Problem reported that route-maps applied to "ip protocol table bgp"
would not be invoked if the ip protocol table command was issued
after the bgp prefixes were installed. Found that a recent change
improving how often nexthop_active_update runs missed causing this
filtering to be applied. This fix resolves that issue as well as
a couple of other places that were problematic with the recent
change.
Signed-off-by: Don Slice <dslice@cumulusnetworks.com>
Due to recent modification in northbound API, replace
yang_dnode_get_entry() call by nb_running_get_entry() call.
Signed-off-by: Olivier Dugeon <olivier.dugeon@orange.com>
Problem reported that if a bgp neighbor had a bfd timer change
made in frr.conf and systemctl reload frr performed, the neighbor
with the timer changed bounced. If the change is made in vtysh
by just adding the new timer values, no peer bounce occurs. This
fix skips the delete part of the delete/add process in frr-reload
so the peers stay up.
Signed-off-by: Don Slice <dslice@cumulusnetworks.com>
RFC 5881 Section 4 tells us that the BFD source port must be between
49152 and 65535 inclusive.
Spotted by Lucian Cristian.
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
Solve issue #4032
- Change MPLS-TE from global to per Area
- Add new mpls_te_area structure to area in replacement of global variable
isisMPLS_TE
- Move mpls-te from global to instance in frr-isisd.yang
- Change code in isis_te.c, isis_northbound.c, isis_cli.c, isis_pdu.c,
isis_lsp.c and isis_zebra.c accordingly
Signed-off-by: Olivier Dugeon <olivier.dugeon@orange.com>
Ralph has kindly granted us GPLv2+ license to use this documentation,
and requests that we keep a reference to his name. Add these facts to
the documentation.
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
the json code has not been updated since a variety of new flags have
been added to the code base. Add those flags in so we can tell
what is going on sometimes.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
The PIM-EVPN doc was not rendering very well on the
website. So Update documentation to allow it to render
better.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Add the ability to select on a S or G for a `show ip mroute`
command.
show ip mroute 225.1.1.111
show ip mroute 4.5.6.7 225.1.1.111
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Always when creating a new S,G state look at all possible ifchannels
to decide what the mroute should be.
The bug that this is fixing is this:
Suppose two incoming `*,G` joins on swp1, and swp2.
Now suppose that one of those ifchannel `*,G` sends a `*,G S,G RPT Prune`.
We were creating the S,G upstream state as we should but we were
only looking at the S,G ifchannel to decide the S,G mroute we would
be creating. As such what we need to do is to look over the associated
*,G ifchannels and allow us to associate correct oil needed.
Ticket: CM-24732
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
* Reflow to 80 columns
* Improve markup
* Add --apiserver option to example ospfd invocations
* Add note on requirement of this option to use api server
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
Start using the dataplane for interface-address programming,
on netlink platforms. Other platforms just stubbed at this
point.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
