico.escande@gmail.com>
Link: https://patch.msgid.link/20250204-unlink_link_arvif_from_chanctx-v2-2-764fb5973c1a@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The current implementation includes a debug mask check both in the macro
expansion and in the function __ath12k_dbg(), which is unnecessary.
Simplify the code by removing the redundant check from the helper function
__ath12k_dbg().
While at this, rename the first argument in macro from ar to ab since the
first argument name in the function __ath12k_dbg() is ab.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00130-QCAHKSWPL_SILICONZ-1.97421.5 # Nicolas Escande
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Tested-by: Nicolas Escande <nico.escande@gmail.com>
Link: https://patch.msgid.link/20250204-unlink_link_arvif_from_chanctx-v2-1-764fb5973c1a@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, peer rate table information involves complex computation for
the rate index to update the rate table. To simplify this process, avoid
the rate index calculation by defining the rate table with bandwidth, GI,
NSS, MCS. Therefore, update the rate information based on the bandwidth,
GI, NSS and MCS information from the TLV data of monitor status Rx path.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Balamurugan Mahalingam <quic_bmahalin@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Link: https://patch.msgid.link/20250206013854.174765-9-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, EHT MCS information is not populated. Therefore, add the EHT
MCS counter array to the peer rate statistics and update the EHT MCS
statistics from the status TLV data in the monitor Rx path. In the future,
this information will be used in the peer extended Rx statistics dump.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Balamurugan Mahalingam <quic_bmahalin@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Link: https://patch.msgid.link/20250206013854.174765-8-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, ampdu id is update with peer id mask which is incorrect.
Therefore, update the ampdu id with PPDU id mask value. Also move
the ampdu_id field inside the user stats since it is a user id based
statistics.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Link: https://patch.msgid.link/20250206013854.174765-7-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, peer id get reported in the PPDU end user TLV tag. But the
monitor status handler is inherited from ath11k, but it was not updated
to incorporate the changes made to ath12k 802.11be hardware architecture.
Therefore, update the peer id from the PPDU end user TLV data to get latest
peer id update, it helps to populate accurate peer information on the
statistics data.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Co-developed-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Link: https://patch.msgid.link/20250206013854.174765-6-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, monitor is not enabled. However, in the future, the monitor
will be enabled. Therefore, add the necessary HAL_PHYRX_OTHER_RECEIVE_INFO
TLV parsing support in the monitor Rx path, which helps to populate the
extended Rx statistics.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Co-developed-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Link: https://patch.msgid.link/20250206013854.174765-5-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, monitor is not enabled. However, in the future, the monitor
will be enabled. Therefore, add necessary HAL_RX_PPDU_START_USER_INFO TLV
parsing support in monitor Rx path, which help to populate the EHT radiotap
data.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Co-developed-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Link: https://patch.msgid.link/20250206013854.174765-4-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, monitor is not enabled. However, in the future, the monitor
will be enabled. Therefore, add the necessary HAL_PHYRX_GENERIC_EHT_SIG
TLV parsing support in monitor Rx path, which help to populate the EHT
radiotap data.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Co-developed-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Link: https://patch.msgid.link/20250206013854.174765-3-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, monitor is not enabled. However, in the future, the monitor
will be enabled. Therefore, add the necessary HAL_PHYRX_GENERIC_U_SIG TLV
parsing support in monitor Rx path, which help to populate the EHT
radiotap data.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Co-developed-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Link: https://patch.msgid.link/20250206013854.174765-2-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
This adds support for reporting to the kernel the average rssi. This is
done the same way as it was done in ath11k. A simple ewma (with the same
parameters) is updated with each rssi update.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Nicolas Escande <nico.escande@gmail.com>
Reviewed-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250201211301.357985-1-nico.escande@gmail.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
We have only one fix for ath12k and one fix for brcmfmac. Also this
will be my last pull request as I'm stepping down as wireless driver
maintainer.
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmemULoRHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZvFigf/fvP7ri+6cyE50Qvau9lQjmrvojQx6Wg4
Jp5kOfXNzyLrEp+SA49UdIEGKak/Speo99ntWvrGrXWSHvW76DzNq5c+XJqffhm6
s+uOcdHlqBRXzD9PuZ0NT75nlb0gBkqGyV6VUW90dwI/lyGNEAwUrbdUO7B8Kmty
KW2hPQP4Zp5Sjm1ZGMKRmwt0qxZBrGKqCq7RqKYldO7PKOhKGfwhpViZxtceo5/2
NdyCVh6LeGP8Kjwo7cMfprNAcLQ2F5+Q9xtjid69TTrW77E9PVK73IGBb+pPwgAd
AzdkNPMX3TwAm/NyAuMhMWXF9VzVzFIfboNgLiAlT2JSYNU7vMtqng==
=54RU
-----END PGP SIGNATURE-----
Merge tag 'wireless-2025-02-07' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
Kalle Valo says:
====================
wireless fixes for v6.14-rc3
We have only one fix for ath12k and one fix for brcmfmac. Also this
will be my last pull request as I'm stepping down as wireless driver
maintainer.
* tag 'wireless-2025-02-07' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless:
MAINTAINERS: wifi: remove Kalle
MAINTAINERS: wifi: ath: remove Kalle
wifi: brcmfmac: use random seed flag for BCM4355 and BCM4364 firmware
wifi: ath12k: fix handling of 6 GHz rules
====================
Link: https://patch.msgid.link/20250207182957.23315C4CED1@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
With previous patch "wifi: ath11k: move update channel list from update
reg worker to reg notifier", ath11k_reg_update_chan_list() will be
called during reg_process_self_managed_hint().
reg_process_self_managed_hint() will hold rtnl_lock all the time.
But ath11k_reg_update_chan_list() may increase the occupation time of
rtnl_lock, because when wait flag is set, wait_for_completion_timeout()
will be called during 11d/hw scan.
Should minimize the occupation time of rtnl_lock as much as possible
to avoid interfering with rest of the system. So move the update channel
list operation to a new worker, so that wait_for_completion_timeout()
won't be called and will not increase the occupation time of rtnl_lock.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Co-developed-by: Kang Yang <quic_kangyang@quicinc.com>
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Reviewed-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://patch.msgid.link/20250117061737.1921-3-quic_kangyang@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently when ath11k gets a new channel list, it will be processed
according to the following steps:
1. update new channel list to cfg80211 and queue reg_work.
2. cfg80211 handles new channel list during reg_work.
3. update cfg80211's handled channel list to firmware by
ath11k_reg_update_chan_list().
But ath11k will immediately execute step 3 after reg_work is just
queued. Since step 2 is asynchronous, cfg80211 may not have completed
handling the new channel list, which may leading to an out-of-bounds
write error:
BUG: KASAN: slab-out-of-bounds in ath11k_reg_update_chan_list
Call Trace:
ath11k_reg_update_chan_list+0xbfe/0xfe0 [ath11k]
kfree+0x109/0x3a0
ath11k_regd_update+0x1cf/0x350 [ath11k]
ath11k_regd_update_work+0x14/0x20 [ath11k]
process_one_work+0xe35/0x14c0
Should ensure step 2 is completely done before executing step 3. Thus
Wen raised patch[1]. When flag NL80211_REGDOM_SET_BY_DRIVER is set,
cfg80211 will notify ath11k after step 2 is done.
So enable the flag NL80211_REGDOM_SET_BY_DRIVER then cfg80211 will
notify ath11k after step 2 is done. At this time, there will be no
KASAN bug during the execution of the step 3.
[1] https://patchwork.kernel.org/project/linux-wireless/patch/20230201065313.27203-1-quic_wgong@quicinc.com/
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Fixes: f45cb6b29c ("wifi: ath11k: avoid deadlock during regulatory update in ath11k_regd_update()")
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Reviewed-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://patch.msgid.link/20250117061737.1921-2-quic_kangyang@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Host receives four Transmit Power Control(TPC) events from firmware on
sending TPC request. Fixed param TLV is present as part of all event to
indicate the event count and end of event. TPC config parameters along
with regulatory power array comes as first event. Rates array comes as
second and third event as it cannot be packed in single event.
Conformance Test Limit (CTL) power array comes as the fourth event.
Firmware packs different sets of array params which includes array
length and type inside master TLV as different subtlvs. And the actual
content of array is packed one after the other inside a separate TLV as
single buffer.
Parse various events and save it in local structures. Create tpc_stats
file using debugfs to store these local structures. Create function to
handle TPC stats read to relay the information to the user.
Command usage:
cat > /sys/kernel/debug/ath12k/pci-0000\:06\:00.0/mac0/tpc_stats
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00214-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sowmiya Sree Elavalagan <quic_ssreeela@quicinc.com>
Co-developed-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Signed-off-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Co-developed-by: Roopni Devanathan <quic_rdevanat@quicinc.com>
Signed-off-by: Roopni Devanathan <quic_rdevanat@quicinc.com>
Reviewed-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250130061104.962124-2-quic_rdevanat@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Current code in ath11k_mac_set_txbf_conf overrides nsts, which is
incorrect as it confuses nss and nsts. nss is Number of Spatial
Streams，nsts is Number of Space-Time Streams.
As mentioned in Fixes: 55b5ee3357, the nss used when acting as a
beamformee in VHT mode should be reported by the firmware and should not
be greater than the number of receiving antennas - 1. The num_rx_chains
related nss rather than nsts.
If STBC is enabled, nsts is greater than nss. About nss are mapped to
nsts, refer to IEEE Std 802.11-2020: 19.3.11.9.2 Space-time block coding
(STBC), Table 19-18—Constellation mapper output to spatial mapper input
for STBC.
Remove wrong overriding for nsts of VHT Beamformee STS Capability,
acting DL MU-MIMO in VHT mode is working properly.
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-04479-QCAHSPSWPL_V1_V2_SILICONZ_IOE-1
Fixes: 55b5ee3357 ("wifi: ath11k: fix number of VHT beamformee spatial streams")
Signed-off-by: Yu Zhang (Yuriy) <quic_yuzha@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250124075953.2282354-1-quic_yuzha@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The current code does not have the MU EDCA feature, so it cannot support
the use of EDCA by STA in specific UL MU HE TB PPDU transmissions. Refer
to IEEE Std 802.11ax-2021 "9.4.2.251 MU EDCA Parameter Set element",
"26.2.7 EDCA operation using MU EDCA parameters".
Add ath11k_mac_op_conf_tx_mu_edca() to construct the MU EDCA parameters
received from mac80211 into WMI WMM parameters，and send to the firmware
according to the different WMM type flags.
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-04523-QCAHSPSWPL_V1_V2_SILICONZ_IOE-1
Signed-off-by: Yu Zhang (Yuriy) <quic_yuzha@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250124061343.2263467-1-quic_yuzha@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, ath12k does not support reading variant from ACPI board data
filename extension for downloading board data file.
To address this issue, obtain the string of the ACPI data filename
extension and use it as part of the string to search for the board data
file from board-2.bin.
This patch will not affect QCN9274, because only WCN7850 supports ACPI.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20250113074810.29729-5-quic_lingbok@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, the timing for accessing the ACPI table is inappropriate.
Due to special ACPI requirements, the ACPI table must be obtained before
downloading the board data file. Therefore, adjust the timing for accessing
the ACPI table accordingly.
This patch will not affect QCN9274, because only WCN7850 supports ACPI.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20250113074810.29729-4-quic_lingbok@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, ath12k does not support enable or disable specific features by
ACPI bitflag.
To address this issue, obtain the ACPI bitflag value and use it to
selectively enable or disable specific features.
This patch will not affect QCN9274, because only WCN7850 supports ACPI.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20250113074810.29729-3-quic_lingbok@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, ath12k does not support obtaining the buffer type ACPI function
bitmap.
To solve this issue, change the code to support obtaining the buffer type
ACPI function bitmap.
This patch will not affect QCN9274, because only WCN7850 supports ACPI.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20250113074810.29729-2-quic_lingbok@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently ath12k_mac_ieee80211_sta_bw_to_wmi() handles the bandwidth from
sta's deflink member. This works only for non-ML station. Now that MLO
support is there, extend this function to use link sta instead of deflink.
Additionally, in ath12k_mac_handle_link_sta_state(), the link sta structure
is not accessible, making it difficult to fetch the bandwidth there.
However, ath12k_mac_station_assoc() does reference the link sta structure.
Therefore, move the initial assignment of the arsta bandwidth member to
ath12k_mac_station_assoc().
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Acked-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Link: https://patch.msgid.link/20250110-fix_link_sta_bandwidth_update-v1-2-61b6f3ef2ea3@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
An upcoming change will invoke ath12k_mac_ieee80211_sta_bw_to_wmi() from a
line located above its current definition. Hence, relocate it to above
so that it can be invoked later on.
No functionality changes. Compile tested only.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Acked-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Link: https://patch.msgid.link/20250110-fix_link_sta_bandwidth_update-v1-1-61b6f3ef2ea3@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In case of MHI error a reset work will be queued which will try
napi_disable() after napi_synchronize().
As the napi will be only enabled after qmi_firmware_ready event,
trying napi_synchronize() before napi_enable() will result in
indefinite sleep in case of a firmware crash in QMI init sequence.
To avoid this, introduce napi_enabled flag to check if napi is enabled
or not before calling napi_synchronize().
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Avula Sri Charan <quic_asrichar@quicinc.com>
Signed-off-by: Tamizh Chelvam Raja <quic_tamizhr@quicinc.com>
Reviewed-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250124090058.3194299-1-quic_tamizhr@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, when the driver receives a channel switch count WMI event from
the firmware with a count greater than 1, it calls
ieee80211_beacon_update_cntdwn(). If the beacon transmission fails, the
event will be received again with the previous count value. In this
scenario, the host decrements the mac80211 counter again, causing it to
move ahead of the firmware counter. Ultimately, when the firmware count
reaches 1, the mac80211 counter will reach zero, triggering a
WARN_ON_ONCE(). Therefore, there is a need to check the count value in the
event.
Hence to fix this, maintain the current ongoing counter in arvif. If the
count in the event does not match the expected value, silently discard the
event.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://patch.msgid.link/20250124-ath12k_mlo_csa-v2-4-420c42fcfecf@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
At present, the driver configures the firmware to send the Channel Switch
(CS) count event only when the count reaches zero during a Channel Switch
Announcement (CSA). For frames managed by the upper layer, where the driver
does not update the counter, the CS count in these frames remains unchanged
throughout the entire CSA period. This is because the upper layer is not
aware of the latest ongoing count. Indicating same count value throughout
the CSA time is wrong and could lead to connection instabilities.
Fix this by configuring firmware to send CS count event for every count and
then accordingly decrementing the count in mac80211.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://patch.msgid.link/20250124-ath12k_mlo_csa-v2-3-420c42fcfecf@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The driver is informed of the counter offsets in the beacon during CSA
through the ieee80211_mutable_offsets structure. According to the
documentation for the cntdwn_counter_offs member, "This array can contain
zero values which should be ignored." However, the current implementation
uses these values unconditionally, without checking for zeros.
Whenever CSA is active, these offsets are guaranteed to be set. Therefore,
add a check for CSA active status before setting the CSA switch count
offsets. This ensures that the offsets are only set when CSA is active,
preventing incorrect configurations.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://patch.msgid.link/20250124-ath12k_mlo_csa-v2-2-420c42fcfecf@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The current code has ath12k_wmi_bcn_tmpl() accepting separate ar and
vdev_id parameters. However, ath12k_link_vif structure can be used to
derive both of these.
Hence, simplify the function signature.
Later change needs arvif pointer access within the function hence it is
better if arvif is directly passed now.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://patch.msgid.link/20250124-ath12k_mlo_csa-v2-1-420c42fcfecf@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently in ath12k_mac_op_sta_statistics() there is the following
logic:
if (!arsta->txrate.legacy && !arsta->txrate.nss)
return;
Because ath12k_sta_statistics is used to report many info to iw wlan0 link,
if it return for empty legacy and nss of arsta->txrate, then the other
stats after it will not be set.
To address this issue remove the return and instead invert the logic to set
the txrate logic if (arsta->txrate.legacy || arsta->txrate.nss).
The same was done also in both ath10k with commit 1cd6ba8ae3 ("ath10k:
remove return for NL80211_STA_INFO_TX_BITRATE") and ath11k as well with
commit 1d795645e1 ("ath11k: remove return for empty tx bitrate in
mac_op_sta_statistics").
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Reviewed-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/38c2a7c4f7eaf57b9306bb95a9e6c42b7d987e05.1738169458.git.repk@triplefau.lt
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Since inception there is an obvious typo laying around in
ath12k_hal_tx_cmd_ext_desc_setup(). Instead of initializing + adding
flags to tcl_ext_cmd->info1, we initialize + override. This will be needed
in the future to make broadcast frames work with ethernet encapsulation.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Nicolas Escande <nico.escande@gmail.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250127071306.1454699-1-nico.escande@gmail.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Commit b205ce4c26 ("ath11k: support avg signal in station dump") added an
extra assignment of arsta->rssi_comb in ath11k_dp_rx_update_peer_stats()
when it added the average rssi support. So let's keep only one by removing
the legacy assignment so the two statements about rssi stay next to each
other. Compile tested only.
Signed-off-by: Nicolas Escande <nico.escande@gmail.com>
Reviewed-by: Vasanthakumar Thiagarajan <quic_vthiagar@quicinc.com>
Link: https://patch.msgid.link/20250117181953.3375273-1-nico.escande@gmail.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In 'ath_cmn_process_fft()', it doesn't make too much sense to
add zero bytes in attempt to improve randomness. So swap calls
to 'memset()' and 'add_device_randomness()' to feed the pool
with actual FFT results rather than zeroes. Compile tested only.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Fixes: 2aa56cca35 ("ath9k: Mix the received FFT bins to the random pool")
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://patch.msgid.link/20250123141058.1696502-1-dmantipov@yandex.ru
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
When using nvmem, ath9k could potentially be loaded before nvmem, which
loads after mtd. This is an issue if DT contains an nvmem mac address.
If nvmem is not ready in time for ath9k, -EPROBE_DEFER is returned. Pass
it to _probe so that ath9k can properly grab a potentially present MAC
address.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://patch.msgid.link/20241105222326.194417-1-rosenp@gmail.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, ath12k_core_fetch_regdb() finds regdb.bin file through
board id's but in board-2.bin file regdb.bin file is present with
default board id because of which regdb.bin is not fetched.
Add support to fetch regdb.bin file from board-2.bin through
default board id.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aaradhana Sahu <quic_aarasahu@quicinc.com>
Reviewed-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://patch.msgid.link/20250116032835.118397-1-quic_aarasahu@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Here is the big set of driver core and debugfs updates for 6.14-rc1.
It's coming late in the merge cycle as there are a number of merge
conflicts with your tree now, and I wanted to make sure they were
working properly. To resolve them, look in linux-next, and I will send
the "fixup" patch as a response to the pull request.
Included in here is a bunch of driver core, PCI, OF, and platform rust
bindings (all acked by the different subsystem maintainers), hence the
merge conflict with the rust tree, and some driver core api updates to
mark things as const, which will also require some fixups due to new
stuff coming in through other trees in this merge window.
There are also a bunch of debugfs updates from Al, and there is at least
one user that does have a regression with these, but Al is working on
tracking down the fix for it. In my use (and everyone else's linux-next
use), it does not seem like a big issue at the moment.
Here's a short list of the things in here:
- driver core bindings for PCI, platform, OF, and some i/o functions.
We are almost at the "write a real driver in rust" stage now,
depending on what you want to do.
- misc device rust bindings and a sample driver to show how to use
them
- debugfs cleanups in the fs as well as the users of the fs api for
places where drivers got it wrong or were unnecessarily doing things
in complex ways.
- driver core const work, making more of the api take const * for
different parameters to make the rust bindings easier overall.
- other small fixes and updates
All of these have been in linux-next with all of the aforementioned
merge conflicts, and the one debugfs issue, which looks to be resolved
"soon".
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZ5koPA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymFHACfT5acDKf2Bov2Lc/5u3vBW/R6ChsAnj+LmgVI
hcDSPodj4szR40RRnzBd
=u5Ey
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core and debugfs updates from Greg KH:
"Here is the big set of driver core and debugfs updates for 6.14-rc1.
Included in here is a bunch of driver core, PCI, OF, and platform rust
bindings (all acked by the different subsystem maintainers), hence the
merge conflict with the rust tree, and some driver core api updates to
mark things as const, which will also require some fixups due to new
stuff coming in through other trees in this merge window.
There are also a bunch of debugfs updates from Al, and there is at
least one user that does have a regression with these, but Al is
working on tracking down the fix for it. In my use (and everyone
else's linux-next use), it does not seem like a big issue at the
moment.
Here's a short list of the things in here:
- driver core rust bindings for PCI, platform, OF, and some i/o
functions.
We are almost at the "write a real driver in rust" stage now,
depending on what you want to do.
- misc device rust bindings and a sample driver to show how to use
them
- debugfs cleanups in the fs as well as the users of the fs api for
places where drivers got it wrong or were unnecessarily doing
things in complex ways.
- driver core const work, making more of the api take const * for
different parameters to make the rust bindings easier overall.
- other small fixes and updates
All of these have been in linux-next with all of the aforementioned
merge conflicts, and the one debugfs issue, which looks to be resolved
"soon""
* tag 'driver-core-6.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (95 commits)
rust: device: Use as_char_ptr() to avoid explicit cast
rust: device: Replace CString with CStr in property_present()
devcoredump: Constify 'struct bin_attribute'
devcoredump: Define 'struct bin_attribute' through macro
rust: device: Add property_present()
saner replacement for debugfs_rename()
orangefs-debugfs: don't mess with ->d_name
octeontx2: don't mess with ->d_parent or ->d_parent->d_name
arm_scmi: don't mess with ->d_parent->d_name
slub: don't mess with ->d_name
sof-client-ipc-flood-test: don't mess with ->d_name
qat: don't mess with ->d_name
xhci: don't mess with ->d_iname
mtu3: don't mess wiht ->d_iname
greybus/camera - stop messing with ->d_iname
mediatek: stop messing with ->d_iname
netdevsim: don't embed file_operations into your structs
b43legacy: make use of debugfs_get_aux()
b43: stop embedding struct file_operations into their objects
carl9170: stop embedding file_operations into their objects
...
Fix an issue in the ath12k driver where 6 GHz operation no longer
works with new firmware.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQ/mtSHzPUi16IfDEksFbugiYzLewUCZ5PnQgAKCRAsFbugiYzL
e7fqAQD+c2nHTsGZAIhqYeXNwTYYjh26bHFuhWNJbEIjKE5D5wD+N/P72NsDzynh
bq6NFrsA9noQPnWtPX9fvoWEzPyK2gs=
=IqRH
-----END PGP SIGNATURE-----
Merge tag 'ath-current-20250124' of git://git.kernel.org/pub/scm/linux/kernel/git/ath/ath
ath.git patch for v6.14-rc
Fix an issue in the ath12k driver where 6 GHz operation no longer
works with new firmware.
this pull are:
- "lib min_heap: Improve min_heap safety, testing, and documentation"
from Kuan-Wei Chiu provides various tightenings to the min_heap library
code.
- "xarray: extract __xa_cmpxchg_raw" from Tamir Duberstein preforms some
cleanup and Rust preparation in the xarray library code.
- "Update reference to include/asm-<arch>" from Geert Uytterhoeven fixes
pathnames in some code comments.
- "Converge on using secs_to_jiffies()" from Easwar Hariharan uses the
new secs_to_jiffies() in various places where that is appropriate.
- "ocfs2, dlmfs: convert to the new mount API" from Eric Sandeen
switches two filesystems to the new mount API.
- "Convert ocfs2 to use folios" from Matthew Wilcox does that.
- "Remove get_task_comm() and print task comm directly" from Yafang Shao
removes now-unneeded calls to get_task_comm() in various places.
- "squashfs: reduce memory usage and update docs" from Phillip Lougher
implements some memory savings in squashfs and performs some
maintainability work.
- "lib: clarify comparison function requirements" from Kuan-Wei Chiu
tightens the sort code's behaviour and adds some maintenance work.
- "nilfs2: protect busy buffer heads from being force-cleared" from
Ryusuke Konishi fixes an issues in nlifs when the fs is presented with a
corrupted image.
- "nilfs2: fix kernel-doc comments for function return values" from
Ryusuke Konishi fixes some nilfs kerneldoc.
- "nilfs2: fix issues with rename operations" from Ryusuke Konishi
addresses some nilfs BUG_ONs which syzbot was able to trigger.
- "minmax.h: Cleanups and minor optimisations" from David Laight
does some maintenance work on the min/max library code.
- "Fixes and cleanups to xarray" from Kemeng Shi does maintenance work
on the xarray library code.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCZ5SP5QAKCRDdBJ7gKXxA
jqN7AQChvwXGG43n4d5SDiA/rH7ddvowQcDqhC9cAMJ1ReR7qwEA8/LIWDE4PdMX
mJnaZ1/ibpEpearrChCViApQtcyEGQI=
=ti4E
-----END PGP SIGNATURE-----
Merge tag 'mm-nonmm-stable-2025-01-24-23-16' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull non-MM updates from Andrew Morton:
"Mainly individually changelogged singleton patches. The patch series
in this pull are:
- "lib min_heap: Improve min_heap safety, testing, and documentation"
from Kuan-Wei Chiu provides various tightenings to the min_heap
library code
- "xarray: extract __xa_cmpxchg_raw" from Tamir Duberstein preforms
some cleanup and Rust preparation in the xarray library code
- "Update reference to include/asm-<arch>" from Geert Uytterhoeven
fixes pathnames in some code comments
- "Converge on using secs_to_jiffies()" from Easwar Hariharan uses
the new secs_to_jiffies() in various places where that is
appropriate
- "ocfs2, dlmfs: convert to the new mount API" from Eric Sandeen
switches two filesystems to the new mount API
- "Convert ocfs2 to use folios" from Matthew Wilcox does that
- "Remove get_task_comm() and print task comm directly" from Yafang
Shao removes now-unneeded calls to get_task_comm() in various
places
- "squashfs: reduce memory usage and update docs" from Phillip
Lougher implements some memory savings in squashfs and performs
some maintainability work
- "lib: clarify comparison function requirements" from Kuan-Wei Chiu
tightens the sort code's behaviour and adds some maintenance work
- "nilfs2: protect busy buffer heads from being force-cleared" from
Ryusuke Konishi fixes an issues in nlifs when the fs is presented
with a corrupted image
- "nilfs2: fix kernel-doc comments for function return values" from
Ryusuke Konishi fixes some nilfs kerneldoc
- "nilfs2: fix issues with rename operations" from Ryusuke Konishi
addresses some nilfs BUG_ONs which syzbot was able to trigger
- "minmax.h: Cleanups and minor optimisations" from David Laight does
some maintenance work on the min/max library code
- "Fixes and cleanups to xarray" from Kemeng Shi does maintenance
work on the xarray library code"
* tag 'mm-nonmm-stable-2025-01-24-23-16' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (131 commits)
ocfs2: use str_yes_no() and str_no_yes() helper functions
include/linux/lz4.h: add some missing macros
Xarray: use xa_mark_t in xas_squash_marks() to keep code consistent
Xarray: remove repeat check in xas_squash_marks()
Xarray: distinguish large entries correctly in xas_split_alloc()
Xarray: move forward index correctly in xas_pause()
Xarray: do not return sibling entries from xas_find_marked()
ipc/util.c: complete the kernel-doc function descriptions
gcov: clang: use correct function param names
latencytop: use correct kernel-doc format for func params
minmax.h: remove some #defines that are only expanded once
minmax.h: simplify the variants of clamp()
minmax.h: move all the clamp() definitions after the min/max() ones
minmax.h: use BUILD_BUG_ON_MSG() for the lo < hi test in clamp()
minmax.h: reduce the #define expansion of min(), max() and clamp()
minmax.h: update some comments
minmax.h: add whitespace around operators and after commas
nilfs2: do not update mtime of renamed directory that is not moved
nilfs2: handle errors that nilfs_prepare_chunk() may return
CREDITS: fix spelling mistake
...
QCN9274's monitor related rings are initialized properly. Hence enabling
the corresponding ring mask in the hardware params.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Link: https://patch.msgid.link/20241223060132.3506372-15-quic_ppranees@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
During monitor destination ring back-pressure, hardware failed to send
HAL_RX_PPDU_END_STATUS_DONE TLV. But driver uses this TLV as a delimiter
to complete one PPDU worth of data parsing. This causes driver to overwrite
the existing PPDU information with the new PPDU information.
Fix it by recording the end reason which is provided under each buffer's
descriptor in skb->cb and uses it while parsing TLV tags to mark the PPDU
end delimiter.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Link: https://patch.msgid.link/20241223060132.3506372-14-quic_ppranees@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Driver uses monitor destination rings for extended statistics mode and
standalone monitor mode. In extended statistics mode, TLVs are parsed from
the buffer received from the monitor destination ring and assigned to the
ppdu_info structure to update per-packet statistics. In standalone monitor
mode, along with per-packet statistics, the packet data (payload) is
captured, and the driver updates per MSDU to mac80211.
When the AP interface is enabled, only extended statistics mode is
activated. As part of enabling monitor rings for collecting statistics,
the driver subscribes to HAL_RX_MPDU_START TLV in the filter
configuration. This TLV is received from the monitor destination ring, and
kzalloc for the mon_mpdu object occurs, which is not freed, leading to a
memory leak. The kzalloc for the mon_mpdu object is only required while
enabling the standalone monitor interface. This causes a memory leak while
enabling extended statistics mode in the driver.
Fix this memory leak by removing the kzalloc for the mon_mpdu object in
the HAL_RX_MPDU_START TLV handling. Additionally, remove the standalone
monitor mode handlings in the HAL_MON_BUF_ADDR and HAL_RX_MSDU_END TLVs.
These TLV tags will be handled properly when enabling standalone monitor
mode in the future.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Link: https://patch.msgid.link/20241223060132.3506372-13-quic_ppranees@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Each PPDU contains numerous TLV tags. HAL_RX_PPDU_START marks the start
of the PPDU, and HAL_RX_PPDU_END_STATUS_DONE marks the end. From the
monitor destination rings, the driver retrieves skb containing these
TLV tags and their corresponding data. Sometimes, one PPDU’s information
spreads across multiple skbs. The current parsing logic uses memset on
struct hal_rx_mon_ppdu_info after parsing each skb, leading to information
loss if a PPDU spans multiple skbs. Fix this by setting the
ppdu_continuation flag when the driver fails to get
HAL_RX_PPDU_END_STATUS_DONE, and do memset on struct
hal_rx_mon_ppdu_info only when the ppdu_continuation flag is not set.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Link: https://patch.msgid.link/20241223060132.3506372-12-quic_ppranees@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In the current implementation, when PPDU spans multiple ring descriptors,
leading to inefficient use of the NAPI budget. The budget counter is
decremented for each ring descriptor, causing rapid depletion of the
budget even though the processing of a single PPDU might not be complete.
To address this issue, modify the code to decrement the budget counter
only when the driver receives HAL_MON_END_OF_PPDU as the end reason. This
change ensures that the budget is decremented only once per PPDU,
resulting in more efficient utilization of the NAPI budget and better
handling of monitor destination ring.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Link: https://patch.msgid.link/20241223060132.3506372-11-quic_ppranees@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, the monitor destination ring's descriptor includes a 2-bit
field for the end reason. Out of all the end reason values, hardware uses
HAL_MON_FLUSH_DETECTED and HAL_MON_PPDU_TRUNCATED to indicate buffers that
should not be processed due to system level errors. Driver should not
process entries with these end reasons, as they contain junk values.
However, the current code lacks end reason-specific checks for the monitor
destination ring, leading to the processing of invalid buffers.
Fix this by adding checks for these two end reasons during the reaping
phase. Free the skb if either HAL_MON_FLUSH_DETECTED or
HAL_MON_PPDU_TRUNCATED is detected, preventing the driver from processing
invalid entries.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Link: https://patch.msgid.link/20241223060132.3506372-10-quic_ppranees@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
When monitor block in Hardware experiences internal backpressure, a ring
entry with the EMPTY_DESC reason is received in the monitor destination
ring descriptor. The cookie field for this corresponding entry is invalid.
Currently driver attempts to process this cookie resulting in invalid
buf_id warning logs flooding the console. To fix this, skip processing the
destination descriptor when the EMPTY_DESCRIPTOR bit is set to true in ring
descriptor, thereby avoiding the processing of junk cookies.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Link: https://patch.msgid.link/20241223060132.3506372-9-quic_ppranees@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
End offset for the monitor destination ring descriptor is defined as
16 bits, while the firmware definition specifies only 12 bits.
The remaining bits (bit 12 to bit 15) are reserved and may contain
junk values, leading to invalid information retrieval. Fix this issue
by updating the correct genmask values.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Link: https://patch.msgid.link/20241223060132.3506372-8-quic_ppranees@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, ath12k_dp_mon_srng_process uses ath12k_hal_srng_src_get_next_entry
to fetch the next entry from the destination ring. This is incorrect because
ath12k_hal_srng_src_get_next_entry is intended for source rings, not destination
rings. This leads to invalid entry fetches, causing potential data corruption or
crashes due to accessing incorrect memory locations. This happens because the
source ring and destination ring have different handling mechanisms and using
the wrong function results in incorrect pointer arithmetic and ring management.
To fix this issue, replace the call to ath12k_hal_srng_src_get_next_entry with
ath12k_hal_srng_dst_get_next_entry in ath12k_dp_mon_srng_process. This ensures
that the correct function is used for fetching entries from the destination
ring, preventing invalid memory accesses.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Link: https://patch.msgid.link/20241223060132.3506372-7-quic_ppranees@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, monitor ring reaping and processing occur in the same loop,
which requires holding ring locks until skb processing is complete.
However, only the ring reaping part requires the ring lock; the skb
processing part does not need it. This approach is problematic because it
unnecessarily extends the duration for which the ring locks are held,
leading to increased contention and potential backpressure issues.
Fix it by holding ring locks only during the reaping phase, as skb
processing does not require them. First, reap the monitor destination ring
with the ring lock and queue the skbs into an skb list. Then, process the
skbs in this list in a separate loop without holding the ring lock.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Link: https://patch.msgid.link/20241223060132.3506372-6-quic_ppranees@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The current implementation processes the monitor destination ring using
two separate functions, ath12k_dp_mon_srng_process() for standalone
monitor mode and ath12k_dp_mon_rx_process_stats() for statistics.
However, both functions contain same code which performs monitor ring
reaping and skb data processing. To eliminate redundancy, remove the
duplicate code and use a single function to handle both the cases.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Link: https://patch.msgid.link/20241223060132.3506372-5-quic_ppranees@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
ath12k_mac_op_configure_filter() gets called multiple times during
interface bringup. Applying filter configuration from this function leads
to writing same filter configurations multiple times.
Resolve this issue by relocating the filter configuration to
ath12k_mac_config_mon_status_default(), which is invoked by both
ath12k_mac_op_start() and ath12k_mac_op_stop(). Additionally, set the
rxmon_disable flag to true when called from ath12k_mac_op_stop() to
disable the monitor destination ring.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Link: https://patch.msgid.link/20241223060132.3506372-4-quic_ppranees@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Add provision to configure monitor filter for the destination
ring. These filters are used for requesting statistics or monitor mode
through the monitor destination ring.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Link: https://patch.msgid.link/20241223060132.3506372-3-quic_ppranees@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Add source buffer ring and destination buffer ring ID for monitor rings.
These IDs are used for ring configuration during initial ring setup.
Since monitor rings are enabled based on the rxdma1_enable flag, enable it
in the hardware param for the QCN9274 version 2 hardware and increase the
destination ring size to handle MSDU data buffers.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Link: https://patch.msgid.link/20241223060132.3506372-2-quic_ppranees@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently in ath12k_dp_rx_process_wbm_err(), when processing packets
received on the WBM error ring, pdev validation is done based upon the
hw_link_id. But hw_link_id corresponds to link id of a given partner pdev
in a MLO hardware group, and is not the correct index to use to lookup a
pdev in an SoC(ab). As a result, pdev validation fails, and the reaped
packets are dropped instead of being processed.
The correct index to use is the pdev_id, which is already derived in the
function. So update the logic to validate the pdev based upon the pdev_id
instead of the hw_link_id. This matches the logic used in other Rx ring
processing functions.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: 1a73acb5fb ("wifi: ath12k: move to HW link id based receive handling")
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Link: https://patch.msgid.link/20250102043048.2596791-1-quic_ramess@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Kmemleak reported this error:
unreferenced object 0xffff1c165cec3060 (size 32):
comm "insmod", pid 560, jiffies 4296964570 (age 235.596s)
backtrace:
[<000000005434db68>] __kmem_cache_alloc_node+0x1f4/0x2c0
[<000000001203b155>] kmalloc_trace+0x40/0x88
[<0000000028adc9c8>] _request_firmware+0xb8/0x608
[<00000000cad1aef7>] firmware_request_nowarn+0x50/0x80
[<000000005011a682>] local_pci_probe+0x48/0xd0
[<00000000077cd295>] pci_device_probe+0xb4/0x200
[<0000000087184c94>] really_probe+0x150/0x2c0
The firmware memory was allocated in ath12k_pci_probe(), but not
freed in ath12k_pci_remove() in case ATH12K_FLAG_QMI_FAIL bit is
set. So call ath12k_fw_unmap() to free the memory.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.2.0-02280-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Signed-off-by: Miaoqing Pan <quic_miaoqing@quicinc.com>
Reviewed-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250123080226.1116479-1-quic_miaoqing@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, when sending the scan channel list command to the firmware, the
maximum Tx power is not encoded in the reg2 member. This omission causes
the firmware to be unaware of the host's maximum Tx power, leading to
incorrect Tx power derivation at firmware level.
To resolve this issue, encode the maximum Tx power in the scan channel list
command before sending it to firmware.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: Sathishkumar Muruganandam <quic_murugana@quicinc.com>
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Tested-by: Nicolas Escande <nico.escande@gmail.com>
Link: https://patch.msgid.link/20250107-add_max_reg_pwr_in_scan_ch_list_cmd-v1-1-70d9963a21e4@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The firmware memory was allocated in ath11k_pci_probe() or
ath11k_ahb_probe(), but not freed in ath11k_xxx_remove() in case
ATH11K_FLAG_QMI_FAIL bit is set. So call ath11k_fw_destroy() to
free the memory.
Found while fixing the same problem in ath12k:
https://lore.kernel.org/linux-wireless/20240314012746.2729101-1-quic_miaoqing@quicinc.com
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-04546-QCAHSPSWPL_V1_V2_SILICONZ_IOE-1
Signed-off-by: Miaoqing Pan <quic_miaoqing@quicinc.com>
Reviewed-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250123084948.1124357-1-quic_miaoqing@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, the signal strength of "iw dev xxx station dump" always show an
invalid value.
This is because signal strength is only set in ath12k_mgmt_rx_event()
function, and not set for received data packet. So, change to get signal
from firmware and report to mac80211.
After that, "iw dev xxx station dump" show the correct signal strength.
Such as:
Station 00:03:7f:12:03:03 (on wlo1)
inactive time: 36 ms
rx bytes: 61571
rx packets: 336
tx bytes: 28204
tx packets: 205
tx retries: 49
tx failed: 0
beacon loss: 0
beacon rx: 83
rx drop misc: 66
signal: -24 dBm
beacon signal avg: -22 dBm
For WCN7850, the firmware supports db2dbm, so not need to add noise floor.
For QCN9274, the firmware not support db2dbm, so need to add noise floor.
This patch affects the station mode of WCN7850 and QCN9274.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00214-QCAHKSWPL_SILICONZ-1
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Link: https://patch.msgid.link/20250115063537.35797-4-quic_lingbok@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, the receive rate of EHT of "iw dev xxx station dump" command
always show an invalid value.
This is because ath12k does not pass information about the rx_status of EHT
to mac80211. So, mac80211 not calculate the receive rate.
To address this issue, add logic for handling rx_status of EHT to the
ath12k_dp_rx_h_rate() function.
After that, "iw dev xxx station dump" show the correct receive rate.
Such as:
Station 00:03:7f:12:03:03 (on wlo1)
inactive time: 48 ms
rx bytes: 59226
rx packets: 320
tx bytes: 26556
tx packets: 191
tx retries: 99
tx failed: 0
beacon loss: 0
beacon rx: 79
rx drop misc: 68
signal: -95 dBm
beacon signal avg: -20 dBm
tx bitrate: 688.2 MBit/s 40MHz EHT-MCS 13 EHT-NSS 2 EHT-GI 0
tx duration: 0 us
rx bitrate: 619.5 MBit/s 40MHz EHT-MCS 8 EHT-NSS 3 EHT-GI 0
This patch affects the station mode of WCN7850 and QCN9274.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00214-QCAHKSWPL_SILICONZ-1
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219715
Link: https://patch.msgid.link/20250115063537.35797-3-quic_lingbok@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, the transmit rate of "iw dev xxx station dump" command
always show an invalid value.
To address this issue, ath12k parse the info of transmit complete
report from firmware and indicate the transmit rate to mac80211.
This patch affects the station mode of WCN7850 and QCN9274.
After that, "iw dev xxx station dump" show the correct transmit rate.
Such as:
Station 00:03:7f:12:03:03 (on wlo1)
inactive time: 872 ms
rx bytes: 219111
rx packets: 1133
tx bytes: 53767
tx packets: 462
tx retries: 51
tx failed: 0
beacon loss: 0
beacon rx: 403
rx drop misc: 74
signal: -95 dBm
beacon signal avg: -18 dBm
tx bitrate: 1441.1 MBit/s 80MHz EHT-MCS 13 EHT-NSS 2 EHT-GI 0
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00214-QCAHKSWPL_SILICONZ-1
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219715
Link: https://patch.msgid.link/20250115063537.35797-2-quic_lingbok@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In the US country code, to avoid including 6 GHz rules in the 5 GHz rules
list, the number of 5 GHz rules is set to a default constant value of 4
(REG_US_5G_NUM_REG_RULES). However, if there are more than 4 valid 5 GHz
rules, the current logic will bypass the legitimate 6 GHz rules.
For example, if there are 5 valid 5 GHz rules and 1 valid 6 GHz rule, the
current logic will only consider 4 of the 5 GHz rules, treating the last
valid rule as a 6 GHz rule. Consequently, the actual 6 GHz rule is never
processed, leading to the eventual disabling of 6 GHz channels.
To fix this issue, instead of hardcoding the value to 4, use a helper
function to determine the number of 6 GHz rules present in the 5 GHz rules
list and ignore only those rules.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Cc: stable@vger.kernel.org
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250123-fix_6ghz_rules_handling-v1-1-d734bfa58ff4@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
When vlan support was added, we missed that when
ath12k_dp_prepare_htt_metadata() returns an error we also need to free
the skb holding the metadata before going on with the cleanup process.
Compile tested only.
Fixes: 26dd8ccdba ("wifi: ath12k: dynamic VLAN support")
Signed-off-by: Nicolas Escande <nico.escande@gmail.com>
Reviewed-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250122160112.3234558-1-nico.escande@gmail.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Factory test mode(FTM) is supported only in non-MLO(multi-link operation)
mode. Therefore, disable MLO when driver boots in FTM mode.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aaradhana Sahu <quic_aarasahu@quicinc.com>
Reviewed-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://patch.msgid.link/20250119083657.1937557-5-quic_aarasahu@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Add support to process factory test mode commands(FTM) for calibration.
By default firmware start with MISSION mode and to process the FTM commands
firmware needs to be restarted in FTM mode using module parameter ftm_mode.
The pre-request is all the radios should be down before starting the test.
All ath12k test mode interface related commands specified in enum
ath_tm_cmd.
When start command ATH_TM_CMD_TESTMODE_START is received, ar state
is set to test Mode and FTM daemon sends test mode command to wifi
driver via cfg80211. Wifi driver sends these command to firmware as
wmi events. If it is segmented commands it will be broken down into
multiple segments and encoded with TLV header else it is sent to
firmware as it is.
Firmware response via UTF events, wifi driver creates skb and send
to cfg80211, cfg80211 sends firmware response to FTM daemon via
netlink message.
Command to boot in ftm mode
insmod ath12k ftm_mode=1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aaradhana Sahu <quic_aarasahu@quicinc.com>
Reviewed-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://patch.msgid.link/20250119083657.1937557-4-quic_aarasahu@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Export ath12k_wmi_tlv_hdr() to further use in the testmode command
processing.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aaradhana Sahu <quic_aarasahu@quicinc.com>
Reviewed-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://patch.msgid.link/20250119083657.1937557-3-quic_aarasahu@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
User space application requires that the testmode interface
is exactly same between ath drivers. Move testmode_i.h file
in ath directory to ensure that all ath driver uses same testmode
interface instead of duplicating testmode_i.h for each ath drivers.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aaradhana Sahu <quic_aarasahu@quicinc.com>
Reviewed-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://patch.msgid.link/20250119083657.1937557-2-quic_aarasahu@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, the driver allocates cacheable DMA buffers for the rx_tid
structure using kzalloc() and dma_map_single(). These buffers are
long-lived and can persist for the lifetime of the peer, which is not
advisable. Instead of using kzalloc() and dma_map_single() for allocating
cacheable DMA buffers, utilize the dma_alloc_noncoherent() helper for the
allocation of long-lived cacheable DMA buffers, such as the peer's rx_tid.
Since dma_alloc_noncoherent() returns unaligned physical and virtual
addresses, align them internally before use within the driver. This
ensures proper allocation of non-coherent memory through the kernel
helper.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Tested-by: Tim Harvey <tharvey@gateworks.com>
Link: https://patch.msgid.link/20250119164219.647059-3-quic_ppranees@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, the driver allocates cacheable DMA buffers for rings like
HAL_REO_DST and HAL_WBM2SW_RELEASE. The buffers for HAL_WBM2SW_RELEASE
are large (1024 KiB), exceeding the SWIOTLB slot size of 256 KiB. This
leads to "swiotlb buffer is full" error messages on systems without an
IOMMU that use SWIOTLB, causing driver initialization failures. The driver
calls dma_map_single() with these large buffers obtained from kzalloc(),
resulting in ring initialization errors on systems without an IOMMU that
use SWIOTLB.
To address these issues, replace the flawed buffer allocation mechanism
with the appropriate DMA API. Specifically, use dma_alloc_noncoherent()
for cacheable DMA buffers, ensuring proper freeing of buffers with
dma_free_noncoherent().
Error log:
[ 10.194343] ath11k_pci 0000:04:00.0: swiotlb buffer is full (sz:1048583 bytes), total 32768 (slots), used 2529 (slots)
[ 10.194406] ath11k_pci 0000:04:00.0: failed to set up tcl_comp ring (0) :-12
[ 10.194781] ath11k_pci 0000:04:00.0: failed to init DP: -12
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Reported-by: Tim Harvey <tharvey@gateworks.com>
Closes: https://lore.kernel.org/all/20241210041133.GA17116@lst.de/
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Tested-by: Tim Harvey <tharvey@gateworks.com>
Link: https://patch.msgid.link/20250119164219.647059-2-quic_ppranees@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, ath12k_dp_mon_rx_parse_status_tlv() takes the TLV tag, TLV data
and TLV userid as separate arguments from the caller. In the future, the
TLV length will be needed for parsing the EHT TLV tag. Therefore, instead
of increasing the number of arguments, pass the TLV header and retrieve the
necessary fields from the TLV header itself.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241224143613.164921-4-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, the pdev handle is given along with the mac id to all the
monitor Tx/Rx handler procedure arguments. The mac id information is
derived from the pdev handle itself. Therefore, remove the unnecessary
mac id argument from the handler.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241224143613.164921-3-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, the monitor Rx parser handlers
ath12k_dp_mon_rx_parse_status_tlv() and ath12k_dp_mon_parse_rx_dest()
take the device handle from the caller. However, these handlers
functionality is technically pdev specific. Additionally, the device handle
can be retrieved from the pdev handle. Therefore, for better code
understanding, change the monitor Rx parser handlers argument from the
device handle to the pdev handle.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241224143613.164921-2-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Since 'rx_active_check_time' of 'struct ath_softc' is in jiffies,
prefer 'unsigned long' over 'u32' to avoid possible truncation in
'ath_hw_rx_inactive_check()'. Found with clang's -Wshorten-64-to-32,
compile tested only.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://patch.msgid.link/20250115171750.259917-2-dmantipov@yandex.ru
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
After switching to mac80211 software queues, pointer to 'struct ath_node'
in 'struct ath_tx_control' is still assigned but not actually used. So drop
it and cleanup related things in 'ath_tx_prepare()'. Compile tested only.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://patch.msgid.link/20250115171750.259917-1-dmantipov@yandex.ru
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, an interface is created in the driver during channel assignment.
If mac80211 attempts to set a key for an interface before this assignment,
the driver caches the key. Once the interface is created, the driver
installs the cached key to the hardware. This sequence is exemplified in
mesh mode operation where the group key is set before channel assignment.
However, in ath12k_mac_update_key_cache(), after caching the key, due to
incorrect logic, it is deleted from the cache during the subsequent loop
iteration. As a result, after the interface is created, the driver does not
find any cached key, and the key is not installed to the hardware which is
wrong. This leads to issue in mesh, where broadcast traffic is not
encrypted over the air.
Fix this issue by adjusting the logic of ath12k_mac_update_key_cache()
properly.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3-03253.1-QCAHKSWPL_SILICONZ-29 # Nicolas Escande <nico.escande@gmail.com>
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 # Nicolas Escande <nico.escande@gmail.com>
Fixes: 25e18b9d6b ("wifi: ath12k: modify ath12k_mac_op_set_key() for MLO")
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Tested-by: Nicolas Escande <nico.escande@gmail.com>
Link: https://patch.msgid.link/20250112-fix_key_cache_handling-v2-1-70e142c6153e@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, the uninitialized variable 'ab' is accessed in the
ath12k_mac_allocate() function. Initialize 'ab' with the first radio device
present in the hardware abstraction handle (ah). Additionally, move the
default setting procedure from the pdev mapping iteration to the total
radio calculating iteration for better code readability. Perform the
maximum radio validation check for total_radio to ensure that both num_hw
and radio_per_hw are validated indirectly, as these variables are derived
from total_radio. This also fixes the below Smatch static checker warning.
Smatch warning:
ath12k_mac_allocate() error: uninitialized symbol 'ab'
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Fixes: a343d97f27 ("wifi: ath12k: move struct ath12k_hw from per device to group")
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20250112071630.4059410-5-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, the ath12k_get_num_hw() helper function takes the device handle
as an argument. Here, the number of hardware is retrieved from the group
handle. Demanding the device handle from the caller is unnecessary since
in some cases the group handle is already available. Additionally, there
is no longer a need for multiple indirections to get the number of
hardware. Therefore, remove this helper function and directly use
ag->num_hw. This change also fixes the below Smatch static checker
warning.
Smatch warning:
ath12k_mac_destroy() error: we previously assumed 'ab' could be null
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/ath12k/3e705de0-67d1-4437-97ff-4828d83ae2af@stanley.mountain/
Closes: https://scan7.scan.coverity.com/#/project-view/52682/11354?selectedIssue=1602340
Fixes: a343d97f27 ("wifi: ath12k: move struct ath12k_hw from per device to group")
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Acked-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Link: https://patch.msgid.link/20250112071630.4059410-4-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, ath12k_hw is placed inside the ath12k_hw_group. However, the
ath12k_hw get helper function takes the device handle and the index as
parameters. Here, the index parameter is specific to the group handle.
Therefore, change this helper function argument from the device handle
to the group handle.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20250112071630.4059410-3-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, ath12k_hw is placed inside the ath12k_hw_group. However, the
ath12k_hw set helper function takes the device handle and the index as
parameters. Here, the index parameter is specific to the group handle.
Therefore, change this helper function argument from the device handle to
the group handle.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20250112071630.4059410-2-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Commit b35108a51c ("jiffies: Define secs_to_jiffies()") introduced
secs_to_jiffies(). As the value here is a multiple of 1000, use
secs_to_jiffies() instead of msecs_to_jiffies to avoid the multiplication.
This is converted using scripts/coccinelle/misc/secs_to_jiffies.cocci with
the following Coccinelle rules:
@@ constant C; @@
- msecs_to_jiffies(C * 1000)
+ secs_to_jiffies(C)
@@ constant C; @@
- msecs_to_jiffies(C * MSEC_PER_SEC)
+ secs_to_jiffies(C)
Link: https://lkml.kernel.org/r/20241210-converge-secs-to-jiffies-v3-14-ddfefd7e9f2a@linux.microsoft.com
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Easwar Hariharan <eahariha@linux.microsoft.com>
Cc: Alexander Gordeev <agordeev@linux.ibm.com>
Cc: Andrew Lunn <andrew+netdev@lunn.ch>
Cc: Anna-Maria Behnsen <anna-maria@linutronix.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christian Borntraeger <borntraeger@linux.ibm.com>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Daniel Mack <daniel@zonque.org>
Cc: David Airlie <airlied@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Florian Fainelli <florian.fainelli@broadcom.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Ilya Dryomov <idryomov@gmail.com>
Cc: Jack Wang <jinpu.wang@cloud.ionos.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: James Smart <james.smart@broadcom.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Jeff Johnson <jjohnson@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Jeroen de Borst <jeroendb@google.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Joe Lawrence <joe.lawrence@redhat.com>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Josh Poimboeuf <jpoimboe@kernel.org>
Cc: Jozsef Kadlecsik <kadlec@netfilter.org>
Cc: Julia Lawall <julia.lawall@inria.fr>
Cc: Kalle Valo <kvalo@kernel.org>
Cc: Louis Peens <louis.peens@corigine.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Madhavan Srinivasan <maddy@linux.ibm.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Miroslav Benes <mbenes@suse.cz>
Cc: Naveen N Rao <naveen@kernel.org>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Nicolas Palix <nicolas.palix@imag.fr>
Cc: Oded Gabbay <ogabbay@kernel.org>
Cc: Ofir Bitton <obitton@habana.ai>
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Praveen Kaligineedi <pkaligineedi@google.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Roger Pau Monné <roger.pau@citrix.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: Shailend Chand <shailend@google.com>
Cc: Simona Vetter <simona@ffwll.ch>
Cc: Simon Horman <horms@kernel.org>
Cc: Sven Schnelle <svens@linux.ibm.com>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Xiubo Li <xiubli@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
In 'ath9k_hw_get_nf_hist_mid()', prefer 'memcpy()' and 'sort()'
over an ad-hoc things. Briefly tested as a separate module.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://patch.msgid.link/20250109080703.106692-1-dmantipov@yandex.ru
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, when the vdev start WMI cmd is sent from host, vdev related
parameters such as max_reg_power, max_power, and max_antenna_gain are
multiplied by 2 before being sent to the firmware. This is incorrect
because the firmware uses 1 dBm steps for power calculations.
This leads to incorrect power values being used in the firmware and
radio, potentially causing incorrect behavior.
Fix the update of max_reg_power, max_power, and max_antenna_gain values
in the ath12k_mac_vdev_start_restart function, ensuring accurate
power settings in the firmware by sending these values as-is,
without multiplication.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00214-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sathishkumar Muruganandam <quic_murugana@quicinc.com>
Signed-off-by: Santhosh Ramesh <quic_santrame@quicinc.com>
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20240909073049.3423035-1-quic_santrame@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
IEEE80211_TX_STAT_NOACK_TRANSMITTED flag signifies that frame was
successfully transmitted without any errors when no-ack is requested.
In WMI Tx management completion path, driver is not setting
IEEE80211_TX_STAT_NOACK_TRANSMITTED flag for the frames with
IEEE80211_TX_CTL_NO_ACK. Without this flag, the management frame
statistics will not track such frames.
Add IEEE80211_TX_STAT_NOACK_TRANSMITTED flag as part of the flags in
skb transmit information when WMI is processing Tx completion for
management frames.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Signed-off-by: Muna Sinada <quic_msinada@quicinc.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241219190845.605116-1-quic_msinada@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The current firmware coredump collection in ath12k does not include
the MLO_GLOBAL_MEM_REGION_TYPE memory. This memory region is essential
for debugging issues related to Multi-Link Operation (MLO).
Hence, add support to include MLO_GLOBAL_MEM_REGION_TYPE memory in
firmware coredump collection.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241218040149.4041728-1-quic_rajkbhag@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
ieee80211_radar_detected() expects the driver to pass a channel context
configuration during MLO. This is used to identify exactly which link
detected the radar.
Add support to pass this to mac80211. Since the link arvif is not known in
the WMI event, introduce a helper iterator API,
ath12k_mac_get_any_chanctx_conf_iter(), to get the channel context
configuration.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241218-ath12k_mlo_dfs-v1-3-058e783bcfc7@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, the DFS CAC time and the usable state of the primary channel in
the channel definition are used to set the CAC_RUNNING flag for the ath12k
radio structure. However, this approach is flawed because there are channel
definitions where the primary channel is not a DFS channel, but the
secondary channel is. For example, in 5 GHz band, channel 36 with 160 MHz
bandwidth. In such cases, the flag is not set correctly and hence places
where this flag is tested will not operate as expected. For example, Rx
packets will not be dropped.
To fix this issue, use the cfg80211_chandef_dfs_usable() function from
cfg80211, which returns true if at least one channel is in a usable state.
This will ensure the CAC_RUNNING flag is set properly.
Additionally, update the CAC running debug log message to include the CAC
time in milliseconds and also print the center frequency segment 1.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241218-ath12k_mlo_dfs-v1-2-058e783bcfc7@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Rename the flag ATH12K_CAC_RUNNING to ATH12K_FLAG_CAC_RUNNING to correct
the naming inconsistency in the enum ath12k_dev_flags.
No functionality changes.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241218-ath12k_mlo_dfs-v1-1-058e783bcfc7@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
There is a spelling mistake in an ath12k_err error message. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241217105505.306047-1-colin.i.king@gmail.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, monitor status parse procedure handles all the supported TLV
tags. Each TLV tag has its own data structure for parsing. Now, this
handler is passed the tlv_data as a u8 pointer, so explicit type cast
conversion happens for every TLV tag parsing. Therefore, avoid the
explicit type conversion by changing the tlv_data type from a u8 pointer
to a const void pointer.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241217084511.2981515-9-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The Tx monitor SRNG ring ID does not align with the ath12k 802.11be
hardware architecture. Currently, there is no issue since the Tx monitor
is not enabled. However, in the future, the Tx monitor will be enabled.
Therefore, change the HAL_SRNG_RING_ID_WMAC1_SW2TXMON_BUF0 SRNG ID and
assign the correct start ring ID for the ring type HAL_TX_MONITOR_BUF.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241217084511.2981515-8-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, CODING and TXBF are unused masks defined in the HAL Rx monitor
status TLV parsing code path. Therefore, remove the unused masks to
prevent incorrect assumptions for code readers.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241217084511.2981515-7-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
