The bestpath multipath-relax setting was added to the output of
"show ip bgp neighbor json" several months ago but this is not
the correct place to display that information and this fix removes
it from there. The multipath-relax setting was also added
to the output of "show ip bgp sum json" which is fine.
Signed-off-by: Don Slice <dslice@cumulusnetworks.com>
Adds ability to specify that peers should be administratively shutdown
when first configured.
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
Remove the ability to attempt to configure a couple of options on
directly connected neighbors that don't make sense for them, as well as
the soft error handling code.
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
If we have configured neighbor 1.1.1.1 for an afi/safi but they have not
activated that afi/safi with us then display "NoNeg" in the state column
of the summary output. This is to make troubleshooting afi/safi
easier.
Signed-off-by: Daniel Walton <dwalton@cumulusnetworks.com>
The bgpTimerUp value was incorrectly named, add
a correct name bgpTimerUpMsec and add some
code to allow for deprecation.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
For some reason bgp is calculating the peer uptime
in miliseconds incorrectly. Additionally we have
the peer_uptime function call that should be doing this!
But since we've choosen different names for the json output
we cannot fix it at this point.
uptime contains the number of seconds of uptime here. Just
multiply by 1k and display that( as peer_uptime does )
Fixes: #1585
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Was using 0 as a sentinel value, so user couldn't configure 0 as the
value of the coalesce timer.
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
BGP VRF can be created/deleted either via config or via l3vni add/del.
We need to handle various sequences.
1. If user config is presented, an l3vni del should not delete the vrf instance
2. do not write bgp config in show running for auto created vrf
2. If l3vni present, disallow the cli for deleting bgp vrf instance
3. If l3vni is added and vrf config is present set the flags properly
4. if bgp vrf is configured unset the AUTO flag
Ticket: CM-18630
Review: CCR-6906
Testing: Manual
Signed-off-by: Mitesh Kanjariya <mitesh@cumulusnetworks.com>
Since coalesce time is now heuristically adjusted based on peer count,
we need to separate out specific configuration by the user from the
current value. Behavior established is to not adjust if the user has a
value set.
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
bgpd supports setting a write-quanta that serves as a hint on how many
packets to write per I/O cycle. Now that input is buffered, it makes
sense to add the equivalent parameter for how many packets are processed
per cycle. This is *not* how many packets are read off the wire per I/O
cycle; rather it is how many packets are processed from the input buffer
in a given cycle after having been read off the wire and sanitized.
Since these values must be used from multiple threads, they have also
been made atomic.
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
* Move and modify all network input related code to bgp_io.c
* Add a real input buffer to `struct peer`
* Move connection initialization to its own thread.c task instead of
piggybacking off of bgp_read()
* Tons of little fixups
Primary changes are in bgp_packet.[ch], bgp_io.[ch], bgp_fsm.[ch].
Changes made elsewhere are almost exclusively refactoring peer->ibuf to
peer->curr since peer->ibuf is now the true FIFO packet input buffer
while peer->curr represents the packet currently being processed by the
main pthread.
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
* Remove t_write
* Remove t_keepalive
These have been replaced by pthreads and are no longer needed. Since
some code looks at these values to determine if the threads are
scheduled, also add a new bitfield to store the same information.
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
Building a communities json object every time is
both expensive and memory wasteful. Modify
code to only build the json object when needed.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Fixes a bug whereby all peer-groups would be shown even when a
particular peer-group was specified for display.
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
Problem reported that we weren't adjusting the keepalive timer
correctly when we negotiated a lower hold time learned from a
peer. While working on this, found we didn't do inheritance
correctly at all. This fix solves the first problem and also
ensures that the timers are configured correctly based on this
priority order - peer defined > peer-group defined > global config.
This fix also displays the timers as "configured" regardless of
which of the three locations above is used.
Ticket: CM-18408
Signed-off-by: Don Slice <dslice@cumulusnetworks.com>
Reviewed-by: CCR-6807
Testing-performed: Manual testing successful, fix tested by
submitter, bgp-smoke completed successfully
When retrieving information about neighbors or summary in json
add some information about what bestPath particulars we have for
this bgp session.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Signed-off-by: Daniel Walton <dwalton@cumulusnetworks.com>
VARIABLE tokens must be all uppercase, this allows us to support WORD
tokens that begin with an uppercase letter. The "Null0" keyword is an
example of where this is needed.
The only VARIABLE we had that wasn't already all uppercase was
ASN:nn_or_IP-address:nn
1) Add hash names to all hash_create calls
2) Fix community_hash, ecommunity_hash and lcommunity_hash key
creation
3) Fix output of community and lcommunity iterators( why would
we want to see the memory location of the backet? ).
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Some of this was so egregiously stupid, I couldn't look at it without
gouging my eyes out...
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
afi_header_vty_out() is easily replaced with vty_frame(), which means we
can drop a whole batch of "int *write" args as well as the entirety of
bgp_config_write_family_header().
=> AFI/SAFI config writing is now a lot simpler.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
The bgp clear help string was misordered.
New output:
robot.cumulusnetworks.com# clear bgp
(1-4294967295) Clear peers with the AS number
* Clear all peers
A.B.C.D BGP neighbor address to clear
WORD BGP neighbor on interface to clear
X:X::X:X BGP IPv6 neighbor to clear
external Clear all external peers
ipv4 Address Family
ipv6 Address Family
peer-group Clear all members of peer-group
prefix Clear bestpath and re-advertise
view BGP view
vrf BGP VRF
Fixes: #1005
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
When the MAC changes for a local neighbor, ensure that the neighbor data
structure as well as the link between the neighbor and MAC data structures
is updated correctly.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Mitesh Kanjariya <mitesh@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ticket: CM-17565
Reviewed By: CCR-6605
Testing Done: Manual, evpn-smoke
1. Added support to create mac filters
2. Enabled route-map commands for EVPN address family
3. Provision to add mac filters under match clause in route-maps
Ticket: CM-16349
Review: CCR-6190
Unit-test: Manual (logs attached to ticket)
Signed-off-by: Mitesh Kanjariya <mitesh@cumulusnetworks.com>
SAFI values have been a major source of confusion over the last few
years. That's because each SAFI needs to be represented in two different
ways:
* IANA's value used to send/receive packets over the network;
* Internal value used for array indexing.
In the second case, defining reserved values makes no sense because we
don't want to index SAFIs that simply don't exist. The sole purpose of
the internal SAFI values is to remove the gaps we have among the IANA
values, which would represent wasted memory in C arrays. With that said,
remove these reserved SAFIs to avoid further confusion in the future.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
This reverts commit c14777c6bf.
clang 5 is not widely available enough for people to indent with. This
is particularly problematic when rebasing/adjusting branches.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Signed-off-by: Daniel Walton <dwalton@cumulusnetworks.com>
This allows frr-reload.py (or anything else that scripts via vtysh)
to know if the vtysh command worked or hit an error.
Most of the attributes in 'struct attr_extra' allow for
the more interesting cases of using bgp. The extra
overhead of managing it will induce errors as we add
more attributes and the extra memory overhead is
negligible on anything but full bgp feeds.
Additionally this greatly simplifies the code for
the handling of data.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
bgpd: Fix missing label set
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Implement configuration options for EVPN. The configuration options include
VNI configuration with RD and Import and Export Route Targets. Also, display
the EVPN configuration.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Signed-off-by: Daniel Walton <dwalton@cumulusnetworks.com>
Implement the command 'advertise-all-vni' under the EVPN address-family
in order to allow the local system to learn about local VNIs (and MACs
and Neighbors corresponding to those VNIs) and exchange with other EVPN
speakers.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Dinesh Dutt <ddutt@cumulusnetworks.com>
Signed-off-by: Daniel Walton <dwalton@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Restoring some code that was unintentionally removed when we were
migrating to Quentin's parser.
* Pass ->text to functions that now do full string matching
* Remove cases for l2vpn and evpn where they cannot occur
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
log.c provides functionality for associating a constant (typically a
protocol constant) with a string and finding the string given the
constant. However this is highly delicate code that is extremely prone
to stack overflows and off-by-one's due to requiring the developer to
always remember to update the array size constant and to do so correctly
which, as shown by example, is never a good idea.b
The original goal of this code was to try to implement lookups in O(1)
time without a linear search through the message array. Since this code
is used 99% of the time for debugs, it's worth the 5-6 additional cmp's
worst case if it means we avoid explitable bugs due to oversights...
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
Signed-off-by: Daniel Walton <dwalton@cumulusnetworks.com>
- All ipv4 labeled-unicast routes are now installed in the ipv4 unicast
table. This allows us to do things like take routes from an ipv4
unicast peer, allocate a label for them and TX them to a ipv4
labeled-unicast peer. We can do the opposite where we take routes from
a labeled-unicast peer, remove the label and advertise them to an ipv4
unicast peer.
- Multipath over a labeled route and non-labeled route is not allowed.
- You cannot activate a peer for both 'ipv4 unicast' and 'ipv4
labeled-unicast'
- The 'tag' variable was overloaded for zebra's route tag feature as
well as the mpls label. I added a 'mpls_label_t mpls' variable to
avoid this. This is much cleaner but resulted in touching a lot of
code.
* Ranges for some MED were 2^32 - 2 instead of 2^32 - 1
* Use correct printf specifiers for unsigned values
* Some drive-by CLI collapsing and simplification
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
(This was intended as further demonstration of the DEFPY code, but it
might as well go into the tree.)
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Revert "ospf6d: fix decimal area ID cli"
commit a27cb3cfe9
Revert "bgpd: add back unicast option to 'address-family vpnv(4&6)' Issue #459"
commit 399598bf6b
Revert "Fix the memory leak"
commit d8d58e9839
Revert "zebra: 'no ip route 4.1.1.19 255.255.255.255 99' is ambiguous"
commit 83f3561935
Revert "ospf6d: Allow unconfig of unknown lsa's"
commit 5b0747d71d
Revert "Fix the "Dead assignment" of clang SA."
commit 3a6570a1f1
Revert "snapcraft: Improve README.usage.md based on feedback received"
commit 2a3a819a9c
Revert "zebra: stop deregistering static nexthops unless removing the static"
commit 1dac3a9619
All of these changes do not apply on stable/3.0 due to either CLI
changes or another fix already being present.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Sometimes, like once every 400 iterations, when you restart
Quagga, extended-nexthop has been turned off for interface
based config( for 5549 ).
Examining the code, there is only 1 real path to setting
the PEER_FLAG_CAPABILITITY_ENHE and that is through
peer_conf_interface_get. Modify this code path
to always set the PEER_FLAG_CAPABILITY_ENHE if it is
not already set.
In addition, fix a possible pointer dereference.
Ticket: CM-12929
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
When we configure authentication. Allow the 'show bgp neighbor'
commands( and their ilk ) to indicate that the peer has
authentication enabled.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Signed-off-by: Daniel Walton <dwalton@cumulusnetworks.com>
Reviewed-by: Don Slice <dslice@cumulusnetworks.com>
If you did:
neighbor swp1 interface
neighbor swp1 interface remote-as external
we would not set the remote-as. You could however still do
neighbor swp1 remote-as external
Sometimes, like once every 400 iterations, when you restart
Quagga, extended-nexthop has been turned off for interface
based config( for 5549 ).
Examining the code, there is only 1 real path to setting
the PEER_FLAG_CAPABILITITY_ENHE and that is through
peer_conf_interface_get. Modify this code path
to always set the PEER_FLAG_CAPABILITY_ENHE if it is
not already set.
In addition, fix a possible pointer dereference.
Ticket: CM-12929
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
The FSF's address changed, and we had a mixture of comment styles for
the GPL file header. (The style with * at the beginning won out with
580 to 141 in existing files.)
Note: I've intentionally left intact other "variations" of the copyright
header, e.g. whether it says "Zebra", "Quagga", "FRR", or nothing.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
This wasn't quite correct in the previous patch, leading to peer-groups
& interface peers breaking in autocompletion.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Problem uncovered with crash when entering the command "show ip bgp
vrf vrf1001 0.0.0.0". The crash was caused by a mistake incrementing
the index value in the vrf/view case. Manual testing completed and
failing test case now passes successfully.
Ticket: CM-16223
Signed-off-by: Don Slice <dslice@cumulusnetworks.com>
Reviewed By: Donald Sharp <sharpd@cumulusnetworks.com>
This fixes two crashes:
1) When we enter a 'neighbor shutdown..' command for a peer
group or interface based peer we were not properly looking
up the peer.
2) When we we enter 'no neighbor shutdown..' command for
a peer group or interface based peer we were not properly
lookup up the peer.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
The 'show ip bgp neighbors swp31s0' command was not
working properly. This fixes that issue.
This command still has issues that need to be investigated
but for the moment this gets the command working in the
form that is needed. More rework can come.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Modify the 'show ... bgp ... summary' command when you are
looking at a afi( with no safi specified ) to only display
output for those safi's that have been configured.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
The use of VTY_DECLVAR_CONTEXT(bgp, bgp) here is wrong as we are not
inside the "router bgp" configuration node. This was making the clear
commands always fail with a "Current configuration object was deleted
by another process" error, which doesn't make any sense.
Also, the bgp_clear() function will already check for us if the given
peer-group or neighbor exists or not, there's no need to duplicate this
logic here.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Remove the UNDEFINED_NODE as that it's implementation breaks
our ability in BGP to figure out where we are by allowing
default: in the switch statement.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Implement support for activating the labeled-unicast address family in
BGP and relevant configuration for this address family.
Signed-off-by: Don Slice <dslice@cumulusnetworks.com>
These have copies in vtysh that do the node-switch locally and are
listed in extract.pl's ignore list. The ignore list however is
redundant since DEFUN_NOSH does the same thing...
ldpd is a bit hacky, but Renato is reworking this anyway.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
When starting up bgp and zebra now, you can specify
-e <number> or --ecmp <number>
and that number will be used as the maximum ecmp
that can be used.
The <number specified must be >= 1 and <= MULTIPATH_NUM
that Quagga is compiled with.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
The introduction of AFI_L2VPN prefix makes usage of AFI_ETHER deprecated
and is of no usage currently. The former replaces the latter one.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Added the possibility to enter in evpn address-family in bgp node, by
using 'address-family l2vpn evpn' command.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
To handle BGP NLRI EVPN messages, bgp is modified to handle AFI_L2VPN
and SAFI_EVPN values.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Introduction of EVPN address-family node that is reachable under
BGP node, like follow: address-family evpn. Under that node, only
some commands are available for configuring a neighbor or setting
some basic settings like attribute unchanged behaviour. Currently,
no vty command is available for setting NLRI entries for EVPN.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
dn_flag was tested inside of a 'use_json' block
further down in the function. Move initialization
of the value to outside of the !use_json if statement
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
This reverts commit 713de0685f.
During Discussions with Lou, it was decided that his code
changes would handle this part, and my code changes would
fix up vtysh and bgp to be in sync again.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
The behavior of some show commands was switched from
showing the unicast data to all safi data. This
is a change in behavior and needs to be put
back for 2.0
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
extract.pl.in requires the lines that are ignored
to be consisten with what is in the *.c file
that we are ignoring from, else we get ambiguous
commands.
This allows vtysh to enter address-family sub mode
in bgp again.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ticket: CM-14136
Reviewed By: CCR-5585
Testing Done: bgpmin
The JSON output of 'bgp neighbor show' lacked the decoded strings for
the last notification error code/subcode. Decoding these strings outside
quagga is painful, and then needs to match with any updates to the codes
from RFCs/drafts. Further, all apps that look to understanding this need
to then add their own decoders for these strings.
Just add the decoded strings to the JSON output as well. JSON key name
for this is 'lastNotificationReason'.
Signed-off-by: Dinesh Dutt <ddutt@cumulusnetworks.com>
A common misconfiguration that was silently accepted but wouldn't work
was including the prefix length on the update-source; i.e. 10.1.1.1/32.
This commit rejects this config and notifies the user.
Ticket: CM-13485
Signed-off-by: Don Slice <dslice@cumulusnetworks.com.
Reviewed-by: Donald Sharp
Somewhere in the past we switched from
using the auto-generated redistribute statements
to a non-generated version. This caused us to
loose new protocols to redistribute as they are
added. Put it back.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
This fix addresses these things:
1) Clean up documentation as requested
2) Fix a wrong search for "exact-match"
3) Fix possible crash.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Harmony is restored to the world as bgp and vtysh
can now, again, stay in sync with each other.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
(to match surrounding code)
"git diff -w" should be almost empty.
Copyright edited to say FRR, this is not GNU Zebra :)
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Because the vpn configuration command was duplicate, there was an
ambiguity to raise. This is a fix that permits configuring vpnv4 or
vpnv6 address-families on bgp.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
1) Make [<view|vrf> WORD] consistent
2) Fix inconsistent help string
3) Fix the show .. vrf all command
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Create bgp_vty_find_and_parse_afi_safi_vrf that
will parse the
`show [ip] bgp [<view|vrf> WORD] [<ipv4|ipv6> [<unicast|multicast|vpn|encap>]]'
part of a command and to return the correct spot we are in the command.
Cleanup 'dampening parameters' part of this command.
Consolidate the creation of the bgp data structure to be a bit cleaner.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
The bgp_parse_safi function is never called remove it.
Especially as that later commits will properly handle
what this function was trying to do.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
The original commit for large communities broke
'show ip bgp' and 'show bgp ipv4 unicast' and
their ilk. This commit fixes this as well
as some vtysh parse errors identified.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
BGP Large Communities are a novel way to signal information between
networks. An example of a Large Community is: "2914:65400:38016". Large
BGP Communities are composed of three 4-byte integers, separated by a
colon. This is easy to remember and accommodates advanced routing
policies in relation to 4-Byte ASNs.
This feature was developed by:
Keyur Patel <keyur@arrcus.com> (Arrcus, Inc.),
Job Snijders <job@ntt.net> (NTT Communications),
David Lamparter <equinox@opensourcerouting.org>
and Donald Sharp <sharpd@cumulusnetworks.com>
Signed-off-by: Job Snijders <job@ntt.net>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Use KEEP_OLD_VPN_COMMANDS define to brace some vty commands used by bgp
to configure or show vpnvx contexts using old method, that is to say
using vty keyword vpnv4 or vpnv6 command.
In addition to this, the commit adds two new commands under route-map
with new format:
[no] set ipv4|ipv6 vpn nexthop <IPv4 Address> | <IPv6 Address>
It also add following command in old format:
[no] set vpnv6 nexthop <IPv6 Address>
Note that the commit does not take into account the availability of old
commands that are not available in new format.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com
Conflicts (CLI vs. atol()):
- bgpd/bgp_vty.c
- ospfd/ospf_vty.c
- zebra/zebra_vty.c
NB: pull req #65 (LabNConsulting/working/2.0/afi-safi-vty/c) was
excluded from this merge.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Unfortunately, the CLI changes need to be redone on master since the CLI
has massively changed there.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Added defines and parse utility functions
Fix vty code that treated vpn&encap as AFIs
and some other related vty printing/handline issues
Note: Includes branch specific changes (due to new parser)
Signed-off-by: Lou Berger <lberger@labn.net>
On ARM platforms specifying a local-as greater than
2 billion causes issues due to atoi usage.
Ticket: CM-14019
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Preserve forwarding state bit can be set in OPEN message with the use of
new vty commands
bgp graceful-restart preserve-fw-state
no bgp graceful-restart preserve-fw-state
This must be set before activating the connection to a peer, since it is
for forging graceful restart capability of OPEN messages.
Signed-off-by: Julien Courtat <julien.courtat@6wind.com>
All of the autogenerated macros in lib/route_types.pl are now called
FRR_* instead of QUAGGA_*.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
The first time through calling 'show ip bgp summary'
we were always calculating the variable hostname field
size incorrectly.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
VTY_DECLVAR_CONTEXT already contains a NULL check, vty warning message
and return statement. These are not needed.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
These now generate warnings which will break the build with -Werror.
Note this may have enabled commands that should be disabled, or the
other way around...
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Additionally:
* Add [ip] to a couple bgp show commands
* Quick refactor of a couple ISIS commands
* Quick refactor of a couple OSPF6 commands
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
* show ip bgp vpnv4 all <A.B.C.D|A.B.C.D/M> [json]
* show...vpnv4 <all|rd ...> summary...
* Fix placement of AF+SAFI specifiers for BGP clear commands
* Add more [ip]'s for bgp commands
* clean up some doc strings
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
Signed-off-by: Daniel Walton <dwalton@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ticket: CM-13511
connectionsEstablished, etc are no longer under the addressFamilyInfo
keyword, they are now at the top level
Signed-off-by: Daniel Walton <dwalton@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Now that we display hostnames in 'show ip bgp summary' it is really easy
to have the first column be greater than 16 characters which causes a
line wrap. The line wrap makes the output difficult to read.
Before
======
superm-redxp-05# show ip bgp summ
BGP router identifier 6.0.0.11, local AS number 65001 vrf-id 0
BGP table version 56
RIB entries 19, using 2280 bytes of memory
Peers 2, using 41 KiB of memory
Peer groups 1, using 64 bytes of memory
Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd
leaf-11-really-long-name(swp1)
4 65101 307 322 0 0 0 00:14:15 10
leaf-12(swp2) 4 65101 105 121 0 0 0 00:14:14 Idle (Admin)
Total number of neighbors 2
superm-redxp-05#
After
=====
superm-redxp-05# show ip bgp summ
BGP router identifier 6.0.0.11, local AS number 65001 vrf-id 0
BGP table version 10
RIB entries 19, using 2280 bytes of memory
Peers 2, using 41 KiB of memory
Peer groups 1, using 64 bytes of memory
Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd
leaf-11-really-long-name(swp1) 4 65101 11 12 0 0 0 00:00:08 10
swp2 4 0 0 0 0 0 0 never Idle (Admin)
Total number of neighbors 2
superm-redxp-05#
superm-redxp-05#
Ticket: CM-13053
Reviewed By: dslice@cumulusnetworks.com
'neighbor x.x.x.x weight' was implemented as a per-peer knob instead of
a per-peer per-afi-safi option. This makes it configurable per-peer
per-afi-safi so that we can do things like soft clear that afi/safi when
weight is modified.
If a command is put into the VIEW_NODE, it is going into the
ENABLE_NODE as well. This is especially true for show commands.
As such if a command is in both consolidate it down to VIEW_NODE.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
The RESTRICTED_NODE command is not used, introduces code
complexity and provides no additional levels of security.
The only way to get into RESTRICTED_NODE is to add, under
vty configuration the command 'anonymous restricted', and
then telnet to a daemon, provide a password, then type
'enable' and fail to enter the password three times.
Then the user can enter a very limited set of commands to
monitor bgp and only bgp behavior.
This commit removes both the RESTRICTED_NODE usage as well
as the lib/* usage of the code
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Signed-off-by: Daniel Walton <dwalton@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Don Slice <dslice@cumulusnetworks.com>
Reviewed-by: Sam Tannous <stannous@cumulusnetworks.com>
Ticket:
These commands were ported forward from these
commits:
f9b6c39 bgpd: Add back old forms of 'show <afi> <safi>' for compatibility
bf1ae6c bgpd: drop machineparse / random "show" improvements
651b402 bgpd: encap show commands
35c3686 bgpd: VPNv6 show commands
135ca15 bgpd: cleanup vty bgp_node_afi/safi utils
This is the first drop of those commits. The files have
changed too much and the diffs to extensive to try to do it
in one piece. Break it up into smaller code chunks.
Original Code:
Signed-off-by: Lou Berger <lberger@labn.net>
Forward Port:
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
This is a rather large mechanical commit that splits up the memory types
defined in lib/memtypes.c and distributes them into *_memory.[ch] files
in the individual daemons.
The zebra change is slightly annoying because there is no nice place to
put the #include "zebra_memory.h" statement.
bgpd, ospf6d, isisd and some tests were reusing MTYPEs defined in the
library for its own use. This is bad practice and would break when the
memtype are made static.
Acked-by: Vincent JARDIN <vincent.jardin@6wind.com>
Acked-by: Donald Sharp <sharpd@cumulusnetworks.com>
[CF: rebased for cmaster-next]
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Signed-off-by: Christian Franke <chris@opensourcerouting.org>
Move over to the new allocation counting added in the previous commit.
(This commit is mostly mechanical.)
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Acked-by: Vincent JARDIN <vincent.jardin@6wind.com>
Found several leaks in bgp_show_peer and bgp_show_peer_afi where
json objects are created and then not attached to the parent, causing
them to be leaked. If not attaching them, freeing the created objects.
Manual testing performed successfully. Fix tested succesfully by the
submitter and bgp-smoke completed with same failures as base.
Ticket: CM-12846
Signed-off-by: Don Slice
Reviewed-by: CCR-5181
There is support to configure graceful restart timer. This is the
time to wait to delete stale routes before a BGP open message is
received.
bgp graceful-restart restart-time <1-3600>
no bgp graceful-restart [<1-255>]
* bgpd/bgp_vty.c
* Define command strings for above CLI
* bgpd/bgpd.c
* bgp_config_write(): Output graceful restart-time configuration
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Tested-by: NetDEF CI System <cisystem@netdef.org>
* Solaris doesn't have u_int64_t, so use uint64_t instead. C99-style
fixed-width integers should always be preferred to improve portability;
* 's_addr' is a macro on Solaris, so we can't use it as a variable name.
Rename the 's_addr' variable to 'addr' in the
bgp_peer_conf_if_to_su_update_v4() function.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
lib/zebra.h has FILTER_X #define's. These do not belong there.
Put them in lib/filter.h where they belong.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
(cherry picked from commit 0490729cc033a3483fc6b0ed45085ee249cac779)
Logic for determining the router-id was spread out over bgp_zebra.c and
bgp_vty.c. Move to bgpd/bgpd.c and have these two call more properly
encapsulated functions.
Significant work by Christian Franke <chris@opensourcerouting.org>.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Found that original fix for CM-10113 had a significant flaw, that
by deriving the bgp instance from the vty->index, if a clear ip bgp
command was entered from a vty index other then bgp, a crash occurred.
This fix passes the bgp->name to the clear functions so the correct
instance can be derived. Tested manually in both the CM-10113 case
as well as the problem discovered while testing CM-11480.
Ticket: CM-10113
Signed-off-by: Don Slice
Reviewed-by:
Some bgp commands end with doing a bgp_clear_vty, which invalidly
made the assumption that the clear should always be done for the default
instance. This fix derives the correct instance from the vty-index if
one is supplied, and uses the default instance if it is not.
Ticket: CM-10113
Signed-off-by: Don Slice
Reviewed-by: Donald Sharp
To make BGP configuration as simple as possible, assume the capability
extended-nexthop to be default for interface neighbors. Also allow the
ability to specify remote-as on the same line as neighbor interface to
make BGP unnumbered configuration a single line.
One corner case. This is the first feature for which the default for a
member is different from the default for a peer-group. Since advertising
the capability is only done for interface neighbors, the capability is
not set for the peer-group, but is automatically set for interface
neighbors that belong to that peer-group. So, if you want to disable the
advertisement of this capability for an interface neighbor, you must
do it per each interface neighbor.
The patch is more complicated than it needs to be due to the handling
of quagga reload and appropriate updates to the show running output.
Ticket: CM-11830
Reviewed By: CCR-4958
Testing Done: Usual coterie, including manual
(cherry picked from commit 347914a0a7)
When there is one BGP router instance, `no router bgp` may be used to
deconfigure it without specifying its ASN
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
ospfd: OSPF should accept "router-id IFNAME"
Added commands in BGP and OSPF where user can specify interface for router-id.
Ticket: CM-5040
Reviewed By: CCR-4908
Testing Done: Manual
"neighbor <interface> disable-connected-check" should not be allowed by the parser
Made changes to not allow hops greater than 1 and disable-connected check for neighbor <interface>
Ticket: CM-5536 CM-5537
Reviewed By: CCR-4865
Testing Done: Manual
Ticket: CM-11344
Reviewed By: dwalton, dsharp
Testing Done: built and tested amd64 debs
This patch adds the peerID JSON attribute for routes for show ip bgp json.
It also corrects the bgpTimerLastWrite in show ip bgp neigh json as well
as adds bgpInUpdateElapsedTimeMsecs, lastErrorCodeSubcode, and connectRetryTimer.
These are needed for the bgp4 mib implementation (rfc 4273) from the json
output of vtysh commands.
VPNv6 changes picked from upstream needed fixes and updates due to some
fundamental changes implemented by Cumulus (BGP update-groups, RFC 5549
and nexthop setting etc.) which aren't present upstream.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Updates: 945c8fe, 8ecd326, bb86c60, 93b73df, f4c8985
Ticket: CM-11350
Reviewed By: dsharp
Testing Done: built amd64 images and tested output of both json and non-json
Upstream patch was applied in wrong section of code so JSON
output contained plain text. The upstream patch was
commit baa376fc1 (cherry picked from ef757700d0f)
This patch moves the text output to the correct if clause
and also adds a new JSON line for the same data.
Signed-off-by: Sam Tannous <stannous@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Avoids a dynamic allocation which is usually freed immediate afterwards.
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
There wasn't much missing for VPNv6 to begin with; just a few bits of
de- & encoding and a few lists to be updated.
Signed-off-by: Lou Berger <lberger@labn.net>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
[Editorial note: Signed-off-by may imply an authorship claim, but need not]
Edited-by: Paul Jakma <paul.jakma@hpe.com> / <paul@jakma.org>
(cherry picked from commit 9da04bca0e994ec92b9242159bf27d89c6743354)
Conflicts:
bgpd/bgp_attr.c
bgpd/bgp_mplsvpn.c
bgpd/bgpd.c
Useful when the BGP neighbors are over tunnels that have large
differences in geographic distances and RTTs. Especially useful
for DMVPN setups to allow preferring closes hub.
The parameter is added as new alias command as otherwise it seems
the command parser is not able to match it properly (it seems
merging is done for the various 'set metric' route-map objects in
different routing engines). For same reason also they are listed
as three separate options: optional +/- seems not possibly easily.
Related research papers:
http://www.pps.univ-paris-diderot.fr/~jch/research/delay-based.pdfhttp://arxiv.org/pdf/1309.0632.pdf
Paper on similar extension to Babel:
http://www.pps.univ-paris-diderot.fr/~jch/research/rapport-jonglez-2013.pdf
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
(cherry picked from commit ef757700d0fd51dc0b46df9d3631208919f9b779)
On higher warning levels, compilers expect %p printf arguments to be
void *. Since format string / argument warnings can be useful
otherwise, let's get rid of this noise by sprinkling casts to void *
over printf calls.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Negative value in output of ecommunities (and as numbers)
seems odd :-). This patch fixes it. And add minor formating
modification, better for big as numbers.
Signed-off-by: Milan Kocian <milon@wq.cz>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
(cherry picked from commit cb4fc59c8a0f9df81109d38acbeaab5627e361f5)
Conflicts:
bgpd/bgp_vty.c
Fix lots of warnings. Some const and type-pun breaks strict-aliasing
warnings left but much reduced.
* bgp_advertise.h: (struct bgp_advertise_fifo) is functionally identical to
(struct fifo), so just use that. Makes it clearer the beginning of
(struct bgp_advertise) is compatible with with (struct fifo), which seems
to be enough for gcc.
Add a BGP_ADV_FIFO_HEAD macro to contain the right cast to try shut up
type-punning breaks strict aliasing warnings.
* bgp_packet.c: Use BGP_ADV_FIFO_HEAD.
(bgp_route_refresh_receive) fix an interesting logic error in
(!ok || (ret != BLAH)) where ret is only well-defined if ok.
* bgp_vty.c: Peer commands should use bgp_vty_return to set their return.
* jhash.{c,h}: Can take const on * args without adding issues & fix warnings.
* libospf.h: LSA sequence numbers use the unsigned range of values, and
constants need to be set to unsigned, or it causes warnings in ospf6d.
* md5.h: signedness of caddr_t is implementation specific, change to an
explicit (uint_8 *), fix sign/unsigned comparison warnings.
* vty.c: (vty_log_fixed) const on level is well-intentioned, but not going
to fly given iov_base.
* workqueue.c: ALL_LIST_ELEMENTS_RO tests for null pointer, which is always
true for address of static variable. Correct but pointless warning in
this case, but use a 2nd pointer to shut it up.
* ospf6_route.h: Add a comment about the use of (struct prefix) to stuff 2
different 32 bit IDs into in (struct ospf6_route), and the resulting
type-pun strict-alias breakage warnings this causes. Need to use 2
different fields to fix that warning?
general:
* remove unused variables, other than a few cases where they serve a
sufficiently useful documentary purpose (e.g. for code that needs
fixing), or they're required dummies. In those cases, try mark them as
unused.
* Remove dead code that can't be reached.
* Quite a few 'no ...' forms of vty commands take arguments, but do not
check the argument matches the command being negated. E.g., should
'distance X <prefix>' succeed if previously 'distance Y <prefix>' was set?
Or should it be required that the distance match the previously configured
distance for the prefix?
Ultimately, probably better to be strict about this. However, changing
from slack to strict might expose problems in command aliases and tools.
* Fix uninitialised use of variables.
* Fix sign/unsigned comparison warnings by making signedness of types consistent.
* Mark functions as static where their use is restricted to the same compilation
unit.
* Add required headers
* Move constants defined in headers into code.
* remove dead, unused functions that have no debug purpose.
(cherry picked from commit 7aa9dcef80b2ce50ecaa77653d87c8b84e009c49)
Conflicts:
bgpd/bgp_advertise.h
bgpd/bgp_mplsvpn.c
bgpd/bgp_nexthop.c
bgpd/bgp_packet.c
bgpd/bgp_route.c
bgpd/bgp_routemap.c
bgpd/bgp_vty.c
lib/command.c
lib/if.c
lib/jhash.c
lib/workqueue.c
ospf6d/ospf6_lsa.c
ospf6d/ospf6_neighbor.h
ospf6d/ospf6_spf.c
ospf6d/ospf6_top.c
ospfd/ospf_api.c
zebra/router-id.c
zebra/rt_netlink.c
zebra/rt_netlink.h
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Don Slice <dslice@cumulusnetworks.com>
Reviewed-by: Daniel Walton <dwalton@cumulusnetworks.com>
Signed-off-by: Daniel Walton <dwalton@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ticket: CM-11007
bgp_show_neighbor() was allocating a json_neigh struct and using that
for every single peer...so the resulting json was a munge of state from
all peers
We need to allocate a new json_neigh for each neighbor.
Signed-off-by: Daniel Walton <dwalton@cumulusnetworks.com>
Reviewed-by: vivek@cumulusnetworks.com
Ticket: CM-10694
To be backwards compatible we should silently accept the "exact" keyword
here
Instead of turning on IPv6 RA on every interface as soon as it has an IPv6
address, only enable it upon configuration of BGP neighbor. When the BGP
neighbor is deleted, signal that RAs can be turned off.
To support this, introduce new message interaction between BGP and Zebra.
Also, take appropriate actions in BGP upon interface add/del since the
unnumbered neighbor could exist prior to interface creation etc.
Only unnumbered IPv6 neighbors require RA, the /30 or /31 based neighbors
don't. However, to keep the interaction simple and not have to deal with
too many dynamic conditions (e.g., address deletes or neighbor change to/from
'v6only'), RAs on the interface are triggered upon any unnumbered neighbor
configuration.
BGP-triggered RAs will cause RAs to be initiated on the interface; however,
if BGP asks that RAs be stopped (upon delete of unnumbered neighbor), RAs
will continue to be exchanged if the operator has explicitly enabled.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ticket: CM-10640
Reviewed By: CCR-4589
Testing Done: Various manual and automated (refer to defect)
Ticket: CM-10644
Reviewed By:
Testing Done:
The JSON outputs of a bunch of BGP commands were broken due to the
addition of VRF support. This fixes them all. Also replaces the use
of "-" in some of the JSON variable names with camel case names.
Signed-off-by: Daniel Walton <dwalton@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ticket: CM-10002
superm-redxp-05# conf t
superm-redxp-05(config)# route-map FOO permit 10
superm-redxp-05(config-route-map)# set community ?
AA:NN Community number in AA:NN format (where AA and NN are <0-65535>) or local-AS|no-advertise|no-export|internet or additive
none No community attribute
superm-redxp-05(config-route-map)# set community 2:2
superm-redxp-05(config-route-map)# set community 2:70000
% Malformed communities attribute
superm-redxp-05(config-route-map)# set community 70000:2
% Malformed communities attribute
superm-redxp-05(config-route-map)#
Key BGP 'show' commands have been expanded to support 'vrf all':
show ip bgp vrf all summary
show ip bgp vrf all neighbors
show ip bgp vrf all nexthop
show ip bgp vrf all update-group
show ip bgp vrf all
show bgp vrf all summary
show bgp vrf all update-group
show bgp vrf all
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Don Slice <dslice@cumulusnetworks.com>
Ticket: CM-10402
Reviewed By: CCR-4466
Testing Done: Manual
When creating a 'struct peer' add in the ability to set the peer group
associated with that peer.
Ticket: CM-10184
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Daniel Walton <dwalton@cumulusnetworks.com>
Fix and enhance the entire hierarchy of clear commands in BGP to work
for VRFs.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Ticket: CM-9945
Reviewed By: CCR-4360
Testing Done: Manual (brief)
Updates to routemaps and delete of the routemap were not working properly
for VRFs. This was because while routemaps are global, the routemap update
processing timer and the processing were at the per-instance level. This
approach was unable to handle processing for multiple instances as the
routemap has no tracking of which instances are still pending processing.
This lead to the processing happening correctly only for the first instance
- which could be the default instance or some other instance. It could also
result in reference to freed memory for an instance.
The fix done is to make the update/delete processing also global and not per
instance. This means that the route-map delay timer will be global and a global
thread will handle the change (or delete) for all instances instead of spawning
a separate thread for each instance. To support this, a global BGP command
"bgp route-map delay-timer <value>" has been implemented. The existing command
per-instance is not deleted but will update the global timer.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ticket: CM-6970, CM-9918
Reviewed By: CCR-4320
Testing Done: Manual, bgpsmoke
Ensure commands dealing with update-groups and peer-groups support VRFs.
Also implement a new command "show bgp vrfs" to show summary information of
all configured VRFs. Some additional code cleanup in this area.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Ticket: CM-9247
Reviewed By: CCR-4267
Testing Done: Manual
'show bgp ipv4 uni summ' is counting each prefix sent
to each neighbor. At scale this is an expensive
operation.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Daniel Walton <dwalton@cumulusnetworks.com>
Various changes and fixes related to VRF registration, deletion,
BGP exit etc.
- Define instance type
- Ensure proper handling upon instance create, delete and
VRF add/delete from zebra
- Cleanup upon bgp_exit()
- Ensure messages are not sent to zebra for unknown VRFs
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ticket: CM-9128, CM-7203
Reviewed By: CCR-4098
Testing Done: Manual
The work-quanta that a user can specify is ~4billion. If a user
specifies such a large value this translates into processing 4billion
outgoing packets before moving onto the next interface. This makes
no sense. Reduce the value of allowed work quanta's to be between
1 and 10000.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Don Slice <dslice@cumulusnetworks.com>
Reviewed-by: Daniel Walton <dwalton@cumulusnetworks.com>
Reviewed-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Signed-off-by: Daniel Walton <dwalton@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Don Slice <dslice@cumulusnetworks.com>
Ticket: CM-8788
Modify the various maxpath commands to use MULTIPATH_NUM
as the upper limit of allowed max paths in BGP. There
is no point in allowing a number of maximum paths greater
than what Quagga is compiled for.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
BGP uses a second #define that is equal to MULTIPATH_NUM. There
is no point in having a different #define. Just consolidate.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
configuration
Signed-off-by: Daniel Walton <dwalton@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Dinesh Dutt <ddutt@cumulusnetworks.com>
Ticket: CM-8321
This allows the user to configure the peer-group as an option for the
"neighbor swpX interface" command.
{code}
!
router bgp 100
neighbor FOO peer-group
neighbor FOO remote-as external
neighbor swp1 interface
neighbor swp2 interface v6only
neighbor swp3 interface peer-group FOO
neighbor swp4 interface v6only peer-group FOO
!
address-family ipv4 unicast
neighbor FOO activate
neighbor swp1 activate
neighbor swp2 activate
exit-address-family
!
{code}
Note that if the user configures
{code}
neighbor swp5 interface
neighbor swp5 peer-group FOO
{code}
We will display that as "neighbor swp5 interface peer-group FOO". It
did not seem worth tracking that the peer-group was entered via two
lines instead of one.
During CR for nexthop upstream it was noticed that usage
of prefix2str was not consistent. This fixes this problem
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
The json keyword was being read incorrectly.
Basically some commands read a variable # of arguments
and in ospf the command values were being placed into
argc and argv. With a variable # of arguments their
existed a possibility that less arguments would be read
from the cli than were being tested for in the command function
handler. This caused core dumps in some situations.
All code to read to decide to use the json keyword has
been centralized through a function and all code
converted to use it, irrelevant if it exhibited the bug
Ticket: CM-8278
Reviewed by: CCR-3830
Testing: OSPF no longer crashes and all other test suites still run
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
BGP is currently displaying the in-use router-id in the config. This is
conditional on a CONFIG flag, however, that flag is set even when there
is no configured router-id and the router-id learnt from Zebra is in-use.
The CONFIG flag for router-id is redundant since there is a separate
variable for the configured value, so use that and deprecate the CONFIG
flag. This also makes BGP behave like OSPF.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Daniel Walton <dwalton@cumulusnetworks.com>
Ticket: CM-8077, CM-8220
Reviewed By: CCR-3793
Testing Done: Manual verification (in 2.5-br)
Note: Imported from 2.5-br patch bgpd-fix-router-id-config-display.patch
The code has tests to see if the MULTIPATH_NUM == 0 and to
treat it like the user has entered 'Maximum PATHS'.
This 0 is treated as 64 internally. Remove this dependency
and setup MULTIPATH_NUM to 64 when --enable-multipath=0 from
the configure cli.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Daniel Walton <dwalton@cumulusnetworks.com>
will be deprecated in the future
Signed-off-by: Daniel Walton <dwalton@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Ticket: CM-8144
Signed-off-by: Daniel Walton <dwalton@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ticket: CM-8122
per draft-ietf-idr-ix-bgp-route-server-09:
2.3.2.2.2. BGP ADD-PATH Approach
The [I-D.ietf-idr-add-paths] Internet draft proposes a different
approach to multiple path propagation, by allowing a BGP speaker to
forward multiple paths for the same prefix on a single BGP session.
As [RFC4271] specifies that a BGP listener must implement an implicit
withdraw when it receives an UPDATE message for a prefix which
already exists in its Adj-RIB-In, this approach requires explicit
support for the feature both on the route server and on its clients.
If the ADD-PATH capability is negotiated bidirectionally between the
route server and a route server client, and the route server client
propagates multiple paths for the same prefix to the route server,
then this could potentially cause the propagation of inactive,
invalid or suboptimal paths to the route server, thereby causing loss
of reachability to other route server clients. For this reason, ADD-
PATH implementations on a route server should enforce send-only mode
with the route server clients, which would result in negotiating
receive-only mode from the client to the route server.
This allows us to delete all of the following code:
- All XXXX_rsclient() functions
- peer->rib
- BGP_TABLE_MAIN and BGP_TABLE_RSCLIENT
- RMAP_IMPORT and RMAP_EXPORT
Signed-off-by: Daniel Walton <dwalton@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Vivek Venkataraman <vivek@cumulusnetworks.com
Ticket: CM-8014
This implements addpath TX with the first feature to use it
being "neighbor x.x.x.x addpath-tx-all-paths".
One change to show output is 'show ip bgp x.x.x.x'. If no addpath-tx
features are configured for any peers then everything looks the same
as it is today in that "Advertised to" is at the top and refers to
which peers the bestpath was advertise to.
root@superm-redxp-05[quagga-stash5]# vtysh -c 'show ip bgp 1.1.1.1'
BGP routing table entry for 1.1.1.1/32
Paths: (6 available, best #6, table Default-IP-Routing-Table)
Advertised to non peer-group peers:
r1(10.0.0.1) r2(10.0.0.2) r3(10.0.0.3) r4(10.0.0.4) r5(10.0.0.5) r6(10.0.0.6) r8(10.0.0.8)
Local, (Received from a RR-client)
12.12.12.12 (metric 20) from r2(10.0.0.2) (10.0.0.2)
Origin IGP, metric 0, localpref 100, valid, internal
AddPath ID: RX 0, TX 8
Last update: Fri Oct 30 18:26:44 2015
[snip]
but once you enable an addpath feature we must display "Advertised to" on a path-by-path basis:
superm-redxp-05# show ip bgp 1.1.1.1/32
BGP routing table entry for 1.1.1.1/32
Paths: (6 available, best #6, table Default-IP-Routing-Table)
Local, (Received from a RR-client)
12.12.12.12 (metric 20) from r2(10.0.0.2) (10.0.0.2)
Origin IGP, metric 0, localpref 100, valid, internal
AddPath ID: RX 0, TX 8
Advertised to: r8(10.0.0.8)
Last update: Fri Oct 30 18:26:44 2015
Local, (Received from a RR-client)
34.34.34.34 (metric 20) from r3(10.0.0.3) (10.0.0.3)
Origin IGP, metric 0, localpref 100, valid, internal
AddPath ID: RX 0, TX 7
Advertised to: r8(10.0.0.8)
Last update: Fri Oct 30 18:26:39 2015
Local, (Received from a RR-client)
56.56.56.56 (metric 20) from r6(10.0.0.6) (10.0.0.6)
Origin IGP, metric 0, localpref 100, valid, internal
AddPath ID: RX 0, TX 6
Advertised to: r8(10.0.0.8)
Last update: Fri Oct 30 18:26:39 2015
Local, (Received from a RR-client)
56.56.56.56 (metric 20) from r5(10.0.0.5) (10.0.0.5)
Origin IGP, metric 0, localpref 100, valid, internal
AddPath ID: RX 0, TX 5
Advertised to: r8(10.0.0.8)
Last update: Fri Oct 30 18:26:39 2015
Local, (Received from a RR-client)
34.34.34.34 (metric 20) from r4(10.0.0.4) (10.0.0.4)
Origin IGP, metric 0, localpref 100, valid, internal
AddPath ID: RX 0, TX 4
Advertised to: r8(10.0.0.8)
Last update: Fri Oct 30 18:26:39 2015
Local, (Received from a RR-client)
12.12.12.12 (metric 20) from r1(10.0.0.1) (10.0.0.1)
Origin IGP, metric 0, localpref 100, valid, internal, best
AddPath ID: RX 0, TX 3
Advertised to: r1(10.0.0.1) r2(10.0.0.2) r3(10.0.0.3) r4(10.0.0.4) r5(10.0.0.5) r6(10.0.0.6) r8(10.0.0.8)
Last update: Fri Oct 30 18:26:34 2015
superm-redxp-05#
When configuring listen ranges for allowing dynamic BGP neighbors,
ensure that there are no duplicate or overlapping ones. This is
necessary because at the time of handling an incoming connection,
the first range that matches the source of the connection (and hence,
its peer-group parameters) will be used.
Signed-off-by: Vivek Venkataraman <vivek@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Atul Patel <atul@cumulusnetworks.com>
Ticket: CM-5153
Reviewed By: CCR-3714
Testing Done: Manual verification
very easy to blackhole routes.
Signed-off-by: Daniel Walton <dwalton@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ticket: CM-6649
bgp is using both bm->master and master pointers interchangebly
for thread manipulation. Since they are the same thing consolidate
to one pointer.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ticket: CM-6680
Reviewed-by: CCR-3486
Testing: See bug
In these situations:
(A) user enters under bgp more 'maximum-paths' than zebra is compiled with
warn the user that there is a problem
(B) Zebra receives more maximum paths than what it can handle log the fact
that this happened
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ticket: CM-7439
Reviewed By: Donald Sharp
Testing Done:
If a session was reset due to a NOTIFICATION the "show ip bgp
neighbor" output would not display details on what the
notification actually was. This patch changes that. Example:
superm-redxp-05# show ip bgp neighbors 20.1.2.2
BGP neighbor is 20.1.2.2, remote AS 21, local AS 10, external link
[snip]
Last reset 01:05:07, due to NOTIFICATION sent (OPEN Message Error/Bad Peer AS)
This patch adds a hostname capability. The node's hostname and
domainname are exchanged in the new capability and used in show command
outputs based on a knob enabled by the user. The hostname and domainname
can be a maximum of 64 chars long, each.
Signed-off-by: Dinesh G Dutt <ddutt@cumulusnetworks.com>
Reviewed-by: Daniel Walton <dwalton@cumulusnetworks.com>
Reviewed-by: Vivek Venkataraman <vivek@cumulusnetworks.com>
Ticket: CM-5660
Reviewed By: CCR-2563
Testing Done:
Ticket: CM-7012
Reviwed by: CCR-3451
Testing: See bug
When you specify a neighbor <interface> <something>
and don't specify a remote-as the neighbor relationship
will still come up with ipv6 unnumbered if you have
RA configured on the interface.
Ticket: CM-7177
Reviewed-by: CCR-3396
Testing: See bug
This code change does several small things:
(A) Fix a couple detected memory leaks
(B) Fix all malloc operations to use the correct XMALLOC operation in bgpd and parts of lib
(C) Adds a few new memory types to make it easier to detect issues
Ticket: CM-6789
Reviewed By: CCR-3263
Testing Done: Manual Testing and smoke tests
Whenever some sort of output is encountered, added a json version with
proper logic as well.
Ticket: CM-6048
Reviewed-By: CCR-3251
Tested: See bug
When a redistribute metric is changed, the new metric
was not being used. Modify the code to look for existing
redistributed routes and fix their metric.
BGP: Determine peer's IP address if interface has /30, /31
Allow interface-based session config for IPv4 numbered links
if the link address is either /30 or /31. This is not RFC5549,
but can be deployed now, and independent of whether the peer
supports RFC5549 or not.
Signed-off-by: Dinesh G Dutt <ddutt@cumulusnetworks.com>
Reviewed-By: Vivek Venkataram <vivek@cumulusnetworks.com>
This patch also adds BFD multihop support for BGP. Whether a peer is multi-hop or single hop is determined internally. All IGP peers are considered as multi-hop peers. EBGP peers are considered as single hop unless configured as multi-hop.
BGP BFD command enhancement to configure BFD parameters (detect multiplier, min rx and min tx).
router bgp <as-number>
neighbor <name/ip-address> bfd <detect mult> <min rx> <min tx>
Signed-off-by: Radhika Mahankali <radhika@cumulusnetworks.com>
Reviewed-by: Dinesh G Dutt <ddutt@cumulusnetworks.com>
Reviewed-by: Vipin Kumar <vipin@cumulusnetworks.com>
Reviewed-by: Kanna Rajagopal <kanna@cumulusnetworks.com>
"bgp confederation id X" are the same value.
router bgp 1
bgp router-id 10.1.1.1
bgp confederation identifier 1
bgp confederation peers 24 35
neighbor 10.1.1.2 remote-as 24
neighbor 10.1.1.2 update-source lo
neighbor 10.1.1.3 remote-as 1
neighbor 10.1.1.3 update-source lo
The customer does this because they want to peer to 10.1.1.2 as a
confed-external peer but peer with 10.1.1.3 as a normal iBGP peer.
The bug was that we thought 10.1.1.3 was an EBGP peer so we did not send him
LOCALPREF which caused the Juniper to send us a NOTIFICATION. I confirmed
that quagga also sends a NOTIFICATION in this scenario.
The fix is to add a check to see if router bgp X and bgp confederation
identifier X are equal because that is a factor in determining if a peer is
EBGP or IBGP
Additional issues fixed in the this patch:
We were not properly removing all AS_CONFED_SEQUENCEs/SETs from the aspath
when advertising a route to an ebgp peer. This was due to two issues:
We only called aspath_delete_confed_seq() if confederations were
configured. We can RX as aspath with CONFED segments even if
confederations are not configured.
aspath_delete_confed_seq() was implemented based on the original confed
RFC 3065 which basically said "remove all of the leading
AS_CONFED_SEQUENCEs/SETs" where the new confed RFC 5065 says "remove ALL
of the AS_CONFED_SEQUENCEs/SETs"
peer-groups did not work for confed-external peers. peer_calc_sort() always
returned BGP_PEER_EBGP for a confederations where the remote-as was not
specified. The reason was the peer->as_type was AS_UNSPECIFIED but we checked
if (peer->as_type != AS_SPECIFIED)
return (peer->as_type == AS_INTERNAL ? BGP_PEER_IBGP : BGP_PEER_EBGP);
After fixing that I found that when we got to the else where we checked for
peer1 we could only possibly return BGP_PEER_IBGP or BGP_PEER_EBGP, we need
to also be able to return BGP_PEER_CONFED. I changed this to return
peer1->sort.
"show ip bgp x.x.x.x" would always display "Local" for the aspath. This is
because we were calling aspath_counts_hop() to determine if the aspath was
empty. This is wrong though because CONFED segments do not count towards
aspath hopcount. The fix is to null check aspath->segments to determine if
the aspath is actually empty.
"show ip bgp x.x.x.x" and "show ip bgp neighbor" always displayed
"internal" or "external" and never "confed-internal" or "confed-external".
This made troubleshooting difficult because I couldn't tell exactly what
kind of peer I was dealing with. I added the confed-internal and
confed-external output...also added a "peer-type" field in the json output
for 'show ip bgp x.x.x.x'
"show ip bgp peer-group" did not list the peer-group name if we hadn't
determined the "type" (internal, external, etc) for the peer-group
This adds support for BGP RFC 5549 (Extended Next Hop Encoding capability)
* send and receive of the capability
* processing of IPv4->IPv6 next-hops
* for resolving these IPv6 next-hops, itsworks with the current
next-hop-tracking support
* added a new message type between BGP and Zebra for such route
install/uninstall
* zserv side of changes to process IPv4 prefix ->IPv6 next-hops
* required show command changes for IPv4 prefix having IPv6 next-hops
Few points to note about the implementation:
* It does an implicit next-hop-self when a [IPv4 prefix -> IPv6 LL next-hop]
is to be considered for advertisement to IPv4 peering (or IPv6 peering
without Extended next-hop capability negotiated)
* Currently feature is off by default, enable it by configuring
'neighbor <> capability extended-nexthop'
* Current support is for IPv4 Unicast prefixes only.
IMPORTANT NOTE:
This patch alone isn't enough to have IPv4->IPv6 routes installed into
the kernel. A separate patch is needed for that to work for the netlink
interface.
Signed-off-by: Vipin Kumar <vipin@cumulusnetworks.com>
Reviewed-by: Daniel Walton <dwalton@cumulusnetworks.com>
Vivek Venkatraman <vivek@cumulusnetworks.com>
Donald Sharp <sharpd@cumulusnetworks.com>
Table-id argument support wasnt complete, used the [proto, instance]
combination changes that were done for OSPF multi-instance. In this case
its 'table <table-id>' just like it was 'ospf <instance-id>'
bgpd: Exchange hostname capability and display hostnames in outputs
This patch adds a hostname capability. The node's hostname and
domainname are exchanged in the new capability and used in show command
outputs based on a knob enabled by the user. The hostname and domainname
can be a maximum of 64 chars long, each.
Signed-off-by: Dinesh G Dutt <ddutt@cumulusnetworks.com>
Reviewed-by: Daniel Walton <dwalton@cumulusnetworks.com>
Reviewed-by: Vivek Venkataraman <vivek@cumulusnetworks.com>
bgp: Fixup of the remote-as command to allow user to not have to enter an actual as number
Signed-off-by: Donald Sharp<sharpd@cumulusnetworks.com>
Reviewed-by:
BGP: Fix network import check use with NHT instead of scanner
When next hop tracking was implemented and the bgp scanner was eliminated,
the "network import-check" command got broken. This patch fixes that
issue. NHT is used to not just track nexthops, but also the static routes
that are announced as part of BGP's network command. The routes are
registered only when import-check is enabled. To optimize performance,
we register static routes only when import-check is enabled.
Signed-off-by: Dinesh G Dutt <ddutt@cumulusnetworks.com>
show update-groups summary was mislabeled. What it displays is not a summary
at all, but the detailed info about all update-groups. Furthermore, there
was no way to get detailed info about a specific subgroup.
This patch renames "show * update-groups summary" to "show * update-groups"
and adds an option to see the info specific to a subgroup only. It also
validates the subgroup-id.
show * update-groups summary will be added separately.
sockunion_same() and bgp_peer_conf_if_to_su_update() need to use the scope_id
field of the ipv6 address to uniquify/identify the address.
This allows sessions based on link local address when that address is not
unique across peers.
In the data center, in conjunction with next hop propagation for features
such as announcing VIP routes to load balancers and such, it is desired to
disable the connected route check even on ebgp peers with TTL of 1. This
patch is used to disable the check for all peers instead of the peer by
peer check that is currently supported. Furthermore, the existing
disable-connected-check is different from how Cisco implements this feature.
So, we add this new flag to avoid reliance on the existing flag.
Signed-off-by: Dinesh G Dutt <ddutt@cumulusnetworks.com>
Reviewed-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
sessions dynamically. The operator configures a range of neighbor addresses
to which peering is allowed. The ranges are configured as subnets and
multiple ranges are allowed. Each range is associated with a peer-group
so that additional parameters can be configured.
BGP neighbor sessions are dynamically created when connections are initiated
by remote neighbors whose addresses fall within a configured range. The
sessions are deleted when the BGP connection terminates.
A limit on the number of neighbors allowed from each range of addresses
can be specified.
IPv4 and IPv6 peering is supported. Over the peering, any of the address
families configured for the peer-group can be negotiated.
This patch implements the 'update-groups' functionality in BGP. This is a
function that can significantly improve BGP performance for Update generation
and resultant network convergence. BGP Updates are formed for "groups" of
peers and then replicated and sent out to each peer rather than being formed
for each peer. Thus major BGP operations related to outbound policy
application, adj-out maintenance and actual Update packet formation
are optimized.
BGP update-groups dynamically groups peers together based on configuration
as well as run-time criteria. Thus, it is more flexible than update-formation
based on peer-groups, which relies on operator configuration.
[Note that peer-group based update formation has been introduced into BGP by
Cumulus but is currently intended only for specific releases.]
From 11098af65b2b8f9535484703e7f40330a71cbae4 Mon Sep 17 00:00:00 2001
Subject: [PATCH] updgrp commits
The problem is that zclient->redist[ZEBRA_ROUTE_MAX] used for storing a
client’s redist state, has no address-family qualification. This means
a client can only store its interest in a protocol (connected, static etc.),
but cant choose IPv4 or ipv6 with that. This hindered implementation on
client sides to manage redistribution of ipv4 and ipv6 both.
BGP's redistribution of protocols like connected/static is one such place.
One fix could be to overload this and flap the redist connection each time
any new afi is added for redist, but that may have side-effects on the
existing afi redist.
The cleaner way is to modify redist data-structure to also take AFI, and adjust
routines that deal with it, so that a client can register for a protocol
redistribution based on the AFI. BGP already maintains redistribution state
based on afi and protocol (bgp->redist[AFI_MAX][ZEBRA_ROUTE_MAX]). This patch
takes care of filling up the gap in zclient/zserv redistribution state to
also use AFI qualification.
Signed-off-by: Vipin Kumar <vipin@cumulusnetworks.com>
Reviewed-by: Daniel Walton <dwalton@cumulusnetworks.com>
Reviewed-by: Dinesh G Dutt <ddutt@cumulusnetworks.com>
Zebra: Redistribute routes from non-main kernel table to main.
This can be the basis for many interesting features such as variations
of redistribute ARP, using zebra as the RIB in the presence of multiple
routing protocol stacks etc. The code only supports IPv4 for now, but
the infrastructure is in place for IPv6.
Usage:
There is a new route type introduced by this model: TABLE. Routes
imported from alternate kernel tables will have their protocol type set to
TABLE.
Routes from alternate kernel tables MUST be first imported into the main
table via "ip import-table <table id>". They can then be redistributed via
a routing protocol via the "redistribute table" command. Each imported table
can an optional administrative distance specified. In Zebra, a route with a
lower distance is chosen over routes with a higher distance. So, distance
is how the user can choose to prioritize routes from a particular table over
routes from other tables or routes learnt another way in zebra.
Route maps for imported tables are specified via "ip protocol" command in
zebra. Route maps for redistributed routes within a routing protocol are
subject to the route map options supported by the protocol. The
"match source-protocol" option in route maps can match against "table"
to filter routes learnt from alternate kernel routing tables.
Signed-off-by: Dinesh G Dutt <ddutt@cumulusnetworks.com>
——————————————-------------
- etc/init.d/quagga is modified to support creating separate ospf daemon
process for each instance. Each individual instance is monitored by
watchquagga just like any protocol daemons.(requires initd-mi.patch).
- Vtysh is modified to able to connect to multiple daemons of the same
protocol (supported for OSPF only for now).
- ospfd is modified to remember the Instance-ID that its invoked with. For
the entire life of the process it caters to any command request that
matches that instance-ID (unless its a non instance specific command).
Routes/messages to zebra are tagged with instance-ID.
- zebra route/redistribute mechanisms are modified to work with
[protocol type + instance-id]
- bgpd now has ability to have multiple instance specific redistribution
for a protocol (OSPF only supported/tested for now).
- zlog ability to display instance-id besides the protocol/daemon name.
- Changes in other daemons are to because of the needed integration with
some of the modified APIs/routines. (Didn’t prefer replicating too many
separate instance specific APIs.)
- config/show/debug commands are modified to take instance-id argument
as appropriate.
Guidelines to start using multi-instance ospf
---------------------------------------------
The patch is backward compatible, i.e for any previous way of single ospf
deamon(router ospf <cr>) will continue to work as is, including all the
show commands etc.
To enable multiple instances, do the following:
1. service quagga stop
2. Modify /etc/quagga/daemons to add instance-ids of each desired
instance in the following format:
ospfd=“yes"
ospfd_instances="1,2,3"
assuming you want to enable 3 instances with those instance ids.
3. Create corresponding ospfd config files as ospfd-1.conf, ospfd-2.conf
and ospfd-3.conf.
4. service quagga start/restart
5. Verify that the deamons are started as expected. You should see
ospfd started with -n <instance-id> option.
ps –ef | grep quagga
With that /var/run/quagga/ should have ospfd-<instance-id>.pid and
ospfd-<instance-id>/vty to each instance.
6. vtysh to work with instances as you would with any other deamons.
7. Overall most quagga semantics are the same working with the instance
deamon, like it is for any other daemon.
NOTE:
To safeguard against errors leading to too many processes getting invoked,
a hard limit on number of instance-ids is in place, currently its 5.
Allowed instance-id range is <1-65535>
Once daemons are up, show running from vtysh should show the instance-id
of each daemon as 'router ospf <instance-id>’ (without needing explicit
configuration)
Instance-id can not be changed via vtysh, other router ospf configuration
is allowed as before.
Signed-off-by: Vipin Kumar <vipin@cumulusnetworks.com>
Reviewed-by: Daniel Walton <dwalton@cumulusnetworks.com>
Reviewed-by: Dinesh G Dutt <ddutt@cumulusnetworks.com>
Summary of changes
- added an option to enable keepalive debugs for a specific peer
- added an option to enable inbound and/or outbound updates debugs for a specific peer
- added an option to enable update debugs for a specific prefix
- added an option to enable zebra debugs for a specific prefix
- combined "deb bgp", "deb bgp events" and "deb bgp fsm" into "deb bgp neighbor-events". "deb bgp neighbor-events" can be enabled for a specific peer.
- merged "deb bgp filters" into "deb bgp update"
- moved the per-peer logging to one central log file. We now have the ability to filter all verbose debugs on a per-peer and per-prefix basis so we no longer need to keep log files per-peer. This simplifies troubleshooting by keeping all BGP logs in one location. The use
r can then grep for the peer IP they are interested in if they wish to see the logs for a specific peer.
- Changed "show debugging" in isis to "show debugging isis" to be consistent with all other protocols. This was very confusing for the user because they would type "show debug" and expect to see a list of debugs enabled across all protocols.
- Removed "undebug" from the parser for BGP. Again this was to be consisten with all other protocols.
- Removed the "all" keyword from the BGP debug parser. The user can now do "no debug bgp" to disable all BGP debugs, before you had to type "no deb all bgp" which was confusing.
The new parse tree for BGP debugging is:
deb bgp as4
deb bgp as4 segment
deb bgp keepalives [A.B.C.D|WORD|X:X::X:X]
deb bgp neighbor-events [A.B.C.D|WORD|X:X::X:X]
deb bgp nht
deb bgp updates [in|out] [A.B.C.D|WORD|X:X::X:X]
deb bgp updates prefix [A.B.C.D/M|X:X::X:X/M]
deb bgp zebra
deb bgp zebra prefix [A.B.C.D/M|X:X::X:X/M]
protocols. BGP and OSPF are integrated to respond this BFD session down message
originated in Zebra via ptmd.
BGP and OSPF now have a bfd command, which tells OSPF/BGP to respond to the
BFD session down message.
OSPF:
interface <>
ip ospf bfd
BGP:
router bgp <>
neighbor <> bfd
Please note that these commands don't enable BFD as a protocol. BFD configuration
and paramter tuning are via BFD applicable UI.
Signed-off-by: Vipin Kumar <vipin@cumulusnetworks.com>
Reviewed-by: Shrijeet Mukherjee <shm@cumulusnetworks.com>
BGP: Reprocess the trigger points when an attached route map changes
Currently, modifications to route maps do not affect already processed
routes; they only affect new route updates. This patch addresses this
limitation.
Signed-off-by: Dinesh G Dutt <ddutt@cumulusnetworks.com>
COMMAND:
Possible forms of the command configuration:
[no] bgp max-med administrative
[no] bgp max-med administrative <max-med-value>
[no] bgp max-med on-startup <period>
[no] bgp max-med on-startup <period> <max-med-value>
DESCRIPTION:
'administrative' takes effect from the time of the config until the config is
removed.
'on-startup' is effective only at the startup time for the given '<period>'
after the first peer is established.
'<max-med-value>' is used as the MED value to be sent out when the max-med
is effective. Default max-med value is 4294967294.
NOTE:
When max-med is active, MED is changed only in the outgoing attributes to the
peers, it doesn't modify any MED specific state of the attributes in BGP on
the local node.
Signed-off-by: Vipin Kumar <vipin@cumulusnetworks.com>
Reviewed-by: Daniel Walton <dwalton@cumulusnetworks.com>
ISSUE:
During startup, BGP update prefix packing wasnt optimal and route installation
was found to be spread over.
SOLUTION:
With this patch, update-delay post processing is serialized to achieve:
a. better peer update packing
(which helps in reducing total number of BGP update packets)
b. installation of the resulting routes in zebra as close to each others
as possible.
(which can help zebra batch its processing and updates to Kernel better)
BGPd: Allow route-map policy modifications to also affect route reflectors.
By default, attribute modification via route-map policy out is ignored on
reflected routes. This patch provides an option to allow this modification
to occur. Once enabled, it affects all reflected routes.
Signed-off-by: Dinesh G Dutt <ddutt@cumulusnetworks.com>
BGP: Fix FSM to handle active/passive connections better
The existing code didn't work well when dual connections resulted between
peers during session bringup. This patch fixes that.
Signed-off-by: Dinesh G Dutt <ddutt@cumulusnetworks.com>
BGP: Event-driven route announcement taking into account min route advertisement interval
ISSUE
BGP starts the routeadv timer (peer->t_routeadv) to expire in 1 sec
when a peer is established. From then on, the timer expires
periodically based on the configured MRAI value (default: 30sec for
EBGP, 5sec for IBGP). At the expiry, the write thread is triggered
that takes the routes from peer's sync FIFO (adj-rib-out) and sends
UPDATEs. This has a few drawbacks:
(1) Delay in new route announcement: Even when the last UPDATE message
was sent a while back, the next route change will necessarily have
to wait for routeadv expiry
(2) CPU usage: The timer is always armed. If the operator chooses to
configure a lower value of MRAI (zero second is a preferred choice
in many deployments) for better convergence, it leads to high CPU
usage for BGP process, even at the times of no network churn.
PATCH
Make the route advertisement event-driven - When routes are added to
peer's sync FIFO, check if the routeadv timer needs to be adjusted (or
started). Conversely, do not arm the routeadv timer unconditionally.
The patch also addresses route announcements during read-only mode
(update-delay). During read-only mode operation, the routeadv timer
is not started. When BGP comes out of read-only mode and all the
routes are processed, the timer is started for all peers with zero
expiry, so that the UPDATEs can be sent all at once. This leads to
(near-)optimal UPDATE packing.
Finally, the patch makes the "max # packets to write to peer socket at
a time" configurable. Currently it is hard-coded to 10. The command is
at the top router-bgp mode and is called "write-quanta <number>". It
is a useful convergence parameter to tweak.
Signed-off-by: Pradosh Mohapatra <pmohapat@cumulusnetworks.com>
Reviewed-by: Daniel Walton <dwalton@cumulusnetworks.com>
BGP: Show more meaningful outq value in 'show ip bgp summary' output.
'outq' field in 'show ip bgp sum' displays the number of formatted packets
to a peer. Since the route announcement follows an input-buffered pattern
(i.e. adj-rib-out is a separate queue of routes per peer and packets are
formatted from the routes at the time of TCP write), the outq field doesn't
show any interesting data worth watching.
The patch is to display the adj-rib-out queue depth instead.
signed-off-by: pmohapat@cumulusnetworks.com
reviewed-by: dwalton@cumulusnetworks.com
COMMAND:
table-map <route-map-name>
DESCRIPTION:
This feature is used to apply a route-map on route updates from BGP to Zebra.
All the applicable match operations are allowed, such as match on prefix,
next-hop, communities, etc. Set operations for this attach-point are limited
to metric and next-hop only. Any operation of this feature does not affect
BGPs internal RIB.
Supported for ipv4 and ipv6 address families. It works on multi-paths as well,
however, metric setting is based on the best-path only.
IMPLEMENTATION NOTES:
The route-map application at this point is not supposed to modify any of BGP
route's attributes (anything in bgp_info for that matter). To achieve that,
creating a copy of the bgp_attr was inevitable. Implementation tries to keep
the memory footprint low, code comments do point out the rationale behind a
few choices made.
bgp_zebra_announce() was already a big routine, adding this feature would
extend it further. Patch has created a few smaller routines/macros whereever
possible to keep the size of the routine in check without compromising on the
readability of the code/flow inside this routine.
For updating a partially filtered route (with its nexthops), BGP to Zebra
replacement semantic of the next-hops serves the purpose well. However, with
this patch there could be some redundant withdraws each time BGP announces a
route thats (all the nexthops) gets denied by the route-map application.
Handling of this case could be optimized by keeping state with the prefix and
the nexthops in BGP. The patch doesn't optimizing that case, as even with the
redundant withdraws the total number of updates to zebra are still be capped
by the total number of routes in the table.
Signed-off-by: Vipin Kumar <vipin@cumulusnetworks.com>
Reviewed-by: Pradosh Mohapatra <pmohapat@cumulusnetworks.com>
COMMAND:
'update-delay <max-delay in seconds> [<establish-wait in seconds>]'
DESCRIPTION:
This feature is used to enable read-only mode on BGP process restart or when
BGP process is cleared using 'clear ip bgp *'. When applicable, read-only mode
would begin as soon as the first peer reaches Established state and a timer
for <max-delay> seconds is started.
During this mode BGP doesn't run any best-path or generate any updates to its
peers. This mode continues until:
1. All the configured peers, except the shutdown peers, have sent explicit EOR
(End-Of-RIB) or an implicit-EOR. The first keep-alive after BGP has reached
Established is considered an implicit-EOR.
If the <establish-wait> optional value is given, then BGP will wait for
peers to reach establish from the begining of the update-delay till the
establish-wait period is over, i.e. the minimum set of established peers for
which EOR is expected would be peers established during the establish-wait
window, not necessarily all the configured neighbors.
2. max-delay period is over.
On hitting any of the above two conditions, BGP resumes the decision process
and generates updates to its peers.
Default <max-delay> is 0, i.e. the feature is off by default.
This feature can be useful in reducing CPU/network used as BGP restarts/clears.
Particularly useful in the topologies where BGP learns a prefix from many peers.
Intermediate bestpaths are possible for the same prefix as peers get established
and start receiving updates at different times. This feature should offer a
value-add if the network has a high number of such prefixes.
IMPLEMENTATION OBJECTIVES:
Given this is an optional feature, minimized the code-churn. Used existing
constructs wherever possible (existing queue-plug/unplug were used to achieve
delay and resume of best-paths/update-generation). As a result, no new
data-structure(s) had to be defined and allocated. When the feature is disabled,
the new node is not exercised for the most part.
Signed-off-by: Vipin Kumar <vipin@cumulusnetworks.com>
Reviewed-by: Pradosh Mohapatra <pmohapat@cumulusnetworks.com>
Dinesh Dutt <ddutt@cumulusnetworks.com>
A fat tree topology running IBGP gets into two issues with anycast address
routing. Consider the following topology:
R9 R10
x x
R3 R4 R7 R8
x x
R1 R2 R5 R6
| | | |
10/8 10/8 10/8 S
Let's remind ourselves of BGP decision process steps:
1. Highest Local Preference
2. Shortest AS Path Length
3. Lowest Origin Type
4. Lowest MED (Multi-Exit Discriminator)
5. Prefer External to Internal
6. Closest Egress (Lowest IGP Distance)
7. Tie Breaking (Lowest-Router-ID)
8. Tie Breaking (Lowest-cluster-list length)
9. Tie Breaking (Lowest-neighbor-address)
Without any policies, steps 1-6 will almost always evaluate identically for
all paths received on any router in the above topology. Let's assume that
the router-ids follow the following inequality: R1 < R2 < R5 < R6. Owing to
the 7th step above, all routers will now choose R1's path as the best. This
is undesirable. As an example, traffic from S to 10/8 will follow the path
S -> R6 -> R7 -> R9 -> R4 -> R2 -> 10/8 instead of S -> R6 -> R7 -> R5 -> 10/8.
Furthermore, once R7 (& R8) chooses R1's path as the best, it would withdraw
its path learned through (R5, R6) from (R9, R10). This leads to inefficient
load balancing - e.g. R9 can't do ECMP across all available egresses -
(R1, R2, R5).
The patch addresses these issues by noting that that cluster list is always
carried along with the routes and its length is a good indicator of IBGP
hops. It thus makes sense to compare that as an extension to metric after
step 6. That automatically ensures correct multipath computation.
Unfortunately a partial deployment of this in a generic topology (note:
fat-tree/clos topologies work fine) may lead to potential loops. It needs
to be looked into.
Signed-off-by: Pradosh Mohapatra <pmohapat@cumulusnetworks.com>
Reviewed-by: Dinesh G Dutt <ddutt@cumulusnetworks.com>
