Fixing compilation error in a switch statement case
Fixes :aa4786642c9a65c282d0fd5247a35b0f14fa1c3c
Signed-off-by: Rajasekar Raja <rajasekarr@nvidia.com>
When reloading the following configuration:
```
vrf red
rpki
rpki cache tcp 172.65.0.2 8282 preference 1
exit
exit-vrf
```
frr-reload.py does not properly enter the `rpki` context
within a `vrf`. Because of this, it fails to apply RPKI
configurations.
Signed-off-by: Jonathan Voss <jvoss@onvox.net>
When deactivating babel no router babel and later re-enabling it router babel the previous configuration is still in place.
Steps to reproduce:
Enable babel
Configure babel
Disable babel with "no router babel"
Verify config
Expected correct behavior: No config present
Signed-off-by: Yaroslav Kholod <y.kholod@vyos.io>
If Duplicate Address Detection action is freeze
(permanent or definite time means not warn only mode)
then locally duplicate detected MAC delete notification
is not require to inform,
instead ask BGP to sync previous remote MAC entry.
In freeze case local MAC event is not known to BGP,
instead BGP is pointing to remote VTEP for the MAC.
Ticket: #3652383
Issue: 3652383
Signed-off-by: Chirag Shah <chirag@nvidia.com>
Upon if_down, we don't reset the valid flag for dependents
and unset the INSTALLED flag.
So when its time for the NHG to be deleted (routes dereferenced),
zebra deletes it since refcnt goes to 0, but stale NHG remains in kernel.
Ticket :#4200788
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Signed-off-by: Rajasekar Raja <rajasekarr@nvidia.com>
When stopping and restarting BGP daemon part of the configuration
remains. It should be cleared.
Particulary those are address-family parametes, like: distance,
ead-es-frag, disable-ead-evi-rx, disable-ead-evi-tx.
Signed-off-by: Yaroslav Kholod <y.kholod@vyos.io>
The rpki current state was ignored when calling for the 'show bgp ipvX
detail' command. Handle the support for this, with json support too.
> "rpkiValidationState" : "valid",
> "rpkiValidationState" : "invalid",
> "rpkiValidationState" : "not used",
> "rpkiValidationState" : "not found",
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Signed-off-by: Dmytro Shytyi <dmytro.shytyi@6wind.com>
When reloading the following configuration:
```
segment-routing
srv6
formats
format usid-f3216
wide-local-id-block explicit start 100
exit
!
format uncompressed-f4024
exit
!
exit
!
exit
!
exit
```
frr-reload.py does not properly enter the `formats` context. Because of this,
it fails with an unknown command error when applying new or updating format
configuration.
Signed-off-by: Jonathan Voss <jvoss@onvox.net>
`srv6_static_route` is a pure staticd topotest. It does not have any
dependency on bgpd and sharpd.
Let's fix the pytestmark to include only staticd.
Signed-off-by: Carmine Scarpitta <cscarpit@cisco.com>
This test was not actually failing when the results didn't match. Fail
now. Also fix the tests that are now found to be failing incorrectly
(wrong expected result).
Signed-off-by: Christian Hopps <chopps@labn.net>
If we do `no neighbor PG enforce-first-as`, it wasn't working because the flag
was inherited incorrectly for the members of the peer-group.
Fixes: 322462920e ("bgpd: Enable enforce-first-as by default")
Closes: https://github.com/FRRouting/frr/issues/17702
Signed-off-by: Donatas Abraitis <donatas@opensourcerouting.org>
Compile error with `--disable-ripd`:
```
mgmtd/mgmt_be_adapter.c:86:5: error: "HAVE_RIPD" is not defined, evaluates to 0 [-Werror=undef]
86 | #if HAVE_RIPD
| ^~~~~~~~~
```
I have searched the code, there is only three places need to be fixed.
Signed-off-by: anlan_cs <anlan_cs@126.com>
The documentation should provide the valid range of SRv6 locator
node-len parameter, rather than the default value.
Signed-off-by: Carmine Scarpitta <cscarpit@cisco.com>
The documentation should provide the valid range of SRv6 locator
block-len parameter, rather than the default value.
Signed-off-by: Carmine Scarpitta <cscarpit@cisco.com>
Align the order of the SRv6 locator parameters with the actual implementation:
```
"prefix X:X::X:X/M$prefix [block-len (16-64)$block_bit_len] \
[node-len (16-64)$node_bit_len] [func-bits (0-64)$func_bit_len]"
```
Signed-off-by: Carmine Scarpitta <cscarpit@cisco.com>
