Due to many carrier boards pulling the usdhc1 signals up to 3.3 volt we
need to disable 1.8 volt signaling. Adding the no-1-8-v property
basically disables UHS-I modes by default.
Also pull-up the command and data lines to the +V3.3_1.8_SD rail and
set them to the 200 MHz speed grade (e.g. pinmux bits 7-6: meaning 11
SPEED_3_max_200MHz).
Explicitly specify a bus-width of <4> in the module-level device tree
include file and drop the no-1-8-v property from the carrier boards
device trees.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Move all Atmel nodes from the board-level into the main module-level
device tree and prepare the device trees for use with Atmel MXT device
tree overlays. Also, add required pinmux groups.
The common scheme for pin groups in touch screen overlays is as follows:
- pinctrl_atmel_conn - SODIMM 106/107 pins for INT/RST signals (default)
- pinctrl_atmel_adap - SODIMM 28/30 pins for INT/RST signals.
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds the proper phy-supply to the FEC. This supply is actually
switched by a clock that is now properly stated. This has the advantage
to add a delay for that particular regulator which is needed.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Switch on 22 kOhm pull-ups and lower the I2C frequency to around 40 kHz
to get more reliable communication.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Disable the keeper and enable a 100k pull-down on the ADC pins as per
the following note in section 13.2 of the i.MX 6ULL Application
Processor Reference Manual, Rev. 1, 11/2017 [1]:
The keeper causes an undesired jump behavior in ADC. To avoid the
problem, disable keeper before starting ADC.
[1] https://www.nxp.com/webapp/Download?colCode=IMX6ULLRM
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
- I2C, sound, USB, CANFD, timer, watchdog, (Q)SPI, cpufreq, and
thermal support for the RZ/G2UL SoC and the RZ/G2UL SMARC EVK
development board,
- Initial support for the R-Car V4H SoC and the Renesas White Hawk
development board stack,
- DMA, RTC, and USB support for the RZ/N1D SoC,
- Initial support for the RZ/V2M SoC an the RZ/V2M Evaluation Kit
Board,
- Miscellaneous fixes and improvements.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCYnTmCAAKCRCKwlD9ZEnx
cNXAAP4zWJnWNezZM//dRYwLHALSOE5x22y+MJyiDYDPO2Z0FgD+LcVO1AV+FEqN
/vFkQRBThrdcARFqc44lSYGj2f2+kgg=
=L6Mz
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=3n4A
-----END PGP SIGNATURE-----
Merge tag 'renesas-arm-dt-for-v5.19-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/dt
Renesas ARM DT updates for v5.19 (take two)
- I2C, sound, USB, CANFD, timer, watchdog, (Q)SPI, cpufreq, and
thermal support for the RZ/G2UL SoC and the RZ/G2UL SMARC EVK
development board,
- Initial support for the R-Car V4H SoC and the Renesas White Hawk
development board stack,
- DMA, RTC, and USB support for the RZ/N1D SoC,
- Initial support for the RZ/V2M SoC an the RZ/V2M Evaluation Kit
Board,
- Miscellaneous fixes and improvements.
* tag 'renesas-arm-dt-for-v5.19-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel: (40 commits)
arm64: dts: renesas: Add initial device tree for RZ/V2M EVK
arm64: dts: renesas: Add initial DTSI for RZ/V2M SoC
arm64: dts: renesas: r8a779a0: Update to R-Car Gen4 compatible values
ARM: dts: r9a06g032: Link the PCI USB devices to the USB PHY
ARM: dts: r9a06g032: Add USB PHY DT support
ARM: dts: r9a06g032: Add internal PCI bridge node
ARM: dts: r9a06g032: Describe the RTC
arm64: dts: renesas: Add interrupt-names to CANFD nodes
arm64: dts: renesas: r9a07g043: Add SPI Multi I/O Bus controller node
arm64: dts: renesas: r9a07g043: Create thermal zone to support IPA
arm64: dts: renesas: r9a07g043: Add TSU node
arm64: dts: renesas: r9a07g043: Add OPP table
arm64: dts: renesas: r9a07g043: Add RSPI{0,1,2} nodes
arm64: dts: renesas: r9a07g054: Fix external clk node names
arm64: dts: renesas: r9a07g044: Fix external clk node names
ARM: dts: r9a06g032: Fix the NAND controller node
ARM: dts: r9a06g032: Fill the UART DMA properties
ARM: dts: r9a06g032: Describe the DMA router
ARM: dts: r9a06g032: Add the two DMA nodes
arm64: dts: renesas: Remove empty rgb output endpoints
...
Link: https://lore.kernel.org/r/cover.1651828603.git.geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Align SPI NOR node names to DT schema and drop unused/undocumented
dma-channels/dma-requests.
-----BEGIN PGP SIGNATURE-----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=YfQK
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEo6/YBQwIrVS28WGKmmx57+YAGNkFAmJ1g88ACgkQmmx57+YA
GNn6RA//ffQOuX5ITQe8m4ROMAG2Sh1aX805cb036vNbmTQI3DWYWWZmunb0F56w
nUu7wFY258Aej2Z9PHmHKp5eW78zCGsdqDyZ/E+yji8LVoP3XnhOwTyKLbpd++/g
3odC/5bMBOGg9SvgM7wX+ofM4+hjPLGVH0XXVPY0KzcwgKBliNdY3e19lx08WvQg
M366Vqe7qwWKzMj9nnea5DIdpalGpwhVZSMuSANgNhIWo5JuQX8bODtP5GjMl4PZ
sn1+v7HIznGNT3WLSIYqJCtouB+069fPs6nOupYIOr0Qa/wpjrMvuTw7KXhf+eRr
94LUENOgMsTCHGHDMKxCPwZOlKYVkGi0FjGjumD0EBcsN/srqk58H0XyoT9bw4dg
523rF+RmEzSmg1QgramLnSQ732zHcYX6N5cbkpYyhXw/fwOt3eNuDCzwvvErdeSQ
fWmEbLf+oAO/75rsB5ofAJ4lwQuwc02nw02Tze2vBHUuEDeqHWNH0ZdXCiV9rlS1
J1CdAmhB/8UOkMmxyItfGzpAFU1vDp+cYG0ZQntVT0usuHm46dhGi8OFU3Q0ITdH
0kZycQDL8uczd691FIE9RuRHjQU4ECYj+kpw50wfreZ/T99hCVZ2dPsPTvd3I4cu
krb4K5wJH5AlnnLt5DLmCAwjCnUIF54zy4lEwOBEKfPBFmxXSes=
=n79H
-----END PGP SIGNATURE-----
Merge tag 'dt-cleanup-5.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/dt
Minor cleanup of ARM DTS for v5.19, part two
Align SPI NOR node names to DT schema and drop unused/undocumented
dma-channels/dma-requests.
* tag 'dt-cleanup-5.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: socfpga: drop useless 'dma-channels/requests' properties
ARM: dts: zynq-7000: drop useless 'dma-channels/requests' properties
ARM: dts: marvell: align SPI NOR node name with dtschema
ARM: dts: omap: align SPI NOR node name with dtschema
ARM: dts: nuvoton: align SPI NOR node name with dtschema
Link: https://lore.kernel.org/r/20220506081438.149192-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add device tree for the Bosch ACC board, based on i.MX6 Dual.
Signed-off-by: Philip Oberfichtner <pro@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The NXP i.MXRT1050 Evaluation Kit (EVK) provides a platform for rapid
evaluation of the i.MXRT, which features NXP's implementation of the Arm
Cortex-M7 core.
The EVK provides 32 MB SDRAM, 64 MB Quad SPI flash, Micro SD card socket,
USB 2.0 OTG.
This patch aims to support the preliminary booting up features
as follows:
GPIO
LPUART
SD/MMC
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
[Jesse: Add clock-parents, edma, usdhc, anatop, remove old pinctl]
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Describe the PCI USB devices that are behind the PCI bridge, adding
necessary links to the USB PHY device.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Link: https://lore.kernel.org/r/20220429134143.628428-8-herve.codina@bootlin.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
UART 0 to 2 do not have DMA support, while UART 3 to 7 do.
Fill the "dmas" and "dma-names" properties for each of these nodes.
Please mind that these nodes go through the dmamux node which will
redirect the requests to the right DMA controller. The first 4 cells of
the "dmas" properties will be transferred as-is to the DMA
controllers. The last 2 cells are consumed by the dmamux. Which means
cell 0 and 4 are almost redundant, one giving the controller request ID
and the other the dmamux channel which is a 1:1 translation of the
request IDs, shifted by 16 when pointing to the second DMA controller.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20220421095323.101811-11-miquel.raynal@bootlin.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
There is a dmamux on this SoC which allows picking two different sources
for a single DMA request.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20220427095653.91804-10-miquel.raynal@bootlin.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Describe the two DMA controllers available on this SoC.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20220427095653.91804-9-miquel.raynal@bootlin.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Devicetree updates for few boards and more clean-up for make dtbs warnings:
- Updates for am335x-myirtech oscillator and mtd
- Firmware configuration for i2c voltage scaling and IO isolation for am3/4
that are wired for these features
- A series of omap3 clock node clean-up for make dtbs warnings for
unique_unit_address and node_name_chars_strict
- Updates for dma-channel usage to add the generic dma-common properties
-----BEGIN PGP SIGNATURE-----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=Vx4R
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEo6/YBQwIrVS28WGKmmx57+YAGNkFAmJ0GhsACgkQmmx57+YA
GNlBxxAAnifnJBgUXC6TH4zIkiRGt2leStQ6EBo4pKKnQCMdmKr638QWDFbpFX4y
qHYbKPozfmZS9rJQ7Ngf1tYyeSs2H6Ddj9UntJpM79qXDczLehzHFQKgaXTtEcZv
zoj/TPSEoepqEgWlh1blWknReJvomVv02cWomLeueX4e+Pj5iFzLuWkokzJzpbpl
s363RvcllIBenzvfCCgMTOilYC5IRXuc5jkIC0vx1HAAn4LlPaflsZarwKSdpTsu
ZQIckcz3z6eR/AoDunPD+pR30AEKvz17AW9zpnftQoIxBQlIOCQx7MgbFqb4BDZz
4DsKGT1kZdSNxXq3ejyyYFFYoLVbIo/7mFOuX8kf2Lze1XbRCNW5RhVb1lBxpXvg
PLQC4tjhxh3cNgs8CyHlT0B3KBSBSGGfpjoHlb6vkBnSunm21YRIZBCOI0jW7+mb
NLbleV2GQ+yZ4c2wXBH4UDkhUMhb99JzAVbYRJ+iEhyAAoMKzHjRKM1EEMz5dfSS
c4Nl83sx6HsvIGz71Nl3fxMr2qpmQOnc9wEFnBQC3zlEVg8aJRBYrS5ofGg3LJZR
PPRTx1QTtUnwBf21HCnD9ksvpcLSrp6VVoPB5savWD5SwXsL01XaG9GE66UwVHVD
6iXUoKgf00AMTBj45vpdHamuGQil2COnZ+CrN6KJ1CI7oXW6QFk=
=6jOE
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.19/dt-part2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dt
More devicetree changes for omaps
Devicetree updates for few boards and more clean-up for make dtbs warnings:
- Updates for am335x-myirtech oscillator and mtd
- Firmware configuration for i2c voltage scaling and IO isolation for am3/4
that are wired for these features
- A series of omap3 clock node clean-up for make dtbs warnings for
unique_unit_address and node_name_chars_strict
- Updates for dma-channel usage to add the generic dma-common properties
* tag 'omap-for-v5.19/dt-part2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (26 commits)
ARM: dts: dm81xx: use new 'dma-channels/requests' properties
ARM: dts: am33xx: use new 'dma-channels/requests' properties
ARM: dts: Group omap3 CM_CLKSEL1_EMU clocks
ARM: dts: Group omap3 CM_CLKSEL_PER clocks
ARM: dts: Group omap3 CM_ICLKEN_PER clocks
ARM: dts: Group omap3 CM_FCLKEN_PER clocks
ARM: dts: Group omap3 CM_FCLKEN_CAM clocks
ARM: dts: Group omap3 CM_CLKSEL_DSS clocks
ARM: dts: Group omap3 CM_FCLKEN_DSS clocks
ARM: dts: Group omap3 CM_CLKOUT_CTRL clocks
ARM: dts: Group omap3 CM_CLKSEL1_PLL clocks
ARM: dts: Group omap3 CM_CLKSEL_WKUP clocks
ARM: dts: Group omap3 CM_ICLKEN_WKUP clocks
ARM: dts: Group omap3 CM_FCLKEN_WKUP clocks
ARM: dts: Group omap3 CM_CLKSEL_CORE clocks
ARM: dts: Group omap3 CM_ICLKEN3_CORE clocks
ARM: dts: Group omap3 CM_ICLKEN1_CORE clocks
ARM: dts: Group omap3 crypto accelerator clocks
ARM: dts: Group omap3 CM_FCLKEN1_CORE clocks
ARM: dts: Group omap3 CONTROL_DEVCONF1 clocks
...
Link: https://lore.kernel.org/r/pull-1651726643-535261@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
for 5.19, please pull the following:
- Oleksij fixes the ethernet node name for the USB Ethernet adapter on
BCM283x (Raspberry Pi 1/2/3) platforms
- Kuldeep fixes the PL022 SPI controller clock names to conform to the
binding
- Rafal updates the various BCM5301X (Northstar) Device Tree include
files to be dtsschema conforming for pinctrl, NAND
- Arinc adds the Asus RT-AC88U binding, removes some unnecessary
properties of the Ethernet switch DT node, populates the correct PHY
interface for port 5 of the switch, adds support for fetching the MAC
address from the NVMEM provider and finally disables gmac0 on that
device which is unused
- Phil updates the Raspberry Pi 1/2/3 DTS files to have the latest gpio
line names conforming to the printed circuit board layout
- Krzysztof updates various Broadcom DTS files to have a conforming SPI
nor Device Tree node
- Takayoshi adds support for the Buffalo WZR-1166DHP/WZR-1166DHP2
wireless routers based on the BCM4708 SoC
- William adds support for the BCM47622 ARMv7 Broadband SoC and provides
a basic DTS to boot upstream Linux on such a system
-----BEGIN PGP SIGNATURE-----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=x8WK
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=mbjq
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.19/devicetree' of https://github.com/Broadcom/stblinux into arm/dt
This pull request contains Broadcom ARM-based SoCs Device Tree changes
for 5.19, please pull the following:
- Oleksij fixes the ethernet node name for the USB Ethernet adapter on
BCM283x (Raspberry Pi 1/2/3) platforms
- Kuldeep fixes the PL022 SPI controller clock names to conform to the
binding
- Rafal updates the various BCM5301X (Northstar) Device Tree include
files to be dtsschema conforming for pinctrl, NAND
- Arinc adds the Asus RT-AC88U binding, removes some unnecessary
properties of the Ethernet switch DT node, populates the correct PHY
interface for port 5 of the switch, adds support for fetching the MAC
address from the NVMEM provider and finally disables gmac0 on that
device which is unused
- Phil updates the Raspberry Pi 1/2/3 DTS files to have the latest gpio
line names conforming to the printed circuit board layout
- Krzysztof updates various Broadcom DTS files to have a conforming SPI
nor Device Tree node
- Takayoshi adds support for the Buffalo WZR-1166DHP/WZR-1166DHP2
wireless routers based on the BCM4708 SoC
- William adds support for the BCM47622 ARMv7 Broadband SoC and provides
a basic DTS to boot upstream Linux on such a system
* tag 'arm-soc/for-5.19/devicetree' of https://github.com/Broadcom/stblinux: (22 commits)
ARM: dts: BCM5301X: Add DT for WZR-1166DHP,DHP2
ARM: dts: add dts files for bcmbca soc 47622
dt-bindings: arm: add bcmbca device tree binding document
ARM: dts: bcm283x: Align ETH_CLK GPIO line name
ARM: dts: bcm283x: Remove gpio line name NC
ARM: dts: bcm2835-rpi-b: Fix GPIO line names
ARM: dts: bcm2837-rpi-3-b-plus: Fix GPIO line name of power LED
ARM: dts: bcm2837-rpi-cm3-io3: Fix GPIO line names for SMPS I2C
ARM: dts: bcm2835-rpi-zero-w: Fix GPIO line name for Wifi/BT
ARM: dts: BCM5301X: Disable gmac0 and enable port@8 on Asus RT-AC88U
ARM: dts: broadcom: align SPI NOR node name with dtschema
dt-bindings: arm: bcm: add bindings for Asus RT-AC88U
ARM: dts: BCM5301X: Fix compatible strings for BCM53012 and BCM53016 SoC
dt-bindings: arm: bcm: create new description for BCM53016
dt-bindings: arm: bcm: fix BCM53012 and BCM53016 SoC strings
ARM: dts: BCM5301X: Retrieve gmac1 MAC address from NVRAM on Asus RT-AC88U
ARM: dts: BCM5301X: Add rgmii to port@5 of Broadcom switch on Asus RT-AC88U
ARM: dts: BCM5301X: Remove cell properties from srab ports on Asus RT-AC88U
ARM: dts: BCM5301X: Fix DTC warning for NAND node
ARM: dts: BCM5301X: Update pin controller node name
...
Link: https://lore.kernel.org/r/20220504210942.1838248-2-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Highlights:
----------
-MCU:
-Fix pinctrl node names to match with pinctrl yaml.
- MPU:
-General:
- Fix pinctrl node names to match with pinctrl yaml.
- Add Protonics boards support based on STM32MP151A SoC:
- PRTT1C - 10BaseT1L switch: mainly embeds a sja1105q switch with
TI and Micrel 10BaseT Phys and wifi support.
- PRTT1S - 10BaseT1L CO2 sensor board: mainly embeds I2C humidity
and CO2 sensors.
- PRTT1A - 10BaseT1L multi functional controller.
- ST boards:
- Add RTC support on stm32mp13.
- Add button and heartbit support on stm32mp13 DK board.
- Add a secure version of STM32MP15 ED1/EV1/DK1/DK2 boards based
on OP-TEE OS and SCMI protocol.
- DH boards:
- Use MCO2 to generate PHY clock and ETHRX clock in order to release
internal PLL for a better SD card usage.
- Add 1ms PHY post-reset on Avenger96 board to match with PHY
requirements.
-----BEGIN PGP SIGNATURE-----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=F34o
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=gddr
-----END PGP SIGNATURE-----
Merge tag 'stm32-dt-for-v5.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into arm/dt
STM32 DT for v5.19, round 1
Highlights:
----------
-MCU:
-Fix pinctrl node names to match with pinctrl yaml.
- MPU:
-General:
- Fix pinctrl node names to match with pinctrl yaml.
- Add Protonics boards support based on STM32MP151A SoC:
- PRTT1C - 10BaseT1L switch: mainly embeds a sja1105q switch with
TI and Micrel 10BaseT Phys and wifi support.
- PRTT1S - 10BaseT1L CO2 sensor board: mainly embeds I2C humidity
and CO2 sensors.
- PRTT1A - 10BaseT1L multi functional controller.
- ST boards:
- Add RTC support on stm32mp13.
- Add button and heartbit support on stm32mp13 DK board.
- Add a secure version of STM32MP15 ED1/EV1/DK1/DK2 boards based
on OP-TEE OS and SCMI protocol.
- DH boards:
- Use MCO2 to generate PHY clock and ETHRX clock in order to release
internal PLL for a better SD card usage.
- Add 1ms PHY post-reset on Avenger96 board to match with PHY
requirements.
* tag 'stm32-dt-for-v5.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32: (24 commits)
ARM: dts: stm32: Add SCMI version of STM32 boards (DK1/DK2/ED1/EV1)
dt-bindings: arm: stm32: Add SCMI version of STM32 boards (DK1/DK2/ED1/EV1)
ARM: dts: stm32: enable optee firmware and SCMI support on STM32MP15
dt-bindings: reset: stm32mp15: rename RST_SCMI define
dt-bindings: clock: stm32mp15: rename CK_SCMI define
dt-bindings: clock: stm32mp1: describes clocks if "st,stm32mp1-rcc-secure"
dt-bindings: rcc: Add optional external ethernet RX clock properties
ARM: dts: stm32: add UserPA13 button on stm32mp135f-dk
ARM: dts: stm32: add blue led (Linux heartbeat) on stm32mp135f-dk
ARM: dts: stm32: add EXTI interrupt-parent to pinctrl node on stm32mp131
ARM: dts: stm32: add support for Protonic PRTT1x boards
ARM: dts: stm32: stm32mp15-pinctrl: add spi1-1 pinmux group
dt-bindings: net: silabs,wfx: add prt,prtt1c-wfm200 antenna variant
dt-bindings: arm: stm32: Add compatible strings for Protonic T1L boards
dt-bindings: arm: stm32: correct blank lines
dt-bindings: arm: stm32: narrow DH STM32MP1 SoM boards
ARM: dts: stm32: enable RTC support on stm32mp135f-dk
ARM: dts: stm32: add RTC node on stm32mp131
ARM: dts: stm32: Fix PHY post-reset delay on Avenger96
ARM: dts: stm32: fix pinctrl node name warnings (MPU soc)
...
Link: https://lore.kernel.org/r/5818c943-882d-7e50-430d-ae3299a108ee@foss.st.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add support for the i.MX7D SMEGW01 board.
This is a gateway board that supports the following peripherals:
- eMMC / SD card
- RTC
- USB modem
- Wifi via SDIO
- Dual Ethernet
- CAN
- Serial SRAM
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Attempting to boot my Udoo Dual and Quad with mainline hangs during boot
after printing:
[ 3.270471] imx_usb 2184000.usb: No over current polarity defined
[ 3.922502] mxs_phy 20c9000.usbphy: Data pin can't make good contact.
[ 3.940097] imx_usb 2184200.usb: No over current polarity defined
where imx_usb 2184200.usb is usbh1 in the DT. Adding debug prints to the
code seems to show that we lock up at the first read in usbmisc_imx6q_init()
which in combination with the above logging about the USB controllers
suggests that we lock up on the first read in usbmisc_imx6q_init(). Looking
at some of the other i.MX6 boards and the warning messages that are being
printed suggests that there is bitrot in the DTS for the device so disable
it for now, with it disabled the board boots successfully. Clearly this is
not a real fix, but it does allow some use of the board with mainline.
Similar behaviour is seen all the way back as far as v4.19, I tried going
back to when the board was added but had toolchain issues. Vendor provided
binaries seem fine on the boards so it seems likely that the hardware is
fine and the issue is with some combination of the DT and kernel. This
should obviously be resolved properly but for now this at least allows
the kernel to boot with reduced functionality on these systems.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The '#dma-channels' property was deprecated in favor of one defined by
generic dma-common DT bindings.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This allows boards the option of adding properties or disabling the
LEDs entirely.
Signed-off-by: Alexander Shiyan <eagle.alexander923@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Reduce the interrupt-map-mask of the external interrupt controller to
7 to align with the devicetree schema.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add a label for the cpu node, so that board devicetree files can
reference to the CPU node.
This is useful for describing a PMIC voltage that supplies the CPU
voltage.
For example:
&cpu0 {
cpu-supply = <&sw1_reg>;
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The usage of the 'fsl,uart-has-rtscts' property is deprecated.
Use the standard 'uart-has-rtscts' instead.
Cc: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The usage of the 'fsl,uart-has-rtscts' property is deprecated.
Use the standard 'uart-has-rtscts' instead.
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The binding of ifc device has been updated. Update dts to match
accordingly.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add a "secure" version based on SCMI of STM32 boards. Only boards
provided by STMicroelectronics are concerned:
-STM32MP157A-DK1
-STM32MP157C-DK2
-STM32MP157C-ED1
-STM32MP157C-EV1
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
The pl330 DMA controller provides number of DMA channels and requests
through its registers, so duplicating this information (with a chance of
mistakes) in DTS is pointless. Additionally the DTS used always wrong
property names which causes DT schema check failures - the bindings
documented 'dma-channels' and 'dma-requests' properties without leading
hash sign.
Reported-by: Rob Herring <robh@kernel.org>
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220430121902.59895-3-krzysztof.kozlowski@linaro.org
The pl330 DMA controller provides number of DMA channels and requests
through its registers, so duplicating this information (with a chance of
mistakes) in DTS is pointless. Additionally the DTS used always wrong
property names which causes DT schema check failures - the bindings
documented 'dma-channels' and 'dma-requests' properties without leading
hash sign.
Reported-by: Rob Herring <robh@kernel.org>
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20220430121902.59895-2-krzysztof.kozlowski@linaro.org
The pl330 DMA controller provides number of DMA channels and requests
through its registers, so duplicating this information (with a chance of
mistakes) in DTS is pointless. Additionally the DTS used always wrong
property names which causes DT schema check failures - the bindings
documented 'dma-channels' and 'dma-requests' properties without leading
hash sign.
Reported-by: Rob Herring <robh@kernel.org>
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220430121902.59895-8-krzysztof.kozlowski@linaro.org
The pl330 DMA controller provides number of DMA channels and requests
through its registers, so duplicating this information (with a chance of
mistakes) in DTS is pointless. Additionally the DTS used always wrong
property names which causes DT schema check failures - the bindings
documented 'dma-channels' and 'dma-requests' properties without leading
hash sign.
Reported-by: Rob Herring <robh@kernel.org>
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220430121902.59895-7-krzysztof.kozlowski@linaro.org
Buffalo WZR-1166DHP/WZR-1166DHP2 wireless router with
- BCM4708A0
- 128MiB NAND flash
- 2T2R 11ac/a/b/g/n Wi-Fi
- 4x 10/100/1000M ethernet switch
- 1x USB 3.0 port
WZR-1166DHP and WZR-1166DHP2 have different memory capacity.
WZR-1166DHP
- 512 MiB DDR2 SDRAM
WZR-1166DHP2
- 256 MiB DDR2 SDRAM
These hardware components are very similar to the WZR-1750DHP
except for the number of antennas.
Signed-off-by: SHIMAMOTO Takayoshi <takayoshi.shimamoto.360@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Those were removed from msm8974.dtsi as part of a recent cleanup commit,
so add them back for FP2.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220421214243.352469-3-luca@z3ntu.xyz
Set the relevant properties on the smbb charger to allow the device to
charge properly.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220421214243.352469-2-luca@z3ntu.xyz
Configure the touchscreen found on the new display module of the FP2.
To add some detail, FP2 has two different screen/touchscreen variants
("display module"), the old module has Synaptics touchscreen, the new
one this Ilitek touchscreen.
We're only supporting the new display module for now.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220421214243.352469-1-luca@z3ntu.xyz
This device node is unused now that we've removed the driver that
consumed it in the kernel. Drop the unused node to save some space.
Cc: Alex Elder <elder@linaro.org>
Cc: Taniya Das <quic_tdas@quicinc.com>
Cc: Mike Tipton <quic_mdtipton@quicinc.com>
Cc: Georgi Djakov <djakov@kernel.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220415005828.1980055-2-swboyd@chromium.org
The PA13 user button is connected to the PA13 pin of the stm32mp135f-dk
board. It requires an internal pull-up configuration.
Signed-off-by: Fabien Dessenne <fabien.dessenne@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
The blue led (Linux heartbeat) is connected to the PA14 pin of the
stm32mp135f-dk board.
Signed-off-by: Fabien Dessenne <fabien.dessenne@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
- New devicetree for Codina TMO (SGH-T599).
- Add the Amastaos proximity sensor to the Codina.
- Add line impedance per machine to the Fuel Gauge
nodes.
- Add GPS to Janice, Skomer and Codina.
- Add NFC to the Codina for GT-I8160P.
- Some janitorial like clock names.
-----BEGIN PGP SIGNATURE-----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=izAF
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=vs0V
-----END PGP SIGNATURE-----
Merge tag 'ux500-dts-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into arm/dt
Ux500 DTS updates for the v5.19 kernel cycle:
- New devicetree for Codina TMO (SGH-T599).
- Add the Amastaos proximity sensor to the Codina.
- Add line impedance per machine to the Fuel Gauge
nodes.
- Add GPS to Janice, Skomer and Codina.
- Add NFC to the Codina for GT-I8160P.
- Some janitorial like clock names.
* tag 'ux500-dts-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: dts: ux500: Add GPS to the Codina
ARM: dts: ux500: Add NFC to the Codina
ARM: dts: ux500: Add GPS to Skomer device tree
ARM: dts: ux500: Add GPS to Janice device tree
ARM: dts: ux500: Add line impedance to fuel gauge
ARM: dts: ux500: Register Amstaos proximity sensor
ARM: dts: ux500: Add Codina TMO device tree
dt-bindings: arm: ux500: Document Codina-TMO
ARM: dts: ste-dbx: Update spi clock-names property
Link: https://lore.kernel.org/r/CACRpkdYngWscqak5phKm58O2GF0RmVETgwW4NCKTBiASdaEcyg@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Devicetree changes for omaps:
- A series of changes to fix devicetree binding check warnings for omaps
the the use of clock-output-names and clksel bindings
- Update Ethernet node names for omaps
- Pinctrl updates for logicpd-som-lv
- A series of updates for am335x-guardian
- Regulator range update for am335x-baltos
Note that this branch is based on a upstream IOMMU fix as it's needed for
booting on some SoCs.
-----BEGIN PGP SIGNATURE-----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=SjMo
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEo6/YBQwIrVS28WGKmmx57+YAGNkFAmJxLXYACgkQmmx57+YA
GNnZ0A/+PKCALJw72BCnvmBqlJEoQoiQ8MkIhV7SO7ayM6BmwchMOsFjr7pZeh4q
9FID9CuBt+tgtxvwzD49so9mnPNC2aQkNMnyj3dzHJbdvgKiIhp98xs7QvzgNKkv
/Tl6bl0dpYsLNmIDUab9lFKR6foZNq6WijDTnxWGiUeDt9bVcowuKl/wySKkldqi
GSw4PXxDFjwlcPYz9PiSFKXAa5HEcnIwJi3+o9FpF5TY8POjkIP7ckE2Op5wyziW
Gek3PNrAsU7U2tZRYG5hhEoAy87yZb2ryHwsxzeu1v0YunV9OtivSBUNGB0FL2hz
MGB7j8qECi+Q9op43wTb5cae0NnghNwMzU2dpY5aMZXX6mIpfF8ZgfTnwXd81e2F
PlmpYKLrdoiAAJ82hVRHvQBl2HNyg9ZP9weXam6zZM5E2D6v7RhUWYyGlIORuZTp
y1Udkr9vwFkbdwP6rlym2odSboO0+jI1yflpMMUHcsGEePcC9iVK1gMXP4yPELzm
6d025VXNink+XETSlkN1gWtAYkYKV9wnr47MpEDNLPtLOipm6lXeXA8oj4rzeJmS
CDA1G0LCFOZpt7JkFViCeWbE+gDwZgKY4DjhhS3QCCSPM5ga8D0qOFAoEsZvzKfQ
1Y+jotDYZPP0CT/XgOB3+lB1WtFPhbGXhXgjGdckfzvMlP2kZ3U=
=lEpp
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.19/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dt
Devicetree changes for omaps
Devicetree changes for omaps:
- A series of changes to fix devicetree binding check warnings for omaps
the the use of clock-output-names and clksel bindings
- Update Ethernet node names for omaps
- Pinctrl updates for logicpd-som-lv
- A series of updates for am335x-guardian
- Regulator range update for am335x-baltos
Note that this branch is based on a upstream IOMMU fix as it's needed for
booting on some SoCs.
* tag 'omap-for-v5.19/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (29 commits)
ARM: dts: am335x-baltos: update MPU regulator range
ARM: dts: am335x: Guardian: Update comments
ARM: dts: am335x: Guardian: Add gpio line manes
ARM: dts: am335x: Guardian: Update interface pinmux
ARM: dts: am335x: Guardian: Disable DMA property of USB1
ARM: dts: am335x: Guardian: Enable UART port two
ARM: dts: am335x: Guardian: Update backlight parameter
ARM: dts: am335x: Guardian: Add lcd port
ARM: dts: am335x: Guardian: Update regulator node name
ARM: dts: am335x: Guardian: Update beeper label
ARM: dts: am335x: Guardian: Update life led
ARM: dts: am335x: Guardian: Remove mmc status led
ARM: dts: am335x: Guardian: Disable poweroff support from RTC
ARM: dts: am335x: Guardian: Add keypad
ARM: dts: am335x: Guardian: Rename power button label
ARM: dts: am335x: Guardian: Update NAND partition table
ARM: dts: logicpd-som-lv: Move pinmuxing to peripheral nodes
ARM: dts: omap3/4/5: fix ethernet node name for different OMAP boards
ARM: dts: Drop custom clkctrl compatible and update omap5 l4per
ARM: dts: Add clock-output-names for omap5
...
Link: https://lore.kernel.org/r/pull-1650961799-428630@atomide.com-2
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- ADC, SDHI, CAN-FD, I2C, QSPI, timer, watchdog, sound, USB, SPI, GPU,
cpufreq, and thermal support for the RZ/V2L SoC, and the RZ/V2L
SMARC EVK development board,
- USB, I2C, Audio, NOR Flash, timer, SPI support for RZ/G2LC SMARC EVK
development board,
- Can-FD support for the R-Car M30W+ and V3U SoCs, and the Falcon
development board,
- I2C and GPIO support for the R-Car S4-8 SoC,
- I2C EEPROM support for the Falcon development board,
- SPI Multi I/O Bus Controller (RPC-IF) support for the R-Car H3,
M3-W(+), M3-N, E3, and D3 SoCs,
- RPC HyperFlash support for the Draak, Ebisu, Salvator-X(S), and ULCB
development boards,
- Initial support (UART, DMAC, pin control, SDHI, eMMC, Ethernet) for
the RZ/G2UL SoC, and the RZ/G2UL SMARC EVK development board,
- Miscellaneous fixes and improvements.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCYmJ+7gAKCRCKwlD9ZEnx
cE5hAQDebyQdMMpgRgOC4ES3leIRrMJSmOAjrQcQjrTUJ6WYNgD9Gj8USqudA/By
Toz6dahFUSI0MDbgqnBjiqMGbEnbNww=
=xap2
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=SiTm
-----END PGP SIGNATURE-----
Merge tag 'renesas-arm-dt-for-v5.19-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/dt
Renesas ARM DT updates for v5.19
- ADC, SDHI, CAN-FD, I2C, QSPI, timer, watchdog, sound, USB, SPI, GPU,
cpufreq, and thermal support for the RZ/V2L SoC, and the RZ/V2L
SMARC EVK development board,
- USB, I2C, Audio, NOR Flash, timer, SPI support for RZ/G2LC SMARC EVK
development board,
- Can-FD support for the R-Car M30W+ and V3U SoCs, and the Falcon
development board,
- I2C and GPIO support for the R-Car S4-8 SoC,
- I2C EEPROM support for the Falcon development board,
- SPI Multi I/O Bus Controller (RPC-IF) support for the R-Car H3,
M3-W(+), M3-N, E3, and D3 SoCs,
- RPC HyperFlash support for the Draak, Ebisu, Salvator-X(S), and ULCB
development boards,
- Initial support (UART, DMAC, pin control, SDHI, eMMC, Ethernet) for
the RZ/G2UL SoC, and the RZ/G2UL SMARC EVK development board,
- Miscellaneous fixes and improvements.
* tag 'renesas-arm-dt-for-v5.19-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel: (55 commits)
ARM: dts: r9a06g032: Drop "arm,cortex-a7-timer" from timer node
arm64: dts: renesas: r8a779f0: Add GPIO nodes
arm64: dts: renesas: rzg2ul-smarc-som: Enable Ethernet on SMARC platform
arm64: dts: renesas: rzg2ul-smarc-som: Enable eMMC on SMARC platform
arm64: dts: renesas: rzg2ul-smarc: Enable microSD on SMARC platform
arm64: dts: renesas: r9a07g043: Add GbEthernet nodes
arm64: dts: renesas: r9a07g043: Add SDHI nodes
arm64: dts: renesas: rzg2ul-smarc: Add scif0 and audio clk pins
arm64: dts: renesas: r9a07g043: Fillup the pinctrl stub node
arm64: dts: renesas: Add initial device tree for RZ/G2UL Type-1 SMARC EVK
arm64: dts: renesas: Add initial DTSI for RZ/G2UL SoC
arm64: dts: renesas: rzg2l-smarc: Move gpios property of vccq_sdhi1 from common dtsi
arm64: dts: renesas: rzg2lc-smarc: Enable RSPI1 on carrier board
arm64: dts: renesas: ulcb: Add RPC HyperFlash device node
arm64: dts: renesas: salvator-common: Add RPC HyperFlash device node
arm64: dts: renesas: ebisu: Add RPC HyperFlash device node
arm64: dts: renesas: draak: Add RPC HyperFlash device node
arm64: dts: renesas: rcar-gen3: Add RPC device nodes
arm64: dts: renesas: rcar-gen4: Add interrupt properties to watchdog nodes
arm64: dts: renesas: rzg2: Add interrupt properties to watchdog nodes
...
Link: https://lore.kernel.org/r/cover.1650638505.git.geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The '#dma-channels' and '#dma-requests' properties were deprecated in
favor of these defined by generic dma-common DT bindings. Add new
properties while keeping old ones for backwards compatibility.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Message-Id: <20220503065201.51818-7-krzysztof.kozlowski@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The '#dma-channels' and '#dma-requests' properties were deprecated in
favor of these defined by generic dma-common DT bindings. Add new
properties while keeping old ones for backwards compatibility.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Message-Id: <20220503065201.51818-5-krzysztof.kozlowski@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The clksel related registers on omap3 cause unique_unit_address and
node_name_chars_strict warnings with the W=1 or W=2 make flags enabled.
With the clock drivers updated, we can now avoid most of these warnings
by grouping the TI component clocks using the TI clksel binding, and
with the use of clock-output-names property to avoid non-standard node
names for the clocks.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The clksel related registers on omap3 cause unique_unit_address and
node_name_chars_strict warnings with the W=1 or W=2 make flags enabled.
With the clock drivers updated, we can now avoid most of these warnings
by grouping the TI component clocks using the TI clksel binding, and
with the use of clock-output-names property to avoid non-standard node
names for the clocks.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The clksel related registers on omap3 cause unique_unit_address and
node_name_chars_strict warnings with the W=1 or W=2 make flags enabled.
With the clock drivers updated, we can now avoid most of these warnings
by grouping the TI component clocks using the TI clksel binding, and
with the use of clock-output-names property to avoid non-standard node
names for the clocks.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The clksel related registers on omap3 cause unique_unit_address and
node_name_chars_strict warnings with the W=1 or W=2 make flags enabled.
With the clock drivers updated, we can now avoid most of these warnings
by grouping the TI component clocks using the TI clksel binding, and
with the use of clock-output-names property to avoid non-standard node
names for the clocks.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The clksel related registers on omap3 cause unique_unit_address and
node_name_chars_strict warnings with the W=1 or W=2 make flags enabled.
With the clock drivers updated, we can now avoid most of these warnings
by grouping the TI component clocks using the TI clksel binding, and
with the use of clock-output-names property to avoid non-standard node
names for the clocks.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The clksel related registers on omap3 cause unique_unit_address and
node_name_chars_strict warnings with the W=1 or W=2 make flags enabled.
With the clock drivers updated, we can now avoid most of these warnings
by grouping the TI component clocks using the TI clksel binding, and
with the use of clock-output-names property to avoid non-standard node
names for the clocks.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The clksel related registers on omap3 cause unique_unit_address and
node_name_chars_strict warnings with the W=1 or W=2 make flags enabled.
With the clock drivers updated, we can now avoid most of these warnings
by grouping the TI component clocks using the TI clksel binding, and
with the use of clock-output-names property to avoid non-standard node
names for the clocks.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The clksel related registers on omap3 cause unique_unit_address and
node_name_chars_strict warnings with the W=1 or W=2 make flags enabled.
With the clock drivers updated, we can now avoid most of these warnings
by grouping the TI component clocks using the TI clksel binding, and
with the use of clock-output-names property to avoid non-standard node
names for the clocks.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The clksel related registers on omap3 cause unique_unit_address and
node_name_chars_strict warnings with the W=1 or W=2 make flags enabled.
With the clock drivers updated, we can now avoid most of these warnings
by grouping the TI component clocks using the TI clksel binding, and
with the use of clock-output-names property to avoid non-standard node
names for the clocks.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The clksel related registers on omap3 cause unique_unit_address and
node_name_chars_strict warnings with the W=1 or W=2 make flags enabled.
With the clock drivers updated, we can now avoid most of these warnings
by grouping the TI component clocks using the TI clksel binding, and
with the use of clock-output-names property to avoid non-standard node
names for the clocks.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The clksel related registers on omap3 cause unique_unit_address and
node_name_chars_strict warnings with the W=1 or W=2 make flags enabled.
With the clock drivers updated, we can now avoid most of these warnings
by grouping the TI component clocks using the TI clksel binding, and
with the use of clock-output-names property to avoid non-standard node
names for the clocks.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The clksel related registers on omap3 cause unique_unit_address and
node_name_chars_strict warnings with the W=1 or W=2 make flags enabled.
With the clock drivers updated, we can now avoid most of these warnings
by grouping the TI component clocks using the TI clksel binding, and
with the use of clock-output-names property to avoid non-standard node
names for the clocks.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The clksel related registers on omap3 cause unique_unit_address and
node_name_chars_strict warnings with the W=1 or W=2 make flags enabled.
With the clock drivers updated, we can now avoid most of these warnings
by grouping the TI component clocks using the TI clksel binding, and
with the use of clock-output-names property to avoid non-standard node
names for the clocks.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The clksel related registers on omap3 cause unique_unit_address and
node_name_chars_strict warnings with the W=1 or W=2 make flags enabled.
With the clock drivers updated, we can now avoid most of these warnings
by grouping the TI component clocks using the TI clksel binding, and
with the use of clock-output-names property to avoid non-standard node
names for the clocks.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The clksel related registers on omap3 cause unique_unit_address and
node_name_chars_strict warnings with the W=1 or W=2 make flags enabled.
With the clock drivers updated, we can now avoid most of these warnings
by grouping the TI component clocks using the TI clksel binding, and
with the use of clock-output-names property to avoid non-standard node
names for the clocks.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The clksel related registers on omap3 cause unique_unit_address and
node_name_chars_strict warnings with the W=1 or W=2 make flags enabled.
With the clock drivers updated, we can now avoid most of these warnings
by grouping the TI component clocks using the TI clksel binding, and
with the use of clock-output-names property to avoid non-standard node
names for the clocks.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The clksel related registers on omap3 cause unique_unit_address and
node_name_chars_strict warnings with the W=1 or W=2 make flags enabled.
With the clock drivers updated, we can now avoid most of these warnings
by grouping the TI component clocks using the TI clksel binding, and
with the use of clock-output-names property to avoid non-standard node
names for the clocks.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The clksel related registers on omap3 cause unique_unit_address and
node_name_chars_strict warnings with the W=1 or W=2 make flags enabled.
With the clock drivers updated, we can now avoid most of these warnings
by grouping the TI component clocks using the TI clksel binding, and
with the use of clock-output-names property to avoid non-standard node
names for the clocks.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The clksel related registers on omap3 cause unique_unit_address and
node_name_chars_strict warnings with the W=1 or W=2 make flags enabled.
With the clock drivers updated, we can now avoid most of these warnings
by grouping the TI component clocks using the TI clksel binding, and
with the use of clock-output-names property to avoid non-standard node
names for the clocks.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add appropriate firmware-name property for all am33xx platforms.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
[dfustini: change property from 'ti,scale-data-fw' to 'firmware-name']
Signed-off-by: Drew Fustini <dfustini@baylibre.com>
Message-Id: <20220502021508.1342869-3-dfustini@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With this flag wkup_m3 is able to control IO isolation during
suspend on the board.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Drew Fustini <dfustini@baylibre.com>
Message-Id: <20220502021508.1342869-2-dfustini@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This boards are based on STM32MP151AAD3 and use 10BaseT1L for communication.
- PRTT1C - 10BaseT1L switch
- PRTT1S - 10BaseT1L CO2 sensor board
- PRTT1A - 10BaseT1L multi functional controller
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
This reverts commit 0dc23d1a8e, which caused another regression
as the pinctrl code actually expects an integer value of 0 or 1
rather than a simple boolean property.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch replaces the legacy partition table layout with a modern style.
As an additional change, we are reserving space for three backup MLO entries
and increasing space for the main bootloader.
Signed-off-by: Alexander Shiyan <eagle.alexander923@gmail.com>
Message-Id: <20220427081914.6773-2-eagle.alexander923@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The CPU RTC has an external crystal, so to keep time, let's define
it for devicetree.
Signed-off-by: Alexander Shiyan <eagle.alexander923@gmail.com>
Message-Id: <20220427081914.6773-1-eagle.alexander923@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
All other msm8974 dts files are licensed as GPL-2.0 so add the same
header to the files where it's missing.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220421211936.345168-3-luca@z3ntu.xyz
Without '#power-domain-cells' property, power-domains cannot
be used. This property is noted required in the device-tree
binding.
Add '#power-domain-cells' as needed.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Link: https://lore.kernel.org/r/20220422120850.769480-6-herve.codina@bootlin.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add reset control properties into MDIO nodes. The 4 MDIO controllers in
AST2600 SOC share one reset control bit SCU50[3].
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The VBUS on usbotg is connected to the PMIC SWBST, let's reflect
that in the bindings.
Signed-off-by: Alexander Shiyan <eagle.alexander923@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch updates the PMIC voltages according to the module's
datasheet to match both commercial and industrial variants of the module.
Signed-off-by: Alexander Shiyan <eagle.alexander923@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
VGEN1, VGEN2 and GPO1 regulators are not used on SOM.
Let's remove these entries.
Signed-off-by: Alexander Shiyan <eagle.alexander923@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The LS1021A-IoT gateway reference design is a purpose-built,
small footprint hardware platform equipped with a wide array
of both high-speed connectivity and low speed serial interfaces.
CC: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Changming Huang <jerry.huang@nxp.com>
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Latest version of ti,tmp103 driver supports thermal zone. So make use of
it.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
X axis is not inverted in hardware.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Factor out common parts of vicut1 and vicutp to reduce maintenance
overhead.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The common base is now identical to imx6qdl-vicut1.dtsi, so we can remove
one of both.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This commit will finally make this file identical to imx6qdl-victgo.dtsi.
All nodes that are removed here are added as-is to the DTS files that
include this file.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
These parts are common to imx6qdl-vicut1.dtsi.
This patch is preparation to unify victgo and vicut1 DTs.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Following changes was made:
- Add MDIO signal names
- Add missing ISB_IN2 name. Also correct ISB_nIN1. These two signals were used
together in older HW revisions. Later ISB_IN2 was removed. Software should
still be able to use both.
- Add missing CAN1 and UART line names
- Add missing ON1/2_CTRL line names
- fix CPU_* line names. The real signal names are without the CPU_ prefix, like
on imx6qdl-vicut1.dtsi
- Fix ETH_INT signal name
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Only the prototype had the SATA interface. There are no existing products
with SATA interface and no plans to add any.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The function of DISP0_DAT9 is dependent on hardware revision of two
particular variants. This setting should be done by the bootloader anyway,
and is not needed in the kernel, so remove it from the DT.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add some missing names and remove names to pins that have never been used
and/or are not present on any hardware.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
While there are LEDs connected on some variants on GPIO4 pins 16 and 17,
those are not the debug LEDs that should be visible to user-space.
It should be the same as in imx6dl-victgo.dtsi.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The names should be consistent with the names in imx6dl-victgo.dts
This patch is preparation to unify vicut1 and victgo DTs.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Only first prototype had UART2 and there are no plans to add it in the
future.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Only the very first prototypes had PCIe and there are no plant to add it
in the future.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Unify nON_SWITCH pinctrl configuration with imx6dl-victgo.dts.
This patch is a preparation to reduce duplicated code between vicut1 and
victgo.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Only the first prototypes had a TiWi module. There is no publicly available
hardware where this module is fitted and there are no plan to produce
any.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The correct spelling for the property is gpios. Otherwise, the regulator
will neither reserve nor control any GPIOs. Thus, any SD/MMC card which
can use UHS-I modes will fail.
Fixes: c2e4987e0e ("ARM: dts: imx6ull: add Toradex Colibri iMX6ULL support")
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add dts for ARMv7 based broadband SoC BCM47622. bcm47622.dtsi is the
SoC description dts header and bcm947622.dts is a simple dts file for
Broadcom BCM947622 Reference board that only enable the UART port.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Vendor prefix in compatible should be lower-case and the jedec,spi-nor
should be used as fallback, according to the bindings.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20220420090247.73410-2-krzysztof.kozlowski@linaro.org
The node names should be generic and SPI NOR dtschema expects "flash".
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Link: https://lore.kernel.org/r/20220420090247.73410-1-krzysztof.kozlowski@linaro.org
1. Several DT schema related changes to make DTBs passing schema checks:
EHCI/OHCI/DMA/Ethernet node names, DMA channels order, USB-like
compatibles.
2. Add specific compatibles to Multi Core Timer to allow stricter DT
schema matching.
3. Cleanup from deprecated bindings:
- Remove deprecated unit-address workaround for Exynos5422 Odroid XU3
LPDDR3 memory timings.
- Do not use unit-address (and SFR region) in Exynos5250 MIPI phy in
favor of syscon node (unit-address deprecated in 2016).
- Use standard generic PHYs for EHCI/OHCI device in S5PV210.
4. Fix inverted SPI CS (thus blank panel) on S5PV210 Aries boards.
5. Correct Bluetooth interupt name on S5PV210 Aries boards.
-----BEGIN PGP SIGNATURE-----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=DEWZ
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=P83E
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/dt
Samsung DTS ARM changes for v5.19
1. Several DT schema related changes to make DTBs passing schema checks:
EHCI/OHCI/DMA/Ethernet node names, DMA channels order, USB-like
compatibles.
2. Add specific compatibles to Multi Core Timer to allow stricter DT
schema matching.
3. Cleanup from deprecated bindings:
- Remove deprecated unit-address workaround for Exynos5422 Odroid XU3
LPDDR3 memory timings.
- Do not use unit-address (and SFR region) in Exynos5250 MIPI phy in
favor of syscon node (unit-address deprecated in 2016).
- Use standard generic PHYs for EHCI/OHCI device in S5PV210.
4. Fix inverted SPI CS (thus blank panel) on S5PV210 Aries boards.
5. Correct Bluetooth interupt name on S5PV210 Aries boards.
* tag 'samsung-dt-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: s5pv210: align DMA channels with dtschema
ARM: dts: s5pv210: Adjust DMA node names to match spec
ARM: dts: s5pv210: Adjust memory reg entries to match spec
ARM: dts: s5pv210: Correct interrupt name for bluetooth in Aries
ARM: dts: s5pv210: Remove spi-cs-high on panel in Aries
ARM: dts: s5pv210: Use standard arrays of generic PHYs for EHCI/OHCI device
ARM: dts: s5pv210: align EHCI/OHCI nodes with dtschema
ARM: dts: exynos: align EHCI/OHCI nodes with dtschema on Exynos4
ARM: dts: exynos: drop deprecated SFR region from MIPI phy
ARM: dts: exynos: add a specific compatible to MCT
ARM: dts: exynos: remove deprecated unit address for LPDDR3 timings on Odroid
ARM: dts: exynos: fix compatible strings for Ethernet USB devices
ARM: dts: exynos: fix ethernet node name for different odroid boards
Link: https://lore.kernel.org/r/20220420072152.11696-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Few regression fixes for omap variants. These mostly fix issues related to
warnings added for system suspend, and some devicetree issues:
- Make ti-sysc driver quirks for gpt12 timer omap3 specific to fix
timer clock disabling for am335x system suspend
- Fix new system suspend warning for dra7 vpe caused by trying to
use register bits not wired for vpe
- Fix mmc boot order for omap3-gta04 that has no mmc2 or 3 wired
- Add missing touchscreen properties for am3
- Fix pin muxing for logicpd-som-lv and am3517-evm to not depend on
earlier bootloader versions
- Fix refcount leak for omap_gic_of_init
-----BEGIN PGP SIGNATURE-----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=ENHQ
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=qg1e
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.18/fixes-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Fixes for omaps
Few regression fixes for omap variants. These mostly fix issues related to
warnings added for system suspend, and some devicetree issues:
- Make ti-sysc driver quirks for gpt12 timer omap3 specific to fix
timer clock disabling for am335x system suspend
- Fix new system suspend warning for dra7 vpe caused by trying to
use register bits not wired for vpe
- Fix mmc boot order for omap3-gta04 that has no mmc2 or 3 wired
- Add missing touchscreen properties for am3
- Fix pin muxing for logicpd-som-lv and am3517-evm to not depend on
earlier bootloader versions
- Fix refcount leak for omap_gic_of_init
* tag 'omap-for-v5.18/fixes-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: logicpd-som-lv: Fix wrong pinmuxing on OMAP35
ARM: dts: am3517-evm: Fix misc pinmuxing
ARM: dts: am33xx-l4: Add missing touchscreen clock properties
ARM: dts: Fix mmc order for omap3-gta04
ARM: dts: dra7: Fix suspend warning for vpe powerdomain
bus: ti-sysc: Make omap3 gpt12 quirk handling SoC specific
ARM: OMAP2+: Fix refcount leak in omap_gic_of_init
iommu/omap: Fix regression in probe for NULL pointer dereference
Link: https://lore.kernel.org/r/pull-1650543308-836725@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Update the max MPU voltage range to align with the maximum
possible value allowed in the operating-points table, which is max
target voltage of 132500 uV + 2%.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Message-Id: <20220419143923.25196-1-yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* assign name to gpio line
Signed-off-by: Gireesh Hiremath <Gireesh.Hiremath@in.bosch.com>
Message-Id: <20220325100613.1494-15-Gireesh.Hiremath@in.bosch.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* Add support for uart2 port
Signed-off-by: Gireesh Hiremath <Gireesh.Hiremath@in.bosch.com>
Message-Id: <20220325100613.1494-12-Gireesh.Hiremath@in.bosch.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* Update default brightness and dimming frequency
* Enable current sink, while initialization
Signed-off-by: Gireesh Hiremath <Gireesh.Hiremath@in.bosch.com>
Message-Id: <20220325100613.1494-11-Gireesh.Hiremath@in.bosch.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* Add port to the node lcdc
Signed-off-by: Gireesh Hiremath <Gireesh.Hiremath@in.bosch.com>
Message-Id: <20220325100613.1494-10-Gireesh.Hiremath@in.bosch.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* update life led label and pin number
Signed-off-by: Gireesh Hiremath <Gireesh.Hiremath@in.bosch.com>
Message-Id: <20220325100613.1494-7-Gireesh.Hiremath@in.bosch.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* Disabling poweroff support form RTC will allow poweroff
to handle from other machanism
Signed-off-by: Gireesh Hiremath <Gireesh.Hiremath@in.bosch.com>
Message-Id: <20220325100613.1494-5-Gireesh.Hiremath@in.bosch.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* Update partition table to save env and splash image
* GPMC config values optimized for Bosch Guardian Board
* NAND Chip used by Bosch Guardian Board is Micron MT29F4G08ABBFA
Signed-off-by: Gireesh Hiremath <Gireesh.Hiremath@in.bosch.com>
Message-Id: <20220325100613.1494-2-Gireesh.Hiremath@in.bosch.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move some pinmux references to their respective peripherals.
This keeps the pins in safe-mode until they are requested.
Signed-off-by: Adam Ford <aford173@gmail.com>
Message-Id: <20220303171818.11060-2-aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The node name of Ethernet controller should be "ethernet" instead of
"usbether" as required by Ethernet controller devicetree schema:
Documentation/devicetree/bindings/net/ethernet-controller.yaml
This patch can potentially affect boot loaders patching against full
node path instead of using device aliases.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Message-Id: <20220216074927.3619425-8-o.rempel@pengutronix.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Clean up and commonize (where possible and it makes sense to) I2C, UART
and SDHCI nodes and pin configurations.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220415115633.575010-20-konrad.dybcio@somainline.org
- Remove regulators from the SoC DTSI
- cpu_pmu{} -> pmu{}
- move modem/iris regulators out of here; only FP2 used them
- tcsr_mutex is moved out of /soc
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
[bjorn: Rebased on top of Krzysztof's fixes]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220415115633.575010-18-konrad.dybcio@somainline.org
