There is no support for option 8, as per RFC7854.
Add the 64 bit counter in the peer structure.
Add the missing per peer statistic.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Some wireshark versions can not decode the experimental
bmp stat code. This may also be the case for some collectors.
Add a vty command to be able to disable bmp to sending
those values.
> [no] bmp stat send-experimental
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
There is no support for option 7, as per RFC7854.
Add the 64 bit counter in the peer structure.
Add the 64 bit bmp value write api.
Add the missing per peer statistic.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
ietf-key-chain depends on ietf-netconf-acm, and lib/ code sets up the
former, so ietf-netconf-acm needs to be embedded in the libfrr too.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Add the support for adding DX6 behavior into netlink layer of zebra.
Add the necessary test in sharpd.
> ubuntu2204# sharp install seg6local-routes 1:1::1:2 nexthop-seg6local loop1 End_DX6 4:4::4:6 1
> ubuntu2204# do show ipv6 route
> [..]
> D>* 1:1::1:2/128 [150/0] is directly connected, loop1, seg6local End.DX6 nh6 4:4::4:6, weight 1, 00:00:03
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
use the new recommendation from cmake:
--install-prefix <directory>
New in version 3.21.
Specify the installation directory, used by the
CMAKE_INSTALL_PREFIX variable. Must be an
absolute path.
reminder: the default path is /usr/local instead of /usr
Signed-off-by: Vincent Jardin <vjardin@free.fr>
use the new recommendation from cmake:
--install-prefix <directory>
New in version 3.21.
Specify the installation directory, used by the
CMAKE_INSTALL_PREFIX variable. Must be an
absolute path.
reminder: the default path is /usr/local instead of /usr
Signed-off-by: Vincent Jardin <vjardin@free.fr>
use the new recommendation from cmake:
--install-prefix <directory>
New in version 3.21.
Specify the installation directory, used by the
CMAKE_INSTALL_PREFIX variable. Must be an
absolute path.
reminder: the default path is /usr/local instead of /usr
Signed-off-by: Vincent Jardin <vjardin@free.fr>
no form of 'ip pm msdp peer <> source <>' does not
accept source argument. Stip the 'source <>' part from
config line being deleted via frr-reload.
Ticket: #3874971
Testing:
Config:
vrf blue
ip msdp peer 1.1.1.1 source 1.1.1.1
frr-reload failure log:
2024-04-23 02:08:32,501 INFO: Failed to execute vrf blue no ip
msdp peer 1.1.1.1 source 1.1.1.1 exit
2024-04-23 02:08:32,501 ERROR: "vrf blue -- no ip msdp peer 1.1.1.1
source 1.1.1.1 -- exit" we failed to remove this command
2024-04-23 02:08:32,501 ERROR: % Unknown command: no ip msdp peer
1.1.1.1 source 1.1.1.1
Signed-off-by: Chirag Shah <chirag@nvidia.com>
When no ip pim is performed subsequent pim related
configs under the interface also implicitly deleted.
The previous fix was attempting to remove from the same
list which was being integrated.
First collect the lines to remove in separate list
then at the end remove from the original lines_to_del.
commit 623af04e1c does not work properly if tries to delete
an entry from existing list which is being walked on.
Ticket: #3869779
Testing done:
frr.conf:
no interface config
running-config:
--------------
interface swp1
ip pim
ip pim active-active
ip pim allow-rp rp-list sample
ip pim bfd
ip pim use-source 1.1.1.1
ip multicast boundary oil test
exit
frr-reload log pointing only no ip pim config
is removed under interface:
2024-04-18 18:44:37,202 INFO: "frr defaults datacenter" cannot be removed
2024-04-18 18:44:37,202 INFO: "service integrated-vtysh-config" cannot be removed
2024-04-18 18:44:37,504 INFO: Executed "interface swp1 no ip pim exit"
2024-04-18 18:44:37,505 INFO: /var/run/frr/reload-YHS51E.txt content
Signed-off-by: Chirag Shah <chirag@nvidia.com>
When testing SNMP service on FRR, the following error message may
appear on some distros.
> # snmpwalk -v2c -c public .1.3.6 1.1.1.1 <OID>
> Bad operator (INTEGER): At line 73 in /usr/share/snmp/mibs/ietf/SNMPv2-PDU
> [..then result ..]
>
The error message is due to the /etc/snmp/snmp.conf file. By default, this
file is used by both snmp server and client side. The net-snmp MIB parsing
routing loads MIBS, to bind oids with the naming scheme used by the MIBS.
> # cat /etc/frr/snmp.conf
> [snmp]
> mibs +ALL
>
A potential fix would consist in modifying the SNMPv2-PDU.mib file: the
problem is known on ubuntu distros, as the snmp-mibs-downloader package
has not updated the SNMPv2-PDU.mib file.
The choice is done to not modify the original distro where the test is run
on. Fix the topotests by ignoring the 'SNMPv2-PDU line 73" error message, and
keep the other error messages that may happen, for instance, when an
unknown oid name value is requested.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
