Current command (bundled two into one) is absolutely wrong.
When you configure TCP session with the source, the command thinks, that
it's a SSH session with a username.
It's much better to split this into two separate commands where it's much
easier to do the changes in the future (if more options comes in).
Yes, this is a breaking change, but there is no other proper way to overcome
this.
Bonus note how it looks, which also can lead to crashes (due to port 0x0):
```
(gdb) p *cache->tr_config.ssh_config
$11 = {host = 0x5555562f9cd0 "1.1.1.1", port = 0, bindaddr = 0x0,
username = 0x55555629ad00 "",
server_hostkey_path = 0x7ffff53667a0 <rpki_create_socket> "Uf\017\357\300H\211\345AWAVAUATSH\201", <incomplete sequence \354\230>, client_privkey_path = 0x0,
data = 0x0, new_socket = 0x51, connect_timeout = 4143762592,
password = 0x7ffff6fccca0 <main_arena+96> "\300\"0VUU"}
(gdb) p *cache->tr_config.tcp_config
$12 = {host = 0x5555562f9cd0 "1.1.1.1", port = 0x0, bindaddr = 0x0,
data = 0x55555629ad00, new_socket = 0x7ffff53667a0 <rpki_create_socket>,
connect_timeout = 0}
```
Signed-off-by: Donatas Abraitis <donatas@opensourcerouting.org>
RFC-7607 specifically calls out the allowed usage
of AS 0 to signal that the a particular address is
not in use and should be guarded against. Add
the ability to specify this special AS in the rpki
commands.
eva# show rpki as-number 0
RPKI/RTR prefix table
Prefix Prefix Length Origin-AS
2.57.180.0 22 - 24 0
2.58.144.0 22 - 22 0
2.59.116.0 24 - 24 0
4.42.228.0 22 - 22 0
5.57.80.0 22 - 22 0
<snip>
2a13:df87:b400:: 38 - 38 0
2a13:df84:: 32 - 32 0
2630:: 16 - 16 0
Number of IPv4 Prefixes: 1166
Number of IPv6 Prefixes: 617
eva# show rpki prefix 2630::/16 0
Prefix Prefix Length Origin-AS
2630:: 16 - 16 0
eva#
Fixes: #15778
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Add documentation for per VRF RPKI commands
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
Add an ability to match via route-maps. An additional route-map command
`match rpki-extcommunity <invalid|notfound|valid>` added.
Signed-off-by: Donatas Abraitis <donatas@opensourcerouting.org>
Currently the source IP parameter must be entered between destination IP
and destination port parameters. This is not obviously understandable
when you read such config so let's move the source parameter to the end
of the command line, after the whole list of destination parameters. We
can do this without any deprecation cycle as the parameter was introduced
just recently and isn't in any public release yet.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
Add the ability to configure the source address of rpki
connection. Proposed vty command is to add below parameter:
rpki cache <address> source <bindaddr> <port> preference <pref>
rpki cache <address> source <bindaddr> <port> <usernamessh> ...
This works for both tcp and ssh connections. In case the source
address is not available yet, the rpki retry interval will retry
in a defined amount of time.
Rtrlib library is the library in charge of the binding of the
tcp/ssh connection, and applies the getaddrinfo() and bind()
operations to the passed parameter bindaddr to the respective
tcp_config/ssh_config structures.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
These don't need to be documented, most of the time they are obvious,
when they aren't the behavior can just be described in the command
description.
Signed-off-by: Quentin Young <qlyoung@nvidia.com>
- Generate index entries automatically
- Remove manual command index entries
- Clean up a few other manual index entries
Signed-off-by: Quentin Young <qlyoung@nvidia.com>
The current securing BGP and resource certification reference links lead
to a page not found. This patch fixes that by pointing to their
corresponding PDF format resources.
Signed-off-by: Carlos Goncalves <cgoncalves@redhat.com>
Many index entries used '[no] xxx' or 'no xxx', some had both
positive and 'no' forms. Clean that up mostly - index positive
form of commands only.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
The `bgp bestpath prefix-validate disallow-invalid` command referenced in
the rpki documentation does not actually exist, remove the erroneous docs
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Options must be documented before they can be cross-referenced, and the
scope for configure options is not present in rpki.rst. Remove the
option role tag from the `-M` option to remove the build warning.
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
It has not been properly documented yet how to enable the RPKI module with BGP when having installed FRR with RPKI support. This PR seeks to add a section to the user documentation about this. So users will not have to resolve to searching the internet and looking through the FROG mailing list threads for answers.
Automatically translated all Texinfo files to RST using a script found
on the GCC mailing list[0]. Some formatting manually corrected.
Also created index.rst for building as well as boilerplate Sphinx
conf.py and Makefile.
[0] https://gcc.gnu.org/ml/gcc-patches/2015-11/msg01095.html
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
