Avoid undocumented topotest dependency on installing en_US locale.
With this change dependency is removed.
Signed-off-by: Christian Hopps <chopps@labn.net>
Add a test for the infinite recursion case fixed
with 0c4dbb5f8fe8fb188fa0e0aa8ce04764e893b79b
See that commit for details of the problem. This test uses a simpler
version of the repro found there as the test.
Signed-off-by: Stephen Worley <sworley@nvidia.com>
In test_converge_protocols() use sed to match the "show ip(v6) route"
header and strip it, rather than using tail which requires hardcoding
the expected length of the header (which is subject to change).
Signed-off-by: Duncan Eastoe <duncan.eastoe@att.com>
Add the ability for our topotests to take advantage of pytest `mark`ing.
This effectively allows you to tell pytest to run against certain sets
of tests. For a demonstration purpose I've added in marks for:
babel
eigrp
ldp
ospf
pim
rip
And setup tests to run against those tests that only test those protocols.
You can run against eigrp tests by running `pytest -k eigrp`
Other combinations are also available based upon simple boolean logic.
Just read the pytest.mark documentation.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
The `show ip nht` and `show ipv6 nht` commands were broken.
This is because recent code commit: 0154d8ce45
assumed that p must not be NULL and this is not the case.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
For each afi/safi of 'show bgp summary', display the peer description
each time needed. This information is useful, for instance in the case
of a device connected with multiple peers.
The topotest all_protocol_startup is changed accordingly.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Make sure the all-protocols test_isis_interfaces testcase uses
a regex substitution that includes all the hex characters.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
Modify bgpd.conf in all easily accessible topotests to use 3 10
as their timers du jour. This will allow the tests to converge
faster.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
When you make a change to a route-map or a prefix-list it depends on, note
that the route-map needs to be reprocessed for the change.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
`sharpd` doesn't handle any route map commands and neither should show
up in route map commands. This makes the CI pass again after not sending
route map commands to it again.
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
There exists the possiblity that the hello timer printed would
show a time to expiration in this format:
Hello due in 350 usecs
The tests are looking for:
Hello due in 5.430s
Just notice that we may have gotten usecs and act accordingly
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Just a simple setup for pbr to prove it starts. Once the json
code for pbr gets in we can add more.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Modify the import-check command to require the underlying prefix
to exist in the rib. General consensus is that this is the correct
behavior.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Add some more NHG topotests using connected, recursive, duplicate
and higher ecmp nexthops as well as route maps.
Signed-off-by: Stephen Worley <sworley@cumulusnetworks.com>
Add a couple more tests to static route installation
Do some very very basic work to make sure that they are working
the way we want.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
"sort" as used in all-protocol-startup used sort which causes
different sort order based on locale settings. Specify the
correct one to make output matching our expected result
Signed-off-by: Martin Winter <mwinter@opensourcerouting.org>
annie# show bgp ipv4 uni summ
BGP router identifier 192.168.201.136, local AS number 64539 vrf-id 0
BGP table version 22458946
RIB entries 1458006, using 178 MiB of memory
Peers 4, using 68 KiB of memory
Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd
45.33.5.119 4 0 0 0 0 0 0 never Active
65.19.134.122 4 15096 4611832 108292 0 0 0 6d22h55m 800670
107.13.46.23 4 0 0 0 0 0 0 never Connect
robot(192.168.201.139) 4 64540 11159975 11365599 0 0 0 05w2d05h Connect
Total number of neighbors 4
On very busy systems The column output for MsgRcvd and MsgSent can quickly move past 7 columns.
Add a couple more to allow for even display.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Add a very basic nexthop group functionality test.
This test creates a 2-way ecmp group and installs a route
with it using sharpd. Then we check to see that the nexthop
groups are marked valid/installed in zebra.
Signed-off-by: Stephen Worley <sworley@cumulusnetworks.com>
Add a couple of test cases to ensure that admin distance of
255 actually causes the route to be accepted by zebra but
not installed into the linux kernel.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Add a bit of code to test different spelling of Null0 routes.
This was broken at some point in the past and with recent
changes is working again, but it would be nice to
know when this breaks again.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
When we are ready to install a route, we were treating
blackhole routes as something that should be nexthop tracked
which does not work as well as one would expect.
Additionally add some test code to show that this actually
fixes this issue.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Different versions of linux are assigned different interface
ifindexes. Mask that cabbage out.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
The "show bgp ipv6 summary" output displays incorrect number of peers count.
sonic# show bgp ipv6 summary
IPv6 Unicast Summary:
BGP router identifier 10.1.0.1, local AS number 65100 vrf-id 0
BGP table version 0
RIB entries 0, using 0 bytes of memory
Peers 5, using 103 KiB of memory
Peer groups 1, using 64 bytes of memory
Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd
2003::1 4 65099 0 0 0 0 0 never Active
2088::1 4 65100 0 0 0 0 0 never Active
3021::2 4 65100 0 0 0 0 0 never Active
Total number of neighbors 3
sonic#
In the above output, the peers count displays as 5 but the actual peer count is 3, i.e.. 3 neighbors are activated in ipv6 unicast address family.
Displayed peer count (5) is the number of the neighbors activated in a BGP instance.
Fix : Now the peers count displays the number of neighbors activated per afi/safi.
After Fix:
sonic# show bgp ipv6 summary
IPv6 Unicast Summary:
BGP router identifier 10.1.0.1, local AS number 65100 vrf-id 0
BGP table version 0
RIB entries 0, using 0 bytes of memory
Peers 3, using 62 KiB of memory
Peer groups 1, using 64 bytes of memory
Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd
2003::1 4 65099 0 0 0 0 0 never Active
2088::1 4 65100 0 0 0 0 0 never Active
3021::2 4 65100 0 0 0 0 0 never Active
Total number of neighbors 3
sonic#
Signed-off-by: Akhilesh Samineni <akhilesh.samineni@broadcom.com>
This code just ensures that v4 and v6 routes are as expected
in the rib. While this test addition is not that complicated it would
have caught some issues while I was attempting to handle the
switchover to a different style of rib processing.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
