To reclaim TX BD, we need to read hardware reading index to determine if
any DMA is complete. Since this IO spends time, do this thing only if we
really need it when TX BD has no free buffer corresponding to target skb.
The experimental result shows that reading counter decreases from 26,000
to 130 per second.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-4-pkshih@realtek.com
RPWM/CPWM are registers that can set and check low power mode. Since chips
use different address, add a field to access them in common flow.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-3-pkshih@realtek.com
8852CE uses different but similar IMR/ISR registers, and its masks are also
different in various states, so add config_intr_mask ops to configure masks
according to under_recovery or low_power states.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-2-pkshih@realtek.com
Disable this capability to avoid timeout errors on certain platforms.
Without it, pci bus might stuck and leads to disconnection.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Tested-by: Chris Chiu <chris.chiu@canonical.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220420093058.31646-2-pkshih@realtek.com
This avoids below warning and makes compiler happy.
error: uninitialized symbol 'tim_offset'
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220420093058.31646-1-pkshih@realtek.com
During setting channel, we need to backup/restore and disable/enable some
settings. The settings include SCH (scheduler channel), PPDU status report,
and RF components, DFS and ADC.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220414062027.62638-13-pkshih@realtek.com
BB does many settings during setting channel. First is to configure CCK
for 2G channels, and then basic channel and bandwidth settings with a
encoded channel index that will report to driver when we receive packets.
Configure spur elimination to avoid spur of CSI and NBI tones in certain
frequencies. Also, it initializes BT grant to arrange path sharing with
BT according to band. Finally, reset TSSI and BB hardware to ensure it
stays in initial state.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220414062027.62638-12-pkshih@realtek.com
Add parser for bb gain table and configure bb gain table for 8852c.
While ctrl_ch, obtain bb gain error settings and write them to phy.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220414062027.62638-7-pkshih@realtek.com
chip_ops::bb_sethw is to initialize BB settings out of BB parameters
tables. Once switching channel or initialing, we do chip_ops::bb_reset to
reset hardware counters and states to make things in expectation.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220414062027.62638-6-pkshih@realtek.com
TSSI is used to manage TX power with thermal value as a factor. This patch
is to configure bandedge to TX proper waveform.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220414062027.62638-5-pkshih@realtek.com
TX power track tables are used to do TX power compensation according to
thermal value. In order to work in existing and new chip, add new 6G
entries, and change type from u8 to s8.
Internal version table is HALRF_027_00_031.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220414062027.62638-4-pkshih@realtek.com
TX power depends on rate, but must follow regulation for specific country.
Once asked to set channel, we configure registers according to these TX
power tables.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220414062027.62638-3-pkshih@realtek.com
These parameters are used to initialize BB and RF hardware when we are
going to bring up interface and start to transmit and receive.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220414062027.62638-2-pkshih@realtek.com
DCTL is short for D-MAC control that V1 chip uses this H2C to configure
security CAM. Implement the callers in next patch.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220413010804.8941-3-pkshih@realtek.com
In order to support new chip that has capability of 160M, we need new
format to fill new information, so add a new V1 ID for newer use. Since
most fields are the same, fill fields according to the function ID of chip.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220413010804.8941-2-pkshih@realtek.com
There are some spelling mistakes in the comments. Fix it.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Lv Ruyi <lv.ruyi@zte.com.cn>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220411032458.2517551-1-lv.ruyi@zte.com.cn
There are some spelling mistakes in the comments. Fix it.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Lv Ruyi <lv.ruyi@zte.com.cn>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220408095803.2495336-1-lv.ruyi@zte.com.cn
Make workaround work for other 8821CE devices with different PCI ID
Signed-off-by: Jimmy Hon <honyuenkwun@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220407075123.420696-3-honyuenkwun@gmail.com
New device ID 0xb821 found on TP-Link T2E
Tested it with c821 driver. 2.4GHz and 5GHz works.
PCI id:
05:00.0 Network controller: Realtek Semiconductor Co., Ltd. Device b821
Subsystem: Realtek Semiconductor Co., Ltd. Device b821
Signed-off-by: Jimmy Hon <honyuenkwun@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220407075123.420696-2-honyuenkwun@gmail.com
RSSI value per frame is reported to mac80211 but not maintained in
our own statistics, add it back to help us debug.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220407095858.46807-7-pkshih@realtek.com
Calling calibration to yield expected PHY performance. We do this in STA
mode, so do this in AP mode as well.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220407095858.46807-6-pkshih@realtek.com
Without this setting, hardware would not report to driver even if
management frames are transmitted successfully. So we fix it.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220407095858.46807-5-pkshih@realtek.com
To support stations in power saving mode, AP should notify stations
that there are frames buffered at the AP via TIM during beacons.
Driver used to transmit identical beacons that were downloaded to
hardware during the initiation phase. This beacon will become
obsolete over time.
If the beacon does not contain sufficient information, station would
not be able to percept that there is data to receive. Hence it won't
wake up and start the PS-poll procedure, this could lead to timeout
and/or lost data segments. In order to resolve this issue, driver will
now download beacon to hardware whenever the content is updated.
Enable hardware to update dtim_count for more efficiency, this reduces
the overhead of downloading beacon at every beacon interval since most
of the time only the dtim_count needs to be updated.
Change queue mapping for broadcast/multicast frames to high queue, so
these frames can be prioritized and sent when dtim_count is zero.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220407095858.46807-4-pkshih@realtek.com
We should only fill in frequency reported by firmware during scan.
Add this so frames won't be dropped by mac80211 due to frequency
mismatch.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220407095858.46807-3-pkshih@realtek.com
Adding this allows us to get notification when bitrate configuration
of the station changes. Update according parameters to firmware so
the rate control algorithm can work properly.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220407095858.46807-2-pkshih@realtek.com
Change the struct and the uses to const to reduce data.
$ size drivers/net/wireless/realtek/rtw89/ser.o* (x86-64 defconfig w/ rtw89)
text data bss dec hex filename
3741 8 0 3749 ea5 drivers/net/wireless/realtek/rtw89/ser.o.new
3437 312 0 3749 ea5 drivers/net/wireless/realtek/rtw89/ser.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/2fd88e6119f62b968477ef9781abb1832d399fd6.camel@perches.com
Initialize registers to default values, such as PTA and GNT pin, and set
pin MUX according to number of antenna on hardware module.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220408001353.17188-10-pkshih@realtek.com
Separated DIG RX gain, IGI configurations from not supportted HW using
"support_igi" capability flag.
Signed-off-by: Johnson Lin <johnson.lin@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220408001353.17188-9-pkshih@realtek.com
Disable watchdog timer to prevent it timeout suddenly.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220408001353.17188-8-pkshih@realtek.com
The bit B_AX_SS_NONEMPTY_SS2FINFO_EN should be clear, because we configure
C-MAC as hardware TX/RX mode.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220408001353.17188-6-pkshih@realtek.com
Turn on ERR IMR, and then firmware can capture interrupts reflecting
errors to recover hardware states.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220408001353.17188-5-pkshih@realtek.com
Similarly, create functions to set specific C-MAC masks for firmware
recovery.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220408001353.17188-4-pkshih@realtek.com
These interrupts are used by firmware to recover hardware. Create
functions to set specific D-MAC masks to replace plain register settings.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220408001353.17188-3-pkshih@realtek.com
add `break` to fix warning of unannotated fall-through between switch
labels.
Fixes: 14f9f47900 ("rtw89: ser: control hci interrupts on/off by state")
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220408001353.17188-2-pkshih@realtek.com
Currently in mac80211 each STA object is represented
using sta_info datastructure with the associated
STA specific information and drivers access ieee80211_sta
part of it.
With MLO (Multi Link Operation) support being added
in 802.11be standard, though the association is logically
with a single Multi Link capable STA, at the physical level
communication can happen via different advertised
links (uniquely identified by Channel, operating class,
BSSID) and hence the need to handle multiple link
STA parameters within a composite sta_info object
called the MLD STA. The different link STA part of
MLD STA are identified using the link address which can
be same or different as the MLD STA address and unique
link id based on the link vif.
To support extension of such a model, the sta_info
datastructure is modified to hold multiple link STA
objects with link specific params currently within
sta_info moved to this new structure. Similarly this is
done for ieee80211_sta as well which will be accessed
within mac80211 as well as by drivers, hence trivial
driver changes are expected to support this.
For current non MLO supported drivers, only one link STA
is present and link information is accessed via 'deflink'
member.
For MLO drivers, we still need to define the APIs etc. to
get the correct link ID and access the correct part of
the station info.
Currently in mac80211, all link STA info are accessed directly
via deflink. These will be updated to access via link pointers
indexed by link id with MLO support patches, with link id
being 0 for non MLO supported cases.
Except for couple of macro related changes, below spatch takes
care of updating mac80211 and driver code to access to the
link STA info via deflink.
@ieee80211_sta@
struct ieee80211_sta *s;
struct sta_info *si;
identifier var = {supp_rates, ht_cap, vht_cap, he_cap, he_6ghz_capa, eht_cap, rx_nss, bandwidth, txpwr};
@@
(
s->
- var
+ deflink.var
|
si->sta.
- var
+ deflink.var
)
@sta_info@
struct sta_info *si;
identifier var = {gtk, pcpu_rx_stats, rx_stats, rx_stats_avg, status_stats, tx_stats, cur_max_bandwidth};
@@
(
si->
- var
+ deflink.var
)
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Link: https://lore.kernel.org/r/1649086883-13246-1-git-send-email-quic_srirrama@quicinc.com
[remove MLO-drivers notes from commit message, not clear yet; run spatch]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
RTL8188CUS/RTL8192CU(gen1) don't support rate adaptive report hence
no real txrate info can be retrieved. The vendor driver reports the
highest rate in HT capabilities from the IEs to avoid empty txrate.
This commit initiates the txrate information with the highest supported
rate negotiated with AP. The gen2 chip keeps update the txrate from
the rate adaptive reports, and gen1 chips at least have non-NULL txrate
after associated.
Signed-off-by: Chris Chiu <chris.chiu@canonical.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220325035735.4745-3-chris.chiu@canonical.com
Fill up the available TX/RX antenna so the iw commands can show
correct antenna information for different chips.
Signed-off-by: Chris Chiu <chris.chiu@canonical.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220325035735.4745-2-chris.chiu@canonical.com
To move the list iterator variable into the list_for_each_entry_*()
macro in the future it should be avoided to use the list iterator
variable after the loop body.
To *never* use the list iterator variable after the loop it was
concluded to use a separate iterator variable instead of a
found boolean [1].
This removes the need to use a found variable and simply checking if
the variable was set, can determine if the break/goto was hit.
Link: https://lore.kernel.org/all/CAHk-=wgRr_D8CB-D9Kg-c=EHreAsk5SqXPwr9Y7k9sA6cWXJ6w@mail.gmail.com/
Signed-off-by: Jakob Koschel <jakobkoschel@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220324072124.62458-1-jakobkoschel@gmail.com
Without this patch, hw scan won't stay long enough on DFS/passive
channels. Found previous logic error and fix it.
Signed-off-by: Po Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220401055043.12512-5-pkshih@realtek.com
Turn off coexistence driver control, let firmware can control the
traffic during scan. This prevents potential unexpected behavior of
the BT driver.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220401055043.12512-4-pkshih@realtek.com
Add a dummy function for packet offload to eliminate warning message
"c2h class 1 func 2 not support". This c2h is for debug purpose and
its presence itself can do the work, so further parsing won't be
required for now.
Signed-off-by: Po Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220401055043.12512-3-pkshih@realtek.com
Previously we only consider single interface's status, idle mode
behavior could be unexpected when multiple interfaces is active.
Change to enter/leave idle mode by mac80211's configuration state.
Signed-off-by: Po Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220401055043.12512-2-pkshih@realtek.com
Address info registers are used to configure size of DMA address info to
point skb->data. With different size, it can support different number of
scatters.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220325060055.58482-6-pkshih@realtek.com
The pre_init is used to initialize partial PCI function during PCI probe.
It doesn't need to initialize all functions, so probe can be faster.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220325060055.58482-4-pkshih@realtek.com
The PCI code of 8852AE and 8852CE are different, but the flow and register
names are similar. To reuse the code, add a struct to define register or
value accordingly. We also use chip id to control the slightly different
flow.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220325060055.58482-2-pkshih@realtek.com
The smatch reports:
rtw8852a.c:1857 rtw8852a_btc_set_wl_txpwr_ctrl() error: uninitialized symbol '_cur'.
rtw8852a.c:1858 rtw8852a_btc_set_wl_txpwr_ctrl() error: uninitialized symbol '_cur'.
This is because rtw89_mac_txpwr_read32() can possibly return before setting
argument _cur, and the caller will use the uninitialized value. To fix this
problem, check the return value of rtw89_mac_txpwr_read32().
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220318035202.42437-1-pkshih@realtek.com
8852C uses different fields to represent RX bandwidth. Since other fields
are the same, I check chip_id to get bandwidth instead of creating another
v1 function.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220318023214.32411-12-pkshih@realtek.com
The newer chip will generate security header itself, so don't set
IEEE80211_KEY_FLAG_GENERATE_IV in this kind of chip. But, it needs to fill
key_index, PN and 802.11 header length to TX descriptor, and then hardware
uses these to generate security header.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220318023214.32411-11-pkshih@realtek.com
The txdesc is descriptor related to skb->data. The v1 version contains
8 dwords txwd_body and 6 dwords txwd_info, and the format is also different
from original one.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220318023214.32411-10-pkshih@realtek.com
The txaddr_info is used to fill the DMA address of skb->data. The v1
version can support up to 10 entries, but the maximum size of each entry
is 2047, so it fill more than one entry for large packet, like 3000 bytes.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220318023214.32411-9-pkshih@realtek.com
8852A and 8852C use different H2C header and size, so add h2c_desc_size
to allocate different header size and fill content by fill_txdesc_fwcmd.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220318023214.32411-8-pkshih@realtek.com
Bypass IGI, known as Rx gain, adjustment flow for incompatible hardware
architectures.
Signed-off-by: Johnson Lin <johnson.lin@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220318023214.32411-7-pkshih@realtek.com
Refinement of DIG flow, a mechanism to adjust Rx gain for better Rx
performance, by packing IGI(initial gain index) configuration flow into
one function.
Signed-off-by: Johnson Lin <johnson.lin@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220318023214.32411-6-pkshih@realtek.com
Update notes:
Configure rtw89_regulatory for 6G band according to country.
Adjust country GB to use RTW89_UK entry on all bands.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220318023214.32411-5-pkshih@realtek.com
Wrap regd debug dump into a macro and add dump for 6G band field.
Extend the macro used to configure regd table to account for multiple
bands beyond 2G and 5G.
And the follow-up commit will configure the corresponding values for
6G band into regd table.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220318023214.32411-4-pkshih@realtek.com
Update notes:
TX power by rate table is not changed.
TX power limit table configures values for UK.
TX power limit RU table configures values for UK.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220318023214.32411-3-pkshih@realtek.com
Add RTW89_UK to enum rtw89_regulation_type.
The follow-up commit will configure the corresponding values for it
to TX power tables.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220318023214.32411-2-pkshih@realtek.com
An export symbol costs about 40 bytes (in x86 with gcc), so use a structure
containing these small arrays to reduce code size.
text data bss dec hex filename
34932 1410 0 36342 8df6 mac.o (before)
34276 1258 0 35534 8ace mac.o (after)
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220315015522.11366-1-pkshih@realtek.com
Originally, there is already a mechanism, SER (system error recover),
to deal with HW/FW recovery. After FW v0.13.36.0, FW supports a H2C
(host to chip) command to make a CPU exception. Then, SER is supposed
to catch this FW crash and do L2 reset. This feature is a simulation
to verify if flow of recovering from FW crash works.
Usage of fw_crash debugfs is as the following.
$ echo 1 > fw_crash // trigger FW crash and wait SER handling
$ cat fw_crash // return 0 if restart has been done
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220314071250.40292-9-pkshih@realtek.com
As the fw features gradually increase, it would be better that
we have a set of methods to maintain fw features instead of using
scattered bool variables.
We reconstruct the way fw recognize features, and introduce
RTW89_CHK_FW_FEATURE() / RTW89_SET_FW_FEATURE() to check / set
fw features for uses.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220314071250.40292-8-pkshih@realtek.com
Read FW backtrace entry through FW reserved payload engine, and then
add FW backtrace dump during SER (system error recover) L2 reset process.
It contains a list of RA (return address) and SP (stack pointer) which
gives us a chance to trace back the call stack of FW.
Moreover, if core dump might have wrong content due to error during
dumping, we won't invoke device core dump framework. For this case,
rtw89_ser_cd_free() is added to free buffer by ourselves.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220314071250.40292-7-pkshih@realtek.com
When FW encounters exception or assertion, SER L2 reset process will start.
It will dump some error information and re-download FW eventually. Since
such errors are usually critical, we would like to keep more information
about error to increase possibility of analysis and debugging FW. We first
add FW payload engine (fw reserved playoad engine, fw_rsvd_ple) memory
dump. FW will record things like CPU registers, backtrace entry, etc. in it
for debugging.
Moreover, device core dump framework is used and wrapped to collect kinds
of dumps during SER L2 reset process.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220314071250.40292-6-pkshih@realtek.com
While SER (system error recover) is processing, it's supposed to mean
something is under recovery. So, disable interrupts (excluding the one
of halt which could be used during SER) to avoid unexpected behavior.
And then, enable interrupts after SER is done.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220314071250.40292-5-pkshih@realtek.com
The raw error code might combine error scenario and error status.
But, the error scenario isn't parsed previously. It makes us mishandle
cpu exception and assertion. Now, we correct the error status for them.
Besides, a few uses of error status are refined.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220314071250.40292-4-pkshih@realtek.com
Previously, mac_mem_base_addr_table was declared in debug.c locally
because it's only used via debugfs to dump mac memory. Now, we plan to
refine SER (system error recover) flow which will also need to dump mac
memory to somewhere as information for error which is catched. So, we
move mac_mem_base_addr_table to mac.c rtw89_mac_mem_base_addrs earlier
as common code.
(no logic is changed)
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220314071250.40292-3-pkshih@realtek.com
The CAM, meaning address CAM and bssid CAM here, will get leaks during
SER (system error recover) L2 reset process and ieee80211_restart_hw()
which is called by L2 reset process eventually.
The normal flow would be like
-> add interface (acquire 1)
-> enter ips (release 1)
-> leave ips (acquire 1)
-> connection (occupy 1) <(A) 1 leak after L2 reset if non-sec connection>
The ieee80211_restart_hw() flow (under connection)
-> ieee80211 reconfig
-> add interface (acquire 1)
-> leave ips (acquire 1)
-> connection (occupy (A) + 2) <(B) 1 more leak>
Originally, CAM is released before HW restart only if connection is under
security. Now, release CAM whatever connection it is to fix leak in (A).
OTOH, check if CAM is already valid to avoid acquiring multiple times to
fix (B).
Besides, if AP mode, release address CAM of all stations before HW restart.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220314071250.40292-2-pkshih@realtek.com
Previously we only consider single interface's status, idle mode
behavior could be unexpected when multiple interfaces is active.
Change to enter/leave idle mode by mac80211's configuration state.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220318034316.40720-1-pkshih@realtek.com
These function is used to stop transmitting when we are going to switch
channels or do some RF calibration. Before these operations, we need to
stop channel transmission and backup setting into parameter tx_en. After
operations are done, resume transmitting by backup parameter tx_en.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220317055543.40514-13-pkshih@realtek.com
In order to support 8852C that uses 32 bits to control TX types.
This patch doesn't really use 32 bits tx_en yet, but next patch will
use it.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220317055543.40514-12-pkshih@realtek.com
Use if() style would be clear than "? :", because the else cases are
always 0. The read val from rtw89_mac_read_lte() isn't used, so remove
this statement.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220317055543.40514-11-pkshih@realtek.com
The BT-coexistence uses these function to control antenna and TDMA, so
implement the variant type to support all chips.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220317055543.40514-10-pkshih@realtek.com
Initialize FW status and disabled H2C function if CPU disabled. Then, it
can reset to initial state.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220317055543.40514-9-pkshih@realtek.com
8852C add new hardware feature -- preload window, which is used to load
more data to D-MAC, so it can possibly yield better performance.
This patch is to configure preload and reserved size for next window.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220317055543.40514-8-pkshih@realtek.com
Modify functions that control D-MAC (data MAC) and LDO to support variant
chips.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220317055543.40514-7-pkshih@realtek.com
The format of RF parameter is changed; it doesn't encode delay parameters
into table, but the delay coding becomes regular pair of register address
and value.
To help firmware to recover RF register settings, we need to download
these parameters to firmware. For v1 format, only download partial
parameters (ignore them with addr < 0x100).
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220317055543.40514-6-pkshih@realtek.com
Using encoded address which BIT(16) is used to discriminate which region is
going to access. Illustrate the calling flow as below
rtw89_phy_write_rf_v1() -+-> rtw89_phy_write_rf() // old interface
+-> rtw89_phy_write_rf_a() // new interface
Signed-off-by: Chung-Hsuan Hung <hsuan8331@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220317055543.40514-5-pkshih@realtek.com
Configure this TX power to indicate TX power offset that uses to transmit
TB (trigger base) uplink frames.
Also, shrink the unit of TX power offset changes to suitable type s8.
Signed-off-by: Yuan-Han Zhang <yuanhan1020@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220317055543.40514-4-pkshih@realtek.com
The CFO tracking algorithm is the same, but control methods are different.
Set parameters via xtal serial interfaces (SI).
Signed-off-by: Yuan-Han Zhang <yuanhan1020@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220317055543.40514-3-pkshih@realtek.com
The dcfo_comp is digital CFO (central frequency offset) compensation.
Since the flow can be shared with all chips, add chip parameters to support
variant register address and format.
Signed-off-by: Yuan-Han Zhang <yuanhan1020@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220317055543.40514-2-pkshih@realtek.com
There are some spelling mistakes in some literal strings. Fix them.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220316234242.55515-1-colin.i.king@gmail.com
