Add Nuvoton NCT7201/NCT7202 system voltage monitor 12-bit ADC driver
NCT7201/NCT7202 supports up to 12 analog voltage monitor inputs and up
to 4 SMBus addresses by ADDR pin. Meanwhile, ALERT# hardware event pins
for independent alarm signals, and all the threshold values could be set
for system protection without any timing delay. It also supports reset
input RSTIN# to recover system from a fault condition.
Currently, only single-edge mode conversion and threshold events are
supported.
Signed-off-by: Eason Yang <j2anfernee@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20250512083156.3300006-3-j2anfernee@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Remove kernel.h since it adds a lot of unnecessary dependencies.
Add specific headers to ensure all functions and macros used in the driver
are directly declared.
Suggested-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Jonathan Santos <Jonathan.Santos@analog.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://patch.msgid.link/1f7677d31a0165cb30d7eb3b4d613e1337937f9a.1746662899.git.Jonathan.Santos@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use IIO_DECLARE_BUFFER_WITH_TS() to declare the buffer that gets used
with iio_push_to_buffers_with_ts(). This makes the code a bit easier to
read and understand.
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250507-iio-introduce-iio_declare_buffer_with_ts-v6-7-4aee1b9f1b89@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use IIO_DECLARE_DMA_BUFFER_WITH_TS() to declare the buffer that gets
used with iio_push_to_buffers_with_ts(). This makes the code a bit
easier to read and understand.
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250507-iio-introduce-iio_declare_buffer_with_ts-v6-5-4aee1b9f1b89@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Rename AD4695_MAX_CHANNELS to AD4695_MAX_VIN_CHANNELS. It has been a
point of confusion that this macro is only the voltage input channels
and not all channels.
Reviewed-by: Trevor Gamblin <tgamblin@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250507-iio-introduce-iio_declare_buffer_with_ts-v6-4-4aee1b9f1b89@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use IIO_DECLARE_DMA_BUFFER_WITH_TS() to declare the buffer that gets
used with iio_push_to_buffers_with_ts(). This makes the code a bit
easier to read and understand.
Reviewed-by: Trevor Gamblin <tgamblin@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250507-iio-introduce-iio_declare_buffer_with_ts-v6-3-4aee1b9f1b89@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Remove setting bits_per_word = 8 from the ti-tsc2046 driver. This is the
default value for SPI transfers, so it is not necessary to explicitly
set it.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250505-iio-remove-bits_per_word-8-v1-2-341f85fcfe11@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Remove setting bits_per_word = 8 from the ad4030 driver. This is the
default value for SPI transfers, so it is not necessary to explicitly
set it.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250505-iio-remove-bits_per_word-8-v1-1-341f85fcfe11@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
According to Jonathan, variable reference voltages are very rare. It is
unlikely it is needed, and supporting it makes the code a bit more
complex.
Simplify the driver and drop the variable vref support.
Suggested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/59106e24332743a7f9eb0b13ad6a2f5595ab485a.1745823530.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Currently, SPI-Engine offload module always sends 32-bit data elements to
DMA engine. Appropriately, when set for SPI offloading, the IIO driver uses
32 storagebits for IIO ADC channel buffer elements. However, setting SPI
transfer length according to storagebits (32-bits in case of offload) can
lead to unnecessarily long transfers for ADCs that are 16-bit or less
precision. Adjust AD4000 single-shot read to run transfers of 2 bytes when
that is enough to get all ADC data bits.
Fixes: 59b51edf71 ("iio: adc: ad4000: Add support for SPI offload")
Suggested-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Marcelo Schmitt <marcelo.schmitt@analog.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/8f765cfd6e93fad4e755dd95d709b7bea2a388e2.1744718916.git.marcelo.schmitt@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for optional HW reset.
If specified, a reset will be asserted during driver probe.
Co-developed-by: Lukas Rauber <lukas.rauber@janitza.de>
Signed-off-by: Lukas Rauber <lukas.rauber@janitza.de>
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20250428-mcp3911-fixes-v2-3-406e39330c3d@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The conversion result registers differs between devices. Make sure the
mapping is correct by using a device dependent .get_raw() callback function.
Fixes: 732ad34260 ("iio: adc: mcp3911: add support for the whole MCP39xx family")
Co-developed-by: Lukas Rauber <lukas.rauber@janitza.de>
Signed-off-by: Lukas Rauber <lukas.rauber@janitza.de>
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20250428-mcp3911-fixes-v2-1-406e39330c3d@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Change the type of the buffer elements to u16 since we currently only
support 16-bit word size. The code was originally written to also allow
for 32-bit word size when oversampling is enabled, but so far,
oversampling is only implemented when using SPI offload and therefore
doesn't use this buffer.
AD4695_MAX_CHANNEL_SIZE macro is dropped since it no longer adds any
value.
AD4695_MAX_CHANNELS + 2 is changed to AD4695_MAX_CHANNELS + 1 because
previously we were overallocating. AD4695_MAX_CHANNELS is the number of
of voltage channels and + 1 is for the temperature channel.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Trevor Gamblin <tgamblin@baylibre.com>
Link: https://patch.msgid.link/20250428-iio-introduce-iio_declare_buffer_with_ts-v4-2-6f7f6126f1cb@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use struct with aligned_s64 timestamp to make timestamp alignment
explicit. Technically, what we have works because for all known
architectures, IIO_DMA_MINALIGN is a multiple of __alignof__(s64).
But this way, we don't have to make people read the comments to know
why there are extra elements in each buffer.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250428-iio-adc-ad7606-fix-buffer-alignment-v1-1-88dfc57e5df0@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Validate the scan mask when SPI offloading is being used.
Since this family of ADCs is simultaneous sampling, there isn't a way
to selectively disable channels when reading sample data. (Technically,
AD7616 has a sequencer so the driver could have some control, but that
is for another day).
For "regular" IIO triggered buffer reads, this isn't a problem and the
IIO core will demux the data and ignore data from disabled channels.
However, since SPI offloading is done completely in hardware, we don't
have a way to do the same. So before this patch, if less than all
channels were enabled, the data would be misplaced in the buffer.
By adding a check in update_scan_mode, we can fail to enable the buffer
instead of having bad data returned to userspace.
Fixes: e96d35faf3 ("iio: adc: ad7606: add SPI offload support")
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250502-iio-adc-ad7606_spi-fix-offload-scan-mask-check-v2-1-e70c6d71baa3@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Both ad7091r_writeable_reg() and ad7091r_volatile_reg() perform the
same test, checking whether a given 'reg' code is
AD7091R_REG_RESULT or AD7091R_REG_ALERT. As the volatile ad7091r
registers happen to be the only read-only ones, the volatile_reg()
function now returns the negated output of writeable_reg().
Co-developed-by: Bruno Stephan <bruno.stephan@usp.br>
Signed-off-by: Bruno Stephan <bruno.stephan@usp.br>
Co-developed-by: Andre de Lima <aschwarz@usp.br>
Signed-off-by: Andre de Lima <aschwarz@usp.br>
Signed-off-by: Arthur Pilone <art.pilone@gmail.com>
Reviewed-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Link: https://patch.msgid.link/20250421145534.91146-1-arthurpilone@usp.br
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add oversampling support for STM32H7, STM32MP15 & STM32MP13.
STM32F4 ADC has no oversampling feature.
The current support of the oversampling feature aims at increasing the
data SNR, without changing the data resolution.
As the oversampling by itself increases data resolution, a right shift
is applied to keep the initial resolution.
Only the oversampling ratio corresponding to a power of two are
supported here, to get a direct link between right shift and
oversampling ratio. (2^n ratio <=> n right shift)
The oversampling ratio is shared by all channels, whatever channel type.
(e.g. single ended or differential).
Oversampling can be configured using IIO ABI:
- oversampling_ratio_available
- oversampling_ratio
Co-developed-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://patch.msgid.link/20250424151604.626758-1-olivier.moysan@foss.st.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use a struct with aligned s64_timestamp instead of a padded array for
the buffer used for iio_push_to_buffers_with_ts(). This makes it easier
to see the correctness of the size and alignment of the buffer.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250418-iio-prefer-aligned_s64-timestamp-v1-3-4c6080710516@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Follow the pattern of other drivers and use aligned_s64 for the
timestamp. This will ensure that the timestamp is correctly aligned on
all architectures. It also ensures that the struct itself it also 8-byte
aligned so we can drop the explicit __aligned(8) attribute.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250417-iio-more-timestamp-alignment-v1-2-eafac1e22318@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This new function allows us to perform debug checks in the helper to ensure
that the overrun does not occur. Use it in all the simple cases where
either a static buffer or a structure is used in the drivers.
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250413103443.2420727-10-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
By providing the size of the buffer used, runtime checks can be performed
to ensure not overrun.
Also change the pushed data pointer to be that of the structure that also
contains the timestamp. Not an actual bug but semantically incorrect to
push the channel data when we want the storage with the timestamp as well.
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250413103443.2420727-9-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
irq_domain_add_simple() is going away as being obsolete now. Switch to
the preferred irq_domain_create_simple(). That differs in the first
parameter: It takes more generic struct fwnode_handle instead of struct
device_node. Therefore, of_fwnode_handle() is added around the
parameter.
Note some of the users can likely use dev->fwnode directly instead of
indirect of_fwnode_handle(dev->of_node). But dev->fwnode is not
guaranteed to be set for all, so this has to be investigated on case to
case basis (by people who can actually test with the HW).
[ tglx: Fix up subject prefix ]
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250319092951.37667-21-jirislaby@kernel.org
Apply a mask to the raw value received over the SPI bus for unsigned
direct reads. As we found recently, SPI controllers may not set unused
bits to 0 when reading with bits_per_word != {8,16,32}. The ad7944 uses
bits_per_word of 14 and 18, so we need to mask the value to be sure we
returning the correct value to userspace during a direct read.
Fixes: d1efcf8871 ("iio: adc: ad7944: add driver for AD7944/AD7985/AD7986")
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250505-iio-adc-ad7944-max-high-bits-on-direct-read-v1-1-b173facceefe@baylibre.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The pointer returned from ad4851_parse_channels_common() is incremented
internally as each channel is populated. In ad4858_parse_channels(),
the same pointer was further incremented while setting ext_scan_type
fields for each channel. This resulted in indio_dev->channels being set
to a pointer past the end of the allocated array, potentially causing
memory corruption or undefined behavior.
Fix this by iterating over the channels using an explicit index instead
of incrementing the pointer. This preserves the original base pointer
and ensures all channel metadata is set correctly.
Fixes: 6250803fe2 ("iio: adc: ad4851: add ad485x driver")
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250509101657.6742-1-antoniu.miclaus@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix incorrect value mask for register write. Register values are 8-bit,
not 9. If this function was called with a value > 0xFF and an even addr,
it would cause writing to the next register.
Fixes: f2a22e1e17 ("iio: adc: ad7606: Add support for software mode for ad7616")
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Angelo Dureghello <adureghello@baylibre.com>
Link: https://patch.msgid.link/20250428-iio-adc-ad7606_spi-fix-write-value-mask-v1-1-a2d5e85a809f@baylibre.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix 18-bit raw read for 18-bit chips by applying a mask to the value
we receive from the SPI controller.
SPI controllers either return 1, 2 or 4 bytes per word depending on the
bits_per_word. For 16-bit chips, there was no problem since they raw
data fit exactly in the 2 bytes received from the SPI controller. But
now that we have 18-bit chips and we are using bits_per_word = 18, we
cannot assume that the extra bits in the 32-bit word are always zero.
In fact, with the AXI SPI Engine controller, these bits are not always
zero which caused the raw values to read 10s of 1000s of volts instead
of the correct value. Therefore, we need to mask the value we receive
from the SPI controller to ensure that only the 18 bits of real data
are used.
Fixes: f3838e934d ("iio: adc: ad7606: add support for AD7606C-{16,18} parts")
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250502-iio-adc-ad7606-fix-raw-read-for-18-bit-chips-v1-1-06caa92d8f11@baylibre.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix compiling the ad7173 driver when CONFIG_GPIOLIB is not set by
selecting GPIOLIB to be always enabled and remove the #if.
Commit 031bdc8aee ("iio: adc: ad7173: add calibration support") placed
unrelated code in the middle of the #if IS_ENABLED(CONFIG_GPIOLIB) block
which caused the reported compile error.
However, later commit 7530ed2aaa ("iio: adc: ad7173: add openwire
detection support for single conversions") makes use of the gpio regmap
even when we aren't providing gpio controller support. So it makes more
sense to always enable GPIOLIB rather than trying to make it optional.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202504220824.HVrTVov1-lkp@intel.com/
Fixes: 031bdc8aee ("iio: adc: ad7173: add calibration support")
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250422-iio-adc-ad7173-fix-compile-without-gpiolib-v1-1-295f2c990754@baylibre.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use `\t(\{ ?\},|\{\}|\{\s*/\*.*\*/\s*\},?)$` regex to find and replace
the array sentinel in all IIO drivers to the same style.
For some time, we've been trying to consistently use `{ }` (no trailing
comma, no comment, one space between braces) for array sentinels in the
IIO subsystem. Still nearly 50% of existing code uses a different style.
To save reviewers from having to request this trivial change as
frequently, let's normalize the style in all existing IIO drivers.
At least when code is copy/pasted to new drivers, the style will be
consistent.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://patch.msgid.link/20250411-iio-sentinel-normalization-v1-1-d293de3e3d93@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This change moves the buffer allocation and related trigger allocation
in a separate function, making space for adding another type of iio
buffer if needed.
Reviewed-by: Marcelo Schmitt <marcelo.schmitt@analog.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Signed-off-by: Jonathan Santos <Jonathan.Santos@analog.com>
Link: https://patch.msgid.link/11c1777b406875ce1a7216dc4b094ff99af8da7f.1744325346.git.Jonathan.Santos@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Convert the AD7768-1 driver to use the regmap API for register
access. This change simplifies and standardizes register interactions,
reducing code duplication and improving maintainability.
Create two regmap configurations, one for 8-bit register values and
other for 24-bit register values.
Since we are using regmap now, define the remaining registers from 0x32
to 0x34.
Reviewed-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Jonathan Santos <Jonathan.Santos@analog.com>
Link: https://patch.msgid.link/aec9e5452c1ac16d5379a80dfce97c00d85614a2.1744325346.git.Jonathan.Santos@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix Smatch-detected issue:
drivers/iio/adc/ad_sigma_delta.c:604 ad_sd_trigger_handler() error:
uninitialized symbol 'status_pos'.
The variable `status_pos` was only initialized in specific switch cases
(1, 2, 3, 4), which could leave it uninitialized if `reg_size` had an
unexpected value.
Fix by adding a default case to the switch block to catch unexpected
values of `reg_size`. Use `dev_err_ratelimited()` for error logging and
`goto irq_handled` instead of returning early.
Signed-off-by: Purva Yeshi <purvayeshi550@gmail.com>
Link: https://patch.msgid.link/20250410170408.8585-1-purvayeshi550@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ROHM BD79104 ADC has identical SPI communication logic as the
ti-adc128s052. Eg, SPI transfer should be 16 clk cycles, conversion is
started when the CS is pulled low, and channel selection is done by
writing the channel ID after two zero bits. Data is contained in
big-endian format in the last 12 bits.
The BD79104 has two input voltage pins. Data sheet uses terms "vdd" and
"iovdd". The "vdd" is used also as an analog reference voltage. Hence
the driver expects finding these from the device-tree, instead of having
the "vref" only as TI's driver.
NOTE: The TI's data sheet[1] does show that the TI's IC does actually
have two voltage inputs as well. Pins are called Va (analog reference)
and Vd (digital supply pin) - but I keep the existing driver behaviour
for the TI's IC "as is", because I have no HW to test changes, and
because I have no real need to touch it.
NOTE II: The BD79104 requires SPI MODE 3.
NOTE III: I used evaluation board "BD79104FV-EVK-001" made by ROHM. With
this board I had to drop the SPI speed below the 20M which is mentioned
in the data-sheet [2]. This, however, may be a limitation of the EVK
board, not the component itself.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Datasheet: https://www.ti.com/lit/ds/symlink/adc128s052.pdf # [1]
Datasheet: https://fscdn.rohm.com/en/products/databook/datasheet/ic/data_converter/dac/bd79104fv-la-e.pdf # [2]
Link: https://patch.msgid.link/36ffa72cbdf8dbbdf1e612040db82ebcdf73fa24.1744022065.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Quoting Jonathan:
"Whilst it doesn't bring huge advantage, now we have devm_mutex_init()
it seems reasonable to use it and maybe catch a use after free for the
lock"
Switch to use devm_mutex_init() while working on this file.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://patch.msgid.link/efe4a039e2bfbf4dcf30743f6b7b88fce3b9ee39.1744022065.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ti-adc128s052 driver has NULL terminated ID arrays for the
of_device_id, spi_device_id and acpi_device_id. All of these are
terminated by having an empty string as the last member of an array.
Only the of_device_id array uses the /* sentinel */ comment.
It's better to be consistent.
This /* sentinel */ comment serves no real purpose these days as people
are used to seeing these ID lists terminated with an empty array
element.
Drop the /* sentinel */ from the of_device_id.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://patch.msgid.link/bb58002accc696bd4a8fbbab37100c6fa0c29941.1744022065.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
struct gpio_chip now has callbacks for setting line values that return
an integer, allowing to indicate failures. Convert the driver to using
them.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250409-gpiochip-set-rv-iio-v2-5-4b36428f39cb@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
struct gpio_chip now has callbacks for setting line values that return
an integer, allowing to indicate failures. Convert the driver to using
them.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250409-gpiochip-set-rv-iio-v2-4-4b36428f39cb@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The new GPIO callbacks 'set_rv' and 'set_multiple_rv' allow returning a
success code to indicate failures when setting GPIO status. Use them to
allow callers to know when things go south.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://patch.msgid.link/Z_N_J52IZ2IaWawl@mva-rohm
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add chip info for AD7389-4 to the ad7380 driver.
This is essentially the same as ad7380-4 except that it is internal-
reference-only instead of external-reference-only.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250401-iio-ad7380-add-ad7389-4-v1-4-23d2568aa24f@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move the internal reference voltage value to the chip_info structure.
Before this change, only ADAQ chips could be internal_ref_only and only
non-ADAQ chips could be external_ref_only. Now, this restriction is
removed.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250401-iio-ad7380-add-ad7389-4-v1-3-23d2568aa24f@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Rename adaq_internal_ref_only to internal_ref_only_adaq. There are non-
ADAQ chips in the family that are also internal reference only, so the
adaq_ prefix is misleading.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250401-iio-ad7380-add-ad7389-4-v1-2-23d2568aa24f@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cleanup definition of register related constants:
- Use the register and field names exactly as documented in the data
sheet.
- Consistently use <regname>_<bitfield> to name a register's bitfield.
- Drop _MSK definitions and implicit FIELD_PREP calls.
- Consistent indentation.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/20250317115247.3735016-8-u.kleine-koenig@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There are several issues with the function that implements writing to
the filter_low_pass_3db_frequency property:
- The sinc3 factor should be 0.272 not 0.262 (this is fixed for the
reading side in the previous patch).
- For freq > 1 the if condition is always true so the sinc4 filter is
hardly ever chosen.
- In the nearly always taken if branch the filter is set to sinc3, but
the frequency is set for sinc4. (And vice versa in the else branch.)
This is broken enough to justify the claim that there isn't any serious
user. Also it it counter-intuitive that setting the 3db frequency
modifies the sample frequency and the filter type.
So drop the ability to write that property.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Reviewed-by: Marcelo Schmitt <marcelo.schmitt@analog.com>
Link: https://patch.msgid.link/20250317115247.3735016-7-u.kleine-koenig@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The sinc4 filter has a factor 0.23 between Output Data Rate and f_{3dB}
and for sinc3 the factor is 0.272 according to the data sheets for
ad7124-4 (Rev. E.) and ad7124-8 (Rev. F).
Fixes: cef2760954 ("iio: adc: ad7124: add 3db filter")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Reviewed-by: Marcelo Schmitt <marcelo.schmitt@analog.com>
Link: https://patch.msgid.link/20250317115247.3735016-6-u.kleine-koenig@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
FPGA HDL projects can include a PWM generator in addition to SPI-Engine.
The PWM IP is used to trigger SPI-Engine offload modules that in turn set
SPI-Engine to execute transfers to poll data from the ADC. That allows data
to be read at the maximum sample rates. Also, it is possible to set a
specific sample rate by setting the proper PWM duty cycle and related state
parameters, thus allowing an adjustable ADC sample rate when a PWM (offload
trigger) is used in combination with SPI-Engine.
Add support for SPI offload.
Signed-off-by: Marcelo Schmitt <marcelo.schmitt@analog.com>
Link: https://patch.msgid.link/386ce043a0e3fc9e8ff71f17aef8de128ce5869e.1743110188.git.marcelo.schmitt@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Remove setting bits_per_word in SPI xfers without data. The shortcoming
that this was working around was fixed in the SPI controller driver, so
it is no longer necessary. And we don't need this to be cargo-culted to
new drivers.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250331-iio-adc-ad7944-drop-bits_per_word-hack-v1-1-2b952e033340@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
These new functions allow sparse to find failures to release
direct mode reducing chances of bugs over the claim_direct_mode()
functions that are deprecated.
Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250309165819.1346684-9-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
These new functions allow sparse to find failures to release
direct mode reducing chances of bugs over the claim_direct_mode()
functions that are deprecated.
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250309165819.1346684-8-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
These new functions allow sparse to find failures to release
direct mode reducing chances of bugs over the claim_direct_mode()
functions that are deprecated.
Cc: Marek Vasut <marex@denx.de>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250309165819.1346684-7-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
By use of automatic lock release and introducing a new utility
function to handle the core activity of reading the ADC channel,
many more complex code flows can be replaced by direct returns.
Cc: Marek Vasut <marex@denx.de>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250309165819.1346684-6-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
These new functions allow sparse to find failures to release
direct mode reducing chances of bugs over the claim_direct_mode()
functions that are deprecated.
Cc: Mike Looijmans <mike.looijmans@topic.nl>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250309165819.1346684-5-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use of automated lock release simplifies the code.
Cc: Mike Looijmans <mike.looijmans@topic.nl>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250309165819.1346684-4-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
These new functions allow sparse to find failures to release
direct mode reducing chances of bugs over the claim_direct_mode()
functions that are deprecated.
Cc: Frank Li <Frank.Li@nxp.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250309165819.1346684-3-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
These two changes allow direct returns in all paths, improving code
readablity.
Cc: Frank Li <Frank.Li@nxp.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250309165819.1346684-2-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Refactor the ad7606 drivers to dynamically allocate the channel info.
The channel info was getting a bit unwieldy. In some cases, the
indio_dev->channels field was getting assigned up to 3 different times,
each in a different function, making it difficult to see where the info
was coming from. This problem stems from the number of permutations of
the channel array needed to support various modes of operation and data
buses. We already have 4 per chip (hardware mode, software mode, AXI ADC
backend and AXI ADC backend with software mode) and we intend to add two
more per chip when adding SPI offload support.
To make it easier to read and maintain, move all of the channel setup
to a single function that dynamically allocates and fills in the channel
info.
Additionally, this lets us remove some hacks where we had to compute an
offset due to the fact that sometimes there was a soft timestamp channel
at the start of the array. Now the timestamp channel is always at the
end of the array as is typical in other drivers.
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250318-iio-adc-ad7606-improvements-v2-9-4b605427774c@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Drop the ch parameter from the ad7606_scale_setup_cb_t functions. The
same info is already available from the chan param via chan->scan_type
and chan->channel, so the parameter is redundant.
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250318-iio-adc-ad7606-improvements-v2-8-4b605427774c@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Drop use of the address field in the ad7606 driver. This field was
duplicating the same info that was already in the channel and scan_index
fields. This is one less thing to have to hold in your mind when reading
the code.
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250318-iio-adc-ad7606-improvements-v2-7-4b605427774c@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix several issues with kernel-doc comments in ad7606.h:
* Add missing ":" to @param names.
* Fix order of @param names.
* Add some missing parameters.
* Remove some non-existent parameters.
* Fix alignment and wrapping.
* Fix some spelling.
`./scripts/kernel-doc -v -none drivers/iio/adc/ad7606*` is happy now.
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250318-iio-adc-ad7606-improvements-v2-5-4b605427774c@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use devm_mutex_init() in ad7606_probe(). Mutexes should be cleaned up
on driver removal.
Also add missing include while we are touching this.
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250318-iio-adc-ad7606-improvements-v2-4-4b605427774c@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add max sample rates for all of the chips. Previously, only one chip had
this field populated. The fallback value for the initial sampling
frequency can be removed now that all chips have a max sample rate
defined.
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250318-iio-adc-ad7606-improvements-v2-3-4b605427774c@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ROHM BD79124 is a 12-bit, 8-channel, SAR ADC. The ADC supports
an automatic measurement mode, with an alarm interrupt for out-of-window
measurements. The window is configurable for each channel.
The I2C protocol for manual start of the measurement and data reading is
somewhat peculiar. It requires the master to do clock stretching after
sending the I2C slave-address until the slave has captured the data.
Needless to say this is not well suopported by the I2C controllers.
Thus do not support the BD79124's manual measurement mode but implement
the measurements using automatic measurement mode, relying on the
BD79124's ability of storing latest measurements into register.
Support also configuring the threshold events for detecting the
out-of-window events.
The BD79124 keeps asserting IRQ for as long as the measured voltage is
out of the configured window. Thus, prevent the user-space from choking
on the events and mask the received event for a fixed duration (1 second)
when an event is handled.
The ADC input pins can be also configured as general purpose outputs.
Make those pins which don't have corresponding ADC channel node in the
device-tree controllable as GPO.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://patch.msgid.link/ca3886c9abcb268ca976e62cd7da28bf5d6e6382.1742560649.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The new devm_iio_adc_device_alloc_chaninfo_se() -helper is intended to
help drivers avoid open-coding the for_each_node -loop for getting the
channel IDs. The helper provides standard way to detect the ADC channel
nodes (by the node name), and a standard way to convert the "reg"
-properties to channel identification numbers, used in the struct
iio_chan_spec. Furthermore, the helper can optionally check the found
channel IDs are smaller than given maximum. This is useful for callers
which later use the IDs for example for indexing a channel data array.
The original driver treated all found child nodes as channel nodes. The
new helper requires channel nodes to be named channel[@N]. This should
help avoid problems with devices which may contain also other but ADC
child nodes. Quick grep from arch/* with the sun20i-gpadc's compatible
string didn't reveal any in-tree .dts with channel nodes named
otherwise. Also, same grep shows all the in-tree .dts seem to have
channel IDs between 0..num of channels.
Use the new helper.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/e367a803c0d625e60c9fca16c55a25eee06b5a89.1742560649.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The new devm_iio_adc_device_alloc_chaninfo_se() -helper is intended to
help drivers avoid open-coding the for_each_node -loop for getting the
channel IDs. The helper provides standard way to detect the ADC channel
nodes (by the node name), and a standard way to convert the "reg"
-properties to channel identification numbers, used in the struct
iio_chan_spec. Furthermore, the helper can optionally check the found
channel IDs are smaller than given maximum. This is useful for callers
which later use the IDs for example for indexing a channel data array.
The original driver treated all found child nodes as channel nodes. The
new helper requires channel nodes to be named channel[@N]. This should
help avoid problems with devices which may contain also other but ADC
child nodes. Quick grep from arch/* with the rzg2l_adc's compatible
string didn't reveal any in-tree .dts with channel nodes named
otherwise. Also, same grep shows all the .dts seem to have channel IDs
between 0..num of channels.
Use the new helper.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://patch.msgid.link/e84ccff01070eaee3dd1ae2d7e109f963168f586.1742560649.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There are ADC ICs which may have some of the AIN pins usable for other
functions. These ICs may have some of the AIN pins wired so that they
should not be used for ADC.
A common way of marking pins that can be used as ADC inputs is to add
corresponding channel@N nodes in the device tree as described in the ADC
binding yaml.
Add couple of helper functions which can be used to retrieve the channel
information from the device node.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Link: https://patch.msgid.link/f1d8b3e15237947738912c0d297b3e1e21d8b03e.1742560649.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The SARADC IP on the GXLX SoC itself is identical to the one found on
GXL SoCs. However, GXLX SoCs require poking the first three bits in the
MESON_SAR_ADC_REG12 register to get the three MPLL clocks (used as clock
generators for the audio frequencies) to work.
The reason why there are MPLL clock bits in the ADC register space is
entirely unknown and it seems that nobody is able to comment on this.
So clearly mark this as a workaround and add a warning so users are
notified that this workaround can change (once we know what these bits
actually do).
Tested-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://patch.msgid.link/20250330101922.1942169-3-martin.blumenstingl@googlemail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix register read/write routine as per datasheet.
When reading multiple consecutive registers, only the first one is read
properly. This is due to missing chip select deassert and assert again
between first and second 16bit transfer, as shown in the datasheet
AD7606C-16, rev 0, figure 110.
Fixes: f2a22e1e17 ("iio: adc: ad7606: Add support for software mode for ad7616")
Reviewed-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Angelo Dureghello <adureghello@baylibre.com>
Link: https://patch.msgid.link/20250418-wip-bl-ad7606-fix-reg-access-v3-1-d5eeb440c738@baylibre.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
On architectures where an s64 is only 32-bit aligned insufficient padding
would be left between the earlier elements and the timestamp. Use
aligned_s64 to enforce the correct placement and ensure the storage is
large enough.
Fixes: 54e018da31 ("iio:ad7266: Mark transfer buffer as __be16") # aligned_s64 is much newer.
Reported-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250413103443.2420727-2-jic23@kernel.org
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
On architectures where an s64 is not 64-bit aligned, this may result
insufficient alignment of the timestamp and the structure being too small.
Use aligned_s64 to force the alignment.
Fixes: a1caeebab0 ("iio: adc: ad7768-1: Fix too small buffer passed to iio_push_to_buffers_with_timestamp()") # aligned_s64 newer
Reported-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250413103443.2420727-3-jic23@kernel.org
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Here the lack of marking allows the overall structure to not be
sufficiently aligned resulting in misplacement of the timestamp
in iio_push_to_buffers_with_timestamp(). Use aligned_s64 to
force the alignment on all architectures.
Fixes: 7c0299e879 ("iio: adc: Add support for DLN2 ADC")
Reported-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250413103443.2420727-4-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add a comment explaining why the raw sample data is rearranged in the
in the ad4030_conversion() function. It is not so obvious from the code
why this is done.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250310-iio-adc-ad4030-check-scan-type-err-v1-5-589e4ebd9711@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move getting the scan_type to ad4030_conversion(). Previously, we were
getting the scan_type in two other places, then storing it in the
state struct before using it in ad4030_conversion(). This was a bit
fragile against potential future changes since it isn't obvious that
anything that could potentially change the scan_type would need to
also update the state struct. Also, the non-obviousness of this led to
a redundant call to iio_get_current_scan_type() in
ad4030_single_conversion() since it also calls ad4030_set_mode() which
in turn calls ad4030_conversion().
To simplify things, just call iio_get_current_scan_type() in
ad4030_conversion() where the returned struct is actually used and
don't bother storing it in the state struct.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250310-iio-adc-ad4030-check-scan-type-err-v1-4-589e4ebd9711@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move calling ad4030_set_mode() from the buffer preenable callback to
the update_scan_mode callback. This doesn't change any functionality
but is more logical since setting the mode is a function of the scan
mask and doesn't require an "undo" operation when the buffer is
disabled.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250310-iio-adc-ad4030-check-scan-type-err-v1-3-589e4ebd9711@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Check scan_type for error ad4030_get_chan_scale(). Currently, this
should never fail, but it is good practice to always check for errors
in case of future changes.
Calling iio_get_current_scan_type() is moved out of the if statement
also to avoid potential issues with future changes instead of assuming
that the non-differential case does not use extended scan_type.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/r/202503040954.n6MhjSsV-lkp@intel.com/
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250310-iio-adc-ad4030-check-scan-type-err-v1-1-589e4ebd9711@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add required bit shift to the event threshold read function to get
correct scaling.
When alert support was added, the write function correctly included the
required shift needed to convert the threshold register value to the
same scale as the raw ADC value. However, the shift got missed in the
read function.
Fixes: 27d1a4dbe1 ("iio: adc: ad7380: add alert support")
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Julien Stephan <jstephan@baylibre.com>
Link: https://patch.msgid.link/20250402-iio-adc-ad7380-fix-event-threshold-shift-v1-1-ad4975c296b2@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Check that the sw_mode_config function pointer is not NULL before
calling it. Not all buses define this callback, which resulted in a NULL
pointer dereference.
Fixes: e571c19021 ("iio: adc: ad7606: move scale_setup as function pointer on chip-info")
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250318-iio-adc-ad7606-improvements-v2-1-4b605427774c@baylibre.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move disabling of the SPI offload before attempting to use the SPI bus
to write a register in ad7380_offload_buffer_predisable().
This caused a crash in the spi_engine_irq() interrupt handler due to
being in an invalid state.
Fixes: bbeaec81a0 ("iio: ad7380: add support for SPI offload")
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Angelo Dureghello <adureghello@baylibre.com>
Link: https://patch.msgid.link/20250320-iio-adc-ad7380-fix-spi-offload-buffer-predisable-v1-1-6912ac8c0ae0@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
clock_set_rate should be executed after devm_clk_get_enabled.
Fixes: 97ad10bb29 ("iio: adc: rockchip_saradc: Make use of devm_clk_get_enabled")
Signed-off-by: Simon Xue <xxm@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20250312062016.137821-1-xxm@rock-chips.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Here is the big set of char, misc, iio, and other smaller driver
subsystems for 6.15-rc1. Lots of stuff in here, including:
- loads of IIO changes and driver updates
- counter driver updates
- w1 driver updates
- faux conversions for some drivers that were abusing the platform bus
interface
- coresight driver updates
- rust miscdevice binding updates based on real-world-use
- other minor driver updates
All of these have been in linux-next with no reported issues for quite a
while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZ+mNdQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylktACfYJix41jCCDbiFjnu7Hz4OIdcrUsAnRyF164M
1n5MhEhsEmvQj7WBwQLE
=AmmW
-----END PGP SIGNATURE-----
Merge tag 'char-misc-6.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc / IIO driver updates from Greg KH:
"Here is the big set of char, misc, iio, and other smaller driver
subsystems for 6.15-rc1. Lots of stuff in here, including:
- loads of IIO changes and driver updates
- counter driver updates
- w1 driver updates
- faux conversions for some drivers that were abusing the platform
bus interface
- coresight driver updates
- rust miscdevice binding updates based on real-world-use
- other minor driver updates
All of these have been in linux-next with no reported issues for quite
a while"
* tag 'char-misc-6.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (292 commits)
samples: rust_misc_device: fix markup in top-level docs
Coresight: Fix a NULL vs IS_ERR() bug in probe
misc: lis3lv02d: convert to use faux_device
tlclk: convert to use faux_device
regulator: dummy: convert to use the faux device interface
bus: mhi: host: Fix race between unprepare and queue_buf
coresight: configfs: Constify struct config_item_type
doc: iio: ad7380: describe offload support
iio: ad7380: add support for SPI offload
iio: light: Add check for array bounds in veml6075_read_int_time_ms
iio: adc: ti-ads7924 Drop unnecessary function parameters
staging: iio: ad9834: Use devm_regulator_get_enable()
staging: iio: ad9832: Use devm_regulator_get_enable()
iio: gyro: bmg160_spi: add of_match_table
dt-bindings: iio: adc: Add i.MX94 and i.MX95 support
iio: adc: ad7768-1: remove unnecessary locking
Documentation: ABI: add wideband filter type to sysfs-bus-iio
iio: adc: ad7768-1: set MOSI idle state to prevent accidental reset
iio: adc: ad7768-1: Fix conversion result sign
iio: adc: ad7124: Benefit of dev = indio_dev->dev.parent in ad7124_parse_channel_config()
...
Core changes:
- None really.
New drivers:
- AMD ISP411 "AMD ISP" driver.
- Exynos 2200 and 7870 SoC subdrivers.
- Sophgo RISC-V SG2042 and SG2044 subdrivers.
- Amlogic A4 subdriver.
- Rockchip RK3528 subdriver.
- Broadcom BCM21664 subdriver.
- Allwinner A523/T527 subdriver.
- Ingenic X1600 subdriver.
- Microchip SAMA7D65 subdriver, essentially a re-branded
Atmel AT91 PIO4 driver, but nowadays a Microschip SoC line.
Improvements:
- Bring in the devm_kmemdup_array() helper and use it throughout,
also bring in changes to other subsystems for this to establish
this helper.
- Support EGPIO on the Qualcomm SA8775P SoC.
- Extend EINT support in the Mediatek driver.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEElDRnuGcz/wPCXQWMQRCzN7AZXXMFAmfmehEACgkQQRCzN7AZ
XXMP7xAAislvKr11tILu/pJerSOI+OI6VcqJHa+u2AZbW/KuVpfMJNM5por5eXrX
sCKJh86zXd39fhC5znLFaESvrmCWdwjPu4HKfHA+BsPLOt3mEbM6XQUlxHJnnU8A
JrLDZFit7odPFxou9nApdd6QtM+Pqaaib4YSXFDrvULNyjoi0O6/NDuoOjunV4q9
C0S1yHSVOqO91qTZqpFE1PMVdNgzO7EmQ8UYQgGSPijl4NRS9CP7lFAxD9Z0VGhh
4Yjnlhr3ZSn3VklbGTBN8AcC8Yv69KSh2oYrue90PQwYI9yo3twIplqEIVFkDm39
27oLZoC+RLXNPTbrzSsdYwzti2Rg7mObJC7WMxyrl4wbu1ikzuBG8HjSj1Ai0Vmt
f4uchPA2w+L5hP0WLhujd7ocXrG2YNohjaduYZU/1y6Cvu2L7kF6+MK/fjlFWbVr
7JIKAR7ALvkpmPLQoUTsJxKLrwbvY5Q6Qh6plLdh6/L0rNQ1tLrJpklHhf3VzkCC
GuZSyC89Ym1smKO3XcfC+cmVUVheJQj0/NoY59RBkc0rDgApc6Uvs0icELBoDpLr
4XmghtMFdhTdUEs6n9Q4laEbHgYBAKrnN0BYWvaCmBxnZBZbUO44G7sbFOTMC+9l
wFs7MnH0f0YmzeF1LDz5z/oF8T3Xl0xMUL7qWoSu4zS1gjziJP8=
=iPMS
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v6.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"Core changes:
- None really.
New drivers:
- AMD ISP411 "AMD ISP" driver
- Exynos 2200 and 7870 SoC subdrivers
- Sophgo RISC-V SG2042 and SG2044 subdrivers
- Amlogic A4 subdriver
- Rockchip RK3528 subdriver
- Broadcom BCM21664 subdriver
- Allwinner A523/T527 subdriver
- Ingenic X1600 subdriver
- Microchip SAMA7D65 subdriver, essentially a re-branded Atmel AT91
PIO4 driver, but nowadays a Microschip SoC line
Improvements:
- Bring in the devm_kmemdup_array() helper and use it throughout,
also bring in changes to other subsystems for this to establish
this helper
- Support EGPIO on the Qualcomm SA8775P SoC
- Extend EINT support in the Mediatek driver"
* tag 'pinctrl-v6.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (101 commits)
pinctrl: mediatek: Add EINT support for multiple addresses
pinctrl: amlogic-a4: Drop surplus semicolon
pinctrl: nuvoton: Reduce use of OF-specific APIs
pinctrl: nuvoton: Convert to use struct group_desc
pinctrl: nuvoton: Make use of struct pinfunction and PINCTRL_PINFUNCTION()
pinctrl: nuvoton: Convert to use struct pingroup and PINCTRL_PINGROUP()
pinctrl: npcm8xx: Fix incorrect struct npcm8xx_pincfg assignment
pinctrl: tegra: Fix off by one in tegra_pinctrl_get_group()
pinctrl: PINCTRL_AMDISP should depend on DRM_AMD_ISP
pinctrl: qcom: sa8775p: Enable egpio function
dt-bindings: pinctrl: qcom: Add egpio function for sa8775p
pinctrl: qcom: tlmm-test: Validate irq_enable delivers edge irqs
pinctrl: qcom: Clear latched interrupt status when changing IRQ type
dt-bindings: pinctrl: airoha: Add missing gpio-ranges property
pinctrl: bcm281xx: Add missing assignment in bcm21664_pinctrl_lock_all()
pinctrl: amd: isp411: Fix IS_ERR() vs NULL check in probe()
dt-bindings: pinctrl: at91-pio4: add microchip,sama7d65-pinctrl
pinctrl: tegra: Set SFIO mode to Mux Register
pinctrl-tegra: Restore SFSEL bit when freeing pins
pinctrl: tegra: Add descriptions for SoC data fields
...
hrtimers are initialized with hrtimer_init() and a subsequent store to
the callback pointer. This turned out to be suboptimal for the upcoming
Rust integration and is obviously a silly implementation to begin with.
This cleanup replaces the hrtimer_init(T); T->function = cb; sequence
with hrtimer_setup(T, cb);
The conversion was done with Coccinelle and a few manual fixups.
Once the conversion has completely landed in mainline, hrtimer_init()
will be removed and the hrtimer::function becomes a private member.
-----BEGIN PGP SIGNATURE-----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=bYAX
-----END PGP SIGNATURE-----
Merge tag 'timers-cleanups-2025-03-23' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer cleanups from Thomas Gleixner:
"A treewide hrtimer timer cleanup
hrtimers are initialized with hrtimer_init() and a subsequent store to
the callback pointer. This turned out to be suboptimal for the
upcoming Rust integration and is obviously a silly implementation to
begin with.
This cleanup replaces the hrtimer_init(T); T->function = cb; sequence
with hrtimer_setup(T, cb);
The conversion was done with Coccinelle and a few manual fixups.
Once the conversion has completely landed in mainline, hrtimer_init()
will be removed and the hrtimer::function becomes a private member"
* tag 'timers-cleanups-2025-03-23' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (100 commits)
wifi: rt2x00: Switch to use hrtimer_update_function()
io_uring: Use helper function hrtimer_update_function()
serial: xilinx_uartps: Use helper function hrtimer_update_function()
ASoC: fsl: imx-pcm-fiq: Switch to use hrtimer_setup()
RDMA: Switch to use hrtimer_setup()
virtio: mem: Switch to use hrtimer_setup()
drm/vmwgfx: Switch to use hrtimer_setup()
drm/xe/oa: Switch to use hrtimer_setup()
drm/vkms: Switch to use hrtimer_setup()
drm/msm: Switch to use hrtimer_setup()
drm/i915/request: Switch to use hrtimer_setup()
drm/i915/uncore: Switch to use hrtimer_setup()
drm/i915/pmu: Switch to use hrtimer_setup()
drm/i915/perf: Switch to use hrtimer_setup()
drm/i915/gvt: Switch to use hrtimer_setup()
drm/i915/huc: Switch to use hrtimer_setup()
drm/amdgpu: Switch to use hrtimer_setup()
stm class: heartbeat: Switch to use hrtimer_setup()
i2c: Switch to use hrtimer_setup()
iio: Switch to use hrtimer_setup()
...
The usual mixture of new drivers, support in existing drivers for new
devices, a range of features and general subsystem cleanup.
Two merges of immutable branches in here:
* SPI offload support. Culmination of a long effort to bring the ability
to offload triggered sequences of SPI operations to specific hardware,
allow high datarate acquisition over an SPI bus (if you have the right
hardware / FPGA firmware)
* GPIO set-array-helper - enables code simplification.
New device support
==================
adi,ad3552r-hs:
- Add support for AD3541r and AD3542r via newly supported FPGA HDL.
adi,ad4030
- New driver supporting the AD4030, AD4630 AD4630-16, AD4640-24, AD4632-16,
AD4632-24 1 and 2 channel high precision SPI ADCs.
adi,ad4851
- New driver and backend support for the AD4851, AD4852, AD4853, AD4854,
AD4855, AD4846, AD4857, AD4858 and AD4858I high speed multichannel
simultaneous sampling ADCs.
adi,ad7191
- New driver for this 24-bit ADC for precision bridge applications,
adi,ad7380
- Add support for the adaq4381-4 which is a 14-bit version of the
already supported adaq4380-1
adi,adis16550
- New driver using the ADIS library (which needed extensions) for this
IMU.
brcm,apds9160
- New driver for this proximity and ambient light sensor.
dynaimage,al3000a
- New driver for this illuminance sensor.
mcube,mc3230
- Add support for the mc3510c accelerometer with a different scale to existing
supported parts (some rework preceded this)
nxp,imx93
- Add compatibles for imx94 and imx95 which are fully compatible with imx93.
rockchip,saradc
- Add support for the RK3528 ADC
- Add support for the RK3562 ADC
silab,si7210
- New driver to support this I2C Hall effect magnetic position sensor.
ti,ads7138
- New driver supporting the ADS7128 and AD7138 I2C ADCs.
Staging driver drop
===================
adi,adis16240
- Drop this impact sensor. Interesting part but complex hence never left
staging due to ABI challenges. No longer readily available so drop driver.
New features
============
Documentation
- A really nice overview document introduce ADC terminology and how
it maps to IIO.
core
- New description for FAULT events, used in the ad7173.
- filter_type ABI used in ad4130.
buffer-dmaengine
- Split DMA channel request from buffer allocation (for SPI offload)
- Add a new _with_handle setup variant. (for SPI offload)
adi,adf4371
- Add control of reference clock type and support for frequency doubling
where appropriate.
adi,ad4695
- Support SPI offload.
- Support oversampling control.
adi,ad5791
- Support SPI offload.
adi,ad7124
- Add channel calibration support.
adi,ad7380:
- Alert support (threshold interrupts)
- SPI offload support.
adi,ad7606
- Support writing registers when using backend enabling software control
of modes.
adi,ad7944
- Support SPI offload.
adi,ad9832
- Use devm_regulator_get_enable() to simplify code.
adi,ad9834
- Use devm_regulator_get_enable() to simplify code.
adi,adxl345
- Improve IRQ handling code.
- Add debug access to registers.
bosch,bmi270
- Add temperature channel support.
- Add data ready trigger.
google,cross_ec
- Add trace events.
mcube,mc3230
- Add mount matrix support
- Add an OF match table.
Cleanup and minor bug fixes
===========================
Tree wide:
- Stop using iio_device_claim_direct_scoped() and introduce sparse friendly
iio_device_claim/release_direct()
The conditional scoped cleanup has proved hard to deal with, requiring
workarounds for various compiler issues and in is rather non-intuitive
so abandon that experiment. One of the attractions of that approach was
that it made it much harder to have unbalanced claim/release bugs so
instead introduce a conditional-lock style boolean returning new pair
of functions. These are inline in the header and have __acquire and
__release calls allowing sparse to detect lack of balance. There are
occasional false positives but so far those have reflected complex code
paths that benefited from cleanup anyway.
The first set of driver conversions are in this pull request, more to
follow next cycle. Various related cleanup in drivers.
Removal of the _scoped code is completed and the definition removed.
- Use of str_enable_disable() and similar helpers.
- Don't set regmap cache to REGCACHE_NONE as that's the default anyway.
- Change some caches from RBTREE to MAPLE reflecting best practice.
- Use the new gpiod_multi_set_value_cansleep()
- Make sure to grab direct mode for some calibrations paths.
- Avoid using memcmp on structures when checking for matching channel configs.
Instead just match field by field.
dt-bindings:
- Fix up indentation inconsistencies.
gts-helper:
- Simplify building of available scale table.
adi,ad-sigma-delta
- Make sure to disable channel after calibration done.
- Add error handling in configuring channel during calibration.
adi,ad2s1201
- use a bitmap_write() rather than directly accessing underlying storage.
adi,ad3552r-hs
- Fix a wrong error message.
- Make sure to use instruction mode for configuration.
adi,ad4695
- Add a conversion to ensure exit from conversion mode.
- Use custom regmap to handle required sclk rate change.
- Fix an out of bounds array access
- Simplify oversampling ratio handling.
adi,ad4851
- Fix a sign bug.
adi,ad5791
- Fix wrong exported number of storage bits.
adi,ad7124
- Disable all channels at probe to avoid strange initial configurations.
adi,ad7173
- Rework to allow static const struct ad_sigma_delta without need
to make a copy.
adi,ad7623
- Drop a BSD license tag that the authors consider unnecessary.
adi,ad7768-1
- Fix channels sign description exposed to user space.
- Set MOSI idle state to avoid accidental device reset.
- Avoid some overkill locking.
adi,axi-dac
- Check if device interface is busy when enabling data stream.
- Add control of bus mode.
bosch,bmi270
- Move a struct definition to a c file as only used there.
vishay,veml6030
- Enable regmap cache to reduce bus traffic.
- Fix ABI bug around scale reporting.
vishay,vem6075
- Check array bounds to harden against broken hardware.
Various other minor tweaks and fixes not called out.
*
-----BEGIN PGP SIGNATURE-----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=4tID
-----END PGP SIGNATURE-----
Merge tag 'iio-for-6.15a' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next
Jonathan writes:
IIO: New device support, features and cleanup for the 6.15 cycle.
The usual mixture of new drivers, support in existing drivers for new
devices, a range of features and general subsystem cleanup.
Two merges of immutable branches in here:
* SPI offload support. Culmination of a long effort to bring the ability
to offload triggered sequences of SPI operations to specific hardware,
allow high datarate acquisition over an SPI bus (if you have the right
hardware / FPGA firmware)
* GPIO set-array-helper - enables code simplification.
New device support
==================
adi,ad3552r-hs:
- Add support for AD3541r and AD3542r via newly supported FPGA HDL.
adi,ad4030
- New driver supporting the AD4030, AD4630 AD4630-16, AD4640-24, AD4632-16,
AD4632-24 1 and 2 channel high precision SPI ADCs.
adi,ad4851
- New driver and backend support for the AD4851, AD4852, AD4853, AD4854,
AD4855, AD4846, AD4857, AD4858 and AD4858I high speed multichannel
simultaneous sampling ADCs.
adi,ad7191
- New driver for this 24-bit ADC for precision bridge applications,
adi,ad7380
- Add support for the adaq4381-4 which is a 14-bit version of the
already supported adaq4380-1
adi,adis16550
- New driver using the ADIS library (which needed extensions) for this
IMU.
brcm,apds9160
- New driver for this proximity and ambient light sensor.
dynaimage,al3000a
- New driver for this illuminance sensor.
mcube,mc3230
- Add support for the mc3510c accelerometer with a different scale to existing
supported parts (some rework preceded this)
nxp,imx93
- Add compatibles for imx94 and imx95 which are fully compatible with imx93.
rockchip,saradc
- Add support for the RK3528 ADC
- Add support for the RK3562 ADC
silab,si7210
- New driver to support this I2C Hall effect magnetic position sensor.
ti,ads7138
- New driver supporting the ADS7128 and AD7138 I2C ADCs.
Staging driver drop
===================
adi,adis16240
- Drop this impact sensor. Interesting part but complex hence never left
staging due to ABI challenges. No longer readily available so drop driver.
New features
============
Documentation
- A really nice overview document introduce ADC terminology and how
it maps to IIO.
core
- New description for FAULT events, used in the ad7173.
- filter_type ABI used in ad4130.
buffer-dmaengine
- Split DMA channel request from buffer allocation (for SPI offload)
- Add a new _with_handle setup variant. (for SPI offload)
adi,adf4371
- Add control of reference clock type and support for frequency doubling
where appropriate.
adi,ad4695
- Support SPI offload.
- Support oversampling control.
adi,ad5791
- Support SPI offload.
adi,ad7124
- Add channel calibration support.
adi,ad7380:
- Alert support (threshold interrupts)
- SPI offload support.
adi,ad7606
- Support writing registers when using backend enabling software control
of modes.
adi,ad7944
- Support SPI offload.
adi,ad9832
- Use devm_regulator_get_enable() to simplify code.
adi,ad9834
- Use devm_regulator_get_enable() to simplify code.
adi,adxl345
- Improve IRQ handling code.
- Add debug access to registers.
bosch,bmi270
- Add temperature channel support.
- Add data ready trigger.
google,cross_ec
- Add trace events.
mcube,mc3230
- Add mount matrix support
- Add an OF match table.
Cleanup and minor bug fixes
===========================
Tree wide:
- Stop using iio_device_claim_direct_scoped() and introduce sparse friendly
iio_device_claim/release_direct()
The conditional scoped cleanup has proved hard to deal with, requiring
workarounds for various compiler issues and in is rather non-intuitive
so abandon that experiment. One of the attractions of that approach was
that it made it much harder to have unbalanced claim/release bugs so
instead introduce a conditional-lock style boolean returning new pair
of functions. These are inline in the header and have __acquire and
__release calls allowing sparse to detect lack of balance. There are
occasional false positives but so far those have reflected complex code
paths that benefited from cleanup anyway.
The first set of driver conversions are in this pull request, more to
follow next cycle. Various related cleanup in drivers.
Removal of the _scoped code is completed and the definition removed.
- Use of str_enable_disable() and similar helpers.
- Don't set regmap cache to REGCACHE_NONE as that's the default anyway.
- Change some caches from RBTREE to MAPLE reflecting best practice.
- Use the new gpiod_multi_set_value_cansleep()
- Make sure to grab direct mode for some calibrations paths.
- Avoid using memcmp on structures when checking for matching channel configs.
Instead just match field by field.
dt-bindings:
- Fix up indentation inconsistencies.
gts-helper:
- Simplify building of available scale table.
adi,ad-sigma-delta
- Make sure to disable channel after calibration done.
- Add error handling in configuring channel during calibration.
adi,ad2s1201
- use a bitmap_write() rather than directly accessing underlying storage.
adi,ad3552r-hs
- Fix a wrong error message.
- Make sure to use instruction mode for configuration.
adi,ad4695
- Add a conversion to ensure exit from conversion mode.
- Use custom regmap to handle required sclk rate change.
- Fix an out of bounds array access
- Simplify oversampling ratio handling.
adi,ad4851
- Fix a sign bug.
adi,ad5791
- Fix wrong exported number of storage bits.
adi,ad7124
- Disable all channels at probe to avoid strange initial configurations.
adi,ad7173
- Rework to allow static const struct ad_sigma_delta without need
to make a copy.
adi,ad7623
- Drop a BSD license tag that the authors consider unnecessary.
adi,ad7768-1
- Fix channels sign description exposed to user space.
- Set MOSI idle state to avoid accidental device reset.
- Avoid some overkill locking.
adi,axi-dac
- Check if device interface is busy when enabling data stream.
- Add control of bus mode.
bosch,bmi270
- Move a struct definition to a c file as only used there.
vishay,veml6030
- Enable regmap cache to reduce bus traffic.
- Fix ABI bug around scale reporting.
vishay,vem6075
- Check array bounds to harden against broken hardware.
Various other minor tweaks and fixes not called out.
*
* tag 'iio-for-6.15a' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (223 commits)
doc: iio: ad7380: describe offload support
iio: ad7380: add support for SPI offload
iio: light: Add check for array bounds in veml6075_read_int_time_ms
iio: adc: ti-ads7924 Drop unnecessary function parameters
staging: iio: ad9834: Use devm_regulator_get_enable()
staging: iio: ad9832: Use devm_regulator_get_enable()
iio: gyro: bmg160_spi: add of_match_table
dt-bindings: iio: adc: Add i.MX94 and i.MX95 support
iio: adc: ad7768-1: remove unnecessary locking
Documentation: ABI: add wideband filter type to sysfs-bus-iio
iio: adc: ad7768-1: set MOSI idle state to prevent accidental reset
iio: adc: ad7768-1: Fix conversion result sign
iio: adc: ad7124: Benefit of dev = indio_dev->dev.parent in ad7124_parse_channel_config()
iio: adc: ad7124: Implement system calibration
iio: adc: ad7124: Implement internal calibration at probe time
iio: adc: ad_sigma_delta: Add error checking for ad_sigma_delta_set_channel()
iio: adc: ad4130: Adapt internal names to match official filter_type ABI
iio: adc: ad7173: Fix comparison of channel configs
iio: adc: ad7124: Fix comparison of channel configs
iio: adc: ad4130: Fix comparison of channel setups
...
Device pointer is the only variable which is used by the
ads7924_get_channels_config() and which is declared outside this
function. Still, the function gets the iio_device and i2c_client as
parameters. The sole caller of this function (probe) already has the
device pointer which it can directly pass to the function.
Simplify code by passing the device pointer directly as a parameter
instead of digging it from the iio_device's private data.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://patch.msgid.link/2bb4c61122eca2f3a35f6087e7d9815675013f66.1740993491.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The current locking is only preventing a triggered buffer Transfer and a
debugfs register access from happening at the same time. If a register
access happens during a buffered read, the action is doomed to fail anyway,
since we need to write a magic value to exit continuous read mode.
Remove locking from the trigger handler and use
iio_device_claim_direct() instead in the register access function.
Reviewed-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Jonathan Santos <Jonathan.Santos@analog.com>
Link: https://patch.msgid.link/d0450b7c5d8467e54913ef905f6147baa2b866b3.1741268122.git.Jonathan.Santos@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Datasheet recommends Setting the MOSI idle state to high in order to
prevent accidental reset of the device when SCLK is free running.
This happens when the controller clocks out a 1 followed by 63 zeros
while the CS is held low.
Check if SPI controller supports SPI_MOSI_IDLE_HIGH flag and set it.
Fixes: a5f8c7da3d ("iio: adc: Add AD7768-1 ADC basic support")
Signed-off-by: Jonathan Santos <Jonathan.Santos@analog.com>
Reviewed-by: Marcelo Schmitt <marcelo.schmitt@analog.com>
Link: https://patch.msgid.link/c2a2b0f3d54829079763a5511359a1fa80516cfb.1741268122.git.Jonathan.Santos@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ad7768-1 ADC output code is two's complement, meaning that the voltage
conversion result is a signed value.. Since the value is a 24 bit one,
stored in a 32 bit variable, the sign should be extended in order to get
the correct representation.
Also the channel description has been updated to signed representation,
to match the ADC specifications.
Fixes: a5f8c7da3d ("iio: adc: Add AD7768-1 ADC basic support")
Reviewed-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Marcelo Schmitt <marcelo.schmitt@analog.com>
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Signed-off-by: Jonathan Santos <Jonathan.Santos@analog.com>
Cc: <Stable@vger.kernel.org>
Link: https://patch.msgid.link/505994d3b71c2aa38ba714d909a68e021f12124c.1741268122.git.Jonathan.Santos@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since commit a6eaf02b82 ("iio: adc: ad7124: Switch from of specific to
fwnode based property handling") the function
ad7124_parse_channel_config() has a parameter `dev` that holds
the value `indio_dev->dev.parent`. Make use of that to shorten two code
lines.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/v7l2skqj65vbku3ebjsfndfj3atl6iqpodamios2do6q6kcagf@whmuir6fwede
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Allow triggering both zero-scale and full-scale calibration via sysfs in
the same way as it's done for ad7173.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/20250303114659.1672695-18-u.kleine-koenig@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use the calibration function provided by the ad_sigma_delta shim to
calibrate all channels at probe time.
For measurements with gain 1 (i.e. if CONFIG_x.PGA = 0) full-scale
calibrations are not supported and the reset default value of the GAIN
register is supposed to be used then.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/20250303114659.1672695-17-u.kleine-koenig@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
All other calls to ad_sigma_delta_set_channel() in ad_sigma_delta.c
check the return value afterwards. Do it for all calls.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/20250303114659.1672695-16-u.kleine-koenig@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Recently the interface to to select a filter was officially blessed to
use "filter_type". Adapt the naming of several functions accordingly to
make the new standard more present and so make the driver a better
template for other drivers. Apart from the comment update this is just
s/filter_mode/filter_type/.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/20250303114659.1672695-15-u.kleine-koenig@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Checking the binary representation of two structs (of the same type)
for equality doesn't have the same semantic as comparing all members for
equality. The former might find a difference where the latter doesn't in
the presence of padding or when ambiguous types like float or bool are
involved. (Floats typically have different representations for single
values, like -0.0 vs +0.0, or 0.5 * 2² vs 0.25 * 2³. The type bool has
at least 8 bits and the raw values 1 and 2 (probably) both evaluate to
true, but memcmp finds a difference.)
When searching for a channel that already has the configuration we need,
the comparison by member is the one that is needed.
Convert the comparison accordingly to compare the members one after
another. Also add a static_assert guard to (somewhat) ensure that when
struct ad7173_channel_config::config_props is expanded, the comparison
is adapted, too.
This issue is somewhat theoretic, but using memcmp() on a struct is a
bad pattern that is worth fixing.
Fixes: 76a1e6a428 ("iio: adc: ad7173: add AD7173 driver")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/20250303114659.1672695-14-u.kleine-koenig@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Checking the binary representation of two structs (of the same type)
for equality doesn't have the same semantic as comparing all members for
equality. The former might find a difference where the latter doesn't in
the presence of padding or when ambiguous types like float or bool are
involved. (Floats typically have different representations for single
values, like -0.0 vs +0.0, or 0.5 * 2² vs 0.25 * 2³. The type bool has
at least 8 bits and the raw values 1 and 2 (probably) both evaluate to
true, but memcmp finds a difference.)
When searching for a channel that already has the configuration we need,
the comparison by member is the one that is needed.
Convert the comparison accordingly to compare the members one after
another. Also add a static_assert guard to (somewhat) ensure that when
struct ad7124_channel_config::config_props is expanded, the comparison
is adapted, too.
This issue is somewhat theoretic, but using memcmp() on a struct is a
bad pattern that is worth fixing.
Fixes: 7b8d045e49 ("iio: adc: ad7124: allow more than 8 channels")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/20250303114659.1672695-13-u.kleine-koenig@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Checking the binary representation of two structs (of the same type)
for equality doesn't have the same semantic as comparing all members for
equality. The former might find a difference where the latter doesn't in
the presence of padding or when ambiguous types like float or bool are
involved. (Floats typically have different representations for single
values, like -0.0 vs +0.0, or 0.5 * 2² vs 0.25 * 2³. The type bool has
at least 8 bits and the raw values 1 and 2 (probably) both evaluate to
true, but memcmp finds a difference.)
When searching for a channel that already has the configuration we need,
the comparison by member is the one that is needed.
Convert the comparison accordingly to compare the members one after
another. Also add a static_assert guard to (somewhat) ensure that when
struct ad4130_setup_info is expanded, the comparison is adapted, too.
This issue is somewhat theoretic, but using memcmp() on a struct is a
bad pattern that is worth fixing.
Fixes: 62094060cf ("iio: adc: ad4130: add AD4130 driver")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/20250303114659.1672695-12-u.kleine-koenig@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The function ad_sd_calibrate() enables the channel to calibrate at
function entry but doesn't disable it on exit. This is problematic
because if two (or more) channels are calibrated in a row, the second
calibration isn't executed as intended as the first (still enabled)
channel is recalibrated and after the first irq (i.e. when the
calibration of the first channel completed) the calibration is aborted.
This currently affects ad7173 only, as the other drivers using
ad_sd_calibrate() never have more than one channel enabled at a time.
To fix this, disable the calibrated channel after calibration.
Fixes: 031bdc8aee ("iio: adc: ad7173: add calibration support")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/20250303114659.1672695-11-u.kleine-koenig@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
AD7191 is a pin-programmable, ultra-low noise 24-bit sigma-delta ADC
designed for precision bridge sensor measurements. It features two
differential analog input channels, selectable output rates,
programmable gain, internal temperature sensor and simultaneous
50Hz/60Hz rejection.
Signed-off-by: Alisa-Dariana Roman <alisa.roman@analog.com>
Reviewed-by: David Lechner<dlechner@baylibre.com>
Link: https://patch.msgid.link/20250228141327.262488-3-alisa.roman@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The intention here was obviously to return an error if devm_regmap_init()
fails, but the return statement was accidentally left out. This leads to
an error pointer dereference when we call:
ret = ad4030_detect_chip_info(st);
Add the return statement.
Fixes: ec25cf6f1e ("iio: adc: ad4030: add support for ad4632-16 and ad4632-24")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/cc67cee7-9c65-46d2-aae3-f860fc3cc461@stanley.mountain
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The Successive Approximation ADC (SARADC) in RK3528 uses the v2
controller and support:
- 10-bit resolution
- Up to 1MS/s sampling rate
- 4 single-ended input channels
- Current consumption: 0.5mA @ 1MS/s
Add support for the 4 channels of 10-bit resolution supported by SARADC
in RK3528.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20250227184058.2964204-3-jonas@kwiboo.se
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The "c" variable is used to store error codes from ad4851_find_opt()
so it has to be signed for the error handling to work. Change it
to type int.
Fixes: 6250803fe2 ("iio: adc: ad4851: add ad485x driver")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/f5e260e9-d7a8-4dae-b7ea-f1bbb1760e60@stanley.mountain
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
We already have a local variable that holds a pointer to
st->channels_cfg[chan->scan_index]. Use that to simplify the code.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Trevor Gamblin <tgamblin@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250218-iio-adc-ad4695-fix-out-of-bounds-array-access-v1-2-57fef8c7a3fd@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix some out of bounds array access of st->channels_cfg in the ad4695
driver. This array only has elements for voltage channels, but it was
also being accessed for the temperature channel in a few cases causing
reading past the end of the array.
In some cases, this was harmless because the value was read but not
used. However, the in_temp_sampling_frequency attribute shares code
with the in_voltageY_sampling_frequency attributes and was trying to
read the oversampling ratio from the st->channels_cfg array. This
resulted in a garbage value being used in the calculation and the
resulting in_temp_sampling_frequency value was incorrect.
To fix, make sure we always check that we are dealing with a voltage
channel before accessing the st->channels_cfg array and use an
oversampling ratio of 1 for the temperature channel (multiplicative
identity value) since that channel doesn't support oversampling.
Fixes: 67d63185db ("iio: adc: ad4695: add offload-based oversampling support")
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Trevor Gamblin <tgamblin@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250218-iio-adc-ad4695-fix-out-of-bounds-array-access-v1-1-57fef8c7a3fd@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Don't use of.h in order to include mod_devicetable.h. Use it directly as
there no direct dependency on OF.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250218-dev-axi-adc-fix-headers-v1-1-5ddc79221d8c@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Single patch for all the relatively simple cases.
These new functions allow sparse to find failures to release
direct mode reducing chances of bugs over the claim_direct_mode()
functions that are deprecated.
Cc: Olivier Moysan <olivier.moysan@foss.st.com>
Cc: Phil Reid <preid@electromag.com.au>
Reviewed-by: Mike Looijmans <mike.looijmans@topic.nl>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250217141630.897334-30-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
These new functions allow sparse to find failures to release
direct mode reducing chances of bugs over the claim_direct_mode()
functions that are deprecated.
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250217141630.897334-27-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Introduce __max11410_write_samp_freq() helper and use guard() to avoid
need for manual unlock of the mutex. This allows direct returns and
simplifies the resulting error handling.
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250217141630.897334-26-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
These new functions allow sparse to find failures to release
direct mode reducing chances of bugs over the claim_direct_mode()
functions that are deprecated.
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://patch.msgid.link/20250217141630.897334-25-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move iio_device_claim_direct_mode() into the read_raw() callback
and use guard() to release a mutex. This enables simpler error
handling via direct returns.
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://patch.msgid.link/20250217141630.897334-24-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
These new functions allow sparse to find failures to release
direct mode reducing chances of bugs over the claim_direct_mode()
functions that are deprecated.
Reviewed-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Link: https://patch.msgid.link/20250217141630.897334-23-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move iio_device_claim_direct_mode() up one layer in the call stack,
and use guard() for scope based unlocking to simplify error handling
by allowing direct returns.
Reviewed-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Link: https://patch.msgid.link/20250217141630.897334-22-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
These new functions allow sparse to find failures to release
direct mode reducing chances of bugs over the claim_direct_mode()
functions that are deprecated.
This is a complex function with a lot more than the release of direct
mode to unwind on error. As such no attempt made to factor out
the inner code.
Cc: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250217141630.897334-21-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
These new functions allow sparse to find failures to release
direct mode reducing chances of bugs over the claim_direct_mode()
functions that are deprecated.
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250217141630.897334-20-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
These new functions allow sparse to find failures to release
direct mode reducing chances of bugs over the claim_direct_mode()
functions that are deprecated.
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250217141630.897334-19-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Factor out everything under the direct mode claim allowing direct returns
in error paths. Switch sense of matching in the loop and use a continue
to reduce code indent and improve readability.
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250217141630.897334-18-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
These new functions allow sparse to find failures to release
direct mode reducing chances of bugs over the claim_direct_mode()
functions that are deprecated
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250217141630.897334-17-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Factor out everything under the direct mode claim allowing direct returns
in error paths.
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250217141630.897334-16-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
These new functions allow sparse to find failures to release
direct mode reducing chances of bugs over the claim_direct_mode()
functions that are deprecated.
This driver got partly converted during removal of the _scoped form.
However some more cases got added in parallel.
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250217141630.897334-15-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
These new functions allow sparse to find failures to release
direct mode reducing chances of bugs over the claim_direct_mode()
functions that are deprecated.
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250217141630.897334-14-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The data used is all in local variables so there is no advantage
in setting *val = ret with the direct mode claim held.
Move it later to after error check.
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250217141630.897334-13-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
These new functions allow sparse to find failures to release
direct mode reducing chances of bugs over the claim_direct_mode()
functions that are deprecated.
Cc: Alisa-Dariana Roman <alisa.roman@analog.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250217141630.897334-12-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Factor out everything under the lock, use guard() for the mutex to
avoid need to manually unlock, and switch sense of matching checks
in loops to reduce indent.
There are some functional changes in here as well as the code
no longer updates the filter_freq_available if no change has
been made to the oversampling ratio.
Cc: Alisa-Dariana Roman <alisa.roman@analog.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250217141630.897334-11-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
These new functions allow sparse to find failures to release
direct mode reducing chances of bugs over the claim_direct_mode()
functions that are deprecated.
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250217141630.897334-10-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
These new functions allow sparse to find failures to release
direct mode reducing chances of bugs over the claim_direct_mode()
functions that are deprecated.
Reviewed-by: Olivier Moysan <olivier.moysan@foss.st.com>
Link: https://patch.msgid.link/20250217141630.897334-9-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This allows the claim on direct mode to be release in one place
rather than a lot of error paths, simplifying code.
Reviewed-by: Olivier Moysan <olivier.moysan@foss.st.com>
Link: https://patch.msgid.link/20250217141630.897334-8-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Convert to use devm_kmemdup_array() and while at it, use source size
instead of destination.
Signed-off-by: Raag Jadav <raag.jadav@intel.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
hrtimer_setup() takes the callback function pointer as argument and
initializes the timer completely.
Replace hrtimer_init() and the open coded initialization of
hrtimer::function with the new setup mechanism.
Patch was created by using Coccinelle.
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Zack Rusin <zack.rusin@broadcom.com>
Link: https://lore.kernel.org/all/570792e31b28a94a511c19c6789f2171a6745685.1738746904.git.namcao@linutronix.de
Reduce verbosity by using gpiod_multi_set_value_cansleep() instead of
gpiod_set_array_value().
These are not called in an atomic context, so changing to the cansleep
variant is fine.
Also drop unnecessary braces while we are at it.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250210-gpio-set-array-helper-v3-7-d6a673674da8@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This complex cleanup.h use case of conditional guards has proved
to be more trouble that it is worth in terms of false positive compiler
warnings and hard to read code.
Move directly to the new claim/release_direct() that allow sparse
to check for unbalanced context.
Cc: João Paulo Gonçalves <joao.goncalves@toradex.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250209180624.701140-20-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This complex cleanup.h use case of conditional guards has proved
to be more trouble that it is worth in terms of false positive compiler
warnings and hard to read code.
Move directly to the new claim/release_direct() that allow sparse
to check for unbalanced context
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250209180624.701140-19-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This complex cleanup.h use case of conditional guards has proved
to be more trouble that it is worth in terms of false positive compiler
warnings and hard to read code.
Move directly to the new claim/release_direct() that allow sparse
to check for unbalanced context
Reviewed-by: ChiYuan Huang <cy_huang@richtek.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250209180624.701140-18-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This complex cleanup.h use case of conditional guards has proved
to be more trouble that it is worth in terms of false positive compiler
warnings and hard to read code.
Move directly to the new claim/release_direct() that allow sparse
to check for unbalanced context.
Reviewed-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250209180624.701140-17-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This complex cleanup.h use case of conditional guards has proved
to be more trouble that it is worth in terms of false positive compiler
warnings and hard to read code.
Move directly to the new claim/release_direct() that allow sparse
to check for unbalanced context. Also use guard() to simplify mutex
unlock paths.
Reviewed-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250209180624.701140-16-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This complex cleanup.h use case of conditional guards has proved
to be more trouble that it is worth in terms of false positive compiler
warnings and hard to read code.
Move directly to the new claim/release_direct() that allow sparse
to check for unbalanced context.
Cc: Ramona Alexandra Nechita <ramona.nechita@analog.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250209180624.701140-15-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This complex cleanup.h use case of conditional guards has proved
to be more trouble that it is worth in terms of false positive compiler
warnings and hard to read code.
Move directly to the new claim/release_direct() that allow sparse
to check for unbalanced context.
Reviewed-by: Trevor Gamblin <tgamblin@baylibre.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250209180624.701140-14-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This complex cleanup.h use case of conditional guards has proved
to be more trouble that it is worth in terms of false positive compiler
warnings and hard to read code.
Move directly to the new claim/release_direct() that allow sparse
to check for unbalanced context.
Cc: Guillaume Stols <gstols@baylibre.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250209180624.701140-13-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
