Upon if_down, we don't reset the valid flag for dependents
and unset the INSTALLED flag.
So when its time for the NHG to be deleted (routes dereferenced),
zebra deletes it since refcnt goes to 0, but stale NHG remains in kernel.
Ticket :#4200788
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Signed-off-by: Rajasekar Raja <rajasekarr@nvidia.com>
When stopping and restarting BGP daemon part of the configuration
remains. It should be cleared.
Particulary those are address-family parametes, like: distance,
ead-es-frag, disable-ead-evi-rx, disable-ead-evi-tx.
Signed-off-by: Yaroslav Kholod <y.kholod@vyos.io>
The rpki current state was ignored when calling for the 'show bgp ipvX
detail' command. Handle the support for this, with json support too.
> "rpkiValidationState" : "valid",
> "rpkiValidationState" : "invalid",
> "rpkiValidationState" : "not used",
> "rpkiValidationState" : "not found",
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Signed-off-by: Dmytro Shytyi <dmytro.shytyi@6wind.com>
When reloading the following configuration:
```
segment-routing
srv6
formats
format usid-f3216
wide-local-id-block explicit start 100
exit
!
format uncompressed-f4024
exit
!
exit
!
exit
!
exit
```
frr-reload.py does not properly enter the `formats` context. Because of this,
it fails with an unknown command error when applying new or updating format
configuration.
Signed-off-by: Jonathan Voss <jvoss@onvox.net>
`srv6_static_route` is a pure staticd topotest. It does not have any
dependency on bgpd and sharpd.
Let's fix the pytestmark to include only staticd.
Signed-off-by: Carmine Scarpitta <cscarpit@cisco.com>
This test was not actually failing when the results didn't match. Fail
now. Also fix the tests that are now found to be failing incorrectly
(wrong expected result).
Signed-off-by: Christian Hopps <chopps@labn.net>
If we do `no neighbor PG enforce-first-as`, it wasn't working because the flag
was inherited incorrectly for the members of the peer-group.
Fixes: 322462920e ("bgpd: Enable enforce-first-as by default")
Closes: https://github.com/FRRouting/frr/issues/17702
Signed-off-by: Donatas Abraitis <donatas@opensourcerouting.org>
Compile error with `--disable-ripd`:
```
mgmtd/mgmt_be_adapter.c:86:5: error: "HAVE_RIPD" is not defined, evaluates to 0 [-Werror=undef]
86 | #if HAVE_RIPD
| ^~~~~~~~~
```
I have searched the code, there is only three places need to be fixed.
Signed-off-by: anlan_cs <anlan_cs@126.com>
The documentation should provide the valid range of SRv6 locator
node-len parameter, rather than the default value.
Signed-off-by: Carmine Scarpitta <cscarpit@cisco.com>
The documentation should provide the valid range of SRv6 locator
block-len parameter, rather than the default value.
Signed-off-by: Carmine Scarpitta <cscarpit@cisco.com>
Align the order of the SRv6 locator parameters with the actual implementation:
```
"prefix X:X::X:X/M$prefix [block-len (16-64)$block_bit_len] \
[node-len (16-64)$node_bit_len] [func-bits (0-64)$func_bit_len]"
```
Signed-off-by: Carmine Scarpitta <cscarpit@cisco.com>
For JSON output we don't need newline to be printed.
Before:
```
"lastUpdate":{"epoch":1734490463,"string":"Wed Dec 18 04:54:23 2024\n"
```
After:
```
"lastUpdate":{"epoch":1734678560,"string":"Fri Dec 20 09:09:20 2024"
```
Signed-off-by: Donatas Abraitis <donatas@opensourcerouting.org>
newline is not expected to be printed in JSON outputs, e.g.:
```
"lastUpdate":{"epoch":1734490463,"string":"Wed Dec 18 04:54:23 2024\n"
```
Signed-off-by: Donatas Abraitis <donatas@opensourcerouting.org>
When deactivating babel no router babel and later re-enabling
it router babel the previous configuration is still in place.
Steps to reproduce:
- Enable babel
- Configure babel
- Disable babel with "no router babel"
- Verify config
Expected correct behavior: No config present
Signed-off-by: Yaroslav Kholod <y.kholod@vyos.io>
