Add audio support for the NVIDIA IGX Orin development kit having P3701
module with P3740 carrier board.
Move the common device-tree nodes to a new file tegra234-p3701.dtsi and
use this for Jetson AGX Orin and NVIDIA IGX Orin platforms
Signed-off-by: Mohan Kumar <mkumard@nvidia.com>
[treding@nvidia.com: properly sort nodes]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Update the CPU OPP table to include all frequencies supported by
Tegra234. Different platforms can choose to keep all or few entries
based on their power and performance tunings.
Signed-off-by: Shao-Chun Kao <shaochunk@nvidia.com>
Signed-off-by: Sumit Gupta <sumitg@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
After commit 71de0a054d ("arm64: tegra: Drop serial clock-names and
reset-names") was applied, the HSUART failed to probe and the following
error is seen:
serial-tegra 70006300.serial: Couldn't get the reset
serial-tegra: probe of 70006300.serial failed with error -2
Commit 71de0a054d ("arm64: tegra: Drop serial clock-names and
reset-names") is correct because the "reset-names" property is not
needed for 8250 UARTs. However, the "reset-names" is required for the
HSUART and should have been populated as part of commit a63c0cd837
("arm64: dts: tegra: smaug: Add Bluetooth node") that enabled the HSUART
for the Pixel C. Fix this by populating the "reset-names" property for
the HSUART on the Pixel C.
Fixes: a63c0cd837 ("arm64: dts: tegra: smaug: Add Bluetooth node")
Signed-off-by: Diogo Ivo <diogo.ivo@tecnico.ulisboa.pt>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
After commit 71de0a054d ("arm64: tegra: Drop serial clock-names and
reset-names") was applied, the HSUART failed to probe and the following
error is seen:
serial-tegra 3100000.serial: Couldn't get the reset
serial-tegra: probe of 3100000.serial failed with error -2
Commit 71de0a054d ("arm64: tegra: Drop serial clock-names and
reset-names") is correct because the "reset-names" property is not
needed for 8250 UARTs. However, the "reset-names" is required for the
HSUART and should have been populated as part of commit ff578db7b6
("arm64: tegra: Enable UART instance on 40-pin header") that
enabled the HSUART for Jetson AGX Orin. Fix this by populating the
"reset-names" property for the HSUART on Jetson AGX Orin.
Fixes: ff578db7b6 ("arm64: tegra: Enable UART instance on 40-pin header")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The following error is seen on boot for the NVIDIA IGX Orin platform ...
serial-tegra 3100000.serial: failed to get alias id, errno -19
Fix this by populating the necessary alias for the serial device.
Fixes: c95711d7db ("arm64: tegra: Add support for IGX Orin")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
I2S data sanity test failures are seen at lower AHUB clock rates
on Tegra234. The Tegra194 uses the same clock relationship for AHUB
and it is likely that similar issues would be seen. Thus update the
AHUB clock parent and rates here as well for Tegra194, Tegra186
and Tegra210.
Fixes: 177208f7b0 ("arm64: tegra: Add DT binding for AHUB components")
Cc: stable@vger.kernel.org
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
I2S data sanity tests fail beyond a bit clock frequency of 6.144MHz.
This happens because the AHUB clock rate is too low and it shows
9.83MHz on boot.
The maximum rate of PLLA_OUT0 is 49.152MHz and is used to serve I/O
clocks. It is recommended that AHUB clock operates higher than this.
Thus fix this by using PLLP_OUT0 as parent clock for AHUB instead of
PLLA_OUT0 and fix the rate to 81.6MHz.
Fixes: dc94a94daa ("arm64: tegra: Add audio devices on Tegra234")
Cc: stable@vger.kernel.org
Signed-off-by: Sheetal <sheetal@nvidia.com>
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Mohan Kumar D <mkumard@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Enable the TJ thermal zone and hook up cooling maps for the PWM-
controlled fan and two trip points.
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Enable the TJ thermal zone and hook up cooling maps for the PWM-
controlled fan and two trip points.
This also removes a duplicate definition of the PWM fan and changes its
cooling levels. This should have no effect, though, because the fan
wasn't previously connected to anything and by default would be turned
off at probe time.
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add thermal zone details and enable the PWM fan as cooling device.
Note that this also changes the cooling levels for the PWM fan, which
should have no effect, though, because the fan wasn't previously
connected to anything and by default would be turned off at probe time.
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add device tree node for the BPMP thermal node on Tegra234 and add
thermal zone definitions.
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Surround device tree nodes with blank lines for increased readability.
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
We typically sort the "compatible" property first because it defines
what the remainder of the properties can be. For the sound node on the
Jetson AGX Orin this wasn't done, so fix that up.
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the GPU power rail regulator node for the Pixel C.
Signed-off-by: Diogo Ivo <diogo.ivo@tecnico.ulisboa.pt>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Running 'make dtbs_check' reports the following warning for the Jetson
Orin NX platform ...
arch/arm64/boot/dts/nvidia/tegra234-p3768-0000+p3767-0000.dtb:
usb@3550000: phy-names:1: 'usb3-0' was expected
Fix this by updating the phy-names:1 to be 'usb3-0' as expected.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Enable USB device support for the Jetson AGX Orin platform and update
the mode for the usb2-0 port to be on-the-go.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the device tree nodes for the MAIN and AON pin controllers found on
the Tegra234 family of SoCs.
Signed-off-by: Prathamesh Shete <pshete@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The NVIDIA Jetson Orin Nano Developer Kit is the combination of the
NVIDIA Jetson Orin Nano (P3767, SKU 5) module and the P3768 carrier
board.
Signed-off-by: Thierry Reding <treding@nvidia.com>
As all level 2 and level 3 caches are unified, add required
cache-unified property to fix warnings like:
tegra210-p2371-0000.dtb: l2-cache: 'cache-unified' is a required property
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The PCIe slot on the Jetson Orin AGX is not working and PCIe cards
are not detected. The regulator for the 3.3V regulator for the PCIe is
using the wrong GPIO for turning on the regulator. Fix this by updating
the 3.3V regulator to use the correct GPIO.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add OPP table and interconnects property to scale DDR frequency with
CPU frequency for better performance. Each operating point entry of
the OPP table has CPU freq to per MC channel bandwidth mapping.
One table is added for each cluster even though the table data is
same because the bandwidth request is per cluster. This is done
because OPP framework creates a single icc path and hence single
bandwidth request if the table is marked as 'opp-shared' and shared
among all clusters. For us, the OPP table data is same but the MC
Client ID argument to interconnects property is different for each
cluster. So, having per cluster table makes different icc path for
each cluster and helps to make per cluster BW requests.
Signed-off-by: Sumit Gupta <sumitg@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add support for the NVIDIA IGX Orin development kit having P3701
module with P3740 carrier board.
Signed-off-by: Shubhi Garg <shgarg@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The changes for the hte/timestamp subsystem include the following:
- Add Tegra234 HTE provider and relevant DT bindings
- Update MAINTAINERS file for the HTE subsystem
-----BEGIN PGP SIGNATURE-----
iIgEABYIADAWIQT4slW2T0Q/rXAa29f4pUxhzZTZKAUCZErbLBIcZGlwZW5wQG52
aWRpYS5jb20ACgkQ+KVMYc2U2SiW0QEAt3bPgopjIMzaInOguZthR1pHCuKtyK7F
u4aJAyHv7tIA/jtsFJuFO4LmiwA/IsNits5l7F36oaB94/cQGuRH1M8E
=opcL
-----END PGP SIGNATURE-----
Merge tag 'for-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/pateldipen1984/linux
Pull hardware timestamp engine updates from Dipen Patel:
"The changes for the hte subsystem include:
- Add Tegra234 HTE provider and relevant DT bindings
- Update MAINTAINERS file for the HTE subsystem"
* tag 'for-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/pateldipen1984/linux:
hte: tegra-194: Use proper includes
hte: Use device_match_of_node()
hte: tegra-194: Fix off by one in tegra_hte_map_to_line_id()
hte: tegra: fix 'struct of_device_id' build error
hte: Use of_property_present() for testing DT property presence
gpio: tegra186: Add Tegra234 hte support
hte: handle nvidia,gpio-controller property
hte: Deprecate nvidia,slices property
hte: Add Tegra234 provider
hte: Re-phrase tegra API document
arm64: tegra: Add Tegra234 GTE nodes
dt-bindings: timestamp: Deprecate nvidia,slices property
dt-bindings: timestamp: Add Tegra234 support
MAINTAINERS: Add HTE/timestamp subsystem details
The devicetree changes overall are again dominated by the Qualcomm
Snapdragon platform that weighs in at over 300 changesets, but there
are many updates across other platforms as well, notably Mediatek, NXP,
Rockchips, Renesas, TI, Samsung and ST Microelectronics. These all
add new features for existing machines, as well as new machines and
SoCs.
The newly added SoCs are:
- Allwinner T113-s, an Cortex-A7 based variant of the RISC-V
based D1 chip.
- StarFive JH7110, a RISC-V SoC based on the Sifive U74 core
like its JH7100 predecessor, but with additional CPU cores
and a GPU.
- Apple M2 as used in current Macbook Air/Pro and Mac Mini
gets added, with comparable support as its M1 predecessor.
- Unisoc UMS512 (Tiger T610) is a midrange smartphone SoC
- Qualcomm IPQ5332 and IPQ9574 are Wi-Fi 7 networking SoCs,
based on the Cortex-A53 and Cortex-A73 cores, respectively.
- Qualcomm sa8775p is an automotive SoC derived from the
Snapdragon family.
Including the initial board support for the added SoC platforms,
there are 52 new machines. The largest group are 19 boards
industrial embedded boards based on the NXP i.MX6 (32-bit)
and i.MX8 (64-bit) families.
Others include:
- Two boards based on the Allwinner f1c200s ultra-low-cost chip
- Three "Banana Pi" variants based on the Amlogic g12b
(A311D, S922X) SoC.
- The Gl.Inet mv1000 router based on Marvell Armada 3720
- A Wifi/LTE Dongle based on Qualcomm msm8916
- Two robotics boards based on Qualcomm QRB chips
- Three Snapdragon based phones made by Xiaomi
- Five developments boards based on various Rockchip SoCs,
including the rk3588s-khadas-edge2 and a few NanoPi
models
- The AM625 Beagleplay industrial SBC
Another 14 machines get removed: both boards for the obsolete "oxnas"
platform, three boards for the Renesas r8a77950 SoC that were only for
pre-production chips, and various chromebook models based on the Qualcomm
Sc7180 "trogdor" design that were never part of products.
-----BEGIN PGP SIGNATURE-----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=j12m
-----END PGP SIGNATURE-----
Merge tag 'soc-dt-6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC devicetree updates from Arnd Bergmann:
"The devicetree changes overall are again dominated by the Qualcomm
Snapdragon platform that weighs in at over 300 changesets, but there
are many updates across other platforms as well, notably Mediatek,
NXP, Rockchips, Renesas, TI, Samsung and ST Microelectronics. These
all add new features for existing machines, as well as new machines
and SoCs.
The newly added SoCs are:
- Allwinner T113-s, an Cortex-A7 based variant of the RISC-V based D1
chip.
- StarFive JH7110, a RISC-V SoC based on the Sifive U74 core like its
JH7100 predecessor, but with additional CPU cores and a GPU.
- Apple M2 as used in current Macbook Air/Pro and Mac Mini gets
added, with comparable support as its M1 predecessor.
- Unisoc UMS512 (Tiger T610) is a midrange smartphone SoC
- Qualcomm IPQ5332 and IPQ9574 are Wi-Fi 7 networking SoCs, based on
the Cortex-A53 and Cortex-A73 cores, respectively.
- Qualcomm sa8775p is an automotive SoC derived from the Snapdragon
family.
Including the initial board support for the added SoC platforms, there
are 52 new machines. The largest group are 19 boards industrial
embedded boards based on the NXP i.MX6 (32-bit) and i.MX8 (64-bit)
families.
Others include:
- Two boards based on the Allwinner f1c200s ultra-low-cost chip
- Three 'Banana Pi' variants based on the Amlogic g12b (A311D, S922X)
SoC.
- The Gl.Inet mv1000 router based on Marvell Armada 3720
- A Wifi/LTE Dongle based on Qualcomm msm8916
- Two robotics boards based on Qualcomm QRB chips
- Three Snapdragon based phones made by Xiaomi
- Five developments boards based on various Rockchip SoCs, including
the rk3588s-khadas-edge2 and a few NanoPi models
- The AM625 Beagleplay industrial SBC
Another 14 machines get removed: both boards for the obsolete 'oxnas'
platform, three boards for the Renesas r8a77950 SoC that were only for
pre-production chips, and various chromebook models based on the
Qualcomm Sc7180 'trogdor' design that were never part of products"
* tag 'soc-dt-6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (836 commits)
arm64: dts: rockchip: Add support for volume keys to rk3399-pinephone-pro
arm64: dts: rockchip: Add vdd_cpu_big regulators to rk3588-rock-5b
arm64: dts: rockchip: Use generic name for es8316 on Pinebook Pro and Rock 5B
arm64: dts: rockchip: Drop RTC clock-frequency on rk3588-rock-5b
arm64: dts: apple: t8112: Add PWM controller
arm64: dts: apple: t600x: Add PWM controller
arm64: dts: apple: t8103: Add PWM controller
arm64: dts: rockchip: Add pinctrl gpio-ranges for rk356x
ARM: dts: nomadik: Replace deprecated spi-gpio properties
ARM: dts: aspeed-g6: Add UDMA node
ARM: dts: aspeed: greatlakes: add mctp device
ARM: dts: aspeed: greatlakes: Add gpio names
ARM: dts: aspeed: p10bmc: Change power supply info
arm64: dts: mediatek: mt6795-xperia-m5: Add Bosch BMM050 Magnetometer
arm64: dts: mediatek: mt6795-xperia-m5: Add Bosch BMA255 Accelerometer
arm64: dts: mediatek: mt6795: Add tertiary PWM node
arm64: dts: rockchip: add panel to Anbernic RG353 series
dt-bindings: arm: Add Data Modul i.MX8M Plus eDM SBC
dt-bindings: arm: fsl: Add chargebyte Tarragon
dt-bindings: vendor-prefixes: add chargebyte
...
The TX2 SoM's SDIO WiFI card is connected via mmc@3440000 however it does
not look like the upstream kernel is even bothering to power this (and
the regulator framework shuts down this power rail post kernel init).
The issue seems to be a missing link for vccq from the MAX77620 PMIC's LDO5
which is labeled vddio_sdmmc3 (and not used anywhere else) to the mmc@3440000
node to ensure there is at leasr bus power.
Note this does not fix the WiFi issue on upstream kernels, there is still
something else missing that gets the BCM WiFi device to detect properly.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the USB Type-C controller that is present on the Jetson AGX Orin
board. The ports for the Type-C controller are not populated yet, but
will be added later once the USB host and device support for Jetson AGX
Orin is enabled.
This is based upon a patch from Wayne Chang <waynec@nvidia.com>.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Jetson AGX Orin has onboard RT5640 audio codec. This patch adds the
codec device node and the bindings to I2S1 interface.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add support for the combination of the NVIDIA Jetson Orin NX (P3767, SKU
0) module and the P3768 carrier board.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This adds a device tree for the Jetson Orin NX module, which is Jetson
AGX Orin's little sibling with 6 or 8 ARM Cortex-A78AE cores, an Ampere
GPU (1024 GPU and 32 tensor cores) and a number of accelerators for
machine learning, image processing and more.
The Jetson Orin NX comes with either 8 or 16 GiB of 128-bit LPDDR5 and
supports NVME for mass storage.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Populate the DynamIQ Shared Unit (DSU) Performance Monitor Unit (PMU)
devices for Tegra234 which has one DSU PMU per CPU cluster.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The serial node does not use clock-names and reset-names:
tegra234-sim-vdk.dtb: serial@3100000: Unevaluated properties are not allowed ('clock-names', 'reset-names' were unexpected)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Both Xavier (Tegra194) and Orin (Tegra234) support a 40-bit address map,
so bump the CBB ranges property to cover all of the 1 TiB address space.
This fixes an issue where some of the PCIe regions could not be remapped
because of they were outside the memory specified by the CBB's ranges
property.
Reported-by: Jonathan Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Drop the iommus and dma-coherent properties for the I2C controller
device tree nodes. These are only needed for the device tree nodes
that represent the GPC DMA controller, since that is the device
performing the direct memory accesses.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Ensure appropriate configuration is done to make the host1x device
and context devices DMA coherent by adding the dma-coherent flag.
Fixes: b35f5b53a8 ("arm64: tegra: Add context isolation domains on Tegra234")
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Populate the Tegra XUSB device controller (XUDC) node for Tegra234.
This is based upon a patch from Wayne Chang <waynec@nvidia.com>.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
DMA operations for XUSB device controller (XUDC) are coherent for
Tegra194 and so add the 'dma-coherent' property for this device.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Populate the module and system EEPROMs on the Jetson AGX Orin platform.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Populate the address and size cells properties for the I2C devices on
Tegra234.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This commit enables XUSB host and pad controller on Jetson AGX Orin.
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Nodes in device tree should be sorted by unit-address, followed by nodes
without a unit-address, sorted alphabetically. Some exceptions are the
top-level aliases, chosen, firmware, memory and reserved-memory nodes,
which are expected to come first.
These rules apply recursively with some exceptions, such as pinmux nodes
or regulator nodes, which often follow more complicated ordering (often
by "importance").
While at it, change the name of some of the nodes to follow standard
naming conventions, which helps with the sorting order and reduces the
amount of warnings from the DT validation tools.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The #address-cells and #size-cells properties for the top-level bus were
set to 1 because that was enough to represent the register ranges of all
the IP blocks on that bus. However, most of these devices can do DMA to
a larger address space, so translation of DMA addresses needs to happen
in a 64-bit address space.
Partially this was already done by the memory controller increasing that
address space by setting #address-cells and #size-cells to 2, but a full
DMA address translation would still cause truncation when traversing to
the top-level bus.
Fix this by setting #address-cells = <2> and #size-cells = <2> on the
top-level bus and adjusting all "reg" and "ranges" properties of its
children.
While at it, also move the PCI and GPU nodes back under the top-level
bus where they belong. The were put outside of it to work around this
same problem.
Signed-off-by: Thierry Reding <treding@nvidia.com>
When the top-level regulators were renamed, the 1.2V camera regulator
accidentally ended up with the same DT node name as the 1.8V camera
regulator.
Fixes: 097e01c610 ("arm64: tegra: Rename top-level regulators")
Signed-off-by: Thierry Reding <treding@nvidia.com>
The gpio-ranges property name was missing a terminating "s", causing it
to not be parsed and fail DT validation as well.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The compatible string list for SDHCI on Tegra234 should be
"nvidia,tegra234-sdhci", followed by the "nvidia,tegra186-sdhci"
fallback. Use that consistently for all SDHCI controllers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Tegra QSPI controller uses a single reset line, so there's no need
for a reset-names property. Remove such properties.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Pinmux node names should have a pinmux- prefix and not use underscores.
Fix up some cases that didn't follow those rules.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Tegra QSPI controllers use a single reset control, so reset-names is
not necessary and therefore not specified in the DT bindings. Drop the
property from device tree files to avoid validation warnings.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Tegra234 HDA controller is not backwards-compatible with Tegra30, so
drop the corresponding compatible string from the list.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Tegra194 HDA controller is not backwards-compatible with Tegra30, so
drop the corresponding compatible string from the list.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Instead of using the deprecated vbus-gpio property, switch to using the
more standard vbus-gpios property.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The PMC pinmux configuration nodes need to be part of a top-level pinmux
node. Add that new "pinmux" node and move the configuration nodes into
it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DeviceTree Specification v0.3 specifies that the cache node
'compatible' and 'cache-level' properties are 'required'. Cf.
s3.8 Multi-level and Shared Cache Nodes
The 'cache-unified' property should be present if one of the
properties for unified cache is present ('cache-size', ...).
Update the Device Trees accordingly.
Signed-off-by: Pierre Gondois <pierre.gondois@arm.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The 'enable-active-low' property is not a valid one.
Only 'enable-active-high' is valid, and when this property is absent
the gpio regulator will act as active low by default.
Remove the invalid 'enable-active-low' property.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add dma-channel-mask property in Tegra GPCDMA device tree node.
The property would help to specify the channels to be used in
kernel and reserve few for the firmware. This was previously
achieved by limiting the channel number to 31 in the driver.
This is wrong and does not align with the hardware. Correct this
and update the interrupts property to list all 32 interrupts.
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
According to the DT schema in usb-device.yaml, each USB device node
needs a compatible string, so add one for the built-in USB Ethernet
device on Jetson TX1.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The registers for the AON pinmux reside in a partition different from
the registers for the main pinmux. Instead of treating them as one and
the same device, split them up so that they are each their own devices.
Also add gpio-ranges properties to the corresponding GPIO controllers
such that the pinmux and GPIO controllers can be paired up properly.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the ECAM aperture information for all the PCIe controllers of
Tegra234.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Tegra PWFM controllers use a single clock, so there's no need for a
clock-names property.
Suggested-by: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Tegra Combined UART (TCU) is the default serial interface for Jetson
Xavier and Orin platforms and so update the bootargs for these platforms
to use the TCU.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Enable additional PWM controllers in device tree so that the PWM pins on
the Jetson AGX Orin Developer Kit 40-pin header can be used.
Signed-off-by: Sandipan Patra <spatra@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The P2U nodes that were recently added were not added in the correct
order. Sort them in the right place by unit-address.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Populate the SBSA UART for Tegra234 and enable this UART for Jetson AGX
Orin.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the PWM fan node for the Tegra234 Jetson AGX Orin platform.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Populate all the PWM devices for Tegra234. Finally, update the
compatible string for the existing 'pwm1' node to just be 'tegra194-pwm'
and remove the fallback to 'tegra186-pwm', which aligns with the
binding documentation.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Commit 156af9de09 ("arm64: tegra: Add Tegra234 I2C devicetree nodes")
populated the I2C device nodes for Tegra234. One of these nodes
contains the property 'nvidia,hw-instance-id' which is neither
documented or used. Remove this unused property.
Fixes: 156af9de09 ("arm64: tegra: Add Tegra234 I2C devicetree nodes")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
commit edf408b946 ("PCI: dwc: Validate iATU outbound mappings against
hardware constraints") exposes an issue with the existing partitioning of
the aperture space where the Prefetchable apertures of controllers
C5, C7 and C9 in Tegra234 cross the 32GB boundary hardware constraint.
This patch makes sure that the Prefetchable region doesn't spill over
the 32GB boundary.
Fixes: ec142c44b0 ("arm64: tegra: Add P2U and PCIe controller nodes to Tegra234 DT")
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add a device tree node for NVDEC on Tegra234.
Booting the firmware requires some information regarding offsets
within the firmware binary. These are passed through the device
tree, but since the values vary depending on the firmware version,
and the firmware itself is not available to the OS, the flasher is
expected to provide a device tree overlay with values corresponding
to the firmware it is flashing. The overlay then replaces the
placeholder values here.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The currently specified 'ranges' properties don't actually include
all devices under the host1x bus on Tegra194 and Tegra234. Expand
them appropriately.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add dma properties to support GPCDMA for I2C in Tegra 186 and later
chips
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the iommus property to the HDA node on Tegra234.
Signed-off-by: Mohan Kumar <mkumard@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add Host1x context isolation domains on Tegra234. On Tegra234 we have
two IOMMUs that are connected to Host1x-channel programmed engines,
so we have to include domains for each of them.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Make sure that each phandle-array is enclosed in a set of angular
brackets and properly indent each entry.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Google Pixel C contains a BRCM4354 Wi-Fi + BT module.
Add a DT node for its Wi-Fi functionality. Tested on Pixel C.
Signed-off-by: Diogo Ivo <diogo.ivo@tecnico.ulisboa.pt>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Google Pixel C contains a BRCM4354 Wi-Fi + BT module.
Add a DT node for its BT functionality. Tested on Pixel C.
Signed-off-by: Diogo Ivo <diogo.ivo@tecnico.ulisboa.pt>
Signed-off-by: Thierry Reding <treding@nvidia.com>
A Multi-Gigabit Ethernet (MGBE) instance drives the primary Ethernet
port on the Jetson AGX Orin Developer Kit. Enable it.
Signed-off-by: Bhadram Varka <vbhadram@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add device tree nodes for the four instances of the Multi-Gigabit
Ethernet (MGBE) IP found on NVIDIA Tegra234 SoCs.
Signed-off-by: Bhadram Varka <vbhadram@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
There is no need to list the Tegra194-specific compatible for Tegra234
because the backwards-compatibility goes back all the way to Tegra186.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Hook SDMMC1 CD up with CVM GPIO02 (SOC_GPIO11) used for card detection on J4
(uSD socket) on the carrier.
Fixes: ef633bfc21 ("arm64: tegra: Enable card detect for SD card on P2888")
Signed-off-by: Tamás Szűcs <tszucs@protonmail.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use the compatible specific to Tegra234 for GPCDMA to support
additional features.
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add device tree nodes for Host1x and VIC on Tegra234.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add Host1x context stream IDs on systems that support Host1x context
isolation. Host1x and attached engines can use these stream IDs to
allow isolation between memory used by different processes.
The specified stream IDs must match those configured by the hypervisor,
if one is present.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The native timers IP block found on NVIDIA Tegra SoCs implements a
watchdog timer that can be used to recover from system hangs. Add and
enable the device tree node on Tegra234.
Signed-off-by: Kartik <kkartik@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The native timers IP block found on NVIDIA Tegra SoCs implements a
watchdog timer that can be used to recover from system hangs. Add and
enable the device tree node on Tegra194.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Kartik <kkartik@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Enable the native timers on Tegra186 chips to allow using the watchdog
functionality to recover from system hangs.
Signed-off-by: Kartik <kkartik@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra234 uses the Control Backbone (CBB) version 2.0. Add the nodes
that enable error handling from the various CBB 2.0 fabrics found on
Tegra234.
Signed-off-by: Sumit Gupta <sumitg@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add device tree nodes to enable error handling on the Control Backbone
(CBB). Tegra194 uses CBB version 1.0.
Signed-off-by: Sumit Gupta <sumitg@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The node names should be generic and DT schema expects certain pattern
(e.g. with key/button/switch).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Tegra SYSRAM contains regions access to which is restricted to
certain hardware blocks on the system, and speculative accesses to
those will cause issues.
Patch 'misc: sram: Only map reserved areas in Tegra SYSRAM' attempted
to resolve this by only mapping the regions specified in the device
tree on the assumption that there are no such restricted areas within
the 64K-aligned area of memory that contains the memory we wish to map.
Turns out this assumption is wrong, as there are such areas above the
4K pages described in the device trees. As such, we need to use the
bigger hammer that is no-memory-wc, which causes the memory to be
mapped as Device memory to which speculative accesses are disallowed.
As such, the previous patch in the series,
'firmware: tegra: bpmp: do only aligned access to IPC memory area',
is required with this patch to make the BPMP driver only issue aligned
memory accesses as those are also required with Device memory.
Fixes: fec29bf049 ("misc: sram: Only map reserved areas in Tegra SYSRAM")
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Reviewed-by: Yousaf Kaukab <ykaukab@suse.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add device tree nodes for Tegra234 GPCDMA
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Fix whitespace coding style: use single space instead of tabs or
multiple spaces around '=' sign in property assignment. No functional
changes (same DTB).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Enable OPE module usage on various Jetson platforms. This can be plugged
into an audio path using ALSA mixer controls. Add audio-graph-port binding
to use OPE device with generic audio-graph based sound card.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Output Processing Engine (OPE) is a client of AHUB and is present on
Tegra210 and later generations of Tegra SoC. Add this device on the
relevant SoC DTSI files.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Commit 4782c0a5dd ("clk: tegra: Don't deassert reset on enabling
clocks") removed deassertion of reset lines when enabling peripheral
clocks. This breaks the initialization of the DFLL driver which relied
on this behaviour.
In order to be able to fix this, add the corresponding reset to the DT.
Tested on Google Pixel C.
Cc: stable@vger.kernel.org
Fixes: 4782c0a5dd ("clk: tegra: Don't deassert reset on enabling clocks")
Signed-off-by: Diogo Ivo <diogo.ivo@tecnico.ulisboa.pt>
Signed-off-by: Thierry Reding <treding@nvidia.com>
From tegra186 onwards, memory controller support multiple channels.
During the error interrupts from memory controller, corresponding
channels need to be accessed for logging error info and clearing the
interrupt.
So add address and size of these channels in device tree node of
tegra186, tegra194 and tegra234 memory controller. Also add reg-names
for each of these reg items which are used by driver for mapping.
Signed-off-by: Ashish Mhetre <amhetre@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Enable ASRC module usage on various Jetson Platforms. This can be plugged
into an audio path using ALSA mixer controls.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Asynchronous Sample Rate Converter (ASRC) is a client of AHUB and is
present on Tegra186 and later generations of Tegra SoC. Add this device
on the relevant SoC DTSI files.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
According to the device-tree binding document for PWM fans [0], the
PWM fan node name should be 'pwm-fan'. Update the PWM fan node name to
align with this.
[0] Documentation/devicetree/bindings/hwmon/pwm-fan.txt
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Adding CCPLEX cluster node to represent Tegra234 cpufreq. Tegra234 uses
some of the CRAB (Control Register Access Bus) registers for CPU
frequency requests. These registers are memory mapped to the
CCPLEX_MMCRAB_ARM region. In this node, mapping the range of MMCRAB
registers is required only for CPU frequency info.
Signed-off-by: Sumit Gupta <sumitg@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This adds the QSPI controllers on the Tegra234 SoC and populates the
SPI NOR flash device for the Jetson AGX Orin platform.
Signed-off-by: Ashish Singhal <ashishsingha@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The default parent for SDMMC1/3 clock sources can provide maximum frequency
of 136MHz for SDR104 mode.
Update parent clock source for SDMMC1/SDMMC3 instances
to increase the output clock frequency to 195MHz and improve the perf.
Signed-off-by: Aniruddha Rao <anrao@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
After a somewhat quiet 5.17 release, the size of the DT changes
is a bit larger again. There are nine new SoC that get added,
all of them related to existing platforms:
- Airoha (formerly Mediatek/EcoNet) EN7523 networking SoC and EVB
- Mediatek mt6582 tablet platform with the Prestigio PMT5008 3G tablet
- Microchip Lan966 networking SoC and it evaluation board
- Qualcomm Snapdragon 625/632 midrange phone SoCs, with the
LG Nexus 5X and Fairphone FP3 phones
- Renesas RZ/G2LC and RZ/V2L general-purpose embedded SoCs,
along with their evaluation boards
- Samsung Exynos 850 phone SoC and reference board
- Samsung Exynos7885 with the Samsung Galaxy A8 (2018) phone
- Tesla FSD (Fully Self-Driving), an automotive SoC losely derived
from the Samsung Exynos family.
- TI K3/AM62 SoC and reference board
Support for additional functionality in existing dts files is added all
over the place: Samsung, Renesas, Mstar, wpcm450, OMAP, AT91, Allwinner,
i.MX, Tegra, Aspeed, Oxnas, Qualcomm, Mediatek, and Broadcom.
Samsung has a rework for its pinctrl schema that is a bit tricky and
requires driver changes to be included here.
A few more platforms only have smaller cleanups and DT Schema fixes,
this includes SoCFPGA, ux500, ixp4xx, STi, Xilinx Zynq, LG, and Juno.
The new machines are really too many to list, but I'll do it anyway:
Allwinner:
- A20-Marsboard development board
Amlogic
- Amediatek X96-AIR (Amlogic S905X3)
- CYX A95XF3-AIR (Amlogic S905X3)
- Haochuangy H96-Max (Amlogic S905X3)
- Amlogic AQ222 (Amlogic S4)
- OSMC Vero 4K+ (Amlogic S905D)
Arm Juno
- Separate DT depending on SCMI firmware version
Aspeed:
- Quanta S6Q BMC (AST2600)
- ASRock ROMED8HM3 (AST2500)
Broadcom:
- Raspberry Pi Zero 2 W
Marvell MVEBU/Armada:
- Ctera C200 V1 NAS (kirkwood)
- Ctera C200 V2 NAS (armada-370)
Mstar
- DongShanPiOne, a low-end embedded board
- Miyoo Mini handheld game console
NXP i.MX:
- Numerous i.MX8M Mini based boards in even more variations, but
none based on other SoCs this time:
Protonic PRT8MM, emCON-MX8M Mini, Toradex Verdin, and
Gateworks GW7903
Qualcomm:
- Google Herobrine R1 Chromebook platform (Snapdragon 7c Gen 3)
- SHIFT6mq phone (Snapdragon 845)
- Samsung Galaxy Book2 (Snapdragon 850)
- Snapdragon 8 Gen 1 Hardware Development Kit
TI OMAP:
- SanCloud BeagleBone Enhanced WiFi
Rockchip:
- Pine64 PineNote ereader tablet (rk356x)
- Bananapi-R2-Pro (rk356x)
STM32:
- emtrion emSBS-Argon embedded board (stm32mp157c)
-----BEGIN PGP SIGNATURE-----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=v98T
-----END PGP SIGNATURE-----
Merge tag 'arm-dt-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM devicetree updates from Arnd Bergmann:
"After a somewhat quiet 5.17 release, the size of the DT changes is a
bit larger again. There are nine new SoC that get added, all of them
related to existing platforms:
- Airoha (formerly Mediatek/EcoNet) EN7523 networking SoC and EVB
- Mediatek mt6582 tablet platform with the Prestigio PMT5008 3G
tablet
- Microchip Lan966 networking SoC and it evaluation board
- Qualcomm Snapdragon 625/632 midrange phone SoCs, with the LG Nexus
5X and Fairphone FP3 phones
- Renesas RZ/G2LC and RZ/V2L general-purpose embedded SoCs, along
with their evaluation boards
- Samsung Exynos 850 phone SoC and reference board
- Samsung Exynos7885 with the Samsung Galaxy A8 (2018) phone
- Tesla FSD (Fully Self-Driving), an automotive SoC loosely derived
from the Samsung Exynos family.
- TI K3/AM62 SoC and reference board
Support for additional functionality in existing dts files is added
all over the place: Samsung, Renesas, Mstar, wpcm450, OMAP, AT91,
Allwinner, i.MX, Tegra, Aspeed, Oxnas, Qualcomm, Mediatek, and
Broadcom.
Samsung has a rework for its pinctrl schema that is a bit tricky and
requires driver changes to be included here.
A few more platforms only have smaller cleanups and DT Schema fixes,
this includes SoCFPGA, ux500, ixp4xx, STi, Xilinx Zynq, LG, and Juno.
The new machines are really too many to list, but I'll do it anyway:
Allwinner:
- A20-Marsboard development board
Amlogic:
- Amediatek X96-AIR (Amlogic S905X3)
- CYX A95XF3-AIR (Amlogic S905X3)
- Haochuangy H96-Max (Amlogic S905X3)
- Amlogic AQ222 (Amlogic S4)
- OSMC Vero 4K+ (Amlogic S905D)
Arm Juno:
- Separate DT depending on SCMI firmware version
Aspeed:
- Quanta S6Q BMC (AST2600)
- ASRock ROMED8HM3 (AST2500)
Broadcom:
- Raspberry Pi Zero 2 W
Marvell MVEBU/Armada:
- Ctera C200 V1 NAS (kirkwood)
- Ctera C200 V2 NAS (armada-370)
Mstar:
- DongShanPiOne, a low-end embedded board
- Miyoo Mini handheld game console
NXP i.MX:
- Numerous i.MX8M Mini based boards in even more variations, but
none based on other SoCs this time:
Protonic PRT8MM, emCON-MX8M Mini, Toradex Verdin, and
Gateworks GW7903
Qualcomm:
- Google Herobrine R1 Chromebook platform (Snapdragon 7c Gen 3)
- SHIFT6mq phone (Snapdragon 845)
- Samsung Galaxy Book2 (Snapdragon 850)
- Snapdragon 8 Gen 1 Hardware Development Kit
TI OMAP:
- SanCloud BeagleBone Enhanced WiFi
Rockchip:
- Pine64 PineNote ereader tablet (rk356x)
- Bananapi-R2-Pro (rk356x)
STM32:
- emtrion emSBS-Argon embedded board (stm32mp157c)"
* tag 'arm-dt-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (627 commits)
arm64: dts: n5x: drop invalid property and fix edac node name
arm64: dts: fsd: Add the MCT support
arm64: dts: stingray: Fix spi clock name
arm64: dts: ns2: Fix spi clock name
ARM: dts: rockchip: Update regulator name for PX3
ARM: dts: rockchip: Add #clock-cells value for rk805
arm64: dts: rockchip: Add #clock-cells value for rk805
arm64: dts: rockchip: Remove vcc13 and vcc14 for rk808
arm64: dts: rockchip: Fix SDIO regulator supply properties on rk3399-firefly
ARM: dts: at91: sama7g5: Add NAND support
ARM: dts: at91: sama7g5: add eic node
ARM: dts: at91: sama7g5: Remove unused properties in i2c nodes
ARM: dts: at91: sam9x60ek: modify vdd_1v5 regulator to vdd_1v15
arm64: dts: lg: align pl330 node name with dtschema
arm64: dts: lg: add dma-cells to pl330 node
arm64: dts: juno: align pl330 node name with dtschema
arm64: dts: broadcom: Fix sata nodename
arm64: dts: n5x: add sdr edac support
arm64: dts: agilex/stratix10: add clock-names to USB DWC2 node
dt-bindings: usb: dwc2: add disable-over-current
...
This contains a single, last-minute fix to disable the display SMMU by
default because under some circumstances leaving it enabled by default
can cause SMMU faults on boot.
-----BEGIN PGP SIGNATURE-----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=9uGD
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=qW8w
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.17-arm64-dt-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/fixes
arm64: tegra: Device tree fixes for v5.17
This contains a single, last-minute fix to disable the display SMMU by
default because under some circumstances leaving it enabled by default
can cause SMMU faults on boot.
* tag 'tegra-for-5.17-arm64-dt-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: tegra: Disable ISO SMMU for Tegra194
Link: https://lore.kernel.org/r/20220307182120.2169598-1-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The arm,armv8-pmuv3 compatible string is meant to be used only for
software models and not silicon chips. Drop them and use silicon-
specific compatible strings instead.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This commit enables USB device mode at J5 micro-B USB port of Jetson
Xavier NX.
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
On P3737 board, UART-A is available on 40-pin header. Enable UART-A for
P3737 and change the compatible string to "nvidia,tegra194-hsuart". This
allows supporting HW flow control and is the preferred choice for higher
baud rates.
Signed-off-by: kartik <kkartik@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add HDA device tree node for Tegra234 chip and for Jetson AGX Orin
platform.
Signed-off-by: Mohan Kumar <mkumard@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the '-@' DTC option for the Jetson TX1, Jetson Nano, Jetson TX2,
Jetson TX2 NX, Jetson AGX Xavier, Jetson Xavier NX and Jetson AGX Orin
platforms. This option populates the '__symbols__' node that contains
all the necessary symbols for supporting device-tree overlays on these
platforms. These Jetson platforms have various expansion headers,
including a 40-pin GPIO header, that allow various add-on modules to be
connected and this permits users to create device-tree overlays for
these modules.
Please note that this change does increase the size of the resulting DTB
from between 30-50%. For example, with v5.17-rc1 increase in size is as
follows:
tegra210-p2371-2180.dtb: 79580 -> 105744 bytes
tegra210-p3450-0000.dtb: 57465 -> 81357 bytes
tegra186-p2771-0000.dtb: 64763 -> 99553 bytes
tegra186-p3509-0000+p3636-0001.dtb: 48078 -> 62464 bytes
tegra194-p2972-0000.dtb: 75303 -> 111545 bytes
tegra194-p3509-0000+p3668-0000.dtb: 74762 -> 111995 bytes
tegra194-p3509-0000+p3668-0001.dtb: 74578 -> 111748 bytes
tegra234-p3737-0000+p3701-0000.dtb: 11229 -> 12917 bytes
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add audio-graph based sound card support on Jetson AGX Orin
platform. The sound card binds following modules:
* I/O interfaces such as I2S and DMIC (to be specific I2S1,
I2S2, I2S4, I2S6 and DMIC3 instances).
* HW accelerators such as MVC, SFC, AMX, ADX and Mixer (all
the available instances).
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add following devices which are part of APE subsystem
* ACONNECT, AGIC and ADMA
* AHUB and children (ADMAIF, I2S, DMIC, DSPK, MVC, SFC,
AMX, ADX and Mixer)
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The ADMAIF node represents the device that accesses memory in the Tegra
audio subsystem, so that's where the iommus and interconnects properties
should reside. Move them out of the sound card node and into the ADMAIF
node to properly reflect the memory data path.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The NVIDIA Tegra234 SoC comes with one single-instance ARM SMMU used by
isochronous memory clients and two dual-instance ARM SMMUs used by non-
isochronous memory clients.
Add the corresponding device tree nodes and hook up existing memory
clients (SDHCI and BPMP).
Signed-off-by: Thierry Reding <treding@nvidia.com>
Expose power, force-recovery and sleep buttons via a gpio-keys device so
that userspace can receive events from them.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add device tree node for GPCDMA controller on Tegra186 target
and Tegra194 target.
Signed-off-by: Rajesh Gumasta <rgumasta@nvidia.com>
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Commit e762232f94 ("arm64: tegra: Add ISO SMMU controller for Tegra194")
added the ISO SMMU for display devices on Tegra194. The SMMU is enabled by
default but not hooked up to the display controllers yet because we do not
have a way to pass frame-buffer memory from the bootloader to the kernel.
However, even though the SMMU is not hooked up to the display controllers'
SMMU faults are being seen if a display is connected. Therefore, keep the
ISO SMMU disabled by default for now.
Fixes: e762232f94 ("arm64: tegra: Add ISO SMMU controller for Tegra194")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
It's a relatively calm development cycle, but still lots of updates in
the driver side like Intel SOF. Below are some highlights:
* ALSA / ASoC core:
- A new kselftest for ALSA control API
- PCM NO_REWINDS support
- Potential race fixes around control removals
- Unify x86 SG-buffer memory allocation code
- Cleanups and race fixes for ASoC DPCM locking
* ASoC:
- Refinements and cleanups around the delay() APIs
- Wider use of dev_err_probe().
- Continuing cleanups and improvements to the SOF code
- Support for pin switches in simple-card derived cards
- Support for AMD Renoir ACP, Asahi Kasei Microdevices AKM4375, Intel
systems using NAU8825 and MAX98390, Mediatek MT8915, nVidia Tegra20
S/PDIF, Qualcomm systems using ALC5682I-VS and Texas Instruments
TLV320ADC3xxx
* HD-audio / USB-audio:
- Fix deadlock at HD-audio codec unbinding
- Fixes for Tegra194 HD-audio, new HDA support for CS35L41 codec
- Quirks for Lenovo and HP machines, Gigabyte mobo, Bose device
* Misc:
- Fix virmidi drain behavior
Note that the merge of CS35L41 codec support is still half-baked, and
at least one ACPI change is missing. Although this won't hinder the
kernel build itself, we're going to catch up before RC1.
-----BEGIN PGP SIGNATURE-----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=csTR
-----END PGP SIGNATURE-----
Merge tag 'sound-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"It's a relatively calm development cycle, but still lots of updates in
the driver side like Intel SOF. Below are some highlights:
ALSA / ASoC core:
- A new kselftest for ALSA control API
- PCM NO_REWINDS support
- Potential race fixes around control removals
- Unify x86 SG-buffer memory allocation code
- Cleanups and race fixes for ASoC DPCM locking
ASoC:
- Refinements and cleanups around the delay() APIs
- Wider use of dev_err_probe().
- Continuing cleanups and improvements to the SOF code
- Support for pin switches in simple-card derived cards
- Support for AMD Renoir ACP, Asahi Kasei Microdevices AKM4375, Intel
systems using NAU8825 and MAX98390, Mediatek MT8915, nVidia Tegra20
S/PDIF, Qualcomm systems using ALC5682I-VS and Texas Instruments
TLV320ADC3xxx
HD-audio / USB-audio:
- Fix deadlock at HD-audio codec unbinding
- Fixes for Tegra194 HD-audio, new HDA support for CS35L41 codec
- Quirks for Lenovo and HP machines, Gigabyte mobo, Bose device
Misc:
- Fix virmidi drain behavior
Note that the merge of CS35L41 codec support is still half-baked, and
at least one ACPI change is missing. Although this won't hinder the
kernel build itself, we're going to catch up before RC1"
* tag 'sound-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (415 commits)
ALSA: hda: intel-dsp-config: reorder the config table
ALSA: hda: intel-dsp-config: add JasperLake support
ALSA: hda: cs35l41: fix double free on error in probe()
ALSA: hda: Fix dependencies of CS35L41 on SPI/I2C buses
ALSA: hda: Fix dependency on ASoC cs35l41 codec
ASoC: cs35l41: Add support for hibernate memory retention mode
ASoC: cs35l41: Update handling of test key registers
ALSA: intel_hdmi: Check for error num after setting mask
ASoC: wcd9335: Keep a RX port value for each SLIM RX mux
ASoC: amd: acp: acp-mach: Change default RT1019 amp dev id
ALSA: virmidi: Remove duplicated code
ALSA: seq: virmidi: Add a drain operation
ASoC: topology: Fix typo
ASoC: fsl_asrc: refine the check of available clock divider
ASoC: Intel: bytcr_rt5640: Add support for external GPIO jack-detect
ASoC: Intel: bytcr_rt5640: Support retrieving the codec IRQ from the AMCR0F28 ACPI dev
ASoC: rt5640: Add support for boards with an external jack-detect GPIO
ASoC: rt5640: Allow snd_soc_component_set_jack() to override the codec IRQ
ASoC: rt5640: Change jack_work to a delayed_work
ASoC: rt5640: Fix possible NULL pointer deref on resume
...
Use the interconnects property to hook up the MMC and BPMP to the memory
controller. This is needed to set the correct bus-level DMA mask, which
is a prerequisite for adding IOMMU support.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This adds the memory controller and the embedded external memory
controller found on the Tegra234 SoC.
Signed-off-by: Thierry Reding <treding@nvidia.com>
DMA operations for the Tegra194 Video Image Compositor (VIC) are
coherent and so populate the 'dma-coherent' property.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Make the order of the clocks and clock-names properties match the order
in the device tree bindings. This isn't strictly necessary from a point
of view of the operating system because matching will be done based on
the clock-names, but it makes it easier to validate the device trees
against the DT schema.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add missing interrupts, clocks, clock-names, reset and reset-names
properties for the TSEC blocks found on Tegra210.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The XUSB pad controller handles the various PLL power supplies, so
remove any references to them from the PCIe and XUSB controller device
tree nodes.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The XUSB pad controller handles the various PLL power supplies, so
remove any references to them from the XUSB controller device tree
node.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The XUSB pad controller handles the various PLL power supplies, so
remove any references to them from the PCIe and XUSB controller device
tree nodes.
Signed-off-by: Thierry Reding <treding@nvidia.com>
GPIO hog nodes must have a "hog-" prefix or "-hog" suffix according to
the DT schema. Rename all such nodes to allow validation to pass.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Remove the unsupported "regulator-disable-ramp-delay" properties which
ended up in various DTS files for some reason.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The num-viewport property is never used and can be dropped, whereas the
"iommus" property is not needed since we use "iommu-map-mask" and
"iommu-map" already.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The HSP instances on Tegra194 are not fully compatible with the version
found on Tegra186, so drop the fallback compatible string from the list.
Signed-off-by: Thierry Reding <treding@nvidia.com>
