Add the "default-information-originate" option to the "area X nssa"
command. That option allows the origination of Type-7 default routes
on NSSA ABRs and ASBRs.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Considering that both the GR helper mode and restarting mode can be
enabled at the same time, the "graceful-restart helper-only" command
can be a bit misleading since it implies that only the helper mode
is enabled. Rename the command to "graceful-restart helper enable"
to clarify what the command does.
Start a deprecation cycle of one year before removing the original
command
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Considering that both the GR helper mode and restarting mode can be
enabled at the same time, the "graceful-restart helper-only" command
can be a bit misleading since it implies that only the helper mode
is enabled. Rename the command to "graceful-restart helper enable"
to clarify what the command does.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Issue #9535 describes how the export-list/import-list commands work
differently on ospfd and ospf6d.
In short:
* On ospfd, "area A.B.C.D export-list" filters which internal
routes an ABR exports to other areas. On ospf6d, instead, that
command filters which inter-area routes an ABR exports to the
configured area (which is quite counter-intuitive). In other words,
both commands do the same but in opposite directions.
* On ospfd, "area A.B.C.D import-list" filters which inter-area
routes an ABR imports into the configured area. On ospf6d, that
command filters which inter-area routes an interior router accepts.
* On both daemons, "area A.B.C.D filter-list prefix NAME <in|out>"
works exactly the same as import/export lists, but using prefix-lists
instead of ACLs.
The inconsistency on how those commands work is undesirable. This
PR proposes to adapt the ospf6d commands to behave like they do
in ospfd.
These changes are obviously backward incompatible and this PR doesn't
propose any mitigation strategy other than warning users about the
changes in the next release notes. Since these ospf6d commands are
undocumented and work in such a peculiar way, it's unlikely many
users will be affected (if any at all).
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
RFC 5187 specifies the Graceful Restart enhancement to the OSPFv3
routing protocol. This commit implements support for the GR
restarting mode.
Here's a quick summary of how the GR restarting mode works:
* GR can be enabled on a per-instance basis using the `graceful-restart
[grace-period (1-1800)]` command;
* To perform a graceful shutdown, the `graceful-restart prepare ipv6
ospf` EXEC-level command needs to be issued before restarting the
ospf6d daemon (there's no specific requirement on how the daemon
should be restarted);
* `graceful-restart prepare ospf` will initiate the graceful restart
for all GR-enabled instances by taking the following actions:
o Flooding Grace-LSAs over all interfaces
o Freezing the OSPF routes in the RIB
o Saving the end of the grace period in non-volatile memory (a JSON
file stored in `$frr_statedir`)
* Once ospf6d is started again, it will follow the procedures
described in RFC 3623 until it detects it's time to exit the graceful
restart (either successfully or unsuccessfully).
Testing done:
* New topotest featuring a multi-area OSPF topology (including stub
and NSSA areas);
* Successful interop tests against IOS-XR routers acting as helpers.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Added references to some other sysctl knobs that influence behavior
significant to routers, e.g. arp_accept, arp_ignore, bc_forwarding.
Signed-off-by: Trey Aspelund <taspelund@nvidia.com>
Received user feedback that it was unclear how to get into the FRR
shell. Adding a snippet to the basic setup page to help clarify.
Signed-off-by: Trey Aspelund <taspelund@nvidia.com>
Currently the source IP parameter must be entered between destination IP
and destination port parameters. This is not obviously understandable
when you read such config so let's move the source parameter to the end
of the command line, after the whole list of destination parameters. We
can do this without any deprecation cycle as the parameter was introduced
just recently and isn't in any public release yet.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
Add a knob to turn a NSSA area into a totally stub area. In this
configuration a Type-3 default summary route is generated by default.
Syntax: `area A.B.C.D nssa no-summary`.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Add the ability to configure the source address of rpki
connection. Proposed vty command is to add below parameter:
rpki cache <address> source <bindaddr> <port> preference <pref>
rpki cache <address> source <bindaddr> <port> <usernamessh> ...
This works for both tcp and ssh connections. In case the source
address is not available yet, the rpki retry interval will retry
in a defined amount of time.
Rtrlib library is the library in charge of the binding of the
tcp/ssh connection, and applies the getaddrinfo() and bind()
operations to the passed parameter bindaddr to the respective
tcp_config/ssh_config structures.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Add the "metric" and "metric-type" options to the "redistribute"
command.
This is a small commit since the logic of setting the metric
value and type of external routes was already present due to the
implementation of the "default-information originate" command months
ago. This commit merely extends the "redistribute" command to
leverage that functionality.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
While defaults are good picks for "reasonable" guesses, min and max
range values really aren't. Operators and experimenters often like to
configure "unreasonable" values to stress test, tests boundary
conditions and explore innovations.
With that in mind, change all ranges to 1..max (of type).
While we're here add optional ignored values in the "no" CLI forms.
Signed-off-by: Christian Hopps <chopps@labn.net>
Currently the NSSA support is a separate section, but it should actually
be a description of the corresponding CLI command.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
Currently the debugging section is placed in the middle of the section
with various configuration commands.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
