This replaces manual checks of the flag with a wrapper macro to convey
the meaning "is evpn enabled on this vrf?"
Signed-off-by: Tuetuopay <tuetuopay@me.com>
Sponsored-by: Scaleway
This makes the instance bearing the advertise-all-vni config option
register to zebra as the EVPN one, forwarding it the option.
Signed-off-by: Tuetuopay <tuetuopay@me.com>
Sponsored-by: Scaleway
Found that previous fix for this issue caused collatoral damage and
reverted that fix. This fix clears the vrf_bitmaps when the vrf is
disabled/deleted and then re-applies the redist config when the vrf
is re-enabled.
Ticket: CM-24231
Signed-off-by: Don Slice <dslice@cumulusnetworks.com>
In the case of EVPN symmetric routing, the tenant VRF is associated with
a VNI that is used for routing and commonly referred to as the L3 VNI or
VRF VNI. Corresponding to this VNI is a VLAN and its associated L3 (IP)
interface (SVI). Overlay next hops (i.e., next hops for routes in the
tenant VRF) are reachable over this interface. Howver, in the model that
is supported in the implementation and commonly deployed, there is no
explicit Overlay IP address associated with the next hop in the tenant
VRF; the underlay IP is used if (since) the forwarding plane requires
a next hop IP. Therefore, the next hop has to be explicit flagged as
onlink to cause any next hop reachability checks in the forwarding plane
to be skipped.
https://tools.ietf.org/html/draft-ietf-bess-evpn-prefix-advertisement
section 4.4 provides additional description of the above constructs.
Use existing mechanism to specify the nexthops as onlink when installing
these routes from bgpd to zebra and get rid of a special flag that was
introduced for EVPN-sourced routes. Also, use the onlink flag during next
hop validation in zebra and eliminate other special checks.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
In the case of EVPN symmetric routing, the tenant VRF is associated with
a VNI that is used for routing and commonly referred to as the L3 VNI or
VRF VNI. Corresponding to this VNI is a VLAN and its associated L3 (IP)
interface (SVI). Overlay next hops (i.e., next hops for routes in the
tenant VRF) are reachable over this interface.
https://tools.ietf.org/html/draft-ietf-bess-evpn-prefix-advertisement
section 4.4 provides additional description of the above constructs.
Use the L3 interface exchanged between zebra and bgp in route install.
This patch in conjunction with the earlier one helps to eliminate some
special code in zebra to derive the next hop's interface.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
In the case of EVPN symmetric routing, the tenant VRF is associated with
a VNI that is used for routing and commonly referred to as the L3 VNI or
VRF VNI. Corresponding to this VNI is a VLAN and its associated L3 (IP)
interface (SVI). Overlay next hops (i.e., next hops for routes in the
tenant VRF) are reachable over this interface.
https://tools.ietf.org/html/draft-ietf-bess-evpn-prefix-advertisement
section 4.4 provides additional description of the above constructs.
The implementation currently derives this L3 interface for EVPN tenant
routes using special code that looks at route flags. This patch
exchanges the L3 interface between zebra and bgpd as part of the L3-VNI
exchange in order to eliminate some this special code.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
A few code paths weren't handling the vpnv6 nexthop lenghts as
expected, which was leading to problems like imported vpnv6 routes
not being marked as valid when they should. Fix this.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Made changes and updated the routemap applied counter in the following flows.
1.Increment when route map attached to a list.
2.Decrement when route map removed / modified from a list.
3.Increment/decrement when route map create/delete callback triggered.
4.Besides ,This counter need not be updated when a route map is got updated.
i.e changing/adding a match value to the existing routemap.
In BGP , same update api called for all three add/delete/update operation .
But this counter have to be updated only for routemap addition.
Addressed this specific change by identifying the routemap operation based
on routemap pointer.
Signed-off-by: RajeshGirada <rgirada@vmware.com>
the list of iprules is displayed in the 'show bgp ipv4 flowspec detail'
The list of iprules is displayed, only if it is installed.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
two kind of rules are being set from bgp flowspec: ipset based rules,
and ip rule rules. default route rules may have a lower priority than
the other rules ( that do not support default rules). so, if an ipset
rule without fwmark is being requested, then priority is arbitrarily set
to 1. the other case, priority is set to 0.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
because ip rule creation is used to not only handle traffic marked by
fwmark; but also for conveying traffic with from/to rules, a check of
the creation must be done in the linked list of ip rules.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
now, ip rule can be created from two differnt ways; however a single
zebra API has been defined. so make it consistent by adding a parameter
to the bgp zebra layer. the function will handle the rest.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
When an inactive-neigh delete is rxed bgp will not have a local path to
remove (and re-run path selection). Instead it simply re-installs the
current best remote path if any.
Ticket: CM-23018
Testing Done: evpn-min
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
Duplicate address detection configuration clis
under bgp l2vpn evpn config mode.
- Enabled/Disable (global knob) for feature.
- Configure cli for duplicate detection action
freeze and freze until time (auto-recovery).
Signed-off-by: Chirag Shah <chirag@cumulusnetworks.com>
The bgp_info data is stored as a void pointer in `struct bgp_node`.
Abstract retrieval of this data and setting of this data
into functions so that in the future we can move around
what is stored in bgp_node.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
It's been a year since we added the new optional parameters
to instantiation. Let's switch over to the new name.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
If we attempt to register nexthops before we have the zebra
connection, they will not be installed. After we have noticed
that we are up, re-install them.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Allow some debug notification when we are unable to talk
to zebra due to the connection not being there yet.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Add the '[no] flood <disable|head-end-replication>' command
to the l2vpn evpn afi/safi sub commands for bgp. This command
when entered as 'flood disable' will turn off type 3 route
generation for the transmittal of the type 3 route necessary
for BUM replication on the remote VTEP. Additionally it will
turn off the BUM handling via the new zebra command,
ZEBRA_VXLAN_FLOOD_CONTROL.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Allow the modification of whether or not we will allow
BUM flooding on the vxlan bridge. To do this allow
the upper level protocol to specify via the ZEBRA_VXLAN_FLOOD_CONTROL
zapi message.
If flooding is disabled then BUM traffic will not be forwarded
to other VTEP's.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Do a straight conversion of `struct bgp_info` to `struct bgp_path_info`.
This commit will setup the rename of variables as well.
This is being done because `struct bgp_info` is not descriptive
of what this data actually is. It is path information for routes
that we keep to build the actual routes nexthops plus some extra
information.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
In bgp if we have not configured bgp we were ignoring
interface based callbacks. Leading to states where
we may not be processing interface information.
Leading to states where we do not actually keep
ifp data. As an example:
Suppose vrf A and vrf B. A has interface swp1.
At the same time we only have a `router bgp 9 vrf B`
When we received the callback for moving swp1
from vrf A to vrf B we were not processing the
move at all and BGP would not consider the interface
part of vrf B at all.
This commit makes bgp pay attention to interface
events irrelevant if bgp is using that vrf. This
is now consistent with how the lib/if* expects
to work and the rest of the daemons in FRR.
Signed-off-by: Donald Sharp <sharpd@cumulsnetworks.com>
Corrections so that the BGP daemon can work with the label manager properly
through a label-manager proxy. Details:
- Correction so the BGP daemon behind a proxy label manager gets the range
correctly (-I added to the BGP daemon, to set the daemon instance id)
- For the BGP case, added an asynchronous label manager connect command so
the labels get recycled in case of a BGP daemon reconnection. With this,
BGPd and LDPd would behave similarly.
Signed-off-by: F. Aragon <paco@voltanet.io>
When using `no bgp fast-external-failover` and a interface moves
from one vrf into another we would not fully process the change.
Fix this code path.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
The peer->nexthop.ifp pointer must be set when parsing the
attributes in bgp_mp_reach_parse, notice this
and fail gracefully.
Rework bgp_nexthop_set to remove the HAVE_CUMULUS and to
fail the nexthop_set when we have a zebra connection and
no ifp pointer, as that not havinga zebra connection and
no ifp pointer is legal.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
