Both the label manager and table manager zapi code send data requests via zapi
to zebra and then immediately listen for a response from zebra. The problem here
is of course that the listen part is throwing away any zapi command that is not
the one it is looking for.
ISIS/OSPF and PIM all have synchronous abilities via zapi, which they all
do through a special zapi connection to zebra. BGP needs to follow this model
as well. Additionally the new zclient_sync connection that should be created,
a once a second timer should wake up and read any data on the socket to
prevent problems too much data accumulating in the socket.
```
r3# sh bgp labelpool summary
Labelpool Summary
-----------------
Ledger: 3
InUse: 3
Requests: 0
LabelChunks: 1
Pending: 128
Reconnects: 1
r3# sh bgp labelpool inuse
Prefix Label
---------------------------
10.0.0.1/32 16
192.168.31.0/24 17
192.168.32.0/24 18
r3#
```
Signed-off-by: Donatas Abraitis <donatas@opensourcerouting.org>
The bgp_vpnv4_per_nexthop_label tests only check to see if the mpls labels
are installed one time. Test runs show that all but one label is installed.
More than likely the test has asked for data while zebra is still installing
it. the mpls_label_check functions must check this result multiple times as
that system may be under heavy load.
A loop is introduced in order to let zebra check the mpls table.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
This test has several issues:
A) The convergence function is spamming the show neighbor command until success,
if the neighbor never comes up the test will never finish. This adds unnecessary
load to an already loaded test system. Use run_and_expect to properly wait for
the neighbor relationship to come up.
B) The convergence function should not sleep for 1 second *After* the neighbor
is established
C) The _bgp_as_path() function fails if the prefix has not been received yet.
This looking for the prefix data should be within a run_and_expect() functionality.
Else a loaded test system will fail in this function because while we may be in
an established state, prefixes might not yet have been exchanged and there is no
point in failing the test without giving the system some time to actually converge.
Fix those points, similarly to what has been fixed in
bgp_local_as_private_remove test.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
According to RFC 7166, the sequence number should be treated as an
unsigned 64-bit value, although it is stored as two 32-bit values.
When incrementing it, the code caused the lower-order 32-bit value
to skip from 0xFFFFFFFE to 0. As a side effect, an error was never
produced if the full 64-bit sequence number wrapped.
Fixes: #13805
Signed-off-by: David Ward <david.ward@ll.mit.edu>
It is not possible to flush all the incoming as-path list
from a given BGP update.
Add a route-map set command to remove all as-paths
from a given AS path. Add the necessary tests.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Add more VRFs in bgp_vpnv4_noretain and test combinations of no-retain
/ retain and import / un-import.
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
Remove no retain in r2 and check that r2 VPN table remains the same
after r1 configuration changes.
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
Do not import r1 vrf1 to itself in order to check that r1 vrf1 prefixes
are only in VPN table because it is needed for advertising the prefixes
to other routers.
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
'{}' extra output may present JSON output from bgp_show_table_rd() when
no prefix are seen.
> {
> "vrfId": 0,
> "vrfName": "default",
> "tableVersion": 0,
> "routerId": "1.1.1.1",
> "defaultLocPrf": 100,
> "localAS": 65500,
> "routes": { "routeDistinguishers" : { "444:1" : { } } } }
> {}
Do not output '{}' when bgp_show_table() returns a valid JSON.
Tested without rd in config, bgp_show_table() returns nothing and the
JSON output is only '{}'
Fixes: 0224b3296c ("bgpd: Print empty JSON `{}` if no entries under `show bgp ipv4 vpn json`")
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
After some VRF imports are removed and "no bgp retain route-target all"
is set, prefixes that are not imported anymore remain in the BGP table.
Parse the BGP table and remove un-imported prefixes in such a case.
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
