Pinmux node names should have a pinmux- prefix and not use underscores.
Fix up some cases that didn't follow those rules.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Tegra QSPI controllers use a single reset control, so reset-names is
not necessary and therefore not specified in the DT bindings. Drop the
property from device tree files to avoid validation warnings.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Tegra234 HDA controller is not backwards-compatible with Tegra30, so
drop the corresponding compatible string from the list.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Tegra194 HDA controller is not backwards-compatible with Tegra30, so
drop the corresponding compatible string from the list.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Instead of using the deprecated vbus-gpio property, switch to using the
more standard vbus-gpios property.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The PMC pinmux configuration nodes need to be part of a top-level pinmux
node. Add that new "pinmux" node and move the configuration nodes into
it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DeviceTree Specification v0.3 specifies that the cache node
'compatible' and 'cache-level' properties are 'required'. Cf.
s3.8 Multi-level and Shared Cache Nodes
The 'cache-unified' property should be present if one of the
properties for unified cache is present ('cache-size', ...).
Update the Device Trees accordingly.
Signed-off-by: Pierre Gondois <pierre.gondois@arm.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The 'enable-active-low' property is not a valid one.
Only 'enable-active-high' is valid, and when this property is absent
the gpio regulator will act as active low by default.
Remove the invalid 'enable-active-low' property.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add dma-channel-mask property in Tegra GPCDMA device tree node.
The property would help to specify the channels to be used in
kernel and reserve few for the firmware. This was previously
achieved by limiting the channel number to 31 in the driver.
This is wrong and does not align with the hardware. Correct this
and update the interrupts property to list all 32 interrupts.
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
According to the DT schema in usb-device.yaml, each USB device node
needs a compatible string, so add one for the built-in USB Ethernet
device on Jetson TX1.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The registers for the AON pinmux reside in a partition different from
the registers for the main pinmux. Instead of treating them as one and
the same device, split them up so that they are each their own devices.
Also add gpio-ranges properties to the corresponding GPIO controllers
such that the pinmux and GPIO controllers can be paired up properly.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the ECAM aperture information for all the PCIe controllers of
Tegra234.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Tegra PWFM controllers use a single clock, so there's no need for a
clock-names property.
Suggested-by: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Tegra Combined UART (TCU) is the default serial interface for Jetson
Xavier and Orin platforms and so update the bootargs for these platforms
to use the TCU.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Enable additional PWM controllers in device tree so that the PWM pins on
the Jetson AGX Orin Developer Kit 40-pin header can be used.
Signed-off-by: Sandipan Patra <spatra@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The P2U nodes that were recently added were not added in the correct
order. Sort them in the right place by unit-address.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Populate the SBSA UART for Tegra234 and enable this UART for Jetson AGX
Orin.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the PWM fan node for the Tegra234 Jetson AGX Orin platform.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Populate all the PWM devices for Tegra234. Finally, update the
compatible string for the existing 'pwm1' node to just be 'tegra194-pwm'
and remove the fallback to 'tegra186-pwm', which aligns with the
binding documentation.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Commit 156af9de09 ("arm64: tegra: Add Tegra234 I2C devicetree nodes")
populated the I2C device nodes for Tegra234. One of these nodes
contains the property 'nvidia,hw-instance-id' which is neither
documented or used. Remove this unused property.
Fixes: 156af9de09 ("arm64: tegra: Add Tegra234 I2C devicetree nodes")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
commit edf408b946 ("PCI: dwc: Validate iATU outbound mappings against
hardware constraints") exposes an issue with the existing partitioning of
the aperture space where the Prefetchable apertures of controllers
C5, C7 and C9 in Tegra234 cross the 32GB boundary hardware constraint.
This patch makes sure that the Prefetchable region doesn't spill over
the 32GB boundary.
Fixes: ec142c44b0 ("arm64: tegra: Add P2U and PCIe controller nodes to Tegra234 DT")
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add a device tree node for NVDEC on Tegra234.
Booting the firmware requires some information regarding offsets
within the firmware binary. These are passed through the device
tree, but since the values vary depending on the firmware version,
and the firmware itself is not available to the OS, the flasher is
expected to provide a device tree overlay with values corresponding
to the firmware it is flashing. The overlay then replaces the
placeholder values here.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The currently specified 'ranges' properties don't actually include
all devices under the host1x bus on Tegra194 and Tegra234. Expand
them appropriately.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add dma properties to support GPCDMA for I2C in Tegra 186 and later
chips
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the iommus property to the HDA node on Tegra234.
Signed-off-by: Mohan Kumar <mkumard@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add Host1x context isolation domains on Tegra234. On Tegra234 we have
two IOMMUs that are connected to Host1x-channel programmed engines,
so we have to include domains for each of them.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Make sure that each phandle-array is enclosed in a set of angular
brackets and properly indent each entry.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Google Pixel C contains a BRCM4354 Wi-Fi + BT module.
Add a DT node for its Wi-Fi functionality. Tested on Pixel C.
Signed-off-by: Diogo Ivo <diogo.ivo@tecnico.ulisboa.pt>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Google Pixel C contains a BRCM4354 Wi-Fi + BT module.
Add a DT node for its BT functionality. Tested on Pixel C.
Signed-off-by: Diogo Ivo <diogo.ivo@tecnico.ulisboa.pt>
Signed-off-by: Thierry Reding <treding@nvidia.com>
A Multi-Gigabit Ethernet (MGBE) instance drives the primary Ethernet
port on the Jetson AGX Orin Developer Kit. Enable it.
Signed-off-by: Bhadram Varka <vbhadram@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add device tree nodes for the four instances of the Multi-Gigabit
Ethernet (MGBE) IP found on NVIDIA Tegra234 SoCs.
Signed-off-by: Bhadram Varka <vbhadram@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
There is no need to list the Tegra194-specific compatible for Tegra234
because the backwards-compatibility goes back all the way to Tegra186.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Hook SDMMC1 CD up with CVM GPIO02 (SOC_GPIO11) used for card detection on J4
(uSD socket) on the carrier.
Fixes: ef633bfc21 ("arm64: tegra: Enable card detect for SD card on P2888")
Signed-off-by: Tamás Szűcs <tszucs@protonmail.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use the compatible specific to Tegra234 for GPCDMA to support
additional features.
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add device tree nodes for Host1x and VIC on Tegra234.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add Host1x context stream IDs on systems that support Host1x context
isolation. Host1x and attached engines can use these stream IDs to
allow isolation between memory used by different processes.
The specified stream IDs must match those configured by the hypervisor,
if one is present.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The native timers IP block found on NVIDIA Tegra SoCs implements a
watchdog timer that can be used to recover from system hangs. Add and
enable the device tree node on Tegra234.
Signed-off-by: Kartik <kkartik@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The native timers IP block found on NVIDIA Tegra SoCs implements a
watchdog timer that can be used to recover from system hangs. Add and
enable the device tree node on Tegra194.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Kartik <kkartik@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Enable the native timers on Tegra186 chips to allow using the watchdog
functionality to recover from system hangs.
Signed-off-by: Kartik <kkartik@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra234 uses the Control Backbone (CBB) version 2.0. Add the nodes
that enable error handling from the various CBB 2.0 fabrics found on
Tegra234.
Signed-off-by: Sumit Gupta <sumitg@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add device tree nodes to enable error handling on the Control Backbone
(CBB). Tegra194 uses CBB version 1.0.
Signed-off-by: Sumit Gupta <sumitg@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The node names should be generic and DT schema expects certain pattern
(e.g. with key/button/switch).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Tegra SYSRAM contains regions access to which is restricted to
certain hardware blocks on the system, and speculative accesses to
those will cause issues.
Patch 'misc: sram: Only map reserved areas in Tegra SYSRAM' attempted
to resolve this by only mapping the regions specified in the device
tree on the assumption that there are no such restricted areas within
the 64K-aligned area of memory that contains the memory we wish to map.
Turns out this assumption is wrong, as there are such areas above the
4K pages described in the device trees. As such, we need to use the
bigger hammer that is no-memory-wc, which causes the memory to be
mapped as Device memory to which speculative accesses are disallowed.
As such, the previous patch in the series,
'firmware: tegra: bpmp: do only aligned access to IPC memory area',
is required with this patch to make the BPMP driver only issue aligned
memory accesses as those are also required with Device memory.
Fixes: fec29bf049 ("misc: sram: Only map reserved areas in Tegra SYSRAM")
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Reviewed-by: Yousaf Kaukab <ykaukab@suse.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add device tree nodes for Tegra234 GPCDMA
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Fix whitespace coding style: use single space instead of tabs or
multiple spaces around '=' sign in property assignment. No functional
changes (same DTB).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Enable OPE module usage on various Jetson platforms. This can be plugged
into an audio path using ALSA mixer controls. Add audio-graph-port binding
to use OPE device with generic audio-graph based sound card.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Output Processing Engine (OPE) is a client of AHUB and is present on
Tegra210 and later generations of Tegra SoC. Add this device on the
relevant SoC DTSI files.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Commit 4782c0a5dd ("clk: tegra: Don't deassert reset on enabling
clocks") removed deassertion of reset lines when enabling peripheral
clocks. This breaks the initialization of the DFLL driver which relied
on this behaviour.
In order to be able to fix this, add the corresponding reset to the DT.
Tested on Google Pixel C.
Cc: stable@vger.kernel.org
Fixes: 4782c0a5dd ("clk: tegra: Don't deassert reset on enabling clocks")
Signed-off-by: Diogo Ivo <diogo.ivo@tecnico.ulisboa.pt>
Signed-off-by: Thierry Reding <treding@nvidia.com>
From tegra186 onwards, memory controller support multiple channels.
During the error interrupts from memory controller, corresponding
channels need to be accessed for logging error info and clearing the
interrupt.
So add address and size of these channels in device tree node of
tegra186, tegra194 and tegra234 memory controller. Also add reg-names
for each of these reg items which are used by driver for mapping.
Signed-off-by: Ashish Mhetre <amhetre@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Enable ASRC module usage on various Jetson Platforms. This can be plugged
into an audio path using ALSA mixer controls.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Asynchronous Sample Rate Converter (ASRC) is a client of AHUB and is
present on Tegra186 and later generations of Tegra SoC. Add this device
on the relevant SoC DTSI files.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
According to the device-tree binding document for PWM fans [0], the
PWM fan node name should be 'pwm-fan'. Update the PWM fan node name to
align with this.
[0] Documentation/devicetree/bindings/hwmon/pwm-fan.txt
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Adding CCPLEX cluster node to represent Tegra234 cpufreq. Tegra234 uses
some of the CRAB (Control Register Access Bus) registers for CPU
frequency requests. These registers are memory mapped to the
CCPLEX_MMCRAB_ARM region. In this node, mapping the range of MMCRAB
registers is required only for CPU frequency info.
Signed-off-by: Sumit Gupta <sumitg@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This adds the QSPI controllers on the Tegra234 SoC and populates the
SPI NOR flash device for the Jetson AGX Orin platform.
Signed-off-by: Ashish Singhal <ashishsingha@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The default parent for SDMMC1/3 clock sources can provide maximum frequency
of 136MHz for SDR104 mode.
Update parent clock source for SDMMC1/SDMMC3 instances
to increase the output clock frequency to 195MHz and improve the perf.
Signed-off-by: Aniruddha Rao <anrao@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
After a somewhat quiet 5.17 release, the size of the DT changes
is a bit larger again. There are nine new SoC that get added,
all of them related to existing platforms:
- Airoha (formerly Mediatek/EcoNet) EN7523 networking SoC and EVB
- Mediatek mt6582 tablet platform with the Prestigio PMT5008 3G tablet
- Microchip Lan966 networking SoC and it evaluation board
- Qualcomm Snapdragon 625/632 midrange phone SoCs, with the
LG Nexus 5X and Fairphone FP3 phones
- Renesas RZ/G2LC and RZ/V2L general-purpose embedded SoCs,
along with their evaluation boards
- Samsung Exynos 850 phone SoC and reference board
- Samsung Exynos7885 with the Samsung Galaxy A8 (2018) phone
- Tesla FSD (Fully Self-Driving), an automotive SoC losely derived
from the Samsung Exynos family.
- TI K3/AM62 SoC and reference board
Support for additional functionality in existing dts files is added all
over the place: Samsung, Renesas, Mstar, wpcm450, OMAP, AT91, Allwinner,
i.MX, Tegra, Aspeed, Oxnas, Qualcomm, Mediatek, and Broadcom.
Samsung has a rework for its pinctrl schema that is a bit tricky and
requires driver changes to be included here.
A few more platforms only have smaller cleanups and DT Schema fixes,
this includes SoCFPGA, ux500, ixp4xx, STi, Xilinx Zynq, LG, and Juno.
The new machines are really too many to list, but I'll do it anyway:
Allwinner:
- A20-Marsboard development board
Amlogic
- Amediatek X96-AIR (Amlogic S905X3)
- CYX A95XF3-AIR (Amlogic S905X3)
- Haochuangy H96-Max (Amlogic S905X3)
- Amlogic AQ222 (Amlogic S4)
- OSMC Vero 4K+ (Amlogic S905D)
Arm Juno
- Separate DT depending on SCMI firmware version
Aspeed:
- Quanta S6Q BMC (AST2600)
- ASRock ROMED8HM3 (AST2500)
Broadcom:
- Raspberry Pi Zero 2 W
Marvell MVEBU/Armada:
- Ctera C200 V1 NAS (kirkwood)
- Ctera C200 V2 NAS (armada-370)
Mstar
- DongShanPiOne, a low-end embedded board
- Miyoo Mini handheld game console
NXP i.MX:
- Numerous i.MX8M Mini based boards in even more variations, but
none based on other SoCs this time:
Protonic PRT8MM, emCON-MX8M Mini, Toradex Verdin, and
Gateworks GW7903
Qualcomm:
- Google Herobrine R1 Chromebook platform (Snapdragon 7c Gen 3)
- SHIFT6mq phone (Snapdragon 845)
- Samsung Galaxy Book2 (Snapdragon 850)
- Snapdragon 8 Gen 1 Hardware Development Kit
TI OMAP:
- SanCloud BeagleBone Enhanced WiFi
Rockchip:
- Pine64 PineNote ereader tablet (rk356x)
- Bananapi-R2-Pro (rk356x)
STM32:
- emtrion emSBS-Argon embedded board (stm32mp157c)
-----BEGIN PGP SIGNATURE-----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=v98T
-----END PGP SIGNATURE-----
Merge tag 'arm-dt-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM devicetree updates from Arnd Bergmann:
"After a somewhat quiet 5.17 release, the size of the DT changes is a
bit larger again. There are nine new SoC that get added, all of them
related to existing platforms:
- Airoha (formerly Mediatek/EcoNet) EN7523 networking SoC and EVB
- Mediatek mt6582 tablet platform with the Prestigio PMT5008 3G
tablet
- Microchip Lan966 networking SoC and it evaluation board
- Qualcomm Snapdragon 625/632 midrange phone SoCs, with the LG Nexus
5X and Fairphone FP3 phones
- Renesas RZ/G2LC and RZ/V2L general-purpose embedded SoCs, along
with their evaluation boards
- Samsung Exynos 850 phone SoC and reference board
- Samsung Exynos7885 with the Samsung Galaxy A8 (2018) phone
- Tesla FSD (Fully Self-Driving), an automotive SoC loosely derived
from the Samsung Exynos family.
- TI K3/AM62 SoC and reference board
Support for additional functionality in existing dts files is added
all over the place: Samsung, Renesas, Mstar, wpcm450, OMAP, AT91,
Allwinner, i.MX, Tegra, Aspeed, Oxnas, Qualcomm, Mediatek, and
Broadcom.
Samsung has a rework for its pinctrl schema that is a bit tricky and
requires driver changes to be included here.
A few more platforms only have smaller cleanups and DT Schema fixes,
this includes SoCFPGA, ux500, ixp4xx, STi, Xilinx Zynq, LG, and Juno.
The new machines are really too many to list, but I'll do it anyway:
Allwinner:
- A20-Marsboard development board
Amlogic:
- Amediatek X96-AIR (Amlogic S905X3)
- CYX A95XF3-AIR (Amlogic S905X3)
- Haochuangy H96-Max (Amlogic S905X3)
- Amlogic AQ222 (Amlogic S4)
- OSMC Vero 4K+ (Amlogic S905D)
Arm Juno:
- Separate DT depending on SCMI firmware version
Aspeed:
- Quanta S6Q BMC (AST2600)
- ASRock ROMED8HM3 (AST2500)
Broadcom:
- Raspberry Pi Zero 2 W
Marvell MVEBU/Armada:
- Ctera C200 V1 NAS (kirkwood)
- Ctera C200 V2 NAS (armada-370)
Mstar:
- DongShanPiOne, a low-end embedded board
- Miyoo Mini handheld game console
NXP i.MX:
- Numerous i.MX8M Mini based boards in even more variations, but
none based on other SoCs this time:
Protonic PRT8MM, emCON-MX8M Mini, Toradex Verdin, and
Gateworks GW7903
Qualcomm:
- Google Herobrine R1 Chromebook platform (Snapdragon 7c Gen 3)
- SHIFT6mq phone (Snapdragon 845)
- Samsung Galaxy Book2 (Snapdragon 850)
- Snapdragon 8 Gen 1 Hardware Development Kit
TI OMAP:
- SanCloud BeagleBone Enhanced WiFi
Rockchip:
- Pine64 PineNote ereader tablet (rk356x)
- Bananapi-R2-Pro (rk356x)
STM32:
- emtrion emSBS-Argon embedded board (stm32mp157c)"
* tag 'arm-dt-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (627 commits)
arm64: dts: n5x: drop invalid property and fix edac node name
arm64: dts: fsd: Add the MCT support
arm64: dts: stingray: Fix spi clock name
arm64: dts: ns2: Fix spi clock name
ARM: dts: rockchip: Update regulator name for PX3
ARM: dts: rockchip: Add #clock-cells value for rk805
arm64: dts: rockchip: Add #clock-cells value for rk805
arm64: dts: rockchip: Remove vcc13 and vcc14 for rk808
arm64: dts: rockchip: Fix SDIO regulator supply properties on rk3399-firefly
ARM: dts: at91: sama7g5: Add NAND support
ARM: dts: at91: sama7g5: add eic node
ARM: dts: at91: sama7g5: Remove unused properties in i2c nodes
ARM: dts: at91: sam9x60ek: modify vdd_1v5 regulator to vdd_1v15
arm64: dts: lg: align pl330 node name with dtschema
arm64: dts: lg: add dma-cells to pl330 node
arm64: dts: juno: align pl330 node name with dtschema
arm64: dts: broadcom: Fix sata nodename
arm64: dts: n5x: add sdr edac support
arm64: dts: agilex/stratix10: add clock-names to USB DWC2 node
dt-bindings: usb: dwc2: add disable-over-current
...
This contains a single, last-minute fix to disable the display SMMU by
default because under some circumstances leaving it enabled by default
can cause SMMU faults on boot.
-----BEGIN PGP SIGNATURE-----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=9uGD
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=qW8w
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.17-arm64-dt-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/fixes
arm64: tegra: Device tree fixes for v5.17
This contains a single, last-minute fix to disable the display SMMU by
default because under some circumstances leaving it enabled by default
can cause SMMU faults on boot.
* tag 'tegra-for-5.17-arm64-dt-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: tegra: Disable ISO SMMU for Tegra194
Link: https://lore.kernel.org/r/20220307182120.2169598-1-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The arm,armv8-pmuv3 compatible string is meant to be used only for
software models and not silicon chips. Drop them and use silicon-
specific compatible strings instead.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This commit enables USB device mode at J5 micro-B USB port of Jetson
Xavier NX.
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
On P3737 board, UART-A is available on 40-pin header. Enable UART-A for
P3737 and change the compatible string to "nvidia,tegra194-hsuart". This
allows supporting HW flow control and is the preferred choice for higher
baud rates.
Signed-off-by: kartik <kkartik@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add HDA device tree node for Tegra234 chip and for Jetson AGX Orin
platform.
Signed-off-by: Mohan Kumar <mkumard@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the '-@' DTC option for the Jetson TX1, Jetson Nano, Jetson TX2,
Jetson TX2 NX, Jetson AGX Xavier, Jetson Xavier NX and Jetson AGX Orin
platforms. This option populates the '__symbols__' node that contains
all the necessary symbols for supporting device-tree overlays on these
platforms. These Jetson platforms have various expansion headers,
including a 40-pin GPIO header, that allow various add-on modules to be
connected and this permits users to create device-tree overlays for
these modules.
Please note that this change does increase the size of the resulting DTB
from between 30-50%. For example, with v5.17-rc1 increase in size is as
follows:
tegra210-p2371-2180.dtb: 79580 -> 105744 bytes
tegra210-p3450-0000.dtb: 57465 -> 81357 bytes
tegra186-p2771-0000.dtb: 64763 -> 99553 bytes
tegra186-p3509-0000+p3636-0001.dtb: 48078 -> 62464 bytes
tegra194-p2972-0000.dtb: 75303 -> 111545 bytes
tegra194-p3509-0000+p3668-0000.dtb: 74762 -> 111995 bytes
tegra194-p3509-0000+p3668-0001.dtb: 74578 -> 111748 bytes
tegra234-p3737-0000+p3701-0000.dtb: 11229 -> 12917 bytes
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add audio-graph based sound card support on Jetson AGX Orin
platform. The sound card binds following modules:
* I/O interfaces such as I2S and DMIC (to be specific I2S1,
I2S2, I2S4, I2S6 and DMIC3 instances).
* HW accelerators such as MVC, SFC, AMX, ADX and Mixer (all
the available instances).
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add following devices which are part of APE subsystem
* ACONNECT, AGIC and ADMA
* AHUB and children (ADMAIF, I2S, DMIC, DSPK, MVC, SFC,
AMX, ADX and Mixer)
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The ADMAIF node represents the device that accesses memory in the Tegra
audio subsystem, so that's where the iommus and interconnects properties
should reside. Move them out of the sound card node and into the ADMAIF
node to properly reflect the memory data path.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The NVIDIA Tegra234 SoC comes with one single-instance ARM SMMU used by
isochronous memory clients and two dual-instance ARM SMMUs used by non-
isochronous memory clients.
Add the corresponding device tree nodes and hook up existing memory
clients (SDHCI and BPMP).
Signed-off-by: Thierry Reding <treding@nvidia.com>
Expose power, force-recovery and sleep buttons via a gpio-keys device so
that userspace can receive events from them.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add device tree node for GPCDMA controller on Tegra186 target
and Tegra194 target.
Signed-off-by: Rajesh Gumasta <rgumasta@nvidia.com>
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Commit e762232f94 ("arm64: tegra: Add ISO SMMU controller for Tegra194")
added the ISO SMMU for display devices on Tegra194. The SMMU is enabled by
default but not hooked up to the display controllers yet because we do not
have a way to pass frame-buffer memory from the bootloader to the kernel.
However, even though the SMMU is not hooked up to the display controllers'
SMMU faults are being seen if a display is connected. Therefore, keep the
ISO SMMU disabled by default for now.
Fixes: e762232f94 ("arm64: tegra: Add ISO SMMU controller for Tegra194")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
It's a relatively calm development cycle, but still lots of updates in
the driver side like Intel SOF. Below are some highlights:
* ALSA / ASoC core:
- A new kselftest for ALSA control API
- PCM NO_REWINDS support
- Potential race fixes around control removals
- Unify x86 SG-buffer memory allocation code
- Cleanups and race fixes for ASoC DPCM locking
* ASoC:
- Refinements and cleanups around the delay() APIs
- Wider use of dev_err_probe().
- Continuing cleanups and improvements to the SOF code
- Support for pin switches in simple-card derived cards
- Support for AMD Renoir ACP, Asahi Kasei Microdevices AKM4375, Intel
systems using NAU8825 and MAX98390, Mediatek MT8915, nVidia Tegra20
S/PDIF, Qualcomm systems using ALC5682I-VS and Texas Instruments
TLV320ADC3xxx
* HD-audio / USB-audio:
- Fix deadlock at HD-audio codec unbinding
- Fixes for Tegra194 HD-audio, new HDA support for CS35L41 codec
- Quirks for Lenovo and HP machines, Gigabyte mobo, Bose device
* Misc:
- Fix virmidi drain behavior
Note that the merge of CS35L41 codec support is still half-baked, and
at least one ACPI change is missing. Although this won't hinder the
kernel build itself, we're going to catch up before RC1.
-----BEGIN PGP SIGNATURE-----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=csTR
-----END PGP SIGNATURE-----
Merge tag 'sound-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"It's a relatively calm development cycle, but still lots of updates in
the driver side like Intel SOF. Below are some highlights:
ALSA / ASoC core:
- A new kselftest for ALSA control API
- PCM NO_REWINDS support
- Potential race fixes around control removals
- Unify x86 SG-buffer memory allocation code
- Cleanups and race fixes for ASoC DPCM locking
ASoC:
- Refinements and cleanups around the delay() APIs
- Wider use of dev_err_probe().
- Continuing cleanups and improvements to the SOF code
- Support for pin switches in simple-card derived cards
- Support for AMD Renoir ACP, Asahi Kasei Microdevices AKM4375, Intel
systems using NAU8825 and MAX98390, Mediatek MT8915, nVidia Tegra20
S/PDIF, Qualcomm systems using ALC5682I-VS and Texas Instruments
TLV320ADC3xxx
HD-audio / USB-audio:
- Fix deadlock at HD-audio codec unbinding
- Fixes for Tegra194 HD-audio, new HDA support for CS35L41 codec
- Quirks for Lenovo and HP machines, Gigabyte mobo, Bose device
Misc:
- Fix virmidi drain behavior
Note that the merge of CS35L41 codec support is still half-baked, and
at least one ACPI change is missing. Although this won't hinder the
kernel build itself, we're going to catch up before RC1"
* tag 'sound-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (415 commits)
ALSA: hda: intel-dsp-config: reorder the config table
ALSA: hda: intel-dsp-config: add JasperLake support
ALSA: hda: cs35l41: fix double free on error in probe()
ALSA: hda: Fix dependencies of CS35L41 on SPI/I2C buses
ALSA: hda: Fix dependency on ASoC cs35l41 codec
ASoC: cs35l41: Add support for hibernate memory retention mode
ASoC: cs35l41: Update handling of test key registers
ALSA: intel_hdmi: Check for error num after setting mask
ASoC: wcd9335: Keep a RX port value for each SLIM RX mux
ASoC: amd: acp: acp-mach: Change default RT1019 amp dev id
ALSA: virmidi: Remove duplicated code
ALSA: seq: virmidi: Add a drain operation
ASoC: topology: Fix typo
ASoC: fsl_asrc: refine the check of available clock divider
ASoC: Intel: bytcr_rt5640: Add support for external GPIO jack-detect
ASoC: Intel: bytcr_rt5640: Support retrieving the codec IRQ from the AMCR0F28 ACPI dev
ASoC: rt5640: Add support for boards with an external jack-detect GPIO
ASoC: rt5640: Allow snd_soc_component_set_jack() to override the codec IRQ
ASoC: rt5640: Change jack_work to a delayed_work
ASoC: rt5640: Fix possible NULL pointer deref on resume
...
Use the interconnects property to hook up the MMC and BPMP to the memory
controller. This is needed to set the correct bus-level DMA mask, which
is a prerequisite for adding IOMMU support.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This adds the memory controller and the embedded external memory
controller found on the Tegra234 SoC.
Signed-off-by: Thierry Reding <treding@nvidia.com>
DMA operations for the Tegra194 Video Image Compositor (VIC) are
coherent and so populate the 'dma-coherent' property.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Make the order of the clocks and clock-names properties match the order
in the device tree bindings. This isn't strictly necessary from a point
of view of the operating system because matching will be done based on
the clock-names, but it makes it easier to validate the device trees
against the DT schema.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add missing interrupts, clocks, clock-names, reset and reset-names
properties for the TSEC blocks found on Tegra210.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The XUSB pad controller handles the various PLL power supplies, so
remove any references to them from the PCIe and XUSB controller device
tree nodes.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The XUSB pad controller handles the various PLL power supplies, so
remove any references to them from the XUSB controller device tree
node.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The XUSB pad controller handles the various PLL power supplies, so
remove any references to them from the PCIe and XUSB controller device
tree nodes.
Signed-off-by: Thierry Reding <treding@nvidia.com>
GPIO hog nodes must have a "hog-" prefix or "-hog" suffix according to
the DT schema. Rename all such nodes to allow validation to pass.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Remove the unsupported "regulator-disable-ramp-delay" properties which
ended up in various DTS files for some reason.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The num-viewport property is never used and can be dropped, whereas the
"iommus" property is not needed since we use "iommu-map-mask" and
"iommu-map" already.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The HSP instances on Tegra194 are not fully compatible with the version
found on Tegra186, so drop the fallback compatible string from the list.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Tegra194 pinmux DT bindings do not define the nvidia,lpdr property,
so drop them from the device trees that have listed them.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The standard "jedec," vendor prefix should be used for SPI NOR flash
chips. This allows the right DT schema to be picked for validation.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Tegra186 CCPLEX cluster register region is 4 MiB is length, not 4
MiB - 1. This was likely presumed to be the "limit" rather than length.
Fix it up.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The I2C controller found on Tegra186 is not fully compatible with the
Tegra210 version, so drop the fallback compatible string from the list.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Child nodes of the TI INA3221 power monitor device tree node should be
called input@* according to the DT schema.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DT schema requires that nodes representing thermal zones include a
"-thermal" suffix in their name.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Make the order of the clocks and clock-names properties match the order
in the device tree bindings. This isn't strictly necessary from a point
of view of the operating system because matching will be done based on
the clock-names, but it makes it easier to validate the device trees
against the DT schema.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The CML1 and PLL_E clocks are never explicitly used by the AHCI
controller found on Tegra132, so drop them from the corresponding device
tree node.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The I2C controller found on Tegra124 is not fully compatible with the
Tegra114 version, so drop the fallback compatible string from the list.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add peripheral OPP tables on Tegra132 and wire them up to ACTMON and the
EMC. While at it, add the missing "#interconnect-cells" properties to
the memory controller and external memory controller nodes. Also set the
"#reset-cells" property for the memory controller because it exports the
hotflush reset controls.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The TKE (time-keeping engine) found on Tegra132 is not backwards
compatible with the version found on Tegra20, so update the compatible
string list accordingly.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Tegra PMC device tree bindings don't support the "#wake-cells" and
"nvidia,reset-gpio" properties, so remove them.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The AS3722 pinmux device tree node doesn't have a "reg" property and
therefore must not have a unit-address, so drop it.
While at it, add missing unit-addresses for the charger and smart
battery IC's on the ChromeOS embedded controller's I2C tunnel bus.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The native timers IP block found on NVIDIA Tegra SoCs implements a
watchdog timer that can be used to recover from system hangs. Add the
device tree node on Tegra186.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Regulators defined at the top level in device tree are no longer part of
a simple bus and therefore don't have a reg property. Nodes without a
reg property shouldn't have a unit-address either, so drop the unit
address from the node names. To ensure nodes aren't duplicated (in which
case they would end up merged in the final DTB), append the name of the
regulator to the node name.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Clocks defined at the top level in device tree are no longer part of a
simple bus and therefore don't have a reg property. Nodes without a reg
property shouldn't have a unit-address either, so drop the unit address
from the node names. To ensure nodes aren't duplicated (in which case
they would end up merged in the final DTB), append the name of the clock
to the node name.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The display controllers are attached to a separate ARM SMMU instance
that is dedicated to servicing isochronous memory clients. Add this ISO
instance of the ARM SMMU to device tree.
Please note that the display controllers are not hooked up to this SMMU
yet, because we are still missing a means to transition framebuffers
used by the bootloader to the kernel.
This based upon an initial patch by Thierry Reding <treding@nvidia.com>.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Populate the device-tree nodes for NVENC and NVJPG Host1x engines on
Tegra186 and Tegra194.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add support to enumerate SD in UHS mode on Tegra194. Add required
device-tree properties in SDMMC1 and SDMMC3 instances to enable dynamic
pad voltage switching and enumerate SD card in UHS-I modes.
Signed-off-by: Prathamesh Shete <pshete@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Jetson AGX Orin Developer Kit is a continuation of the Jetson
Developer Kit line using the new NVIDIA Tegra234 (Orin) SoC.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The NVIDIA Tegra234 SoC has 3 clusters of 4 Cortex-A78AE CPU cores each,
for a total of 12 CPUs. Each CPU has 64 KiB instruction and data caches
with each cluster having an additional 256 KiB unified L2 cache and a 2
MiB L3 cache.
Signed-off-by: Thierry Reding <treding@nvidia.com>
These two controllers expose general purpose I/O pins that can be used
to control or monitor a variety of signals.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add a device for TCU (Tegra Combined UART) used for serial console.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add missing properties to the eMMC controller, as required to use it on
actual hardware.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
On final Tegra234 systems, shared memory for communication with BPMP is
located at offset 0x70000 in SYSRAM.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The json-schema bindings for SRAM expect the nodes to be called "sram"
rather than "sysram" or "shmem". Furthermore, place the brackets around
the SYSRAM references such that a two-element array is created rather
than a two-element array nested in a single-element array. This is not
relevant for device tree itself, but allows the nodes to be properly
validated against json-schema bindings.
Signed-off-by: Thierry Reding <treding@nvidia.com>
As defined by Documentation/devicetree/bindings/pci/pci-ep.yaml,
PCIe endpoints match this pattern:
properties:
$nodename:
pattern: "^pcie-ep@"
Change the existing ones in order to avoid those warnings:
arch/arm64/boot/dts/nvidia/tegra194-p3509-0000+p3668-0001.dt.yaml: pcie_ep@14160000: $nodename:0: 'pcie_ep@14160000' does not match '^pcie-ep@'
From schema: Documentation/devicetree/bindings/pci/snps,dw-pcie-ep.yaml
arch/arm64/boot/dts/nvidia/tegra194-p3509-0000+p3668-0001.dt.yaml: pcie_ep@14180000: $nodename:0: 'pcie_ep@14180000' does not match '^pcie-ep@'
From schema: Documentation/devicetree/bindings/pci/snps,dw-pcie-ep.yaml
arch/arm64/boot/dts/nvidia/tegra194-p3509-0000+p3668-0001.dt.yaml: pcie_ep@141a0000: $nodename:0: 'pcie_ep@141a0000' does not match '^pcie-ep@'
From schema: Documentation/devicetree/bindings/pci/snps,dw-pcie-ep.yaml
arch/arm64/boot/dts/nvidia/tegra194-p3509-0000+p3668-0000.dt.yaml: pcie_ep@14160000: $nodename:0: 'pcie_ep@14160000' does not match '^pcie-ep@'
From schema: Documentation/devicetree/bindings/pci/snps,dw-pcie-ep.yaml
arch/arm64/boot/dts/nvidia/tegra194-p3509-0000+p3668-0000.dt.yaml: pcie_ep@14180000: $nodename:0: 'pcie_ep@14180000' does not match '^pcie-ep@'
From schema: Documentation/devicetree/bindings/pci/snps,dw-pcie-ep.yaml
arch/arm64/boot/dts/nvidia/tegra194-p3509-0000+p3668-0000.dt.yaml: pcie_ep@141a0000: $nodename:0: 'pcie_ep@141a0000' does not match '^pcie-ep@'
From schema: Documentation/devicetree/bindings/pci/snps,dw-pcie-ep.yaml
arch/arm64/boot/dts/nvidia/tegra194-p2972-0000.dt.yaml: pcie_ep@14160000: $nodename:0: 'pcie_ep@14160000' does not match '^pcie-ep@'
From schema: Documentation/devicetree/bindings/pci/snps,dw-pcie-ep.yaml
arch/arm64/boot/dts/nvidia/tegra194-p2972-0000.dt.yaml: pcie_ep@14180000: $nodename:0: 'pcie_ep@14180000' does not match '^pcie-ep@'
From schema: Documentation/devicetree/bindings/pci/snps,dw-pcie-ep.yaml
arch/arm64/boot/dts/nvidia/tegra194-p2972-0000.dt.yaml: pcie_ep@141a0000: $nodename:0: 'pcie_ep@141a0000' does not match '^pcie-ep@'
From schema: Documentation/devicetree/bindings/pci/snps,dw-pcie-ep.yaml
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
There's no such thing as a generic USB EHCI controller. The EHCI
controllers found on Tegra SoCs are instantiations that need Tegra-
specific glue to work properly, so drop the generic compatible string
and keep only the Tegra-specific ones.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Extend APE audio support by adding more audio components such as SFC,
MVC, AMX, ADX and Mixer. These components can be plugged into an audio
path and required processing can be done. ASoC audio-graph based sound
driver is used to facilitate this and thus extend sound bindings as
well.
The components in the path may require different PCM parameters (such
as sample rate, channels or sample size). Depending on the pre-defined
audio paths, these can be statically configured with "convert-xxx" DT
properties in endpoint subnode. The support for the rate and channel
conversion is already available in generic audio-graph driver. Sample
size conversion support can be added based on the need in future.
The support is extended for following platforms:
* Jertson TX1
* Jetson Nano
* Jetson TX2
* Jetson AGX Xavier
* Jetson Xavier NX
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add a device tree node for NVDEC on Tegra186, and
device tree nodes for NVDEC and NVDEC1 on Tegra194.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add new properties to USB PHYs needed for enabling USB OTG mode.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Inspired by commit b8928c2b5d ("arm64: tegra: Consolidate audio card
names"). Based on this update HDA card name on Jetson TX2 NX platform.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Enable support for audio-graph based sound card on Jetson TX2 NX.
Following I/O interfaces are enabled.
* I2S1 and I2S3
* DMIC1 and DMIC2
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
As usual, the bulk of work in the SoC tree goes into DT files,
this time with a roughly even split between 32-bit and 64-bit
SoCs rather than the usual mostly 64-bit changes.
New SoCs:
- Microchip SAMA7 SoC family based on Cortex-A7, a new
32-bit platform based on the older SAMA5 series.
- Qualcomm Snapdragon SDM636 and SM8150, variations of the
existing phone SoCs.
- Renesas R-Car H3e-2G and M3e-2G SoCs, variations of
older Renesas SoCs.
New boards:
- Marvell CN913x reference boards
- ASpeed AST2600 BMC implementations for Facebook Cloudripper,
Elbert and Fuji server boards.
- Snapdragon 665 based Sony Xperia 10II
- Snapdragon MSM8916 based Xiaomi Redmi 2
- Snapdragon MSM8226 based Samsung Galaxy S3 Neo
- NXP i.MX based 32-bit boards:
- DHCOM based PicoITX
- DHSOM based DRC0ỉ
- SolidRun SolidSense
- SKOV i.MX6 boards.
- NXP i.MX based 64-bit boards:
- Nitrogen8 SoM and MNT Reform2
- LS1088A based Traverse Ten64
- i.MX8M based GW7902.
- NVIDIA Jetson TX2 NX Developer Kit
- 4KOpen STiH418-b2264 development board
- ux500 based Samsung phones: Gavini, Codina and Kyle
- TI AM335x based Sancloud BBE Lite
- ixp4xx dts files to replace all old board files
Other changes:
- Treewide fixes for dtc warnings
- Rockchips i/o domain support
- TI OMAP/AM3 CPSW switch driver support
- Improved device support for allwinner, aspeed, qualcomm, NXP,
nvidia, Renesas, Samsung, Amlogic, Mediatek, ixp4xx, stm32, sti,
OMAP and actions.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iD8DBQBhL13Z5t5GS2LDRf4RAljwAJ0acTxOBYP8J5zETlAQRWYcYWh5hACfZOgC
Om6K0IN5+lJuaUyF/GdmqS4=
=zXua
-----END PGP SIGNATURE-----
Merge tag 'dt-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC DT updates from Arnd Bergmann:
"As usual, the bulk of work in the SoC tree goes into DT files, this
time with a roughly even split between 32-bit and 64-bit SoCs rather
than the usual mostly 64-bit changes.
New SoCs:
- Microchip SAMA7 SoC family based on Cortex-A7, a new 32-bit
platform based on the older SAMA5 series.
- Qualcomm Snapdragon SDM636 and SM8150, variations of the existing
phone SoCs.
- Renesas R-Car H3e-2G and M3e-2G SoCs, variations of older Renesas
SoCs.
New boards:
- Marvell CN913x reference boards
- ASpeed AST2600 BMC implementations for Facebook Cloudripper, Elbert
and Fuji server boards.
- Snapdragon 665 based Sony Xperia 10II
- Snapdragon MSM8916 based Xiaomi Redmi 2
- Snapdragon MSM8226 based Samsung Galaxy S3 Neo
- NXP i.MX based 32-bit boards:
- DHCOM based PicoITX
- DHSOM based DRC0ỉ
- SolidRun SolidSense
- SKOV i.MX6 boards.
- NXP i.MX based 64-bit boards:
- Nitrogen8 SoM and MNT Reform2
- LS1088A based Traverse Ten64
- i.MX8M based GW7902.
- NVIDIA Jetson TX2 NX Developer Kit
- 4KOpen STiH418-b2264 development board
- ux500 based Samsung phones: Gavini, Codina and Kyle
- TI AM335x based Sancloud BBE Lite
- ixp4xx dts files to replace all old board files
Other changes:
- Treewide fixes for dtc warnings
- Rockchips i/o domain support
- TI OMAP/AM3 CPSW switch driver support
- Improved device support for allwinner, aspeed, qualcomm, NXP,
nvidia, Renesas, Samsung, Amlogic, Mediatek, ixp4xx, stm32, sti,
OMAP and actions"
* tag 'dt-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (412 commits)
arm/arm64: dts: Fix remaining dtc 'unit_address_format' warnings
ARM: dts: rockchip: Add SFC to RV1108
arm64: dts: marvell: armada-37xx: Extend PCIe MEM space
ARM: dts: aspeed: p10bmc: Add power control pins
ARM: dts: aspeed: cloudripper: Add comments for "mdio1"
ARM: dts: aspeed: minipack: Update flash partition table
dt-bindings: arm: fsl: Add Traverse Ten64 (LS1088A) board
dt-bindings: vendor-prefixes: add Traverse Technologies
arm64: dts: add device tree for Traverse Ten64 (LS1088A)
arm64: dts: ls1088a: add missing PMU node
arm64: dts: ls1088a: add internal PCS for DPMAC1 node
ARM: dts: imx6qp-prtwd3: configure ENET_REF clock to 125MHz
ARM: dts: vf610-zii-dev-rev-b: Remove #address-cells and #size-cells property from at93c46d dt node
ARM: dts: add SKOV imx6q and imx6dl based boards
dt-bindings: arm: fsl: add SKOV imx6q and imx6dl based boards
dt-bindings: vendor-prefixes: Add an entry for SKOV A/S
arm64: dts: imx8mq-reform2: add sound support
arm64: dts: imx8m: drop interrupt-affinity for pmu
arm64: dts: imx8qxp: update pmu compatible
arm64: dts: imx8mm: update pmu compatible
...
Contains a couple of fixes across the board and adds support for the
recently released NVIDIA Jetson TX2 NX Developer Kit.
-----BEGIN PGP SIGNATURE-----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=GoQ0
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=VTDC
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.15-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/dt
arm64: tegra: Device tree changes for v5.15-rc1
Contains a couple of fixes across the board and adds support for the
recently released NVIDIA Jetson TX2 NX Developer Kit.
* tag 'tegra-for-5.15-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: tegra: Fix compatible string for Tegra132 CPUs
arm64: tegra: Add missing interconnects property for USB on Tegra186
arm64: tegra: Add NVIDIA Jetson TX2 NX Developer Kit support
arm64: tegra: Add PWM nodes on Tegra186
arm64: tegra194: p2888: Correct interrupt trigger type of temperature sensor
arm64: tegra: Fix Tegra194 PCIe EP compatible string
Link: https://lore.kernel.org/r/20210813162157.2820913-6-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The documented compatible string for the CPUs found on Tegra132 is
"nvidia,tegra132-denver", rather than the previously used compatible
string "nvidia,denver".
Signed-off-by: Thierry Reding <treding@nvidia.com>
The device tree node for the XUDC (USB device mode controller) is
missing the interconnects property that describes the path to memory for
the controller. Add the property so that the things like the DMA mask
can be set by the operating system.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Jetson TX2 NX Developer Kit is very similar to the Jetson Nano, but
uses the more powerful Tegra186 SoC.
Signed-off-by: Thierry Reding <treding@nvidia.com>
These PWMs can be used for fan or LED backlight control. Add the device
tree nodes for all existing controllers found on Tegra186 SoCs. None of
these are enabled by default, which is left for the board DTS files to
do when necessary.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The LM90 temperature sensor should use edge-triggered interrupt because
LM90 hardware doesn't deassert interrupt line until temperature is back
to normal state, which results in interrupt storm. Correct the interrupt
trigger type.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The initialization sequence performed by the generic platform driver
pcie-designware-plat.c for a DWC based implementation doesn't work for
Tegra194. Tegra194 has a different initialization sequence requirement
which can only be satisfied by the Tegra194 specific platform driver
pcie-tegra194.c. So, remove the generic compatible string "snps,dw-pcie-ep"
from Tegra194's endpoint controller nodes.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
As of commit c7289b1c8a ("arm64: tegra: Enable SMMU support on
Tegra194"), SMMU support is enabled system-wide on Tegra194. However,
there was a bit of overlap between the SMMU enablement and the PCIe
support addition, so the PCIe device tree nodes are missing the iommus
and interconnects properties. This in turn leads to SMMU faults for
these devices, since by default the ARM SMMU will fault.
Add the iommus and interconnects properties to all the PCIe device
tree nodes to restore their functionality.
Fixes: c7289b1c8a ("arm64: tegra: Enable SMMU support on Tegra194")
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
As of commit c7289b1c8a ("arm64: tegra: Enable SMMU support on
Tegra194"), SMMU support is enabled system-wide on Tegra194. However,
there was a bit of overlap between the SMMU enablement and the USB
support addition, so the USB device tree nodes are missing the iommus
and interconnects properties. This in turn leads to SMMU faults for
these devices, since by default the ARM SMMU will fault.
Add the iommus and interconnects properties to the XUSB and XUDC device
tree nodes to restore their functionality.
Fixes: c7289b1c8a ("arm64: tegra: Enable SMMU support on Tegra194")
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add iommus and interconnects properties to the sound device tree node on
Tegra194. This ensures that the correct SID is used for translation of
physical to I/O virtual addresses and that the path to system memory is
properly described, which in turn can impact the range of memory that
the device can address.
Fixes: c7289b1c8a ("arm64: tegra: Enable SMMU support on Tegra194")
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the device tree node for the dual-SMMU found on Tegra194 and hook up
peripherals such as host1x, BPMP, HDA, SDMMC, EQOS and VIC.
Signed-off-by: Thierry Reding <treding@nvidia.com>
On Tegra186 and later, the memory controller needs to be programmed in
coordination with any of the ARM SMMU instances to configure the stream
ID used for each memory client.
To support this, add a phandle reference to the memory controller to the
SMMU device tree node.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The SMMU found on Tegra186 requires interoperation with the memory
controller in order to program stream ID overrides. The generic ARM SMMU
500 compatible is therefore inaccurate. Replace it with a more correct,
SoC-specific compatible string.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Enable support for audio-graph based sound card on Jetson Xavier NX.
Following I/O interfaces are enabled.
- I2S3 and I2S5
- DMIC1, DMIC2 and DMIC4
- DSPK1 and DSPK2
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The current scheme for audio card names is suboptimal because it causes
the automatically generated names (for ID and driver) to be truncated,
which in turn can cause conflicts.
Introduce a new scheme which reuses the board model for the names and
appends the "HDA" and "APE" suffixes for the HDA and APE, respectively.
As a side-effect these suffixes end up being used as the ID of the SoC
sound cards which makes it easy for users to select them when using the
ALSA command-line utilities, for example.
As a separate measure, the driver name for the cards is now set by the
corresponding audio driver (either tegra-hda or tegra-ape), making it a
more useful identifier than the currently normalized card name.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Populate the device-tree node for the PMU device on Tegra194. This also
fixes the following warning that is observed on booting Tegra194.
ERR KERN kvm: pmu event creation failed -2
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
An endpoint is not a device and it is recommended to use clocks property
in device node. RT5658 Codec binding already specifies the usage of
clocks property. Thus move the clocks from endpoint to device node.
Fixes: 5b4f632309 ("arm64: tegra: Audio graph sound card for Jetson AGX Xavier")
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
There are two variants of the Jetson Xavier NX platform; one has an
eMMC and one as a micro SD-card slot. The SDHCI controller used by
each variant is different, however, the current device-tree for both
Xavier NX boards have the same SDHCI controller defined as 'mmc0' in
the device-tree alias node. Fix this by correcting the 'mmc0' alias
for the SD-card variant.
Fixes: 3f9efbbe57 ("arm64: tegra: Add support for Jetson Xavier NX")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Commit 5d25c476f2 ("Revert "arm64: tegra: Disable the ACONNECT for
Jetson TX2"") re-enabled the Tegra ADMA and ACONNECT drivers to support
audio on Jetson TX2. However, this revert was dependent upon commit
e590474768 ("driver core: Set fw_devlink=on by default") and without
this commit, enabling the ACONNECT is causing resume from system suspend
to fail on Jetson TX2. Resume fails because the ACONNECT driver is being
resumed before the BPMP driver, and the ACONNECT driver is attempting to
power on a power-domain that is provided by the BPMP.
Commit e590474768 ("driver core: Set fw_devlink=on by default") has
since been temporarily reverted while some issues are being
investigated. This is causing resume from system suspend on Jetson TX2
to fail again. Rather than disable the ACONNECT driver again, fix this
by setting fw_devlink is set to 'on' for Jetson TX2 in the bootargs
specified in device-tree.
Fixes: 5d25c476f2 ("Revert arm64: tegra: Disable the ACONNECT for Jetson TX2")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The ACONNECT device tree node has a unit-address on all other SoC
generations and there's really no reason not to have it on Tegra186.
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Enable support for audio-graph based sound card on Jetson AGX Xavier.
Following I/O interfaces are enabled.
* I2S1, I2S2, I2S4 and I2S6
* DMIC3
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Enable support for audio-graph based sound card on Jetson TX2. Based
on the board design following I/O modules are enabled.
* All I2S instances (I2S1 ... I2S6)
* All DSPK instances (DSPK1, DSPK2)
* DMIC1, DMIC2 and DMIC3
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add support for the variant of the Jetson Xavier NX Developer Kit that
has a system-on-module which includes an eMMC.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
There are two versions of the Jetson Xavier NX system-on-module; one
with a micro SD-card slot and one with an eMMC. Currently, only the
system-on-module with the micro SD-card slot is supported. Before adding
support for the eMMC variant, move the common device-tree parts of the
existing Jetson Xavier NX system-on-module board (p3668-0000) and
reference carrier board (p3509-0000) into include files that can be used
by both Jetson Xavier NX variants.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Enable support for audio-graph based sound card on Jetson-Nano and
Jetson-TX1. Depending on the platform, required I/O interfaces are
enabled.
* Jetson-Nano: Enable I2S3, I2S4, DMIC1 and DMIC2.
* Jetson-TX1: Enable all I2S and DMIC interfaces.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Expose a header which describes DT bindings required to use audio-graph
based sound card. All Tegra210 based platforms can include this header
and add platform specific information. Currently, from SoC point of view,
all links are exposed for ADMAIF, AHUB, I2S and DMIC components.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Device tree nodes are ordered by unit-address and alphabetically by name
if a node doesn't have a unit-address. The thermal sensor and timer
nodes were not sorted in the correct order, so do that now.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This commit enables USB host mode at J512 type-C port of Jetson-Xavier.
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
PMC driver provides USB sleepwalk registers access to XUSB PADCTL
driver. This commit adds a "nvidia,pmc" property which points to
PMC node to XUSB PADCTL device node.
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
HDA initialization is failing occasionally on Tegra210 and following
print is observed in the boot log. Because of this probe() fails and
no sound card is registered.
[16.800802] tegra-hda 70030000.hda: no codecs found!
Codecs request a state change and enumeration by the controller. In
failure cases this does not seem to happen as STATETS register reads 0.
The problem seems to be related to the HDA codec dependency on SOR
power domain. If it is gated during HDA probe then the failure is
observed. Building Tegra HDA driver into kernel image avoids this
failure but does not completely address the dependency part. Fix this
problem by adding 'power-domains' DT property for Tegra210 HDA. Note
that Tegra186 and Tegra194 HDA do this already.
Fixes: 742af7e7a0 ("arm64: tegra: Add Tegra210 support")
Depends-on: 96d1f078ff ("arm64: tegra: Add SOR power-domain for Tegra210")
Cc: <stable@vger.kernel.org>
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
As per the HDA binding doc reorder {clock,reset}-names entries for
Tegra194. This also serves as a preparation for converting existing
binding doc to json-schema.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra AHCI dt-binding doc is converted from text based to yaml based.
dtbs_check valdiation strictly follows reset-names order specified
in yaml dt-binding.
Tegra124 thru Tegra210 has 3 resets sata, sata-oob and sata-cold.
Tegra186 has 2 resets sata and sata-cold.
This patch changes order of SATA resets to maintain proper resets
order for commonly available resets across Tegra124 thru Tegra186
for dtbs_check to pass.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This commit adds "interrupts" property to Tegra210/Tegra186/Tegra194
XUSB PADCTL node. XUSB PADCTL interrupt will be raised when USB wake
event happens. This is required for supporting XUSB host controller
ELPG.
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
DMA device nodes should follow regex pattern of "^dma-controller(@.*)?$".
This is a preparatory patch to use YAML doc format for ADMA.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
For some reason this was never hooked up. Do it now so that over-current
interrupts can be logged.
Reported-by: Nicolas Chauvet <kwizart@gmail.com>
Suggested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
According to dmesg, thermal-zones for mem and cpu are missing hot
temperatures properties.
throttrip: pll: missing hot temperature
...
throttrip: mem: missing hot temperature
...
Adding them will clear the messages.
Signed-off-by: Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
On Jetson TX1 the following message can be seen:
tegra_soctherm 700e2000.thermal-sensor: throttle-cfg: heavy: no throt prop or invalid prop
This patch will fix the invalid prop issue according to the binding.
Signed-off-by: Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
According to dmesg, thermal-zones for mem and cpu are missing hot
temperatures properties.
throttrip: pll: missing hot temperature
...
throttrip: mem: missing hot temperature
...
Adding them will clear the messages.
Signed-off-by: Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Fix the device-tree entry that represents I/O High Voltage property
by replacing 'nvidia,io-high-voltage' with 'nvidia,io-hv' as the former
entry is deprecated.
Fixes: dbb72e2c30 ("arm64: tegra: Add configuration for PCIe C5 sideband signals")
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
GIC400 has full support for virtualization, and yet the tegra186
DT doesn't expose the GICH/GICV regions (despite exposing the
maintenance interrupt that only makes sense for virtualization).
Add the missing regions, based on the hunch that the HW doesn't
use the CPU build-in interfaces, but instead the external ones
provided by the GIC. KVM's virtual GIC now works with this change.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the description of CPU PMUs for both the Denver and A57 clusters,
which enables the perf subsystem.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
When the device-tree board file was added for the Tegra234 VDK simulator
it incorrectly used the names 'cbb' and 'sdhci' instead of 'bus' and
'mmc', respectively. The names 'bus' and 'mmc' are required by the
device-tree json-schema validation tools. Therefore, fix this by
renaming these nodes accordingly.
Fixes: 639448912b ("arm64: tegra: Initial Tegra234 VDK support")
Reported-by: Ashish Singhal <ashishsingha@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The AON HSP node's "reg" property size 0xa0000 will overlap with other
resources. This patch fixes that wrong value with correct size 0x90000.
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Dipen Patel <dipenp@nvidia.com>
Fixes: a38570c22e ("arm64: tegra: Add nodes for TCU on Tegra194")
Signed-off-by: Thierry Reding <treding@nvidia.com>
USB host mode is broken on the OTG port of Jetson TX1 platform because
the USB_VBUS_EN0 regulator (regulator@11) is being overwritten by the
vdd-cam-1v2 regulator. This commit rearranges USB_VBUS_EN0 to be
regulator@14.
Fixes: 257c8047be ("arm64: tegra: jetson-tx1: Add camera supplies")
Cc: stable@vger.kernel.org
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Jetson Xavier NX board routes UARTA to the 40-pin header and UARTC
to a 12-pin debug header. The UARTs can be used by either the Tegra
Combined UART (TCU) driver or the Tegra 8250 driver. By default, the
TCU will use UARTC on Jetson Xavier NX. Currently, device-tree for
Xavier NX enables the TCU and the Tegra 8250 node for UARTC. Fix this
by disabling the Tegra 8250 node for UARTC and enabling the Tegra 8250
node for UARTA.
Fixes: 3f9efbbe57 ("arm64: tegra: Add support for Jetson Xavier NX")
Cc: stable@vger.kernel.org
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Commit ff4c371d2b ("arm64: defconfig: Build ADMA and ACONNECT driver")
enable the Tegra ADMA and ACONNECT drivers and this is causing resume
from system suspend to fail on Jetson TX2. Resume is failing because the
ACONNECT driver is being resumed before the BPMP driver, and the ACONNECT
driver is attempting to power on a power-domain that is provided by the
BPMP. While a proper fix for the resume sequencing problem is identified,
disable the ACONNECT for Jetson TX2 temporarily to avoid breaking system
suspend.
Please note that ACONNECT driver is used by the Audio Processing Engine
(APE) on Tegra, but because there is no mainline support for APE on
Jetson TX2 currently, disabling the ACONNECT does not disable any useful
feature at the moment.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The NVIDIA Tegra234 VDK is a simulation platform for the Orin SoC. It
supports a subset of the peripherals that will be available in the final
chip and serves as a bootstrapping platform.
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Populate the EEPROMs that are present on the Jetson Xavier NX developer
platform.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Populate the label property for the AT24 EEPROMs on the various Jetson
platforms. Note that the name 'module' is used to identify the EEPROM
on the processor module board and the name 'system' is used to identify
the EEPROM on the main base board (which is sometimes referred to as
the carrier board).
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This patch adds few AHUB modules for Tegra210, Tegra186 and Tegra194.
Bindings for following modules are added.
* AHUB added as a child node under ACONNECT
* AHUB includes many HW accelerators and below components are added
as its children.
* ADMAIF
* I2S
* DMIC
* DSPK (added for Tegra186 and Tegra194 only, since Tegra210 does
not have this module)
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
These devices are required for audio sub system and current patch
ensures probe path of these devices gets tested. Later sound card
support would be added which can use these devices at runtime.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
commit 5425fb15d8 ("arm64: tegra: Add Tegra194 chip device tree")
Tegra194 uses separate SDMMC_LEGACY_TM clock for data timeout and
this clock is not enabled currently which is not recommended.
Tegra194 SDMMC advertises 12Mhz as timeout clock frequency in host
capability register.
So, this clock should be kept enabled by SDMMC driver.
Fixes: 5425fb15d8 ("arm64: tegra: Add Tegra194 chip device tree")
Cc: stable <stable@vger.kernel.org> # 5.4
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Link: https://lore.kernel.org/r/1598548861-32373-7-git-send-email-skomatineni@nvidia.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
commit 39cb62cb89 ("arm64: tegra: Add Tegra186 support")
Tegra186 uses separate SDMMC_LEGACY_TM clock for data timeout and
this clock is not enabled currently which is not recommended.
Tegra186 SDMMC advertises 12Mhz as timeout clock frequency in host
capability register and uses it by default.
So, this clock should be kept enabled by the SDMMC driver.
Fixes: 39cb62cb89 ("arm64: tegra: Add Tegra186 support")
Cc: stable <stable@vger.kernel.org> # 5.4
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Link: https://lore.kernel.org/r/1598548861-32373-6-git-send-email-skomatineni@nvidia.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
commit 742af7e7a0 ("arm64: tegra: Add Tegra210 support")
Tegra210 uses separate SDMMC_LEGACY_TM clock for data timeout and
this clock is not enabled currently which is not recommended.
Tegra SDMMC advertises 12Mhz as timeout clock frequency in host
capability register.
So, this clock should be kept enabled by SDMMC driver.
Fixes: 742af7e7a0 ("arm64: tegra: Add Tegra210 support")
Cc: stable <stable@vger.kernel.org> # 5.4
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Link: https://lore.kernel.org/r/1598548861-32373-5-git-send-email-skomatineni@nvidia.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
