We've run across an issue where the local connected
ip address is not being removed in some error condition.
During trackdown it was noticed that we cannot look
at this table for views/vrf's. While we don't have the
bug tracked down yet this will help us figure it out.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Problem reported with output of the command "show bgp vrf all
neighbor x.x.x.x" not limiting the output to that peer in any vrf.
This fix corrects the logic to display by neighbor
(ipv4/ipv6/interface) in any vrf.
Ticket: CM-17377
Signed-off-by: Don Slice <dslice@cumulusnetworks.com>
The bestpath multipath-relax setting was added to the output of
"show ip bgp neighbor json" several months ago but this is not
the correct place to display that information and this fix removes
it from there. The multipath-relax setting was also added
to the output of "show ip bgp sum json" which is fine.
Signed-off-by: Don Slice <dslice@cumulusnetworks.com>
Adds ability to specify that peers should be administratively shutdown
when first configured.
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
Remove the ability to attempt to configure a couple of options on
directly connected neighbors that don't make sense for them, as well as
the soft error handling code.
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
If we have configured neighbor 1.1.1.1 for an afi/safi but they have not
activated that afi/safi with us then display "NoNeg" in the state column
of the summary output. This is to make troubleshooting afi/safi
easier.
Signed-off-by: Daniel Walton <dwalton@cumulusnetworks.com>
The bgpTimerUp value was incorrectly named, add
a correct name bgpTimerUpMsec and add some
code to allow for deprecation.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
For some reason bgp is calculating the peer uptime
in miliseconds incorrectly. Additionally we have
the peer_uptime function call that should be doing this!
But since we've choosen different names for the json output
we cannot fix it at this point.
uptime contains the number of seconds of uptime here. Just
multiply by 1k and display that( as peer_uptime does )
Fixes: #1585
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Was using 0 as a sentinel value, so user couldn't configure 0 as the
value of the coalesce timer.
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
BGP VRF can be created/deleted either via config or via l3vni add/del.
We need to handle various sequences.
1. If user config is presented, an l3vni del should not delete the vrf instance
2. do not write bgp config in show running for auto created vrf
2. If l3vni present, disallow the cli for deleting bgp vrf instance
3. If l3vni is added and vrf config is present set the flags properly
4. if bgp vrf is configured unset the AUTO flag
Ticket: CM-18630
Review: CCR-6906
Testing: Manual
Signed-off-by: Mitesh Kanjariya <mitesh@cumulusnetworks.com>
Since coalesce time is now heuristically adjusted based on peer count,
we need to separate out specific configuration by the user from the
current value. Behavior established is to not adjust if the user has a
value set.
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
bgpd supports setting a write-quanta that serves as a hint on how many
packets to write per I/O cycle. Now that input is buffered, it makes
sense to add the equivalent parameter for how many packets are processed
per cycle. This is *not* how many packets are read off the wire per I/O
cycle; rather it is how many packets are processed from the input buffer
in a given cycle after having been read off the wire and sanitized.
Since these values must be used from multiple threads, they have also
been made atomic.
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
* Move and modify all network input related code to bgp_io.c
* Add a real input buffer to `struct peer`
* Move connection initialization to its own thread.c task instead of
piggybacking off of bgp_read()
* Tons of little fixups
Primary changes are in bgp_packet.[ch], bgp_io.[ch], bgp_fsm.[ch].
Changes made elsewhere are almost exclusively refactoring peer->ibuf to
peer->curr since peer->ibuf is now the true FIFO packet input buffer
while peer->curr represents the packet currently being processed by the
main pthread.
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
* Remove t_write
* Remove t_keepalive
These have been replaced by pthreads and are no longer needed. Since
some code looks at these values to determine if the threads are
scheduled, also add a new bitfield to store the same information.
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
Building a communities json object every time is
both expensive and memory wasteful. Modify
code to only build the json object when needed.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Fixes a bug whereby all peer-groups would be shown even when a
particular peer-group was specified for display.
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
Problem reported that we weren't adjusting the keepalive timer
correctly when we negotiated a lower hold time learned from a
peer. While working on this, found we didn't do inheritance
correctly at all. This fix solves the first problem and also
ensures that the timers are configured correctly based on this
priority order - peer defined > peer-group defined > global config.
This fix also displays the timers as "configured" regardless of
which of the three locations above is used.
Ticket: CM-18408
Signed-off-by: Don Slice <dslice@cumulusnetworks.com>
Reviewed-by: CCR-6807
Testing-performed: Manual testing successful, fix tested by
submitter, bgp-smoke completed successfully
When retrieving information about neighbors or summary in json
add some information about what bestPath particulars we have for
this bgp session.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
