other network namespaces are parsed because bridge interface can be
bridged with vxlan interfaces with a link in the default vrf that hosts
l2vpn.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
With vrf-lite mechanisms, it is possible to create layer 3 vnis by
creating a bridge interface in default vr, by creating a vxlan interface
that is attached to that bridge interface, then by moving the vxlan
interface to the wished vrf.
With vrf-netns mechanism, it is slightly different since bridged
interfaces can not be separated in different network namespaces. To make
it work, the setup consists in :
- creating a vxlan interface on default vrf.
- move the vxlan interface to the wished vrf ( with an other netns)
- create a bridge interface in the wished vrf
- attach the vxlan interface to that bridged interface
from that point, if BGP is enabled to advertise vnis in default vrf,
then vxlan interfaces are discovered appropriately in other vrfs,
provided that the link interface still resides in the vrf where l2vpn is
advertised.
to import ipv4 entries from a separate vrf, into the l2vpn, the
configuration of vni in the dedicated vrf + the advertisement of ipv4
entries in bgp vrf will import the entries in the bgp l2vpn.
the modification consists in parsing the vxlan interfaces in all network
namespaces, where the link resides in the same network namespace as the
bgp core instance where bgp l2vpn is enabled.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
If you issue this command:
`git config blame.ignoreRevsFile .git-blame-ignore-revs`
Then when you do a git blame XXX, git will ignore the whitespace
changes we made in mass.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
In the case of P2P links it is possible to use IP unnumbered which
yields a strong dependency to the interface data for nexthop
resolution in the SPF calculations. While the SPF code strives to
be as independent of non-LSA data as possible there is no way
around here: one has to resolve the nexthop for such a special case
using the interface data.
For this purpose a new flag 'spf_root_node' is introduced to signal
that interface data can be used for P2P links. For now this flag is
always 'true' since the SPF currently always uses the calculating
node as the root node. This will change with the introduction of
TI-LFA where other nodes can be root nodes.
Signed-off-by: GalaxyGorilla <sascha@netdef.org>
in OSPF interface data is used for the nexthop resolution
during the SPF algorithm, see RFC2328 16.1.1. However, for
certain technologies like TI-LFA it is desirable to be able
to calculate SPFs for arbitrary root nodes, not just the
calculating node. Since interface data is not available for
other nodes it is necessary to remove this dependency and
make its usage optional, depending on the intent of
changing the RIB with the generated tree (or not).
To signal that a SPF run is used without the intent to
change the RIB an additional flag `spf_dry_run` is
introduced to the ospf_area struct. This flag is currently
only used within the pure SPF code but will be extended
to the SPF postprocessing later on.
Signed-off-by: GalaxyGorilla <sascha@netdef.org>
The RFC states:
The BGP Identifier is a 4-octet, unsigned, non-zero integer that
should be unique within an AS. The value of the BGP Identifier
for a BGP speaker is determined on startup and is the same for
every local interface and every BGP peer.
We were going slightly beyond this and ensuring that the address
was a specific range of addresses which is no longer relevant.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
* Replaced alias for bgp shutdown command with separate regular command
to prevent internal CLI errors.
Signed-off-by: David Schweizer <dschweizer@opensourcerouting.org>
While a configuration transaction can't be rejected once it reaches
the APPLY phase, we should allow NB callbacks to generate error
or warning messages when a configuration change is being applied.
That should be useful, for example, to return warnings back to
the user informing that the applied configuration has some kind of
inconsistency or is missing something in order to be effectively
activated. The infrastructure for this was already present, but the
northbound layer was ignoring all errors/warnings generated during
the apply/abort phases instead of returning them to the user. This
commit changes that.
In the gRPC plugin, extend the Commit() RPC adding a new
"error_message" field to the response type. This is necessary to
allow errors/warnings to be returned even when the commit operation
succeeds (since grpc::Status::OK doesn't support error messages
like the other status codes).
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
1. Created a structure "isis master".
2. All the changes are related to handle ISIS with different vrf.
3. A new variable added in structure "isis" to store the vrf name.
4. The display commands for isis is changed to support different VRFs.
Signed-off-by: Kaushik <kaushik@niralnetworks.com>
Yang files for bgpd to use northbound APIs
Co-authored-by: Santosh P K <sapk@vmware.com>
Co-authored-by: vishaldhingra <vdhingra@vmware.com>
Signed-off-by: vishaldhingra <vdhingra@vmware.com>
Experimental patch to allow us to discuss if we should
allow bfdd to work when v6 is turned off in the kernel.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
* Peers are now automatically restarted by the reconnect timer instead
of a ManualStart event after lifting the administrative shutdown.
* Question of when to log what remains.
* Compiles and works as intended now.
Signed-off-by: David Schweizer <dschweizer@opensourcerouting.org>
Just non-functional changes, cosmetics, removal of eye
cancer. The intention here is to make the SPF code more
approachable.
Signed-off-by: GalaxyGorilla <sascha@netdef.org>
* Fixed integration in FSM and packet handling.
* Added CLI "show" output, incl. JSON.
* For review and testing only.
Signed-off-by: David Schweizer <dschweizer@opensourcerouting.org>
Use `args->errmsg` instead of just `zlog_info` for registering the error
so the users don't need to check their log files.
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
* Changes allow administratively shutting down all peers of a BGP
instance.
* New CLI commands "[no] bgp shutdown" in vty shell.
* For review and testing only.
Signed-off-by: David Schweizer <dschweizer@opensourcerouting.org>
This would be handy for situations when a notification was sent, but it's
absolutely not clear who triggered that.
Just in case dumping all attributes under the debug mode would help finding
the _bad_ attribute.
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
The support bundle feature(tm) asks for some data
from zebra in the form of a command that has
never existed in FRR. Looks like some
cruft snuck in remove.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
We can make the Linux kernel send an ARP/NDP request by adding
a neighbour with the 'NUD_INCOMPLETE' state and the 'NTF_USE' flag.
This commit adds new dataplane operation as well as new zapi message
to allow other daemons send ARP/NDP requests.
Signed-off-by: Jakub Urbańczyk <xthaid@gmail.com>
Add a new test to cover the new features for multi hop BFD peers:
- Test that we correctly receive TTL from protocol integration.
- Check minimum TTL usage and 'show' command.
- Check for passive mode.
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
The commit `bfdd: simplify and remove duplicated code` fixed a problem
that was causing the protocol configuration to override the user
configuration.
In this test case: the peer was configured to be disabled (default is
`shutdown`) and the test was expecting it to get activated (`no shutdown`)
when the protocol converged. I changed the peer default state to
`no shutdown`, however another way to get the same effect is to
configure the protocol to use a profile or don't configure a peer at all
(and use the defaults).
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
