Add the support of Extended Admin-Group (RFC7308) to the zebra interface
link-params Traffic-Engineering context.
Extended admin-groups can be configured with the affinity-map:
> affinity-map blue bit-position 221
> int eth-rt1
> link-params
> affinity blue
> exit-link-params
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
RFC7471 and RFC8570 have defined the Extended Traffic Engineering
metrics that are carried within TLV of 32 bits data length. Extended
metrics, excepting bandwidth ones, use the following format:
> 0 1 2 3
> 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
> +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
> | Type | Length |
> +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
> |A| RESERVED | Value |
> +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Data contains a flag/reserved of 8 bits and a 24 bits value.
The TE_EXT_MASK mask macro extracts a 28 bits value from a 32 bits
variable instead of 24 bits. It works in most of the case because
RESERVED bits are generally set to 0.
Fix the TE_EXT_MASK mask.
Fixes: 16f1b9ee29 ("Update Traffic Engineering Support for OSPFD")
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
Add a function to find the VRF or the loopback interface: the loopback
interface for the default VRF and the VRF master interface otherwise.
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
Add a function to find the VRF or the loopback interface: the loopback
interface for the default VRF and the VRF master interface otherwise.
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
When enabling the interface link-params, a default bandwidth is assigned
to the Max, Reservable and Unreserved Bandwidth variables. If the
bandwidth is set at in the interface context, this value is used.
Otherwise, a default bandwidth value of 10 Gbps is set.
Revert the default value to 10 Mbps as it was intended in the initial
commit. 10 Mbps is a low value so that the link will not be prioritized
when computing the paths.
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
A given interface has no enabled link-params context. If a link-params
configuration command fails, the link-params is wrongly enabled:
> r4(config-link-params)# no enable
> r4(config-link-params)# delay
> (0-16777215) Average delay in micro-second as decimal (0...16777215)
> r4(config-link-params)# delay 50 min 300 max 500
> Average delay should be comprise between Min (300) and Max (500) delay
> r4(config-link-params)# do sh run zebra
> (...)
> interface eth-rt1
> link-params
> enable
> exit-link-params
link-params are enabled if and only if the interface structure has a
valid link_params pointer. Before checking the command validity,
if_link_params_get() is called to retrieve the link-params pointer.
However, this function initializes the pointer if it is NULL.
Only use if_link_params_get() to retrieve the pointer to avoid
confusion. In command setting functions, initialize the link_params
pointer if needed only after the validation of the command.
Fixes: 16f1b9e ("Update Traffic Engineering Support for OSPFD")
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
VRF name should not be printed in the config since 574445ec. The update
was done for NB config output but I missed it for regular vty output.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
Since f60a1188 we store a pointer to the VRF in the interface structure.
There's no need anymore to store a separate vrf_id field.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
Most users of if_lookup_address_exact only cared about whether the
address is any local address. Split that off into a separate function.
For the users that actually need the ifp - which I'm about to add a few
of - change it to prefer returning interfaces that are UP.
(Function name changed due to slight change in behavior re. UP state, to
avoid possible bugs from this change.)
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
We should always treat the VRF interface as a loopback. Currently, this
is not the case, because in some old pre-VRF code we use if_is_loopback
instead of if_is_loopback_or_vrf. To avoid any future problems, the
proposal is to rename if_is_loopback_or_vrf to if_is_loopback and use it
everywhere. if_is_loopback is renamed to if_is_loopback_exact in case
it's ever needed, but currently it's not used anywhere.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
This function doesn't work correctly with netns VRF backend as the same
index may be used in multiple netns simultaneously. So let's hide it
from the public API to reduce temptation to use it instead of writing
the correct code.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
When writing the config from the NB-converted daemon, we must not rely
on the operational data. This commit changes the output of the interface
configuration to use only config data. As the code is the same for all
daemons, move it to the lib and remove all the duplicated code.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
It allows FRR to read the interface config even when the necessary VRFs
are not yet created and interfaces are in "wrong" VRFs. Currently, such
config is rejected.
For VRF-lite backend, we don't care at all about the VRF of the inactive
interface. When the interface is created in the OS and becomes active,
we always use its actual VRF instead of the configured one. So there's
no need to reject the config.
For netns backend, we may have multiple interfaces with the same name in
different VRFs. So we care about the VRF of inactive interfaces. And we
must allow to preconfigure the interface in a VRF even before it is
moved to the corresponding netns. From now on, we allow to create
multiple configs for the same interface name in different VRFs and
the necessary config is applied once the OS interface is moved to the
corresponding netns.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
This function doesn't work correctly with netns VRF backend as the same
ifname may be used in multiple netns simultaneously. So let's hide it
from the public API to reduce temptation to use it instead of writing
the correct code.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
The only difference in daemons' interface node definition is the config
write function. No need to define the node in every daemon, just pass
the callback as an argument to a library function and define the node
there.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
Track 'down' state of connected addresses with a new flag. We
may have multiple addresses on an interface that share a prefix;
in those cases, we need to determine when the first address
is valid, to install a connected route, and similarly detect
when the last address goes 'down', to remove the connected
route.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
Back when I put this together in 2015, ISO C11 was still reasonably new
and we couldn't require it just yet. Without ISO C11, there is no
"good" way (only bad hacks) to require a semicolon after a macro that
ends with a function definition. And if you added one anyway, you'd get
"spurious semicolon" warnings on some compilers...
With C11, `_Static_assert()` at the end of a macro will make it so that
the semicolon is properly required, consumed, and not warned about.
Consistently requiring semicolons after "file-level" macros matches
Linux kernel coding style and helps some editors against mis-syntax'ing
these macros.
Signed-off-by: David Lamparter <equinox@diac24.net>
Add if_vrf_lookup_by_index_next to get the next ifindex in a vrf
given the previous ifindex or 0 for the first.
Signed-off-by: Pat Ruddy <pat@voltanet.io>
If we have an interface configured in a daemon on shutdown
store the old ifindex value for retrieval on when it is
possibly recreated.
This is especially important for nexthop groups as that we
had at one point in time the ability to restore the
configuration but it was lost when we started deleting
all deleted interfaces. We need the nexthop group subsystem
to also mark that it has configured an interface.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Revert "zebra: support for macvlan interfaces"
This reverts commit bf69e212fd.
Revert "doc: add some documentation about bgp evpn netns support"
This reverts commit 89b97c33d7.
Revert "zebra: dynamically detect vxlan link interfaces in other netns"
This reverts commit de0ebb2540.
Revert "bgpd: sanity check when updating nexthop from bgp to zebra"
This reverts commit ee9633ed87.
Revert "lib, zebra: reuse and adapt ns_list walk functionality"
This reverts commit c4d466c830.
Revert "zebra: local mac entries populated in correct netnamespace"
This reverts commit 4042454891.
Revert "zebra: when parsing local entry against dad, retrieve config"
This reverts commit 3acc394bc5.
Revert "bgpd: evpn nexthop can be changed by default"
This reverts commit a2342a2412.
Revert "zebra: zvni_map_to_vlan() adaptation for all namespaces"
This reverts commit db81d18647.
Revert "zebra: add ns_id attribute to mac structure"
This reverts commit 388d5b438e.
Revert "zebra: bridge layer2 information records ns_id where bridge is"
This reverts commit b5b453a2d6.
Revert "zebra, lib: new API to get absolute netns val from relative netns val"
This reverts commit b6ebab34f6.
Revert "zebra, lib: store relative default ns id in each namespace"
This reverts commit 9d3555e06c.
Revert "zebra, lib: add an internal API to get relative default nsid in other ns"
This reverts commit 97c9e7533b.
Revert "zebra: map vxlan interface to bridge interface with correct ns id"
This reverts commit 7c990878f2.
Revert "zebra: fdb and neighbor table are read for all zns"
This reverts commit f8ed2c5420.
Revert "zebra: zvni_map_to_svi() adaptation for other network namespaces"
This reverts commit 2a9dccb647.
Revert "zebra: display interface slave type"
This reverts commit fc3141393a.
Revert "zebra: zvni_from_svi() adaptation for other network namespaces"
This reverts commit 6fe516bd4b.
Revert "zebra: importation of bgp evpn rt5 from vni with other netns"
This reverts commit 28254125d0.
Revert "lib, zebra: update interface name at netlink creation"
This reverts commit 1f7a68a2ff.
Signed-off-by: Pat Ruddy <pat@voltanet.io>
in the CLI we state that the bandwidth of a link is
in Megabits per second, but when converting it to
Bytes per second for TE purposes we were treating
it as Kilobits. Fix the conversion error.
Signed-off-by: Emanuele Di Pascale <emanuele@voltanet.io>
the interface name was not present in the hook in charge of updating the
interface context to the registered hook service. For that, update the
name before informing it.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Parameters should be const whenever possible to improve code
readability and remove the need to cast away the constness of
const arguments.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Having a fixed set of parameters for each northbound callback isn't a
good idea since it makes it difficult to add new parameters whenever
that becomes necessary, as several hundreds or thousands of existing
callbacks need to be updated accordingly.
To remediate this issue, this commit changes the signature of all
northbound callbacks to have a single parameter: a pointer to a
'nb_cb_x_args' structure (where x is different for each type
of callback). These structures encapsulate all real parameters
(both input and output) the callbacks need to have access to. And
adding a new parameter to a given callback is as simple as adding
a new field to the corresponding 'nb_cb_x_args' structure, without
needing to update any instance of that callback in any daemon.
This commit includes a .cocci semantic patch that can be used to
update old code to the new format automatically.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
This fixes a theoretical bug that could occur when trying to change an
ifindex on an interface to that of an existing interface. We would
remove the interface from the ifindex tree, and change the ifindex, but
when we tried to reinsert the interface, the insert would fail. It was
impossible to know if this failed due to the insertion / deletion macros
capturing the result value of the underlying BSD tree macros. So we
would effectively delete the interface.
Instead of failing on insert, we just check if the prospective ifindex
already exists and return -1 if it does.
Macros have been changed to statement expressions so the result can be
checked, and bubbled up.
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
Cleanup the interface creation apis to make it more
clear what they are doing.
Make it explicit that the creation via name/ifindex will
only add it to the appropriate list.
Signed-off-by: Stephen Worley <sworley@cumulusnetworks.com>
We were using the incorrect comparison function for the
ifindex-based rb tree. Luckily, we were using the correct one
in RB_GENERATE so I guess that overwrote what was declared in the
prototype?
Signed-off-by: Stephen Worley <sworley@cumulusnetworks.com>
For all the places we have a zclient->interface_up convert
them to use the interface ifp_up callback instead.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Switch the zclient->interface_add functionality to have everyone
use the interface create callback in lib/if.c
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Start the conversion to allow zapi interface callbacks to be
controlled like vrf creation/destruction/change callbacks.
This will allow us to consolidate control into the interface.c
instead of having each daemon read the stream and react accordingly.
This will hopefully reduce a bunch of cut-n-paste stuff
Create 4 new callback functions that will be controlled by
lib/if.c
create -> A upper level protocol receives an interface creation event
The ifp is brand spanking newly created in the system.
up -> A upper level protocol receives a interface up event
This means the interface is up and ready to go.
down -> A upper level protocol receives a interface down
destroy -> A upper level protocol receives a destroy event
This means to delete the pointers associated with it.
At this point this is just boilerplate setup for future commits.
There is no new functionality.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
When zebra gets a callback from the kernel that an interface has
actually been deleted *and* the end users has not configured
the interface, then allow for deletion of the interface from zebra.
This is especially important in a docker environment where containers
and their veth interfaces are treated as ephermeal. FRR can quickly
have an inordinate amount of interfaces sitting around that are
not in the kernel and we have no way to clean them up either.
My expectation is that this will cause a second order crashes
in upper level protocols, but I am not sure how to catch these
and fix them now ( suggestions welcome ). There are too many
use patterns and order based events that I cannot know for certain
that we are going to see any at all, until someone sees this problem
as a crash :( I do not recommend that this be put in the current
stabilization branch and allow this to soak in master for some time
first.
Testing:
sharpd@donna ~/frr4> sudo ip link add vethdj type veth peer name vethjd
sharpd@donna ~/frr4> sudo ip link add vethaa type veth peer name vethab
sharpd@donna ~/frr4> sudo vtysh -c "show int brief"
Interface Status VRF Addresses
--------- ------ --- ---------
dummy1 down default
enp0s3 up default 10.0.2.15/24
enp0s8 up default 192.168.209.2/24
enp0s9 up default 192.168.210.2/24
enp0s10 up default 192.168.212.4/24
lo up default 10.22.89.38/32
vethaa down default
vethab down default
vethdj down default
vethjd down default
virbr0 up default 192.168.122.1/24
virbr0-nic down default
sharpd@donna ~/frr4> sudo ip link set vethaa up
sharpd@donna ~/frr4> sudo ip link set vethab up
sharpd@donna ~/frr4> sudo ip link del vethdj
sharpd@donna ~/frr4> sudo vtysh -c "show int brief"
Interface Status VRF Addresses
--------- ------ --- ---------
dummy1 down default
enp0s3 up default 10.0.2.15/24
enp0s8 up default 192.168.209.2/24
enp0s9 up default 192.168.210.2/24
enp0s10 up default 192.168.212.4/24
lo up default 10.22.89.38/32
vethaa up default
vethab up default
virbr0 up default 192.168.122.1/24
virbr0-nic down default
sharpd@donna ~/frr4> sudo ip link del vethaa
sharpd@donna ~/frr4> sudo vtysh -c "show int brief"
Interface Status VRF Addresses
--------- ------ --- ---------
dummy1 down default
enp0s3 up default 10.0.2.15/24
enp0s8 up default 192.168.209.2/24
enp0s9 up default 192.168.210.2/24
enp0s10 up default 192.168.212.4/24
lo up default 10.22.89.38/32
virbr0 up default 192.168.122.1/24
virbr0-nic down default
sharpd@donna ~/frr4> sudo ip link add vethaa type veth peer name vethab
sharpd@donna ~/frr4> sudo vtysh -c "show int brief"
Interface Status VRF Addresses
--------- ------ --- ---------
dummy1 down default
enp0s3 up default 10.0.2.15/24
enp0s8 up default 192.168.209.2/24
enp0s9 up default 192.168.210.2/24
enp0s10 up default 192.168.212.4/24
lo up default 10.22.89.38/32
vethaa down default
vethab down default
virbr0 up default 192.168.122.1/24
virbr0-nic down default
sharpd@donna ~/frr4> sudo vtysh -c "show run"
Building configuration...
Current configuration:
!
frr version 7.2-dev
frr defaults datacenter
hostname donna.cumulusnetworks.com
log stdout
no ipv6 forwarding
!
ip route 192.168.3.0/24 192.168.209.1
ip route 192.168.4.0/24 blackhole
ip route 192.168.5.0/24 192.168.209.1
ip route 192.168.6.0/24 192.168.209.1
ip route 192.168.7.0/24 99.99.99.99 nexthop-vrf EVA
ip route 192.168.8.0/24 192.168.209.1
ip route 4.5.6.7/32 12.13.14.15
!
interface dummy1
ip address 12.13.14.15/32
!
interface vethaa
description FROO
!
line vty
!
end
sharpd@donna ~/frr4> sudo ip link del vethaa
sharpd@donna ~/frr4> sudo vtysh -c "show int brief"
Interface Status VRF Addresses
--------- ------ --- ---------
dummy1 down default
enp0s3 up default 10.0.2.15/24
enp0s8 up default 192.168.209.2/24
enp0s9 up default 192.168.210.2/24
enp0s10 up default 192.168.212.4/24
lo up default 10.22.89.38/32
vethaa down default
virbr0 up default 192.168.122.1/24
virbr0-nic down default
sharpd@donna ~/frr4> sudo vtysh -c "show run"
Building configuration...
Current configuration:
!
frr version 7.2-dev
frr defaults datacenter
hostname donna.cumulusnetworks.com
log stdout
no ipv6 forwarding
!
ip route 192.168.3.0/24 192.168.209.1
ip route 192.168.4.0/24 blackhole
ip route 192.168.5.0/24 192.168.209.1
ip route 192.168.6.0/24 192.168.209.1
ip route 192.168.7.0/24 99.99.99.99 nexthop-vrf EVA
ip route 192.168.8.0/24 192.168.209.1
ip route 4.5.6.7/32 12.13.14.15
!
interface dummy1
ip address 12.13.14.15/32
!
interface vethaa
description FROO
!
line vty
!
end
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
