While adding interconnect support for the QCM2290 platform some of them
got the c&p error, rogue MASTER_APPSS_PROC for the config_noc
interconnect. Turn that into SLAVE_QUP_0 as expected.
Fixes: 5b970ff019 ("arm64: dts: qcom: qcm2290: Hook up interconnects")
Reported-by: Konrad Dybcio <konradybcio@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20250207-rb1-bt-v4-4-d810fc8c94a9@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Jens reported that the sanity checks added to the new ps883x USB retimer
driver breaks USB and display on the HP X14. Turns out the X14 only has
a retimer on one of the ports, but this initially went unnoticed due to
the missing sanity check (and error handling) in the retimer driver.
Drop the non-existing retimer from the devicetree to enable the second
USB port and the display subsystem.
Note that this also matches the ACPI tables.
Fixes: 6f18b8d414 ("arm64: dts: qcom: x1e80100-hp-x14: dt for HP Omnibook X Laptop 14")
Cc: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
Tested-by: Juerg Haefliger <juerg.haefliger@canonical.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20250328084154.16759-1-johan+linaro@kernel.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
On Lenovo ThinkPad T14s, the headset is connected via a HiFi mux to
support CTIA and OMTP headsets. This switch is used to minimise pop and
click during headset type switching.
Enable the mux controls required to power this switch along with wiring up
gpio that control the headset switching.
Without this, headset audio will be very noisy and might see headset
detection errors.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Christopher Obbard <christopher.obbard@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20250327100633.11530-7-srinivas.kandagatla@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Introduce a device tree for the HP EliteBook Ultra G1q 14" AI laptop. It
seems to be using the same baseboard as the HP OmniBook X 14 so just use
that for now.
Signed-off-by: Juerg Haefliger <juerg.haefliger@canonical.com>
Link: https://lore.kernel.org/r/20250429144957.2088284-4-juerg.haefliger@canonical.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Only two little a520s share the same L2, every a720 has their own L2
cache.
Fixes: d235037799 ("arm64: dts: qcom: add initial SM8650 dtsi")
Signed-off-by: Pengyu Luo <mitltlatltl@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250405105529.309711-1-mitltlatltl@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The Qualcomm X Elite Devkit has 2 USB-A ports, both connected to the USB
multiport controller, each one via a separate NXP PTN3222 eUSB2-to-USB2
redriver to the eUSB2 PHY for High-Speed support, with a dedicated QMP
PHY for SuperSpeed support.
Describe each redriver and then enable each pair of PHYs and the
USB controller itself, in order to enable support for the 2 USB-A ports.
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250324-x1e001de-devkit-dts-enable-usb-a-ports-v1-1-81153b2d1edf@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Commit d37e2646c8 ("arm64: dts: qcom: x1e80100-pmics: Enable all SMB2360
separately") disables all SMB2360s and let the board DTS explicitly enable
them. The HP OmniBook DTS is from before this change and is missing the
explicit enabling. Add that to get all USB root ports.
Fixes: 6f18b8d414 ("arm64: dts: qcom: x1e80100-hp-x14: dt for HP Omnibook X Laptop 14")
Cc: stable@vger.kernel.org # 6.14
Signed-off-by: Juerg Haefliger <juerg.haefliger@canonical.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20250319160509.1812805-1-juerg.haefliger@canonical.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Enable support for download mode to collect RAM dumps in case of a
system crash, allowing post mortem analysis.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250512-ipq5018-syscon-v1-2-eb1ad2414c3c@outlook.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add phy and controller nodes for a 2-lane Gen2 and
a 1-lane Gen2 PCIe bus. IPQ5018 has 8 MSI SPI interrupts and
one global interrupt.
NOTE: the PCIe controller supports gen3, yet the phy is limited to gen2.
Signed-off-by: Nitheesh Sekar <quic_nsekar@quicinc.com>
Signed-off-by: Sricharan R <quic_srichara@quicinc.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://lore.kernel.org/r/20250514-ipq5018-pcie-v10-1-5b42a8eff7ea@outlook.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
There is a typo in sm8350.dts where the node label
mmeory@85200000 should be memory@85200000.
This patch corrects the typo for clarity and consistency.
Fixes: b7e8f433a6 ("arm64: dts: qcom: Add basic devicetree support for SM8350 SoC")
Cc: stable@vger.kernel.org
Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com>
Link: https://lore.kernel.org/r/20250514114656.2307828-1-alok.a.tiwari@oracle.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Both ports seem to work, just like on other X1E laptops.
Tested with a Type-C-to-HDMI2.0 dock (translating into up to 2 DP lanes
worth of bandwidth).
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250514-topic-romu_dp-v1-1-6242d6acb5e5@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add the required nodes for sound playback via a connected external
display (DisplayPort over USB-C).
In user space just the following route needs to be set (e.g. using
ALSA UCM):
amixer -c0 cset name='DISPLAY_PORT_RX Audio Mixer MultiMedia1' 1
Afterwards one can play audio on the MultiMedia1 sound device, e.g.:
aplay -D plughw:0,0 test.wav
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Link: https://lore.kernel.org/r/20250507-fp5-dp-sound-v4-5-4098e918a29e@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Default pinctrl configurations for all QUP (Qualcomm Universal Peripheral)
Serial Engines (SEs) are missing in the SoC device tree. These
configurations are required by client teams when enabling any SEs as I2C,
SPI, or Serial protocols.
Add default pin configurations for Serial Engines (SEs) for all supported
protocols, including I2C, SPI, and UART, to the sa8775p device tree. This
change facilitates slave device driver clients to enable usecase with
minimal modifications.
Remove duplicate pin configurations from target-specific file as same pin
configuration is included in the SoC device tree.
Acked-by: Mukesh Kumar Savaliya <quic_msavaliy@quicinc.com>
Signed-off-by: Viken Dadhaniya <quic_vdadhani@quicinc.com>
Link: https://lore.kernel.org/r/20250509090443.4107378-1-quic_vdadhani@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add DT entries for the sm8550 iris decoder.
Since the firmware is required to be signed, only enable
on Qualcomm development boards where the firmware is
publicly distributed.
Signed-off-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250509-topic-sm8x50-upstream-iris-8550-dt-v4-1-22ced9179da3@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Enable the Focaltech FT8719 touchscreen controller used in the Poco F1
(EBBG) panel variant.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Joel Selvaraj <foss@joelselvaraj.com>
Link: https://lore.kernel.org/r/20250506-pocof1-touchscreen-support-v4-4-bfb53da52945@joelselvaraj.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Enable the Novatek NT36672A touchscreen controller used in the Poco F1
(Tianma) panel variant.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Joel Selvaraj <foss@joelselvaraj.com>
Link: https://lore.kernel.org/r/20250506-pocof1-touchscreen-support-v4-3-bfb53da52945@joelselvaraj.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Enable qupv3_id_1 and gpi_dma1 as they are required for configuring
touchscreen. Also add pinctrl configurations needed for touchscreen.
These are common for both the tianma and ebbg touchscreen variant.
In the subsequent patches, we will enable support for the Novatek NT36672a
touchscreen and FocalTech FT8719 touchscreen that are used in the Poco F1
Tianma and EBBG panel variant respectively. This is done in preparation
for that.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Joel Selvaraj <foss@joelselvaraj.com>
Link: https://lore.kernel.org/r/20250506-pocof1-touchscreen-support-v4-2-bfb53da52945@joelselvaraj.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Back when display support was added initially to CRD, and we used to have
two separate compatibles for eDP and DP, it was supposed to override the
DP compatible with the eDP one in the board specific devicetree. Since
then, the DP driver has been reworked to figure out the eDP/DP at runtime
while only DP compatible remained in the end.
Even though the override does nothing basically, drop it to avoid
further confusion. Drop it from all X Elite based platforms.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250509-x1e80100-dts-drop-useless-dp-compatible-override-v2-1-126db05cb70a@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add the nodes for the bimc, pcnoc, snoc and snoc_mm. And wire up the
interconnects where applicable.
Signed-off-by: Vladimir Lypak <vladimir.lypak@gmail.com>
[luca: Prepare patch for upstream submission]
Signed-off-by: Luca Weiss <luca@lucaweiss.eu>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250420-msm8953-interconnect-v2-2-828715dcb674@lucaweiss.eu
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add the node and pinctrl for uart_5 found on the MSM8953 SoC.
Signed-off-by: Felix Kaechele <felix@kaechele.ca>
[luca: Prepare patch for upstream submission]
Signed-off-by: Luca Weiss <luca@lucaweiss.eu>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250406-msm8953-uart_5-v1-1-7e4841674137@lucaweiss.eu
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use the MSM_FRONTEND_DAI_MULTIMEDIA* defines to make the code more
readable. No functional change intended.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250425-q6asmdai-defines-v1-11-28308e2ce7d4@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use the MSM_FRONTEND_DAI_MULTIMEDIA* defines to make the code more
readable. No functional change intended.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250425-q6asmdai-defines-v1-10-28308e2ce7d4@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use the MSM_FRONTEND_DAI_MULTIMEDIA* defines to make the code more
readable. No functional change intended.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250425-q6asmdai-defines-v1-9-28308e2ce7d4@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use the MSM_FRONTEND_DAI_MULTIMEDIA* defines to make the code more
readable. No functional change intended.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250425-q6asmdai-defines-v1-8-28308e2ce7d4@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use the MSM_FRONTEND_DAI_MULTIMEDIA* defines to make the code more
readable. No functional change intended.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250425-q6asmdai-defines-v1-7-28308e2ce7d4@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use the MSM_FRONTEND_DAI_MULTIMEDIA* defines to make the code more
readable. No functional change intended.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250425-q6asmdai-defines-v1-6-28308e2ce7d4@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use the MSM_FRONTEND_DAI_MULTIMEDIA* defines to make the code more
readable. No functional change intended.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250425-q6asmdai-defines-v1-5-28308e2ce7d4@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use the MSM_FRONTEND_DAI_MULTIMEDIA* defines to make the code more
readable. No functional change intended.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250425-q6asmdai-defines-v1-4-28308e2ce7d4@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use the MSM_FRONTEND_DAI_MULTIMEDIA* defines to make the code more
readable. No functional change intended.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250425-q6asmdai-defines-v1-3-28308e2ce7d4@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use the MSM_FRONTEND_DAI_MULTIMEDIA* defines to make the code more
readable. No functional change intended.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250425-q6asmdai-defines-v1-2-28308e2ce7d4@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use the MSM_FRONTEND_DAI_MULTIMEDIA* defines to make the code more
readable. No functional change intended.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250425-q6asmdai-defines-v1-1-28308e2ce7d4@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Extend the USB graph to connect the OCP96011 switch, the PTN36502
redriver, the USB controllers and the MDSS, so that DisplayPort over
USB-C is working.
Connect some parts of the graph directly in the SoC dtsi since those
parts are wired up like this in the SoC directly.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250425-fp5-pmic-glink-dp-v3-4-cc9c2aeb42fb@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add a node for the OCP96011 on the board which is used to handle USB-C
analog audio switch and handles the SBU mux for DisplayPort-over-USB-C.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Link: https://lore.kernel.org/r/20250425-fp5-pmic-glink-dp-v3-3-cc9c2aeb42fb@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add a node for the "Type-C USB 3.1 Gen 1 and DisplayPort v1.2 combo
redriver" found on this device.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Link: https://lore.kernel.org/r/20250425-fp5-pmic-glink-dp-v3-2-cc9c2aeb42fb@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
While in the past the 'reg' properties were often written using decimal
'0' for #address-cells = <2> & #size-cells = <2>, nowadays the style is
to use hexadecimal '0x0' instead.
Align this dtsi file to the new style to make it consistent, and don't
use mixed 0x0 and 0 anymore.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250324-sm6350-videocc-v2-1-cc22386433f4@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
There's devices that don't have a DMIC connected to va-macro, so stop
setting the pinctrl in sc7280.dtsi, but move it to the devices that
actually are using it.
No change in functionality is expected, just some boards with disabled
va-macro are losing the pinctrl (herobrine-r1, villager-r0, zombie*).
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250404-sc7280-va-dmic01-v1-1-2862ddd20c48@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Now that we have ACD support for GPU, add additional OPPs up to
Turbo L3 which are supported across all existing SKUs.
Signed-off-by: Akhil P Oommen <quic_akhilpo@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Tested-by: Maya Matuszczyk <maccraft123mc@gmail.com>
Tested-by: Anthony Ruhier <aruhier@mailbox.org>
Acked-by: Bjorn Andersson <andersson@kernel.org>
Patchwork: https://patchwork.freedesktop.org/patch/649354/
Signed-off-by: Rob Clark <robdclark@chromium.org>
Update GPU node to include acd level values.
Signed-off-by: Akhil P Oommen <quic_akhilpo@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Tested-by: Maya Matuszczyk <maccraft123mc@gmail.com>
Tested-by: Anthony Ruhier <aruhier@mailbox.org>
Acked-by: Bjorn Andersson <andersson@kernel.org>
Patchwork: https://patchwork.freedesktop.org/patch/649352/
Signed-off-by: Rob Clark <robdclark@chromium.org>
Remove the generic UART pinctrl templates from msm8939.dtsi and copy the
definition for the custom UART use cases into the board DT files. This
makes it clear that the set of pins/pull etc are specific to the board and
UART use case.
No functional change.
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Link: https://lore.kernel.org/r/20250422-msm8916-console-pinctrl-v2-6-f345b7a53c91@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Remove the generic UART pinctrl templates from msm8916.dtsi and copy the
definition for the custom UART use cases into the board DT files. This
makes it clear that the set of pins/pull etc are specific to the board and
UART use case.
No functional change.
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Link: https://lore.kernel.org/r/20250422-msm8916-console-pinctrl-v2-5-f345b7a53c91@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The Motorola MSM8916-based smartphones all use UART1 with 2 pins (TX, RX)
as debug UART console, so make use of the new &blsp_uart1_console_default
template. This applies the needed bias-pull-up to avoid garbage input,
bootph-all for U-Boot and avoids having to override the UART pins.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Link: https://lore.kernel.org/r/20250422-msm8916-console-pinctrl-v2-4-f345b7a53c91@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Convert the majority of MSM8916/39-based boards, which use UART2 with 2
pins (TX, RX) for the debug UART console. This adds the needed bias-pull-up
and bootph-all properties to avoid garbage input when UART is disconnected.
apq8016-schneider-hmibsc.dts does not use UART2 as a debug console, so it's
left as-is in this commit.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Link: https://lore.kernel.org/r/20250422-msm8916-console-pinctrl-v2-3-f345b7a53c91@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
At the moment, msm8916/39.dtsi have two inconsistent UART pinctrl templates
that are used by all the boards:
- &blsp_uart1_default configures all 4 pins (TX, RX, CTS, RTS), some
boards then limit this to just RX and TX
- &blsp_uart2_default only configures 2 pins (TX, RX), even though UART2
also supports CTS/RTS
It's difficult to define a generic pinctrl template for all UART use cases,
since they are quite different in practice. The main use case for most of
the 40+ MSM8916/39-based boards upstream is the UART debug console. The
current generic template is lacking some properties to work properly:
- bias-pull-up for RX: Generally, UART is push-pull and does not need pull
up/down. Both sides drive TX, so RX should never be floating. This is
why the current pinctrl in msm8916/39.dtsi uses bias-disable. However,
this assumes that UART is always connected. For the debug console this
will be rarely the case on mobile devices, only during debugging
sessions. The rest of the time, the RX pin is floating.
This has never caused massive problems, but it's obvious now that this
needs fixing:
(1) In U-Boot, we have been fighting with problems with autoboot for
years. Most of the time, there is a single \0 byte ("break event")
read during boot, which interrupts the autoboot process. I tried to
work around that by inserting some random delay [1], but it turned
out this is also not working reliably on all boards.
What happens is: Since RX is floating, it switches randomly between
high or low. A long low state is interpreted as "break event" (\0).
(2) In postmarketOS, we used to have the "magic SysRq key" enabled by
default for the serial console. We had to disable this at some
point, because there was a small number of users who were reporting
sysrq spam in the kernel log, possibly even crashes/panics
triggered by sysrq.
What likely happened is: SysRq is triggered by sending a "break
event", like in (1). With enough luck, you could even trigger any
of the SysRq actions if the RX pin switches between high and low
(e.g. because of noise introduced by the LTE radio close by).
We can fix this using bias-pull-up, but this may be unneeded,
unexpected, or even unwanted for other UART use cases.
- bootph-all: U-Boot needs to know which pinctrl to apply during early
boot stages, so we should specify "bootph-all" for the console UART
pinctrl. Without bootph-all, the bias-pull-up won't be applied early
enough in U-Boot to avoid the problem with autoboot in point (1) above.
It doesn't make sense to specify this for the other UART instances.
bootph-all is a generic property documented in dt-schema bootph.yaml.
Define these two additional properties only for the debug UART console, by
defining a new pinctrl template specifically for that. In the following
commits, boards will be converted to use these where appropriate.
[1]: ad7e967738
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Link: https://lore.kernel.org/r/20250422-msm8916-console-pinctrl-v2-2-f345b7a53c91@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
In preparation of adding a new console UART specific pinctrl template, move
the pinctrl reference to the board DT part. This forces people porting new
boards to consider what exactly they need for their board.
No functional change for the boards upstream.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Link: https://lore.kernel.org/r/20250422-msm8916-console-pinctrl-v2-1-f345b7a53c91@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
WoA devices using x1e/x1p use android firmware to boot, which notably
includes Gunyah hypervisor. This means that, so far, Linux-based OS
could only boot in EL1 on those devices.
However Windows can replace Gunyah upon boot with it's own hypervisor,
and with the use of tools such as "slbounce", it's possible to do the
same for Linux-based OS, in which case some modifications to the DT are
necessary to facilitate the absence of Gunyah services.
Add a EL2-specific DT overlay and apply it to x1e/x1p WoA devices to
create -el2.dtb for each of them alongside "normal" dtb.
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Link: https://lore.kernel.org/r/20250503-sc-el2-overlays-v2-5-24e9b4572e15@trvn.ru
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
x1e80100 has an SMMUv3 connected to PCIe which is normally controlled by
Gunyah and is thus transparent to the OS. However if we boot Linux in
EL2, without Gunyah, we need to manage this IOMMU ourselves. To make
that easier, and since the hardware actually exists, just not "usually"
managed by Linux, describe it in the dts as "reserved".
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Link: https://lore.kernel.org/r/20250503-sc-el2-overlays-v2-4-24e9b4572e15@trvn.ru
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
WoA devices using sc8280xp use android firmware to boot, which notably
includes QHEE hypervisor. This means that, so far, Linux-based OS could
only boot in EL1 on those devices.
However Windows can replace QHEE upon boot with it's own hypervisor, and
with the use of tools such as "slbounce", it's possible to do the same
for Linux-based OS, in which case some modifications to the DT are
necessary to facilitate the absence of QHEE services.
Add a EL2-specific DT overlay and apply it to sc8280xp WoA devices to
create -el2.dtb for each of them alongside "normal" dtb.
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Link: https://lore.kernel.org/r/20250503-sc-el2-overlays-v2-3-24e9b4572e15@trvn.ru
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
sc8280xp has an SMMUv3 connected to PCIe which is normally controlled by
QHEE and is thus transparent to the OS. However if we boot Linux in EL2,
without QHEE, we need to manage this IOMMU ourselves. To make that
easier, and since the hardware actually exists, just not "usually"
managed by Linux, describe it in the dts as "reserved".
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Link: https://lore.kernel.org/r/20250503-sc-el2-overlays-v2-2-24e9b4572e15@trvn.ru
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
WoA devices using sc7180 use android firmware to boot, which notably
includes QHEE hypervisor. This means that, so far, Linux-based OS could
only boot in EL1 on those devices.
However Windows can replace QHEE upon boot with it's own hypervisor, and
with the use of tools such as "slbounce", it's possible to do the same
for Linux-based OS, in which case some modifications to the DT are
necessary to facilitate the absence of QHEE services.
Add a EL2-specific DT overlay and apply it to sc7180 WoA devices to
create -el2.dtb for each of them alongside "normal" dtb.
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Link: https://lore.kernel.org/r/20250503-sc-el2-overlays-v2-1-24e9b4572e15@trvn.ru
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Describe the missing power source, bias and direction for each of the USB0
retimer gpio-controlled voltage regulators related pin configuration.
Fixes: 019e1ee32f ("arm64: dts: qcom: x1e001de-devkit: Enable external DP support")
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20250422-x1e001de-devkit-dts-fix-retimer-gpios-v2-2-0129c4f2b6d7@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Currently, on the X Elite Devkit, the pin configuration of the reset
gpios for all three PS8830 USB retimers are left configured by the
bootloader.
Fix that by describing their pin configuration.
Fixes: 019e1ee32f ("arm64: dts: qcom: x1e001de-devkit: Enable external DP support")
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20250422-x1e001de-devkit-dts-fix-retimer-gpios-v2-1-0129c4f2b6d7@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
In the ACPI DSDT table, PPP_RESOURCE_ID_LDO2_J is configured with 1256000
uV instead of the 1200000 uV we have currently in the device tree. Use the
same for consistency and correctness.
Cc: stable@vger.kernel.org
Fixes: af16b00578 ("arm64: dts: qcom: Add base X1E80100 dtsi and the QCP dts")
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250423-x1e-vreg-l2j-voltage-v1-6-24b6a2043025@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
In the ACPI DSDT table, PPP_RESOURCE_ID_LDO2_J is configured with 1256000
uV instead of the 1200000 uV we have currently in the device tree. Use the
same for consistency and correctness.
Cc: stable@vger.kernel.org
Fixes: 45247fe17d ("arm64: dts: qcom: x1e80100: add Lenovo Thinkpad Yoga slim 7x devicetree")
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250423-x1e-vreg-l2j-voltage-v1-5-24b6a2043025@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
In the ACPI DSDT table, PPP_RESOURCE_ID_LDO2_J is configured with 1256000
uV instead of the 1200000 uV we have currently in the device tree. Use the
same for consistency and correctness.
Cc: stable@vger.kernel.org
Fixes: 6f18b8d414 ("arm64: dts: qcom: x1e80100-hp-x14: dt for HP Omnibook X Laptop 14")
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250423-x1e-vreg-l2j-voltage-v1-4-24b6a2043025@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
In the ACPI DSDT table, PPP_RESOURCE_ID_LDO2_J is configured with 1256000
uV instead of the 1200000 uV we have currently in the device tree. Use the
same for consistency and correctness.
Cc: stable@vger.kernel.org
Fixes: d0e2f8f62d ("arm64: dts: qcom: Add device tree for ASUS Vivobook S 15")
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250423-x1e-vreg-l2j-voltage-v1-3-24b6a2043025@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
In the ACPI DSDT table, PPP_RESOURCE_ID_LDO2_J is configured with 1256000
uV instead of the 1200000 uV we have currently in the device tree. Use the
same for consistency and correctness.
Cc: stable@vger.kernel.org
Fixes: 7b8a31e82b ("arm64: dts: qcom: Add X1E001DE Snapdragon Devkit for Windows")
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250423-x1e-vreg-l2j-voltage-v1-2-24b6a2043025@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
In the ACPI DSDT table, PPP_RESOURCE_ID_LDO2_J is configured with 1256000
uV instead of the 1200000 uV we have currently in the device tree. Use the
same for consistency and correctness.
Cc: stable@vger.kernel.org
Fixes: bd50b1f5b6 ("arm64: dts: qcom: x1e80100: Add Compute Reference Device")
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250423-x1e-vreg-l2j-voltage-v1-1-24b6a2043025@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Replace the deprecated freq-table-hz property with an operating
points table with all supported frequencies and power levels.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250424-topic-sc7280-upstream-ufs-opps-v1-1-e63494d65f45@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Similarly to MSM8998, add and use modem metadata memory region.
This does not seemingly affect device functionality. But it fixes
DTBs check warning:
remoteproc@4080000: memory-region: [[45], [46]] is too short
Signed-off-by: Alexey Minnekhanov <alexeymin@postmarketos.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250504115120.1432282-2-alexeymin@postmarketos.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Since commit b5af64fceb ("soc: qcom: smem: Support reserved-memory
description") the SMEM device can be instantiated directly from a
reserved-memory node.
The 'smem' node is defined in this way for each modern IPQ SoCs except for
IPQ6018. In order to make it inline with the others, move the 'compatible'
and the 'hwlock' properties into the respective reserved-memory node, and
drop the standalone 'smem' node.
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Reviewed-by: Kathiravan Thirumoorthy <kathiravan.thirumoorthy@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250506-ipq6018-drop-smem-v1-1-af99d177be2f@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
During device mode initialization on certain QC targets, before the
runstop bit is set, sometimes it's observed that the GEVNTADR{LO/HI}
register write fails. As a result, GEVTADDR registers are still 0x0.
Upon setting runstop bit, DWC3 controller attempts to write the new
events to address 0x0, causing an SMMU fault and system crash.
This was initially observed on SM8450 and later reported on few
other targets as well. As suggested by Qualcomm HW team, clearing
the GUSB3PIPECTL.SUSPHY bit resolves the issue by preventing register
write failures. Address this by setting the snps,dis_u3_susphy_quirk
to keep the GUSB3PIPECTL.SUSPHY bit cleared. This change was tested
on multiple targets (SM8350, SM8450 QCS615 etc.) for over an year
and hasn't exhibited any side effects.
Signed-off-by: Pratham Pratap <quic_ppratap@quicinc.com>
Signed-off-by: Prashanth K <prashanth.k@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250325123019.597976-6-prashanth.k@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
During device mode initialization on certain QC targets, before the
runstop bit is set, sometimes it's observed that the GEVNTADR{LO/HI}
register write fails. As a result, GEVTADDR registers are still 0x0.
Upon setting runstop bit, DWC3 controller attempts to write the new
events to address 0x0, causing an SMMU fault and system crash.
This was initially observed on SM8450 and later reported on few
other targets as well. As suggested by Qualcomm HW team, clearing
the GUSB3PIPECTL.SUSPHY bit resolves the issue by preventing register
write failures. Address this by setting the snps,dis_u3_susphy_quirk
to keep the GUSB3PIPECTL.SUSPHY bit cleared. This change was tested
on multiple targets (SM8350, SM8450 QCS615 etc.) for over an year
and hasn't exhibited any side effects.
Signed-off-by: Pratham Pratap <quic_ppratap@quicinc.com>
Signed-off-by: Prashanth K <prashanth.k@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250325123019.597976-5-prashanth.k@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
During device mode initialization on certain QC targets, before the
runstop bit is set, sometimes it's observed that the GEVNTADR{LO/HI}
register write fails. As a result, GEVTADDR registers are still 0x0.
Upon setting runstop bit, DWC3 controller attempts to write the new
events to address 0x0, causing an SMMU fault and system crash.
This was initially observed on SM8450 and later reported on few
other targets as well. As suggested by Qualcomm HW team, clearing
the GUSB3PIPECTL.SUSPHY bit resolves the issue by preventing register
write failures. Address this by setting the snps,dis_u3_susphy_quirk
to keep the GUSB3PIPECTL.SUSPHY bit cleared. This change was tested
on multiple targets (SM8350, SM8450 QCS615 etc.) for over an year
and hasn't exhibited any side effects.
Signed-off-by: Prashanth K <prashanth.k@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250325123019.597976-4-prashanth.k@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
During device mode initialization on certain QC targets, before the
runstop bit is set, sometimes it's observed that the GEVNTADR{LO/HI}
register write fails. As a result, GEVTADDR registers are still 0x0.
Upon setting runstop bit, DWC3 controller attempts to write the new
events to address 0x0, causing an SMMU fault and system crash.
This was initially observed on SM8450 and later reported on few
other targets as well. As suggested by Qualcomm HW team, clearing
the GUSB3PIPECTL.SUSPHY bit resolves the issue by preventing register
write failures. Address this by setting the snps,dis_u3_susphy_quirk
to keep the GUSB3PIPECTL.SUSPHY bit cleared. This change was tested
on multiple targets (SM8350, SM8450 QCS615 etc.) for over an year
and hasn't exhibited any side effects.
Signed-off-by: Prashanth K <prashanth.k@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250325123019.597976-3-prashanth.k@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
During device mode initialization on certain QC targets, before the
runstop bit is set, sometimes it's observed that the GEVNTADR{LO/HI}
register write fails. As a result, GEVTADDR registers are still 0x0.
Upon setting runstop bit, DWC3 controller attempts to write the new
events to address 0x0, causing an SMMU fault and system crash.
This was initially observed on SM8450 and later reported on few
other targets as well. As suggested by Qualcomm HW team, clearing
the GUSB3PIPECTL.SUSPHY bit resolves the issue by preventing register
write failures. Address this by setting the snps,dis_u3_susphy_quirk
to keep the GUSB3PIPECTL.SUSPHY bit cleared. This change was tested
on multiple targets (SM8350, SM8450 QCS615 etc.) for over an year
and hasn't exhibited any side effects.
Signed-off-by: Prashanth K <prashanth.k@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250325123019.597976-2-prashanth.k@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Remove the invalid bt-en-sleep node. Not sure how it came into existence
but it seems the functionality is covered by the wcn-wlan-bt-en-state node:
wcn_wlan_bt_en: wcn-wlan-bt-en-state {
pins = "gpio116", "gpio117";
function = "gpio";
drive-strength = <2>;
bias-disable;
};
This fixes the following warning:
arch/arm64/boot/dts/qcom/x1e80100-hp-omnibook-x14.dtb: pinctrl@f100000: Unevaluated properties are not allowed ('bt-en-sleep' was unexpected)
from schema $id: http://devicetree.org/schemas/pinctrl/qcom,x1e80100-tlmm.yaml#
Signed-off-by: Juerg Haefliger <juerg.haefliger@canonical.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250416-fix-omnibook-dts-v1-1-2409220a7c6f@canonical.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add the camera subsystem and CCI used to interface with cameras on the
Snapdragon 670.
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250205035013.206890-8-mailingradian@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add nodes for the MPSS and its SMP2P. These are compatible with earlier
SM8650 with difference in lack of fifth memory region for Qlink Logging.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250221-b4-sm8750-modem-v3-1-462dae7303c7@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Update the lpassaudio node to support the new compatible as the
lpassaudio needs to support the reset functionality on the
QCS6490 RB3Gen2 board and the rest of the Audio functionality would be
provided from the LPASS firmware.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Taniya Das <quic_tdas@quicinc.com>
Link: https://lore.kernel.org/r/20250221-lpass_qcm6490_resets-v5-4-6be0c0949a83@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Update the lpassaudio node to support the new compatible as the
lpassaudio needs to support the reset functionality on the
QCM6490 IDP board and the rest of the Audio functionality would be
provided from the LPASS firmware.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Taniya Das <quic_tdas@quicinc.com>
Link: https://lore.kernel.org/r/20250221-lpass_qcm6490_resets-v5-3-6be0c0949a83@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use allocated region size for VBIF regions as defined by the docs
(0x3000) instead of just using the last register address.
Suggested-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250415-drm-msm-dts-fixes-v1-20-90cd91bdd138@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use allocated region size for VBIF regions as defined by the docs
(0x3000) instead of just using the last register address.
Suggested-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250415-drm-msm-dts-fixes-v1-19-90cd91bdd138@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use allocated region size for VBIF regions as defined by the docs
(0x3000) instead of just using the last register address.
Suggested-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250415-drm-msm-dts-fixes-v1-18-90cd91bdd138@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use allocated region size for VBIF regions as defined by the docs
(0x3000) instead of just using the last register address.
Suggested-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250415-drm-msm-dts-fixes-v1-17-90cd91bdd138@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use allocated region size for VBIF regions as defined by the docs
(0x3000) instead of just using the last register address.
Suggested-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250415-drm-msm-dts-fixes-v1-16-90cd91bdd138@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use allocated region size for VBIF regions as defined by the docs
(0x3000) instead of just using the last register address.
Suggested-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250415-drm-msm-dts-fixes-v1-15-90cd91bdd138@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use allocated region size for VBIF regions as defined by the docs
(0x3000) instead of just using the last register address.
Suggested-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250415-drm-msm-dts-fixes-v1-14-90cd91bdd138@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use allocated region size for VBIF regions as defined by the docs
(0x3000) instead of just using the last register address.
Suggested-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250415-drm-msm-dts-fixes-v1-13-90cd91bdd138@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use allocated region size for VBIF regions as defined by the docs
(0x3000) instead of just using the last register address.
Suggested-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250415-drm-msm-dts-fixes-v1-12-90cd91bdd138@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use allocated region size for VBIF regions as defined by the docs
(0x3000) instead of just using the last register address.
Suggested-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250415-drm-msm-dts-fixes-v1-11-90cd91bdd138@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use allocated region size for VBIF regions as defined by the docs
(0x3000) instead of just using the last register address.
Suggested-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250415-drm-msm-dts-fixes-v1-10-90cd91bdd138@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use allocated region size for VBIF regions as defined by the docs
(0x3000) instead of just using the last register address.
Suggested-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250415-drm-msm-dts-fixes-v1-9-90cd91bdd138@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use allocated region size for VBIF regions as defined by the docs
(0x3000) instead of just using the last register address.
Suggested-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250415-drm-msm-dts-fixes-v1-8-90cd91bdd138@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use allocated region size for VBIF regions as defined by the docs
(0x3000) instead of just using the last register address.
Suggested-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250415-drm-msm-dts-fixes-v1-7-90cd91bdd138@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use allocated region size for VBIF regions as defined by the docs
(0x3000) instead of just using the last register address.
Suggested-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250415-drm-msm-dts-fixes-v1-6-90cd91bdd138@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use allocated region size for VBIF regions as defined by the docs
(0x3000) instead of just using the last register address.
Suggested-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250415-drm-msm-dts-fixes-v1-5-90cd91bdd138@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use allocated region size for VBIF regions as defined by the docs
(0x3000) instead of just using the last register address.
Suggested-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250415-drm-msm-dts-fixes-v1-4-90cd91bdd138@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use allocated region size for VBIF regions as defined by the docs
(0x3000) instead of just using the last register address.
Suggested-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250415-drm-msm-dts-fixes-v1-3-90cd91bdd138@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Change the tag for MDP interconnects to QCOM_ICC_TAG_ALWAYS, so that if
CPUSS collapses, the display may stay on.
Suggested-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250415-drm-msm-dts-fixes-v1-2-90cd91bdd138@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
During initial porting these cd-gpios were missed. Having card detect is
beneficial because driver does not need to do polling every second and it
can just use IRQ. SD card detection in U-Boot is also fixed by this.
Fixes: cf85e9aee2 ("arm64: dts: qcom: sdm660-xiaomi-lavender: Add eMMC and SD")
Signed-off-by: Alexey Minnekhanov <alexeymin@postmarketos.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250415130101.1429281-1-alexeymin@postmarketos.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The "spin-table" enable-method requires "cpu-release-addr" property,
so add a dummy entry. It is assumed the bootloader will fill in the
correct values.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Acked-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250410-dt-cpu-schema-v2-6-63d7dc9ddd0a@kernel.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The "spin-table" enable-method requires "cpu-release-addr" property,
so add a dummy entry. It is assumed the bootloader will fill in the
correct values.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Acked-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250410-dt-cpu-schema-v2-5-63d7dc9ddd0a@kernel.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The correct property name is 'qcom,freq-domain', not
'qcom,freq-domains'.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250410-dt-cpu-schema-v2-4-63d7dc9ddd0a@kernel.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Since commit 6fd8d2d275 ("ASoC: qcom: qdsp6: Move frontend AIFs to
q6asm-dai") from over 4 years ago the audio routes beween MM_DL* +
MultiMedia* Playback and MultiMedia* Capture + MM_UL* are not necessary
anymore and can be removed from the dts files. It also helps to stop
anyone copying these into new dts files.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Reviewed-by: Srinivas Kandagatla <srini@kernel.org>
Link: https://lore.kernel.org/r/20250411-cleanup-mm-routes-v1-1-ba98f653aa69@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Particular device comes without headset combo jack, hence does not
feature wcd codec IC. In such cases, DMICs are powered from vreg_l1b.
Describe all 4 microphones in the audio routing. vdd-micb is defined
for lpass-macro already.
Signed-off-by: Aleksandrs Vinarskis <alex.vinarskis@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250412124956.20562-1-alex.vinarskis@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The RGMII interface is designed for speeds up to 1G. Phylink already
imposes the design limits for MII interfaces, and additional
specification is unnecessary. Therefore, we can remove this property
without any effect.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/E1u3bkm-000Epw-QU@rmk-PC.armlinux.org.uk
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use the header with DSI phy clock IDs to make code more readable.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250408-dts-qcom-dsi-phy-clocks-v2-24-73b482a6dd02@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use the header with DSI phy clock IDs to make code more readable.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250408-dts-qcom-dsi-phy-clocks-v2-23-73b482a6dd02@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use the header with DSI phy clock IDs to make code more readable.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250408-dts-qcom-dsi-phy-clocks-v2-22-73b482a6dd02@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use the header with DSI phy clock IDs to make code more readable.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250408-dts-qcom-dsi-phy-clocks-v2-21-73b482a6dd02@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use the header with DSI phy clock IDs to make code more readable.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250408-dts-qcom-dsi-phy-clocks-v2-20-73b482a6dd02@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use the header with DSI phy clock IDs to make code more readable.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250408-dts-qcom-dsi-phy-clocks-v2-19-73b482a6dd02@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use the header with DSI phy clock IDs to make code more readable.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250408-dts-qcom-dsi-phy-clocks-v2-18-73b482a6dd02@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use the header with DSI phy clock IDs to make code more readable.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250408-dts-qcom-dsi-phy-clocks-v2-17-73b482a6dd02@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use the header with DSI phy clock IDs to make code more readable.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250408-dts-qcom-dsi-phy-clocks-v2-16-73b482a6dd02@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use the header with DSI phy clock IDs to make code more readable.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250408-dts-qcom-dsi-phy-clocks-v2-15-73b482a6dd02@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use the header with DSI phy clock IDs to make code more readable.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250408-dts-qcom-dsi-phy-clocks-v2-14-73b482a6dd02@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use the header with DSI phy clock IDs to make code more readable.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250408-dts-qcom-dsi-phy-clocks-v2-13-73b482a6dd02@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use the header with DSI phy clock IDs to make code more readable.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250408-dts-qcom-dsi-phy-clocks-v2-12-73b482a6dd02@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use the header with DSI phy clock IDs to make code more readable.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250408-dts-qcom-dsi-phy-clocks-v2-11-73b482a6dd02@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use the header with DSI phy clock IDs to make code more readable.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250408-dts-qcom-dsi-phy-clocks-v2-10-73b482a6dd02@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use the header with DSI phy clock IDs to make code more readable.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250408-dts-qcom-dsi-phy-clocks-v2-9-73b482a6dd02@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use the header with DSI phy clock IDs to make code more readable.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250408-dts-qcom-dsi-phy-clocks-v2-8-73b482a6dd02@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use the header with DSI phy clock IDs to make code more readable.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250408-dts-qcom-dsi-phy-clocks-v2-7-73b482a6dd02@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use the header with DSI phy clock IDs to make code more readable.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250408-dts-qcom-dsi-phy-clocks-v2-6-73b482a6dd02@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use the header with DSI phy clock IDs to make code more readable.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250408-dts-qcom-dsi-phy-clocks-v2-5-73b482a6dd02@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use the header with DSI phy clock IDs to make code more readable.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250408-dts-qcom-dsi-phy-clocks-v2-4-73b482a6dd02@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use the header with DSI phy clock IDs to make code more readable.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250408-dts-qcom-dsi-phy-clocks-v2-3-73b482a6dd02@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Changes queued for v6.15 would have had the potential to break
bisectability and was therefor not accepted. Merge the whole set towards
v6.16, as this is no longer a concern.
Highlights:
- alienware-wmi: Refactor and split WMAX/legacy drivers
- dell-ddv:
- Correct +0.1 offset in temperature
- Use the power supply extension mechanism for battery temperatures
- intel/pmc:
- Refactor init to mostly use a common init function
- Add support for Arrow Lake U/H
- Add support for Panther Lake
- intel/sst:
- Improve multi die handling
- Prefix header search path with sysroot (fixes cross-compiling)
- lenovo-wmi-hotkey-utilities: Support for mic & audio mute LEDs
- samsung-galaxybook: Add driver for Samsung Galaxy Book series
- wmi:
- Rework WCxx/WExx ACPI method handling
- Enable data block collection when the data block is set
- platform/arm:
- Add Huawei Matebook E Go EC driver
- platform/mellanox:
- Relocate to drivers/platform/mellanox/
- mlxbf-bootctl: RTC battery status sysfs support
- Miscellaneous cleanups / refactoring / improvements
The following is an automated shortlog grouped by driver:
alienware-wmi:
- Add a state container for LED control feature
- Add a state container for thermal control methods
- Add alienware-wmi.h
- Add WMI Drivers
- Refactor hdmi, amplifier, deepslp methods
- Refactor LED control methods
- Refactor thermal control methods
- Rename alienware-wmi.c
- Split DMI table
- Split the alienware-wmi driver
- Update alienware-wmi config entries
- Update header and module information
amd/pmc:
- fix leak in probe()
- Move macros and structures to the PMC header file
- Notify user when platform does not support s0ix transition
- Remove unnecessary line breaks
- Use managed APIs for mutex
amd/pmf:
- convert timeouts to secs_to_jiffies()
amd:
- Use *-y instead of *-objs in Makefiles
arm64:
- add Huawei Matebook E Go EC driver
arm64: dts: qcom: gaokun3:
- Add Embedded Controller node
compal-laptop:
- Do not include <linux/fb.h>
dell-ddv:
- Fix temperature calculation
- Use devm_battery_hook_register
- Use the power supply extension mechanism
dell: dell-wmi-sysman:
- Use *-y instead of *-objs in Makefile
dell:
- Modify Makefile alignment
- Use *-y instead of *-objs in Makefile
dell-uart-backlight:
- Make dell_uart_bl_serdev_driver static
dt-bindings: platform:
- Add Huawei Matebook E Go EC
hp-bioscfg:
- Replace deprecated strncpy() with strscpy()
- Use wmi_instance_count()
hp:
- Use *-y instead of *-objs in Makefile
hwmon:
- (hp-wmi-sensors) Use the WMI bus API when accessing sensors
ideapad-laptop:
- use dev_groups to register attribute groups
int3472:
- Call "func" "con_id" instead
intel/pmc:
- Add Arrow Lake U/H support to intel_pmc_core driver
- Add Panther Lake support to intel_pmc_core
- Create generic_core_init() for all platforms
- Make tgl_core_generic_init() static
- Move arch specific action to init function
- Remove duplicate enum
- Remove simple init functions
- Remove unnecessary declarations in header
- Remove unneeded extern keyword in header
intel:
- Use *-y instead of *-objs in Makefile
irqdomain: platform/x86:
- Switch to irq_domain_create_linear()
lenovo-wmi-hotkey-utilities.c:
- Support for mic and audio mute LEDs
lenovo-yoga-tab2-pro-1380-fastcharger:
- Make symbol static
MAINTAINERS:
- Add documentation reference for Mellanox platform
- Update ALIENWARE WMI DRIVER entry
mellanox:
- Relocate mlx-platform driver
mlxbf-bootctl:
- Support sysfs entries for RTC battery status
mlx-platform:
- Change register name
- Cosmetic changes
samsung-galaxybook:
- Add samsung-galaxybook driver
- Fix block_recording not supported logic
sonypi:
- Use str_on_off() helper in sonypi_display_info()
think-lmi:
- Use ACPI object when extracting strings
- Use WMI bus API when accessing BIOS settings
thinkpad_acpi:
- check the return value of devm_mutex_init()
- convert timeouts to secs_to_jiffies()
- Do not include <linux/fb.h>
- Move HWMON initialization to tpacpi_hwmon_pdriver's probe
- Move subdriver initialization to tpacpi_pdriver's probe.
tools/power/x86/intel-speed-select:
- Die ID for IO dies
- Fix the condition to check multi die system
- Prefix header search path with sysroot
- Prevent increasing MAX_DIE_PER_PACKAGE
- v1.22 release
wmi:
- Call WCxx methods when setting data blocks
- Rework WCxx/WExx ACPI method handling
- Update documentation regarding the GUID-based API
- Use devres to disable the WMI device
x86-android-tablets:
- Add select POWER_SUPPLY to Kconfig
Merges:
- Merge branch 'fixes' into for-next
- Merge branch 'intel-sst' of https://github.com/spandruvada/linux-kernel into review-ilpo-next
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQSCSUwRdwTNL2MhaBlZrE9hU+XOMQUCZ+QJyQAKCRBZrE9hU+XO
MUPYAP4sjtB8DKTIHgiQqado7PJZmdgpeJfAplitwKGe4BOcEQEA1mhuqMA5n6S+
jvbTtRF+jiKxis/5zAtAdChScM/pIgo=
=W+gy
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v6.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform drivers updates from Ilpo Järvinen:
- alienware-wmi:
- Refactor and split WMAX/legacy drivers
- dell-ddv:
- Correct +0.1 offset in temperature
- Use the power supply extension mechanism for battery temperatures
- intel/pmc:
- Refactor init to mostly use a common init function
- Add support for Arrow Lake U/H
- Add support for Panther Lake
- intel/sst:
- Improve multi die handling
- Prefix header search path with sysroot (fixes cross-compiling)
- lenovo-wmi-hotkey-utilities:
- Support for mic & audio mute LEDs
- samsung-galaxybook:
- Add driver for Samsung Galaxy Book series
- wmi:
- Rework WCxx/WExx ACPI method handling
- Enable data block collection when the data block is set
- platform/arm:
- Add Huawei Matebook E Go EC driver
- platform/mellanox:
- Relocate to drivers/platform/mellanox/
- mlxbf-bootctl:
- RTC battery status sysfs support
- Miscellaneous cleanups / refactoring / improvements
* tag 'platform-drivers-x86-v6.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86: (75 commits)
platform/x86: x86-android-tablets: Add select POWER_SUPPLY to Kconfig
platform/x86/amd/pmf: convert timeouts to secs_to_jiffies()
platform/x86: thinkpad_acpi: convert timeouts to secs_to_jiffies()
irqdomain: platform/x86: Switch to irq_domain_create_linear()
platform/x86/amd/pmc: fix leak in probe()
tools/power/x86/intel-speed-select: v1.22 release
tools/power/x86/intel-speed-select: Prefix header search path with sysroot
tools/power/x86/intel-speed-select: Die ID for IO dies
tools/power/x86/intel-speed-select: Fix the condition to check multi die system
tools/power/x86/intel-speed-select: Prevent increasing MAX_DIE_PER_PACKAGE
platform/x86/amd/pmc: Use managed APIs for mutex
platform/x86/amd/pmc: Remove unnecessary line breaks
platform/x86/amd/pmc: Move macros and structures to the PMC header file
platform/x86/amd/pmc: Notify user when platform does not support s0ix transition
platform/x86: dell-ddv: Use the power supply extension mechanism
platform/x86: dell-ddv: Use devm_battery_hook_register
platform/x86: dell-ddv: Fix temperature calculation
platform/x86: thinkpad_acpi: check the return value of devm_mutex_init()
platform/x86: samsung-galaxybook: Fix block_recording not supported logic
platform/x86: dell-uart-backlight: Make dell_uart_bl_serdev_driver static
...
The ps8830 retimer reset is active low.
Fix up the retimer nodes which were based on an early version of the
driver which inverted the polarity.
Fixes: 019e1ee32f ("arm64: dts: qcom: x1e001de-devkit: Enable external DP support")
Cc: Sibi Sankar <quic_sibis@quicinc.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20250318074907.13903-1-johan+linaro@kernel.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add RPMh stats to read low power statistics for various subsystem
and SoC sleep modes.
Signed-off-by: Maulik Shah <maulik.shah@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250317-add_qcom_stats-v1-1-016ae05ac4b0@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add a node for the nss clock controller found on ipq9574 based devices.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Devi Priya <quic_devipriy@quicinc.com>
Signed-off-by: Manikanta Mylavarapu <quic_mmanikan@quicinc.com>
Link: https://lore.kernel.org/r/20250313110359.242491-6-quic_mmanikan@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
On many Qualcomm platforms the PMIC RTC control and time registers are
read-only so that the RTC time can not be updated. Instead an offset
needs be stored in some machine-specific non-volatile memory, which a
driver can take into account.
On X1E based Windows on Arm machines the offset is stored in a Qualcomm
specific UEFI variable.
Unlike on previous platforms the alarm registers are also unaccessible
on X1E as they are owned by the ADSP.
Assume all X1E machines use similar firmware and enable the RTC in the
PMIC dtsi for now.
Based on a patch by Jonathan Marek. [1]
Link: https://lore.kernel.org/r/20241015004945.3676-4-jonathan@marek.ca # [1]
Tested-by: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
Tested-by: Joel Stanley <joel@jms.id.au>
Tested-by: Sebastian Reichel <sre@kernel.org> # Lenovo T14s Gen6
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20250219134118.31017-7-johan+linaro@kernel.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
On many Qualcomm platforms the PMIC RTC control and time registers are
read-only so that the RTC time can not be updated. Instead an offset
needs be stored in some machine-specific non-volatile memory, which a
driver can take into account.
Switch to using the Qualcomm specific UEFI variable that is used by the
UEFI firmware (and Windows) to store the RTC offset.
This specifically means that the RTC time will be synchronised between
the UEFI firmware setup (or UEFI shell), Windows and Linux.
Note however that Windows stores the RTC time in local time by default,
while Linux typically uses UTC (i.e. as on X86).
Tested-by: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
Tested-by: Steev Klimaszewski <steev@kali.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20250219134118.31017-6-johan+linaro@kernel.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
On SM8650 the CPUs 0-1 are "silver" (Cortex-A520), CPU 2-6 are "gold"
(Cortex-A720) and CPU 7 is "gold-plus" (Cortex-X4).
So reference the correct "gold" idle-state for CPU core 2.
Fixes: d235037799 ("arm64: dts: qcom: add initial SM8650 dtsi")
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250314-sm8650-cpu2-sleep-v1-1-31d5c7c87a5d@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
