Before:
```
donatas-laptop# show bgp ipv4 unicast community-list testas
% testas is not a valid community-list name
donatas-laptop# con
donatas-laptop(config)# bgp community-list standard testas permit internet
donatas-laptop(config)# do show bgp ipv4 unicast community-list testas
donatas-laptop(config)#
```
`is not a valid community-list name` is a misleading warning message.
Doing the same for filter-list, access-list, prefix-list, route-map.
Signed-off-by: Donatas Abraitis <donatas@opensourcerouting.org>
Although VTY_GET_CONTEXT can return a failed value, it will
never happen in pbrd because of how context work. In
any event add some code to make coverity happy
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
ls_msg2edge calls ls_edge_del_all which will free the
edge variable. Ensure that FRR properly returns NULL.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
The call into pim_cmd_lookup_vrf may be NULL
and dereferencing it before ensuring that the
vrf pointer is non-NULL is a good way to crash.
A crash can be initiated in pim:
eva# show ip msdp vrf NOEXIST mesh-group
vtysh: error reading from pimd: Permission denied (13)Warning: closing connection to pimd because of an I/O error!
eva# 2022/08/15 11:47:38 [PHJDC-499N2][EC 100663314] STARVATION: task vtysh_rl_read (560b77f76de6) ran for 16777ms (cpu time 0ms)
eva#
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
When calling pim_upstream_add, the lookup for upstream
or the creation of the upstream cannot fail. As such
up is never NULL.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
in pim_ifchannel.c there exists several spots where
the ch->upstream is assumed to be NULL. This is not
possible.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
For now, only if the knob is enabled. Later this gonna be (most likely) removed
and routes with AS_SET / AS_CONFED_SET will be denied by default.
Signed-off-by: Donatas Abraitis <donatas@opensourcerouting.org>
Coverity spotted 3 places where `int ret = XXX` was
being used and FRR was immediately assigning a different
value.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
I am seeing the zebra_pw_install_retry timer thread crashing
on shutdown
The shutdown of the timer is only in an
if () {
...
} else if
Let's just always shut it down.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
When a neighbor goes down on an interface and that interface
has no more neighbors in a viable state where packets should
be being sent, then let's clear up the oi->obuf associated
with the interface the neighbor is on.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
ospf_write pulls an interface off the ospf->oi_write_q
then writes one packet and places it back on the queue,
keeping track of the first one sent. Then it will
stop sending packets even if we get back to the first
interface written too but before we have sent the full
pkt_count. I do not believe this makes a whole bunch
of sense and is very restrictive of how much data can
be sent especially if you have a limited number of peers
but large amounts of data. Why be so restrictive?
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
If we have conditional advertisement enabled, and conditionally withdrew
some prefixes, and then we do a 'clear bgp', those routes were getting
advertised again, and then withdrawn the next time the conditional
advertisement scanner executed.
When we go to advertise check the prefix against the conditional
advertisement status so we don't do that.
Signed-off-by: Quentin Young <qlyoung@nvidia.com>
The new outbound filter to apply conditional advertisement policy was
not working properly due to complications with update groups. The two
routemaps were properly copied into the update group peer filter but not
the conditional advertisement state.
Signed-off-by: Quentin Young <qlyoung@nvidia.com>
Signed-off-by: Mark Stapp <mstapp@nvidia.com>
After all needed interfaces ( for example: interface "a1", vrf "vrf1", and
"a1" is binded to "vrf1" ) are ready/created, then restart/start frr. zebra
at startup will call `netlink_interface()` to process all interfaces and notify
all clients, but its calling `get_iflink_speed()` maybe fails for unexpected
order of the coming interfaces: when processing "a1", "vrf1" maybe is unknown
at that time. `if_zebra_speed_update()` timer is introduced to deal with this
order problem.
Currently only ospfd and ospf6d deal with this speed change to recalculated
route cost. ospfd can deal with this change, but ospf6d will wrongly missed it.
Since both `ipv6 ospf6 cost COST` and `auto-cost reference-bandwidth COST` are
not set, cost of this ospf6 interface should be calculated with interface
speed, but it is wrongly kept to `10`, which is based on interface speed being
`0` for it missed speed change. Further, ECMP function becomes invalid after
restart frr, beacuse some ospf6 interfaces of one ECMP are wrongly with cost
`10`.
To avoid missing, recalculate cost for ospf6 interfaces based on potentially
changed speed.
Signed-off-by: anlan_cs <vic.lan@pica8.com>