ip vrf exec requires root or CAP_NET_ADMIN, CAP_SYS_ADMIN and
CAP_DAC_OVERRIDE. It is not possible to run unprivileged commands like
ping as non-root or non-cap-enabled due to this requirement.
To allow users and administrators to safely add the required
capabilities to the binary, drop all capabilities on start if not
invoked with "vrf exec".
Update the manpage with the requirements.
Signed-off-by: Luca Boccassi <bluca@debian.org>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
This has to be a second match statement to the same u32 filter, not a
second one (which tc-filter doesn't support at all).
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
NTF_EXT_LEARNED can be set by a user on bridge fdb entry.
Provide a bridge command option to allow a user to set
NTF_EXT_LEARNED on a bridge fdb entry.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Add missing documentation of the memory_limit fq_codel parameter and the
ce_threshold codel and fq_codel parameters.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: David Ahern <dsahern@gmail.com>
Conflicts:
bridge/mdb.c
Updated bridge/bridge.c per removal of check_if_color_enabled by commit
1ca4341d2c ("color: disable color when json output is requested")
Signed-off-by: David Ahern <dsahern@gmail.com>
add support to match on ip_proto, sport and dport ranges.
For ip_proto, this patch currently enumerates, tcp, udp and sctp.
This list can be extended in the future.
example:
$ip rule add sport 666-777 dport 999 ip_proto tcp table 100
$ip rule show
0: from all lookup local
32765: from all ip_proto 6 sport 666-777 dport 999 lookup 100
32766: from all lookup main
32767: from all lookup default
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Modify 'ip rule' command to notice when the kernel passes
to us the originating protocol.
Add code to allow the `ip rule flush protocol XXX`
command to be accepted and properly handled.
Modify the documentation to reflect these code changes.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
The commit calls a new tc ematch for using netfilter xtable matches.
This allows early classification as well as mirroning/redirecting traffic
based on logic implemented in netfilter extensions.
Current supported use case is classification based on the incoming IPSec
state used during decpsulation using the 'policy' iptables extension
(xt_policy).
The matcher uses libxtables for parsing the input parameters.
Example use for matching an IPSec state with reqid 1:
tc qdisc add dev eth0 ingress
tc filter add dev eth0 protocol ip parent ffff: \
basic match 'ipt(-m policy --dir in --pol ipsec --reqid 1)' \
action drop
This is the user-space counter part of kernel commit ccc007e4a746
("net: sched: add em_ipt ematch for calling xtables matches")
Signed-off-by: Eyal Birger <eyal.birger@gmail.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
For IP-in-IP tunnels, one can specify the [no]allow-localremote command
when configuring a device. Under the hood, this flips the
IP6_TNL_F_ALLOW_LOCAL_REMOTE flag on the netdevice. However, ip6gretap
and ip6erspan devices, where the flag is also relevant, are not IP-in-IP
tunnels, and thus there's no way to configure the flag on these
netdevices. Therefore introduce the command to link_gre6 as well.
The original support was introduced in commit 21440d19d9
("ip: link_ip6tnl.c/ip6tunnel.c: Support IP6_TNL_F_ALLOW_LOCAL_REMOTE flag")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Implement an option (-b) to execute RDMAtool commands
from supplied file. This follows the same model as
in use for ip and devlink tools, by expecting
every new command to be on new line.
These commands are expected to be without any -*
(e.g. -d, -j, e.t.c) global flags, which should be
called externally.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Implement the -color option; in this case -co is ambiguous
since it was already used for -conf.
For now this just means putting device name in color.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David Ahern <dsahern@gmail.com>
Document color option, and no longer have restriction on json
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David Ahern <dsahern@gmail.com>
Make bridge work like other iproute2 commands and accept
same json and pretty flags.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David Ahern <dsahern@gmail.com>
Add description for -json and -pretty options.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David Ahern <dsahern@gmail.com>
If the kernel receives a negative nsid it will automatically assign
the next available nsid. In this case alloc_netid() will set min and
max to 0 for ird_alloc(). And when max == 0 idr_alloc() will interpret
this as the maximum range, i.e. specific to nsids it will try to find
an id in the range [0,INT_MAX). This is intentionally supported in the
kernel for nsids.
Commit acbe9118ce ("ip netns: use strtol() instead of atoi()")
regressed ip netns in that respect although previously the use-case
was either accidentally supported or opaquely supported such that it
triggered the original commit. From what I can gather it went as
follows before: atoi() was called with a string indicating a negative
value which caused it to return -1 which was passed to the
kernel. Let's make it less opaque by introducing the keyword "auto":
ip netns set <netns-name> auto
will cause nsid to be set to -1 and the kernel will select an available
nsid.
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Spartan version of resource tracking documentation.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
During qdisc creation it is possible to specify shared block for bot
ingress and egress. Pass this values to kernel according to the command
line options.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
So far, qdisc was the only handle that could be used to manipulate
filters. Kernel added support for using block to manipulate it. So add
the support to use block index to manipulate filters. The magic
TCM_IFINDEX_MAGIC_BLOCK indicates the block index is in use.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Zero value in min/max_tx_rate has a special meaning of no rate limit,
document it.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
netdevsim is a new software device for testing kernel APIs
without any hardware attached. Allow users to create such
devices.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Lintian detected the following formatting errors:
man/man8/devlink-sb.8.gz 230: warning: macro `b' not defined
man/man8/ip-link.8.gz 1243: warning: macro `in-8' not defined
(possibly missing space after `in')
man/man8/tc-u32.8.gz `R' is a string (producing the registered sign),
not a macro.
Signed-off-by: Luca Boccassi <bluca@debian.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
The filesytem paths to these scripts might be different on various
distros, so don't mention it in the manpages. It is not really useful
information anyway.
Originally submitted as Debian bug:
https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=561424
Reported-by: jidanni@jidanni.org
Signed-off-by: Luca Boccassi <bluca@debian.org>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Trying to set a label longer than 15 characters returns an error:
RTNETLINK answers: Numerical result out of range
Document the limit in the manpage.
Originally reported as a Debian bug:
https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=661886
Reported-by: Gabor Kiss <kissg@ssg.ki.iif.hu>
Signed-off-by: Luca Boccassi <bluca@debian.org>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
A Debian user suggested adding more network-related keywords to the
ip manpage, so that manpage-scraping and indexing software like
apropos can do a better job of categorizing the programs.
https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=877983
Suggested-by: Lynoure Braakman <lynoure@gmail.com>
Signed-off-by: Luca Boccassi <bluca@debian.org>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Documentation should be distribution-agnostic - any specific quirks
should be handled by downstream maintainers, if necessary.
Remove mentions of Debian paths and package names.
Signed-off-by: Luca Boccassi <bluca@debian.org>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
The patch adds support for configuring the erspan v2, for both
ipv4 and ipv6 erspan implementation. Three additional fields
are added: 'erspan_ver' for distinguishing v1 or v2, 'erspan_dir'
for specifying direction of the mirrored traffic, and 'erspan_hwid'
for users to set ERSPAN engine ID within a system.
As for manpage, the ERSPAN descriptions used to be under GRE, IPIP,
SIT Type paragraph. Since IP6GRE/IP6GRETAP also supports ERSPAN,
the patch removes the old one, creates a separate ERSPAN paragrah,
and adds an example.
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
veth and vxcan both create a vitual tunnel between a pair of virtual network
devices. This patch adds the content for the now supported vxcan netdevices
and the documentation to create peer devices for vxcan and veth.
Additional remove 'can' that accidently was on the list of link types which
can be created by 'ip link add' as 'can' devices are real network devices.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
v3:
Rebase and use out() instead of printf().
v2:
Print the path MTU immediately after the MSS, as it is easier to parse
for humans (suggested by Neal Cardwell).
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
The patch adds 'external' option to support collect metadata
gre6 tunnel. The 'external' keyword is already used to set the
device into collect metadata mode such as vxlan, geneve, ipip,
etc. This patch extends support for ipv6 gre and gretap.
Example of L3 and L2 gre device:
bash:~# ip link add dev ip6gre123 type ip6gre external
bash:~# ip link add dev ip6gretap123 type ip6gretap external
Signed-off-by: William Tu <u9012063@gmail.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Validate the upper limit for gso_max_size, valid range is [0-65,536]
inclusive. Fix minor whitespace in iplink man page.
Signed-off-by: Solio Sarabia <solio.sarabia@intel.com>
This allows sending GSO maximum values when configuring a device.
The values are advisory. Most devices will ignore them but for some
pseudo devices such as veth pairs they can be set.
Example:
# ip link add dev vm1 type veth peer name vm2 gso_max_size 32768
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Commit 6bbe5e6290 ("man: tc-csum.8: Fix example") changed both source
and destination IP addresses in example code but missed to update the
example's description accordingly.
Fixes: 6bbe5e6290 ("man: tc-csum.8: Fix example")
Signed-off-by: Phil Sutter <phil@nwl.cc>
For all files in iproute2 which do not have an obvious license
identification, mark them with SPDK GPL-2
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
This patch adapts the tc command line interface to allow bandwidth limits
to be specified as a percentage of the interface's capacity.
Adding this functionality requires passing the specified device string to
each class/qdisc which changes the prototype for a couple of functions: the
.parse_qopt and .parse_copt interfaces. The device string is a required
parameter for tc-qdisc and tc-class, and when not specified, the kernel
returns ENODEV. In this patch, if the user tries to specify a bandwidth
percentage without naming the device, we return an error from userspace.
Signed-off-by: Nishanth Devarajan<ndev2021@gmail.com>
This patch adds documentation for additional offload modes and
associated parameters in tc-mqprio.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
In order to calculate the idleSlope parameter of CBS correctly, users
must take into account the entire packet size, including the overhead
from all layers.
Add some more details to the man page to clarify that, giving one
simple example and pointing users to the correct 802.1Q section for
further clarifications if needed.
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
This patch adds fastopen_no_cookie option to enable/disable TCP fastopen
without a cookie on a per-route basis.
Support in Linux was added with 71c02379c762 (tcp: Configure TFO without
cookie per socket and/or per route).
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Christoph Paasch <cpaasch@apple.com>
IP6_TNL_F_ALLOW_LOCAL_REMOTE allows tunnel traffic on ip6tnl devices
where the remote endpoint is a local host address.
Specifying "[no]allow-localremote" controls the
IP6_TNL_F_ALLOW_LOCAL_REMOTE flag on ip6tnl interfaces.
This is the user-space counterpart for kernel
commit 908d140a87a7 ("ip6_tunnel: Allow rcv/xmit even if remote address is a local address")
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
This config maps to IFLA_BRPORT_VLAN_TUNNEL bridge port netlink
flag attribute. This flag enables vlan to tunnel mapping on a bridge
port. It is off by default.
set vlan_tunnel attribute on bridge port vxlan0:
$ip link set dev vxlan0 type bridge_slave vlan_tunnel on
$ip link set dev vxlan0 type bridge_slave vlan_tunnel off
or via bridge command
$bridge link set dev vxlan0 vlan_tunnel on
$bridge link set dev vxlan0 vlan_tunnel off
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Add detail explains of -m, -o, -e and -i options, which are not documented anywhere
Signed-off-by: yupeng <yupeng0921@gmail.com>
Acked-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Add neigh_suppress to the type help and document it in ip-link's man page.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
This patch adds the iproute2 support for getting and setting the
per-port group_fwd_mask. It also tries to resolve the value into a more
human friendly format by printing the known protocols instead of only
the raw value.
The man page is also updated with the new option.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
neigh suppression can be used to suppress arp and nd flood
to bridge ports. It maps to the recently added
kernel support for bridge port flag IFLA_BRPORT_NEIGH_SUPPRESS.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
The AF_VSOCK address family is a host<->guest communications channel
supported by VMware, KVM, and Hyper-V. Initial VMware support was
released in Linux 3.9 in 2013 and transports for other hypervisors were
added later.
AF_VSOCK addresses are <u32 cid, u32 port> tuples. The 32-bit cid
integer is comparable to an IP address. AF_VSOCK ports work like
TCP/UDP ports.
Both SOCK_STREAM and SOCK_DGRAM socket types are available.
This patch adds AF_VSOCK support to ss(8) so that sockets can be
observed.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This patch adds support to the iproute2 tc filter command for matching MPLS
labels in the flower classifier. The ability to match the Time To Live,
Bottom Of Stack, Traffic Control and Label fields are added as options to
the flower filter.
e.g.:
tc filter add dev eth0 protocol 0x8847 parent ffff: \
flower mpls_label 1 mpls_tc 2 mpls_ttl 3 mpls_bos 0 \
action drop
Signed-off-by: Benjamin LaHaise <benjamin.lahaise@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
This patch updates the tc-ife man page that the default IFE ethertype
will be used if it's not specified.
Signed-off-by: Alexander Aring <aring@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
There's some misleading information in --help and ss(8) manpage about
TCP-STATE named 'listen'.
ss doesn't know such a state, but it knows 'listening' state.
$ ss -tua state listen
ss: wrong state name: listen
$ ss -tua state listening
[...]
Addresses: https://bugs.debian.org/872990
Reported-by: Pavel Lyulchenko <p.lyulchenko@gmail.com>
Signed-off-by: Andreas Henriksson <andreas@fatal.se>
The patch adds ERSPAN type II tunnel support. The implementation is
based on the draft at
https://tools.ietf.org/html/draft-foschiano-erspan-01.
One of the purposes is for Linux box to be able to receive ERSPAN
monitoring traffic sent from the Cisco switch, by creating a ERSPAN
tunnel device. In addition, the patch also adds ERSPAN TX, so traffic
can also be encapsulated into ERSPAN and sent out.
The implementation reuses the key as ERSPAN session ID, and
field 'erspan' as ERSPAN Index fields:
./ip link add dev ers11 type erspan seq key 100 erspan 123 \
local 172.16.1.200 remote 172.16.1.100
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: Meenakshi Vohra <mvohra@vmware.com>
- CONTROL has to come last, otherwise 'index' applies to gact and not
simple itself.
- Man page wasn't updated to reflect syntax changes.
Signed-off-by: Phil Sutter <phil@nwl.cc>
In the presence of firewalls which improperly block ICMP Unreachable
(including Fragmentation Required) messages, Path MTU Discovery is
prevented from working.
The workaround is to handle IPv4 payloads opaquely, ignoring the DF
bit.
Kernel commit 22a59be8b7693eb2d0897a9638f5991f2f8e4ddd ("net: ipv4:
Add ability to have GRE ignore DF bit in IPv4 payloads") is
complemented by this user-space changeset which exposes control of
this setting.
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
This page is to highlight all operations and options that are
applicable to all tc actions.
Signed-off-by: Lucas Bates <lucasb@mojatatu.com>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Let XDP link set command request that the program be offloaded.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Allow user to select XDP DRV_MODE flag by using xdpdrv keyword
instead of xdp or xdpgeneric.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
As it turned out, forgetting to add a man page to the respective
Makefile when introducing it is a common mistake. Overcome this once and
for all by using $(wildcard) function in Makefiles.
Fixes: 7124942942 ("genl: add manpage")
Fixes: 958cd21094 ("ifcfg: add manpage")
Fixes: e1b7f883e5 ("man: add documentation for IPv6 SR commands")
Fixes: 1949f82cdf ("Introduce ip vrf command")
Fixes: 535194a172 ("tipc: add peer remove functionality")
Signed-off-by: Phil Sutter <phil@nwl.cc>
Allow users to set flower classifier filter rules which
include matches for ip tos and ttl.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Uses newly introduced RTM_GETROUTE flag RTM_F_FIB_MATCH
to return a matching fib route. Introduces 'fibmatch'
keyword to ip route get.
ipv4:
----
$ip route show
default via 192.168.0.2 dev eth0
10.0.14.0/24
nexthop via 172.16.0.3 dev dummy0 weight 1
nexthop via 172.16.1.3 dev dummy1 weight 1
$ip route get 10.0.14.2
10.0.14.2 via 172.16.1.3 dev dummy1 src 172.16.1.1
cache
$ip route get fibmatch 10.0.14.2
10.0.14.0/24
nexthop via 172.16.0.3 dev dummy0 weight 1
nexthop via 172.16.1.3 dev dummy1 weight 1
ipv6:
----
$ip -6 route show
2001:db9:100::/120 metric 1024
nexthop via 2001:db8:2::2 dev dummy0 weight 1
nexthop via 2001:db8:12::2 dev dummy1 weight 1
$ip -6 route get 2001:db9:100::1
2001:db9:100::1 from :: via 2001:db8:12::2 dev dummy1 \
src 2001:db8:12::1 metric 1024 pref medium
$ip -6 route get fibmatch 2001:db9:100::1
2001:db9:100::/120 metric 1024
nexthop via 2001:db8:12::2 dev dummy1 weight 1
nexthop via 2001:db8:2::2 dev dummy0 weight 1
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: David Ahern <dsahern@gmail.com>
Add to usage message a description of how to configure Infiniband node
and port GUIDs. Also modify the man page to emphasize the GUIDs are
configured for Infiniband VFs.
Fixes: d91fb3f4c7 ("Add support for configuring Infiniband GUIDs")
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
This is an e-switch global knob to enable HW support for applying
encapsulation/decapsulation to VF traffic as part of SRIOV e-switch offloading.
The actual encap/decap is carried out (along with the matching and other
actions) per offloaded e-switch rules, e.g as done when offloading the TC tunnel
key action.
Possible values are enable/disable.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Follow-up to commit c7272ca720 ("bpf: add initial support for
attaching xdp progs") to also support generic XDP. This adds an
indicator for loaded generic XDP programs when programs are loaded
as shown in c7272ca720, but the driver still lacks native XDP
support.
# ip link
[...]
3: eno1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 xdpgeneric qdisc [...]
link/ether 0c:c4:7a:03:f9:25 brd ff:ff:ff:ff:ff:ff
[...]
In case the driver does support native XDP, but the user wants
to load the program as generic XDP (e.g. for testing purposes),
then this can be done with the same semantics as in c7272ca720,
but with 'xdpgeneric' instead of 'xdp' command for loading:
# ip -force link set dev eno1 xdpgeneric obj xdp.o
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: David S. Miller <davem@davemloft.net>
For example, forward udp traffic destined to port 999 to veth0 and set
tcp port to 888:
$ tc filter add dev enp0s9 protocol ip parent ffff: \
flower \
ip_proto udp \
dst_port 999 \
action pedit ex munge \
udp dport set 888 \
action mirred egress \
redirect dev veth0
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Amir Vadai <amir@vadai.me>
For example, forward tcp traffic destined to port 80 to veth0 and set
tcp port to 8080:
$ tc filter add dev enp0s9 protocol ip parent ffff: \
flower \
ip_proto tcp \
dst_port 80 \
action pedit ex munge \
tcp dport set 8080 \
action mirred egress \
redirect dev veth0
Signed-off-by: Amir Vadai <amir@vadai.me>
For example, forward tcp traffic to veth0 and set
destination mac address to 11:22:33:44:55:66 :
$ tc filter add dev enp0s9 protocol ip parent ffff: \
flower \
ip_proto tcp \
action pedit ex munge \
eth dst set 11:22:33:44:55:66 \
action mirred egress \
redirect dev veth0
Signed-off-by: Amir Vadai <amir@vadai.me>
Enable user to edit IP header ttl field.
For example, to forward any TCP packet and decrease its TTL by one:
$ tc filter add dev enp0s9 protocol ip parent ffff: \
flower \
ip_proto tcp \
action pedit ex munge \
ip ttl add 0xff pipe \
action mirred egress \
redirect dev veth0
Signed-off-by: Amir Vadai <amir@vadai.me>
Utilize the extended pedit netlink to set an offset relative to a
specific header type. Old netlink only enabled the user to set
approximated offset relative to the IPv4 header.
To use this extended functionality need to use the 'ex' keyword after
'pedit' and before any 'munge'.
e.g:
$ tc filter add dev ens9 protocol ip parent ffff: \
flower \
ip_proto udp \
dst_port 80 \
action pedit ex munge \
ip dst set 1.1.1.1 \
pipe \
action mirred egress redirect dev veth0
Signed-off-by: Amir Vadai <amir@vadai.me>
Despite the past changes, users seemed to get confused by the seemingly
contradictory relation of priority value and actual rule priority.
Signed-off-by: Phil Sutter <phil@nwl.cc>
This patch adds information about seg6 encapsulation in the ip-route
manual, as well as the ip-sr manual page.
Signed-off-by: David Lebrun <david.lebrun@uclouvain.be>
Add support for setting and displaying the ttl attribute
for MPLS IP lighweight tunnels.
Signed-off-by: Robert Shearman <rshearma@brocade.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Add support for setting and displaying the ttl-propagation attribute
initially used by MPLS to control propagation of MPLS TTL to IPv4/IPv6
TTL/hop-limit on popping final label on a per-route basis.
Signed-off-by: Robert Shearman <rshearma@brocade.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
While generating PDFs from the man pages, I saw the warning below from
several files. Compared the tc-matchall.8 with bridge.8 and used .RI
instead of .R. It should have no effect on the man page rendering.
`R' is a string (producing the registered sign), not a macro.
Signed-off-by: Alexander Alemayhu <alexander@alemayhu.com>
Having some examples in the top level man page might make it a little bit easier
for new users to get started. Reused some words / sentences from the existing
man pages.
Suggested-by: 積丹尼 Dan Jacobson <jidanni@jidanni.org>
Signed-off-by: Alexander Alemayhu <alexander@alemayhu.com>
Add support for new afstats subcommand. This uses the new
IFLA_STATS_AF_SPEC attribute of RTM_GETSTATS messages to show
per-device, AF-specific stats. At the moment the kernel only supports
MPLS AF stats, so that is all that's implemented here.
The print_num function is exposed from ipaddress.c to be used for
printing the new stats so that the human-readable option, if set, can
be respected.
Example of use:
$ ./ip/ip -f mpls link afstats dev eth1
3: eth1
mpls:
RX: bytes packets errors dropped noroute
9016 98 0 0 0
TX: bytes packets errors dropped
7232 113 0 0
Signed-off-by: Robert Shearman <rshearma@brocade.com>
This patch adds support for a new xstats link subcommand which uses the
specified link type's new parse/print_ifla_xstats callbacks to display
extended statistics.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Lucas Bates <lucasb@mojatatu.com>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Extend ICMP code and type match to support masks.
Also add missing documentation to synopsis in manpage.
tc qdisc add dev eth0 ingress
tc filter add dev eth0 protocol ipv6 parent ffff: flower \
indev eth0 ip_proto icmpv6 type 128/240 code 0 action drop
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Unlike other PREFIXes documented in the usage for tc flower, which accept
both IPv4 and IPv6 prefixes, arp_sip and arp_tip only accepts IPv4
prefixes.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Add an example of packet sampling to the tc-matchall man page examples
section. The example uses the matchall classifier and the sample action to
create packet sampling on a port.
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
In addition to general information about the tc action, the man entry
contains common usage examples and information about the tlv fields packed
within each sampled packet.
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Descriptions of each route sub-command's arguments are enclosed in
.RS/.RE pairs. For 'replace' sub-command, '.RE' was incorrectly put
before the last argument ('expires').
Fixes: 3fbe7ca847 ("iproute2: ip-route.8.in: Add expires option for ip route")
Signed-off-by: Phil Sutter <phil@nwl.cc>
Add documentation about the extended statistics to the ifstat man page.
Add ifstat man age to the man8 Makefile
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
The man page contains two examples, which have different indentation. Fix
the indentation of the two examples to match.
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
This fixes two issues with the provided example:
- Add missing 'dev' keyword to second command.
- Use a real IPv4 address instead of a bogus hex value since that will
be rejected by get_addr_ipv4().
Fixes: dbfb17a67f ("man: tc-csum.8: Add an example")
Reported-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Phil Sutter <phil@nwl.cc>
Instead of "magic numbers" we can now specify each flag
by name. Prefix of "no" (e.g nofrag) unsets the flag,
otherwise it wil be set.
Example:
# add a flower filter that will drop fragmented packets
tc filter add dev ens4f0 protocol ip parent ffff: \
flower \
src_mac e4:1d:2d:fd:8b:01 \
dst_mac e4:1d:2d:fd:8b:02 \
indev ens4f0 \
ip_flags frag \
action drop
# add a flower filter that will drop non-fragmented packets
tc filter add dev ens4f0 protocol ip parent ffff: \
flower \
src_mac e4:1d:2d:fd:8b:01 \
dst_mac e4:1d:2d:fd:8b:02 \
indev ens4f0 \
ip_flags nofrag \
action drop
Fixes: 22a8f01989 ('tc: flower: support matching flags')
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Correct typo in example in ife man page.
Fixes: 06f9a59170 ("man: tc-ife.8: man page for ife action")
Cc: Lucas Bates <lucasb@mojatatu.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
This patch adds a new argument to the bridge fdb show command that allows
to filter by entry state.
Also update the man page to include all available show arguments.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Since 41aa17ff46 ("tc/cls_flower: Add dest UDP port to tunnel params")
tc flower supports setting the dest UDP port.
* Use "port_number" to be consistent with other man-page text
* Re-add "enc_dst_port" documentation to manpage which was
accidently removed by b2a1f740aa ("tc: flower: document that *_ip
parameters take a PREFIX as an argument.")
Cc: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
* The argument to src_mac and dst_mac may now take an optional mask
to limit the scope of matching.
* This address is is documented as a LLADDR in keeping with ip-link(8).
* The formats accepted match those already output when dumping flower
filters from the kernel.
Example of use of LLADDR with and without a mask:
tc qdisc add dev eth0 ingress
tc filter add dev eth0 protocol ip parent ffff: flower indev eth0 \
src_mac 52:54:01:00:00:00/ff:ff:00:00:00:01 action drop
tc filter add dev eth0 protocol ip parent ffff: flower indev eth0 \
src_mac 52:54:00:00:00:00/23 action drop
tc filter add dev eth0 protocol ip parent ffff: flower indev eth0 \
src_mac 52:54:00:00:00:00 action drop
Signed-off-by: Simon Horman <simon.horman@netronome.com>
* The argument to src_ip, dst_ip, enc_src_ip and enc_dst_ip take an
optional prefix length which is used to provide a mask to limit the scope
of matching.
* This is documented as a PREFIX in keeping with ip-route(8).
Example of uses of IPv4 and IPv6 prefixes
tc qdisc add dev eth0 ingress
tc filter add dev eth0 protocol ip parent ffff: flower \
indev eth0 dst_ip 192.168.1.1 action drop
tc filter add dev eth0 protocol ip parent ffff: flower \
indev eth0 src_ip 10.0.0.0/8 action drop
tc filter add dev eth0 protocol ipv6 parent ffff: flower \
indev eth0 src_ip 2001:DB8:1::/48 action drop
tc filter add dev eth0 protocol ipv6 parent ffff: flower \
indev eth0 dst_ip 2001:DB8::1 action drop
Signed-off-by: Simon Horman <simon.horman@netronome.com>
* The argument to src_mac and dst_mac may now take an optional mask
to limit the scope of matching.
* This address is is documented as a LLADDR in keeping with ip-link(8).
* The formats accepted match those already output when dumping flower
filters from the kernel.
Example of use of LLADDR with and without a mask:
tc qdisc add dev eth0 ingress
tc filter add dev eth0 protocol ip parent ffff: flower indev eth0 \
src_mac 52:54:01:00:00:00/ff:ff:00:00:00:01 action drop
tc filter add dev eth0 protocol ip parent ffff: flower indev eth0 \
src_mac 52:54:00:00:00:00/23 action drop
tc filter add dev eth0 protocol ip parent ffff: flower indev eth0 \
src_mac 52:54:00:00:00:00 action drop
Signed-off-by: Simon Horman <simon.horman@netronome.com>
* The argument to src_ip, dst_ip, enc_src_ip and enc_dst_ip take an
optional prefix length which is used to provide a mask to limit the scope
of matching.
* This is documented as a PREFIX in keeping with ip-route(8).
Example of uses of IPv4 and IPv6 prefixes
tc qdisc add dev eth0 ingress
tc filter add dev eth0 protocol ip parent ffff: flower \
indev eth0 dst_ip 192.168.1.1 action drop
tc filter add dev eth0 protocol ip parent ffff: flower \
indev eth0 src_ip 10.0.0.0/8 action drop
tc filter add dev eth0 protocol ipv6 parent ffff: flower \
indev eth0 src_ip 2001:DB8:1::/48 action drop
tc filter add dev eth0 protocol ipv6 parent ffff: flower \
indev eth0 dst_ip 2001:DB8::1 action drop
Signed-off-by: Simon Horman <simon.horman@netronome.com>
'ip vrf' follows the user semnatics established by 'ip netns'.
The 'ip vrf' subcommand supports 3 usages:
1. Run a command against a given vrf:
ip vrf exec NAME CMD
Uses the recently committed cgroup/sock BPF option. vrf directory
is added to cgroup2 mount. Individual vrfs are created under it. BPF
filter attached to vrf/NAME cgroup2 to set sk_bound_dev_if to the VRF
device index. From there the current process (ip's pid) is addded to
the cgroups.proc file and the given command is exected. In doing so
all AF_INET/AF_INET6 (ipv4/ipv6) sockets are automatically bound to
the VRF domain.
The association is inherited parent to child allowing the command to
be a shell from which other commands are run relative to the VRF.
2. Show the VRF a process is bound to:
ip vrf id
This command essentially looks at /proc/pid/cgroup for a "::/vrf/"
entry with the VRF name following.
3. Show process ids bound to a VRF
ip vrf pids NAME
This command dumps the file MNT/vrf/NAME/cgroup.procs since that file
shows the process ids in the particular vrf cgroup.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
To be installed with the other man pages.
Fixes: d57639a475 ("tc/act_tunnel: Introduce ip tunnel action")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Amir Vadai <amir@vadai.me>
Replace vlan_eth_type with vlan_ethtype.
Fixes: 745d917260 ("tc: flower: Introduce vlan support")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Enhance tunnel key action parameters by adding destination UDP port.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Enhance IP tunnel parameters by adding destination UDP port.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Adds support to configure BPF programs as nexthop actions via the LWT
framework.
Example:
ip route add 192.168.253.2/32 \
encap bpf out obj lwt_len_hist_kern.o section len_hist \
dev veth0
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Support matching on ICMP type and code.
Example usage:
tc qdisc add dev eth0 ingress
tc filter add dev eth0 protocol ip parent ffff: flower \
indev eth0 ip_proto icmp type 8 code 0 action drop
tc filter add dev eth0 protocol ipv6 parent ffff: flower \
indev eth0 ip_proto icmpv6 type 128 code 0 action drop
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Now that we made the BPF loader generic as a library, reuse it
for loading XDP programs as well. This basically adds a minimal
start of a facility for iproute2 to load XDP programs. There
currently only exists the xdp1_user.c sample code in the kernel
tree that sets up netlink directly and an iovisor/bcc front-end.
Since we have all the necessary infrastructure in place already
from tc side, we can just reuse its loader back-end and thus
facilitate migration and usability among the two for people
familiar with tc/bpf already. Sharing maps, performing tail calls,
etc works the same way as with tc. Naturally, once kernel
configuration API evolves, we will extend new features for XDP
here as well, resp. extend dumping of related netlink attributes.
Minimal example:
clang -target bpf -O2 -Wall -c prog.c -o prog.o
ip [-force] link set dev em1 xdp obj prog.o # attaching
ip [-d] link # dumping
ip link set dev em1 xdp off # detaching
For the dump, intention is that in the first line for each ip
link entry, we'll see "xdp" to indicate that this device has an
XDP program attached. Once we dump some more useful information
via netlink (digest, etc), idea is that 'ip -d link' will then
display additional relevant program information below the "link/
ether [...]" output line for such devices, for example.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
This is needed for some HWs to do proper macthing and steering.
Possible values are none, link, network, transport.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Add missing usage help for devlink dev eswitch subcommand.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Remove references to eth_type and ether_type (spelling error) in
the tc flower manpage.
Also correct formatting of boldface text with whitespace.
Cc: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
This action could be used before redirecting packets to a shared tunnel
device, or when redirecting packets arriving from a such a device.
The 'unset' action is optional. It is used to explicitly unset the
metadata created by the tunnel device during decap. If not used, the
metadata will be released automatically by the kernel.
The 'set' operation, will set the metadata with the specified values for
the encap.
For example, the following flower filter will forward all ICMP packets
destined to 11.11.11.2 through the shared vxlan device 'vxlan0'. Before
redirecting, a metadata for the vxlan tunnel is created using the
tunnel_key action and it's arguments:
$ tc filter add dev net0 protocol ip parent ffff: \
flower \
ip_proto 1 \
dst_ip 11.11.11.2 \
action tunnel_key set \
src_ip 11.11.0.1 \
dst_ip 11.11.0.2 \
id 11 \
action mirred egress redirect dev vxlan0
Signed-off-by: Amir Vadai <amir@vadai.me>
Introduce classifying by metadata extracted by the tunnel device.
Outer header fields - source/dest ip and tunnel id, are extracted from
the metadata when classifying.
For example, the following will add a filter on the ingress Qdisc of shared
vxlan device named 'vxlan0'. To forward packets with outer src ip
11.11.0.2, dst ip 11.11.0.1 and tunnel id 11. The packets will be
forwarded to tap device 'vnet0':
$ tc filter add dev vxlan0 protocol ip parent ffff: \
flower \
enc_src_ip 11.11.0.2 \
enc_dst_ip 11.11.0.1 \
enc_key_id 11 \
dst_ip 11.11.11.1 \
action mirred egress redirect dev vnet0
Signed-off-by: Amir Vadai <amir@vadai.me>
This is needed for some HWs to do proper macthing and steering.
Possible values are none, link, network, transport.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Add missing usage help for devlink dev eswitch subcommand.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Adjusting iproute2 utility to support new macvlan link type mode called
"source".
Example of commands that can be applied:
ip link add link eth0 name macvlan0 type macvlan mode source
ip link set link dev macvlan0 type macvlan macaddr add 00:11:11:11:11:11
ip link set link dev macvlan0 type macvlan macaddr del 00:11:11:11:11:11
ip link set link dev macvlan0 type macvlan macaddr flush
ip -details link show dev macvlan0
Based on previous work of Stefan Gula <steweg@gmail.com>
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Cc: steweg@gmail.com
v5:
- rebase and fix checkpatch
v4:
- add MACADDR_SET support
- skip FLAG_UNICAST / FLAG_UNICAST_ALL as this is not upstream
- fix man page
This makes use of the sctp_diag interface recently added to the kernel.
Joint work with Xin Long who provided the PoC implementation which I
merely polished up a bit.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Remove left over usage from removal of eth_type argument.
Fixes: 488b41d020 ('tc: flower no need to specify the ethertype')
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
So far, only the 'egress' direction was implemented.
Allow specifying 'ingress' as the direction packet appears on the target
interface.
For example, this takes incoming 802.1q frames on veth0 and redirects
them for input on dummy0:
# tc filter add dev veth0 parent ffff: pref 1 protocol 802.1q basic \
action mirred ingress redirect dev dummy0
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Recently a new per-port flag was added which controls the flooding of
unknown multicast, this patch adds support for controlling it via iproute2.
It also updates the man pages with information about the new flag.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Add support for controling hardware offload using (now standard)
skip_sw and skip_hw flags in cls_bpf.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Adjusting iproute2 utility to support new macvlan link type mode called
"source".
Example of commands that can be applied:
ip link add link eth0 name macvlan0 type macvlan mode source
ip link set link dev macvlan0 type macvlan macaddr add 00:11:11:11:11:11
ip link set link dev macvlan0 type macvlan macaddr del 00:11:11:11:11:11
ip link set link dev macvlan0 type macvlan macaddr flush
ip -details link show dev macvlan0
Based on previous work of Stefan Gula <steweg@gmail.com>
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Cc: steweg@gmail.com
Introduce a new API that exposes a list of vlans per VF (IFLA_VF_VLAN_LIST),
giving the ability for user-space application to specify it for the VF as
an option to support 802.1ad (VST QinQ).
We introduce struct vf_vlan_info, which extends struct vf_vlan and adds
an optional VF VLAN proto parameter.
Default VLAN-protocol is 802.1Q.
Add IFLA_VF_VLAN_LIST in addition to IFLA_VF_VLAN to keep backward
compatibility with older kernel versions.
Suitable ip link tool command examples:
- Set vf vlan protocol 802.1ad (S-TAG)
ip link set eth0 vf 1 vlan 100 proto 802.1ad
- Set vf vlan S-TAG and vlan C-TAG (VST QinQ)
ip link set eth0 vf 1 vlan 100 proto 802.1ad vlan 30 proto 802.1Q
- Set vf to VST (802.1Q) mode
ip link set eth0 vf 1 vlan 100 proto 802.1Q
- Or by omitting the new parameter (backward compatible)
ip link set eth0 vf 1 vlan 100
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
The 'vlan modify' action allows to replace an existing 802.1q tag
according to user provided settings.
It accepts same arguments as the 'vlan push' action.
For example, this replaces vid 6 with vid 5:
# tc filter add dev veth0 parent ffff: pref 1 protocol 802.1q \
basic match 'meta(vlan mask 0xfff eq 6)' \
action vlan modify id 5 continue
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Hi,
On Thu, Sep 08, 2016 at 11:59:55AM +0200, Michal Kubecek wrote:
> On Thu, Sep 01, 2016 at 09:04:54AM -0700, Stephen Hemminger wrote:
> > On Tue, 30 Aug 2016 17:32:52 -0700
> > Iskren Chernev <iskren@imo.im> wrote:
> >
> > > From 416f45b62f33017d19a9b14e7b0179807c993cbe Mon Sep 17 00:00:00 2001
> > > From: Iskren Chernev <iskren@imo.im>
> > > Date: Tue, 30 Aug 2016 17:08:54 -0700
> > > Subject: [PATCH bug-fix] iproute: fix documentation for ip rule scan order
> > >
> > > ---
> > > man/man8/ip-rule.8 | 2 +-
> > > 1 file changed, 1 insertion(+), 1 deletion(-)
> > >
> > > diff --git a/man/man8/ip-rule.8 b/man/man8/ip-rule.8
> > > index 1774ae3..3508d80 100644
> > > --- a/man/man8/ip-rule.8
> > > +++ b/man/man8/ip-rule.8
> > > @@ -93,7 +93,7 @@ Each policy routing rule consists of a
> > > .B selector
> > > and an
> > > .B action predicate.
> > > -The RPDB is scanned in order of decreasing priority. The selector
> > > +The RPDB is scanned in order of increasing priority. The selector
> > > of each rule is applied to {source address, destination address,
> > > incoming
> > > interface, tos, fwmark} and, if the selector matches the packet,
> > > the action is performed. The action predicate may return with success.
> > > --
> > > 2.4.5
> >
> > Applied
>
> I'm sorry I didn't notice before but this just reverts the change done
> by commit 4957250166 ("iproute2: clarification of various man8 pages").
> IMHO the problem is that both versions are equally confusing as the word
> "priority" can be understood in two different senses.
>
> How about more explicit formulation, e.g.
>
> ... in order of decreasing logical priority (i.e. increasing numeric
> values).
>
> Would that be better?
Looks like the real issue is missing definition of priority. What about
this:
use get_be64() in place of get_u64() when parsing input 'sci' parameter,
so that 'sci' can be entered using network byte order regardless the
endianness of target system; use ntohll() when printing out 'sci'. While
at it, improve documentation of 'sci' in ip-link.8.
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
remove hardcoded base 10 parsing of 'port' parameter, update man page
and fix usage() functions as well. Fix misleading line in man page that
theoretically allowed specifying 'port' keyword right after 'sci' keyword.
Provide documentation of 'address' parameter in man pages and in usage()
functions as well.
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
The current vlan push action supports only vid and protocol options.
Add priority option.
Example script that adds vlan push action with vid and priority:
tc filter add dev veth0 protocol ip parent ffff: \
flower \
indev veth0 \
action vlan push id 100 priority 5
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Classification according to vlan id and vlan priority.
Example script that adds vlan filter:
# add ingress qdisc
tc qdisc add dev ens4f0 ingress
# add a flower filter with vlan id and priority classification
tc filter add dev ens4f0 protocol 802.1Q parent ffff: \
flower \
indev ens4f0 \
vlan_ethtype ipv4 \
vlan_id 100 \
vlan_prio 3 \
action vlan pop
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
In addition to providing information about the mathcall filter and its
configurations, the man entry contains examples for creating port
mirorring entries.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
In this patch we introduce the ability to get UDP specific bearer
options such as remoteip, remoteport, localip and localport.
After some discussions on tipc-discussion on how to handle media
specific options we agreed to pass them after the media.
For media generic bearer options we already do:
$ tipc bearer get OPTION media MEDIA name|device NAME|DEVICE
For the UDP media specific bearer options we introduce in this path:
$ tipc bearer get media udp name NAME OPTION
such as
$ tipc bearer get media udp name NAME remoteip
This allows bash-completion to tab complete only appropriate options,
it makes more logical sense and it scales better. Even though it might
look a little different to the user.
In order to use the existing option parsing framework to do this we
add a flag (OPT_KEY) to the option parsing function.
If the UDP bearer has multiple remoteip addresses associated with it
(replicast) we handle the TIPC_NLA_UDP_MULTI_REMOTEIP flag and send
a TIPC_NL_UDP_GET_REMOTEIP query transparently to the user.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Introduce the ability to add remote IP addresses to an existing UDP
bearer. On the kernel side, adding a "remoteip" to an existing bearer
puts the bearer in "replicast" mode where TIPC multicast messages are
send out to each configured remoteip using unicast. This is required
for TIPC UDP bearers to work in environments where IP multicast is
disabled.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Implement kernel devlink e-switch interface. Currently we allow
to get and set the device e-switch mode.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roi Dayan <roid@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
This patch adds support for the stats argument to the bridge
vlan command which will display the per-vlan statistics and the device
each vlan belongs to with its flags. The supported command filtering
options are dev and vid. Also the man page is updated to explain the new
option.
The patch uses the new RTM_GETSTATS interface with a filter_mask to dump
all bridges and ports vlans. Later we can add support for using the
per-device dump and filter it in the kernel instead.
Example:
$ bridge -s vlan show
port vlan id
br0 1 Egress Untagged
RX: 2536 bytes 20 packets
TX: 2536 bytes 20 packets
101
RX: 43158 bytes 50 packets
TX: 43158 bytes 50 packets
eth1 1 Egress Untagged
RX: 2536 bytes 20 packets
TX: 2536 bytes 20 packets
100
RX: 0 bytes 0 packets
TX: 0 bytes 0 packets
101
RX: 43158 bytes 50 packets
TX: 43158 bytes 50 packets
102
RX: 16897 bytes 93 packets
TX: 0 bytes 0 packets
The format is the same as bridge vlan show but with stats, even though
under the hood the calls done to the kernel are different.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
This enables a user to remove an offline peer from the kernel data
structures. This could for example be useful when deliberately scaling
in peer nodes in a cloud environment.
This functionality was first merged in:
f9dec657e4 (Richard Alpe tipc: add peer remove functionality)
And later backed out (as the kernel counterpart was held up) in:
385caeb13b (Stephen Hemminger Revert "tipc: add peer remove functionality")
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Local ip is not required to identify a UDP bearer and shouldn't be
passed to bearer disable, set or get. In this patch we remove the
localip entry from the synopsis of these functions.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
This adds missing documentation of geneve type options:
- dstport
- external
- udpcsum
- udp6zerocsumtx
- udp6zerocsumrx
The bits for the last three was just copy and pasted from vxlan section.
Signed-off-by: Phil Sutter <phil@nwl.cc>
since kernel driver has valid default values for 'cipher' and 'icvlen',
there is no need for requiring users to specify both of them when a new
link is added. Also, prompt an error message and exit with appropriate
exit status in case of unsupported cipher suite.
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
fix output of "ip address help" and "ip link help". Update TYPE list in man
pages ip-address.8 and ip-link.8 as well.
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
- baseclass: major handle must match that of class's, Y defaults to 1
- flow map example: maps to 1-256, not 1-257
Signed-off-by: Michal Soltys <soltys@ziu.info>
Description copied from related kernel support commit message with a
little tailoring to fit.
While at it, fix font of non-terminal CONFFLAG-LIST in synopsis.
Signed-off-by: Phil Sutter <phil@nwl.cc>
This moves the warning to the beginning of the section about 'ip link
set' which makes it still stand out after adding more text to it's end.
Signed-off-by: Phil Sutter <phil@nwl.cc>
'ip link set' supports passing a type to set type-specific parameters.
Add this missing piece of information to the synopsis section.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Add option to suppress header line. When used the following line
is not shown:
"State Recv-Q Send-Q Local Address:Port Peer Address:Port"
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Add two NLA's that allow configuration of Infiniband node or port GUIDs
by referencing the IPoIB net device set over the physical function. The
format to be used is as follows:
ip link set dev ib0 vf 0 node_guid 00:02:c9:03:00:21:6e:70
ip link set dev ib0 vf 0 port_guid 00:02:c9:03:00:21:6e:78
Signed-off-by: Eli Cohen <eli@mellanox.com>
Add vrf keyword to 'ip route' commands. Allows:
1. Users can list routes by VRF name:
$ ip route show vrf NAME
VRF tables have all routes including local and broadcast routes.
The VRF keyword filters LOCAL and BROADCAST routes; to see all
routes the table option can be used. Or to see local routes only
for a VRF:
$ ip route show vrf NAME type local
2. Add or delete a route for a VRF:
$ ip route {add|delete} vrf NAME <route spec>
3. Do a route lookup for a VRF:
$ ip route get vrf NAME ADDRESS
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Add vrf keyword to 'ip neigh' commands. Allows listing neighbor
entries for all links associated with a given VRF.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Add vrf keyword to 'ip link' and 'ip addr' commands (common list code).
Allows:
1. Adding a link to a VRF
$ ip link set NAME vrf NAME
Removing a link from a VRF still uses 'ip link set NAME nomaster'
2. Showing links associated with a VRF:
$ ip link show vrf NAME
3. List addresses associated with links in a VRF
$ ip -br addr show vrf red
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
On devices that support TC flower offloads, these flags enable a filter to be
added only to HW or only to SW. skip_sw and skip_hw are mutually exclusive
flags. By default without any flags, the filter is added to both HW and SW,
but no error checks are done in case of failure to add to HW.
With skip-sw, failure to add to HW is treated as an error.
Here is a sample script that adds 2 filters, one with skip_sw and the other
with skip_hw flag.
# add ingress qdisc
tc qdisc add dev enp0s9 ingress
# enable hw tc offload.
ethtool -K enp0s9 hw-tc-offload on
# add a flower filter with skip-sw flag.
tc filter add dev enp0s9 protocol ip parent ffff: flower \
ip_proto 1 indev enp0s9 skip_sw \
action drop
# add a flower filter with skip-hw flag.
tc filter add dev enp0s9 protocol ip parent ffff: flower \
ip_proto 3 indev enp0s9 skip_hw \
action drop
Signed-off-by: Amir Vadai <amirva@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
I'll make a formal submission sans the header when the kernel patches
makes it in. This version is for someone who wants to play around with
the net-next kernel patches i sent
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Doc text shamelessly stolen from the introducing commit's message
(6c55c8c461 ['ip link set vf: Added "query_rss" command']).
Signed-off-by: Phil Sutter <phil@nwl.cc>
Not sure why this was limited to ip-link before. It is semantically
equal to the 'master' keyword, which is not restricted at all.
The man page and help text adjustments include the 'master' keyword as
well since that is also supported but wasn't documented before.
Cc: Vadim Kochan <vadim4j@gmail.com>
Signed-off-by: Phil Sutter <phil@nwl.cc>
This resolves what appears to be a typo.
Cc: Tom Herbert <tom@herbertland.com>
Reviewed-by: Dinan Gunawardena <dinan.gunawardena@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Extend ip-link to create MACsec devices
ip link add link <master> <macsec> type macsec [options]
Add `ip macsec` command to configure receive-side secure channels and
secure associations within a macsec netdevice.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Phil Sutter <phil@nwl.cc>
This patch drops the redundant description of some of ip's options in
ip-link.8's description of the 'show' subcommand, preserving the
description of -iec (but appending it to the list in ip.8 with minor
fixes).
Signed-off-by: Phil Sutter <phil@nwl.cc>
Follow-up for kernel commit 8eb3b99554b8 ("geneve: support setting
IPv6 flow label") to allow setting the label for the device config.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Follow-up for kernel commit e7f70af111f0 ("vxlan: support setting
IPv6 flow label") to allow setting the label for the device config.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This should be made generic and part of a common tc-actions man page.
Though leave it here for now to not confuse readers of the example which
uses it.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
As Jamal pointed out, there are two different approaches to bandwidth
measurement. Try to make this clear by separating them in synopsis and
also documenting the way to fine-tune avrate.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
As Jamal suggested, BRANCH is the wrong name, as these keywords go
beyond simple branch control - e.g. loops are possible, too. Therefore
rename the non-terminal to CONTROL instead which should be more
appropriate.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Recently a new temp router port mode was added and with it the dumped
information was extended similar to how mdb entries were done. This
patch adds support to dump the new information by using the "-s" switch.
Example:
$ bridge -d -s mdb show
dev br0 port eth1 grp ff02::1:ffbf:5716 temp 234.39
dev br0 port eth1 grp 239.0.0.2 temp 97.17
dev br0 port eth1 grp 239.0.0.3 temp 105.36
router ports on br0: eth1 0.00 permanent
router ports on br0: eth2 254.87 temp
It also updates the bridge man page.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Not sure how useful they are in practice, but as 'ip neigh' supports
setting them all, they deserve to be described as well.
While at it, also add a missing layer of indentation to the subordinate
nud state list.
Signed-off-by: Phil Sutter <phil@nwl.cc>
The documentation is wrong here: it is indeed possible to remove policy
rule 0 and recreate it afterwards. Therefore remove these statements.
Signed-off-by: Phil Sutter <phil@nwl.cc>
While the synopsis section contains 'ip route list', it is later
described as 'ip route show'. Make this consistent by replacing 'list'
with 'show' in synopsis.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Listing generic 'ip' options in subcommand man pages is redundant and
error-prone, as they won't be kept in sync anyway. Since many other man
pages don't list them either, drop references to them in the remaining
ones.
Signed-off-by: Phil Sutter <phil@nwl.cc>
The 'ADDR' part of 'local' and 'remote' parameters is not optional, but
may also consist of the word 'any'. While at it, add missing whitespace
and fix fonts.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Drop unnecessary curly braces around single action keywords, point out
that 'dev' parameter to 'ip token get' is optional and clarify that 'ip
token' defaults to 'list' action.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Clarify that 'ip rule' defaults to action 'list', that 'flush' and
'save' actions don't accept additional parameters, add missing 'not' and
'goto' keywords and finally fix fonts used in 'fwmark' and 'realms'
parameters.
Signed-off-by: Phil Sutter <phil@nwl.cc>
The first line contained a c'n'p error, incorrectly listing 'ip address'
syntax. Since PARAMS is used just once and there are not many other
parameters to 'ip ntable change', state them inline and in addition to
that clarify the possibility to pass multiple parameters at once.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Use brackets to show that 'ip netns' defaults to action 'list', drop
superfluous curly braces around 'set' action keyword.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Reflect that it is possible to pass multiple parameters at the same
time, also use the same trick the help text uses to emphasize vf
specific parameters.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Clarify that the optional '-' prefix of the 'tentative', 'deprecated'
and 'dadfailed' keywords has to be put right in front of them, no
whitespace is allowed in between.
In addition to that, clarify that it is valid to pass both 'valid_lft'
and 'preferred_lft' at the same time to 'ip address'.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Recently support was added to the kernel to be able to add more per-mdb
entry attributes via standard netlink attributes of type MDBA_MDB_EATTR_.
This patch adds support to iproute2 to parse and output these
attributes. The first exported attribute is the mdb "timer" value which
is shown only when the "-s" iproute2 arg is used.
Example:
$ bridge -s mdb show
dev br0 port eth1 grp 239.0.0.11 permanent 0.00
dev br0 port eth1 grp 239.0.0.10 temp 244.15
dev br0 port eth1 grp 239.0.0.1 temp 245.21
dev br0 port eth1 grp 239.0.0.5 temp 246.43
dev br0 port eth2 grp 239.0.0.5 temp 248.44
dev br0 port eth1 grp 239.0.0.2 temp 245.32
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Add IFLA_VF_TRUST message to trust the VF.
PF can accept some privileged operation from the trusted VF.
For example, ixgbe PF doesn't allow to enable VF promiscuous mode until
the VF is trusted because it may hurt performance.
To trust VF.
# ip link set dev eth0 vf 1 trust on
To untrust VF.
# ip link set dev eth0 vf 1 trust off
Signed-off-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
This patch is a follow up to the recently added
'static' fdb option.
It introduces a new option 'dynamic' which adds
dynamic fdb entries with NUD_REACHABLE.
$bridge fdb add 00:01:02:03:04:06 dev eth0 master dynamic
$bridge fdb show
00:01:02:03:04:06 dev eth0
This patch also documents all fdb types. Removes 'temp'
from usage message since it is now replaced by 'static'.
'temp' still works and is synonymous with static.
Signed-off-by: Wilson Kok <wkok@cumulusnetworks.com>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
This patch adds a -K / --kill option to ss that attempts to
forcibly close matching sockets using SOCK_DESTROY.
Because ss typically prints sockets instead of acting on them,
and because the kernel only supports forcibly closing some types
of sockets, the output of -K is as follows:
- If closing the socket succeeds, the socket is printed.
- If the kernel does not support forcibly closing this type of
socket (e.g., if it's a UDP socket, or a TIME_WAIT socket),
the socket is silently skipped.
- If an error occurs (e.g., permission denied), the error is
reported and ss exits.
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
grff wrapper returns warnings when parsing the ip-link.8.in file.
How to reproduce:
$ man --warnings ip-link > /dev/null
`R' is a string (producing the registered sign), not a macro.
[...]
Signed-off-by: Thomas Faivre <thomas.faivre@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Options 'group' and 'remote' cannot take 'any' as value but 'local' can.
Signed-off-by: Thomas Faivre <thomas.faivre@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
This enables a user to remove an offline peer from the kernel data
structures. This could for example be useful when deliberately scaling
in peer nodes in a cloud environment.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
This enables a user to remove an offline peer from the kernel data
structures. This could for example be useful when deliberately scaling
in peer nodes in a cloud environment.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Despite commit 45a82e5 ("iproute vxlan add support for fdb replace
command"), the 'fdb replace' command was not mentioned in bridge.8.
Signed-off-by: Phil Sutter <phil@nwl.cc>
