`CFLAGS` is a "user variable", not intended to be controlled by
configure itself. Let's put all the "important" stuff in AC_CFLAGS and
only leave debug/optimization controls in CFLAGS.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
This test establishes a binding between nbma ip of a spoke and its
protocol address. This information is pushed to hub.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Just another round of trying to add pytest.mark.bgpd. Not finished yet just
what I could stand doing for a few minutes.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Description:
BGP session not established for ipv6 link local address with vrf config
Problem Description/Summary :
BGP session not established for ipv6 link local address with vrf configyy
1.Configure ipv6 link-local address fe80::1234/64 on dut1 and fe80::4567/64 on dut2
2.Configure BGP neighbors for ipv6 link-local on both dut1 and dut2
3.Verify BGP session is UP over link-local ipv6 address
4.Observed that bgp session not established for ipv6 link local address
Expected Behavior :
BGP session should be established for ipv6 link local address with vrf config
Signed-off-by: sudhanshukumar22 <sudhanshu.kumar@broadcom.com>
These are for string quoting (`%pSQ`) and string escaping (`%pSE`); the
sets / escape methods are currently rather "basic" and might be extended
in the future.
Signed-off-by: David Lamparter <equinox@diac24.net>
Analogous to Linux kernel `%pV` (but our mechanism expects 2 specifier
chars and `%pVA` is clearer anyway.)
Signed-off-by: David Lamparter <equinox@diac24.net>
... to suppress the warnings when using something that isn't quite ISO C
compatible and would otherwise cause compiler warnings from `-Wformat`.
Signed-off-by: David Lamparter <equinox@diac24.net>
Three new tests:
- OSPFv3 convergence using 'ipv6 ospf6 neighbor json'
- Default route functionality:
* Check that the LSA is present
* Check that the route was installed
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
This replaces `%n` with a safe, out-of-band option that simply records
the start and end offset of the output produced for each `%...`
specifier.
The old `%n` code is removed.
Signed-off-by: David Lamparter <equinox@diac24.net>
Allowing printfrr extensions to directly write to the output buffer has
a few advantages:
- there is no arbitrary length limit imposed (previously 64)
- the output doesn't need to be copied another time
- the extension can directly use bprintfrr() to put together pieces
The downside is that the theoretical length (regardless of available
buffer space) must be computed correctly.
Extended unit tests to test these paths a bit more thoroughly.
Signed-off-by: David Lamparter <equinox@diac24.net>
When "bgp bestpath peer-type multipath-relax" is enabled, multipaths
with both eBGP and iBGP learned routes may exist. It is not desirable
for the iBGP next hops to be discarded from the FIB because they are not
directly connected. When publishing a nexthop group to zebra, the
ZEBRA_FLAG_ALLOW_RECURSION flag is normally not set when the best path
is eBGP; when "bgp bestpath aspath multipath-relax" is configured, the
flag will now be set if any paths are from iBGP peers. This leaves
all-eBGP multipaths still requiring nexthops over connected routes.
Signed-off-by: Joanne Mikkelson <jmmikkel@arista.com>
This new BGP configuration is akin to "bgp bestpath aspath
multipath-relax". When applied, paths learned from different peer types
will be eligible to be considered for multipath (ECMP). Paths from all
of eBGP, iBGP, and confederation peers may be included in multipaths
if they are otherwise equal cost.
This change preserves the existing bestpath behavior of step 10's result
being returned, not the result from steps 8 and 9, in the case where
both 8+9 and 10 determine a winner.
Signed-off-by: Joanne Mikkelson <jmmikkel@arista.com>
