Previously we just raised an error for the test file with possibly all tests
passing. Now we fail any test that produces new backtraces or cores. This
just works a lot better with analysis and even CI.
Also be less verbose to the console after failure runs, just show error
level and above logs. The log files still capture all levels (DEBUG).
Signed-off-by: Christian Hopps <chopps@labn.net>
There's a workaround in the code from a bug from back in 2004, it ends
and re-enters config mode anytime an `exit` is done from a level below
the top-level config node (e.g., from a `router isis` node). We need to
re-enter config mode with or without a lock according to how we actually
entered it to begin with.
fixes#13920
Signed-off-by: Christian Hopps <chopps@labn.net>
The lock/unlocks are being done short-circuit so they are never pending;
however, the handling of the unlock notification was always resuming the command
if pending was set. In all cases pending is set for another command. For example
implicit commit locks then when notified its done unlocks which was clearing the
set-config pending flag and resuming that command incorrectly.
Signed-off-by: Christian Hopps <chopps@labn.net>
Currently, "on-match (next|goto)" only works if already present in a
route-map entry when the route-map is applied to the routes. However, if
the command is added to an existing route-map entry, the route-map is
not reapplied to the routes in order to accommodate the changes. And
service restart is needed. The problem is that setting the command
doesn't signal about the change to the listener (i.e. to a routing
daemon).
With this fix, signal to the listener about addition of "on-match
(next|goto)" to a route-map entry.
Signed-off-by: Alexander Chernavin <achernavin@netgate.com>
`bnc->ifindex` should not be with 0 ( IFINDEX_INTERNAL ), so we can ignore
the wrong interface to make it safe.
Signed-off-by: anlan_cs <vic.lan@pica8.com>
Currently the vrf change procedure for the deleted interface is after
its deletion, it causes problem for upper daemons.
Here is the problem of `bgp`:
After deletion of one **irrelevant** interface in the same vrf, its
`ifindex` is set to 0. And then, the vrf change procedure will send
"ZEBRA_INTERFACE_DOWN" to `bgpd`.
Normally, `bgp_nht_ifp_table_handle()` should igore this message for
no correlation. However, it wrongly matched `ifindex` of 0, and removed
the related routes for the down `bnc`.
Adjust the location of the vrf change procedure to fix this issue.
Signed-off-by: anlan_cs <vic.lan@pica8.com>
Make the ospf6_lsa_unlock take the same parameters
that the ospf_lsa_unlock does to make it consistent
and to also ensure that no-one can make the mistake
of getting the pointer cleared up.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Adjust one debug info, separate the ip address from it. Just like it is processed
in `redistribute_update()`.
Before:
```
34:1375.75.75.75/32: Redist del: re 0x55c1112067e0 (0:static), new re 0x55c1112de7c0 (0:static)
```
After:
```
(34:13):75.75.75.75/32: Redist del: re 0x55c1112067e0 (0:static), new re 0x55c1112de7c0 (0:static)
```
Signed-off-by: anlan_cs <vic.lan@pica8.com>
Add a test-case to the NHRP test that installs routes over the
NHRP tunnel endpoint routes. This confirms that zebra will use
NHRP routes when validating incoming routes from other daemons
(sharpd in this test).
Signed-off-by: Mark Stapp <mjs@labn.net>
Add a config option so that sharpd can install routes without
the ALLOW_RECURSION flag, matching IGP behavior.
The default remains 'recursion'.
Signed-off-by: Mark Stapp <mjs@labn.net>
Treat NHRP-installed routes as valid, as if they were
CONNECTED routes, when checking candidate routes'
nexthops for validity. This allows use of NHRP by an
IGP, for example, that doesn't normally want recursive
nexthop resolution.
Signed-off-by: Mark Stapp <mjs@labn.net>
