Useful to have it for datacenter profile only, disabled for traditional.
If the peer is not established or established, but has no description set,
we will show the FRR version instead, which is kinda handy to have instead of
nothing.
Signed-off-by: Donatas Abraitis <donatas@opensourcerouting.org>
Previously we just raised an error for the test file with possibly all tests
passing. Now we fail any test that produces new backtraces or cores. This
just works a lot better with analysis and even CI.
Also be less verbose to the console after failure runs, just show error
level and above logs. The log files still capture all levels (DEBUG).
Signed-off-by: Christian Hopps <chopps@labn.net>
The runtime path for grpc.so has been changed for test_grpc.cpp
and also there were couple of definitions which are duplicate,
hence renamed them.
Signed-off-by: Rajesh Gangam <rajeshgangam@gmail.com>
Currently, "on-match (next|goto)" only works if already present in a
route-map entry when the route-map is applied to the routes. However, if
the command is added to an existing route-map entry, the route-map is
not reapplied to the routes in order to accommodate the changes. And
service restart is needed. The problem is that setting the command
doesn't signal about the change to the listener (i.e. to a routing
daemon).
With this fix, signal to the listener about addition of "on-match
(next|goto)" to a route-map entry.
Signed-off-by: Alexander Chernavin <achernavin@netgate.com>
Make the ospf6_lsa_unlock take the same parameters
that the ospf_lsa_unlock does to make it consistent
and to also ensure that no-one can make the mistake
of getting the pointer cleared up.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Test BMP messages logging.
Configure the BMP monitoring policy, add and withdraw IPv4/v6 prefixes.
Check if the received messages coincide with the monitored router BGP
session activity.
Signed-off-by: Farid Mihoub <farid.mihoub@6wind.com>
Add a test-case to the NHRP test that installs routes over the
NHRP tunnel endpoint routes. This confirms that zebra will use
NHRP routes when validating incoming routes from other daemons
(sharpd in this test).
Signed-off-by: Mark Stapp <mjs@labn.net>
The changes allow the test to correctly pass in case the connection
between two peers is be established in less than 0.5 seconds after the
delayopen timer expires.
Signed-off-by: David Schweizer <dschweizer@opensourcerouting.org>
Attempt to set the hold time in the bgp flowspec exabgp
config. In addition it was noticed that upstream bgp_flowspec
tests are still not negotiating peering within the time frame
specified. This is because the first tcp packet is missed
and no keepalive/hold time are negotiated and exabgp will
not attempt a reconnect for quite some time. Make this
test slower when things go south.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
The isis_tilfa_topo1 test is failing because insufficient time was
given for isis to converge on the system under system load. Extend
the time and decrease the hello-interval timers to give it more
of a chance to converge.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
The test is failing because it assumes a json key
is always present when it is not. Test for it
before having the test fail.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
I have a local test run where the sharp route-map usage
was being checked for 5 seconds. I saw usages going up
for each 1 second check and the 5th one was at 497 out
of 500. Looks like the system was really loaded. Let's
give it more time to coalesce under heavy load.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
There are parts of our daemons that upon certain types
of errors that a zlog_backtrace is auto-generated.
It is desirable for this to be caught and have the
test auto-failed.
Issue: #13787
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
The bgp_vpnv6_per_nexthop_label tests only check to see if the mpls labels
are installed one time. Test runs show that all but one label is installed.
More than likely the test has asked for data while zebra is still installing
it. the mpls_label_check functions must check this result multiple times as
that system may be under heavy load.
A loop is introduced in order to let zebra check the mpls table.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Check `show ip route` for specific kernel routes after
the interface as their nexthop changes vrf.
After moving interface's vrf, there should be no kernel
route in old vrf.
Signed-off-by: anlan_cs <vic.lan@pica8.com>
There is no route-map set action to replace any ASN,
or a part of an ASN, with a configured ASN.
The current commit adds a new command to use a configured
ASN as replacement, instead of using the local as number.
> set as-path replace any 65500
Update the 'bgp_set_aspath_replace' test.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Add support for "[no] ip ospf capbility opaque" at the interface
level with the default being capability opaque enabled. The command
"no ip ospf capability opaque" will disable opaque LSA database
exchange and flooding on the interface. A change in configuration
will result in the interface being flapped to update our options
for neighbors but no attempt will be made to purge existing LSAs
as in dense topologies, these may received by neighbors through
different interfaces.
Topotests are added to test both the configuration and the LSA
opaque flooding suppression.
Signed-off-by: Acee <aceelindem@gmail.com>
