Deletion of pim interface(pim_if_delete) should
do the below things before cleanup.
1. Send a hello message with zero hold time.
2. Delete all the neighbors.
3. Close the pim socket.
Signed-off-by: Sarita Patra <saritap@vmware.com>
Fresh ground-up MLD implementation with subscriber-tracking for MLDv2.
Intended to be adapted for IPv4 and replace the IGMP implementation at a
later point.
Tested in ANVL, currently at 94/116. Some issues/TODOs are left in the
code as CPP_NOTICE markers, but the code is very much good enough to
proceed since otherwise we're blocked on overall PIM v6 progress.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
I should've removed this in #10960. It's a hazard in terms of
forgetting to adjust PRs/other changes that might accidentally still
reference the field.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
The only function these macros have is to make the code confusing.
"PIM_IF_DO_PIM" sounds like it triggers some action, but it doesn't.
Replace with "bool" fields in struct pim_interface.
(Note: PIM_IF_*_IGMP_LISTEN_ALLROUTERS was always set, without any way
to unset it. It is completely removed now and always enabled.)
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Adding the Interface level config command
ipv6 mld join
This command can be used to configure the static MLD join
for IPv6 group addresses on the interfaces.
Signed-off-by: Abhishek N R <abnr@vmware.com>
We only care about link-local addresses for IPv6 operation. Also, MLD
needs the lowest while PIM needs the highest...
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
These really don't serve much of a purpose, especially with how
inconsistently they're used.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Modifying the members of pim_interface which are to be used
for both IPv4 and IPv6 to common names(for both MLD and IGMP).
Issues: #10023
Co-authored-by: Mobashshera Rasool <mrasool@vmware.com>
Co-authored-by: Sarita Patra <saritap@vmware.com>
Signed-off-by: Sai Gomathi <nsaigomathi@vmware.com>
Modifying name of struct igmp_sock to struct gm_sock, which is to be used
by both IPv4 and IPv6(for both MLD and IGMP).
Co-authored-by: Mobashshera Rasool <mrasool@vmware.com>
Co-authored-by: Sarita Patra <saritap@vmware.com>
Signed-off-by: Sai Gomathi <nsaigomathi@vmware.com>
Fix:
====
Modifying name of struct igmp_join to struct gm_join, which is to be used
by both IPv4 and IPv6(for both MLD and IGMP).
Co-authored-by: Abhishek N R abnr@vmware.com
Signed-off-by: Mobashshera Rasool <mrasool@vmware.com>
Modifying the members of pim_interface which are to be used
for both IPv4 and IPv6 to common names(for both MLD and IGMP).
Issue: #10023
Co-authored-by: Mobashshera Rasool <mrasool@vmware.com>
Signed-off-by: Sai Gomathi <nsaigomathi@vmware.com>
Since f60a1188 we store a pointer to the VRF in the interface structure.
There's no need anymore to store a separate vrf_id field.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
It allows FRR to read the interface config even when the necessary VRFs
are not yet created and interfaces are in "wrong" VRFs. Currently, such
config is rejected.
For VRF-lite backend, we don't care at all about the VRF of the inactive
interface. When the interface is created in the OS and becomes active,
we always use its actual VRF instead of the configured one. So there's
no need to reject the config.
For netns backend, we may have multiple interfaces with the same name in
different VRFs. So we care about the VRF of inactive interfaces. And we
must allow to preconfigure the interface in a VRF even before it is
moved to the corresponding netns. From now on, we allow to create
multiple configs for the same interface name in different VRFs and
the necessary config is applied once the OS interface is moved to the
corresponding netns.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
Problem Statement:
==================
On new neighbor addition, the tx counter for hello msg is reset.
Fix:
=================
Do not reset the tx counter on new neighbor addition.
Signed-off-by: Mobashshera Rasool <mrasool@vmware.com>
Problem Statement:
==================
pim maintains two counters hello tx and hello rx at interface level.
At present pim needs to send the hello message prior to other pim
message as per RFC. This logic is getting derived from the tx hello
counters. So when a new neighbor is added, tx counters are set to
zero and then based on this, it is further decided to send hello in
pim_hello_require function.
Fix:
====
Separating the hello statistics and the logic to decide when to send hello
based on a new flag. pim_ifstat_hello_sent will be used to note down
the hello stats while a new flag is added to decide whether to send hello
or not if it is the first packet to a neighbor.
Signed-off-by: Mobashshera Rasool <mrasool@vmware.com>
IGMP group/source memberships are a property of the interface; the
particular IP address that the querier used to collect the data is
irrelevant.
... and IGMP packets get delivered only once to pimd anyway, since we
receive them on the "global" per-VRF IGMP socket. (The one in igmp_sock
is only used for sending queries.)
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
When we have a "192.0.2.1 peer 192.0.2.2/32" address on an interface, we
need to (a) recognize the local address as being on the link for our own
packets, and (b) do the IGMP socket lookup with the proper local address
rather than the peer prefix.
Fixes: efe6f18 ("pimd: fix IGMP receive handling")
Cc: Nathan Bahr <nbahr@atcorp.com>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
VRF creation can happen from either cli or from
knowledged about the vrf learned from zebra.
In the case where we learn about the vrf from
the cli, the vrf id is UNKNOWN. Upon actual
creation of the vrf, lib/vrf.c touches up the vrf_id
and calls pim_vrf_enable to turn it on properly.
At this point in time we have a pim->vrf_id of
UNKNOWN and the vrf->vrf_id of the right value.
There is no point in duplicating this data. So just
remove all pim->vrf_id and use the vrf->vrf_id instead
since we keep a copy of the pim->vrf pointer.
This will remove some crashes where we expect the
pim->vrf_id to be usable and it's not.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
