Add a terse option to show bgp summary to shorten output.
Do not show the following information about the BGP
instances: the number of RIB entries, the table version and the used memory.
The "terse" option can be used in combination with the "remote-as", "neighbor",
"failed" and "established" filters, and with the "wide" option as well.
Before patch:
ubuntu# show bgp summary remote-as 123456
IPv4 Unicast Summary (VRF default):
BGP router identifier X.X.X.X, local AS number XXX vrf-id 0
BGP table version 0
RIB entries 3, using 552 bytes of memory
Peers 5, using 3635 KiB of memory
Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd PfxSnt Desc
10.200.200.2 4 123456 81432 4 0 56092 0 00:00:13 572106 0 N/A
Displayed neighbors 1
Total number of neighbors 4
IPv6 Unicast Summary (VRF default):
BGP router identifier X.X.X.X, local AS number XXX vrf-id 0
BGP table version 0
RIB entries 3, using 552 bytes of memory
Peers 5, using 3635 KiB of memory
Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd PfxSnt Desc
% No matching neighbor
Total number of neighbors 5
After patch:
ubuntu# show bgp summary remote-as 123456 terse
IPv4 Unicast Summary (VRF default):
BGP router identifier X.X.X.X, local AS number XXX vrf-id 0
Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd PfxSnt Desc
10.200.200.2 4 123456 81432 4 0 56092 0 00:00:13 572106 0 N/A
Displayed neighbors 1
Total number of neighbors 4
IPv6 Unicast Summary (VRF default):
BGP router identifier X.X.X.X, local AS number XXX vrf-id 1
% No matching neighbor
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
similarly to what was done for IS-IS in commit 01d43141, combine
the SRGB and SRLB commands for OSPF-SR, so that we can replace
overlapping ranges in one sweep change.
Also allow the range configuration to be stored before SR is enabled.
There is no reason why we should not - in fact that constraint meant
that we were always requesting the default label ranges regardless
of what we actually wanted to use.
Finally, update the topotests now that we do not need to refresh
the SRGB/SRLB/MSD after disabling SR. Note that the prefix-sid still
needs to be re-added.
Signed-off-by: Emanuele Di Pascale <emanuele@voltanet.io>
Modify VRF/view display in show bgp summary:
- to be more concise
- to display on which VRF/view no neighbor was found
Before patch:
ubuntu# show bgp vrf all summary
Instance default:
IPv4 Unicast Summary:
BGP router identifier XX.XX.XX.XX, local AS number XXXX vrf-id 0
(...)
IPv6 Unicast Summary:
Instance private:
IPv4 Unicast Summary:
ubuntu# show bgp vrf all ipv4 multicast summary
% No BGP neighbors found
% No BGP neighbors found
After patch:
ubuntu# show bgp vrf all summary
IPv4 Unicast Summary (VRF default):
BGP router identifier XX.XX.XX.XX, local AS number XXXX vrf-id 0
(...)
IPv6 Unicast Summary (VRF default):
(...)
IPv4 Unicast Summary (VRF private):
(...)
ubuntu# show bgp vrf all ipv4 multicast summary
% No BGP neighbors found in VRF default
% No BGP neighbors found in VRF private
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
"ip nht resolve-via-default" is currently placed in "Link Parameters
Commands" section. Add a separate section and missing IPv6 counterpart.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
Add ability to filter session on show bgp summary by neighbor or
remote AS:
ubuntu# show bgp summary ?
neighbor Show only the specified neighbor session
remote-as Show only the specified remote AS session
ubuntu# show bgp summary neighbor ?
A.B.C.D Neighbor to display information about
WORD Neighbor on BGP configured interface
X:X::X:X Neighbor to display information about
ubuntu# show bgp summary remote-as ?
(1-4294967295) AS number
external External (eBGP) AS sessions
internal Internal (iBGP) AS sessions
This patch includes the documentation and the topotest.
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
- As an example of pathd and igp (ospfd) config:
! igp ospfv2 snippet
interface eth0
ip ospf network point-to-point
!
router ospf$
mpls-te on
mpls-te export
...
!pathd snippet
segment-routing
traffic-eng
mpls-te on
mpls-te import ospfv2
segment-list sl-1
index 10 nai adjacency 10.1.2.11 10.1.2.1
index 20 nai adjacency 10.1.20.1 10.1.20.2
index 30 nai adjacency 10.2.5.2 10.2.5.5
!
policy color 5 endpoint 10.10.10.5
name five
binding-sid 5555
candidate-path preference 600 name cp51 explicit segment-list sl-1
candidate-path preference 500 name cp52-dyn dynamic
Signed-off-by: Javier Garcia <javier.garcia@voltanet.io>
Description:
Added a new show command("show ip zebra route dump") to dump all routes
with detailed information including nexthops,flags, status ..etc.
This helps for dubugging and added to support_bundle_command.conf.
Defined this command as a hidden command.
Signed-off-by: Rajesh Girada <rgirada@vmware.com>
Problem Statement:
=================
In scale setup BGP sessions start flapping.
RCA:
====
In virtualized environment there are multiple places where
MTU need to be set. If there are some places were MTU is not set
properly then there is chances that BGP packets get fragmented,
in scale setup this will lead to BGP session flap.
Fix:
====
A new tcp option is provided as part of this implementation,
which can be configured per neighbor and helps to set the TCP
max segment size. User need to derive the path MTU between the BGP
neighbors and set that value as part of tcp-mss setting.
1. CLI Configuration:
[no] neighbor <A.B.C.D|X:X::X:X|WORD> tcp-mss (1-65535)
2. Running config
frr# show running-config
router bgp 100
neighbor 198.51.100.2 tcp-mss 150 => new entry
neighbor 2001:DB8::2 tcp-mss 400 => new entry
3. Show command
frr# show bgp neighbors 198.51.100.2
BGP neighbor is 198.51.100.2, remote AS 100, local AS 100, internal link
Hostname: frr
Configured tcp-mss is 150, synced tcp-mss is 138 => new display
4. Show command json output
frr# show bgp neighbors 2001:DB8::2 json
{
"2001:DB8::2":{
"remoteAs":100,
"bgpTimerKeepAliveIntervalMsecs":60000,
"bgpTcpMssConfigured":400, => new entry
"bgpTcpMssSynced":388, => new entry
Risk:
=====
Low - This is a config driven feature and it sets the max segment
size for the TCP session between BGP peers.
Tests Executed:
===============
Have done manual testing with three router topology.
1. Executed basic config and un config scenarios
2. Verified if the config is updated in running config
during config and no config operation
3. Verified the show command output in both CLI format and
JSON format.
4. Verified if TCP SYN messages carry the max segment size
in their initial packets.
5. Verified the behaviour during clear bgp session.
6. done packet capture to see if the new segment size
takes effect.
Signed-off-by: Abhinay Ramesh <rabhinay@vmware.com>
Currently we have a "route-map optimization" command which is entered
from inside the route-map entry but actually applies to the whole
route-map. In addition, this command is not shown in the running-config
and not stored to the startup-config during "write".
Let's add a new command on the config node level to control this setting
and show it in the running-config to make possible to save it during
"write".
The old command is saved for the backward compatibility but hidden and
marked as deprecated.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
Most of these are many, many years out of date. All of them vary
randomly in quality. They show up by default in packages where they
aren't really useful now that we use integrated config. Remove them.
The useful ones have been moved to the docs.
Signed-off-by: Quentin Young <qlyoung@nvidia.com>
increase the maximum number of neighbors in a bgp group.
Set the maximum value to 50000 instead of 5000.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Add docs for commands to display BGP table per-RD.
Also update commands to mention flowspec, routes,
advertised-routes, and received-routes.
Signed-off-by: Trey Aspelund <taspelund@nvidia.com>
Description:
OSPF does not have an option to control the maximum multiple
equal cost paths to reach a destination/route(ECMP).
Currently, it is using the system specific max multiple paths.
But Somtimes, It requires to control the multiple paths from ospf.
This cli helps to configure the max number multiple paths in ospf.
Signed-off-by: Rajesh Girada <rgirada@vmware.com>
