Brings it closer to more serious actions (adding branching
and allowing for late binding)
Unfortunately this breaks old syntax of the simple action.
But because simple is a pedagogical example unlikely to be used
in production environments (i.e its role is to serve as an example
on how to write actions), then this is ok.
New syntax for simple has new keyword "sdata". Example usage is:
sudo tc actions add action simple sdata "foobar" index 1
or
tc filter add dev $DEV parent ffff: protocol ip prio 1 u32\
match ip dst 17.0.0.1/32 flowid 1:10 action simple sdata "foobar"
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
This action allows for a sending side to encapsulate arbitrary metadata
which is decapsulated by the receiving end.
The sender runs in encoding mode and the receiver in decode mode.
Both sender and receiver must specify the same ethertype.
At some point we hope to have a registered ethertype and we'll
then provide a default so the user doesnt have to specify it.
For now we enforce the user specify it.
Described in netdev01 paper:
"Distributing Linux Traffic Control Classifier-Action Subsystem"
Authors: Jamal Hadi Salim and Damascene M. Joachimpillai
Also refer to IETF draft-ietf-forces-interfelfb-04.txt
Lets show example usage where we encode icmp from a sender towards
a receiver with an skbmark of 17; both sender and receiver use
ethertype of 0xdead to interop.
YYYY: Lets start with Receiver-side policy config:
xxx: add an ingress qdisc
sudo tc qdisc add dev $ETH ingress
xxx: any packets with ethertype 0xdead will be subjected to ife decoding
xxx: we then restart the classification so we can match on icmp at prio 3
sudo $TC filter add dev $ETH parent ffff: prio 2 protocol 0xdead \
u32 match u32 0 0 flowid 1:1 \
action ife decode reclassify
xxx: on restarting the classification from above if it was an icmp
xxx: packet, then match it here and continue to the next rule at prio 4
xxx: which will match based on skb mark of 17
sudo tc filter add dev $ETH parent ffff: prio 3 protocol ip \
u32 match ip protocol 1 0xff flowid 1:1 \
action continue
xxx: match on skbmark of 0x11 (decimal 17) and accept
sudo tc filter add dev $ETH parent ffff: prio 4 protocol ip \
handle 0x11 fw flowid 1:1 \
action ok
xxx: Lets show the decoding policy
sudo tc -s filter ls dev $ETH parent ffff: protocol 0xdead
xxx:
filter pref 2 u32
filter pref 2 u32 fh 800: ht divisor 1
filter pref 2 u32 fh 800::800 order 2048 key ht 800 bkt 0 flowid 1:1 (rule hit 0 success 0)
match 00000000/00000000 at 0 (success 0 )
action order 1: ife decode action reclassify type 0x0
allow mark allow prio
index 11 ref 1 bind 1 installed 45 sec used 45 sec
Action statistics:
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
xxx:
Observe that above lists all metadatum it can decode. Typically these
submodules will already be compiled into a monolithic kernel or
loaded as modules
YYYY: Lets show the sender side now ..
xxx: Add an egress qdisc on the sender netdev
sudo tc qdisc add dev $ETH root handle 1: prio
xxx:
xxx: Match all icmp packets to 192.168.122.237/24, then
xxx: tag the packet with skb mark of decimal 17, then
xxx: Encode it with:
xxx: ethertype 0xdead
xxx: add skb->mark to whitelist of metadatum to send
xxx: rewrite target dst MAC address to 02:15:15:15:15:15
xxx:
sudo $TC filter add dev $ETH parent 1: protocol ip prio 10 u32 \
match ip dst 192.168.122.237/24 \
match ip protocol 1 0xff \
flowid 1:2 \
action skbedit mark 17 \
action ife encode \
type 0xDEAD \
allow mark \
dst 02:15:15:15:15:15
xxx: Lets show the encoding policy
filter pref 10 u32
filter pref 10 u32 fh 800: ht divisor 1
filter pref 10 u32 fh 800::800 order 2048 key ht 800 bkt 0 flowid 1:2 (rule hit 118 success 0)
match c0a87a00/ffffff00 at 16 (success 0 )
match 00010000/00ff0000 at 8 (success 0 )
action order 1: skbedit mark 17
index 11 ref 1 bind 1 installed 3 sec used 3 sec
Action statistics:
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
action order 2: ife encode action pipe type 0xDEAD
allow mark dst 02:15:15:15:15:15
index 12 ref 1 bind 1 installed 3 sec used 3 sec
Action statistics:
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
xxx:
Now test by sending ping from sender to destination
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Since we can only configure unicast, we probably want to be able to
display unicast, rather than multicast.
Fixes: 906ac5437a ("geneve: add support for IPv6 link partners")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Display only attributes that are relevant when a GRE interface is in
'external' mode instead of the default values (which are ignored by the
kernel even if passed back).
Fixes: 926b39e1fe ("gre: add support for collect metadata flag")
Signed-off-by: Jiri Benc <jbenc@redhat.com>
For GRE interfaces in 'external' mode, the kernel ignores all manual
settings like remote IP address or TTL. However, for some of those
attributes, kernel checks their value and does not allow them to be zero
(even though they're ignored later).
Currently, 'ip link' always includes all attributes in the netlink message.
This leads to problem with creating interfaces in 'external' mode. For
example, this command does not work:
ip link add gre1 type gretap external
and needs a bogus remote IP address to be specified, as the kernel enforces
remote IP address to be either not present, or not null.
Ignore the parameters that do not make sense in 'external' mode.
Unfortunately, we cannot error out, as there may be existing deployments
that workarounded the bug by specifying bogus values.
Fixes: 926b39e1fe ("gre: add support for collect metadata flag")
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Add function for command completion for tc in bash, and update Makefile
to install it under /usr/share/bash-completion/completions/.
Inside iproute2 repository, the completion code is in a new
`bash-completion` toplevel directory.
v2: Remove `if` statement in Makefile: do not try to install in
/etc/bash_completion.d/ if /usr/share/bash-completion/completions/
is not found; instead, the user can override the installation path
with the specific environment variable.
Signed-off-by: Quentin Monnet <quentin.monnet@6wind.com>
SK_MEMINFO_DROPS is added in linux-4.7 for TCP, UDP and SCTP
skmem will display the socket drop count using d prefix as in :
$ ss -tm src :22 | more
State Recv-Q Send-Q Local Address:Port Peer Address:Port
ESTAB 0 52 10.246.7.151:ssh 172.20.10.101:50759
skmem:(r0,rb8388608,t0,tb8388608,f1792,w2304,o0,bl0,d0)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Use kernel shared buffer occupancy control commands to make snapshot and
clear occupancy watermarks. Also, allow to show occupancy values in a
nice way.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Implement kernel devlink shared buffer interface. Introduce new object
"sb" and allow to browse the shared buffer parameters and also change
configuration.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
This function is to be used from dump callbacks to decide if the output
currect output should be filtered off or not. Filtering is based on
previously parsed and stored command line options.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
It is handy to have parsed cmdline data stored so they can be used for
dumps filtering. So split original dl_argv_parse_put into parse and put
parts.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Kernel sets info->tcpi_min_rtt to ~0U when no RTT sample was ever
taken for the session, thus min_rtt is unknown.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Passing a filter expression and selecting an address family using the
'-f' flag would overwrite the state filter by accident. Therefore
calling e.g. 'ss -nl -f inet '(sport = :22)' would not only print
listening sockets (as requested by '-l' flag) but connected ones, as
well.
Fix this by reusing the formerly ineffective call to filter_states_set()
to restore the state filter as it was before the call to
filter_af_set().
Signed-off-by: Phil Sutter <phil@nwl.cc>
Use the same rtnl_dump_request_n call as the show. The rtnl_wilddump_request
assumes the type uses an ifinfomsg which is not the case for the neighbor
table.
Signed-off-by: Jeff Harris <jefftharris@gmail.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
It doesn't make sense to use external control plane and fill internal FDB at
the same time. It's even an illegal combination for VXLAN-GPE.
Just switch off learning when 'external' is specified.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
We need limits.h for PATH_MAX, fixes:
tc_bpf.c: In function ‘bpf_map_selfcheck_pinned’:
tc_bpf.c:222:12: error: ‘PATH_MAX’ undeclared (first use in this
function)
char file[PATH_MAX], buff[4096];
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Follow-up to kernel commit 6c9059817432 ("bpf: pre-allocate hash map
elements"). Add flags support, so that we can pass in BPF_F_NO_PREALLOC
flag for disallowing preallocation. Update examples accordingly and also
remove the BPF_* map helper macros from them as they were not very useful.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Make it easier to spot issues when loading the object file fails. This
includes reporting in what pinned object specs differ, better indication
when we've reached instruction limits. Don't retry to load a non relo
program once we failed with bpf(2), and report out of bounds tail call key.
Also, add truncation of huge log outputs by default. Sometimes errors are
quite easy to spot by only looking at the tail of the verifier log, but
logs can get huge in size e.g. up to few MB (due to verifier checking all
possible program paths). Thus, by default limit output to the last 4096
bytes and indicate that it's truncated. For the full log, the verbose option
can be used.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
