Do not allow an upper level protocol to send a route to
zebra that is a /32 or a /128 that recurses through itself.
Current behavior:
donna.cumulusnetworks.com# show ip route
Codes: K - kernel route, C - connected, S - static, R - RIP,
O - OSPF, I - IS-IS, B - BGP, E - EIGRP, N - NHRP,
T - Table, v - VNC, V - VNC-Direct, A - Babel, D - SHARP,
F - PBR, f - OpenFabric,
> - selected route, * - FIB route, q - queued route, r - rejected route
K>* 0.0.0.0/0 [0/104] via 10.0.2.2, enp0s3, 01:05:28
C>* 10.0.2.0/24 is directly connected, enp0s3, 00:01:50
C>* 192.168.209.0/24 is directly connected, enp0s8, 01:05:28
C>* 192.168.210.0/24 is directly connected, enp0s9, 01:05:28
D>* 192.168.210.43/32 [150/0] via 192.168.210.44, enp0s9, 01:01:57
D 192.168.210.44/32 [150/0] via 192.168.210.44 inactive, 01:05:15
C>* 192.168.212.0/24 is directly connected, enp0s10, 01:05:28
donna.cumulusnetworks.com# sharp install routes 40.0.0.1 nexthop 192.168.210.44
% Command incomplete: sharp install routes 40.0.0.1 nexthop 192.168.210.44
donna.cumulusnetworks.com# sharp install routes 40.0.0.1 nexthop 192.168.210.44 1
donna.cumulusnetworks.com# end
donna.cumulusnetworks.com# show ip route
Codes: K - kernel route, C - connected, S - static, R - RIP,
O - OSPF, I - IS-IS, B - BGP, E - EIGRP, N - NHRP,
T - Table, v - VNC, V - VNC-Direct, A - Babel, D - SHARP,
F - PBR, f - OpenFabric,
> - selected route, * - FIB route, q - queued route, r - rejected route
K>* 0.0.0.0/0 [0/104] via 10.0.2.2, enp0s3, 01:05:51
C>* 10.0.2.0/24 is directly connected, enp0s3, 00:00:12
D>* 40.0.0.1/32 [150/0] via 192.168.210.44, enp0s9, 00:00:03
C>* 192.168.209.0/24 is directly connected, enp0s8, 01:05:51
C>* 192.168.210.0/24 is directly connected, enp0s9, 01:05:51
D>* 192.168.210.43/32 [150/0] via 192.168.210.44, enp0s9, 01:02:20
D 192.168.210.44/32 [150/0] via 192.168.210.44 inactive, 01:05:38
C>* 192.168.212.0/24 is directly connected, enp0s10, 01:05:51
donna.cumulusnetworks.com#
Fixed behavior:
donna.cumulusnetworks.com# sharp install routes 192.168.210.44 nexthop 192.168.210.44 1
donna.cumulusnetworks.com# show ip route
Codes: K - kernel route, C - connected, S - static, R - RIP,
O - OSPF, I - IS-IS, B - BGP, E - EIGRP, N - NHRP,
T - Table, v - VNC, V - VNC-Direct, A - Babel, D - SHARP,
F - PBR, f - OpenFabric,
> - selected route, * - FIB route, q - queued route, r - rejected route
K>* 0.0.0.0/0 [0/104] via 10.0.2.2, enp0s3, 00:00:15
C>* 10.0.2.0/24 is directly connected, enp0s3, 00:00:15
C>* 192.168.209.0/24 is directly connected, enp0s8, 00:00:15
C>* 192.168.210.0/24 is directly connected, enp0s9, 00:00:15
D 192.168.210.44/32 [150/0] via 192.168.210.44 inactive, 00:00:03
C>* 192.168.212.0/24 is directly connected, enp0s10, 00:00:15
donna.cumulusnetworks.com# sharp install routes 40.0.0.1 nexthop 192.168.210.44 1
donna.cumulusnetworks.com# show ip route
Codes: K - kernel route, C - connected, S - static, R - RIP,
O - OSPF, I - IS-IS, B - BGP, E - EIGRP, N - NHRP,
T - Table, v - VNC, V - VNC-Direct, A - Babel, D - SHARP,
F - PBR, f - OpenFabric,
> - selected route, * - FIB route, q - queued route, r - rejected route
K>* 0.0.0.0/0 [0/104] via 10.0.2.2, enp0s3, 00:00:24
C>* 10.0.2.0/24 is directly connected, enp0s3, 00:00:24
D>* 40.0.0.1/32 [150/0] via 192.168.210.44, enp0s9, 00:00:02
C>* 192.168.209.0/24 is directly connected, enp0s8, 00:00:24
C>* 192.168.210.0/24 is directly connected, enp0s9, 00:00:24
D 192.168.210.44/32 [150/0] via 192.168.210.44 inactive, 00:00:12
C>* 192.168.212.0/24 is directly connected, enp0s10, 00:00:24
donna.cumulusnetworks.com#
This behavior came up from discussion around issue #5159. Where
OSPF was receiving a route through itself as part of the router link
lsa. I currently think that ospf should probably dissallow this in ospf
but we should also do the right thing in zebra. If we do not allow this
change we can have situations where ordering of routes into zebra suddenly
matters.
Fixes: #5159
Signed-off-by: Donald Sharp <sharpd@cumulsunetworks.com>
If the nexthop is of type `GATEWAY_IFINDEX` then the nexthop
should not resolve to a nexthop that has a different ifindex
from the one given.
Signed-off-by: Stephen Worley <sworley@cumulusnetworks.com>
even if vty commands were available, the default resolution command was
working only for the first vrf configured. others were ignored. Also,
for nexthop, resolution was working for all vrfs, and not the specific
one.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
When resolving a nexthop, append its labels to the one its
resolving to along with the labels that may already be present there.
Before we were ignoring labels if the resolving level was greater than
two.
Before:
```
S> 2.2.2.2/32 [1/0] via 7.7.7.7 (recursive), label 2222, 00:00:07
* via 7.7.7.7, dummy1 onlink, label 1111, 00:00:07
S> 3.3.3.3/32 [1/0] via 2.2.2.2 (recursive), label 3333, 00:00:04
* via 7.7.7.7, dummy1 onlink, label 1111, 00:00:04
K>* 7.7.7.7/32 [0/0] is directly connected, dummy1, label 1111, 00:00:17
C>* 192.168.122.0/24 is directly connected, ens3, 00:00:17
K>* 192.168.122.1/32 [0/100] is directly connected, ens3, 00:00:17
ubuntu_nh#
```
This patch:
```
S> 2.2.2.2/32 [1/0] via 7.7.7.7 (recursive), label 2222, 00:00:04
* via 7.7.7.7, dummy1 onlink, label 1111/2222, 00:00:04
S> 3.3.3.3/32 [1/0] via 2.2.2.2 (recursive), label 3333, 00:00:02
* via 7.7.7.7, dummy1 onlink, label 1111/2222/3333, 00:00:02
K>* 7.7.7.7/32 [0/0] is directly connected, dummy1, label 1111, 00:00:11
C>* 192.168.122.0/24 is directly connected, ens3, 00:00:11
K>* 192.168.122.1/32 [0/100] is directly connected, ens3, 00:00:11
ubuntu_nh#
```
Signed-off-by: Stephen Worley <sworley@cumulusnetworks.com>
If there is a recursive route resolved over blackhole route, then
the resolved blackhole_type is not getting set correctly.
This fix updates the bh_type correctly for resursive routes.
Signed-off-by: vishaldhingra <vdhingra@vmware.com>
The flag ROUTE_ENTRY_NEXTHOPS_CHANGED is only ever set or unset.
Since this flag is not used for anything useful, remove from system.
By changing this flag we have re-ordered `internalStatus' of json
output of zebra rib routes. Go through and fix up tetsts to
use the new values.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Introducing a 3rd state for route_map_apply library function: RMAP_NOOP
Traditionally route map MATCH rule apis were designed to return
a binary response, consisting of either RMAP_MATCH or RMAP_NOMATCH.
(Route-map SET rule apis return RMAP_OKAY or RMAP_ERROR).
Depending on this response, the following statemachine decided the
course of action:
State1:
If match cmd returns RMAP_MATCH then, keep existing behaviour.
If routemap type is PERMIT, execute set cmds or call cmds if applicable,
otherwise PERMIT!
Else If routemap type is DENY, we DENYMATCH right away
State2:
If match cmd returns RMAP_NOMATCH, continue on to next route-map. If there
are no other rules or if all the rules return RMAP_NOMATCH, return DENYMATCH
We require a 3rd state because of the following situation:
The issue - what if, the rule api needs to abort or ignore a rule?:
"match evpn vni xx" route-map filter can be applied to incoming routes
regardless of whether the tunnel type is vxlan or mpls.
This rule should be N/A for mpls based evpn route, but applicable to only
vxlan based evpn route.
Also, this rule should be applicable for routes with VNI label only, and
not for routes without labels. For example, type 3 and type 4 EVPN routes
do not have labels, so, this match cmd should let them through.
Today, the filter produces either a match or nomatch response regardless of
whether it is mpls/vxlan, resulting in either permitting or denying the
route.. So an mpls evpn route may get filtered out incorrectly.
Eg: "route-map RM1 permit 10 ; match evpn vni 20" or
"route-map RM2 deny 20 ; match vni 20"
With the introduction of the 3rd state, we can abort this rule check safely.
How? The rules api can now return RMAP_NOOP to indicate
that it encountered an invalid check, and needs to abort just that rule,
but continue with other rules.
As a result we have a 3rd state:
State3:
If match cmd returned RMAP_NOOP
Then, proceed to other route-map, otherwise if there are no more
rules or if all the rules return RMAP_NOOP, then, return RMAP_PERMITMATCH.
Signed-off-by: Lakshman Krishnamoorthy <lkrishnamoor@vmware.com>
Add a file that exposes functions which modify nexthop groups.
Nexthop groups are techincally immutable but there are a
few special cases where we need direct access to add/remove
nexthops after the group has been made. This file provides a
way to expose those functions in a way that makes it clear
this is a private/hidden api.
Signed-off-by: Stephen Worley <sworley@cumulusnetworks.com>
Introducing a 3rd state for route_map_apply library function: RMAP_NOOP
Traditionally route map MATCH rule apis were designed to return
a binary response, consisting of either RMAP_MATCH or RMAP_NOMATCH.
(Route-map SET rule apis return RMAP_OKAY or RMAP_ERROR).
Depending on this response, the following statemachine decided the
course of action:
Action: Apply route-map match and return the result (RMAP_MATCH/RMAP_NOMATCH)
State1: Receveived RMAP_MATCH
THEN: If Routemap type is PERMIT, execute other rules if applicable,
otherwise we PERMIT!
Else: If Routemap type is DENY, we DENYMATCH right away
State2: Received RMAP_NOMATCH, continue on to next route-map, otherwise,
return DENYMATCH by default if nothing matched.
With reference to PR 4078 (https://github.com/FRRouting/frr/pull/4078),
we require a 3rd state because of the following situation:
The issue - what if, the rule api needs to abort or ignore a rule?:
"match evpn vni xx" route-map filter can be applied to incoming routes
regardless of whether the tunnel type is vxlan or mpls.
This rule should be N/A for mpls based evpn route, but applicable to only
vxlan based evpn route.
Today, the filter produces either a match or nomatch response regardless of
whether it is mpls/vxlan, resulting in either permitting or denying the
route.. So an mpls evpn route may get filtered out incorrectly.
Eg: "route-map RM1 permit 10 ; match evpn vni 20" or
"route-map RM2 deny 20 ; match vni 20"
With the introduction of the 3rd state, we can abort this rule check safely.
How? The rules api can now return RMAP_NOOP (or another enum) to indicate
that it encountered an invalid check, and needs to abort just that rule,
but continue with other rules.
Question: Do we repurpose an existing enum RMAP_OKAY or RMAP_ERROR
as the 3rd state (or create a new enum like RMAP_NOOP)?
RMAP_OKAY and RMAP_ERROR are used to return the result of set cmd.
We chose to go with RMAP_NOOP (but open to ideas),
as a way to bypass the rmap filter
As a result we have a 3rd state:
State3: Received RMAP_NOOP
Then, proceed to other route-map, otherwise return RMAP_PERMITMATCH by default.
Signed-off-by:Lakshman Krishnamoorthy <lkrishnamoor@vmware.com>
Since these functions are not really rib processing problems
let's move them to zebra_nhg.c which is meant for processing of
nexthop groups.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
