Add a new topotest that features a topology with seven routers spread
across four OSPF areas:
* 1 backbone area;
* 1 regular non-backbone area (0.0.0.1);
* 1 stub area (0.0.0.2);
* 1 NSSA area (0.0.0.3).
All routers have both GR and GR helper functionality enabled in
the configuration. The test consists of restarting each router,
one at time, and checking that all forwarding planes (and LSDBs)
are kept intact during those restarts.
A successful run takes about three minutes to finish.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Using "write memory" to save the daemons' configurations before
restarting them can cause log files to stop working correctly. Add
a new "save_config" to the kill_router_daemons() function to prevent
that from happening when saving the configurations isn't necessary.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
RFC 3623 specifies the Graceful Restart enhancement to the OSPF
routing protocol. This PR implements support for the restarting mode,
whereas the helper mode was implemented by #6811.
This work is based on #6782, which implemented the pre-restart part
and settled the foundations for the post-restart part (behavioral
changes, GR exit conditions, and on-exit actions).
Here's a quick summary of how the GR restarting mode works:
* GR can be enabled on a per-instance basis using the `graceful-restart
[grace-period (1-1800)]` command;
* To perform a graceful shutdown, the `graceful-restart prepare ospf`
EXEC-level command needs to be issued before restarting the ospfd
daemon (there's no specific requirement on how the daemon should
be restarted);
* `graceful-restart prepare ospf` will initiate the graceful restart
for all GR-enabled instances by taking the following actions:
o Flooding Grace-LSAs over all interfaces
o Freezing the OSPF routes in the RIB
o Saving the end of the grace period in non-volatile memory (a JSON
file stored in `$frr_statedir`)
* Once ospfd is started again, it will follow the procedures
described in RFC 3623 until it detects it's time to exit the graceful
restart (either successfully or unsuccessfully).
Testing done:
* New topotest featuring a multi-area OSPF topology (including stub
and NSSA areas);
* Successful interop tests against IOS-XR routers acting as helpers.
Co-authored-by: GalaxyGorilla <sascha@netdef.org>
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Both the GR helper code and the upcoming GR restarting code are going
to share a lot of definitions. As such, rename ospf_gr_helper.h to
ospf_gr.h, which will be the central point of all GR definitions
and prototypes.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Remove previous log config
debug ospf graceful-restart helper
and just use
debug ospf graceful-restart
for everything related to OSPF GR.
Signed-off-by: GalaxyGorilla <sascha@netdef.org>
Log the LSA advertising router in addition to the LSA type and
ID in the places where that information is necessary to uniquely
identify the LSA in the LSDB.
This is useful, for example, to know exactly which LSA has changed
when the router is exiting from the GR helper mode when a topology
change was detected.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
The debuild command fails when we are doing source package only build
because it expects the arch-dependent .changes file to be present. Thus
in the instructions we switch to using dpkg-buildpackage directly and
add a note about using debuild in more complicated scenarios.
Signed-off-by: Ondřej Surý <ondrej@sury.org>
In the CI, it's better to build the source package only once and then
instead of checking out the whole repository, only distribute the source
packages to the individual jobs.
Signed-off-by: Ondřej Surý <ondrej@sury.org>
The Debian autopkgtest would fail with new PAM introduced in Debian bullseye.
Add a little loop to wait a little longer for the changes to propagate.
Signed-off-by: Ondřej Surý <ondrej@sury.org>
Harmonize the code of functions ospf6_asbr_redistribute_disable and
ospf6_asbr_redistribute_reset.
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
The ospf6 router-id is provided by order of preference by:
ospf6d itself if the "ospf6 router-id X.X.X.X" command is set.
- zebra. If the "ip router-id X.X.X.X" zebra command is set, the
configured IP is provided as the ID or alternatively the highest
loopback IPv4 address or else the highest interface IPv4 address.
The running ospf6 router-id is stored in ospf6->router-id.
ospf6->router-id can change in the following conditions:
- A configuration change provides a new router-id value according to
the above rules. ospf6->router-id is updated to the new value if
there is no adjacency in FULL state. Otherwise, the ospf6d process
must be restarted to take the new router-id into account.
- On startup of both zebra and ospf6d, if ospf6d has not yet received a
valid router-id, ospf6d->router-id is set to 0 (i.e. 0.0.0.0). Then,
zebra notifies ospf6d that the router-id is available.
At ospf6->router-id, the current behavior of ospf6d is the following:
- The self generated LSAs that refer to the previous router-id as the
advertising router are kept.
- Self generated LSAs are created with router-id value.
- LSAs from the redistribution that refer to the previous router-id are
kept and no new redistribution LSAs are created.
As a consequence, the routers in the ospf6 areas will get incorrect
LSAs and might not be able to install prefixes of those LSAs into their
RIB.
This fix solves this issue by resetting the areas and the redistribution
when ospf6->router-id updated.
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
ospf6_router_id_update function is used by ospf6_router_id_update_zebra
to update the running the ospf6 router-id.
This patches makes the functions to (un)configure ospf6 router-id use
the same function as ospf6_router_id_update_zebra.
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
---
When a router-id change is notified by zebra to ospf6d, we only take
into account the change if no adjacencies are in Full state.
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
