The ACPI specification, up to and including revision 5.1 Errata A, allows
the DSDT and X_DSDT fields to be both set in the FADT. (Obviously, this
only makes sense if the DSDT address is representable in 4 bytes.)
Starting with 5.1 Errata B, specifically for Mantis 1393
<https://mantis.uefi.org/mantis/view.php?id=1393>, the spec requires at
most one of DSDT and X_DSDT to be set to a nonzero value.
MdeModulePkg/AcpiTableDxe handles this mutual exclusion somewhat
inconsistently.
- If the caller of EFI_ACPI_TABLE_PROTOCOL.InstallAcpiTable() installs the
tables in "DSDT, FADT" order, then we enforce the exclusion between the
DSDT and X_DSDT fields:
DSDT under 4GB FADT.DSDT FADT.X_DSDT [VARIANT B]
-------------- --------- -----------
yes set clear
no clear set
This behavior conforms to 5.1 Errata B. (And it's not required by
earlier versions of the spec.)
- If the caller passes in the tables in "FADT, DSDT" relative order, then
we do not enforce the exclusion:
DSDT under 4GB FADT.DSDT FADT.X_DSDT [VARIANT A]
-------------- --------- -----------
yes set set
no clear set
This satisfies 5.1 Errata A and earlier, but breaks 5.1 Errata B and
later.
Unify the handling of both relative orders. In particular, check the major
and minor version numbers in the FADT. If the FADT version is strictly
before 5.1, then implement [VARIANT A]. If the FADT version is equal to or
larger than 5.1, then implement [VARIANT B].
We make three observations:
- We can't check the FADT table version precisely against "5.1 Errata B";
erratum levels are not captured in the table. We err in the safe
direction, namely we enforce the exclusion for "5.1" and "5.1 Errata A".
- The same applies to "6.0" versus "6.0 Errata A". Because we cannot
distinguish these two, we consider "6.0" to be "equal to or larger than
5.1", and apply [VARIANT B], enforcing the exclusion.
- While a blanket [VARIANT B] would be simpler, there is a significant
benefit to [VARIANT A], under the spec versions that permit it:
compatibility with a wider range of OSPMs (typically, older ones).
For example, Igor reported about a "DELL R430 system with rev4 FADT
where DSDT and X_DSDT are pointing to the same address". Michael also
reported about several systems that exhibit the same.
Regression tested with the following KVM guests (QEMU built at
ata0def594286d, "Merge remote-tracking branch
'remotes/bonzini/tags/for-upstream' into staging", 2017-01-30):
- OVMF: boot and S3 suspend/resume
- Ia32, Q35, SMM
- Fedlet 20141209
- Ia32X64, Q35, SMM
- Fedora 22
- Windows 7
- Windows 8.1
- Windows 10
- Windows Server 2008 R2
- Windows Server 2012 R2
- Windows Server 2016 Tech Preview 4
- X64, I440FX, no SMM
- Fedora 24
- RHEL-6.7
- RHEL-7.2-ish
- ArmVirtQemu: boot test with virtio-gpu
- AARCH64
- Fedora 24
- RHELSA-7.3
- openSUSE Tumbleweed (4.8.4-based)
This change is connected to ASWG ticket
<https://mantis.uefi.org/mantis/view.php?id=1757>, which is now
closed/fixed.
Cc: Al Stone <ahs3@redhat.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Leo Duran <leo.duran@amd.com>
Cc: Michael Tsirkin <mtsirkin@redhat.com>
Cc: Phil Dennis-Jordan <phil@philjordan.eu>
Cc: Star Zeng <star.zeng@intel.com>
Reported-by: Phil Dennis-Jordan <phil@philjordan.eu>
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Phil Dennis-Jordan <phil@philjordan.eu>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
This patch incurs no functional changes, it just removes some whitespace,
and also makes sure we always assign
AcpiTableInstance->Fadt3->Dsdt
first, and
AcpiTableInstance->Fadt3->XDsdt
second. The goal is to separate the syntactic changes from the functional
changes implemented by the next patch.
Cc: Al Stone <ahs3@redhat.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Leo Duran <leo.duran@amd.com>
Cc: Michael Tsirkin <mtsirkin@redhat.com>
Cc: Phil Dennis-Jordan <phil@philjordan.eu>
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Architectures such as AArch64 may run the OS with 16 KB or 64 KB sized
pages, and for this reason, the UEFI spec mandates a minimal allocation
granularity of 64 KB for regions that may require different memory
attributes at OS runtime.
So make PeiCore's implementation of AllocatePages () take this into
account as well.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Remove the local definitions for the default and runtime page allocation
granularity macros, and switch to the new MdePkg versions.
Note that this replaces a reference to the 'default' version with the
more correct 'runtime' version, but this matters little in practice.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Remove the local definitions for the default and runtime page allocation
granularity macros, and switch to the new MdePkg versions.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
There are cases that the operands of an expression are all with rank less
than UINT64/INT64 and the result of the expression is explicitly cast to
UINT64/INT64 to fit the target size.
An example will be:
UINT32 a,b;
// a and b can be any unsigned int type with rank less than UINT64, like
// UINT8, UINT16, etc.
UINT64 c;
c = (UINT64) (a + b);
Some static code checkers may warn that the expression result might
overflow within the rank of "int" (integer promotions) and the result is
then cast to a bigger size.
The commit refines codes by the following rules:
1). When the expression is possible to overflow the range of unsigned int/
int:
c = (UINT64)a + b;
2). When the expression will not overflow within the rank of "int", remove
the explicit type casts:
c = a + b;
3). When the expression will be cast to pointer of possible greater size:
UINT32 a,b;
VOID *c;
c = (VOID *)(UINTN)(a + b); --> c = (VOID *)((UINTN)a + b);
4). When one side of a comparison expression contains only operands with
rank less than UINT32:
UINT8 a;
UINT16 b;
UINTN c;
if ((UINTN)(a + b) > c) {...} --> if (((UINT32)a + b) > c) {...}
For rule 4), if we remove the 'UINTN' type cast like:
if (a + b > c) {...}
The VS compiler will complain with warning C4018 (signed/unsigned
mismatch, level 3 warning) due to promoting 'a + b' to type 'int'.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
For pointer subtraction, the result is of type "ptrdiff_t". According to
the C11 standard (Committee Draft - April 12, 2011):
"When two pointers are subtracted, both shall point to elements of the
same array object, or one past the last element of the array object; the
result is the difference of the subscripts of the two array elements. The
size of the result is implementation-defined, and its type (a signed
integer type) is ptrdiff_t defined in the <stddef.h> header. If the result
is not representable in an object of that type, the behavior is
undefined."
In our codes, there are cases that the pointer subtraction is not
performed by pointers to elements of the same array object. This might
lead to potential issues, since the behavior is undefined according to C11
standard.
Also, since the size of type "ptrdiff_t" is implementation-defined. Some
static code checkers may warn that the pointer subtraction might underflow
first and then being cast to a bigger size. For example:
UINT8 *Ptr1, *Ptr2;
UINTN PtrDiff;
...
PtrDiff = (UINTN) (Ptr1 - Ptr2);
The commit will refine the pointer subtraction expressions by casting each
pointer to UINTN first and then perform the subtraction:
PtrDiff = (UINTN) Ptr1 - (UINTN) Ptr2;
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Measure DBT into PCR[7] when it is updated between initial measure
if present and not empty. by following TCG PC Client PFP 00.49
Previous patch for PCR[7] DBT part is overrode.
dc9bd6ed28
Cc: Star Zeng <star.zeng@intel.com>
Cc: Yao Jiewen <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Chao Zhang <chao.b.zhang@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Yao Jiewen <jiewen.yao@intel.com>
To handle the deprecation of PrintLib APIs UnicodeValueToString and
AsciiValueToString by subsequent commits, the commit refines the logic for
the implemetation of the UnicodeValueToString and AsciiValueToString
services in EFI_PRINT2_PROTOCOL.
When the macro DISABLE_NEW_DEPRECATED_INTERFACES is defined (indicating
the deprecation of the PrintLib APIs), the above two services will ASSERT
and will return zero to reflect not being supported.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
It is the follow up of commits 51f0ceb..9e32e97 to replace
AsciiValueToString/UnicodeValueToString with
AsciiValueToStringS/UnicodeValueToStringS.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
This PCD holds the address mask for page table entries when memory
encryption is enabled on AMD processors supporting the Secure Encrypted
Virtualization (SEV) feature.
This module updates the under-4GB page tables configured by the S3-Resume
code in UefiCpuPkg/Universal/Acpi/S3Resume2Pei. The mask is saved at module
start (ScriptExecute.c), and applied when tables are expanded on-demand by
page-faults above 4GB's (SetIdtEntry.c).
CC: Jeff Fan <jeff.fan@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Leo Duran <leo.duran@amd.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
This PCD holds the address mask for page table entries when memory
encryption is enabled on AMD processors supporting the Secure Encrypted
Virtualization (SEV) feature.
The mask is applied when 4GB tables are created (UefiCapsule.c), and when
the tables are expanded on-demand by page-faults above 4GB's (X64Entry.c).
Cc: Feng Tian <feng.tian@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Leo Duran <leo.duran@amd.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
This PCD holds the address mask for page table entries when memory
encryption is enabled on AMD processors supporting the Secure Encrypted
Virtualization (SEV) feature.
The mask is applied when creating page tables.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Leo Duran <leo.duran@amd.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
This PCD holds the address mask for page table entries when memory
encryption is enabled on AMD processors supporting the Secure Encrypted
Virtualization (SEV) feature.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Signed-off-by: Leo Duran <leo.duran@amd.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
This implements a DXE memory protection policy that ensures that regions
that don't require executable permissions are mapped with the non-exec
attribute set.
First of all, it iterates over all entries in the UEFI memory map, and
removes executable permissions according to the configured DXE memory
protection policy, as recorded in PcdDxeNxMemoryProtectionPolicy.
Secondly, it sets or clears the non-executable attribute when allocating
or freeing pages, both for page based or pool based allocations.
Note that this complements the image protection facility, which applies
strict permissions to BootServicesCode/RuntimeServicesCode regions when
the section alignment allows it. The memory protection configured by this
patch operates on non-code regions only.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Define a new fixed/patchable PCD that sets the DXE memory protection
policy: its primary use is to define which memory types should have
their executable permissions removed. Combined with the image protection
policy, this can be used to implement a strict W^X policy, i.e.. a policy
where no regions exist that are both executable and writable at the same
time.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
In preparation of adding memory permission attribute management to
the pool allocator, split off the locking of the pool metadata into
a separate lock. This is an improvement in itself, given that pool
allocations can only interfere with the page allocation bookkeeping
if pool pages are allocated or released. But it is also required to
ensure that the permission attribute management does not deadlock,
given that it may trigger page table splits leading to additional
page tables being allocated.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
The EBC driver emits thunks for native to EBC calls, which are short
instructions sequences that bridge the gap between the native execution
environment and the EBC virtual machine.
Since these thunks are allocated using MemoryAllocationLib::AllocatePool(),
they are emitted into EfiBootServicesData regions, which does not reflect
the nature of these thunks accurately, and interferes with strict memory
protection policies that map data regions non-executable.
So instead, create a new helper EbcAllocatePoolForThunk() that invokes the
AllocatePool() boot service directly to allocate EfiBootServicesCode pool
memory explicitly, and wire up this helper for the various architecture
specific thunk generation routines.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Ensure that any memory allocated for PE/COFF images is identifiable as
a boot services code region, so that we know it requires its executable
permissions to be preserved when we tighten mapping permissions later on.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
1. Make function comments align with the function.
2. Change the FILE_GUID value in SmmSmiHandlerProfileLib.inf
since it is duplicated with the FILE_GUID value in
SmiHandlerProfileLibNull.inf
3. Add missing PCD PROMPT&HELP string to uni file.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Use the API EfiBootManagerDeleteLoadOptionVariable in UefiBootManagerLib to
replace the same logic in function Var_DelBootOption/Var_DelDriverOption.
This can make code clean and prevent potential bugs.
https://bugzilla.tianocore.org/show_bug.cgi?id=391
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Having duplicated DNS server IPs specified is not an ideal
configuration, but not an error condition. This patch is to
remove the duplicated DNS address check to allow the same DNS
address setting in SetData().
Cc: Hegde Nagaraj P <nagaraj-p.hegde@hpe.com>
Cc: Subramanian Sriram <sriram-s@hpe.com>
Cc: Ye Ting <ting.ye@intel.com>
Cc: Fu Siyuan <siyuan.fu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Wu Jiaxin <jiaxin.wu@intel.com>
Reviewed-by: Subramanian Sriram <sriram-s@hpe.com>
Reviewed-by: Hegde Nagaraj P <nagaraj-p.hegde@hpe.com>
Tested-by: Hegde Nagaraj P <nagaraj-p.hegde@hpe.com>
Instead of assuming that a PE/COFF section of type EFI_IMAGE_SCN_CNT_CODE
can always be mapped read-only, classify a section as a code section only
if it has the executable attribute set and the writable attribute cleared.
This adheres more closely to the PE/COFF spec, and avoids issues with
Linux OS loaders that may consist of a single read/write/execute section.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Update the interface name from ethA ethB to
eth10, eth11 etc if port number more than 9.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Zhang Lubo <lubo.zhang@intel.com>
Cc: Sriram Subramanian <sriram-s@hpe.com>
Cc: Ye Ting <ting.ye@intel.com>
Cc: Fu Siyuan <siyuan.fu@intel.com>
Cc: Wu Jiaxin <jiaxin.wu@intel.com>
Reviewed-by: Sriram Subramanian <sriram-s@hpe.com>
Reviewed-by: Wu Jiaxin <jiaxin.wu@intel.com>
Reviewed-by: Fu Siyuan <siyuan.fu@intel.com>
This app uses SMM communication to get SMI handler profile
from SMM core.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
1) SmmCore maintains the root SMI handler and NULL SMI handler
database.
2) SmmCore consumes PcdSmiHandlerProfilePropertyMask to decide
if SmmCore need support SMI handler profile.
If SMI handler profile is supported, the SmmCore installs
SMI handler profile protocol and SMI handler profile
communication handler.
3) SMI handler profile protocol will record the hardware SMI
handler profile registered by SmmChildDispatcher.
4) SMI handler profile communication handler will return all
SMI handler profile info (NULL SMI handler, GUID SMI handler,
and hardware SMI handler)
Cc: Feng Tian <feng.tian@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
This instance should be linked by SmmChildDispatcher
if SMI handler profile feature is enabled.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
This PCD is linked by PiSmmCore to control if it enables
SMI handler profile feature.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
This header file defines:
1) An SMI handler profile protocol. So that SmmChildDispatch
module can register the hardware SMI handler information.
2) The SMI handler profile communication buffer. So that
a shell application can use SMM communication to get the
SMI handler profile info.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
If the UEFI image is page aligned, the image code section is set to read
only and the image data section is set to non-executable.
1) This policy is applied for all UEFI image including boot service driver,
runtime driver or application.
2) This policy is applied only if the UEFI image meets the page alignment
requirement.
3) This policy is applied only if the Source UEFI image matches the
PcdImageProtectionPolicy definition.
4) This policy is not applied to the non-PE image region.
The DxeCore calls CpuArchProtocol->SetMemoryAttributes() to protect
the image. If the CpuArch protocol is not installed yet, the DxeCore
enqueues the protection request. Once the CpuArch is installed, the
DxeCore dequeues the protection request and applies policy.
Once the image is unloaded, the protection is removed automatically.
The UEFI runtime image protection is teared down at ExitBootServices(),
the runtime image code relocation need write code segment at
SetVirtualAddressMap(). We cannot assume OS/Loader has taken over
page table at that time.
NOTE: It is per-requisite that code section and data section
should not be not merged. That is same criteria for SMM/runtime driver.
We are not able to detect during BIOS boot, because
we can only get LINK warning below:
"LINK : warning LNK4254: section '.data' (C0000040) merged into
'.text' (60000020) with different attributes"
But final attribute in PE code section is same.
Cc: Star Zeng <star.zeng@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Michael Kinney <michael.d.kinney@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
There exits the case that when saving changes in form A,
the old saved data in form B are not cleaned, will be saved
again with the new save. Thus incorrect UI behavior will be
shown. This patch is to remove some useless data.
https://bugzilla.tianocore.org/show_bug.cgi?id=385
Cc: Eric Dong <eric.dong@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
For string op-code, the default string may not reach the
maximum size, so when generating <AltResp> string, we should
clean the value before setting the default string.
https://bugzilla.tianocore.org/show_bug.cgi?id=375
Cc: Eric Dong <eric.dong@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
When set value to the array "InputText", the index was used incorrectly.
And the array "InputText" is not initialized. These will cause some value
in the array is random, so it will be shown incorrectly sometimes.
This patch is to fix this issue.
https://bugzilla.tianocore.org/show_bug.cgi?id=358
Cc: Eric Dong <eric.dong@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Cc: Wang Cloud <winggundum82@163.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Add the following 2 APIs:
UnicodeValueToStringS
AsciiValueToStringS
These safe version APIs are used to enhance their counterpart (APIs
without trailing 'S' in function names).
They perform checks to the input parameters and will return relative
status to reflect the check result.
Return RETURN_INVALID_PARAMETER when:
1). The input Buffer is NULL.
2). The input BufferSize is greater than (PcdMaximumUnicodeStringLength *
sizeof (CHAR16) + 1) for UnicodeValueToStringS or greater than
PcdMaximumAsciiStringLength for AsciiValueToStringS.
3). The input Flags is not set properly.
4). The input Width is not smaller than MAXIMUM_VALUE_CHARACTERS.
Return RETURN_BUFFER_TOO_SMALL when:
1). The input BufferSize cannot hold the converted value.
These APIs in the MdeModulePkg/DxePrintLibPrint2Protocol instance
follow the same rules with MdePkg/BasePrintLib.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
The commit updates the PrintLib instance
MdeModulePkg/Library/DxePrintLibPrint2Protocol to use EFI_PRINT2S_PROTOCOL
to implement the APIs.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Add the EFI_PRINT2S_PROTOCOL as a safe version of the EFI_PRINT2_PROTOCOL,
the EFI_PRINT2S_PROTOCOL replaces the following 2 services in
EFI_PRINT2_PROTOCOL:
UNICODE_VALUE_TO_STRING
ASCII_VALUE_TO_STRING
with:
UNICODE_VALUE_TO_STRING_S
ASCII_VALUE_TO_STRING_S
The 2 new services perform checks to the input parameters and will return
relative status to reflect the check result.
Return RETURN_INVALID_PARAMETER when:
1). The input Buffer is NULL.
2). The input BufferSize is greater than (PcdMaximumUnicodeStringLength *
sizeof (CHAR16) + 1) for UnicodeValueToStringS or greater than
PcdMaximumAsciiStringLength for AsciiValueToStringS.
3). The input Flags is not set properly.
4). The input Width is not smaller than MAXIMUM_VALUE_CHARACTERS.
Return RETURN_BUFFER_TOO_SMALL when:
1). The input BufferSize cannot hold the converted value.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
For the following 8 services in EFI_PRINT2_PROTOCOL:
UNICODE_BS_PRINT
UNICODE_S_PRINT
UNICODE_BS_PRINT_ASCII_FORMAT
UNICODE_S_PRINT_ASCII_FORMAT
ASCII_BS_PRINT
ASCII_S_PRINT
ASCII_BS_PRINT_UNICODE_FORMAT
ASCII_S_PRINT_UNICODE_FORMAT
They will ASSERT when:
1) The input parameter 'StartOfBuffer' is NULL if 'BufferSize' indicates
at least 1 Ascii/Unicode character can be held.
2) The input parameter 'FormatString' is NULL if 'BufferSize' indicates at
least 1 Ascii/Unicode character can be held.
3) The input parameter 'FormatString' contains more than
PcdMaximum[Ascii|Unicode]StringLength Ascii/Unicode characters.
4) The produced string contains more than
PcdMaximum[Ascii|Unicode]StringLength Ascii/Unicode characters.
This commits removes the ASSERT case 4) and add the following new ASSERT
case:
4) The input parameter 'BufferSize' is greater than
(PcdMaximumAsciiStringLength * sizeof (CHAR8)) for Ascii format string or
(PcdMaximumUnicodeStringLength * sizeof (CHAR16) + 1) for Unicode format
string.
And for those ASSERT cases, 0 will be returned by those services.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
For the following 12 APIs in MdeModulePkg/DxePrintLibPrint2Protocol:
UnicodeVSPrint
UnicodeBSPrint
UnicodeSPrint
UnicodeVSPrintAsciiFormat
UnicodeBSPrintAsciiFormat
UnicodeSPrintAsciiFormat
AsciiVSPrint
AsciiBSPrint
AsciiSPrint
AsciiVSPrintUnicodeFormat
AsciiBSPrintUnicodeFormat
AsciiSPrintUnicodeFormat
They will ASSERT when:
1) The input parameter 'StartOfBuffer' is NULL if 'BufferSize' indicates
at least 1 Ascii/Unicode character can be held.
2) The input parameter 'FormatString' is NULL if 'BufferSize' indicates at
least 1 Ascii/Unicode character can be held.
3) The input parameter 'FormatString' contains more than
PcdMaximum[Ascii|Unicode]StringLength Ascii/Unicode characters.
4) The produced string contains more than
PcdMaximum[Ascii|Unicode]StringLength Ascii/Unicode characters.
This commits removes the ASSERT case 4) and add the following new ASSERT
case:
4) The input parameter 'BufferSize' is greater than
(PcdMaximumAsciiStringLength * sizeof (CHAR8)) for Ascii format string or
(PcdMaximumUnicodeStringLength * sizeof (CHAR16) + 1) for Unicode format
string.
And for those ASSERT cases, 0 will be returned by those 12 APIs.
For the following 2 APIs in MdeModulePkg/DxePrintLibPrint2Protocol:
SPrintLength
SPrintLengthAsciiFormat
They will ASSERT when:
1) The input parameter 'FormatString' is NULL.
2) The input parameter 'FormatString' contains more than
PcdMaximum[Ascii|Unicode]StringLength Ascii/Unicode characters.
And for those ASSERT cases, 0 will be returned by those 2 APIs.
Now these APIs in the MdeModulePkg/DxePrintLibPrint2Protocol instance
follow the same rules with MdePkg/BasePrintLib.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Currently, When there are more than 9 Ethernet ports available,
'ifconfig -l' is not listing all the ports, only show the ports 0 to 9.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Zhang Lubo <lubo.zhang@intel.com>
Cc: Santhapur Naveen <naveens@amiindia.co.in>
Cc: Ye Ting <ting.ye@intel.com>
Cc: Fu Siyuan <siyuan.fu@intel.com>
Cc: Wu Jiaxin <jiaxin.wu@intel.com>
Reviewed-by: Ye Ting <ting.ye@intel.com>
Reviewed-by: Wu Jiaxin <jiaxin.wu@intel.com>
Compiler calculates the PciBar[BarIndex] using
sizeof (PciBar[0]) * BarIndex, when BarIndex is type of UINT64,
the above calculation generates assembly code using _allmul.
Change BarIndex to UINTN to avoid the build failure.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Wu Jiaxin <jiaxin.wu@intel.com>
When the VendorId/DeviceId/RevisionId/SubsystemVendorId
/SubsystemDeviceId is MAX_UINTN, IncompatiblePciDeviceSupport
driver doesn't use it to match any IDs.
The patch fixes this bug.
Since PciBus driver always calls IncompatiblePciDeviceSupport
using IDs read from HW, MAX_UINTN is never passed to this
driver.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
The patch replaces the following macros:
DEVICE_ID_NOCARE (0xFF) --> MAX_UINT64
PCI_ACPI_UNUSED (0) --> 0
PCI_BAR_ALL (0xFF) --> MAX_UINT64
PCI_BAR_NOCHANGE (0) --> 0
PCI_BAR_EVEN_ALIGN --> EVEN_ALIGN (local definition)
Since the PciBus driver was updated to accept Spec defined values
in previous commit, the above replacements don't impact
functionality.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
PI spec IncompatiblePciSupport part defines (UINT64)-1 as all BARs
and 0 to use existing alignment. PciBus driver didn't accept these
values. It treated 0xFF as all BARs and 0xFFFFFFFFFFFFFFFFULL to use
existing alignment.
The patch changes the code to still accept old values while also
accept values defined in PI spec. So that the driver can provide
backward compatibility and follow spec.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
When BarIndex equals to 0xFF, default value 0 is used as the BAR
index. Though PCI_BAR_ALL and MAX_UINT8 shares the same value,
using PCI_BAR_ALL is like to match any BAR not BAR 0, it's more
proper to use MAX_UINT8 here.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
If GUIDED section authentication has EFI_AUTH_STATUS_NOT_TESTED, its
matched extraction ppi may not be installed. So, don't cache its data.
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
When PEIM is security violation, its matched extraction ppi may not be
installed. So, its PeimNeedingDispatch will still reset to TRUE.
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Replace AsciiStrDecimalToUintn with AsciiStrDecimalToUintnS to
return the correct status for the HTTP Port/ContentLength.
Cc: Ye Ting <ting.ye@intel.com>
Cc: Fu Siyuan <siyuan.fu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Wu Jiaxin <jiaxin.wu@intel.com>
Reviewed-by: Fu Siyuan <siyuan.fu@intel.com>
Reviewed-by: Ye Ting <ting.ye@intel.com>
BmExpandMediaDevicePath contains a bug that it uses the
uninitialized Handle.
Since the function is called when the Handle supports BlockIo
or SimpleFileSystem, when there is no SimpleFileSystem installed
on the Handle, BlockIo is *guaranteed* to be installed on the Handle.
The fix initializes the Handle by locating the BlockIo protocol
from the device path.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Sunny Wang <sunnywang@hpe.com>
Use UEFI_VARIABLE_DATA data structure according to TCG PC-Client PFP Spec
00.21.
http://www.trustedcomputinggroup.org/wp-content/uploads/PC-ClientSpecific_Platform_Profile_for_TPM_2p0_Systems_v21.pdf
Cc: Star Zeng <star.zeng@intel.com>
Cc: Yao Jiewen <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Chao Zhang <chao.b.zhang@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Yao Jiewen <jiewen.yao@intel.com>
https://bugzilla.tianocore.org/show_bug.cgi?id=339
The patch refines ConfigurePixelBitMaskFormat() to prepare the
enhancement in next commit: Enhance this library to use dynamic
allocated line buffer to reduce memory usage of frame buffer
configure.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Measure DBT into PCR[7] when it is updated between initial measure and
ExitBootService. Measure "SecureBoot" change after PK update.
Spec version : TCG PC Client PFP 00.37. http://www.trustedcomputinggroup.org/wp-content/uploads/PC-ClientSpecific_Platform_Profile_for_TPM_2p0_Systems_v21.pdf
Cc: Star Zeng <star.zeng@intel.com>
Cc: Yao Jiewen <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Chao Zhang <chao.b.zhang@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Yao Jiewen <jiewen.yao@intel.com>
If the code eventually returns "Status" anyway, it does not make
sense to explicitly return "Status" in case of an error, too.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
The OCS value should be initiliazed as 0x0F according to UFS spec.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Reviewed-by: Feng Tian <feng.tian@intel.com>
The OCS value should be initiliazed as 0x0F according to UFS spec.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Reviewed-by: Feng Tian <feng.tian@intel.com>
When UPIU packet is sent, (BIT0 << Slot) should be set according
to context. But BIT0 is used without Slot when UfsWaitMemSet ()
is invoked.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Reviewed-by: Feng Tian <feng.tian@intel.com>
When UPIU packet is sent, (BIT0 << Slot) should be set according
to context. But BIT0 is used without Slot when UfsWaitMemSet ()
is invoked.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Reviewed-by: Feng Tian <feng.tian@intel.com>
When UFS_HC_CAP_64ADDR bit is set, it means 64-bit address,
not 32-bit address.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Reviewed-by: Feng Tian <feng.tian@intel.com>
https://bugzilla.tianocore.org/show_bug.cgi?id=324
Enhance the FileExplorerlib so that user can create a new file/folder
through the UI page.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
https://bugzilla.tianocore.org/show_bug.cgi?id=342
When user select and enter a directory, File Explorer will update the
form based on the new folders and files in the directory. But when
creating question opcodes, the question id is same with previous one
and this will cause browser to show the highlight menu incorrectly.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
https://bugzilla.tianocore.org/show_bug.cgi?id=323
FileExplorer no need to search load file protocol to show files.
Now remove the codes.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Pass '&Node.Header' instead of '&Node' as the 1st parameter to function
SetDevicePathNodeLength().
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
DxeCorePerformanceLib is the performance log manager of PEI and DXE
phase, and it will also produce Performance(Ex) protocol, it should
only support linking with DxeCore.
Cc: Liming Gao <liming.gao@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Refine the codes to compare the definition 'SIZE_4GB' with type
EFI_PHYSICAL_ADDRESS.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
The type of return value for function EfiBootManagerFindLoadOption() is
INTN. When checking its return value, it is unnecessary to type cast -1 to
type UINTN.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Sunny Wang <sunnywang@hpe.com>
When gDS->SetMemorySpaceCapabilities() is called,
current DXE core will sync all GCD attributes to memory map
attributes, including RUNTIME attributes.
It is wrong, because RUNTIME attributes should be set for
runtime memory only.
This fix clears the RUNTIME attributes before convert to UEFI
memory map. So that the UEFI memory map is good after
gDS->SetMemorySpaceCapabilities() is called.
Cc: Star Zeng <star.zeng@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
TerminalDxe driver contains bugs in its DriverBindingStart():
1. It cannot be started AGAIN using a different terminal type;
2. It doesn't install SimpleTextInput/SimpleTextOut when
ConIn/ConOut doesn't contain its device path. The check is
duplicated of the same logic in ConPlatform driver and can
be removed.
The patch optimized the code to remove the unnecessary
gEfiCallerIdGuid protocol installation.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
If a BaseAddress of NULL is passed into DXE Core services
CoreAllocateIoSpace() or CoreAllocateMemorySpace(), and
DEBUG() messages are enabled, then a NULL pointer reference
is made. The parameter check for BaseAddress is performed
in the function CoreAllocateSpace() after the DEBUG()
messages. A check is added in the DEBUG() messages to
prevent the NULL pointer reference.
This issue was found with PI SCTs with DEBUG messages
enabled in the DXE Core.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Michael Kinney <michael.d.kinney@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Feng Tian <feng.tian@Intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
When firmware boots to UiApp, the memory type information settings
are saved to NV storage and the settings in HOB are changed as well.
Because UiApp is an APPLICATION type of boot option, system doesn't
reset when settings change.
But when user selects OS to boot in UiApp, because the settings in HOB
was updated when booting to UiApp, the BDS doesn't think the settings
change, expected reset doesn't happen.
The patch fixes this issue to not update the settings in HOB.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Sunny Wang <sunnywang@hpe.com>
Ip4Config2SetDnsServer may cause ASSERT if the invalid DNS
server address received. The issue is triggered by the NULL
pointer(Tmp) free.
Cc: Ye Ting <ting.ye@intel.com>
Cc: Fu Siyuan <siyuan.fu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Wu Jiaxin <jiaxin.wu@intel.com>
Reviewed-by: Fu Siyuan <siyuan.fu@intel.com>
Reviewed-by: Ye Ting <ting.ye@intel.com>
The BootScriptWriteMemPoll() helper function in both drivers does the
following:
- pop Delay from the variable argument list as UINT64, then truncate it to
UINTN,
- divide Delay by 10, using DivU64x32Remainder(), then store the quotient
in LoopTimes (also UINTN),
- pass LoopTimes to S3BootScriptSaveMemPoll() as last argument.
The truncation to UINTN is superfluous and wrong in this logic (not to
mention incompatible with the PI spec); it prevents callers from
specifying Delays longer than 0xFFFF_FFFF * 100ns (approximately 429
seconds == 7 minutes 9 seconds) on Ia32. In particular it prevents callers
from specifying an infinite timeout (for example, 0xFFFF_FFFF_FFFF_FFFF *
100ns, approximately 58494 years).
Change the type of Delay and LoopTimes to UINT64. Keep the same logic,
just remove the truncations. The resultant LoopTimes values can be safely
passed to S3BootScriptSaveMemPoll() thanks to the previous patch.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: "Yao, Jiewen" <jiewen.yao@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
The BaseNull instance of S3BootScriptLib obviously doesn't care about the
type of the S3BootScriptSaveMemPoll() function's LoopTimes parameter; this
lib instance doesn't do anything with the parameters received in
S3BootScriptSaveMemPoll().
The PiDxe instance saves the LoopTimes parameter in
EFI_BOOT_SCRIPT_MEM_POLL.LoopTimes. This target field already has UINT64
type. Furthermore, the BootScriptExecuteMemPoll() function in the same
library instance already uses a local UINT64 variable called LoopTimes to
count up to EFI_BOOT_SCRIPT_MEM_POLL.LoopTimes. This means that the the
UINTN type for S3BootScriptSaveMemPoll()'s LoopTimes parameter is an
unnecessary restriction.
The callers of S3BootScriptSaveMemPoll() will be updated in the next
patches, functionally. At this stage, they will continue to compile, since
UINT64 parameters can accept UINTN arguments.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: "Yao, Jiewen" <jiewen.yao@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
https://bugzilla.tianocore.org/show_bug.cgi?id=307
For the following APIs in PrintLib instance
MdeModulePkg\Library\DxePrintLibPrint2Protocol:
UnicodeVSPrint
UnicodeSPrint
UnicodeVSPrintAsciiFormat
UnicodeSPrintAsciiFormat
AsciiVSPrint
AsciiSPrint
AsciiVSPrintUnicodeFormat
AsciiSPrintUnicodeFormat
The internal function DxePrintLibPrint2ProtocolVaListToBaseList() will be
called to convert a VA_LIST to a BASE_LIST. However, those APIs miss
checking the return value of the internal function.
This commit adds codes to check the return value. If the VA_LIST fails to
be converted to a BASE_LIST, those PrintLib APIs will return 0 and leave
the output 'StartOfBuffer' unmodified.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Current implementation executes key notify function in TimerHandler
at TPL_NOTIFY. The code change is to make key notify function
executed at TPL_CALLBACK to reduce the time occupied at TPL_NOTIFY.
The code will signal KeyNotify process event if the key pressed
matches any key registered and insert the KeyData to the EFI Key
queue for notify, then the KeyNotify process handler will invoke
key notify functions at TPL_CALLBACK.
Cc: Ruiyu Ni <Ruiyu.ni@intel.com>
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Ruiyu Ni <Ruiyu.ni@intel.com>
Current implementation executes key notify function in TimerHandler
at TPL_NOTIFY. The code change is to make key notify function
executed at TPL_CALLBACK to reduce the time occupied at TPL_NOTIFY.
The code will signal KeyNotify process event if the key pressed
matches any key registered and insert the KeyData to the EFI Key
queue for notify, then the KeyNotify process handler will invoke
key notify functions at TPL_CALLBACK.
Cc: Ruiyu Ni <Ruiyu.ni@intel.com>
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Ruiyu Ni <Ruiyu.ni@intel.com>
Current implementation executes key notify function in TimerHandler
at TPL_NOTIFY. The code change is to make key notify function
executed at TPL_CALLBACK to reduce the time occupied at TPL_NOTIFY.
The code will signal KeyNotify process event if the key pressed
matches any key registered and insert the KeyData to the EFI Key
queue for notify, then the KeyNotify process handler will invoke
key notify functions at TPL_CALLBACK.
Cc: Ruiyu Ni <Ruiyu.ni@intel.com>
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Ruiyu Ni <Ruiyu.ni@intel.com>
Register key notify for toggle state (CapsLock, NumLock and ScrollLock)
sync between multiple keyboards.
The implementation for this feature requires keyboard driver supports
EFI_KEY_STATE_EXPOSED, and turns on physical TextInEx partial key
report for toggle state sync.
The virtual TextInEx will report the partial key after it is required
by calling SetState(X | KEY_STATE_VALID_EXPOSED) explicitly.
Cc: Ruiyu Ni <Ruiyu.ni@intel.com>
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Ruiyu Ni <Ruiyu.ni@intel.com>
Previous logic does not follow UEFI 22.2.3 to process FMP strictly.
It may cause FMP image not be processed in some corner case.
The updated logic follows UEFI 22.2.3.
The way to check if a capsule is processed is also simplified.
The function - ProcessFmpCapsuleImage() is too big, so that
we created sub-functions - StartFmpImage(), DumpAllFmpInfo(),
GetFmpHandleBufferByType(), SetFmpImageData(), RecordFmpCapsuleStatus()
to improve the readability.
The function - ProcessTheseCapsules() is too big, so that
we created sub-functions - InitCapsulePtr(), AreAllImagesProcessed(),
PopulateCapsuleInConfigurationTable() to improve the readability.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Chao Zhang <chao.b.zhang@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
According to UEFI spec, capsule result variable may roll over to 0.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Chao Zhang <chao.b.zhang@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
According to UEFI spec, capsule report variable should include
a null terminator for capsule name and capsule target, if they are
not present.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
According to UEFI spec, capsule report variable should include
a null terminator for capsule name and capsule target, if they are
not present.
The reserved field is zeroed.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
This commit refines the logic for the CvtNum function. It avoids using the
decrement operator '--' for array index to prevent possible mis-reports by
static code checkers.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Fu Siyuan <siyuan.fu@intel.com>
Reviewed-by: Ye Ting <ting.ye@intel.com>
Reviewed-by: Wu Jiaxin <jiaxin.wu@intel.com>
This commit rewrites the logic for NetblockChecksum. It processes the
checksum of the left-over byte first to prevent possible mis-reports by
static code checkers.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Fu Siyuan <siyuan.fu@intel.com>
Reviewed-by: Ye Ting <ting.ye@intel.com>
Reviewed-by: Wu Jiaxin <jiaxin.wu@intel.com>
For variable name, it should contain lower case characters.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
This patch remove the ASSERT when receive a DHCP packet large than the maximum
cache buffer size.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Fu Siyuan <siyuan.fu@intel.com>
Reviewed-by: Ye Ting <ting.ye@intel.com>
Reviewed-by: Wu Jiaxin <jiaxin.wu@intel.com>
Add support for non-coherent DMA, either by performing explicit cache
maintenance when DMA mappings are aligned to the CPU's DMA buffer alignment,
or by bounce buffering via uncached mappings otherwise.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Some Pcds are added to the dec file, but miss to add the
prompt&&help info to the uni file, now add them.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Fix switch/case statement type mismatch in functions PciIoMemRead &
PciIoMemWrite.
Parameter 'Width' is of enum type EFI_PCI_IO_PROTOCOL_WIDTH, but the enum
type provided in 'switch (Width)' block is of type
EFI_PCI_ROOT_BRIDGE_IO_PROTOCOL_WIDTH.
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
PiSmmIpl records LoadModuleAtFixAddressSmramBase in LMFAConfigurationTable.
Update PiSmmCore to directly get the address from this system table.
Cc: Star Zeng <star.zeng@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Allocate the additional Smram range to describe the reserved smram for
SMM core and driver when LMFA feature is enabled.
Cc: Star Zeng <star.zeng@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
https://bugzilla.tianocore.org/show_bug.cgi?id=278
Zero memory address or zero number pages are invalid to SmmFreePages().
Cc: Star Zeng <star.zeng@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
REF: https://bugzilla.tianocore.org/show_bug.cgi?id=290
Current SmmVariableGetStatistics() in VariableSmm.c is always
checking input InfoSize against the first variable info,
it is incorrect.
For instance, there are three variables.
BootOrder
Boot0000
Boot0001
If the input InfoEntry is holding the second variable info (Boot0000)
and InfoSize is sizeof (VARIABLE_INFO_ENTRY) + StrSize (L"Boot0000"),
current code will return EFI_BUFFER_TOO_SMALL, but it should return
the third variable info (Boot0001).
This patch is to refine the code logic.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Current code in SmmVariableHandler() checks CommBufferSize
buffer to make sure it points to outside SMRAM in
"case SMM_VARIABLE_FUNCTION_GET_STATISTICS".
But after eaae7b33b1,
CommBufferSize buffer points to SMRAM that was used by
SMM core to cache CommSize from SmmCommunication protocol,
then the check will fail definitely and GET_STATISTICS
feature breaks.
In fact, do not need check CommBufferSize buffer at all
even before eaae7b33b1.
Before eaae7b33b1,
CommBufferSize buffer pointed to gSmmCorePrivate->BufferSize
that is outside SMRAM, the check will success definitely;
after eaae7b33b1,
CommBufferSize buffer points to local variable BufferSize
(in SMRAM) in SmmEntryPoint(), the check is not needed
definitely.
The patch is to remove the check.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Jeff Fan <jeff.fan@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Add missing EFIAPI modifiers to the functions that are exposed via the
PCI I/O protocol.
At the same time, add a missing UINT8 cast which breaks the build on
Visual Studio.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Dandan Bi <dandan.bi@intel.com>
PlatformBootManagerBeforeConsole() might want to trigger this event
to connect ConIn so BdsDxe initializes this event before
PlatformBootManagerBeforeConsole().
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Sunny Wang <sunnywang@hpe.com>
Cc: Chao B Zhang <chao.b.zhang@intel.com>
This implements support for non-discoverable PCI compatible devices, i.e,
devices that are not on a PCI bus but that can be controlled by generic PCI
drivers in EDK2.
This is implemented as a UEFI driver, which means we take full advantage
of the UEFI driver model, and only instantiate those devices that are
necessary for booting.
Care is taken to deal with DMA addressing limitations: DMA mappings and
allocations are moved below 4 GB if the PCI driver has not informed us
that the device being driven is 64-bit DMA capable. DMA is implemented as
coherent, support for non-coherent DMA is implemented by a subsequent patch.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Non-discoverable devices need to be registered explicitly by the platform.
Introduce a helper library that takes care of this.
This implementation currently only supports registering devices that are
covered by one or more MMIO resources. The underlying protocol allows for
more flexibility than that, but this is currently sufficient for the use
cases that we know about.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Introduce a protocol that can be exposed by a platform for devices that
are not discoverable, usually because they are wired straight to the
memory bus rather than to an enumerable bus like PCI or USB.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
The bug is caused by using already freed memory.
If there is already an attempt and execute
'reconnect -r' command, all the ConfigFormEntry structure
will be freed in IScsiDriverBindingStop, but the
mCallbackInfo->Current is not configured as null and
this pointer will be used again in IScsiFormExtractConfig.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Zhang Lubo <lubo.zhang@intel.com>
Cc: Ye Ting <ting.ye@intel.com>
Cc: Fu Siyuan <siyuan.fu@intel.com>
Cc: Wu Jiaxin <jiaxin.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Ye Ting <ting.ye@intel.com>
EFI_PAGES_TO_SIZE only handles UINTN, so we use EfiPagesToSize
to handle UINT64.
Cc: Jeff Fan <jeff.fan@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
Regression-tested-by: Laszlo Ersek <lersek@redhat.com>
Cc: Jeff Fan <jeff.fan@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
Regression-tested-by: Laszlo Ersek <lersek@redhat.com>
Current memory attribute table implementation will only mark PE code
to be EfiRuntimeServicesCode, and mark rest to be EfiRuntimeServicesData.
However, there might be a case that a SMM code wants to allocate
EfiRuntimeServicesCode explicitly to let page table protect this region
to be read only. It is unsupported.
This patch enhances the current solution so that MemoryAttributeTable
does not touch non PE image record.
Only the PE image region is forced to be EfiRuntimeServicesCode for
code and EfiRuntimeServicesData for data.
Cc: Jeff Fan <jeff.fan@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
Regression-tested-by: Laszlo Ersek <lersek@redhat.com>
PiSmmCore supports page level protection based upon the Memory Type
(EfiRuntimeServicesCode/EfiRuntimeServicesData) and PE image.
However, the Memory Type information is ignored in AllocatePool().
If a caller calls AllocatePool with EfiRuntimeServicesCode,
the final memory is still allocated as EfiRuntimeServicesData.
This patch supports AllocatePool with EfiRuntimeServicesCode.
Cc: Jeff Fan <jeff.fan@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
Regression-tested-by: Laszlo Ersek <lersek@redhat.com>
Add the comments to describe Free and Allocated SMRAM are added separately.
Cc: Star Zeng <star.zeng@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Port status bits are clear in original code, so no enumeration
takes place.
Changing this to prevent the status bits from being cleared
allows enumeration to proceed normally.
Cc: Star Zeng <star.zeng@intel.com>
Cc: Mike Turner <Michael.Turner@microsoft.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Mike Turner <Michael.Turner@microsoft.com>
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
The commit e27cca has a typo on DEBUG level macro. And this debug
message should be DEBUG_INFO rather than DEBUG_ERROR.
Cc: Jan Dabros <jsd@semihalf.com>
Cc: Marcin Wojtas <mw@semihalf.com>
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
reviewed-by: Marcin Wojtas <mw@semihalf.com>
We add Fmp->GetImage() support in CapsuleApp. So that user may call
Fmp->GetImage() in UEFI shell environment.
This is useful to do unit test for FMP which supports GetImage(),
or user wants to get current image, such as Microcode.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Jeff Fan <jeff.fan@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
EFI_D_INFO, EFI_D_VERBOSE, EFI_D_WARN and EFI_D_ERROR are replaced
with currently recommended values.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jan Dabros <jsd@semihalf.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
* Introduce a generic Debugger Configuration protocol.
* Add private configuration data in the EBC Debugger and make it
register the Debugger Configuration protocol on initialization.
* Add a shell application that uses the protocol above to access
the private data in order to configure the EBC debugger.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Pete Batard <pete@akeo.ie>
reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Make SetPeiServicesTablePointer() earlier than ProcessLibraryConstructorList()
so the constructor() function can get the correct pei service table pointer.
https://bugzilla.tianocore.org/show_bug.cgi?id=238
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Current code is using L'\0' to compare with a ASCII char.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
In function EdbLoadCodBySymbolByIec(), AsciiStrGetNewTokenField() at line
1589 will return NULL if the first character in 'LineBuffer' is '\0'. But
the previous if statement at line 1576 ensures the above case will not
happen.
This commit adds ASSERT as warnings for the case that will not happen.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
In function DebuggerDisplaySymbolAccrodingToAddress(), when variable
'CandidateAddress' (returned by EbdFindSymbolAddress function) equals
(UINTN) -1, it also indicates that the symbol is not found at the given
address.
This commit adds this missing check.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Add checks for the return value of function Atoi() in EdbCmdBreakpoint.c.
If the input parameter 'CommandArg' contains non-digit character, print
corresponding error message.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Operands in a bitwise operation should have the same size to eliminate
unexpected results.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
In current DriverSampleDxe, the sample code of password is
not a good example, so we plan to remove it.
Cc: Liming Gao <liming.gao@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
In current SetupBrowser, the logic related to non-interative password
is not correct. How to support it correctly or whether support it
is still under investigation. First step remove the incorrect logic.
Cc: Liming Gao <liming.gao@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
when the password is not supported, pop up a dialogue
to let user know the reason.
Cc: Liming Gao <liming.gao@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
According to AHCI Spec 1.3 GHC.AE bit description:
"The implementation of this bit is dependent upon the value of the
CAP.SAM bit. If CAP.SAM is '0', then GHC.AE shall be read-write and shall
have a reset value of '0'. If CAP.SAM is '1', then AE shall be read-only
and shall have a reset value of '1'."
Being in AhciMode, for proper operation it is required, that GHC.AE bit
is always set, before any other AHCI registers are written to. Current
AhciMode implementation, both in AhciReset() and AhciModeInitialization()
functions, set GHC.AE bit only depending on 'CAP.SAM == 0' condition,
assuming (according to the AHCI spec), that otherwise it has to be set
anyway. It may however happen, that even if 'CAP.SAM == 1', GHC.AE
requires updating by software.
This patch enables in AhciMode setting GHC.AE in case its initial value
is '0'. It fixes AHCI support for Marvell Armada 70x0 and 80x0 SoC
families. The change is transparent to all other platforms.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Jan Dabros <jsd@semihalf.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
We send ADDRESS DEVICE CMD in XhcInitializeDeviceSlot(), which will
cause XHC issue a USB SET_ADDRESS request to the USB Device.
According to USB spec, there should have a 10ms delay before this
operation after resetting a given port.
But in original code, there is a possible path which may have no such
10ms delay:
UsbHubResetPort()->UsbHubSetPortFeature()->Stall(20)->UsbHubGetPortSt
atus()->XhcPollPortStatusChange()->(if RESET_C bit is set)->
XhcInitializeDeviceSlot()->(if RESET_C bit is set)->Stall(10)
So this patch is used to fix above issue.
Cc: Star Zeng <star.zeng@intel.com>
Cc: Baraneedharan Anbazhagan <anbazhagan@hp.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Tested-by: Baraneedharan Anbazhagan <anbazhagan@hp.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
This patch is used to allow the IPv4 with prefix case.
Cc: Fu Siyuan <siyuan.fu@intel.com>
Cc: Ye Ting <ting.ye@intel.com>
Cc: Zhang Lubo <lubo.zhang@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiaxin Wu <jiaxin.wu@intel.com>
Reviewed-by: Fu Siyuan <siyuan.fu@intel.com>
VM related defs are now in EbcVmTest.h, and opocode related definitions in
Ebc.h.
Because it is used by both the EBC Debugger and driver,
EbcDebugSignalException() sees its definition factorized in
EbcDebuggerHook.h.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Pete Batard <pete@akeo.ie>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
* This patch introduces EbcDebuggerHook.c/h and inserts the required
EBCDebugger references into the existing EBC source files.
* With all the hooks defined to their empty version in EbcDebuggerHook.c
the existing EBC VM behaviour is left unaffected.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Pete Batard <pete@akeo.ie>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
When returning selectable menu, should return the menu in current form,
the codes miss to do the check. Now returning the selectable menu behind
the codes "if ((UINTN) Distance + NextMenuOption->Skip > GapToTop)".
Then can cover the check, can return the menu correctly.
https://bugzilla.tianocore.org/show_bug.cgi?id=232
Cc: Liming Gao <liming.gao@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Function GetVariable2() ensures its third (output) parameter will not be
NULL when the return status is EFI_SUCCESS.
This commit adds ASSERT as warnings for the case that will not happen.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
gSmmCorePrivate->CommunicationBuffer and gSmmCorePrivate->BufferSize locate at
runtime memory region. That means they could be modified by non-SMM code during
runtime.
We should cache them into SMM local variables before we verify them. After
verification, we should use the cached ones directly instead of the ones in
gSmmCorePrivate.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
This patch updates the PXE driver to drop the input DHCP packet if it
exceed the maximum length.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Fu Siyuan <siyuan.fu@intel.com>
Reviewed-By: Wu Jiaxin <jiaxin.wu@intel.com>
Current implementation always creates PlatformRecovery0000
pointing to \EFI\BOOT\BOOT$(ARCH).efi but it may overwrite
PlatformRecovery#### created before (maybe by a DXE driver).
The patch only uses the smallest unused option number for
the \EFI\BOOT\BOOT$(ARCH).efi PlatformRecovery#### to avoid
overwriting already-created PlatformRecovery####.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Jie Lin <jie.lin@intel.com>
Reviewed-by: Sunny Wang <sunnywang@hpe.com>
The implementation doesn't check the LoadOptions[Index].Status but
only depends on the Status returned from
EfiBootManagerProcessLoadOption(), which results only the first
PlatformRecovery#### runs.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Jie Lin <jie.lin@intel.com>
Reviewed-by: Sunny Wang <sunnywang@hpe.com>
Current CpuExceptionHanderLibNull instance returns EFI_SUCCESS for all three
services. If platform does not want to hook the Exception vector for some
modules (For example DxeCore), it could select this NULL instance in DSC file
for those module. But some modules that want to consume
RegisterCpuInterruptHandler() cannot use NULL instance. If platform does not
select the correct library instance, it will does work. But the caller does not
recognize it.
This update is to return EFI_UNSUPPORTED on RegisterCpuInterruptHandler() in
NULL instance instead of return EFI_SUCCESS. Once platform selects this NULL
instance, the caller could know it from return status.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
This table describes the SMM memory attributes.
The new GUID gEdkiiPiSmmMemoryAttributesTableGuid and its associated
structure are based on the EFI_MEMORY_ATTRIBUTES_TABLE and GUID from the
UEFI Specification.
Cc: Jeff Fan <jeff.fan@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
[lersek@redhat.com: update commit message as requested by Michael Kinney]
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
The memory will be set to background color after success allocate
the data, so not need to call AllocateZeroPool.
Related bugz: https://bugzilla.tianocore.org/show_bug.cgi?id=223
Cc: Dandan Bi <dandan.bi@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
The SMM memory attribute table concept is similar to UEFI
memory attribute table.
The new file MdeModulePkg/Core/PiSmmCore/MemoryAttributesTable.c
and the new code in MdeModulePkg/Core/PiSmmCore/Page.c
are based on the algorithms and implementation from
MdeModulePkg/Core/Dxe/Misc/MemoryAttributesTable.c
and MdeModulePkg/Core/Dxe/Mem/Page.c.
These new components are based on the Memory Attributes Table
feature from the UEFI Specification and the existing DXE Core
implementation that supports that feature.
This SMM MemoryAttributes table is produced at SmmEndOfDxe event.
So that the consumer (PiSmmCpu) may consult this table
to set memory attribute in page table.
This patch also installs LoadedImage protocol to SMM
protocol database, so that the SMM image info can be
got easily to construct the PiSmmMemoryAttributes table.
Cc: Jeff Fan <jeff.fan@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Michael D Kinney <michael.d.kinney@intel.com>
This table describes the SMM memory attributes.
Cc: Jeff Fan <jeff.fan@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Michael D Kinney <michael.d.kinney@intel.com>
This patch made the following change:
* DataItem->Status should be updated to the status code.
* Data should not be freed if EFI_NOT_READY returned.
Cc: Santhapur Naveen <naveens@amiindia.co.in>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Ye Ting <ting.ye@intel.com>
Cc: Fu Siyuan <siyuan.fu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiaxin Wu <jiaxin.wu@intel.com>
Reviewed-by: Ye Ting <ting.ye@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
v2:
* Separate out the return status fix.
* Replace IP4_MASK_MAX with IP4_MASK_NUM.
* Remove the ON_EXIT label.
This patch is used to add the wrong/invalid subnet check.
Cc: Santhapur Naveen <naveens@amiindia.co.in>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Ye Ting <ting.ye@intel.com>
Cc: Fu Siyuan <siyuan.fu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiaxin Wu <jiaxin.wu@intel.com>
Reviewed-by: Ye Ting <ting.ye@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
remove EFI_CAPSULE_FROM_FILE_DIR
remove EFI_OS_INDICATIONS_FILE_CAPSULE_DELIVERY_SUPPORTED.
no one uses them.
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Michael D Kinney <michael.d.kinney@intel.com>
This patch is used to revert changes done in commit 17f3e942
bc527fbd75068d2d5752b6af54917487 - "MdeModulePkg/UsbMass: Not
retry if usb bot transfer execution fail"
It's because Usb Floppy will report DEVICE_ERROR for the first
several cmds when it need spin up. so retry logic makes sense.
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
FreePool (Blt) function will be called in while loop, cannot be removed.
Cc: Liming Gao <liming.gao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Bell Song <binx.song@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
The 3rd party image should be loaded after EndOfDxe event signal and
DxeSmmReadyToLock protocol installation. But non-SMM platform doesn't
published DxeSmmReadyToLock protocol.
So the SecurityStubDxe can only depend on EndOfDxe event.
This patch enhances the SecurityStubDxe to listen on
DxeSmmReadyToLock protocol installation and if any 3rd party image
is loaded before DxeSmmReadyToLock, it reports failure.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Sunny Wang <sunnywang@hpe.com>
The patch adds check of deferred images before booting to OS.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Chao B Zhang <chao.b.zhang@intel.com>
Reviewed-by: Sunny Wang <sunnywang@hpe.com>
The API dispatches the deferred images that are returned from all
DeferredImageLoad instances.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Chao B Zhang <chao.b.zhang@intel.com>
Reviewed-by: Sunny Wang <sunnywang@hpe.com>
The images not from FV are treated as 3rd party images. They will
be deferred to dispatch when they are dispatched before EndOfDxe
event.
It's a new feature in the BS.LoadImage() path which can disallow
executing 3rd party images before EndOfDxe and re-execute them
after EndOfDxe (through EfiBootManagerDispatchDeferredImages
introduced in next commit).
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Chao B Zhang <chao.b.zhang@intel.com>
Reviewed-by: Sunny Wang <sunnywang@hpe.com>
When PciSioSerial is firstly started with a non-NULL remaining
device path, the UART instance is created using the parameters
specified in the remaining device path. Later when the driver
is started again on the same UART controller with NULL remaining
device path, the correct logic is to directly return SUCCESS
instead of current buggy implementation which wrongly produces
another UART using the default parameters.
The bug causes two UARTs are created when the UART is configured
in 57600 baud rate.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
PeiServicesAllocatePages () will output sizeof (EFI_PHYSICAL_ADDRESS) value.
IdtTableForX64 is sizeof (UINTN) local variable. It will overwrite other local
variable.
This issue is found when we dump BaseOfStack value.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Cc: Michael Kinney <michael.d.kinney@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Dump new stack base and size information could help developer to narrow down
stack crash issue.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Cc: Michael Kinney <michael.d.kinney@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
According to UFS Host Controller Spec(JESD223), the bits 1:0 of this
DataByteCount field shall be 11b to indicate Dword granularity.
But the size of UFS Request Sense Data Response defined in UFS Spec
(JESD220C) is 18 which is not Dword aligned, we would have to round
down to the multiple of 4 to fill the DBC field to avoid bring issue
on some UFS HCs.
Cc: Hao Wu <hao.a.wu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
The UiApp is updated to consume PcdTestKeyUsed to know if there is any
test key used in current BIOS, such as recovery key,
or capsule update key.
Then UiApp show warning information in front page.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Tested-by: Michael Kinney <michael.d.kinney@intel.com>
This CapsuleApp can help perform capsule update in UEFI shell environment.
It can also dump capsule information, capsule status variable,
ESRT and FMP.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Cc: Chao Zhang <chao.b.zhang@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Tested-by: Michael Kinney <michael.d.kinney@intel.com>
The previous ESRT driver unconditionally treat FMP to be
ESRT_FW_TYPE_DEVICEFIRMWARE.
EDKII System Capsule reuses FMP, but it is ESRT_FW_TYPE_SYSTEMFIRMWARE.
Add check to ImageTypeId check to see if it is ESRT_FW_TYPE_SYSTEMFIRMWARE.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Cc: Chao Zhang <chao.b.zhang@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Tested-by: Michael Kinney <michael.d.kinney@intel.com>
This instance handles Microsoft UX capsule, UEFI defined FMP capsule.
This instance should not assume any capsule image format.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Cc: Chao Zhang <chao.b.zhang@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Tested-by: Michael Kinney <michael.d.kinney@intel.com>
1) Add capsule related library.
FmpAuthenticationLib
2) Add capsule related status code PCD.
PcdStatusCodeSubClassCapsule
PcdCapsuleStatusCodeProcessCapsulesBegin
PcdCapsuleStatusCodeProcessCapsulesEnd
PcdCapsuleStatusCodeUpdatingFirmware
PcdCapsuleStatusCodeUpdateFirmwareSuccess
PcdCapsuleStatusCodeUpdateFirmwareFailed
PcdCapsuleStatusCodeResettingSystem
3) Add capsule status variable PCD - CapsuleMax value.
PcdCapsuleMax
4) Add system FMP indicator PCD - used by ESRT.
PcdSystemFmpCapsuleImageTypeIdGuid
5) Add PcdTestKeyUsed PCD.
This PCD can be set by platform to indicate if there is any
test key used in current BIOS, such as recovery key,
or capsule update key.
Then the generic UI may consume this PCD to show warning information.
Other platform driver may also consume this PCD to know such info,
and report it via platform specific way.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Cc: Chao Zhang <chao.b.zhang@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Tested-by: Michael Kinney <michael.d.kinney@intel.com>
ProcessCapsules() API can be used by platform BDS to process all capsules.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Cc: Chao Zhang <chao.b.zhang@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Tested-by: Michael Kinney <michael.d.kinney@intel.com>
This library is used to authenticate a UEFI defined FMP Capsule.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Cc: Chao Zhang <chao.b.zhang@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Tested-by: Michael Kinney <michael.d.kinney@intel.com>
If there are two DynamicEx PCDs have the same PCD token number but
in different PCD token spaces, the PcdGetNextToken function may get
the wrong PCD token.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Cinnamon Shia <cinnamon.shia@hpe.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Short Packet case is a normal case, we shouldn't print it as an error
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
AhciDumpPortStatus doesn't fully populate all the fields of
AtaStatusBlock after completing command execution, which may bring
issue if someone depends on the return status.
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
The classful addressing (IP class A/B/C) has been deprecated according to
RFC4632. This patch updates the NetLib NetGetIpClass() and NetIp4IsUnicast()
accordingly.
NetGetIpClass()
The function is kept for compatibility, while the caller of this function
could only check the returned value against with IP4_ADDR_CLASSD (multicast)
or IP4_ADDR_CLASSE (reserved) now. The function has been updated to note this.
NetIp4IsUnicast()
The NetMask becomes a required parameter to check the unicast address.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Fu Siyuan <siyuan.fu@intel.com>
Reviewed-by: Ye Ting <ting.ye@intel.com>
Reviewed-by: Wu Jiaxin <jiaxin.wu@intel.com>
https://bugzilla.tianocore.org/show_bug.cgi?id=190
The issue is with signed/unsigned comparisons between
Mode->CursorRow and Row and Mode->CursorColumn and Column.
The fix is to add typecast to UINTN for comparisons.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Brian Johnson <bjohnson@sgi.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Michael Kinney <michael.d.kinney@intel.com>
Reviewed-by: Brian Johnson <bjohnson@sgi.com>
In one of the next patches, we'll introduce ARRAY_SIZE in
"MdePkg/Include/Base.h". In order to proceed in small steps, make the
module-local definition of ARRAY_SIZE conditional. This way the
introduction of the macro under MdePkg will silently switch this module
over (after which we can remove the module-local definition completely).
Cc: Cecil Sheng <cecil.sheng@hpe.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Feng Tian <feng.tian@Intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
The TtyTerm terminal driver is missing support for sequences produced
by the page up, page down, insert, home, and end keys in some terimnal
emulators. Add them.
Tested under Ubuntu 16.04 using xterm 322-1ubuntu1, GNOME terminal
3.18.3-1ubuntu1, and XFCE terminal 0.6.3-2ubuntu1.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Kyle Roberts <kyroberts@sgi.com>
Signed-off-by: Brian Johnson <bjohnson@sgi.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Reviewed-by: Roy Franz <roy.franz@hpe.com>
Tested-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Feng Tian <feng.tian@intel.com>
For TtyTerm terminals, output a shorter escape sequence when possible
to move the cursor within the current line, and don't print any escape
sequence if the cursor is already at the correct position. This
removes extra cursor motion activity at the EFI shell prompt,
improving performance. It also makes it possible in many cases to
successfully use a terminal window which is taller than the driver's
mode setting (eg. 80x25.)
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Brian Johnson <bjohnson@sgi.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Tested-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Feng Tian <feng.tian@intel.com>
When we print the last character on a line, the terminal driver wraps
CursorRow/CursorColumn to the beginning of the next line. But the
terminal itself doesn't wrap its cursor until the next character is
printed. That throws off the driver's cursor position tracking.
So when we have printed the last character on a line, and are not in
the middle of outputing an escape sequence, synchronize the terminal
with the driver by outputing CR+LF. This matches the expected
behavior, and the behavior of the VGA console driver.
Only change the behavior of TtyTerm, not the other terminal types.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Brian Johnson <bjohnson@sgi.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Tested-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Feng Tian <feng.tian@intel.com>
The function which handles the "Boot####", "BootOrder" ...
may return failure. This patch adds the error handling codes.
return the failure info to browser.
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Liming Gao <liming.gao@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
When user enter the "Change Boot Order" page, the BootOptionOrder in
BmmFakeNvData may maintain some uncommitted data which are not saved
in "BootOrder" Variable and BootOptionMenu. So we should not always get
the BootOptionOrder through the function GetBootOrder, it will
result in incorrect UI behaviors. When the BootOptionOrder has not been
saved, we should use the BootOptionOrder in current BmmFakeNvData.
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Liming Gao <liming.gao@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
In BootMaintRouteConfig function, it will compare the data in BmmFakeNvData
and BmmOldFakeNVData to see whether there are some changes need to save.
In current codes when discarding changes or removing the useless changes,
it will update the related fields in BmmFakeNvData.
But also need to update related fields in BmmOldFakeNVData,
or it will result in incorrect comparison in BootMaintRouteConfig function,
then resulting in incorrect UI behaviors.
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Liming Gao <liming.gao@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
When updating console page, the "ConsoleCheck" in BmmFakeNvData may maintain
the old uncommitted data, we should not copy it to BmmOldFakeNVData.
And in BootMaintRouteConfig function, when save data successfully,
it will copy the BmmFakeNvData to the BmmOldFakeNVData.
So we can delete the logic here.
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Liming Gao <liming.gao@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
In current codes, When user does some change related to Console or Terminal,
when saving data, it will update the content in TerminalMenu and ConsoleMenu
in BootMaintRouteConfig function. This patch moves the update action to the
BootMaintCallback function with EFI_BROWSER_ACTION_CHANGED type.
The reason for this change is: in BootMaintRouteConfig function when
Var_UpdateConsoleXXXOption() return failure and user discard the previous
change, we should re_update the content in the TerminalMenu and ConsoleMenu.
So we move the update action to the changed callback.
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Liming Gao <liming.gao@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
When fail to submit data and user discard the change, we should send
the discard info to driver with EFI_BROWSER_ACTION_CHANGED callback.
Cc: Liming Gao <liming.gao@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
In function 'LibAppendFileName' of 'FileExplorer.c':
"
MaxLen = (Size1 + Size2 + sizeof (CHAR16))/ sizeof (CHAR16);
"
Overflow may happen here. MaxLen might become a very small number.
This patch adds integer overflow checker.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
When PciBus is built as EBC, PcdPciDegradeResourceForOptionRom does
not have associated value resulting build failure.
The patch sets the default value to TRUE, covering the EBC ARCH.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Feng Tian <feng.tian@intel.com>
The driver uses the GraphicsInfo HOB and GraphicsDeviceInfo HOB
passed from PEI to find the graphics controller to manage and
produce the GraphicsOutput protocol.
GraphicsInfo HOB and GraphicsDeviceInfo HOB are created by
a PEIM which initializes the graphics controller hardware in
PEI phase.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
This PCD is used to indicated the recovery file name.
The previous name - FvMain.Fv is hardcoded in CdExpressPei.
It does not make sense to force the name.
Now a platform may use any recovery file name.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Michael D Kinney <michael.d.kinney@intel.com>
This PCD is used to indicated the recovery file name.
The previous name - FvMain.Fv is hardcoded in FatPei and CdExpressPei.
It does not make sense to force the name.
Now a platform may use any recovery file name.
Tested-by: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Michael D Kinney <michael.d.kinney@intel.com>
Tcp driver need to use EFI_D_NET to log DEBUG message,
So it becomes easy to separate/filter out debug messages
from network stack versus generic EFI_D_INFO debugs.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Zhang Lubo <lubo.zhang@intel.com>
Cc: Hegde Nagaraj P <nagaraj-p.hegde@hpe.com>
Cc: Subramanian Sriram <sriram-s@hpe.com>
Cc: Fu Siyuan <siyuan.fu@intel.com>
Cc: Ye Ting <ting.ye@intel.com>
Reviewed-by: Sriram Subramanian <sriram-s@hpe.com>
The return value of GetImageIdOrAddress() could be NULL if the
ImageId is invalid. The patch fixes the bug to return EFI_NOT_FOUND
when GetImageIdOrAddress() returns NULL.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
The type of variable "SmallestIdFromFlag" should be BOOLEAN,
this patch fix the incorrect type.
Cc: Liming Gao <liming.gao@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Current PeiCdExpress driver will return capsule size to
be block aligned.
It will fail if we check the capsuleImageSize field.
The patch correct the returned capsule size.
Tested-by: Eric Dong <eric.dong@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
The two libraries are created to support old BootLogoLib to
decode the images. Due to the new BootLogoLib starts using
HiiImageEx interfaces, the two libraries are not needed.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
LogoDxe embeds the image resource in the PE resource section, then
it produces Platform Logo protocol which can return the images
in pixel format.
HiiImageEx protocol is responsible to decode the JPEG/PNG images
to pixel format. LogoDxe driver uses HiiImageEx protocol.
Contributed-under: TianoCore Contribution Agreement 1.0
Reviewed-by: Liming Gao <liming.gao@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Dandan Bi <dandan.bi@intel.com>
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
1. Change PlatformLogo protocol to return EFI_IMAGE_INPUT instead of
RAW image data. PlatformLogo implementation can use HiiImageEx to
decode the image if it's JPEG or PNG format.
2. Change BootLogoLib to consume the new PlatformLogo protocol.
3. Change BootLogoEnableLogo() to only use images returned from
PlatformLogo protocol.
Contributed-under: TianoCore Contribution Agreement 1.0
Reviewed-by: Liming Gao <liming.gao@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Dandan Bi <dandan.bi@intel.com>
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
According to UEFI spec, NewImageEx()/SetImageEx()/DrawImageEx()
implicitly call the non-Ex version interface
of HiiImage protocol.
GetImageEx()/DrawImageIdEx() are the enhanced version of
GetImage()/DrawImageId(), which can support decoding JPEG/PNG
through the help of HiiImageDecoder protocol.
Contributed-under: TianoCore Contribution Agreement 1.0
Reviewed-by: Liming Gao <liming.gao@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Dandan Bi <dandan.bi@intel.com>
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
1. Update GetImageIdOrAddress() to recognize PNG/JPEG image block.
A offset calculation bug was fixed.
2. Update HiiGetImage() comments to say PNG/JPEG support is provided
by HiiImageEx
3. Update HiiSetImage() to support replacing a PNG/JPEG image block
with a new image
Contributed-under: TianoCore Contribution Agreement 1.0
Reviewed-by: Liming Gao <liming.gao@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Dandan Bi <dandan.bi@intel.com>
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
The previous DNS server data will be retained after the policy
changes from Dhcp to Static. This patch is used to clean the
previous dhcp configuration data.
Cc: Hegde Nagaraj P <nagaraj-p.hegde@hpe.com>
Cc: Subramanian Sriram <sriram-s@hpe.com>
Cc: Ye Ting <ting.ye@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiaxin Wu <jiaxin.wu@intel.com>
Reviewed-by: Sriram Subramanian <sriram-s@hpe.com>
Reviewed-by: Hegde Nagaraj P <nagaraj-p.hegde@hpe.com>
Tested-by: Hegde Nagaraj P <nagaraj-p.hegde@hpe.com>
The 'universal' PCI bus driver in MdeModulePkg contains a quirk to
degrade 64-bit PCI MMIO BARs to 32-bit in the presence of an option
ROM on the same PCI controller.
This quirk is highly specific to not just the X64 architecture in general,
but to the PC platform in particular, given that only X64 platforms that
require legacy PC BIOS compatibility require it. However, making the
quirk dependent on the presence of the legacy BIOS protocol met with
resistance, due to the fact that it introduces a dependency on the
IntelFrameworkModulePkg package.
So instead, make the quirk configurable, by introducing a feature flag PCD
'PcdPciDegradeResourceForOptionRom' which defaults to TRUE only for X64.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Some XHCI host controllers require to have extra 1ms delay before
accessing any MMIO register during HC reset.
As this delay is not defined by XHCI spec, we use this workaround
to fix the issue.
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Some XHCI host controllers require to have extra 1ms delay before
accessing any MMIO register during HC reset.
As this delay is not defined by XHCI spec, we use this workaround
to fix the issue.
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
To follow PI1.4a, BaseTools has be updated to fix artificial limitation of
SkuId range.
This patch is to update PCD database structure definition to match BaseTools.
Note: The source code and BaseTools need to be upgraded at the same time,
and if they are not upgraded at the same time, build error like below will
be triggered to help user identify the problem.
"Please make sure the version of PCD PEIM Service and the generated
PCD PEI Database match."
Cc: Liming Gao <liming.gao@intel.com>
Cc: Yonghong Zhu <yonghong.zhu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
This patch is to fix the incorrect logic when handling the "&READONLY" tag
in <KeywordResp>.
1. In UEFI spec, the "&READONLY" tag is in upper case, but using the lower
case in current codes by mistake.
2. The logic in checking the ReadOnly flag is not correct. Whether having
"&READONLY" tag must be consistent with the result of
"ExtractReadOnlyFromOpCode" function.
Cc: Liming Gao <liming.gao@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
For a question, its question id can not be zero.
This patch is to fix the issue that using zero as question id.
Cc: Liming Gao <liming.gao@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Currently, the EFI_PCI_ATTRIBUTE_DUAL_ADDRESS_CYCLE attribute is completely
ignored by the PCI host bridge driver, which means that, on an implementation
that supports DMA above 4 GB, allocations above 4 GB may be provided to
devices that have not expressed support for it.
So in addition to checking 'RootBridge->DmaAbove4G' to establish whether the
root bridge itself supports DMA above 4 GB, we must also take into account
the operation type (EfiPciOperationBusMaster{Read|Write|CommonBuffer}64),
and the EFI_PCI_ATTRIBUTE_DUAL_ADDRESS_CYCLE attribute, when mapping and
allocating DMA memory, respectively.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Ruiyu Ni <Ruiyu.ni@intel.com>
The IP address should not be treated as classful one if DHCP options
contain a classless IP with its true subnet mask. Otherwise, DHCPv4
TransmitReceive() will failed. This real subnet mask will be parsed
and recorded in DhcpSb->Netmask. So, we need check it before get the
IP's corresponding subnet mask.
Cc: Santhapur Naveen <naveens@amiindia.co.in>
Cc: Ye Ting <ting.ye@intel.com>
Cc: Fu Siyuan <siyuan.fu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiaxin Wu <jiaxin.wu@intel.com>
Reviewed-by: Fu Siyuan <siyuan.fu@intel.com>
Since current codes in NvmExpressDxe already support the non-blocking I/O
feature for EFI_NVM_EXPRESS_PASS_THRU_PROTOCOL interface, the relative bit
in the 'Attributes' field of EFI_NVM_EXPRESS_PASS_THRU_MODE should be set
to reflect this.
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
This commit fixes the issue that the caller event passed to
EFI_NVM_EXPRESS_PASS_THRU_PROTOCOL.PassThru() will not be signaled for
NVME Admin commands.
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
According to the UEFI spec, EFI_NVM_EXPRESS_PASS_THRU_PROTOCOL.PassThru()
should return EFI_INVALID_PARAMETER if the input 'NamespaceId' is invalid
for the NVM Express controller. This commit adds check in PassThru() to
follow this rule.
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
This commit adds serveral checks for the 'Packet' parameter passed to the
EFI_NVM_EXPRESS_PASS_THRU_PROTOCOL.PassThru() API:
The check for the 'TransferLength' field in
EFI_NVM_EXPRESS_PASS_THRU_COMMAND_PACKET to make sure the value will not
exceed the maximum data transfer size allowed by a controller.
The check for the 'TransferBuffer' and 'TransferLength' fields in
EFI_NVM_EXPRESS_PASS_THRU_COMMAND_PACKET when the Opcode of an NVME
command indicates a data transfer between controller and host.
The check for the 'MetadataLength' field in
EFI_NVM_EXPRESS_PASS_THRU_COMMAND_PACKET to make sure the value is not 0
when the corresponding 'MetadataBuffer' field has a non-NULL value.
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
According to UEFI spec, an EFI_NVM_EXPRESS_PASS_THRU_PROTOCOL with neither
EFI_NVM_EXPRESS_PASS_THRU_ATTRIBUTES_LOGICAL nor
EFI_NVM_EXPRESS_PASS_THRU_ATTRIBUTES_PHYSICAL set in the Attributes field
is an illegal configuration.
This commit adds this check in the PassThru API to follow the spec.
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
According to the UEFI spec, the 'TransferBuffer' and 'MetadataBuffer' used
in a data transfer should be aligned on the boundary specified by the
IoAlign field in the EFI_NVM_EXPRESS_PASS_THRU_MODE structure.
This commit adds this check to follow the spec.
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
According to the UEFI spec,
EFI_NVM_EXPRESS_PASS_THRU_PROTOCOL.GetNextNamespace() should return
EFI_NOT_FOUND when the value pointed to by NamespaceId is the namespace ID
of the last namespace on the NVM Express controller. This commit modifies
the check for NamespaceId to follow this rule.
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
According to the UEFI spec,
EFI_NVM_EXPRESS_PASS_THRU_PROTOCOL.GetNamespace() should return
EFI_NOT_FOUND when the input DevicePath is a device path node type that
the NVM Express Pass Thru driver supports, but there is not a valid
translation from DevicePath to a namespace ID. Current code will return
EFI_SUCCESS. This commit adds additional check in the GetNameSpace API to
make sure correct status is returned.
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
According to the UEFI spec,
EFI_NVM_EXPRESS_PASS_THRU_PROTOCOL.BuildDevicePath() should return
EFI_NOT_FOUND when the input NamespaceId is not valid. However, current
code returns EFI_DEVICE_ERROR instead. This commit modifies the check for
input NamespaceId to return the correct status.
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
The gBS->OpenProtocol() calls to open EFI_NVM_EXPRESS_PASS_THRU_PROTOCOL
in NvmExpress.c will crash the data in 'Mode' field of
'Private->Passthru'.
The third parameter of gBS->OpenProtocol() is an output parameter that
stores the address where a pointer to the corresponding Protocol
Interface. The current code mistakenly pass '&Private->Passthru' (a
pointer of the EFI_NVM_EXPRESS_PASS_THRU_PROTOCOL) as the third
parameter. This will crash the data in 'Mode' filed.
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Support multiple PCI segment for PCI_CONFIG2 opcodes.
PiDxeS3BootScriptLib needs to be updated to consume PciSegmentLib
instead of PciLib. That means platforms need to add PciSegmentLib
declaration like below in platform dsc if the PciSegmentLib was
not declared in platform dsc before.
PciSegmentLib|MdePkg/Library/BasePciSegmentLibPci/BasePciSegmentLibPci.inf
For platforms only have one segment,
MdePkg/Library/BasePciSegmentLibPci/BasePciSegmentLibPci.inf is recommended
to be used and declared in platform dsc for PiDxeS3BootScriptLib to have
equivalent functionality with before.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Amy Chan <amy.chan@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
BootManagerMenu boot option is handled by EfiBootManagerGetBootManagerMenu.
Don't need to handle it again when parse LoadFile protocol.
In V2, use "BootManagerMenu" instead of "BootMenuApp".
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Sunny Wang <sunnywang@hpe.com>
Rename local function name BootMenuApp to BootManagerMenu to align to
other public function name.
In V2, use "BootManagerMenu" instead of "BootMenuApp".
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Sunny Wang <sunnywang@hpe.com>
The prototypes of EbcInterpret() and ExecuteEbcImageEntryPoint() are
private to the AARCH64 implementation of EbcDxe, so we can shuffle
the arguments around a bit and make the assembler thunking glue a lot
simpler.
For ExecuteEbcImageEntryPoint(), this involves passing the EntryPoint
argument as the third parameter, rather than the first, which allows
us to do a tail call. For EbcInterpret(), instead of copying each
argument beyond #8 from one native stack frame to the next (before
another copy is made into the VM stack), pass a pointer to the
argument stack.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Instead of pessimistically copying at least 64 bytes from the VM stack
to the native stack, and popping off the register arguments again
before doing the native call, try to avoid touching the stack completely
if the VM stack frame is <= 64 bytes. Also, if the stack frame does exceed
64 bytes, there is no need to copy the first 64 bytes, since we are passing
those in registers anyway.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Reviewed-by: Feng Tian <feng.tian@intel.com>
The thunk generation is needlessly complex, given that it attempts to
deal with variable length instructions, which don't exist on AArch64.
So replace it with a simple template coded in assembler, with a matching
struct definition in C. That way, we can create and manipulate the thunks
easily without looping over the instructions looking for 'magic' numbers.
Also, use x16 rather than x9, since it is the architectural register to
use for thunks/veneers.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Change to consistent // style comments. Also, remove bogus global
definitions for external functions, and move the real exports to
the top of the file.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Reviewed-by: Feng Tian <feng.tian@intel.com>
UEFI spec:
Each load option entry resides in a Boot####, Driver####, SysPrep####,
OsRecovery#### or PlatformRecovery#### variable where #### is replaced
by a unique option number in printable hexadecimal representation using
the digits 0-9, and the upper case versions of the characters A-F
(0000-FFFF).
The patch also makes L"HwErrRec####" follow this rule.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Instead of comparing a GUID with gZeroGuid via the CompareGuid API, the
commit uses the IsZeroGuid API to check if the given GUID is a zero GUID.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@Intel.com>
If a FQDN contains 3 dots '.' like "a.b.c.com", the AsciiStrToIp4
will return success as the HostName has a valid IP address. So we
need to check if it is a decimal character before using AsciiStrDecimalToUintn.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Zhang Lubo <lubo.zhang@intel.com>
Reviewed-by: Fu Siyuan <siyuan.fu@intel.com>
Reviewed-by: Ye Ting <ting.ye@intel.com>
Reviewed-by: Sriram Subramanian <sriram-s@hpe.com>
We have added a new policy to get default value for question:
get default from other default id if current default is not specified.
But when getting default value for checkbox, if the default
flag is not set, it will set the default value to FALSE for checkbox.
This behavior in checkbox conflicts with the new added policy,
so now we move this behavior to the end of getting default form other
default id.
Cc: Liming Gao <liming.gao@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
IpSb->Reconfig should not be set to TRUE to focal the reconfiguration
during the policy changes from Static to DHCP. It's redundancy because
the default router table and default addresses have been freed ahead (
Detailed see Ip4Config2OnPolicyChanged() function). Otherwise, the
potential failure will appear if UseDefaultAddress configured. Reproduce
steps see below:
#1. Set policy to DHCP.
#2. If DHCP process is not complete yet, then run one APP to invoke UDP4
Configure with "UseDefaultAddress = TRUE" (loop to call UDP4 Configure
until Ip4Mode.IsConfigured changes to TRUE).
#3. Even DHCP succeed but Ip4Mode.IsConfigured flag never set to TRUE
Concrete analysis is as follows:
In #1, the policy will be set to DHCP, and then Ip4Config2OnPolicyChanged()
will be called. In this function, if "IpSb->Reconfig" flag is set to TRUE,
the original "IpSb->DefaultInterface" will be abandoned/freed once the
DHCP process finished.
In #2, UDP4 Configure with "UseDefaultAddress = TRUE" is called, that means
the default interface (IpSb->DefaultInterface) will be selected as current
instance's interface.
In #3, when DHCP process finished, the original DefaultInterface will be
abandoned/freed because "IpSb->Reconfig" flag is true. Meanwhile, one new
interface is assigned to "IpSb->DefaultInterface". This new interface is
different to the original one assigned to the UDP4 Configured instance. So,
even DHCP process succeed, the up caller will never have the chance to get
it's truly status.
Cc: Cohen Eugene <eugene@hp.com>
Cc: Ye Ting <ting.ye@intel.com>
Cc: Fu Siyuan <siyuan.fu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiaxin Wu <jiaxin.wu@intel.com>
Tested-by: Eugene Cohen <eugene@hp.com>
Reviewed-by: Ye Ting <ting.ye@intel.com>
The RSDT is only used when the bios need to support ACPI 1.0
version. When change PcdAcpiExposedTableVersions to 0x3C, it
will not support ACPI 1.0. The default is 0x3E.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Zhang Lubo <lubo.zhang@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Ye Ting <ting.ye@intel.com>
Cc: Fu Siyuan <siyuan.fu@intel.com>
Reviewed-by: Ye Ting <ting.ye@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
This patch is to enhance SetupBrowser to handle following two cases:
1. When searching BlockName in AltResp, the hex digits of related BlockName
in AltResp may be in uppercase.
2. When converting the Value in AltResp to HiiValue, the length of value
string is bigger than the length of StorageWidth of the question.
Cc: Liming Gao <liming.gao@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
When comparing the L"OFFSET=" with the ConfigResp string to find
all the "OFFSET=" in ConfigResp, should skip the character "&"
before "OFFSET=" in ConfigResp string.
Cc: Liming Gao <liming.gao@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Add a new implementation policy of getting default value in SetupBrowser.
The new policy is only for the situation that a question has default
value but doesn't have default value for all supported default type.
In this case, we will choose the smallest default id from the existing
defaults, and share its value to other default id which has no
default value.
Cc: Liming Gao <liming.gao@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Add a new implementation policy of getting default value in HiiDatabase.
The new policy is only for the situation that a question has default
value but doesn't have default value for all supported default type.
In this case, we will choose the smallest default id from the existing
defaults, and share its value to other default id which has no
default value.
Cc: Liming Gao <liming.gao@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Add the following definition in the [BuildOptions] section in package DSC
files to disable APIs that are deprecated:
[BuildOptions]
*_*_*_CC_FLAGS = -D DISABLE_NEW_DEPRECATED_INTERFACES
Cc: Feng Tian <feng.tian@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Feng Tian <feng.tian@Intel.com>
The retry mechanism will bring issue if the usb device is unplugged
from XHCI HC but s/w is trying to access it through BlockIo. The
current cmd will get device error return status, but the sequential
cmds will be timeout. This behavior will cause system unresponsive
for a long while and bring bad user experience.
So we break the retry loop if found device error.
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
The original code will assert when dealing with those empty FVs.
The fix is used to solve this bug.
Cc: Chao Zhang <chao.b.zhang@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Chao Zhang <chao.b.zhang@intel.com>
This driver searches APPLICATION in FV and installs LoadFile protocol
for every found one. Then, BDS will add BootOption for LoadFile protocol.
It provides the generic way to expose boot option for the internal
application, such as Shell. With this driver, PlatformBds doesn?t need
to specially handle Shell application.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Update boot description to support LoadFile protocol based on FV file.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
New LoadFileOnFv2 driver will install LoadFile protocol based on FV file.
Update UefiBootManagerLib to find BootMenuApp with LoadFile protocol.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
This function abstracts the common logic to find BootMenuApp file.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
The last TRB in transfer ring is a LINK type TRB, which shouldn't
be accounted as a valid item in IsAsyncIntTrb().
Without this fix, the original algo will bring issue on those URBs
whose TRBs crosses the transfer ring.
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
This change is used to remove the port status polling in port reset
functions.
Why it's needed is because:
1) The same polling on same port has taken place prior to this removed
one. See UsbEnumeratePort()->GetPortStatus(). So this polling in
UsbEnumerateNewDev()->ResetPort() is redundant.
2) EDKII Xhci driver hooks all GetPortStatus() operations. If we don't
remove this one, XHCI driver's XhcPollPortStatusChange() may enter twice
in reset process and wrongly think the device is unplugged.
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
The Host Controller reset has been done at EDKII UHCI/EHCI/XHCI, The
original code will do twice host controller initialization which is
unnecessary. It also bring issues on some USB HCs.
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
This commit will scan all the EFI raw section instances within the
module's FV to make sure the NVDIMM root device SSDT can be properly
located.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Zhang Chao B <chao.b.zhang@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Chao Zhang <chao.b.zhang@intel.com>
> cc1: warnings being treated as errors
> MdeModulePkg/Bus/Pci/PciHostBridgeDxe/PciHostBridge.c:
> In function 'GetProposedResources':
> MdeModulePkg/Bus/Pci/PciHostBridgeDxe/PciHostBridge.c:1388:
> error: integer constant is too large for 'long' type
Append a ULL suffix to the replacement text of PCI_RESOURCE_LESS that is
aligned with the style of the EFI_RESOURCE_SATISFIED and
EFI_RESOURCE_NOT_SATISFIED macros.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Consider the situation as shown in below chart. The last ACK message has
acknowledged the Tcb->RcvWl2, and all the segments until Tcb->RcvNxt have
been received by TCP driver. The Tcb->RcvNxt is not acknowledged due to the
delayed ACK. In this case an incoming segment (Seg->Seq, Seg->End) should
not be accepted by TCP driver, and an immediate ACK is required.
Current TcpSeqAcceptable() thought it’s an acceptable segment incorrectly, it
continues the TcpInput() process instead of sending out an ACK and droping the
segment immediately.
Tcb->RcvWl2 Tcb->RcvNxt Tcb->RcvWl2 + Tcb->RcvWnd
Seg->Seq Seg->End | |
| | | | |
---+-----+---------------+-------------+--------------------------+-----------
<income segment> <----Acceptable Range--- -->
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Fu Siyuan <siyuan.fu@intel.com>
Reviewed-By: Eugene Cohen <eugene@hp.com>
Reviewed-By: Wu Jiaxin <jiaxin.wu@intel.com>
Reviewed-By: Ye Ting <ting.ye@intel.com>
Section 7.8.2 of the PCI Express specification (r4.0 v0.3), entitled "PCI
Express Capabilities Register (Offset 02h)", and section 7.8.9 "Slot
Capabilities Register (Offset 14h)" of the same, describe the conditions
when a PCIe port should be considered "supporting hotplug":
- it should be a root complex port or a switch downstream port, and
- it should have the "Slot Implemented" bit set in the Express
Capabilities Register, and
- it should have the "Hot-Plug Capable" bit set in the Slot Capabilities
Register.
The first two sub-conditions are already implemented in at least two open
source projects I could find:
- in SeaBIOS by Marcel Apfelbaum: "hw/pci: reserve IO and mem for pci
express downstream ports with no devices attached"
<https://code.coreboot.org/p/seabios/source/commit/3aa31d7d6375>,
- in edk2 itself, in the implementation of the "PCI" UEFI Shell command:
see the "PcieExplainTypeSlot" case label in function
PciExplainPciExpress(), file
"ShellPkg/Library/UefiShellDebug1CommandsLib/Pci.c".
PciBusDxe recognizes such PCIe ports as bridges, but it doesn't realize
they support hotplug. In turn PciBusDxe omits getting any resource padding
information from the platform's EFI_PCI_HOT_PLUG_INIT_PROTOCOL for these
bridges:
GatherPpbInfo() [PciEnumeratorSupport.c]
GetResourcePaddingPpb() [PciResourceSupport.c]
GetResourcePaddingForHpb() [PciHotPlugSupport.c]
IsPciHotPlugBus() [PciHotPlugSupport.c]
//
// returns FALSE
//
//
// the following is not reached:
//
gPciHotPlugInit->GetResourcePadding()
Implement a function called SupportsPcieHotplug() for identifying such
ports, and call it from IsPciHotPlugBus() (after the call to IsSHPC()).
Cc: "Johnson, Brian J." <bjohnson@sgi.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Andrew Fish <afish@apple.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Marcel Apfelbaum <marcel@redhat.com>
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ruiyu Ni <Ruiyu.ni@intel.com>
The PCI Hot Plug capability register block is marked with capability ID
0x0C (EFI_PCI_CAPABILITY_ID_SHPC), not 0x06
(EFI_PCI_CAPABILITY_ID_HOTPLUG).
This bug prevents PciBusDxe from recognizing whether a PCI-to-PCI bridge
supports hotplug. In turn the platform's EFI_PCI_HOT_PLUG_INIT_PROTOCOL is
not consulted for resource padding information:
GatherPpbInfo() [PciEnumeratorSupport.c]
GetResourcePaddingPpb() [PciResourceSupport.c]
GetResourcePaddingForHpb() [PciHotPlugSupport.c]
IsPciHotPlugBus() [PciHotPlugSupport.c]
IsSHPC() [PciHotPlugSupport.c]
//
// returns FALSE
//
//
// the following is not reached:
//
gPciHotPlugInit->GetResourcePadding()
Look for the correct capability ID.
Cc: "Johnson, Brian J." <bjohnson@sgi.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Andrew Fish <afish@apple.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Marcel Apfelbaum <marcel@redhat.com>
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ruiyu Ni <Ruiyu.ni@intel.com>
If there is no port multiplier (PortMultiplierPort = 0xFFFF), current code
in functions TransferAtaDevice() and TrustTransferAtaDevice() will always
set the DEV bit of the ATA device register. It causes that ATA commands
cannot be sent to some ATA hard drives.
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Code logic ensures that the pointer 'DriverInfoData' will not be NULL when
it is used.
Add ASSERT as warning for case that will not happen.
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
- abstrated to abstracted
- accessibla to accessible
- addres to address
- apropriate to appropriate
- arry to array
- availabe to available
- avaliable to available
- becasue to because
- correponding to corresponding
- etablished to established
- exeuction to execution
- extensiable to extensible
- fileds to fields
- loadding to loading
- ptototypes to prototypes
- prococol protocol
- requried to required
- resoruce to resource
- runing to running
- uild to build
Cc: Star Zeng <star.zeng@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Giri P Mudusuru <giri.p.mudusuru@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
The commit makes sure that the elements in array 'SwitchResp' get
initialized before being used.
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
At 94092aa603, we extended
MEMORY_PROFILE_ALLOC_INFO to add ActionStringOffset and
Reserved2[6] fields, that was not aware the Reserved[4]
field can be reused to have better memory profile database
size efficiency.
With the patch, PcdMemoryProfilePropertyMask|0x3 and
PcdMemoryProfileMemoryType|0xffff, the memory profile
database size can be reduced as below on my sample platform.
UefiMemoryProfileSize - 0x1597A8 -> UefiMemoryProfileSize - 0x12AB28
SmramProfileSize - 0xCF68 -> SmramProfileSize - 0xB8E8
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Switch all users of ArmLib that depend on the MMU routines to the new,
separate ArmMmuLib. This needs to occur in one go, since the MMU
routines are removed from ArmLib build at the same time, to prevent
conflicting symbols.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
BootMaintenanceManagerUiLib depend on the LeagcyBootMaintUiLib to show the
legacy menus. So we need to do the actions related to LegacyUi in BMM
after the LeagcyBootMaintUiLib have been initialized. So now : 1). update
menus (including legacy menus), 2) re-scan boot options (including legacy
boot option) when opening the BMM form. We think when opening BMM form,
the LeagcyBootMaintUiLib must have been initialized.
Cc: Liming Gao <liming.gao@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
HiiConfigRoutingRouteConfig function returns 'Progress' to indicate
the failure info in the ConfigResp string. But when fail to route the
ConfigResp for EfiVarStore, it doesn't return the correct failure info.
Now this patch is to fix this issue and add debug info let user know the
reason of failure.
Cc: Liming Gao <liming.gao@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Chao Zhang <chao.b.zhang@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Chao Zhang <chao.b.zhang@intel.com>
The patch re-orders the sequences by putting updating memory type
information before loading the boot option so that the reserved
memory usage by HTTP RAM disk boot can be excluded by the memory
type information updating.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Sunny Wang <sunnywang@hpe.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
IP4_CONFIG2_INSTANCE->DataItem is used to save the configuration
data to NV variable. When the policy is changed from static to
DHCP, DnsServers info will be cleaned from DataItem first
(See Ip4Config2SetPolicy), it's correct because DnsServers info
should not be saved to NV variable.
But if there is any DnsServers info received from DHCP message, it
will be reset to DataItem again (See Ip4Config2SetDnsServerWorker),
which may cause the NV variable contain the DnsServers info while
the policy is DHCP (See Ip4Config2WriteConfigData).
Then, while the platform is reset, the issue happened. Because
Ip4Config2DataTypeDnsServer is set under DHCP policy, which is not
allowed by UEFI Spec and error returned.
This patch is used to resolve this potential issue.
Cc: Ye Ting <ting.ye@intel.com>
Cc: Fu Siyuan <siyuan.fu@intel.com>
Cc: Zhang Lubo <lubo.zhang@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiaxin Wu <jiaxin.wu@intel.com>
Reviewed-by: Zhang Lubo <lubo.zhang@intel.com>
Reviewed-by: Ye Ting <ting.ye@intel.com>
Reviewed-by: Fu Siyuan <siyuan.fu@intel.com>
The AllocateCopyPool in function ExtractFileNameFromDevicePath
may return NULL, so need to do error handling. This patch is to
add error handling codes for function ExtractFileNameFromDevicePath
and its caller functions.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Hao Wu <hao.a.wu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
The UefiPxeBcDxe module encounters a build error for IA32 arch using the
latest version of VS2015:
UefiPxe4BcDxe.lib(PxeBcDhcp.obj) : error LNK2001: unresolved external
symbol __allmul
The cause is line 1659 in file
MdeModulePkg/Universal/Network/UefiPxeBcDxe/PxeBcDhcp.c. The third
parameter for gBS->SetTimer() function is of type UINT64, so the
multiplication should use the MultU64x32() function.
Cc: Ye Ting <ting.ye@intel.com>
Cc: Fu Siyuan <siyuan.fu@intel.com>
Cc: Wu Jiaxin <jiaxin.wu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Fu Siyuan <siyuan.fu@intel.com>
Reviewed-By: Wu Jiaxin <jiaxin.wu@intel.com>
This is a enhancement to support the case when platform firmware
doesn't support Boot Manager Menu. For now, if BootManagerMenu FFS
can not be retrieved from FV, BDS core code will still register a
boot option for it. Then, this non-functional boot option will
still be booted by user's request (like HotKey or Exit from shell)
to cause additional boot time and error status code reported.
Therefore, it would be good to skip BootManagerMenu boot option
registration and then return error status and Invalid BootOption
data for this case so that the BootManagerBoot() or other consumers
can directly return without doing anything.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Sunny Wang <sunnywang@hpe.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Code logic ensures that both pointers 'DriverInfoData' and 'AllocInfoData'
will not be NULL when they are used.
Add ASSERTs as warning for cases that will not happen.
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
This change is to avoid UEFI SCT failure as UEFI SCT has no knowledge
about how to accessing a EMMC RPMB partition.
The user needs to access RPMB partition should get access through
EFI_SD_MMC_PASS_THRU protocol with authentication key & mac.
Cc: Hao Wu <hao.a.wu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
We have to upgrade the TPL level used by SdMmc stack because the
following flow:
DiskIo2ReadWriteDisk() in logical partition -> PartitionReadBlocksEx()
in logical partition at TPL callback level -> ProbeMediaStatusEx()
with sync request -> DiskIo2ReadWriteDisk() in physical partition ->
waiting for async task completion.
if the low layer driver doesn't run at TPL_NOTIFY level, it will have
no time to trigger async task and cause system hang.
Cc: Hao Wu <hao.a.wu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
Provides services to record memory profile of multilevel caller.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
1. Produce SMM memory profile protocol.
2. Consume PcdMemoryProfilePropertyMask to support disable recording
at the start.
3. Consume PcdMemoryProfileDriverPath to control which drivers need
memory profile data.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
1. Implement include GetRecordingState/SetRecordingState/Record for
memory profile protocol.
2. Consume PcdMemoryProfilePropertyMask to support disable recording
at the start.
3. Consume PcdMemoryProfileDriverPath to control which drivers need
memory profile data.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Current memory profile feature:
1. Shows which line of code calls gBS->AllocateXXX(). But most entries
are from MemoryAllocationLib.
2. Records at the start.
3. Records all modules.
Enhanced memory profile feature:
1. User can know which line of code calls AllocateXXX() API instead of
gBS->Allocate().
2. User can know which line of code calls a specific API that will call
AllocateXXX().
3. User can know total memory allocated by a specific line of code.
4. User can configure to record single module.
5. User can configure when to enable recording.
6. User can know RVA<->Symbol (Function, Source, Line).
For the enhanced memory profile feature,
1. Extend MEMORY_PROFILE_DRIVER_INFO to include PdbString.
2. Extend MEMORY_PROFILE_ALLOC_INFO to include ActionString.
3. Extend MEMORY_PROFILE_ACTION to indicate action in memory allocation
lib and user defined action.
4. Extend memory profile protocol to include GetRecordingState/
SetRecordingState/Record.
5. Define SMM memory profile protocol.
6. Extend PcdMemoryProfilePropertyMask to support disable recording at
the start.
7. Introduce new PCD PcdMemoryProfileDriverPath to control which drivers
need memory profile data.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
PI specification Vol 4 - SMM does not have any limitation of BASE_4GB for SMM.
So we should replace BASE_4GB check with MAX_ADDRESS check to make sure
the SMM memory is accessible by SMM Core.
Cc: Jeff Fan <jeff.fan@intel.com>
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Michael D Kinney <michael.d.kinney@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
GCC build failure: 'RealCommSize' may be used uninitialized
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Giri P Mudusuru <giri.p.mudusuru@intel.com>
According to spec if the length of a descriptor is smaller than
what the specification defines, then the host shall ignore it.
However if the size is greater than expected the host will ignore
the extra bytes and start looking for the next descriptor
at the end of actual length returned. Original check did not
handle the latter case correctly and only allowed descriptors
with lengths exactly as defined in specification.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Evgeny Yakovlev <insoreiges@gmail.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Let data of DXE memory status code can be used by other modules.
1. Save the address of DXE memory status code table to DxeConfigurationTable.
2. Save the address of SMM memory status code table to SmmConfigurationTable.
3. Move RUNTIME_MEMORY_STATUSCODE_HEADER to its public header file.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Cinnamon Shia <cinnamon.shia@hpe.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
The 'Sting' is returned by the function GetUnicodeStringTextAndSize.
If it is NULL, function GetUnicodeStringTextAndSize will return
EFI_OUT_OF_RESOURCES, and error handling codes will cover it.
So the pointer 'Sting' can not be NULL when using it.
So we can add the ASSERT codes.
Cc: Eric Dong <eric.dong@intel.com>
Cc: Hao Wu <hao.a.wu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
Use real nasm instruction to replace DB bytes.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Liming Gao <liming.gao@intel.com>
The BaseTools/Scripts/ConvertMasmToNasm.py script was used to convert
X64/S3Asm.asm to X64/S3Asm.nasm
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
Use real nasm instruction to replace DB bytes.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Liming Gao <liming.gao@intel.com>
The BaseTools/Scripts/ConvertMasmToNasm.py script was used to convert
IA32/S3Asm.asm to IA32/S3Asm.nasm
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
The BaseTools/Scripts/ConvertMasmToNasm.py script was used to convert
X64/EbcLowLevel.asm to X64/EbcLowLevel.nasm
And, manually update nasm code to use mov rcx, dword value and generate
the same assembly code with rcx register to asm code.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
The BaseTools/Scripts/ConvertMasmToNasm.py script was used to convert
Ia32/EbcLowLevel.asm to Ia32/EbcLowLevel.nasm
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
The BaseTools/Scripts/ConvertMasmToNasm.py script was used to convert
X64/AsmFuncs.asm to X64/AsmFuncs.nasm
Note: Also applied many manual cleanups where conversion script failed
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
The BaseTools/Scripts/ConvertMasmToNasm.py script was used to convert
Ia32/AsmFuncs.asm to Ia32/AsmFuncs.nasm
Note: Also applied many manual cleanups where conversion script failed
And, update Vect2Desc() to be same to original logic
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
The BaseTools/Scripts/ConvertMasmToNasm.py script was used to convert
X64/PageFaultHandler.asm to X64/PageFaultHandler.nasm
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
The BaseTools/Scripts/ConvertMasmToNasm.py script was used to convert
Ia32/IdtVectorAsm.asm to Ia32/IdtVectorAsm.nasm
Note: Manually updated code storing @VectorTemplateBase address
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Without this change, after converting this code to NASM, this error
will be reported:
error: comma or end of line expected
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
NASM doesn't support EXTERNDEF, so convert this to PUBLIC.
This will make it easier to convert this code to NASM using an
automated script.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Without this change, after converting this code to NASM, this error
will be reported:
error: invalid combination of opcode and operands
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
When a driver also uses a same name, there will be a link error:
one or more multiply defined symbols found.
Use a specific name for mSmst to avoid the link error.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
After booting a large-size ISO RAM disk (HTTP boot option pointing to
a ISO file) and reboot system, system will possibly run into the
following ASSERT because the BDS core code doesn't consider the
case that Memory page management (Page.c) would possibly NOT update
current memory usage statistics(CurrentMemoryTypeInformation) if
system allocates a memory buffer with a large number of pages.
ASSERT [DxeCore] u:\MdeModulePkg\Core\Dxe\Gcd\Gcd.c(2273):
Length >= MinimalMemorySizeNeeded
The BDS code block for skipping counting reserved memory occupied
by RAM Disk didn't consider the Memory page management's behavior
mentioned above, which caused that the
CurrentMemoryTypeInformation[Index1].NumberOfPages will be updated
to a "very big value" because RamDiskSizeInPages is bigger than
CurrentMemoryTypeInformation[Index1].NumberOfPages. For example,
NumberOfPages is 0x9000 (current use) and RamDiskSizeInPages is
0xC0000 (ISO image size). The result will become a very big value
0xFFF49000.
Therefore, we need to add a check to prevent BDS core code updating
wrong data (very big value) to MemoryTypeInformation variable. This
code change is a improvement for fixing this issue for most cases.
There is still a corner case even when the memory bins don't include
the RAM disk memory, the memory used by all other modules exceeds
RamDiskSizeInPages. Ray will send the other patch to fix this corner
case.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Sunny Wang <sunnywang@hpe.com>
Reviewed-by: Samer El-Haj-Mahmoud <elhaj@hpe.com>
Reviewed-by: Ruiyu Ni <Ruiyu.ni@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
This delay is necessary for eMMC reset to working properly.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Joe Zhou <shjzhou@marvell.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
PeiCore EntryPoint library _ModuleEntryPoint() will call PeiCore(), then call
CpuDeadLoop (). When NORETURN is added for PeiCore(), MSVC compiler will report
warning C4702: unreachable code for CpuDeadLoop (). And, the warning is treated
as error and cause build break. DxeMain() has the similar issue.
edk2 uses EntryPoint library to wrap every module entry point function except
for SEC. The module entry point is still called by _ModuleEntryPoint(). So,
there will be negative impact to add NORETURN for the module entry point.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Liming Gao <liming.gao@intel.com>
This patch is used to fix the wrong IpSb->State update issue.
Issue reproduce steps:
1 .First PXE boot, then boot to shell;
2. ifconfig -s eth0 dhcp (Success);
3. Reboot and do PXE, then boot to shell;
4. ifconfig -s eth0 dhcp (Platform failed to get IP address no matter
how many times retried.)
Root cause:
On step3 reboot, policy is DHCP (Changed by step2). So, Ip4Dxe driver
will try to get one IP address from DHCP server automatically. Before
it get the IP address successfully, the IpSb->State will be always in
IP4_SERVICE_STARTED status until the Instance->Dhcp4Event is triggered,
then it can be changed to IP4_SERVICE_CONFIGED. But the DHCP process
will be interrupted by PXE boot, which will change the policy to static,
and the Instance->Dhcp4Event will be also closed directly. However,
current implementation doesn't update the IpSb->State to
IP4_SERVICE_UNSTARTED status in such case. So, failure happened.
Cc: Ye Ting <ting.ye@intel.com>
Cc: Fu Siyuan <siyuan.fu@intel.com>
Cc: Ryan Harkin <ryan.harkin@linaro.org>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiaxin Wu <jiaxin.wu@intel.com>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Fu Siyuan <siyuan.fu@intel.com>
Reviewed-by: Ye Ting <ting.ye@intel.com>
Tested-by: Ryan Harkin <ryan.harkin@linaro.org>
Per UEFI spec the successful returning of boot option triggers boot
to UI. But when the BootNext just points to UI, it causes confusing.
So the patch avoids booting to UI again when the BootNext points to
UI.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Amy Chan <amy.chan@intel.com>
Add a new head file Dhcp.h in Mde/Include/IndustryStandard, normalize the
universal option numbers and other network number tags.
Cc: Sriram Subramanian <sriram-s@hpe.com>
Cc: Ye Ting <ting.ye@intel.com>
Cc: Fu Siyuan <siyuan.fu@intel.com>
Cc: Wu Jiaxin <jiaxin.wu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Zhang Lubo <lubo.zhang@intel.com>
Reviewed-by: Fu Siyuan <siyuan.fu@intel.com>
It is enough to set PxCMD.FRE bit, which cause HBA to post received FISes
into the FIS receive area. According to AHCI Specification, only polling on
PxCMD.FRE to be cleared is necessary, when it is needeed to stop FIS engine
(eg. in order to change PxCMD.FB address).
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jan Dabros <jsd@semihalf.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Per UEFI spec the successful returning of boot option triggers boot
to UI. But when the BootNext just points to UI, it causes confusing.
So the patch avoids booting to UI again when the BootNext points to
UI.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Amy Chan <amy.chan@intel.com>
This patch adds the NORETURN attribute to functions that transfer to
other phases, along with an UNREACHABLE() call at the end to avoid
false warnings.
DxeIpl has been excluded as its main function returns a status.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Marvin Haeuser <Marvin.Haeuser@outlook.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
It is the follow up of 3ab41b7a32
to replace UnicodeStrToAsciiStr/AsciiStrToUnicodeStr with
UnicodeStrToAsciiStrS/AsciiStrToUnicodeStrS.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jaben Carsey <jaben.carsey@intel.com>
In current UI code, we use oneof opcode without storage for language
menu. If we change the language form A->B, then go to another form and
then go back to the front page, the language menu always shows A. Now
we fix this issue by retrieving the value of oneof opcode(language menu)
when display it.
Cc: Liming Gao <liming.gao@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
The connect all action has been done in UiApp,
no need to do it when update boot manager form.
Cc: Liming Gao <liming.gao@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
If the connect all action has not been performed before.
We do it in UiApp now.
Cc: Liming Gao <liming.gao@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
When Hii variable is not present and if we try to update a variable offset
with some value, we are creating a new variable by Zeroing all the variable
offsets except the one which we are trying to update.
This will override all the other variable default values which are
programmed as a part of initial PCD definition.
DXE PCD driver could be enhanced to combine the DynamicHii
PCDs(related to same variable) default values and only update the offset
PcdSetXXX want to set, then set the combined values to variable.
Cc: Liming Gao <liming.gao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
When adding font package, there exists the case that only have the
EFI_HII_GIBT_GLYPH_DEFAULT or EFI_HII_GIBT_GLYPHS_DEFAULT glyph block
and use the default cell info in font package fixed header. In this
case, we can't get the correct baseline now. This patch is to fix this
issue by recalculating the baseline when the glyph block type is
EFI_HII_GIBT_GLYPH_DEFAULT or EFI_HII_GIBT_GLYPHS_DEFAULT.
Cc: Liming Gao <liming.gao@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
In current code, when adding string package, it will return
'gStringPackHandle'. But the code use the 'gHiiHandle' to get
string. It is incorrect. This patch is to fix this issue.
Cc: Eric Dong <eric.dong@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
There is static scan tool reports BootScriptSave.c:628:'mSmst' is
explicitly dereferenced.
The patch is to check (mSmst != NULL) before freeing SMRAM at
BootScriptSave.c:628.
Cc: Shumin Qiu <shumin.qiu@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Shumin Qiu <shumin.qiu@intel.com>
Add gPerformanceProtocolGuid in BdsDxe.inf explicitly.
Currently, BdsDxe could build pass as it inherits
gPerformanceProtocolGuid from UefiBootManagerLib.inf.
Also update the usage of gPerformanceProtocolGuid in UefiBootManagerLib.inf.
Cc: Liming Gao <liming.gao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Adding an option in HII menu so user can choose memory type to use when
creating a RAM Disk in system.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Tapan Shah <tapandshah@hpe.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Samer El-Haj-Mahmoud <elhaj@hpe.com>
The 'Size' numeric value used when creating a raw RAM disk does not
require a varstore to save its previous value in the create raw RAM disk
HII page.
The expecting behavior is that after a user created a raw RAM disk, the
next time when the create raw RAM disk page is entered, the 'Size' numeric
will be the default value (EFI_PAGE_SIZE).
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Tapan Shah <tapandshah@hpe.com>
This patch is used to update IP4->Configure() to allow the upper layer
modules to obtain a default address by setting UseDefaultAddress to TRUE
when default address is not available yet.
Cc: Ye Ting <ting.ye@intel.com>
Cc: El-Haj-Mahmoud Samer <samer.el-haj-mahmoud@hpe.com>
Cc: Subramanian Sriram <sriram-s@hpe.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiaxin Wu <jiaxin.wu@intel.com>
Reviewed-by: Ye Ting <ting.ye@intel.com>
Reviewed-by: Ye Ting <ting.ye@intel.com>
Reviewed-by: Sriram Subramanian <sriram-s@hpe.com>
Tested-by: Sriram Subramanian <sriram-s@hpe.com>
With a destructor implemented, the shortcut from 058196bbb3
should be unnecessary.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Suggested-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
PiDxeS3BootScriptLib has a constructor S3BootScriptLibInitialize() that
registers ready-to-lock callback S3BootScriptSmmEventCallBack() and several
more. The library is linked to SMM modules. If the module entry-point
function returns error (because of lack of resources, unsupported,
whatever), the module will be unloaded and the notify callback pointers
will point to undefined memory. On ready-to-lock exception occurs when
calling S3BootScriptSmmEventCallBack(), and probably all the other
callbacks registered by the constructor would also cause exception.
This patch is to implement library Destructor to free the resources
allocated by S3BootScriptLibInitialize() and unregister callbacks.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
SmmLockBoxSmmLib is linked to SMM modules. If the module entry-point
function returns error, the module will be unloaded and the global
variables will point to undefined memory.
This patch is to add DESTRUCTOR SmmLockBoxSmmDestructor to uninstall
SmmLockBoxCommunication configuration table if it has been installed
in Constructor.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
If there is no multiplier, the DEV bit of the ATA device register would
always be set. It causes that some ATA hard drives don't response the
ATA identity command sent to them.
Below is the description about DEV bit in ATA spec:
A device is selected when the DEV bit of the Device register is equal to
the device number assigned to the device by means of a Device 0/Device 1
jumper or switch, or use of the CSEL signal.
Below is the description about DEV bit in SATA spec:
When the DEV bit in the Device register is set to one, selecting the
non-existent Device 1, the host adapter shall respond to register reads
and writes as specified for a Device 0 with no Device 1 present, as
defined in the ATA/ATAPI-5 standard.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Cinnamon Shia <cinnamon.shia@hpe.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
When add Font Package, the cell in EFI_HII_FONT_PACKAGE_HDR
contains the measurement of the widest and tallest characters
in the font. The measurement may be not absolutely correct,
so when use this cell information to calculate the baseline may
cause incorrect result. Besides this calculation is not necessary.
So remove it now.
Cc: Liming Gao <liming.gao@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
When render string to screen, for proportional fonts,
the background color may not set to the whole BltBuffer.
And this will cause incorrect display.
Now initialize the background color to fix this issue.
Cc: Liming Gao <liming.gao@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Prevent the BmRepairAllControllers routine in an infinite loop
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Gary Li <garyli@hpe.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
The Maximum Queue Entries Supported (MQES) field in the CAP (Controller
Capabilities) register for a NVMe controller restrict the maximum
individual queue size that the controller supports.
The origin code does not check this value and always uses a hardcode value
when creating I/O submission/completion queues for asynchronous
transmission. The hardcode value might be larger than the MQES field, this
will lead to an 'Invalid Queue Size' error when creating I/O
submission/completion queues.
The patch will add checks to make sure proper queue size is passed when
creating I/O submission/completion queues.
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@Intel.com>
v2:
*Refine the coding style according edk2 community's feedback.
Current SNP UNDI Initialize command does not follow the UEFI Spec
to update the SNP MediaPresent field. The result for the Initialize
command execution check should be:
StatFlags: (1) Monitor the upper two bits (14 & 15) in the field to know
whether the command has been executed by the UNDI (Not started, Queued,
Error, Complete). (2) Check the other field to see if there is an active
connection to this network device (used to update MediaPresent).
StatCode: After command execution completes, either successfully or not,
this field contains the result of the command execution (success or failure).
This patch is used to fix it.
NOTE: If any UNDI driver does not follow the UEFI Spec for the media status
update, it may meet failure with this more conditions check (StatFlags).
Cc: Ye Ting <ting.ye@intel.com>
Cc: Fu Siyuan <siyuan.fu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiaxin Wu <jiaxin.wu@intel.com>
Reviewed-by: Ye Ting <ting.ye@intel.com>
In Ip4CleanService()it first cleaned some resources, then stop the timer .
While before the timer stopped it may try to access some already freed
data, which may generate an exception.
This patch updates the driver to stop the timer event before starting to
clean up the service data.
Cc: Wu Jiaxin <jiaxin.wu@intel.com>
Cc: Ye Ting <ting.ye@intel.com>
Cc: Subramanian Sriram <sriram-s@hpe.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Fu Siyuan <siyuan.fu@intel.com>
Reviewed-by: Samer El-Haj-Mahmoud <elhaj@hpe.com>
Reviewed-by: Sriram Subramanian <sriram-s@hpe.com>
Reviewed-by: Ye Ting <ting.ye@intel.com>
Reviewed-by: Wu Jiaxin <jiaxin.wu@intel.com>
Potentially uninitialized local variables 'TableKey' and 'TableHeader'
might be used in functions RamDiskPublishNfit() and RamDiskUnpublishNfit()
in file RamDiskProtocol.c.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Qiu Shumin <shumin.qiu@intel.com>
According to PI specification, EndOfDxe Event should be signaled before
DxeSmmReadyToLock protocol installation. This update is ASSERT if EndOfDxe
Event is not signaled when DxeSmmReadyToLock protocol installed. And do
REPORT_STATUS_CODE() also.
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
PI1.4a spec added "For S3 resume boot modes DXE IPL must be
prepared to execute without permanent memory installed and
invoke the S3 resume modules."
To follow PI1.4a spec, this patch is to update DxeIpl and
PeiCore to enable S3 resume from temporary memory.
The normal boot path still enforces the permanent memory
requirement.
Cc: Liming Gao <liming.gao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Eugene Cohen <eugene@hp.com>
Signed-off-by: Star Zeng <star.zeng@intel.com>
Tested-by: Katie Dellaquila <katie.dellaquila@hp.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
The BootLogoUpdateProgress() function uses the
EFI_GRAPHICS_OUTPUT_BLT_PIXEL type in its parameter list, but the protocol
header that defines this type is not included. This breaks dependent C
source files that don't otherwise include the GraphicsOutput protocol
header. Supply the necessary include directive.
(Similarly, BootLogoEnableLogo() uses
EDKII_PLATFORM_LOGO_DISPLAY_ATTRIBUTE in its parameter list. For that
however, the PlatformLogo protocol header is included already.)
Cc: Feng Tian <feng.tian@intel.com>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
Move NvmExpressHci.h definitions to a public industry standard
header in MdePkg. The NvmExpressHci.h contains definitions based
on the NVMe v1.1 specification. These definitions should be in
a public header so that clients of the NVMe passthru protocol
can use them to execute NVMe commands.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Darbin Reyes <darbin.emm.reyes@hpe.com>
Reviewed-by: Samer El-Haj-Mahmoud <samer.el-haj-mahmoud@hpe.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
This patch is used to remove the status check for SockProcessRcvToken.
It's not return EFI_STATUS.
Cc: Fu Siyuan <siyuan.fu@intel.com>
Cc: Ye Ting <ting.ye@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiaxin Wu <jiaxin.wu@intel.com>
Reviewed-by: Ye Ting <ting.ye@intel.com>
Reviewed-by: Fu Siyuan <siyuan.fu@intel.com>
The following codes are useless and cause memory leak issues.
So now remove them.
Cc: Cecil Sheng <cecil.sheng@hpe.com>
Cc: Qiu Shumin <shumin.qiu@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
The driver entry point calls gDS->SetMemorySpaceAttributes().
This interface may return EFI_NOT_AVAILABLE_YET when CPU Arch
protocol is not available.
So we need to list CpuArch protocol in its INF dependency section.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
PciBus driver originally always degrade (64->32) the MMIO resource
for PCI BAR when the PCI device contains option ROM.
But the degrade causes the PCI device can only use resource below 4GB
which makes the resource allocation fails when the PCI device wants
very big MMIO.
The patch follows the PI spec (ECR 1529) to honor the granularity
setting for PCI BAR from IncompatiblePciDeviceSupport so that even
for PCI device which contains option ROM, the degrade doesn't happen
if IncompatiblePciDeviceSupport returns 64 as granularity.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Remove "Efi" from gEfiIncompatiblePciDeviceSupport to shorten
the global variable name.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
There is absolutely no reason to artificially limit the SKU range to 1-255.
PI1.4a spec fixed the artificial limitation.
This patch is to follow PI1.4a spec to remove the sentence
"The valid SkuId range is 1 to 255." from SetSku function comments.
Cc: Liming Gao <liming.gao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
This patch implements the EFI_ERASE_BLOCK_PROTOCOL in ScsiDiskDxe driver.
For now, the codes support the erase block feature only on Universal Flash
Storage (UFS) devices.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Together with EFI_BLOCK_IO_PROTOCOL, EFI_BLOCK_IO2_PROTOCOL is also
produced on NVMe devices.
The following Block I/O 2 functions are implemented:
Reset
ReadBlocksEx
WriteBlocksEx
FlushBlocksEx
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
In current code, BootManagerUiLib is not BDS scope.
So we remove bds keyword in the function name.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
In current code, BootMaintenanceManagerUiLib is not BDS scope.
So we remove bds keyword in the function name.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
In current code, UiApp is not the BDS scope. So we remove the bds
keyword in the function name.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
In current code, we use different output modes for boot phase
and setup phase. When split BootMaintenanceMangerUiLib from
UiApp code, we not add logic to save the boot phase mode info
which will be used later. This change add this logic.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
In current code, we use different output modes for boot phase
and setup phase. When split BootManagerUiLib from UiApp code,
we not add logic to save the boot phase mode info which will
be used later. This change add this logic.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
FirmwareVolmeInfoPpiNotifyCallback is re-enterable during FV process. Since PrivateData->FVCount increases when processing each sub FVs, need to cache Parent FV count in stack before processing any sub FV.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Chao Zhang <chao.b.zhang@intel.com>
Reviewed-by: Gao Liming <liming.gao@intel.com>
When the parameter is unsupported or invalid,
should exit the function.
Cc: Qiu Shumin <shumin.qiu@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Qiu Shumin <shumin.qiu@intel.com>
When PcdPciDisableBusEnumeration is enabled, the PciBus driver
might get into a dead loop if the secondary bus register on PCI
bridge is not programmed or programmed improperly. Adding this
check to avoid any potential dead loop caused by this.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Maurice Ma <maurice.ma@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Lee Leahy <Leroy.p.leahy@intel.com>
The original BdsDxe driver has "Enter Setup" status code
while current code not. This patch restores it.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
When copy new string content to BufferValue, need to clean the
BufferValue firstly, or the BufferValue may contain some
content that doesn't belong to the new string.
Cc: Liming Gao <liming.gao@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
When submit form fail, the progress point to the first fail part
in ConfigResp, so should free the ConfigResp after Progrss has
been processed.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Static storage duration objects that are internal to a library instance
should:
- either have internal linkage (i.e., be declared STATIC),
- or, if they are referenced in multiple files of the library instance,
prefixed with a word that is specific to the library instance, and
minimizes namespace collisions.
In this case, the "gHiiDriverList" variable (with static storage duration
and external linkage) is defined in both BootMaintenanceManagerUiLib and
UiApp. When these are linked together, GCC catches the multiple external
definitions and aborts the build. (GCC notices this due to commit
214a3b79417f.) Fix the error by applying the first rule above.
Fixes: a85be3ae48
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
This patches rename CoreGetMemoryMapPropertiesTable to
CoreGetMemoryMapWithSeparatedImageSection.
The reason is that CoreGetMemoryMapPropertiesTable is called
by MemoryAttributesTable.c to get separated PE image section
information.
It is confusing to use *PropertiesTable, because it is NOT
related to PropertiesTable.c
We rename it to avoid confusing.
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Current GetVariable implementation will return the first variable for
empty str VariableName, it is because GetVariable and GetNextVariablename
are sharing same function FindVariable.
But UEFI sepc defines SetVariable that If VariableName is an empty string,
then EFI_INVALID_PARAMETER is returned, that means an empty string variable
could never be set successfully, so GetVariable should return error for
empty string VariableName.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Change file arrangement to let user easy customize the front page UI.
After this change:
1. UiCustomizeFrontPage function in FrontPageCustomizedUi.c use to
let user customize front page menus. UiFrontPageCallbackHandler
function use to handle the callback for the added menus.
2. FrontPageCustomizedUiSupport.c file used to add support functions
used by FrontPageCustomizedUi.c file.
3. After this change, only above two files need to be updated if front page
menus needed to be changed.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Change file arrangement to let user easy customize the BMM UI.
After this change:
1. UiCustomizeBMMPage function in BootMaintenanceManagerCustomizedUi.c
use to let user customize BMM first page menus. UiBMMCallbackHandler
function use to handle the callback for the added menus.
2. BootMaintenanceManagerCustomizedUiSupport.c file used to add support
functions used by BootMaintenanceManagerCustomizedUi.c file.
3. After this change, only above two files need to be updated if BMM
first page menus needed to be changed.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
HttpGenRequestMessage assumes that HTTP message would always
contain a request-line, headers and an optional message body.
However, subsequent to a HTTP PUT/POST request, HTTP requests
would contain just the message body. This patch supports
creation of such request messages with additional checks.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hegde, Nagaraj P <nagaraj-p.hegde@hpe.com>
Reviewed-By: Wu Jiaxin <jiaxin.wu@intel.com>
Reviewed-by: Fu Siyuan <siyuan.fu@intel.com>
The Mantis ticket 1353 <https://mantis.uefi.org/mantis/view.php?id=1353>
and Mantis ticket 1472 <https://mantis.uefi.org/mantis/view.php?id=1472>
updated the description of the port multiplier port number parameter in
SATA Device Path Node and ATA Pass-Through Protocol.
Now, this parameter should be set to 0xFFFF instead of 0 to indicate that
an ATA device is directly attached on the controller port.
Please note that this is an incompatible change. The consumer of SATA
device path or ATA_PASS_THRU needs to re-examine its usage to follow UEFI
2.5 mantis 1353 and 1472.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Change PciHostBridgeDxe driver to not install the
PciHostBridgeResourceAllocation protocol and let
PciRootBridgeIo.Configuration() return the correct PCI resource
assignment information when the ResourceAssigned is TRUE.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Some platform doesn't require PciBus driver to assign resource
to PCI devices which causes PciRootBridgeIo.Configuration() cannot
return correct resource information to caller.
When resource assignment by PciBus is not mandatory, only light
version of PCI bus enumeration is performed, which only collects
the device resource consumption and publishes the PciIo instance.
The corresponding logic is in PciEnumeratorLight() in PciBus driver.
But PciEnumeratorLight() still depends on
PciRootBridgeIo.Configuration() returns the starting bus number in
order to search down to find all PCI devices under the root bridge.
When ResourceAssigned in PCI_ROOT_BRIDGE returned by
PciHostBridgeGetRootBridges() is TRUE, PciHostBridge driver treats
the Bus/Io/Mem/MemAbove4G/PMem/PMemAbove4G as the resource that are
*actually assigned* to the root bridge, instead of the resource that
*can be assigned* to the root bridge.
So that PciRootBridgeIo.Configuration() can return the correct
information.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
When the aperture base equals to aperture limit, the old code treats
the aperture as non-existent. It's not correct because it indicates
a range starting with base and the length is 1.
The new code corrects the comparing bug.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
The patch aligns to the IntelFrameworkModulePkg/Bus/Isa/IsaSerialDxe
driver not flush the UART in Reset() and SetAttributes() function.
It was found the flush causes hang on certain PCI serial devices.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Eric Jin <eric.jin@intel.com>
The RamDiskDxe driver originally uses a variable-length HII varstore to
retrieve the HII checkbox status of each registered RAM disk.
However, HII does not support the variable-length varstore feature.
Therefore, only the checkbox status for the first 8 RAM disks are tracked
for the following definition of HII varstore structure considering the
alignment:
typedef struct {
UINT64 Size;
UINT8 RamDiskList[0];
} RAM_DISK_CONFIGURATION;
This commit uses the private data of each registered RAM disks to track
the HII checkbox status instead to resolve the issue.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
The RamDiskDxe now will report RAM disks with reserved memory type to NFIT
in the ACPI table.
This commit will also make sure that an NVDIMM root device exists in the
\SB scope before reporting any RAM disk to NFIT.
To properly report the NVDIMM root device, one will need to append the
following content in the [Rule.Common.DXE_DRIVER] field in platform FDF
files:
RAW ACPI Optional |.acpi
RAW ASL Optional |.aml
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Samer El-Haj-Mahmoud <elhaj@hpe.com>
when there's no volume label 'Info' can be NULL
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Michael Zimmermann <sigmaepsilon92@gmail.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Before switch to a bus mode, we need check if the SD device supports
this bus mode.
Cc: Wu, Hao A <hao.a.wu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
The original code is using ADMA mode to do clock tuning procedure. It
may have problem on some SD/MMC host controllers as there is no way to
know when to send next tuning cmd.
Update it to PIO mode to strictly follow SD Host Controller Simplified
Specification 3.0 Figure 2-29. By this way, if the Buffer Read Ready
interrupt is set, we could know it's ok to send the next clock tuning
cmd.
Cc: Wu, Hao A <hao.a.wu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
The original code has a bug to calculate which clock freq should be
used when the target clock freq is larger than the BaseClock Freq
provided by the system.
Cc: Wu, Hao A <hao.a.wu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Check if the card is identified/initialized correctly. if not, break
the following cmd execution through PassThru()/ResetDevice().
Cc: Wu, Hao A <hao.a.wu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Make sure "BootFileName" is not overloaded before use it in PXE driver.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: chenzhihui <chenzhihui4@huawei.com>
Signed-off-by: Heyi Guo <heyi.guo@linaro.org>
Reviewed-by: Fu Siyuan <siyuan.fu@intel.com>
In current code will always call submit callback function,
but we should call submit callback function when has no failure
in the submit action. This patch to fix this issues.
Cc: Liming Gao <liming.gao@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
When RouteConfig function fail in SubmitForForm or SubmitForFormSet
function, we should restore the question value base on the failure
information, should not restore all the question.
This patch to fix this issue.
Cc: Liming Gao <liming.gao@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
The "IoAlign" field in EFI_BLOCK_IO_MEDIA of an NVMe device is not
initialized properly, leading to a zero value for this field.
It should be initialized from the "IoAlign" field in the
EFI_NVM_EXPRESS_PASS_THRU_MODE structure maintained by the NVMe
controller.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Some UNDI drivers may not support the cable detect in UNDI INITIALIZE command,
but support the media present check in UNDI GET_STATUS command. Current SNP
driver will set the MediaPresentSupported field to FALSE in EFI_SIMPLE_NETWORK_MODE
for such case, which forbid the media detect from the callers.
This patch updates the SNP driver to support such kind of UNDIs for media detect.
MediaPresentSupported will be set to TRUE, and a GET_STATUS command will be issued
immediately after INITIALIZE command in SNP->Initialize() function, to refresh
the value of MediaPresent in SNP mode data.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Fu Siyuan <siyuan.fu@intel.com>
Reviewed-By: Ye Ting <ting.ye@intel.com>
Reviewed-By: Wu Jiaxin <jiaxin.wu@intel.com>
The USB flash drive with Vendor ID 0x1516 (CompUSA) and Product ID 0x6221
returns a broken "Supported VPD Pages" VPD page. In particular, the
PageLength field has the invalid value 0x0602 (decimal 1538).
This prevents the loop from terminating that scans for the Block Limits
VPD page code in ScsiDiskInquiryDevice():
for (Index = 0; Index < PageLength; Index++) {
because the Index variable has type UINT8, and it wraps from 255 to 0,
without ever reaching PageLength (1538), and because
EFI_SCSI_PAGE_CODE_BLOCK_LIMITS_VPD does not occur at offsets 0 through
255.
* The fix is not to change the type of Index to UINT16 or a wider type.
Namely, section
7.8.14 Supported VPD Pages VPD page
in the "SCSI Primary Commands - 4" (SPC-4) specification names the
following requirement:
The supported VPD page list shall contain a list of all VPD page codes
(see 7.8) implemented by the logical unit in ascending order beginning
with page code 00h.
Since page codes are 8-bit unsigned quantities, it follows that the
maximum size for the Supported VPD Pages VPD page is 0x100 bytes, in
which every possible page code (0x00 through 0xFF) will be found, before
the UINT8 offset wraps around.
(EFI_SCSI_SUPPORTED_VPD_PAGES_VPD_PAGE.SupportedVpdPageList is correctly
sized as well, in "MdePkg/Include/IndustryStandard/Scsi.h".)
* Instead, add sanity checks that enforce the above requirement. If the
device breaks the spec, simply fall back to the "Block Limits page
absent" case.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Ref: https://bugzilla.redhat.com/show_bug.cgi?id=1330955
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
EFI_PXE_BASE_CODE_PROTOCOL has interface to set the TTL and ToS value, but
not used by the UdpWrite() interface. The code always use a hard coded 16
for the TTL and 0 for ToS.
This patch update the UpdWrite() to use the TTL and ToS which have been set
by the SetParameters().
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Fu Siyuan <siyuan.fu@intel.com>
Reviewed-By: Wu Jiaxin <jiaxin.wu@intel.com>
Reviewed-By: Samer El-Haj-Mahmoud <elhaj@hpe.com>
Remove DeployedMode & AuditMode Global variable check for Customized Secure Boot feature defined in UEFI2.5 Mantis 1263.
The feature has been moved to
https://github.com/tianocore/edk2-staging/tree/Customized-Secure-Boot
Previous check-in hash is
SHA-1: 0f4f6d202a
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Chao Zhang <chao.b.zhang@intel.com>
Reviewed-by: El-Haj-Mahmoud Samer <samer.el-haj-mahmoud@hpe.com>
Reviewed-by: Fu Siyuan <siyuan.fu@intel.com>
Set the ImageContext.Handle and ImageContext.ImageRead() fields so that
PeCoffLoaderRelocateImageExtraAction() can invoke PeCoffLoaderGetImageInfo
or PeCoffLoaderGetPeHeader if desired to obtain additional metadata.
We will use this to create a PeCoffLoaderRelocateImageExtraAction()
implementation that applies boot time strict mapping permissions to
PE/COFF modules.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Star Zeng <star.zeng@intel.com>
If the current PCI configuration requires no resources to be allocated at
all (i.e., unpopulated bus), the PCI enumeration code creates a single
ACPI_ADDRESS_SPACE_DESCRIPTOR memory descriptor with all fields cleared.
This is rejected by the SubmitResources() implementation of the generic
PciHostBridgeDxe in the following way:
PciHostBridge: SubmitResources for PcieRoot(0x0)
Mem: Granularity/SpecificFlag = 0 / 00
Length/Alignment = 0x0 / 0x0
PciBus: HostBridge->SubmitResources() - Invalid Parameter
ASSERT_EFI_ERROR (Status = Invalid Parameter)
ASSERT [PciBusDxe] .../PciBusDxe/PciLib.c(561): !EFI_ERROR (Status)
So instead, create the empty configuration as a single entry of type
EFI_ACPI_END_TAG_DESCRIPTOR.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
This patch enhance performance data SMM communication by using fixed
SMM communication buffer.
Update PerformanceLib to use fixed SMM communication buffer to get
performance data by SMM_PERF_COMMUNICATE API.
This is designed to meet Microsoft WSMT table definition on FIXED_COMM_BUFFERS
requirement.
Cc: Liming Gao <liming.gao@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
This patch enhance performance data SMM communication by using fixed
SMM communication buffer.
Update FpdtDxe to use fixed SMM communication buffer to get
performance data by SMM_FPDT_FUNCTION_GET_BOOT_RECORD_DATA_BY_OFFSET API.
This is designed to meet Microsoft WSMT table definition on FIXED_COMM_BUFFERS
requirement.
Cc: Liming Gao <liming.gao@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
This patch enhance performance data SMM communication by using fixed
SMM communication buffer.
Update FpdtSmm to handle SMM_FPDT_FUNCTION_GET_BOOT_RECORD_DATA_BY_OFFSET
request.
This is designed to meet Microsoft WSMT table definition on FIXED_COMM_BUFFERS
requirement.
Cc: Liming Gao <liming.gao@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
This patch enhance performance data SMM communication by using fixed
SMM communication buffer.
A new command SMM_FPDT_FUNCTION_GET_BOOT_RECORD_DATA_BY_OFFSET is added,
because we need to support get partial PerformanceData to fixed SMM communication
buffer. If performance data is bigger than fixed SMM communication buffer,
the DXE agent need to call SMM_FPDT_FUNCTION_GET_BOOT_RECORD_DATA_BY_OFFSET
multiple times to get all data out.
This is designed to meet Microsoft WSMT table definition on FIXED_COMM_BUFFERS
requirement.
Cc: Liming Gao <liming.gao@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
This patch enhance SMM memory profile SMM communication by using fixed
SMM communication buffer.
Update MemoryProfileInfo APP to use fixed SMM communication buffer to get
profile data by SMRAM_PROFILE_COMMAND_GET_PROFILE_DATA_BY_OFFSET API.
This is designed to meet Microsoft WSMT table definition on FIXED_COMM_BUFFERS
requirement.
Cc: Star Zeng <star.zeng@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
This patch enhance SMM memory profile SMM communication by using fixed
SMM communication buffer.
Update PiSmmCore to handle SMRAM_PROFILE_COMMAND_GET_PROFILE_DATA_BY_OFFSET
request.
This is designed to meet Microsoft WSMT table definition on FIXED_COMM_BUFFERS
requirement.
Cc: Star Zeng <star.zeng@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Regression-tested-by: Laszlo Ersek <lersek@redhat.com>
This patch enhance SMM memory profile SMM communication by using fixed
SMM communication buffer.
A new command SMRAM_PROFILE_COMMAND_GET_PROFILE_DATA_BY_OFFSET is added,
because we need to support get partial ProfileData to fixed SMM communication
buffer. If profile data is bigger than fixed SMM communication buffer,
the DXE agent need to call SMRAM_PROFILE_COMMAND_GET_PROFILE_DATA_BY_OFFSET
multiple times to get all data out.
This is designed to meet Microsoft WSMT table definition on FIXED_COMM_BUFFERS
requirement.
Cc: Star Zeng <star.zeng@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Add a driver to publish EDKII_PI_SMM_COMMUNICATION_REGION_TABLE, so that
other DXE driver can consume this table directly. NOTE: This is sample driver.
A platform may uses its own way to define default SMM communication buffer
region and publish information in its own
EDKII_PI_SMM_COMMUNICATION_REGION_TABLE.
This is designed to meet Microsoft WSMT table definition on FIXED_COMM_BUFFERS
requirement.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Feng, Tian <feng.tian@intel.com>
This configuration table is used to describe platform pre-allocated memory
for SMM communication buffer. If DXE driver wants to communicate with SMM
agent, it can use this memory as SMM communication buffer instead of allocate
new memory region.
This is designed to meet Microsoft WSMT table definition on FIXED_COMM_BUFFERS
requirement.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
In the edk2 tree, there are currently four drivers that consume
PcdAcpiS3Enable:
IntelFrameworkModulePkg/Universal/Acpi/AcpiS3SaveDxe/AcpiS3SaveDxe.inf
MdeModulePkg/Universal/Acpi/BootScriptExecutorDxe/BootScriptExecutorDxe.inf
MdeModulePkg/Universal/Acpi/S3SaveStateDxe/S3SaveStateDxe.inf
MdeModulePkg/Universal/Acpi/SmmS3SaveState/SmmS3SaveState.inf
From these, AcpiS3SaveDxe is the only one that isn't also a client of the
S3BootScriptLib class; all the others (BootScriptExecutorDxe,
S3SaveStateDxe, SmmS3SaveState) are clients of the S3BootScriptLib class.
In turn, the edk2 tree contains only one non-Null instance of the
S3BootScriptLib class:
MdeModulePkg/Library/PiDxeS3BootScriptLib/DxeS3BootScriptLib.inf
Therefore we can safely state that BootScriptExecutorDxe, S3SaveStateDxe,
and SmmS3SaveState are all linked against PiDxeS3BootScriptLib.
Now, if PcdAcpiS3Enable is FALSE when either of BootScriptExecutorDxe,
SmmS3SaveState, or SmmS3SaveState is dispatched, then the following
happens:
- The constructor of PiDxeS3BootScriptLib, function
S3BootScriptLibInitialize(), registers a protocol installation callback
for gEfiDxeSmmReadyToLockProtocolGuid. Namely, the function
S3BootScriptEventCallBack().
- The driver immediately exits with EFI_UNSUPPORTED from its entry point
function, upon seeing PcdAcpiS3Enable == FALSE. (See commits
800c02fbe2, 125e093876, and d2d38610603f6.)
- This leaves a dangling callback pointer in the DXE core.
- When Platform BDS installs gEfiDxeSmmReadyToLockProtocolGuid (which is a
valid thing to do for locking down SMM, even in the absence of S3
support!), things blow up.
Fix this issue by returning immediately from S3BootScriptLibInitialize()
if PcdAcpiS3Enable is FALSE -- it is useless to initialize the library
instance if the containing driver module exits first thing in its entry
point.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jaben Carsey <Jaben.carsey@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Use 128 bytes as the start size region to be same to previous one.
64 bytes is small as the first range. On X64 arch, POOL_OVERHEAD
takes 40 bytes, the pool data less than 24 bytes can be fit into
it. But, the real allocation is few that can't reduce its free pool
link list. And, the second range (64~128) has more allocation
that also increases the free pool link list of the first range.
Then, the link list will become longer and longer. When LinkList
check enable in DEBUG tip, the long link list will bring the
additional overhead and bad performance. Here is the performance
data collected in our X64 platform with DEBUG enable.
64 byte: 22 seconds in BDS phase
128 byte: 19.6 seconds in BDS phase
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
The Hii runtime support feature will export the content of
HiiDatabase and the ConfigResp string to runtime buffer
after ReadyToBoot event is triggered. If some drivers
add/update/remove packages from Hiidatabase after ReadyToBoot:
Originally we will both export the content of HiiDatabase and
the ConfigResp string for all packages.
But now after investigation, we found only for form packages need
to export the content of HiiDatabase and the ConfigResp string,
for other packages just need to export the content of HiiDatabase.
Now to enhance this logic.
Cc: Liming Gao <liming.gao@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Samer El-Haj-Mahmoud <elhaj@hpe.com>
Rename and update the logic of HttpGenRequestString API provided
by DxeHttpLib. The RequestString size is returned as an argument.
The user is not expected to do a AsciiStrLen anymore, and is not
logical too, since request string can contain message body and
using AsciiStrLen on such a string can provide truncated lengths.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Nagaraj Hegde <nagaraj-p.hegde@hpe.com>
Reviewed-by: Fu Siyuan <siyuan.fu@intel.com>
Reviewed-by: Samer El-Haj-Mahmoud <elhaj@hpe.com>
It can improve profile performance, especially when
PcdMemoryProfileMemoryType configured without EfiBootServicesData.
CoreUpdateProfile() can return quickly, but not depend on the further
code to find the buffer not recorded and then return.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Phase Tag, SqTdbl/CqHdbl and SqBuffer/CqBuffer should be cleared in
NvmeControllerInit() to make HC functionality work when user invokes
NvmeBlockIoReset().
Cc: Simon (Xiang) Lian-SSI <simon.lian@ssi.samsung.com>
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Simon (Xiang) Lian-SSI <simon.lian@ssi.samsung.com>
In EnumerateNvmeDevNamespace(), when Private->ControllerData->Sn and/or
Private->ControllerData->Mn are NOT null-terminated strings,
UnicodeSPrintAsciiFormat(…) may generate unexpected (garbage) output
string.
Cc: Simon (Xiang) Lian-SSI <simon.lian@ssi.samsung.com>
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Simon (Xiang) Lian-SSI <simon.lian@ssi.samsung.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Memory pointed to by Private->ControllerData has not been freed up
correctly at error handling path.
Cc: Simon (Xiang) Lian-SSI <simon.lian@ssi.samsung.com>
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Simon (Xiang) Lian-SSI <simon.lian@ssi.samsung.com>
The close brace of EmmcDxeComponentNameGetControllerName should be
at the beginning of a line.
Cc: Qiu Shumin <shumin.qiu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Shumin Qiu <shumin.qiu@intel.com>
When the type of HiiValue is BUFFER Type, the BufferValue
of the related question can not be NULL, so can remove the
check.
Cc: Qiu Shumin <shumin.qiu@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Qiu Shumin <shumin.qiu@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
The patch uses CoreAcquireLockOrFail() instead of
CoreAcquireProtocolLock() in CoreLocateProtocol() to avoid
assertion when CoreLocateProtocol() is called with the
protocol database locked.
The issue was found when changing PcdDebugPrintErrorLevel to
enable page/pool allocation debug message.
Nt32 platform hangs immediately after DxeCore is loaded.
Investigation shows the following calling stacks:
DxeCore entry point (Install a certain protocol)
0 DxeCore::CoreInstallProtocolInterface // Protocol DB is locked
1 DxeCore::AllocatePool
2 PeiDxeDebugLibReportStatusCode::DebugPrint
3 DxeReportStatusCodeLib::ReportStatusCodeEx // <-------------------|
4 DxeReportStatusCodeLib::InternalGetReportStatusCode |
5 DxeCore::LocateProtocol(StatusCodeRuntimeProtocol) |
// Assertion when locking Protocol DB 2nd time |
6 DxeCore::CoreAcquireProtocolLock |
7 PeiDxeDebugLibReportStatusCode::DebugAssert |
8 DxeReportStatusCodeLib::ReportSatusCodeEx // loop begins ---------
In frame #6 the assertion is triggered due to the protocol database
is already locked. #8 calls #4 and the loop begins.
After changing #6 to CoreAcquireLockOrFail(), the assertion is
avoided and the loop is broken.
With the fix, NT32 can boot to Shell even setting
PcdDebugPrintErrorLevel to 0xFFFFFFFF, with all error levels turned
on.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
This library instance is PEIM type, not BASE type. It has the PPI
dependency for PEIM.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Add error handling logic in DriverBingingStop function,
it may return error status when invoking the
UninstallProtocolInterface.
Cc: Fu Siyuan <siyuan.fu@intel.com>
Cc: Ye Ting <ting.ye@intel.com>
Cc: Wu Jiaxin <jiaxin.wu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Zhang Lubo <lubo.zhang@intel.com>
Reviewed-by: Ye Ting <ting.ye@intel.com>
Reviewed-by: Fu Siyuan <siyuan.fu@intel.com>
Reviewed-by: Jiaxin Wu <jiaxin.wu@intel.com>
Current MemoryAttributesTable will be installed on ReadyToBoot event
at TPL_NOTIFY level, it maybe incorrect when PcdHiiOsRuntimeSupport
= TRUE as HiiDatabaseDxe will have runtime memory allocation for HII
OS runtime support on and after ReadyToBoot. The issue was exposed at
http://article.gmane.org/gmane.comp.bios.edk2.devel/10125.
To make sure the correctness of MemoryAttributesTable, this patch is
to enhance MemoryAttributesTable installation to install
MemoryAttributesTable on ReadyToBoot event at TPL_CALLBACK - 1 level
to make sure it is at the last of ReadyToBoot event, and also hook
runtime memory allocation after ReadyToBoot.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
The following patch for MemoryAttributesTable will need the memory type.
And CoreUpdateProfile() can also use the memory type for check.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Originally, the code block for "Report DXE Core image information to the PE/COFF
Extra Action Library" was after ProcessLibraryConstructorList(). To fix an issue,
ProcessLibraryConstructorList() was moved to be right after CoreInitializeGcdServices()
at c5d5379937, but the code block was left.
As there maybe PeCoffExtraActionLib implementation need Constructor executed first,
the patch is to move the code block for "Report DXE Core image information to the PE/COFF
Extra Action Library" to be after ProcessLibraryConstructorList.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
According to SD Host Controller 3.0 spec figure 3-10, we have to wait
1ms before checking DAT[3:0] in voltage switch proc
Cc: Hao Wu <hao.a.wu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
The original code doesn't reset the slot when there is device change.
It may bring issue on device identification procedure of some SD cards.
Cc: Hao Wu <hao.a.wu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@Intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
If there is no card presented before power on, there would
have no card change interrupt generated. This is a corner
case which can't be handled by old logic.
The patch is used to move card present detection in the front
of card change interrupt detection.
Cc: Hao Wu <hao.a.wu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
The bcdUSB value of usb3.1 is 0x0310, we update the condition judgment
to get correct max packet size for usb3.1 dev.
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
The GetKeyDescriptor() may return NULL when the KeyData is invalid.
For such case, we should go to error handling path rather than assert
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Allow EfiVarStore to get <AltResp> from Hii Driver, and enhance code logic
in MergeDefaultString function to get a full AltCfgResp.
The logic in function MergeDefaultString after enhancement:
(1) If there are no <AltResp> in AltCfgResp, merge the <AltResp> in
DefaultAltCfgResp to AltCfgResp.
(2) If there are <AltResp> in AltCfgResp, for the same <AltConfigHdr>, if
the <ConfigElement> already in AltCfgResp, don't need to merge from
DefaultAltCfgResp, else merge the <ConfigElement> in the DefaultAltCfgResp
to the related <AltResp> in AltCfgResp.
AltCfgResp: Generated by Driver.
DefaultAltCfgResp: Generated by HiiDatabase.
Cc: Liming Gao <liming.gao@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Add the sample case for orderedlist to get standard
default value from Callback function.
Cc: Liming Gao <liming.gao@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
For orderedlist question, the value is stored in a buffer,
not in HiiValue. So when need to get default value from callback
function for orderedlist, need to pass the buffer.
This patch is to enhance this logic.
Cc: Liming Gao <liming.gao@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Set the Force Unit Access (FUA) bit in NVMe Write - Command Dword 12 to
ensure write-through behavior.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Change to use a different FILE_GUID to avoid using the
same GUID as the module in IntelFrameworkModulePkg.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Shumin Qiu <shumin.qiu@intel.com>
Change to use a different FILE_GUID to avoid using the
same GUID as the module in IntelFrameworkModulePkg.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Shumin Qiu <shumin.qiu@intel.com>
Count is initially 1 but is assigned to 2 in case PS2_READ_DATA_BYTE.
Though the state machine doesn't go back from PS2_READ_DATA_BYTE to
PS2_READ_BYTE_ONE (not a true bug), force assign Count to 1 to avoid
potential buffer overflow issue.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Shumin Qiu <shumin.qiu@intel.com>
In PerformanceLib, Identifier is for single PERF, not the pair of PERF.
When find the matched START and END pair, the identifier will not be checked.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
gEfiPs2PolicyProtocolGuid and PcdFastPS2Detection was missed when
resolving the conflict.
Check in the two definition to MdeModulePkg.dec to fix build failure.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Add 2 macros inNetLib.h
#define IP4_MASK_MAX 32
#define IP6_PREFIX_MAX 128
we will use these two macros to check the max mask/prefix length,
instead of
#define IP4_MASK_NUM 33
#define IP6_PREFIX_NUM 129
which means a valid number.
This will make the code readability and maintainability.
Cc: Subramanian Sriram <sriram-s@hpe.com>
Cc: Fu Siyuan <siyuan.fu@intel.com>
Cc: Ye Ting <ting.ye@intel.com>
Cc: Wu Jiaxin <jiaxin.wu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Zhang Lubo <lubo.zhang@intel.com>
Reviewed-by: Sriram Subramanian <sriram-s@hpe.com>
Redfine the BmIsValidLoadOptionVariableName function to allow public use. Change name to EfiBootManagerIsValidLoadOptionVariableName to match naming scheme. Check that VariableName is never NULL and allow OptionType and OptionNumber to be optional.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Thomas Palmer <thomas.palmer@hpe.com>
Reviewed-by: Sunny Wang <sunnywang@hpe.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
The S3Ready() functional code in AcpiS3SaveDxe of IntelFrameworkModulePkg
is to do ACPI S3 Context save. In fact, that is not really related to
Intel framework ACPI S3 protocol.
IntelFrameworkModulePkg will be deprecated step by step, so move the
functional code to MdeModulePkg and S3SaveStateDxe is a good place.
The ACPI global variable related code is leaved as is in IntelFrameworkModulePkg
AcpiS3SaveDxe for compatibility.
PcdS3BootScriptStackSize is also moved from IntelFrameworkModulePkg.
The functional code need to get ACPI FACS table and consume LockBoxLib,
so need to be before DxeSmmReadyToLock that will shut down SMM lock box
interface, EndOfDxe is a good point (OVMF AcpiS3SaveDxe has the reference
implementation).
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Platform can configure the PCD statically or dynamically
to control if ACPI S3 will be enabled.
S3 related modules can consume the PCD to control the code.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
MemoryTypeInformation don't count the reserved memory used by RAM Disk,
but it still check all types of memory and do reset when any type
of memory size changes.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Siyuan Fu <siyuan.fu@intel.com>
Reviewed-by: Samer El-Haj-Mahmoud <elhaj@hpe.com>
The resource free includes to un-register the ram disk device and
free the memory occupied by the ram disk.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Siyuan Fu <siyuan.fu@intel.com>
Reviewed-by: Samer El-Haj-Mahmoud <elhaj@hpe.com>
Use reserved memory to hold the buffer for the RAM disk to
follow the ACPI spec requirement.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Siyuan Fu <siyuan.fu@intel.com>
Reviewed-by: Samer El-Haj-Mahmoud <elhaj@hpe.com>
This change mirrors the change in InteFrameworkModulePkg.
We now account for all TYPE19 memory regions found in the
smbios data, as well as handling records with Extended Addresses.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Commit 1b31acb66c ("MdeModulePkg: Check received packet size before use
it.") introduced a chunk of code under the new "Resume" label, in function
UdpIoOnDgramRcvdDpc(). The new code is supposed to run only when the
received packet has zero-length payload, but a "return" statement was
forgotten, and the code is reached on the normal (nonzero-length payload)
path as well, after the packet has been processed (and possibly freed) by
RxToken->CallBack(). This is a logic bug, with the direct symptom being
use-after-free / General Protection Fault.
Cc: Siyuan Fu <siyuan.fu@intel.com>
Cc: Jiaxin Wu <jiaxin.wu@intel.com>
Cc: Ting Ye <ting.ye@intel.com>
Cc: "Subramanian, Sriram (EG Servers Platform SW)" <sriram-s@hpe.com>
Fixes: 1b31acb66c
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Sriram Subramanian <sriram-s@hpe.com>
Arbitrary length of packet may be received from network, including the
packets with zero payload data or malformed protocol header. So the code
much check the actually received data size before using it. For example, in
current edk2 network stack, an zero payload UDP packet may cause the
platform ASSERT in NetbufFromExt() because of the zero fragment number.
This patch update the IpIoLib and UdpIoLib to check and discard the zero
payload data packet to avoid above assert. Some other network drivers are
also updated to check the packet size to guarantee the minimum length of
protocol header is received from upper layer driver.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Fu Siyuan <siyuan.fu@intel.com>
Reviewed-by: Sriram Subramanian <sriram-s@hpe.com>
Reviewed-by: Wu Jiaxin <jiaxin.wu@intel.com>
This reverts commit 31ae446b1a.
Changing the receive FIFO depth in Terminal driver Start() is not
recommended.
A new PCD PcdUartDefaultReceiveFifoDepth was added and
MdeModulePkg/SerialDxe driver uses the PCD as the default receive
FIFO depth.
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Ryan Harkin <ryan.harkin@linaro.org>
EndingAddress is calculated incorrectly. Original code calculates it as
(StartingAddress + Size). Correct value should be (StartingAddress +
Size - 1.
Note:
Besides the changes made by Samer, Hao also fixed a similar issue in
RamDiskImpl.c
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Samer El-Haj-Mahmoud <elhaj@hpe.com>
Signed-off-by: Tapan Shah <tapandshah@hpe.com>
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Tapan Shah <tapandshah@hpe.com>
Check for NULL from AllocateCopyPool before setting Count to 1. Also
change sizeof (EFI_HANDLE*) to sizeof (EFI_HANDLE). Handles is a
EFI_HANDLE pointer, so the allocated memory must be the size of
EFI_HANDLE.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Thomas Palmer <thomas.palmer@hpe.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
This stack includes:
1. Dxe phase support by:
1) SdMmcPciHcDxe driver to consume PciIo and produce
SdMmcPassThru.
2) SdDxe driver to consume SdMmcPassThru to produce
BlkIo1/BlkIo2.
3) EmmcDxe driver to consume SdMmcPassThru to produce
BlkIo1/BlkIo2/SSP.
2. Pei phase support
1) SdBlockIoPei driver to consume SdMmcHostController
Ppi and produce VirutalBlkIo1&2.
2) EmmcBlockIoPei driver to consume SdMmcHostController
Ppi and produce VirutalBlkIo1&2.
3) SdMmcPciHcPei driver to produce SdMmcHostController
Ppi.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Hao Wu <hao.a.wu@intel.com>
There are scenario when the BindingStop service of PartitionDxe driver be
re-entered.
An example will be ejecting a DVD from a SATA DVDROM and then run
"reconnect -r" under shell. In this specific case, part of the calling
stack will be:
PartitionDriverBindingStop() (PartitionDxe) ->
Stop first child handle (PartitionDxe) ->
ScsiDiskFlushBlocksEx() (ScsiDiskDxe) ->
A media change is detected (ScsiDiskDxe) ->
Reinstall of BlockIO(2) protocols (ScsiDiskDxe) ->
Entering PartitionDriverBindingStop() again (PartitionDxe) ->
Potential risk of referencing already stopped child handle (PartitionDxe)
...
The current code has potential issue of referencing of already stopped
child handle. This commit adds re-entry handling logic to resolve such
issue.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Set UART receive FIFO depth with PCD instead of fixed number "1".
The default value of PCD is also 1, so it makes no difference for
platforms which do not explicitly set this PCD.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Heyi Guo <heyi.guo@linaro.org>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Found an issue that file system cannot be started on a DVD when doing the
following process:
Boot to shell with a DVD inside a SATA DVDROM. Eject the DVD and run
"reconnect -r". Put the DVD inside again and run "reconnect -r".
The cause is that after executing the second reconnect action, DiskIo
immediately returns EFI_NO_MEDIA in function DiskIo2ReadWriteDisk() when
checking the media information. However, at this time, the media
information does not get updated by the ScsiDisk driver. Therefore, DiskIo
driver should left the no media check to ScsiDisk driver.
Generally, the media changed and media write protect check should also be
left to lower-level device driver. Thus, these two checks in function
DiskIo2ReadWriteDisk() are also removed.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Some ISO images cannot be recognized properly when they are on media whose
block size is not 2048 bytes.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
The 'Reset' function for BlockIO(2) in ScsiDiskDxe should return
EFI_SUCCESS instead of EFI_DEVICE_ERROR when a device does not support
reset feature.
Otherwise, a 'reconnect -r' action when an ISCSI device is attached will
cause system hang.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Remove variables that are declared, assigned but never referenced. This
fixes a warning emitted by GCC when -Wunused-but-set-variable is in effect.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
When there is no bridge before the HPC (hot plug controller),
the issue cannot be seen.
But when there are bridges before the HPC, the PciBus will only
use the value (= <CurrentBusNumber> + <ReservedBusNumber>) as the
sub-ordinary bus number for HPC.
The correct sub-ordinary bus number should be:
<CurrentBusNumber> + <OccupiedBusNumber>(by earlier bridges) +
<ReservedBusNumber>.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
Xcode clang seems unhappy with both FileExplorerLib.h and
Protocol/FileExplorer.h both defining CHOOSE_HANDLER, now
remove the definition in FileExplorerLib.h.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Andrew Fish <afish@apple.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
The type casting is not necessary and now remove it.
Cc: Liming Gao <liming.gao@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Gary Lin <glin@suse.com>
The BootMaintenanceManagerUiLib use ChooseFile() from FileExplorerLib
to select files. And the third parameter in ChooseFile() is CHOOSE_HANDLER,
per the definition of CHOOSE_HANDLER, it must use EFIAPI as the calling
convention. But the calling convention was not specified for following
handlers: CreateBootOptionFromFile, CreateDriverOptionFromFile,
BootFromFile. Now specifies the calling convention for those functions.
Cc: Liming Gao <liming.gao@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Gary Lin <glin@suse.com>
There is no asynchronous operations to the registered RAM disks link list
maintained within RamDiskDxe driver, therefore, the TPL raise and restore
operations when dealing with the link list are unnecessary.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Previously, the code uninstalls the DEVICE_PATH_PROTOCOL with the device
path given by caller of the 'RamDiskUnregister' function. The given device
path might be different from the one used to install the
DEVICE_PATH_PROTOCOL.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
The 'DisconnectController' function calls after
'UninstallMultipleProtocolInterfaces' are unnecessary, since
'DisconnectController' is called inside function
'UninstallMultipleProtocolInterfaces'.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Check for Type AllocateAddress,
if NumberOfPages is 0 or
if (NumberOfPages << EFI_PAGE_SHIFT) is above MAX_ADDRESS or
if (Start + NumberOfBytes) rolls over 0 or
if Start is above MAX_ADDRESS or
if End is above MAX_ADDRESS,
return EFI_NOT_FOUND.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Do not locate VarCheck protocol in Constructor, then the
gEdkiiVarCheckProtocolGuid could be removed from [Depex].
It will be more flexible for the library Consumer to work without VarCheck
protocol installed, for example at recovery boot mode with EmuRuntimeDxe.
The unused UefiLib is also been removed from [LibraryClasses] in *.inf.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
In UEFI2.6, CapturePtr's in the Captures array returned by MatchString
are to be separatedly allocated so that they can be freed by the
caller.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Cecil Sheng <cecil.sheng@hpe.com>
Reviewed-by: Samer El-Haj-Mahmoud <elhaj@hpe.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
This is an emergency fix for UINT64 multiplications and divisions not
being done with the right BaseLib functions -- they break Ia32 builds.
Fixes: 30ed3422ab
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
ConSplitter's Absolute Pointer should scale virtual device's resolution like what Simple Pointer do.
Before this change, caller will get Virtual device's resolution but physical device's current point.
This change let caller get Virtual device's resolution with virtual device's current point.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Derek Lin <derek.lin2@hpe.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Remove the ASSERT in UI code that may be triggered,
and clean up the useless code.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
In DriverSampleInit, has installed the configAccess protocol to
the DriverHandle[1], but don't uninstall it in DriverSampleUnload.
Now uninstall the configAccess protocol.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Commit 7c50b34343 introduced
PcdMaxPeiPerformanceLogEntries16 to support > 256 PEI performance log
entries, but its PROMPT&HELP STR were forgotten to be added into *.uni.
Commit 7c50b34343 also updated
PcdMaxPeiPerformanceLogEntries HELP STR.
This patch is to add PcdMaxPeiPerformanceLogEntries16 PROMPT&HELP STR and
update PcdMaxPeiPerformanceLogEntries HELP STR in *.uni.
Cc: Shumin Qiu <shumin.qiu@intel.com>
Cc: Cinnamon Shia <cinnamon.shia@hpe.com>
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Shumin Qiu <shumin.qiu@intel.com>
Reviewed-by: Cinnamon Shia <cinnamon.shia@hpe.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Since PcdHiiOsRuntimeSupport has added in the MdeModulePkg.dec file,
now add the usage information in the uni file.
Cc: Qiu Shumin <shumin.qiu@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Qiu Shumin <shumin.qiu@intel.com>
There some usefull functions in edk2 private modules that could be used,
so we added them to the httpLib
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ghazi Belaam <Ghazi.belaam@hpe.com>
Reviewed-by: Jiaxin Wu <jiaxin.wu@intel.com>
Reviewed-by: Samer EL-Haj-Mahmoud <elhaj@hpe.com>
Reviewed-by: Fu Siyuan <siyuan.fu@intel.com>
The maximum number of PEI performance log entries is 255.
Add a new PCD, PcdMaxPeiPerformanceLogEntries16, to increase the maximum
number of PEI performance log entries.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Cinnamon Shia <cinnamon.shia@hpe.com>
Reviewed-by: Samer EL-Haj-Mahmoud <elhaj@hpe.com>
Reviewed-by: Joseph Shifflett <joseph.shifflett@hpe.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Some static scan tool may regard CurrentRsdtEntry to be potentially
referenced to NULL pointer if CurrentRsdtEntry == NULL is used in
the right above if condition judgment.
CopyMem (CurrentRsdtEntry, CurrentRsdtEntry + 1, (*NumberOfTableEntries - Index) * sizeof (UINT32));
It is introduced by commit f9bbb8d9c3.
To avoid it and have same style with
"((Xsdt == NULL) || CurrentTablePointer64 == (UINT64) (UINTN) Table->Table)",
use Rsdt instead of CurrentRsdtEntry to check against NULL.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Shumin Qiu <shumin.qiu@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Shumin Qiu <shumin.qiu@intel.com>
The patch enhances the UefiBootManagerLib to use more user-friendly
network boot option description.
It builds description like below:
"PXEv6 (MAC:112233445566 VLAN1)"
"HTTPv4 (MAC:112233445566)"
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Siyuan Fu <siyuan.fu@intel.com>
1. The consumer of Acpi Sdt Protocol may want to use the API after ReadyToLock.
2. The ACPI system configuration table even could be overwritten,
we see little issue in leaving Acpi Sdt Protocol installed.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Failing to set EFI_MEMORY_UC to MMIO aperture is not a fatal error.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Enhance BDS to support booting from a remote file system exposed
by a HTTP boot option.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Sunny Wang <sunnywang@hpe.com>
The patch adds short-form URI boot support to follow
UEFI Spec.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Sunny Wang <sunnywang@hpe.com>
Enhance BDS to wide match the HTTP boot option without matching
the specific device path data in IP device path and URI device
path node.
It's to follow UEFI Spec 2.6.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Sunny Wang <sunnywang@hpe.com>
Change BmGetFileBufferByMemmapFv to BmGetFileBufferByFvFilePath.
The original function gets the file buffer only from memory mapped
FV device path and leaves GUIDed FV device path to the code below;
The new function gets the file buffer from both formats of FV device
paths.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Sunny Wang <sunnywang@hpe.com>
Fix a possible ASSERT after NBP finishes loading from a PXE
boot. Ip4Dxe driver calls Ip4Config2SetPolicy which calls
CloseEvent on the Dhcp4Event struct member. After NBP is
downloaded, it then calls Ip4Config2CleanInstance which calls
CloseEvent again on Dhcp4Event. This double free can cause an
ASSERT. When the event is closed, set the event pointer to NULL
so the Ip4 code won't call CloseEvent on it again.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Samer El-Haj-Mahmoud <elhaj@hpe.com>
Reviewed-by: Ye Ting <ting.ye@intel.com>
Reviewed-by: Fu Siyuan <siyuan.fu@intel.com>
This feature is aimed to allow OS make use of the HII database
during runtime. In this case, the contents of the HII Database
is exported to a buffer. The pointer to the buffer is placed
in the EFI System Configuration Table, where it can be retrieved
by an OS application.
Cc: Liming Gao <liming.gao@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Brian J. Johnson <bjohnson@sgi.com>
Cc: Andrew Fish <afish@apple.com>
Cc: El-Haj-Mahmoud Samer <samer.el-haj-mahmoud@hpe.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Remove the empty line to conform with current coding style.
Cc: Qiu Shumin <shumin.qiu@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
The "pc" ("pc-i440fx-*") machine types of QEMU don't support extended
config space. Accordingly, OVMF will use the following library instances
in connection with the core PciHostBridgeDxe driver:
BasePciSegmentLibPci [class: PciSegmentLib]
BasePciLibCf8 [class: PciLib]
BasePciCf8Lib [class: PciCf8Lib]
Add a new field to the PCI_ROOT_BRIDGE structure so that
RootBridgeIoCheckParameter() can catch config space offsets above 0xFF on
such old (emulated) platforms.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Marcel Apfelbaum <marcel@redhat.com>
Cc: Michael Kinney <michael.d.kinney@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
... in preparation for the next patch.
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Michael Kinney <michael.d.kinney@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
The device path protocol doesn't get closed at FvSimpleFilesystem
driver stop() when it's opened at start() with BY_DRIVER mode.
We change it to open DevicePath with GET_PROTOCOL mode as FV2 protocol with BY_DRIVER is enough.
Cc: Chao Zhang <chao.b.zhang@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Chao Zhang <chao.b.zhang@intel.com>
Git version '3d0a49ad' commit provided a scenario to resolve the
performance issue for IPv4, but it's not workable for IPv6. To
avoid IPv4 and IPv6 inconsistency, we decided to revert that version
fix.
If so, the default policy for Ip4Config2 is Ip4Config2PolicyDhcp,
which results in all NIC ports attempting DHCP. So, this patch is
used to changes the the default IPv4 config policy to
Ip4Config2PolicyStatic and also defer the SetData operation after
Ip4Config2Protocol installed. This update let the other platform
drivers have chance to change the default config data by consume
Ip4Config2Protocol.
Cc: Subramanian Sriram <sriram-s@hpe.com>
Cc: El-Haj-Mahmoud Samer <samer.el-haj-mahmoud@hpe.com>
Cc: Ye Ting <ting.ye@intel.com>
Cc: Fu Siyuan <siyuan.fu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiaxin Wu <jiaxin.wu@intel.com>
Reviewed-by: Subramanian Sriram <sriram-s@hpe.com>
Reviewed-by: Fu Siyuan <siyuan.fu@intel.com>
Reviewed-by: Ye Ting <ting.ye@intel.com>
Currently the EFI_FILE_EXPLORE_FORMSET_GUID value in BdsDxe in
IntelFrameworkModulePkg is same with the GUID VALUE in FileExplorerLib.
This patch is to modify the EFI_FILE_EXPLORE_FORMSET_GUID in
FileExplorerLib to avoid potential issue.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
when free up resource allocated for a MenuEntry, there exists
the case that the DevicePath and DisplayString are NULL,
so before calling FreePool function, need to check.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
When the DXE core is loaded, it invokes the PeCoffExtraActionLib library
function 'PeCoffLoaderRelocateImageExtraAction' explicitly, which may be
in addition to the same function having been called by the DxeIpl PE/COFF
loader instance.
The ImageContext that DXE core presents to this function is only partially
initialized, which may result in the following output on AArch64 systems:
add-symbol-file ..MdeModulePkg/Core/Dxe/DxeMain/DEBUG/DxeCore.dll 0x5F226240
<some intermediate output>
add-symbol-file ..MdeModulePkg/Core/Dxe/DxeMain/DEBUG/DxeCore.dll 0x5F226000
This is caused by incorrect data in the ImageContext structure, which means
the start of the .text section is calculated incorrectly. In general, it is
the duty of the caller to present a valid ImageContext structure, so let's
add the missing values before invoking PeCoffLoaderRelocateImageExtraAction().
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Star Zeng <star.zeng@intel.com>
This patch is to add a new interface to get the "Path" component according to
the URI parse result, it would be helpful for the library user to extract the
file path value in a URI.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Fu Siyuan <siyuan.fu@intel.com>
Reviewed-by: Wu Jiaxin <jiaxin.wu@intel.com>
Reviewed-by: Ye Ting <ting.ye@intel.com>
The StringSize variable in the FindStringBlock function is a IN OUT
parameter of the GetUnicodeStringTextOrSize function.
Thought the GetUnicodeStringTextOrSize function changes the value of
the StringSize variable, it is better to initialize the StringSize
variable before passing it to the GetUnicodeStringTextOrSize function.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Cinnamon Shia <cinnamon.shia@hpe.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
When PcdShadowPeimOnBoot is FALSE, they are not copied to memory and
execute from their original locations. Here, this policy should only
apply for PEIM and PEI_CORE, not for other file type, such as DXE_CORE.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Tested-by: Eugene Cohen <eugene@hp.com>
The RamDiskDxe driver will:
1. Produce the EFI RAM Disk Protocol
2. Install RAM disk device path and block I/O related protocols on the
RAM disk device handle.
3. Install RAM disk configuration form to HII database
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Samer El-Haj-Mahmoud <elhaj@hpe.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Some platform doesn't use CPU(HOST)/Device 1:1 mapping for PCI Bus.
But PCI IO doesn't have interface to tell caller (device driver)
whether the address returned by GetBarAttributes() is HOST address
or device address.
UEFI Spec 2.6 addresses this issue by clarifying the address returned
is HOST address and caller can use AddrTranslationOffset to calculate
the device address.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
For new PCDs add their usage information strings in UNI file.
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: "Yao, Jiewen" <jiewen.yao@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Qiu Shumin <shumin.qiu@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
v3:
*
When there exists duplicate items in VLAN variable , save the correct
variable content back to the variable storage after duplicate items are removed
Duplicate items in VLAN variable will cause MNP driver binding
start function fall into infinite loop,so we should check it's
content before using it.
Cc: Fu Siyuan <siyuan.fu@intel.com>
Cc: Ye Ting <ting.ye@intel.com>
Cc: Wu Jiaxin <jiaxin.wu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Zhang Lubo <lubo.zhang@intel.com>
Reviewed-by: Ye Ting <ting.ye@intel.com>
Reviewed-by: Fu Siyuan <siyuan.fu@intel.com>
Reviewed-by: Wu Jiaxin <jiaxin.wu@intel.com>
The ISO C standard says about free(),
If ptr is a null pointer, no action occurs.
This is not true of the FreePool() interface of the MemoryAllocationLib
class:
Buffer must have been allocated on a previous call to the pool
allocation services of the Memory Allocation Library. [...] If Buffer
was not allocated with a pool allocation function in the Memory
Allocation Library, then ASSERT().
Therefore we must not forward the argument of free() to FreePool() without
checking.
Cc: Cecil Sheng <cecil.sheng@hpe.com>
Cc: Cinnamon Shia <cinnamon.shia@hpe.com>
Cc: Eric Dong <eric.dong@intel.com>
Cc: Qiu Shumin <shumin.qiu@intel.com>
Cc: Samer El-Haj-Mahmoud <elhaj@hpe.com>
Cc: Yao Jiewen <Jiewen.Yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-By: Cinnamon Shia <cinnamon.shia@hpe.com>
The assignment of CurrentRsdtEntry and its subsequent dereference are
subject to the same condition, but for some reason, VS2008 does not see
that and warns about the dereference possibly involving an uninitialized
pointer. Since the single statememt between the blocks is unrelated, we
can just move it and merge the two conditional blocks together.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: David Woodhouse <David.Woodhouse@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
The patch removes the assumption that the resources claimed by root
bridges should not exist. Because resources might have been added:
1. by platform modules either in PEI through resource HOB, or in DXE,
before the PCI host bridge driver runs.
2. Resources claimed by different root bridges may overlap so that
resource adding operation for latter root bridges may fail if
we assume the resource should not exist.
In real world, this patch is to fit OVMF platform needs because
different root bridges in OVMF platform shares the same resources.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
[lersek@redhat.com: intersection-based implementation]
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
If 'CoreGetMemoryMap' return success the 'MemoryMap' shouldn't be NULL.
Add code to make sure this.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Qiu Shumin <shumin.qiu@intel.com>
Reviewed-by: Yao Jiewen <Jiewen.Yao@intel.com>
Now we add new HII action type EFI_BROWSER_ACTION_SUBMITTED in
EFI HII Configuration Access Protocol, so add the test case in
DriverSample to show how to use it and whether it works.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Add new HII action type EFI_BROWSER_ACTION_SUBMITTED
to notify HII driver when its question values are submitted.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
According to the spec, each entry in the Memory
Attributes table shall have the same type as
the region it was carved out of in the UEFI memory map.
The current attribute uses RTData for PE Data, but
it should be RTCode.
This patch fixed the issue. It is validated with or
without PropertiesTable.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: "Yao, Jiewen" <jiewen.yao@intel.com>
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Liming Gao <liming.gao@intel.com>
This is caused by my last commit,the LoadOption may
not initialize when call FreePool, and after investigation,
find that we can delete the LoadOption variable, this patch
is to fix this issue.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
AARCH64 systems never require compatibility with legacy ACPI OSes, and
may not have any 32-bit addressable system RAM. To support ACPI on these
systems, we need to be able to relax the 4 GB allocation restriction.
So add a PCD PcdAcpiExposedTableVersions containing a bitmask describing
which ACPI versions are targeted, and wire it up it up to the memory
allocation calls in AcpiTableDxe/AcpiTableProtocol.c. I.e., if ACPI v1.0b
is not among the supported versions, the memory allocations are not limited
to 4 GB, and only table types that carry 64-bit addresses are emitted.
Note that this will inhibit the publishing of any tables that carry only
32-bit addresses, i.e., RSDPv1, RSDTv1 and RSDTv3.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: "Yao, Jiewen" <jiewen.yao@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Since Shell supports finding help information from resource section
of application image. We enhance the HelloWorld to add help information
string. After the HelloWorld are loaded in system the help string will
be stored in resource section of the application image.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Jaben Carsey <jaben.carsey@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Qiu Shumin <shumin.qiu@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Refine the code in function Var_UpdateDriverOption and Var_UpdateBootOption,
use the existed API(EfiBootManagerInitializeLoadOption and
EfiBootManagerAddLoadOptionVariable) supplied by UefiBootManagerLib
to replace the same logic in the two functions. And remove the useless
code.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
when has next line to draw, should not overwrite the BltX
to 0, instead should keep the BltX value that pass into
StringToImage function.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
UEFI Spec 2.3.1.D Section 9.3.5.1 says Partitions are numbered
according to their entry in their respective partition table,
starting with 1.
Update the code for MBR partition to follow this rule.
Ref: https://github.com/tianocore/edk2/issues/50
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
FALSE
UEFI2.6 specification does not recommend to use BIT0
attribute for PropertiesTable, so we change default
value to FALSE.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: "Yao, Jiewen" <jiewen.yao@intel.com>
Reviewed-by: "Gao, Liming" <liming.gao@intel.com>
Reviewed-by: "Ard Biesheuvel" <ard.biesheuvel@linaro.org>
Reviewed-by: "Laszlo Ersek" <lersek@redhat.com>
This patch is used to define a general function to create
DNS QName.
QName is a domain name represented as a sequence
of labels, where each label consists of a length octet
followed by that number of octets. The domain name terminates
with the zero length octet for the null label of the root.
Cc: Hegde Nagaraj P <nagaraj-p.hegde@hpe.com>
Cc: El-Haj-Mahmoud Samer <samer.el-haj-mahmoud@hpe.com>
Cc: Ye Ting <ting.ye@intel.com>
Cc: Fu Siyuan <siyuan.fu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiaxin Wu <jiaxin.wu@intel.com>
Reviewed-by: Hegde Nagaraj P <nagaraj-p.hegde@hpe.com>
Reviewed-by: Fu Siyuan <siyuan.fu@intel.com>
Reviewed-by: Ye Ting <ting.ye@intel.com>
This patch fixes a bug in SNP driver that the Cdb.StatCode should be check with
PXE_STATCODE_SUCCESS instead of EFI_SUCCESS.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Fu Siyuan <siyuan.fu@intel.com>
Reviewed-by: Jiaxin Wu <jiaxin.wu@intel.com>
Reviewed-by: Ye Ting <ting.ye@intel.com>
SNP driver will print the UNDI returned StatFlags:StatCode with DEBUG macro,
while in some please it uses the reverse order (StatCode:StatFlags). This patch
is to make the print info consistent, that StatFlags always come first.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Fu Siyuan <siyuan.fu@intel.com>
Reviewed-by: Jiaxin Wu <jiaxin.wu@intel.com>
Reviewed-by: Ye Ting <ting.ye@intel.com>
MemoryAttributesTable generation need information in
PropertiesTable.
In memory attributes table generation path,
PropertiesTable need record original memory map and do
not merge the new memory map entry cross original
memory map boundary.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: "Yao, Jiewen" <jiewen.yao@intel.com>
Reviewed-by: "Gao, Liming" <liming.gao@intel.com>
Add MemoryAttributesTable generation in DxeCore.
We leverage the information collected by original
PropertiesTable, and publish runtime code/data to
another standalone table. So that this is a
compatible solution to report more PE Code/Data
information.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: "Yao, Jiewen" <jiewen.yao@intel.com>
Reviewed-by: "Gao, Liming" <liming.gao@intel.com>
Refine the function comments in ConfigKeywordHandler.c and
HiiDatabase.h.
Cc: Liming Gao <liming.gao@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
At the end of CoreFreePoolI(), the check to see if it is a specific
memory type should also cover OEM reserved memory type.
It was missed when adding OEM reserved memory type support at R17460.
Cc: Liming Gao <liming.gao@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
If FV image without DXE depex, it will be dispatched by DxeCore.
If FV image with SMM depex, it is the invalid image. ASSERT will be trig.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Andrew Fish <afish@apple.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Fix UsbMouseAbsolutePointer driver GetState() interface to return
absolute value instead of relative value.
The driver is ported from UsbMouse driver. The GetState of
SimplePointer protocol returns relative value but the GetState
of AbsolutePointer protocol should return absolute value.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
According to UEFI spec, a BUFFER_FULL return status in UNDI Transmit command
indicates UNDI "Transmit buffer is full. Call Get Status command toempty
buffer." So this patch updates the SNP Transmit to return EFI_NOT_READY for
BUFFER_FULL to let the call know the buffer full status.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Fu Siyuan <siyuan.fu@intel.com>
Reviewed-by: Sriram Subramanian <sriram-s@hpe.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ye Ting <ting.ye@intel.com>
The MNP and SNP are independent drivers so the MNP_TX_BUFFER_INCREASEMENT could choose
any value as needed. While this patch update the default value of this macro to 32,
to be same as the maximum recycled buffer numbers in one UNDI GetStatus command. It is
a workaround for some incorrect UNDI drivers which may not return the correct statuses
for the SNP and MNP to correctly retry/call GetStatus to clear the buffers.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Fu Siyuan <siyuan.fu@intel.com>
Reviewed-by: Sriram Subramanian <sriram-s@hpe.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ye Ting <ting.ye@intel.com>
Update the DBsize in GetStatus command to let UNDI return an array of recycled
buffers. This is to make the loop at the end of PxeGetStatus() useful and to
prevent buffer overflow with some non-conformant UNDI drivers which not check
the value of the input DBsize in UNDI GetStatus command.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Fu Siyuan <siyuan.fu@intel.com>
Reviewed-by: Sriram Subramanian <sriram-s@hpe.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ye Ting <ting.ye@intel.com>
Description of the GetNextHighMonotonicCount does not state that the counter
is incremented on calling this function. However, the example usage of this
API documented relies on this behavior.
UEFI 2.6 spec is to update description to match usage documented.
The high 32-bit value is nonvolatile and is increased by 1 whenever the system
resets whenever the low 32-bit count (returned by GetNextMonoticCount()) overflows.
->
The high 32-bit value is nonvolatile and is increased by 1 whenever the system
resets, whenever GetNextHighMonotonicCount() is called, or whenever the low
32-bit count (returned by GetNextMonoticCount()) overflows.
Cc: Liming Gao <liming.gao@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19773 6f19259b-4bc3-4df7-8a09-765794883524
UEFI 2.6 spec has minor update to the Data parameter for GetVariable(),
and no real functional behavior change.
The modifier of Data parameter:
OUT VOID *Data
->
OUT VOID *Data OPTIONAL
The comments of Data parameter:
Data The buffer to return the contents of the variable.
->
Data The buffer to return the contents of the variable. May be NULL
with a zero DataSize in order to determine the size buffer needed.
The patch is to follow the spec to update the implementation.
Cc: Liming Gao <liming.gao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19771 6f19259b-4bc3-4df7-8a09-765794883524
These workhorse functions are part of the BlockIo protocol that
NvmExpressDxe produces. For bulk data access, they are called very
frequently. Their debug messages should be therefore downgraded to
EFI_D_VERBOSE.
In addition, the following DEBUG() warts are cleaned up:
- The function name should be printed with %a / __FUNCTION__, so that
renaming the function, or copying the DEBUG() elsewhere, be reflected in
the debug output automatically. (In fact, after this patch, the DEBUG()
calls become identical.)
- "Lba" is of type UINT64, therefore it should be printed with %Lx, not
%x.
- "OrginalBlocks" and "Blocks" are both UINTN. The only portable way to
print UINTN is to convert it to UINT64 manually, then format it with the
%Lx (or %Lu) conversion specifier.
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Feng Tian <feng.tian@Intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19763 6f19259b-4bc3-4df7-8a09-765794883524
(HandoffInformationTable->EfiFreeMemoryBottom - Private->HobList.Raw)
is the PEI temp heap used instead of the length of PEI temp heap.
The length of PEI temp heap should be:
(HandoffInformationTable->EfiFreeMemoryTop - Private->HobList.Raw)
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Cinnamon Shia <cinnamon.shia@hpe.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19762 6f19259b-4bc3-4df7-8a09-765794883524
Signal a closed event will still invoke the event notification function,
it could only be exposed when no the DEBUG_PROPERTY_CLEAR_MEMORY_ENABLED
bit set in PcdDebugPropertyMask.
For example:
gBS->CreateEvent (
EVT_NOTIFY_SIGNAL,
TPL_CALLBACK,
CallbackFun,
NULL,
&Event
);
gBS->CloseEvent (Event);
gBS->SignalEvent (Event); <- CallbackFun still be invoked
Although the case to signal a closed event is abnormal, the code could
still be enhanced to avoid it.
Cc: Liming Gao <liming.gao@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Thomas Palmer <thomas.palmer@hpe.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19754 6f19259b-4bc3-4df7-8a09-765794883524
String opcode has HiiValue and BufferValue,BufferValue for string content,
HiiValue for StringId.Function GetQuestionValue only update the
BufferValue(string content),but the StringId and string content
do not match,now fix this issue.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19750 6f19259b-4bc3-4df7-8a09-765794883524
The BlockData is expected to be NULL when to call function
IsThisOpcodeRequired in each opcode,but now exists case that the
Blockdata not be cleaned,then will be used in other opcode.it
is not correct,now add the check before use.
The comments and logic in function IsThisOpcodeRequired are not
consistent,now refine the code to make the logic clear.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19749 6f19259b-4bc3-4df7-8a09-765794883524
For some SCSI commands, notably INQUIRY, it's relatively common for
the device to provide less data than we intended to read, and for
this reason EFI_EXT_SCSI_PASS_THRU_SCSI_REQUEST_PACKET makes
InTransferLength and OutTransferLength read-write. Make ATAPI
aware of this.
This makes it possible to handle EFI_NOT_READY always, not just
for read as done in r19685.
I've chosen to use a break statement instead of calling
CheckStatusRegister directly; the break statement reaches a
pre-existing call the CheckStatusRegister function. This
ensures that the assignment to *ByteCount is not missed, and
adds a further sanity check to DRQClear.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19737 6f19259b-4bc3-4df7-8a09-765794883524
The Serial IO protocol instances provided by SerialDxe and consumed by
TerminalDxe come with a Mode.ReceiveFifoDepth=1 default setting, as
required by UEFI 2.5.
Although TerminalDxe calls EFI_SERIAL_IO_PROTOCOL.SetAttributes() in the
TerminalDriverBindingStart() and TerminalConInTimerHandler() functions, it
only does so to change the Mode.Timeout member. Other members of Mode,
including Mode.ReceiveFifoDepth, are preserved.
On some platforms this causes the UART that underlies TerminalDxe not to
have enough room for bursts of scan codes, which translates to broken
parsing of escape sequences, e.g. cursor movement keys.
According to the UEFI spec, passing ReceiveFifoDepth=0 to
EFI_SERIAL_IO_PROTOCOL.SetAttributes() "will use the device's default FIFO
depth". While TerminalDxe could try to configure a receive FIFO depth that
matches the longest escape sequence it wishes to parse, in practice the
device-specific default FIFO depth -- which may well differ from the
spec-mandated SerialIo->Mode.ReceiveFifoDepth=1 default -- seems to work.
Hence let's just set that.
This issue was exposed by SVN r18971 / git commit 921e987b2b
("ArmPlatformPkg: Use SerialDxe in MdeModulePkg instead of EmbeddedPkg").
In that conversion, MdeModulePkg's SerialDxe started to initialize
Mode.ReceiveFifoDepth to 1 (in conformance with the spec), unlike the
prior, non-conformant initialization to 0 in EmbeddedPkg's SerialDxe.
Since TerminalDxe would never change ReceiveFifoDepth from the new default
value 1, and the ArmPlatformPkg/Drivers/PL011Uart library instance,
underlying SerialDxe through SerialPortLib, would obey it too, they would
collectively effect a receive queue depth of 1, rather than the default 16
or 32. This broke cursor keys on the ARM FVP and Juno platforms.
It is the client of EFI_SERIAL_IO_PROTOCOL that is responsible for
modifying the attributes, if the defaults are not appropriate, hence this
patch modifies TerminalDxe.
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Ryan Harkin <ryan.harkin@linaro.org>
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Cc: Star Zeng <star.zeng@intel.com>
Reported-by: Ryan Harkin <ryan.harkin@linaro.org>
Reference: http://thread.gmane.org/gmane.comp.bios.edk2.devel/4779/focus=6553
Reference: http://thread.gmane.org/gmane.comp.bios.edk2.devel/6594
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19701 6f19259b-4bc3-4df7-8a09-765794883524
In "11.8 Serial I/O Protocol", UEFI 2.5 requires:
The default attributes for all UART-style serial device interfaces are:
(a) 115,200 baud,
(b) a 1 byte receive FIFO,
(c) a 1,000,000 microsecond timeout per character,
(d) no parity,
(e) 8 data bits,
(f) and 1 stop bit.
It also says, about the EFI_SERIAL_IO_MODE.ControlMask member:
(g) A mask of the Control bits that the device supports. The device must
always support the Input Buffer Empty control bit.
SerialDxe complies with requirement (b) via hard-coded constants. It
complies with requirements (a), (d), (e) and (f) through PCD defaults (see
MdePkg/MdePkg.dec):
(a) 115,200 baud:
gEfiMdePkgTokenSpaceGuid.PcdUartDefaultBaudRate|115200|UINT64|0x00000020
(d) no parity:
# 1 - No Parity.<BR>
gEfiMdePkgTokenSpaceGuid.PcdUartDefaultParity|1|UINT8|0x00000022
(e) 8 data bits:
gEfiMdePkgTokenSpaceGuid.PcdUartDefaultDataBits|8|UINT8|0x00000021
(f) 1 stop bit:
# 1 - One Stop Bit.<BR>
gEfiMdePkgTokenSpaceGuid.PcdUartDefaultStopBits|1|UINT8|0x00000023
SerialDxe does not comply with requirements (c) and (g). In this patch, we
fix (c), and leave (g) for later.
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Ryan Harkin <ryan.harkin@linaro.org>
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19700 6f19259b-4bc3-4df7-8a09-765794883524
Per secure MOR implementation document, it is not proper to add MOR lock in non-SMM version, because DXE version can not provide protection.
This patch add standalone TcgMorLockDxe implementation.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: "Yao, Jiewen" <jiewen.yao@intel.com>
Reviewed-by: "Zhang, Chao B" <chao.b.zhang@intel.com>
Reviewed-by: "Zeng, Star" <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19689 6f19259b-4bc3-4df7-8a09-765794883524
Microsoft published secure MOR implementation at https://msdn.microsoft.com/en-us/library/windows/hardware/mt270973(v=vs.85).aspx
with revision 2 update. See URL for tech detail.
Previous revision 1 is handled in SecurityPkg\Tcg\ MemoryOverwriteRequestControlLock.
But the VarCheck API can not satisfy revision 2 requirement.
So we decide include MOR lock control into variable driver directly.
This patch add standalone TcgMorLockSmm implementation.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: "Yao, Jiewen" <jiewen.yao@intel.com>
Reviewed-by: "Zhang, Chao B" <chao.b.zhang@intel.com>
Reviewed-by: "Zeng, Star" <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19688 6f19259b-4bc3-4df7-8a09-765794883524
SVN r19611 (git commit 7cac240163), "MdeModulePkg/Ide: return correct
status when DRQ is not ready for ATAPI", changed the behavior of
AtaPacketReadWrite(), when DRQReady2() reported an error. The previous
logic had been to:
(a) terminate the transfer loop,
(b) check the status register with CheckStatusRegister(), and determine
AtaPacketReadWrite()'s return code directly from that.
Action (a) had been correct, but action (b) had masked genuine errors.
For example, when DRQReady2() reported EFI_TIMEOUT -- because the BSY bit
had not been cleared within the allotted time --, CheckStatusRegister()
would report EFI_SUCCESS, simply *because* BSY was still set, and the rest
of the status bits could not be evaluated.
SVN r19611 (git commit 7cac240163) intended to fix action (b) by directly
propagating the error code of DRQReady2() from AtaPacketReadWrite(),
eliminating the CheckStatusRegister() call. This was the right thing for
most of the errors reported by DRQReady2() -- timeout, command abort,
other device error --, but there was one exception: the "read" sub-case of
EFI_NOT_READY, which stands for "'read' complete, with less data available
than the requested amount".
Regarding the "write" sub-case of EFI_NOT_READY: the
AtaPacketCommandExecute() function programs the full transfer length into
the IDE device before it calls AtaPacketReadWrite(), and
AtaPacketReadWrite() only uses CylinderLsb and CylinderMsb for "chunking"
(as requested by the device). Therefore the device cannot justifiedly
clear DRQ earlier than seeing the entire data, when writing.
However, when reading from the device, a "short read" is a successful
operation. (The actual read length will be decoded by the higher level
protocols.) And "short reads" had been handled correctly by the logic
before git 7cac240163. Namely, when DRQReady2() returns EFI_NOT_READY, the
BSY bit is already clear, and we can call CheckStatusRegister() to
investigate all the other bits it cares about.
Therefore restore the logic from before git 7cac240163, but only for the
"read" sub-case of EFI_NOT_READY.
This problem was encountered with OVMF running on QEMU's i440fx IDE
emulation. Many thanks to John Snow for analyzing QEMU's behavior, and
pointing out that it adhered to the relevant specs.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: John Snow <jsnow@redhat.com>
Reference: https://github.com/tianocore/edk2/issues/43
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19685 6f19259b-4bc3-4df7-8a09-765794883524
The DRQReady() and DRQReady2() functions only differ in that they poll
different status registers for BSY, ERR, and DRQ: the former looks at the
Status Register (clearing interrupt status), while the latter looks at the
Alternate Status Register (not clearing interrupt status).
They both correctly return a unique status code, EFI_NOT_READY, for the
BSY==0 && ERR==0 && DRQ==0
case; that is, when the device reports "command complete".
However, the functions' leading comments don't explain this case, so it's
easy to miss in callers. Update the comments.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Cc: John Snow <jsnow@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19684 6f19259b-4bc3-4df7-8a09-765794883524
Rename the Ui libraries,so need to update the MdeModulePkg.dsc file.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19668 6f19259b-4bc3-4df7-8a09-765794883524
Avoid any confusion,add the keyword "Ui",
user can understand the use of the library clearly.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19666 6f19259b-4bc3-4df7-8a09-765794883524
Avoid any confusion,add the keyword "Ui",
user can understand the use of the library clearly.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19664 6f19259b-4bc3-4df7-8a09-765794883524
Avoid any confusion,add the keyword "Ui",
user can understand the use of the library clearly.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19662 6f19259b-4bc3-4df7-8a09-765794883524
This driver links to PciHostBridgeLib provided by platform/silicon to
produce PciRootBridgeIo and PciHostBridgeResourceAllocation protocol.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19658 6f19259b-4bc3-4df7-8a09-765794883524
PciHostBridgeDxe driver needs PciHostBridgeLib implemented by platform
to provide the root bridge related information and may call into
PciHostBridgeLib when resource conflicts happen.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19655 6f19259b-4bc3-4df7-8a09-765794883524
The MenuOption insert to gMenuOption allocate memory every time,but not free.
Now add the code to free it.And for Date/Time,it will create 3 menus,but previously
the Description point to the same address,so when free the Description,it will cause
issue,now reset the Description pointer.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19647 6f19259b-4bc3-4df7-8a09-765794883524
This patch is used to add DNS QType and QClass values definition
in NetLib.h
Cc: Hegde Nagaraj P <nagaraj-p.hegde@hpe.com>
Cc: Ye Ting <ting.ye@intel.com>
Cc: Fu Siyuan <siyuan.fu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiaxin Wu <jiaxin.wu@intel.com>
Reviewed-by: Hegde Nagaraj P <nagaraj-p.hegde@hpe.com>
Reviewed-by: Ye Ting <ting.ye@intel.com>
Reviewed-by: Fu Siyuan <siyuan.fu@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19642 6f19259b-4bc3-4df7-8a09-765794883524
When the GOP doesn't support the resolution specified by
PcdVideoHorizontalResolution and PcdVideoVerticalResolution,
the code tries to set the resolution to 800x600 but uses the resolution
equals to the PCD when calculating the text print position.
The patch fixes the bug by updating the resolution to 800x600 for
this case.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Jeff Fan <jeff.fan@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19630 6f19259b-4bc3-4df7-8a09-765794883524
When overriding compiler options '/GL' with '/GL-', VS2010 will report
warning C4701 potentially uninitialized local variable for 'LcrParity'
and 'LcrStop' in function SerialPortSetAttributes().
This commit fixes this build issue.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19628 6f19259b-4bc3-4df7-8a09-765794883524
Change EfiBootManagerDeleteLoadOptionVariable() to not just
remove #### from BootOrder but also remove Boot#### variable.
The old behavior tries to do less for performance but it leaves
unreferenced Boot#### which cannot be reclaimed in variable
reclaim operation though the Boot#### will be eventually be overwritten
by EfiBootManagerAddLoadOptionVariable().
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19626 6f19259b-4bc3-4df7-8a09-765794883524
This patch updates the MNP driver to recycle TX buffer asynchronously, instead
of using a while loop wait after each transmit command.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Fu Siyuan <siyuan.fu@intel.com>
Reviewed-by: Jiaxin Wu <jiaxin.wu@intel.com>
Reviewed-by: Ye Ting <ting.ye@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19624 6f19259b-4bc3-4df7-8a09-765794883524
This patch fixes a bug in SNP.GetStatus() interface. The UNDI driver may return
multiple transmitted buffers in a single GetStatus command, while SNP.GetStatus
could only return one pointer each time, the rest of them are lost. This patch
fixes this issue by store these recycled pointer in a temporary buffer in SNP
driver.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Fu Siyuan <siyuan.fu@intel.com>
Reviewed-by: Jiaxin Wu <jiaxin.wu@intel.com>
Reviewed-by: Ye Ting <ting.ye@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19623 6f19259b-4bc3-4df7-8a09-765794883524
As ScsiDisk and ScsiBus driver are used to manage SCSI or ATAPI devices,
the timeout value is updated to 30s to follow ATA/ATAPI spec in which
the device may take up to 30s to respond command.
The change is used to solve device compatibility issue found with a TEAC
DV-W28S-WZ3 slim DVD plus a SONY AccuCORE DVD-R media in which the DVD
spends 8s to response READ_CAPACITY cmd after resetting the host machine.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19612 6f19259b-4bc3-4df7-8a09-765794883524
When executing ATAPI cmd at IDE mode, EFI_SUCCESS may be returned wrongly
with old logic but in fact DRQ is not ready and the transaction doesn't
get executed correctly at this time.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19611 6f19259b-4bc3-4df7-8a09-765794883524
The MenuOption insert to gMenuOption allocate memory everytime,but not free.
Now add the code to free it.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19593 6f19259b-4bc3-4df7-8a09-765794883524
Currently the invalid boot next set to the number of boot option,
when add a new boot option,also need update the boot next value,
otherwise it will be incorrect.Now set the type of BootNext value
to UINT32,the number out of the range of UINT16 means it is an
invalid BootNext Value.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19591 6f19259b-4bc3-4df7-8a09-765794883524
Add error handling code to enhance the code,the driver may not install
the ConfigAccess protocol,so should not just ASSERT here.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19590 6f19259b-4bc3-4df7-8a09-765794883524
Variable driver uses gEdkiiFaultTolerantWriteGuid hob and copies data to NvStorageData if hob exists.
But if ftw driver executes prior to variable driver then spare block is erased.
So the patch is to enhance the code to do not check FTW last write data hob if FTW protocol has been installed.
Cc: Liming Gao <liming.gao@intel.com>
Reported-by: Baraneedharan Anbazhagan <anbazhagan@hp.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Baraneedharan Anbazhagan <anbazhagan@hp.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19577 6f19259b-4bc3-4df7-8a09-765794883524
The code wrongly has TempFlag wrote to NV flash, but has Flag assigned to NV cache.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19573 6f19259b-4bc3-4df7-8a09-765794883524
HwErrVariableTotalSize/CommonVariableTotalSize/CommonUserVariableTotalSize
need to be initialized to 0 first after reclaim failed, then to be assigned by += operation.
Cc: Liming Gao <liming.gao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19572 6f19259b-4bc3-4df7-8a09-765794883524
White space clean up for MdeModulePkg.dec
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Daocheng Bu <daocheng.bu@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19486 6f19259b-4bc3-4df7-8a09-765794883524
Add IpmiLib and Ppi/Protocol header file. Update dec file
for new IpmiLib and Ppi/Protocol header file.
In V5,change for coding style.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Daocheng Bu <daocheng.bu@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19485 6f19259b-4bc3-4df7-8a09-765794883524
This commit will raise the Tpl to TPL_NOTIFY when adding non-blocking SCSI
I/O requests to the asynchronous task list.
This commit will also raise the Tpl of asynchronous task polling timer to
TPL_NOTIFY.
These changes are made to match the behavior in ScsiDiskDxe driver.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19455 6f19259b-4bc3-4df7-8a09-765794883524
Raise the Tpl of async SCSI I/O callback function to TPL_NOTIFY to match
the behavior in ScsiDiskDxe driver.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19454 6f19259b-4bc3-4df7-8a09-765794883524
When reading data from non-blockingly from a CD-ROM logic partition, the
procedure can be shown by the following call stack:
(The write process is similar)
|-------------------|
| DiskIoDxe (logic) |<---Raise Tpl to TPL_CALLBACK
|-------------------|
|
| Sub-task 1 (UnderRun) succeeds
|
| |-----------------| |-----------------| |-----------------|
+--->| PartitionDxe |---->| DiskIoDxe (Phy) |---->| ScsiDiskDxe |
| |-----------------| |-----------------| |-----------------|
|
| Sub-task 2 (OverRun) fails
|
| |-----------------| |-----------------| |-----------------|
+--->| PartitionDxe |---->| DiskIoDxe (Phy) |---->| ScsiDiskDxe |
| |-----------------| |-----------------| |-----------------|
| ^
| |
More subtasks... Wait indefinitely
|
|<---Restore Tpl
|
Completes
In PartitionDxe, if the 'Lba' and 'BufferSize' parameters passed to
function PartitionReadBlocksEx() are invalid, the function will issue a
blocking ReadDisk call (in function ProbeMediaStatusEx()).
In DiskIoDxe, blocking I/O request will wait for all the non-blocking I/O
requests to complete first before sending down the blocking request.
If the Tpl of the async I/O callback in ScsiDiskDxe is TPL_CALLBACK and
Sub-task 1 (UnderRun) succeeds but Sub-task 2 (OverRun) fails with an
invalid parameter, DiskIoDxe will wait indefinitely for the event created
by ScsiDiskDxe of Sub-task 1 to signal.
Hence, this commit will raise the Tpl of async IO callback in ScsiDiskDxe
to TPL_NOTIFY so that the indefinite wait in DiskIoDxe can be avoided.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19452 6f19259b-4bc3-4df7-8a09-765794883524
Some SCSI devices will return EFI_DEVICE_ERROR or EFI_TIMEOUT when the
data length of a SCSI I/O command is too large.
This commit will repeatedly retry sending the SCSI command with a data
length half of its previous value.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19451 6f19259b-4bc3-4df7-8a09-765794883524
The functions ScsiRead10CommandEx(), ScsiWrite10CommandEx(),
ScsiRead16CommandEx() and ScsiWrite16CommandEx() in UefiScsiLib will not
signal the event passed from ScsiDiskDxe when error occurs.
In this case, ScsiDiskDxe should close the event passing to these APIs in
UefiScsiLib.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19449 6f19259b-4bc3-4df7-8a09-765794883524
In ScsiExecuteSCSICommand(), when SCSI devices do not support non-blocking
I/O but an event is passed from caller (UefiScsiLib), the function will
execute the SCSI I/O command in a blocking manner and signal the caller
event when the command completes.
Originally, caller event from UefiScsiLib will be signaled if the SCSI
command fails. UefiScsiLib will continue to signal its caller (BlockIO2
request from ScsiDiskDxe driver), which is not aligned with the UEFI spec
that event will not be signaled when BlockIO2 request returns with error.
This commit will signal ScsiExecuteSCSICommand()'s caller event only when
the SCSI command succeeds.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19447 6f19259b-4bc3-4df7-8a09-765794883524
Add check to see if there is a media in the disk device. If not return
EFI_NO_MEDIA directly.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19446 6f19259b-4bc3-4df7-8a09-765794883524
The functions ScsiDiskWriteBlocks(Ex) in ScsiDiskDxe/ScsiDisk.c do not
check whether the device is allow to be written originally.
This commit will add read-only check to follow the UEFI spec.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19445 6f19259b-4bc3-4df7-8a09-765794883524
The function ScsiDiskFlushBlocksEx() in ScsiDiskDxe/ScsiDisk.c originally
always returns EFI_SUCCESS, which is not aligned with the UEFI spec.
This commit adds addtional checks to see if the media in the device is
changed or removed. Check for whether the device can be written is also
added. Corresponding status will be returned according to the check
result.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19444 6f19259b-4bc3-4df7-8a09-765794883524
When do UiApp remodeling task,miss clearing the screen before booting
the selected boot option,so cause some behaviors change.Now add the code
to fix this issue.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19441 6f19259b-4bc3-4df7-8a09-765794883524
Currently BootManager is an independent library,used by UiApp.It only load boot
option when enter UiApp.So when add boot option through boot maintenance manager,
it will not display in boot manager. In order to fix this issue,now we update the
boot manager form every time we enter it.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19440 6f19259b-4bc3-4df7-8a09-765794883524
The single line for(); construct is followed by code that is indented.
This triggers the -Wempty-body warning. Fix indentation.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Andrew Fish <afish@apple.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19420 6f19259b-4bc3-4df7-8a09-765794883524
Xcode fails to compile:
error: array type 'VA_LIST' (aka '__builtin_va_list') is not assignable
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Andrew Fish <afish@apple.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19419 6f19259b-4bc3-4df7-8a09-765794883524
Add clarification for PcdAcpiDefaultOemTableId, PcdAcpiDefaultOemRevision,
PcdAcpiDefaultCreatorId, PcdAcpiDefaultCreatorRevision.
According to ACPI spec, they are used as special meaning for SSDT,
so we ignore them in updating generic SSDT provided by EDKII.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: "Yao, Jiewen" <jiewen.yao@intel.com>
Reviewed-by: "Zeng, Star" <star.zeng@intel.com>com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19321 6f19259b-4bc3-4df7-8a09-765794883524
In DxeCore, use warning message for Runtime driver that doesn't satisfy
section alignment requirement. This check is required when PropertiesTable
is installed. So, add error message if PropertiesTable can't be installed
successfully.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19312 6f19259b-4bc3-4df7-8a09-765794883524
When HttpLib parsing the last chunked data down, the Http NextMsg pointer
in the HttpBodyParserCallback function should point to the character
after '/n' flag.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Zhang Lubo <lubo.zhang@intel.com>
Reviewed-by: Fu Siyuan <siyuan.fu@intel.com>
Reviewed-by: Ye Ting <ting.ye@intel.com>
Reviewed-by: Wu Jiaxin <jiaxin.wu@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19310 6f19259b-4bc3-4df7-8a09-765794883524
Operands in a bitwise operation have different size. Update code to fix it.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Qiu Shumin <shumin.qiu@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19309 6f19259b-4bc3-4df7-8a09-765794883524
The caller has initial the input parameter before call this function, So this code is useless.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19302 6f19259b-4bc3-4df7-8a09-765794883524
On a failed REF_OP callback, all changed fields in the Selection should be restored.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Cecil Sheng <cecil.sheng@hpe.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Samer El-Haj-Mahmoud <elhaj@hpe.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19268 6f19259b-4bc3-4df7-8a09-765794883524
In function SignalCallerEvent(), 'Private' and 'TransReq' are dereferenced
before NULL checking.
Since the function assumes that both 'Private' and 'TransReq' passed in
are not NULL pointer, this commit will add an ASSERT to make sure the
above assumption is satisfied.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19266 6f19259b-4bc3-4df7-8a09-765794883524
On a failed REF_OP callback, all changed fields in the Selection should be restored.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Cecil Sheng <cecil.sheng@hpe.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Samer El-Haj-Mahmoud <elhaj@hpe.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19245 6f19259b-4bc3-4df7-8a09-765794883524
Add missing braces in module global mControllerDevicePathTemplate.
Initialize ControllerNumber and ContainsControllerNode in
SerialControllerDriverStart() to address warning for potential use
before initialization warning.
Move initialization of local SerialIo earlier in
SerialControllerDriverStart() to address warning for potential use
before initialization warning.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Michael Kinney <michael.d.kinney@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19232 6f19259b-4bc3-4df7-8a09-765794883524
This should just return an error and not assert. We hit this when testing with a client that was trying to access the old IP4_CONFIG on firmware implementing IP4_CONFIG2.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Eugene Cohen <eugene@hp.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19219 6f19259b-4bc3-4df7-8a09-765794883524
For function ScsiExecuteSCSICommand(), when the 'Event' parameter is not
NULL but the target SCSI device does not support non-blocking I/O, it will
execute a blocking I/O operation instead.
However, after the SCSI operation is done, the 'Event' is not signaled to
inform the caller.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19217 6f19259b-4bc3-4df7-8a09-765794883524
PciSioSerialDxe driver can manages UARTs on a SIO chip or a PCI/PCIE
card.
It manages the SIO instance whose last device path node is a ACPI
device path and the HID in the ACPI device path node equals to
EISA_PNP_ID (0x501).
It also manages the PCI IO instance whose class code is 7/0/2 (16550
UART). But when proper value is set to PcdPciSerialParameters, the
driver can also manage non-standard PCI serial cards by matching
the Vendor ID and Device ID specified in PcdPciSerialParameters.
The PCI BAR index, IO/MMIO offset, register stride, clock rate can
also be specified through the same PCD.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19179 6f19259b-4bc3-4df7-8a09-765794883524
DeployedMode & AuditMode are UINT8 Global variable according to Enable Secure Boot feature defined in UEFI2.5 Mantis 1263. Add them to var check list.
https://mantis.uefi.org/mantis/view.php?id=1263
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Chao Zhang <chao.b.zhang@intel.com>
Reviewed-by: Zeng Star <star.zeng@intel.com>
Reviewed-by: Long Qin <qin.long@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19131 6f19259b-4bc3-4df7-8a09-765794883524
If the assert happens in a library, then it's hard to determine which module
using that library is generating that assert. Use gEfiCallerBaseName in
DebugAssert to display the module name.
V2: Updated code to use copy mem and ModuleNameSize calculation.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Baraneedharan Anbazhagan <anbazhagan@hp.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19128 6f19259b-4bc3-4df7-8a09-765794883524
warning C4311: pointer truncation from 'void *' to 'unsigned long'
warning C4312: conversion from 'unsigned long' to 'void *' of greater size
Update code to convert type to UINTN first, then convert it to other type.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Samer El-Haj-Mahmoud <samer.el-haj-mahmoud@hpe.com>
Acked-by: Michael Kinney <michael.d.kinney@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19114 6f19259b-4bc3-4df7-8a09-765794883524
warning C4456: declaration of 'q' hides previous local declaration.
Update code to use the different local variable name.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Samer El-Haj-Mahmoud <samer.el-haj-mahmoud@hpe.com>
Acked-by: Michael Kinney <michael.d.kinney@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19113 6f19259b-4bc3-4df7-8a09-765794883524
warning C4459: declaration of 'PrivateData' hides global declaration.
Update DriverSampleDxe to rename global variable name to be different.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19112 6f19259b-4bc3-4df7-8a09-765794883524
BDS puts a special GUID in boot option optional data for
auto-discovered boot option. But when launching that boot
option, the BDS core unconditionally pass the special GUID
to the executable.
A good written application/OS loader can ignore the unexpected
parameters, but BDS core should still avoid passing the
unnecessary GUID.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@19007 6f19259b-4bc3-4df7-8a09-765794883524
Add comments in INF file in BootMaintenanceManagerLib.inf.
Refine the comments in INF file in FileExplorerLib.inf
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18975 6f19259b-4bc3-4df7-8a09-765794883524
This Serial driver layers on top of a Serial Port Library instance
to produce serial IO protocol.
There is also another SerialDxe implementation in CorebootPayloadPkg,
but SerialDxe from EmbeddedPkg should be better that also consumes
the extended interfaces GetControl/SetControl/SetAttributes in
EmbeddedPkg/Include/Library/SerialPortExtLib.h for serial IO protocol.
And the extended interfaces GetControl/SetControl/SetAttributes in
EmbeddedPkg/Include/Library/SerialPortExtLib.h has been upstream to
MdePkg/Include/Library/SerialPortLib.h.
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18966 6f19259b-4bc3-4df7-8a09-765794883524
The SerialIo->GetControl() function is not required to set the
Control output parameter on error. Make sure we apply the
EFI_SERIAL_INPUT_BUFFER_EMPTY optimization in
TerminalConInTimerHandler() only if the SerialIo->GetControl()
function call set that bit in the Control variable.
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Suggested-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18962 6f19259b-4bc3-4df7-8a09-765794883524
We had put communication buffer to Runtime memory,
so that SMI handler can know it is not used by OS.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: "Yao, Jiewen" <jiewen.yao@intel.com>
Reviewed-by: "Zeng, Star" <star.zeng@intel.com>
Reviewed-by: "Kinney, Michael D" <michael.d.kinney@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18949 6f19259b-4bc3-4df7-8a09-765794883524
PiSmmCore installs LoadedImage for each SMM driver. However itself is missing.
So we follow DxeCore style, let PiSmmCore installs LoadedImage protocol for itself,
then the SMM image information is complete.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: "Yao, Jiewen" <jiewen.yao@intel.com>
Reviewed-by: "Zeng, Star" <star.zeng@intel.com>
Reviewed-by: "Kinney, Michael D" <michael.d.kinney@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18945 6f19259b-4bc3-4df7-8a09-765794883524
Original code does not uninstall LoadedImage protocol if SMM driver returns error and is unloaded.
It causes a wrong LoadedImage protocol existing in system.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: "Yao, Jiewen" <jiewen.yao@intel.com>
Reviewed-by: "Zeng, Star" <star.zeng@intel.com>
Reviewed-by: "Kinney, Michael D" <michael.d.kinney@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18936 6f19259b-4bc3-4df7-8a09-765794883524
Original code refers FreePoolHdr without check Status. It is obvious wrong and has risk.
Aslo, if InternalAllocPoolByIndex() returns an error, then *FreePoolHdr is assigned to an uninitialized value. So we init Hdr be NULL.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: "Zeng, Star" <star.zeng@intel.com>
Reviewed-by: "Yao, Jiewen" <jiewen.yao@intel.com>
Reviewed-by: "Fan, Jeff" <jeff.fan@intel.com>
Reviewed-by: "Kinney, Michael D" <michael.d.kinney@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18932 6f19259b-4bc3-4df7-8a09-765794883524
Align to old BDS behavior (IntelFrameworkModulePkg/BDS) to always create
MemoryTypeInfo variable regardless of the PcdResetOnMemoryTypeInformationChange
value.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Michael Kinney <michael.d.kinney@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18926 6f19259b-4bc3-4df7-8a09-765794883524
Use new created libraries(Boot Manager,Device Manager,Boot Maintenance
Manager) in UiApp.So remove and refine relative code in UiApp.And update
the Nt32Pkg.dsc and MdeModulePkg.dsc.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18924 6f19259b-4bc3-4df7-8a09-765794883524
Split the boot maintenance manager library from UiApp in MdeModulePkg/Application
and put the library in MdeModulePkg/Library.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18923 6f19259b-4bc3-4df7-8a09-765794883524
Split the device manager library from UiApp in MdeModulePkg/Application
and put the library in MdeModulePkg/Library.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18922 6f19259b-4bc3-4df7-8a09-765794883524
Split the boot manager library from UiApp in MdeModulePkg/Application
and put the library in MdeModulePkg/Library.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18921 6f19259b-4bc3-4df7-8a09-765794883524
This library wrapper explorer protocol and produce the file explorer library.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Samer El-Haj-Mahmoud <elhaj@hpe.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18919 6f19259b-4bc3-4df7-8a09-765794883524
This driver produces file explorer protocol layered on top of the FileExplorerLib.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Samer El-Haj-Mahmoud <elhaj@hpe.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18918 6f19259b-4bc3-4df7-8a09-765794883524
This library support select one file from the specified directory or from system root directory.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Samer El-Haj-Mahmoud <elhaj@hpe.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18917 6f19259b-4bc3-4df7-8a09-765794883524
The "read" word in SerialPortWrite() header comment block should be
"write".
Cc: Michael D Kinney <michael.d.kinney@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Michael D Kinney <michael.d.kinney@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18910 6f19259b-4bc3-4df7-8a09-765794883524
The ASSERT (PrivateData->PeiMemoryInstalled) in if (PrivateData->PeiMemoryInstalled)
condition is useless, it should be ASSERT (FALSE) to follow the code's expectation.
Cc: Liming Gao <liming.gao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18887 6f19259b-4bc3-4df7-8a09-765794883524
The parameter name is also changed from Coordinate* to Offset* to
reflect that it's the offset to the location specified by Attribute.
For example, when the Attribute is Center, OffsetX and OffsetY are
used to specify the offset to the Center. OffsetX = 100 means
100 pixels right to the Center.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18867 6f19259b-4bc3-4df7-8a09-765794883524
The parameter name is also changed from Coordinate* to Offset* to
reflect that it's the offset to the location specified by Attribute.
For example, when the Attribute is Center, OffsetX and OffsetY are
used to specify the offset to the Center. OffsetX = 100 means
100 pixels right to the Center.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18866 6f19259b-4bc3-4df7-8a09-765794883524
The patch also moves the BmCharToUint to BmMisc.c because it
belongs to misc functions.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Sunny Wang <sunnywang@hpe.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18855 6f19259b-4bc3-4df7-8a09-765794883524
The RestoreLockBox() and RestoreAllLockBoxInPlace() functions handle the
case when EFI_PEI_SMM_COMMUNICATION_PPI.Communicate() returns
EFI_NOT_STARTED: they access the SMRAM directly, for restoring LockBox
data.
This occurs if a PEIM needs to restore LockBox data *before* the SMBASE is
relocated and the SMI handler is installed for all processors.
One such PEIM is UefiCpuPkg/Universal/Acpi/S3Resume2Pei. On the S3 resume
path, in function S3RestoreConfig2(), LockBox data are restored *before*
the SmmRestoreCpu() function of UefiCpuPkg/PiSmmCpuDxeSmm is called via
SmmS3ResumeState->SmmS3ResumeEntryPoint. (The latter SmmRestoreCpu()
function is responsible for the SMBASE relocation.)
If a platform knows that its PEIMs restore LockBox data *only* before
SMBASE relocation -- e.g., due to S3Resume2Pei being the platform's only
SmmLockBoxPeiLib client --, then the platform might not want to include
"UefiCpuPkg/PiSmmCommunication/PiSmmCommunicationPei.inf" at all (hence
not provide EFI_PEI_SMM_COMMUNICATION_PPI) -- because all of those
restores would be serviced by direct SMRAM access anyway.
Currently the absence of EFI_PEI_SMM_COMMUNICATION_PPI is not supported by
SmmLockBoxPeiLib, but it's not hard to implement. Handle it the same as
when EFI_PEI_SMM_COMMUNICATION_PPI.Communicate() returns EFI_NOT_STARTED:
restore LockBox data directly from SMRAM.
Suggested-by: Jiewen Yao <jiewen.yao@intel.com>
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Michael Kinney <michael.d.kinney@intel.com>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18823 6f19259b-4bc3-4df7-8a09-765794883524
A corner case like below will cause a NOT_DISPATCHED FV has no opportunity to
be dispatched.
1. FV_RECOVERY has SecCore, PeiCore and some other PEI modules, a module will
report FVMAIN_COMPACT and FV_RECOVERY2 in sequence.
2. FVMAIN_COMPACT has a FV image file with GUIDED FV image section in it.
3. FV_RECOVERY2 has DxeIpl and other PEI modules, the DxeIpl will install
SectionExtractionPpi
If ALL the PEIMs in FV_RECOVERY and FV_RECOVERY2 have DEPEX satisfied and
executed in one loop, PeimNeedingDispatch will be always FALSE, FVMAIN_COMPACT
will have no opportunity to be decompressed and dispatched as DxeIpl executes
after the first processing to FVMAIN_COMPACT.
The patch is to set PeimNeedingDispatch to TRUE when ProcessFvFile() not successfully,
then the NOT_DISPATCHED FV could have another opportunity to be processed.
Cc: Liming Gao <liming.gao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Eugene Cohen <eugene@hp.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18781 6f19259b-4bc3-4df7-8a09-765794883524
The library itself doesn't provide any image decoding capabilities but
manages the different image decoders.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18770 6f19259b-4bc3-4df7-8a09-765794883524
Previously the pointer type is EFI_IFR_FORM_SET, it is incorrect when
do pointer addition without conversion.Now change it to UINT8 type.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18768 6f19259b-4bc3-4df7-8a09-765794883524
This patch fixes an issue in PEI with encapsulated FV images where the
AuthenticationStatus is not correctly propagated down to child FV
handles. The PEI core registers for callbacks for both FvInfo and
FvInfo2 PPIs. These callbacks process the FVs which will recurse as
necessary to find more encapsulated FVs. (FvInfo2 is an updated PPI
that includes an AuthenticationStatus field - the original FvInfo did
not include this.)
When encapsulated FV processing occurs the PEI core installs both
FvInfo and FvInfo2 PPIs. The original implementation installs FvInfo
first and FvInfo2 second. As soon as the FvInfo PPI is installed the
notification callback handler immediately fires causing recursive FV
processing to occur. Since there is no AuthenticationStatus provided
for the original FvInfo the callback assumes AuthenticationStatus is
zero (unsigned / unverified) even though the parent FV may have been
verified.
This changes the order of FvInfo and FvInfo2 installs to ensure that
the notification callback occurs for FvInfo2 first and appropriate
AuthenticationStatus data can be propagated from parent FV to child
FV.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Eugene Cohen <eugene@hp.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18764 6f19259b-4bc3-4df7-8a09-765794883524
When parsing the authority component of the input URL, it can not distinguish
the ":" is the flag that indicates the port or the separator between
the ipv6 address.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Zhang Lubo <lubo.zhang@intel.com>
Reviewed-by: Fu Siyuan <siyuan.fu@intel.com>
Reviewed-by: Wu Jiaxin <jiaxin.wu@intel.com>
Reviewed-by: Gary Ching-Pang Lin <glin@suse.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18744 6f19259b-4bc3-4df7-8a09-765794883524
AsciiVSPrint is used in RegularExpressionDxe/Oniguruma/OnigurumaUefiPort.c.
But PrintLib is missing in RegularExpressionDxe.inf.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Cinnamon Shia <cinnamon.shia@hpe.com>
Reviewed-by: Samer El-Haj-Mahmoud <elhaj@hpe.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18721 6f19259b-4bc3-4df7-8a09-765794883524
For a hot plug bridge with device attached, PciBusDxe driver reserves
the resources which equal to the total amount of padding resource
returned from HotPlug->GetResourcePadding() and the actual occupied
resource by the attached device. The behavior is incorrect.
Correct behavior is to reserve the bigger one between the padding
resource and the actual occupied resource.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18719 6f19259b-4bc3-4df7-8a09-765794883524
The resource dumping logic contains a bug which cannot dump the
resource for hot plug controller correctly. The patch fixes this
bug.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18718 6f19259b-4bc3-4df7-8a09-765794883524
Leif suggested to split the big patch to smaller ones.
This reverts commit 73b7f115c653c807b9d0be97bf516871d8aff7ba.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18717 6f19259b-4bc3-4df7-8a09-765794883524
A subset of fields in the EFI_SMM_SYSTEM_TABLE2 structure are identical
to the fields in the SMM_ENTRY_CONTEXT structure. CopyMem() is used to
transfer the contents of the SMM_ENTRY_CONTEXT structure into the
EFI_SMM_SYSTEM_TABLE2. This is confusing because SMM_ENTRY_CONTEXT is
not used in the declaration of EFI_SMM_SYSTEM_TABLE2 and field contents
are transferred without any reference to individual field names (e.g.
CurrentlyExecutingCpu). In order to make the code easier to maintain
and understand, the CopyMem() is replaced with statements that transfer
each field of SMM_ENTRY_CONTEXT into EFI_SMM_SYSTEM_TABLE2.
Reported-by: Laszlo Ersek <lersek@redhat.com>
Link: http://article.gmane.org/gmane.comp.bios.edk2.devel/3567
Cc: Feng Tian <feng.tian@intel.com>
Cc: Jeff Fan <jeff.fan@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Michael Kinney <michael.d.kinney@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18716 6f19259b-4bc3-4df7-8a09-765794883524
Add a DEBUG statement when the number of PEI perf log entries
exceeds PcdMaxPeiPerformanceLogEntries
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Samer El-Haj-Mahmoud <samer.el-haj-mahmoud@hpe.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18714 6f19259b-4bc3-4df7-8a09-765794883524
When StringId is not 0, String returned from GetSmbiosStringById is expected to non-NULL.
Add ASSERT (String != NULL); to ensure this.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Shumin Qiu <shumin.qiu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Shumin Qiu <shumin.qiu@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18713 6f19259b-4bc3-4df7-8a09-765794883524
Add a check for ResourcePaddingDescriptors being a valid pointer in
DumpPpbPaddingResource() to prevent looping on memory not owned by
PciBusDxe. The ResourcePaddingDescriptors is initialized to NULL
when the PCI_IO_DEVICE structure is allocated and remains NULL if
no PCI hot plug controllers are present. This issue is only
observed when DEBUG_CODE() macros are enabled and was introduced
by the following patch:
[edk2] [Patch] MdeModulePkg: Fix a PciBusDxe hot plug bug
SVN revsion 18658
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Kinney Michael <michael.d.kinney@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18696 6f19259b-4bc3-4df7-8a09-765794883524
1. Correct the return comments of entrypoint function.
2. Add parameters' comments for MeasureSmbiosTable().
3. Correct the Protocols and Guids usage comments in SmbiosMeasurementDxe.inf.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18695 6f19259b-4bc3-4df7-8a09-765794883524
Use EFI_D_VERBOSE instead of EFI_D_INFO in InternalDumpData() and InternalDumpHex().
And also add DEBUG_CODE wrapper to InternalDumpHex() call.
It is to avoid the bother from the internal verbose debug information.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18693 6f19259b-4bc3-4df7-8a09-765794883524
1. Smbios3Table used as SmbiosTable wrongly after SmbiosTable got from configuration table.
2. Use correct VendorGuid and VendorTable to measure.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18691 6f19259b-4bc3-4df7-8a09-765794883524
This change is triggered by R18654 "Enhance variable performance by reading from existed memory cache"
that changed the code to use CacheVariable to improve performance.
So the CacheVariable->InDeletedTransitionPtr NULL pointer check needs to be moved to the place before
it is been used.
Cc: Shumin Qiu <shumin.qiu@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Shumin Qiu <shumin.qiu@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18688 6f19259b-4bc3-4df7-8a09-765794883524
This function is mainly through the Hii handle to get the formset opcode.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18684 6f19259b-4bc3-4df7-8a09-765794883524
The SendForm function can be called nest in it. This function also uses some global variables. So we must save global variable values before it been called again.
Checked in the missing change for gBrowserFormSetList.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18681 6f19259b-4bc3-4df7-8a09-765794883524
This is patch to add smbios measurement.
The problem of current SMBIOS measurement is:
1) TCG drivers do not support SMBIOS3.0 table.
2) TCG drivers do not follow TCG platform spec on: "Platform configuration information that is automatically updated,
such as clock registers, and system unique information, such as asset numbers or serial numbers,
MUST NOT be measured into PCR [1], or any other PCR."
So we decide to move Smbios measurement from TCG drivers to Smbios driver.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: "Yao, Jiewen" <jiewen.yao@intel.com>
Reviewed-by: "Zeng, Star" <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18680 6f19259b-4bc3-4df7-8a09-765794883524
So that other module can also refer to them.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: "Yao, Jiewen" <jiewen.yao@intel.com>
Reviewed-by: "Zeng, Star" <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18674 6f19259b-4bc3-4df7-8a09-765794883524
Make the BmFindLoadOption function public
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Sunny Wang <sunnywang@hpe.com>
Reviewed-by: Samer El-Haj-Mahmoud <elhaj@hpe.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18662 6f19259b-4bc3-4df7-8a09-765794883524
For a hot plug bridge with device attached, PciBusDxe driver reserves
the resources which equal to the total amount of padding resource
returned from HotPlug->GetResourcePadding() and the actual occupied
resource by the attached device. The behavior is incorrect.
Correct behavior is to reserve the bigger one between the padding
resource and the actual occupied resource.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18658 6f19259b-4bc3-4df7-8a09-765794883524
Current variable driver already have memory cache to improve performance.
Change the code which read from physical MMIO address to read from memory cache.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Derek Lin <derek.lin2@hpe.com>
Reviewed-by: Samer El-Haj-Mahmoud <elhaj@hpe.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18654 6f19259b-4bc3-4df7-8a09-765794883524
The SendForm function can be called nest in it. This function also uses some global variables. So we must save global variable values before it been called again.
Old implementation miss to save some global variables, this patch fixed it.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18650 6f19259b-4bc3-4df7-8a09-765794883524
R18611 only updated the logic to return correct property
when no property set to variable with wildcard name.
But VariablePropertySet needs the pointer of property data for set.
So roll back the change in VariablePropertyGetWithWildcardName at R18611,
and check the property revision first in VariablePropertyGet and
SetVariableCheck before using the property data.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18626 6f19259b-4bc3-4df7-8a09-765794883524
These messages don't report errors, hence they should be emitted as
EFI_D_INFO (or EFI_D_VERBOSE even).
Cc: Star Zeng <star.zeng@intel.com>
Cc: Drew Jones <drjones@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18621 6f19259b-4bc3-4df7-8a09-765794883524
The "success" messages in FtwRestart(), FtwAbort(), and FtwGetLastWrite()
should be logged on EFI_D_INFO level. We can also unify their format with
the __FUNCTION__ macro.
Cc: Star Zeng <star.zeng@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Cc: Drew Jones <drjones@redhat.com>
Suggested-by: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18620 6f19259b-4bc3-4df7-8a09-765794883524
The IsValidWorkSpace() function checks if the working block header of the
workspace is valid. A mismatch detected by this function is not
necessarily an error; it can happen with an as-yet unwritten flash chip,
which is e.g. common and normal when a new ArmVirtQemu virtual machine is
booted. Therefore downgrade the message emitted by IsValidWorkSpace() from
EFI_D_ERROR to EFI_D_INFO, and change the wording from "error" to
"mismatch".
The only caller of IsValidWorkSpace(), InitFtwProtocol(), handles all of
the following cases:
(1) IsValidWorkSpace() succeeds for the working block -- this is normal
operation,
(2) IsValidWorkSpace() fails for the working block, but succeeds for the
spare block -- InitFtwProtocol() then restores the working block from
the spare block,
(3) IsValidWorkSpace() fails for both the working and spare blocks --
InitFtwProtocol() reinitializes the full workspace.
In cases (2) and (3), InitFtwProtocol() logs additional messages about the
branch taken. Their current level is EFI_D_ERROR, but the messages are
arguably informative, not necessarily error reports.
Downgrade these messages from EFI_D_ERROR to EFI_D_INFO, so that they
don't clutter the debug output when the PcdDebugPrintErrorLevel mask only
enables EFI_D_ERROR (i.e., in a "silent" build).
These messages have annoyed / confused users; see for example:
- https://bugzilla.redhat.com/show_bug.cgi?id=1270279
Cc: Star Zeng <star.zeng@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Cc: Drew Jones <drjones@redhat.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18619 6f19259b-4bc3-4df7-8a09-765794883524
The DHCP4 can have only one configured child instance so we need to reset
the DHCP4 child when leaving PXE driver's LoadFile() function, otherwise the
other programs which also need to use DHCP4 (like HTTP boot) will be impacted.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Fu Siyuan <siyuan.fu@intel.com>
Reviewed-by: Sriram Subramanian <sriram-s@hpe.com>
Reviewed-by: Ye Ting <ting.ye@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18615 6f19259b-4bc3-4df7-8a09-765794883524
Otherwise there will be build failure if without VarCheckUefiLib linked.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18612 6f19259b-4bc3-4df7-8a09-765794883524
to variable with wildcard name.
VarCheckLib has zeroed property for variable with wildcard name
and is waiting for property set. The code should return NULL
when no property set to variable with wildcard name, but not
return the zeroed property that will impact the functionality of
SetVariableCheck.
The issue does not appear with VarCheckUefiLib linked as the library
just has the expected property set.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18611 6f19259b-4bc3-4df7-8a09-765794883524
Refine the sample code, add extra ";" to keep consistent for the condition opcode in different use cases.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18607 6f19259b-4bc3-4df7-8a09-765794883524
In current case, if one key was requested to register twice, browser will override old hot key with new one. This behavior is not user friendly.
Now update the logic, return EFI_ALREADY_STARTED for this case. If user still want to override it, he must unregistered it first.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18604 6f19259b-4bc3-4df7-8a09-765794883524
PcdSet## has no error status returned, then the caller has no idea about whether the set operation is successful or not.
PcdSet##S were added to return error status and PcdSet## APIs were put in ifndef DISABLE_NEW_DEPRECATED_INTERFACES condition.
To adopt PcdSet##S and further code development with DISABLE_NEW_DEPRECATED_INTERFACES defined, we need to Replace PcdSet## usage with PcdSet##S.
Normally, DynamicDefault PCD set is expected to be success, but DynamicHii PCD set failure is a legal case.
So for DynamicDefault, we add assert when set failure. For DynamicHii, we add logic to handle it.
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18603 6f19259b-4bc3-4df7-8a09-765794883524
PcdSet## has no error status returned, then the caller has no idea about whether the set operation is successful or not.
PcdSet##S were added to return error status and PcdSet## APIs were put in ifndef DISABLE_NEW_DEPRECATED_INTERFACES condition.
To adopt PcdSet##S and further code development with DISABLE_NEW_DEPRECATED_INTERFACES defined, we need to Replace PcdSet## usage with PcdSet##S.
Normally, DynamicDefault PCD set is expected to be success, but DynamicHii PCD set failure is a legal case.
For this case, PcdS3BootScriptTablePrivateDataPtr and PcdS3BootScriptTablePrivateSmmDataPtr are expected to be DynamicDefault,
so use PcdSet64S to instead of PcdSet64 and assert when set failure.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18599 6f19259b-4bc3-4df7-8a09-765794883524
Mark the DXE stack region as non-executable right before handing
off to the DXE core, by invoking the appropriate ArmLib function.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Reviewed-by: Feng Tian <Feng.Tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18588 6f19259b-4bc3-4df7-8a09-765794883524
When looping through all PCI functions, code should not look for functions
1-7 if function 0 is not present or if function 0 indicates the device is
not multifunction. Prior to this fix the code would use stale data in a
buffer to determine if a device is multifunction even if function 0 is not
present. This fixes a code bug and provides very small performance
improvements.
PCI 2.3 Specification states: They [multifunction devices] are also
required to always implement function 0 in the device. Implementing other
functions is optional and may be assigned in any order.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Joseph Shifflett <joseph.shifflett@hpe.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18574 6f19259b-4bc3-4df7-8a09-765794883524
Current implementation assumes the performance entry count has no change from
multiple GetPerformanceMeasurement() while loops, it may cause the allocated buffer
for PerfEntriesAsDxeHandle at the first loop to be overflowed if the following loop has
the count changed.
This patch is also to sync the change at
commit R17851 "IntelFrameworkModulePkg GenericBdsLib: Resolve array size mismatch".
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18561 6f19259b-4bc3-4df7-8a09-765794883524
Ip4Config2 protocol implementation must request for DNS server info when the
policy is set to DHCP. And when a DHCP server responds to it with a list of
DNS server addresses, it must parse it and set it for the instance. Without
this, nobody can do a Ip4Config->GetData for DNS server IPs before calling
Dns->Configure(). This will mean a DHCP is initiated when calling
Dns->Configure(), thus causing serious performance issues. This patch
attempts to address this issue.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Samer El-Haj-Mahmoud <samer.el-haj-mahmoud@hpe.com>
Reviewed-by: Ye Ting <ting.ye@intel.com>
Reviewed-by: Samer El-Haj-Mahmoud <elhaj@hpe.com>
Reviewed-by: Fu Siyuan <siyuan.fu@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18560 6f19259b-4bc3-4df7-8a09-765794883524
NetLibGetSystemGuid gets the UUID from SMBIOS table to use as the System GUID
(in DHCP and other network use cases). This change adds support to get the
UUID from either SMBIOS 2.x or 3.0, since SMBIOS 3.0 uses a different GUID in
the System Configuration Table.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Samer El-Haj-Mahmoud <samer.el-haj-mahmoud@hpe.com>
Reviewed-by: Fu Siyuan <siyuan.fu@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18559 6f19259b-4bc3-4df7-8a09-765794883524
Some IDE controllers only update ID fields such as sector information on
specific commands such as the DIAG command.
The master/slave device is therefore selected both before and after
sending the DIAG command; otherwise reading the IDE registers yields the
master's ID fields.
(Reza's patch originally *moved* the master/slave selection from after the
DIAG command before it, however Feng asked for the original master/slave
select to be preserved; effectively making the master/slave select
*bracket* the DIAG command. See this subthread:
<http://thread.gmane.org/gmane.comp.bios.tianocore.devel/10545/focus=10550>.)
Cc: Alexander Graf <agraf@suse.de>
Cc: Reza Jelveh <reza.jelveh@tuhh.de>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Gabriel L. Somlo <somlo@cmu.edu>
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Reza Jelveh <reza.jelveh@tuhh.de>
[feng.tian@intel.com: see above]
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
[lersek@redhat.com: updated commit message]
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Tested-by: Gabriel Somlo <somlo@cmu.edu>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18529 6f19259b-4bc3-4df7-8a09-765794883524
In a CloseEvent, an UnregisterProtocolNotify is done unconditionally.
There is a penalty associated with searching the protocol database on
every CloseEvent and impacts performance, especially during Network IO.
Unregister needs to be done only if the Event is for a RegisterProtocolNotify.
So extend the ExFlag in IEVENT to a UINT8 and define new flags that can
be set to indicate if the Event is part of a group, or registered on a
protocol notify. Then in CloseEvent, call UnregisterProtocolNotify only
if the register protocol notify flag is set.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Samer El-Haj-Mahmoud <samer.el-haj-mahmoud@hpe.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18517 6f19259b-4bc3-4df7-8a09-765794883524
Take the range in the resource descriptor HOB for the memory region described
by the PHIT as higher priority if it is big enough. It can make the memory bin
allocated to be at the same memory region with PHIT that has more better compatibility
to avoid memory fragmentation for some code practices assume and allocate <4G ACPI memory.
Also let the minimal memory size needed include the total memory bin size needed to
make sure memory bin could be allocated successfully.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18503 6f19259b-4bc3-4df7-8a09-765794883524
The HOB List relocation should be at after all the tested memory resources added
(except the memory space that covers HOB List) to the memory services,
because the memory resource found in CoreInitializeMemoryServices()
may have not enough remaining resource for HOB List.
And the memory space that covers HOB List should be processed
after HOB List relocation to avoid the resources allocated by others
to corrupt HOB List before its relocation.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Cc: Liming Gao <liming.gao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18499 6f19259b-4bc3-4df7-8a09-765794883524
The pointer to the destination string changed,the max length also changed.Previous change neglect this point.
And base on the code logic,we can use StrCatS to replace StrCpyS.Now this patch is to fix this bug.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18497 6f19259b-4bc3-4df7-8a09-765794883524
Certain PCI device may have capability pointing to itself.
Update LocateCapabilityRegBlock() to break when detecting such loop.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18473 6f19259b-4bc3-4df7-8a09-765794883524
Allow platforms to instantiate this PCD as PcdsDynamic and PcdsDynamicEx
too, not just PcdsFixedAtBuild and PcdsPatchableInModule.
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18468 6f19259b-4bc3-4df7-8a09-765794883524
What to do:
1. Remove a hidden assumption "No SMM driver writes BootScript between
SmmReadyToLock and S3SleepEntryCallback".
1.1. Use SmmExitBootServices and SmmLegacyBoot notification to record
AtRuntime flag.
1.2. Use mBootScriptDataBootTimeGuid LockBox to save boot time boot
script data to handle potential INSERT boot script at runtime in SMM.
2. Do not depend on OS to help restore ACPINvs data and use
EfiReservedMemoryType instead of EfiACPIMemoryNVS.
2.1. Use mBootScriptSmmPrivateDataGuid LockBox to save boot script
SMM private data with BackFromS3 = TRUE at runtime. S3 resume
will help restore it to tell the Library the system is back
from S3.
Why to do:
1. The hidden assumption "No SMM driver writes BootScript between
SmmReadyToLock and S3SleepEntryCallback" will cause confusion to
the library's consumer and block the usage of "SMM driver writes
BootScript after SmmReadyToLock". So Remove the assumption.
2. In original code, there might be a corner case that malicious
code patch ACPINvs boot TableLength field same as SMM boot script.
So that it can skip the table restore. The impact is that BootScript
in SMM may be overridden by malicious code.
--------------------
CopyMem ((VOID*)&TableHeader, (VOID*)mS3BootScriptTablePtr->TableBase, sizeof(EFI_BOOT_SCRIPT_TABLE_HEADER));
if (mS3BootScriptTablePtr->TableLength + sizeof(EFI_BOOT_SCRIPT_TERMINATE) != TableHeader.TableLength) { // TableLength is in NVS
......
//
// NOTE: We should NOT use TableHeader.TableLength, because it is already updated to be whole length.
//
mS3BootScriptTablePtr->TableLength = (UINT32)(mLockBoxLength - sizeof(EFI_BOOT_SCRIPT_TERMINATE)); ? This line can be skipped.
--------------------
So use EfiReservedMemoryType instead of EfiACPIMemoryNVS as the code
has been updated to not depend on OS to help restore ACPINvs data.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18467 6f19259b-4bc3-4df7-8a09-765794883524
The driver binding start function in SNP.c goes through all the BARs and get
the last BAR index for use. Theoretically it should work with all valid BARs,
but we got reports some device did always use the first valid BAR, so we change
the logic in SNP to use the first found BAR index instead of the last one.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Fu Siyuan <siyuan.fu@intel.com>
Reviewed-by: Ye Ting <ting.ye@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18455 6f19259b-4bc3-4df7-8a09-765794883524
The specification of the EFI_EXT_SCSI_PASS_THRU_PROTOCOL.PassThru()
function documents the EFI_BAD_BUFFER_SIZE return status, and the
EFI_EXT_SCSI_STATUS_HOST_ADAPTER_DATA_OVERRUN_UNDERRUN host adapter
status.
These allow an EFI_EXT_SCSI_PASS_THRU_PROTOCOL implementation to request
higher layers in the stack (in this instance, UefiScsiLib and ScsiDiskDxe)
to break up the transfer into smaller pieces.
These conditions percolate up the stack correctly: the retry loops in
ScsiDiskDxe's ScsiDiskReadSectors() and ScsiDiskWriteSectors() functions
correctly and transparently update the transfer size (ByteCount),
accommodating any shortening requested by lower levels of the stack. After
the loop -- if the request ultimately succeeds -- SectorCount is even
recalculated from the final ByteCount, to see how many sectors the outer
loop should advance.
However, the inner (ie. retry) loops both have the same error: when the
underlying protocols request the transfer to be shortened, the decrease in
transfer size (ie. ByteCount) should immediately be reflected in
SectorCount. Otherwise the sector count encoded in the CDB will exceed the
transfer size, which is a permanent error.
This issue has been witnessed while booting
en_windows_8.1_pro_n_vl_with_update_x86_dvd_6051127.iso
on the 32-bit build of OVMF, from a virtio-scsi CD-ROM:
(1) "cdboot.efi" correctly requested (from far atop) a long read:
Timeout=940000000
CdbLength=10
DataDir=Read
InTransferLength=134215680
OutTransferLength=0
SenseDataLength=108
Cdb: 28 00 00 00 25 DD 00 FF FF 00
^ ^^^^^^^^^^^ ^^^^^
| | |
| | number of 2KB sectors to read,
| | corresponding to 2048 * 65535 = 134215680 bytes
| | (see InTransferLength above)
| |
| LBA to read from
|
READ (10)
(2) In turn, the EFI_EXT_SCSI_PASS_THRU_PROTOCOL.PassThru() function
provided by "OvmfPkg/VirtioScsiDxe/VirtioScsi.c" asked for the request
to be shortened:
InTransferLength=16776704
OutTransferLength=16776704
SenseDataLength=0
HostAdapterStatus=EFI_EXT_SCSI_STATUS_HOST_ADAPTER_DATA_OVERRUN_UNDERRUN
TargetStatus=0
Status=EFI_BAD_BUFFER_SIZE
(3) Then ScsiDiskReadSectors() in
"MdeModulePkg/Bus/Scsi/ScsiDiskDxe/ScsiDisk.c" retried the request
with correctly shortened transfer length, but incorrectly unchanged
sector count:
Timeout=940000000
CdbLength=10
DataDir=Read
InTransferLength=16776704 <--- updated as requested
OutTransferLength=0
SenseDataLength=108
Cdb: 28 00 00 00 25 DD 00 FF FF 00
^ ^^^^^^^^^^^ ^^^^^
| | |
| | not changed!
| |
| LBA to read from
|
READ (10)
(4) Since 65535 sectors of 2KB each wouldn't fit in a buffer of approx.
16MB, QEMU's virtio-scsi controller unconditionally rejected this
request with VIRTIO_SCSI_S_OVERRUN, which VirtioScsiDxe then mapped
to:
InTransferLength=16776704
OutTransferLength=0
SenseDataLength=0
HostAdapterStatus=EFI_EXT_SCSI_STATUS_HOST_ADAPTER_DATA_OVERRUN_UNDERRUN
TargetStatus=0
Status=EFI_DEVICE_ERROR
(5) After two more tries of the same, ScsiDiskDxe passed up the error,
which ultimately caused "cdboot.efi" to BSOD.
Many thanks to Larry Cleeton from Microsoft for helping debug
"cdboot.efi".
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18438 6f19259b-4bc3-4df7-8a09-765794883524
Acting specifically upon this error condition from UefiScsiLib (and
ultimately from EFI_EXT_SCSI_PASS_THRU_PROTOCOL.PassThru()) in the
- ScsiDiskRead10(),
- ScsiDiskWrite10(),
- ScsiDiskRead16(),
- ScsiDiskWrite16()
functions allows us to retry these operations from ScsiDiskReadSectors()
and ScsiDiskWriteSectors(), with adjusted transfer sizes, without
investigating further error details like Host Adapter Status, Target
Status, and Sense Data.
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18437 6f19259b-4bc3-4df7-8a09-765794883524
PXE driver's LoadFile protocol should check the input parameter
FilePath to see whether it's a supported device path.If not,
it should return invalid parameter, do not continue PXE boot.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Zhang Lubo <lubo.zhang@intel.com>
Reviewed-by: Fu Siyuan <siyuan.fu@intel.com>
Reviewed-by: Ye Ting <ting.ye@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18435 6f19259b-4bc3-4df7-8a09-765794883524
The mBmPerfHeader.Count isn't reset to 0 in BmWriteBootToOsPerformanceData()
so when the actual performance data entry count exceeds the LimitCount,
the performance data collection breaks on condition
if (mBmPerfHeader.Count == LimitCount), but 2nd time calling this function
will not break on condition if (mBmPerfHeader.Count == LimitCount) because
the mBmPerfHeader.Count always bigger than LimitCount, which results buffer
overrun.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18417 6f19259b-4bc3-4df7-8a09-765794883524
Add driver to produce EFI_REGULAR_EXPRESSION_PROTOCOL. Based on
Oniguruma v5.9.6 (BSD 2-clause license), which provides full Unicode
support, and POSIX ERE and Perl regex syntaxes.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Cecil Sheng <cecil.sheng@hpe.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18413 6f19259b-4bc3-4df7-8a09-765794883524
Add driver to produce EFI_REGULAR_EXPRESSION_PROTOCOL. Based on
Oniguruma v5.9.6 (BSD 2-clause license), which provides full Unicode
support, and POSIX ERE and Perl regex syntaxes.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Cecil Sheng <cecil.sheng@hpe.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18411 6f19259b-4bc3-4df7-8a09-765794883524
Our tool can support OrderedList which has default value,but doesn't update the
source code in HiiDatabase when parse the ifr data.Now update the code and add
test case in DriverSample.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18388 6f19259b-4bc3-4df7-8a09-765794883524
Modified the logic in Ip4Dxe and Ip6Dxe to not locate EFI_IPSEC2_PROTOCOL on each
message transmit/receive. Instead, register a callback in the drivers entry points
on the IpSec protocol installation, and process only if the protocol is installed.
This speeds up the network stacks when IpSec is not installed since there is a
penalty associated with searching the entire handle database on each packet processing.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Samer El-Haj-Mahmoud <samer.el-haj-mahmoud@hp.com>
Reviewed-by: Fu Siyuan <siyuan.fu@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18365 6f19259b-4bc3-4df7-8a09-765794883524
Previously construct Default Value in AltResp for string opcode is String Id,
Now change it to string value if the string opcode has default value.
This change is compatible for SetupBrowser to handle.And add default value
for string in DriverSample to test this case.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18337 6f19259b-4bc3-4df7-8a09-765794883524
Convert the UNIX to DOS end of line format.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiaxin Wu <jiaxin.wu@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18324 6f19259b-4bc3-4df7-8a09-765794883524
There may be anti-flash wear out feature to forbid erase operation after end of dxe.
The code is missing some error handling for erase operation failure,
it should return directly after the erase operation failed.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18320 6f19259b-4bc3-4df7-8a09-765794883524
The error handling for timeout case is enhanced to remove TDs from
transfer ring. The original code only removed s/w URB, but the h/w
transfer descriptor TDs didn't get removed. It would cause data lost
for data stream peripheral, such as usb-to-serial device, from the
s/w perspective.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Baraneedharan Anbazhagan <anbazhagan@hp.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18313 6f19259b-4bc3-4df7-8a09-765794883524
InternalIsBufferOverlapped() is created to check overlap between buffers.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18312 6f19259b-4bc3-4df7-8a09-765794883524
in case PeiInstallPeiMemory() is done in a callback with
EFI_PEI_PPI_DESCRIPTOR_NOTIFY_DISPATCH, and the callback is registered on
a PPI that is installed in the last PEIM.
At the case, PeiCore SwitchStack code will be not being invoked.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18305 6f19259b-4bc3-4df7-8a09-765794883524
The check will be based on PcdVarCheck binary that generated
by BaseTools.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18294 6f19259b-4bc3-4df7-8a09-765794883524
The check will be based on VarCheckHiiBin that generated
from FV and Hii Database.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18293 6f19259b-4bc3-4df7-8a09-765794883524
Since the variable check service has be separated to VarCheckLib
from Variable driver, so update Variable driver to consume the
separated VarCheckLib.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18286 6f19259b-4bc3-4df7-8a09-765794883524
What to do: Implement VarCheckUefiLib NULL class library instance.
The code logic are separated from Variable driver, and it will consume VarCheckLib
to register var check handler and variable property set for UEFI defined variables.
Why to do: Share code.
Separate variable check UEFI code from Variable driver in MdeModulePkg.
We are going to separate generic software logic code from Variable Driver
to benefit other variable driver implementation. Auth services has been done
to be AuthVariableLib, now to cover variable check service.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18279 6f19259b-4bc3-4df7-8a09-765794883524
What to do:
1. Add VarCheckLib LibraryClass definitions.
2. Implement VarCheckLib library instance.
The code logic are separated from Variable driver.
Why to do: Share code.
Separate variable check service from Variable driver in MdeModulePkg.
We are going to separate generic software logic code from Variable Driver
to benefit other variable driver implementation. Auth services has been done
to be AuthVariableLib, now to cover variable check service.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18278 6f19259b-4bc3-4df7-8a09-765794883524
Check the local variable 'NameSpace' before use it.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Qiu Shumin <shumin.qiu@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18274 6f19259b-4bc3-4df7-8a09-765794883524
In current UiApp/Boot Maintenance manager,some pages don't support F10,
they use Commit Changes and Exit menu to save changes.Now support F10
in these pages.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18249 6f19259b-4bc3-4df7-8a09-765794883524
Ip4StartAutoConfig() will always free its default router table and interface,
which may cause IP instance missing its correct default interface. e.g. when
the policy is dhcp, and one child is configured to use default address.
Cc: Ye Ting <ting.ye@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiaxin Wu <jiaxin.wu@intel.com>
Reviwed-by: Ye Ting <ting.ye@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18245 6f19259b-4bc3-4df7-8a09-765794883524
In the original code, there exists some mismatches between the real
waiting time and the corresponding timeout comments. For example, the
XHC_GENERIC_TIMEOUT comment says it's 10ms timeout value, but the real
code in fact waits 10s.
So the code is refined to be consistent in code logic and comments.
Note XHC_POLL_DELAY macro also be removed and the polling interval in
XhcWaitOpRegBit() is changed from 1ms to 1us to keep same code style
with other code. It has no real functionality impact.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18235 6f19259b-4bc3-4df7-8a09-765794883524
v2:
* Update the MediaPresent detect declaring.
IP4 driver should re-initiate a DHCP if it detects that there is a network.
To fix this issue, we can implement the DHCP re-initiate policy while the media
change detected. The Ip4 driver should set a timer to signal the Ip4 to run the
DHCP configuration again(D.O.R.A). IP4 driver should free old IP address related
resource, then initiate a DHCP process to acquire new IP.
Cc: Ye Ting <ting.ye@intel.com>
Cc: Zhang Lubo <lubo.zhang@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiaxin Wu <jiaxin.wu@intel.com>
Reviewed-by: Ye Ting <ting.ye@intel.com>
Reviewed-by: Lubo Zhang <lubo.zhang@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18232 6f19259b-4bc3-4df7-8a09-765794883524
between variable HOB and NV storage.
Variable HOB may be built by a system that supports and loads variable
default, the variables in the HOB will be flush to NV storage after
variable write search ready.
After that, if the variable's Attributes is changed by someone and
system reboots and tries to load default again, the variable Attributes
mismatch case between variable HOB and NV storage will appear.
Original code did not handle the case correctly, that may eventually
cause NV storage contains two valid same variables that will lead to
system hang if GetNextVariableName() called.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18225 6f19259b-4bc3-4df7-8a09-765794883524
When add driver option using file,input the description and then commit changes and exit,
it doesn't work.it caused by the commit 18216.When variable DriverOrderList in Variable.c
is NULL,it also need do the follow path,shouldn't return.Now change the code.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Qiu Shumin <shumin.qiu@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18220 6f19259b-4bc3-4df7-8a09-765794883524
Refine the code in UiApp to prevent the potential risk.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Qiu Shumin <shumin.qiu@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18216 6f19259b-4bc3-4df7-8a09-765794883524
Replace the unsafe string functions with the safe one in UiApp.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Qiu Shumin <shumin.qiu@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18214 6f19259b-4bc3-4df7-8a09-765794883524
In HttpLib, the Event BodyParseComplete should return to the
callback function when the whole message body has been parsed
including the trailer if it has.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Zhang Lubo <lubo.zhang@intel.com>
Reviewed-by: Ye Ting <ting.ye@intel.com>
Reviewed-by: Wu Jiaxin <jiaxin.wu@intel.com>
Reviewed-by: Fu Siyuan <siyuan.fu@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18213 6f19259b-4bc3-4df7-8a09-765794883524
DHCP policy is applied as default at boot time on all NICs in the system, which results
in all NIC ports attempting DHCP and trying to acquire IP addresses during boot.
Ip4 driver should only set dhcp as default policy, and not trigger DORA at driver binding
start(). We should start DORA until one IP child is configured to use default address.
Cc: Fu Siyuan <siyuan.fu@intel.com>
Cc: Ye Ting <ting.ye@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiaxin Wu <jiaxin.wu@intel.com>
Reviewed-by: Ye Ting <ting.ye@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18201 6f19259b-4bc3-4df7-8a09-765794883524
Change a macro name to fit EDK2 naming conventions: Use all capital letters for #define.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: fanwang2 <fan.wang@intel.com>
Reviewed-by: Jiaxin Wu <jiaxin.wu@intel.com>
Reviewed-by: Qiu Shumin <shumin.qiu@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18200 6f19259b-4bc3-4df7-8a09-765794883524
Got the build failure feedback below, this patch is to fix that.
This broke the IA32 Ovmf build for me, with GCC 5.1.1 (Fedora 22):
/home/dwmw2/git/edk2/MdeModulePkg/Core/DxeIplPeim/Ia32/DxeLoadFunc.c:377:7:
error: ‘PageTables’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
AsmWriteCr3 (PageTables);
^
/home/dwmw2/git/edk2/MdeModulePkg/Core/DxeIplPeim/Ia32/DxeLoadFunc.c:224:9:
note: ‘PageTables’ was declared here
UINTN PageTables;
^
cc1: all warnings being treated as errors
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Qiu Shumin <shumin.qiu@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18190 6f19259b-4bc3-4df7-8a09-765794883524
NetRandomInitSeed() function use current time to initialize the random seed,
while in some platform the time service is not accuracy that make the random
seed collision. This patch add the monotonic count to the seed to avoid this.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Fu Siyuan <siyuan.fu@intel.com>
Reviewed-by: Jiaxin Wu <jiaxin.wu@intel.com>
Reviewed-by: Ye Ting <ting.ye@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18185 6f19259b-4bc3-4df7-8a09-765794883524
EDKII usb stack is using a TPL_CALLBACK timer to monitor async transfer
request and signal event if it's done. As usb enumeration and usb mass
storage block i/o read/write runs on TPL_CALLBACK and TPL_NOTIFY level
respectively, It blocks usb async transfer requests, usually usb mouse
/use kb, getting time to run.
Without this change, user couldn't get usb mouse/kb state in time (will
show a little lag from UI view) when there is other usb transactions, such
as a new usb device inserted.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18169 6f19259b-4bc3-4df7-8a09-765794883524
This feature is added for UEFI spec that says
"Stack may be marked as non-executable in identity mapped page tables".
A PCD PcdSetNxForStack is added to turn on/off this feature, and it is
FALSE by default.
Cc: Jiewen Yao <jiewen.yao@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: "Yao, Jiewen" <Jiewen.yao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18166 6f19259b-4bc3-4df7-8a09-765794883524
Once the question is refreshed,the processing should happen in the callback function
of EFI_BROWSER_ACTION_RETRIEVE case,rather than EFI_BROWSER_ACTION_CHANGING in DriverSample.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18150 6f19259b-4bc3-4df7-8a09-765794883524
to right after CoreInitializeGcdServices().
Why?
Some platforms maybe report both below 4G and above 4G memory resource hob as tested,
then CoreInitializeMemoryServices() will find and add the tested above 4G memory resource hob to memory descriptor for early memory allocation services,
then if ProcessLibraryConstructorList() that has library constructor tries to allocate below 4G memory and will fail.
In fact, the following CoreInitializeGcdServices() will add all the memory resource hob to GCD map,
and add the tested below 4G memory resource hob to memory descriptor,
but it has been too late for ProcessLibraryConstructorList().
Also move below two lines as they are needed to be after
the constructor of DxeCorePerfomanceLib.
PERF_END (NULL,"PEI", NULL, 0) ;
PERF_START (NULL,"DXE", NULL, 0) ;
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18146 6f19259b-4bc3-4df7-8a09-765794883524
If the storage of the question is EFI_HII_VARSTORE_BUFFER/EFI_HII_VARSTORE_EFI_VARIABLE_BUFFER,
in SetupBrowserDxe the configuration stings contain uppercase,but HiiDataBaseDxe generates the
ConfigResp string in lowercase,they mismatch,so FindQuestionFromProgress function is broken.
Now convert the configuration string in SetupBrowserDxe to lowercase to fix this issue.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18143 6f19259b-4bc3-4df7-8a09-765794883524
v2 changelog:
Check CurrentPeimHandle to check the matched PeimHandle.
Add check point to ShadowPeiCore based on PCD.
v1 changelog:
PeiCore LoadImage always shadow itself and PEIM on normal boot after
the physical memory is installed. On the emulator platform, the shadow
may be not necessary. To support such usage, new PCD PcdShadowPeimOnBoot
is introduced to specify whether loads PEIM in memory by default.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18125 6f19259b-4bc3-4df7-8a09-765794883524
According to the PCI spec, when software writes all-one to BAR for size probing,
the value read back should be 0b1...10...0 after masking the BAR type bits.
But in real world, it's possible that certain device returns 0b0...01...10...0
for MEM64 BAR size probing: some bits in the high 32bit may be 0.
PciBus driver has the code to handle such case. However, it doesn't handle the
case that the high 32bit is totally 0. The patch is to handle the special case.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18114 6f19259b-4bc3-4df7-8a09-765794883524
This is the UI part of the old BdsDxe driver, also remove the legacy boot option related code.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18111 6f19259b-4bc3-4df7-8a09-765794883524
The logic in an if statement in PciIo is too complex and hard to understand
and make VS2015 build failure. The fix simplifies the logic.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Michael D Kinney <michael.d.kinney@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18109 6f19259b-4bc3-4df7-8a09-765794883524
This fix is used to solve VS2015 warning "local variable is not initialized before use"
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Michael D Kinney <michael.d.kinney@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18108 6f19259b-4bc3-4df7-8a09-765794883524
DHCP4 service allows only one of its children to be configured
in the active state,If the DHCP4 D.O.R.A started by IP4 auto
configuration and has not been completed, the Dhcp4 state machine
will not be in the right state for the PXE to start a new round
D.O.R.A., so we need to switch it's policy to static.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Zhang Lubo <lubo.zhang@intel.com>
Reviewed-by: Fu Siyuan <siyuan.fu@intel.com>
Reviewed-by: Wu Jiaxin <jiaxin.wu@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18107 6f19259b-4bc3-4df7-8a09-765794883524
It was forgotten to be included in MdeModulePkg.dsc when created.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18105 6f19259b-4bc3-4df7-8a09-765794883524
GLOBAL_REMOVE_IF_UNREFERENCED means __declspec(selectany) for MS tool
chain IA32/X64 build.
According to MSDN, "selectany" would tell the compiler that the declared
global data item (variable or object) is a pick-any COMDAT (a packaged
function). At link time, if multiple definitions of a COMDAT are seen,
the linker picks one and discards the rest.
So we have to remove GLOBAL_REMOVE_IF_UNREFERENCED key word from two global
variable's extern definitions of .h file as we have used this keyword in
.c file, otherwise the MS tool chain would pick the definitions in .h file
and treat it as uninitialized data to generate full-0 content for these two
global variables.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18088 6f19259b-4bc3-4df7-8a09-765794883524
to instead of AllocatePool() to ensure the data is clean for
the following consumption.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18087 6f19259b-4bc3-4df7-8a09-765794883524
When load default value or save changes will pop up message box to let user
confirm,Y means confirm and N means ignore,now add Esc key with the
same function of N key.And change the content of pop up message in .uni file,
now will display "Press 'Y' to confirm, 'N'/'ESC' to ignore."
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18076 6f19259b-4bc3-4df7-8a09-765794883524
Enhance the setupbrowserdxe to output debug message when DisplayEngineDxe is
not installed and this will be easy for user to find the reason why can not
enter Setup page.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18075 6f19259b-4bc3-4df7-8a09-765794883524
Reduce reserved memory consumption by page table buffer,
then OS can have more available memory to use.
Take PhysicalAddressBits = 48 and 2MB page granularity as example,
1:1 Virtual to Physical identity mapping page table buffer needs to be
((512 + 1) * 512 + 1) * 4096 = 1075843072 bytes = 0x40201000 bytes.
The code is updated to only allocate 2 pages (1G page enabled) or
6 pages for 4G page table, and 8 extra pages to handles > 4G request
by page fault.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18070 6f19259b-4bc3-4df7-8a09-765794883524
We are going to reduce reserved memory consumption by page table buffer,
then OS can have more available memory to use.
Take PhysicalAddressBits = 48 and 2MB page granularity as example,
1:1 Virtual to Physical identity mapping page table buffer needs to be
((512 + 1) * 512 + 1) * 4096 = 1075843072 bytes = 0x40201000 bytes.
The code is updated to build 4G page table by default and only use 8 extra
pages to handles > 4G request by page fault.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18069 6f19259b-4bc3-4df7-8a09-765794883524
We are going to reduce reserved memory consumption by page table buffer,
then OS can have more available memory to use.
Take PhysicalAddressBits = 48 and 2MB page granularity as example,
1:1 Virtual to Physical identity mapping page table buffer needs to be
((512 + 1) * 512 + 1) * 4096 = 1075843072 bytes = 0x40201000 bytes.
Current BootScriptExecutorDxe handles > 4G request by page fault because
S3ResumePeim only builds 4G page table when long mode waking vector is
not needed, but BootScriptExecutorDxe still assume the page table buffer for
page table is at 1:1 Virtual to Physical identity mapping.
To reduce reserved memory consumption, the code is updated to only use
8 extra pages to handles > 4G request by page fault.
Another, when both BIOS and OS wants long mode waking vector,
S3ResumePei should have established 1:1 Virtual to Physical identity mapping
page table for ACPI spec requirement, so no need to hook page fault handler.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18067 6f19259b-4bc3-4df7-8a09-765794883524
As variable HEADER_ALIGNMENT = 4, the MonotonicCount in
AUTHENTICATED_VARIABLE_HEADER may be not UINT64 aligned,
so go to use ReadUnaligned64() to ensure read data correctly.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18064 6f19259b-4bc3-4df7-8a09-765794883524
When there are multiple network boot options, user will see multiple
"UEFI Network" boot options. It's hard to distinguish them using the
description.
The patch enhances the boot option generation logic to append " 2"
/" 3"/" 4"/... number suffix to the non-first network boot options.
So the 2nd one becomes "UEFI Network 2".
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Eric Dong <eric.dong@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18062 6f19259b-4bc3-4df7-8a09-765794883524
GatewayIpAddress and SubnetMask do not exist in old IPv4_DEVICE_PATH, this
will lead new IScsiDxe to error if IPv4_DEVICE_PATH in system is not
updated.
Following UEFI2.5 spec of IPv4_DEVICE_PATH do a check before accessing
fields only defined in new version, add a judgement here to make old
IPv4_DEVICE_PATH and new IScsiDxe can cowork.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: fanwang2 <fan.wang@intel.com>
Reviewed-by: Ye Ting <ting.ye@intel.com>
[lersek@redhat.com: rewrapped commit message]
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18057 6f19259b-4bc3-4df7-8a09-765794883524
When mismatch happens,there exists one case that exit current
form and display last form.Assert code don't cover this case.
Now add check to handle this situation.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18053 6f19259b-4bc3-4df7-8a09-765794883524
The first parameter of match2 opcode should be the pattern
and the second one should be the string.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18052 6f19259b-4bc3-4df7-8a09-765794883524
if the instance of the DHCP4 protocol driver is in the Dhcp4Bound
status that is DHCP configuration has completed, so the Dhcp4->Start
FUNC in the EfiPxcBcDhcp() will return EFI_ALREADY_STARTED status
which lead to EfiPxeBcDhcp FUNC not in correspondence with UEFI spec.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Zhang Lubo <lubo.zhang@intel.com>
Reviewed-by: Fu Siyuan <siyuan.fu@intel.com>
Reviewed-by: Ye Ting <ting.ye@intel.com>
[lersek@redhat.com: updated copyright year as Siyuan asked]
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18050 6f19259b-4bc3-4df7-8a09-765794883524
Fix git 59a8cfd4 (SVN r17869) removes DHCP4.TransmitReceive()and DORA
process dependency, but it updated TransmitReceive() to take the ownership
of DhcpSb->ActiveChild but never release it. This will break the retransmit
and lease time out counter of DORA.
To fix that, TransmitReceive() doesn't need to be the ActiveChild, and the
timer routine should be updated to handle the TransmitReceive specially.
Cc: Fu Siyuan <siyuan.fu@intel.com>
Cc: Ye Ting <ting.ye@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiaxin Wu <jiaxin.wu@intel.com>
Reviewed-by: Fu Siyuan <siyuan.fu@intel.com>
Reviewed-by: Ye Ting <ting.ye@intel.com>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18048 6f19259b-4bc3-4df7-8a09-765794883524
This driver is soon going to be built by ArmVirtPkg/ArmVirtQemu.dsc
(without any changes). Although VALID_ARCHITECTURES is not used by the
build system (it is just a comment), it is best kept up-to-date for human
readers' sake.
Cc: Feng Tian <feng.tian@intel.com>
Cc: Elvin Li <elvin.li@intel.com>
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18041 6f19259b-4bc3-4df7-8a09-765794883524
that assumes the SMRAM reserved range is only at the end of the SMRAM descriptor.
//
// This range has reserved area, calculate the left free size
//
gSmmCorePrivate->SmramRanges[Index].PhysicalSize = SmramResRegion->SmramReservedStart - gSmmCorePrivate->SmramRanges[Index].CpuStart;
Imagine the following scenario where we just reserve the first page of the SMRAM range:
SMRAM Descriptor:
Start: 0x80000000
Size: 0x02000000
Reserved Range:
Start: 0x80000000
Size: 0x00001000
In this case the adjustment to the SMRAM range size yields zero: ReservedStart - SMRAM Start is 0x80000000 - 0x80000000 = 0.
So even though most of the range is still free the IPL code decides its unusable.
The problem comes from the email thread: [edk2] PiSmmIpl SMRAM Reservation Logic.
http://thread.gmane.org/gmane.comp.bios.tianocore.devel/15268
Also to follow the idea in the email thread, the patch is to
1. Keep only one copy of full SMRAM ranges in gSmmCorePrivate->SmramRanges,
split record for SmmConfiguration->SmramReservedRegions and SMM Core that
will be marked to be EFI_ALLOCATED in gSmmCorePrivate->SmramRanges.
2. Handle SmmConfiguration->SmramReservedRegions at beginning of, at end of,
in the middle of, or cross multiple SmramRanges.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18031 6f19259b-4bc3-4df7-8a09-765794883524
1. Get default terminal type from PCD rather than using PCANSI
directly in BuildTeminalDevpath;
2. Only terminal type is needed to create an TerminalDev instance, so
remove the useless code of creating and freeing DefaultNode.
3. Some white space refining.
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Heyi Guo <heyi.guo@linaro.org>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18027 6f19259b-4bc3-4df7-8a09-765794883524
This is bug fix for TerminalDxe: NullRemaining should be set to FALSE
by fault and then be set to TRUE conditionally.
Cc: Feng Tian <feng.tian@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Heyi Guo <heyi.guo@linaro.org>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18026 6f19259b-4bc3-4df7-8a09-765794883524
Change the type of mStatusString[] to reflect that it is a CONST
array of pointers to CONST.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jaben Carsey <jaben.carsey@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18022 6f19259b-4bc3-4df7-8a09-765794883524
Add the check at DxeLoadCore() on MdeModulePkg\Core\DxeIplPeim\DxeLoad.c
to skip install the "gEfiMemoryTypeInformationGuid" hob if it is already
installed.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@18018 6f19259b-4bc3-4df7-8a09-765794883524
Remove two protocols never used in DxeNetLib.inf and add HttpLib access in MdeModulePkg.dec.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: fanwang2 <fan.wang@intel.com>
Reviewed-by: Fu Siyuan <siyuan.fu@intel.com>
Reviewed-by: Jiaxin Wu <jiaxin.wu@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17983 6f19259b-4bc3-4df7-8a09-765794883524
Ip4ConfigDxe driver is deprecated in UEFI 2.5, so we will not support original Ip4Config Protocol,
which is replace by Ip4Config2 Protocol integrated in Ip4Dxe driver(git commit 1f6729ff (SVN r17853)).
Dependent network drivers, libraries and applications have been migrated to (or extended to) the new protocol version.
For example:
git 7c25b7ea (SVN r17869): ping & ifconfig
git 00a6ad1b (SVN r17870): UefiHandleParsingLib
git 6c5c70d6 (SVN r17873): DxeNetLib
git 39561686 (SVN r17874): IpSecDxe
git c581e503 (SVN r17875): EfiSocketLib
This patch is based on related packages(MdeModulePkg, Nt32Pkg, ArmPlatformPkg, ArmVirtPkg, EmulatorPkg, OvmfPkg, Vlv2TbltDevicePkg) clean-up work finished.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jiaxin Wu <jiaxin.wu@intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17917 6f19259b-4bc3-4df7-8a09-765794883524
In certain rare circumstance, the data passed from outside of SMM may be
invalid resulting the integer overflow. The issue are found by code review.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17908 6f19259b-4bc3-4df7-8a09-765794883524
FvSimpleFileSystem adds '.efi' to the EFI application and drivers
filenames even through this extension is not present in the real
filename of the EFI module.
In the current behaviour, it would not be possible to open an EFI
application using FvSimpleFileSystem if the extension has been omitted
in the given filename.
It can be create some confusion if someone wants to try to
open a file with the real application name (eg: 'Shell').
This patch adds support to try again to look for the file with the
extension if it had failed to find it without the extension.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <Olivier.Martin@arm.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17903 6f19259b-4bc3-4df7-8a09-765794883524
Accept the VT220 escape code [3~ as backspace for TtyTerm terminals. This is
sent by many Linux terminals by default. Also accept VT220 function keys
F1-F12, and VT100 F1-F4 keys as these are commonly sent by Linux terminals.
The VT220 escape codes are longer, and variable length so a new state is added
to the state machine along with a variable to construct the multibyte escape
sequence.
There are currently no ambiguous escape sequence prefixes accepted, so the TTY
terminal accepts escape sequences for a variety of terminals. The goal is to
'just work' with as many terminals as possible, rather than properly emulating
any specific terminal. Backspace, Del, and F10 have been tested on xterm,
rxvt, tmux, and screen.
Note: The existing vt100 function key handling does not match the vt100
documentation that I found, so I added the TTY terminal handling
of VT100 F1-F4 (really PF1-PF4 on vt100) separately. The vt100
has no F5-F10 keys, so I don't know what the current vt100 code
is based on.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Roy Franz <roy.franz@linaro.org>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17897 6f19259b-4bc3-4df7-8a09-765794883524
Treat ASCII 0x7F as backspace, rather than delete, for TTY terminals. This
better matches the default Linux terminal settings that are used when connecting
to a simulated platform using xterm or a similar terminal program.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Roy Franz <roy.franz@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17896 6f19259b-4bc3-4df7-8a09-765794883524
This patch a adds new terminal type, TtyTerm, to TerminalDxe. This terminal
type provides a place to add support for various *nix terminals that don't
behave like standard VT terminals. The goal is to 'just work' with as many
terminals as possible, rather than properly emulating any one specific
terminal.
Signed-off-by: Roy Franz <roy.franz@linaro.org>
Contributed-under: TianoCore Contribution Agreement 1.0
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17895 6f19259b-4bc3-4df7-8a09-765794883524
UEFI spec has clear description below:
Configuration Table Groups
The GUID for a configuration table also defines a corresponding event group GUID with the same value.
If the data represented by a configuration table is changed,
InstallConfigurationTable() should be called.
When InstallConfigurationTable() is called, the corresponding event is signaled.
When this event is signaled,
any components that cache information from the configuration table can optionally update their cached state.
For example, EFI_ACPI_TABLE_GUID defines a configuration table for ACPI data.
When ACPI data is changed, InstallConfigurationTable() is called.
During the execution of InstallConfigurationTable(),
a corresponding event group with EFI_ACPI_TABLE_GUID is signaled,
allowing an application to invalidate any cached ACPI data.
But current implementation only InstallConfigurationTable() at first time ACPI data change.
if (((Version & EFI_ACPI_TABLE_VERSION_1_0B) != 0) &&
!AcpiTableInstance->TablesInstalled1) {
Status = gBS->InstallConfigurationTable (&gEfiAcpi10TableGuid, AcpiTableInstance->Rsdp1);
if (EFI_ERROR (Status)) {
return EFI_ABORTED;
}
AcpiTableInstance->TablesInstalled1 = TRUE;
}
if (((Version & ACPI_TABLE_VERSION_GTE_2_0) != 0) &&
!AcpiTableInstance->TablesInstalled3) {
Status = gBS->InstallConfigurationTable (&gEfiAcpiTableGuid, AcpiTableInstance->Rsdp3);
if (EFI_ERROR (Status)) {
return EFI_ABORTED;
}
AcpiTableInstance->TablesInstalled3= TRUE;
}
The AcpiTableInstance->TablesInstalled1 and AcpiTableInstance->TablesInstalled3 conditional judgment need to be removed.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17885 6f19259b-4bc3-4df7-8a09-765794883524
Safe string functions may ASSERT when the source length is larger than the MaxDest. This patch use Strn**S to indicate the copy length.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Qiu Shumin <shumin.qiu@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17867 6f19259b-4bc3-4df7-8a09-765794883524
The call in ProbeMediaStatus() to the ReadDisk() function of the
EFI_DISK_IO_PROTOCOL interface implemented in DiskIoDxe/DiskIo.c
crashed in DiskIo2ReadWriteDisk() because of the NULL value of
the destination buffer pointer.
Pass the address of a buffer in the stack instead of a NULL
pointer.
In addition to avoiding the crash, that way, the media probe does not
depend anymore on the way the EFI_DISK_IO_PROTOCOL implementation deals
with a NULL value of the destination buffer pointer as the UEFI
specification does not specify the expected behaviour.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ronald Cron <Ronald.Cron@arm.com>
Reviewed-by: Olivier Martin <olivier.martin@arm.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17859 6f19259b-4bc3-4df7-8a09-765794883524
This patch add the header file and DXE implementation for the HttpLib.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Fu Siyuan <siyuan.fu@intel.com>
Reviewed-by: Ye Ting <ting.ye@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17856 6f19259b-4bc3-4df7-8a09-765794883524
and also add new UI configuration support in Ip4Dxe driver.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: jiaxinwu <jiaxin.wu@intel.com>
Reviewed-by: Ye Ting <ting.ye@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17853 6f19259b-4bc3-4df7-8a09-765794883524
MdeModulePkg has defined gZeroGuid in 'Guid/ZeroGuid.h', therefore, the
mZeroGuid defined in Universal/Variable/RuntimeDxe is redundant.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Jaben Carsey <jaben.carsey@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17840 6f19259b-4bc3-4df7-8a09-765794883524
MdeModulePkg has defined gZeroGuid in 'Guid/ZeroGuid.h', therefore, the
gZeroGuid defined in SetupBrowserDxe is redundant.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Jaben Carsey <jaben.carsey@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17839 6f19259b-4bc3-4df7-8a09-765794883524
GCD Range is byte address. EFI memory range is page address. To make sure
GCD range is converted to EFI memory range, the following things are added:
1. Merge adjacent GCD range first.
2. Add ASSERT check on GCD range alignment.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17813 6f19259b-4bc3-4df7-8a09-765794883524
The splitting of memory regions into code and data regions violates
architecture specific alignment rules by using a fixed alignment
of 4 KB. Replace it with EFI_ACPI_RUNTIME_PAGE_ALLOCATION_ALIGNMENT,
which is defined appropriately on each architecture.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: "Jaben Carsey" <jaben.carsey@intel.com>
Reviewed-by: "Yao, Jiewen" <Jiewen.Yao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17812 6f19259b-4bc3-4df7-8a09-765794883524
Move the definitions of EFI_ACPI_RUNTIME_PAGE_ALLOCATION_ALIGNMENT and
DEFAULT_PAGE_ALLOCATION to DxeMain.h to make them available explicitly
to all parts of DxeCore.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: "Yao, Jiewen" <Jiewen.Yao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17811 6f19259b-4bc3-4df7-8a09-765794883524
This removes the functions RevertRuntimeMemoryMap () and
DumpMemoryMap () which are not referenced anywhere in the code.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: "Yao, Jiewen" <Jiewen.Yao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17808 6f19259b-4bc3-4df7-8a09-765794883524
UEFI Spec HTTP Boot Device Path, after retrieving the boot resource
information, the BootURI device path node will be updated to include
the BootURI information. It means the device path on the child handle
will be updated after the LoadFile() service is called.
To handle this case, DxeCore LoadImage() service is updated as the below:
1) Get Device handle based on Device Path
2) Call LoadFile() service (GetFileBufferByFilePath() API) to get Load File Buffer.
3) Retrieve DevicePath from Device handle
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17799 6f19259b-4bc3-4df7-8a09-765794883524
UEFI Spec HTTP Boot Device Path, after retrieving the boot resource
information, the BootURI device path node will be updated to include
the BootURI information. It means the device path on the child handle
will be updated after the LoadFile() service is called.
To handle this case, UefiBootManagerLib BmGetLoadOptionBuffer API
is updated as the below:
1) Get Device handle based on Device Path
2) Call LoadFile() service (GetFileBufferByFilePath() API) to get Load File Buffer.
3) Retrieve DevicePath from Device handle
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17798 6f19259b-4bc3-4df7-8a09-765794883524
UEFI Spec HTTP Boot Device Path, after retrieving the boot resource
information, the BootURI device path node will be updated to include
the BootURI information. It means the device path on the child handle
will be updated after the LoadFile() service is called.
To handle this case, SecurityManagementLib ExecuteSecurityHandlers API
is updated as the below:
1) Get Device handle based on Device Path
2) Call LoadFile() service (GetFileBufferByFilePath() API) to get Load File Buffer.
3) Retrieve DevicePath from Device handle
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17797 6f19259b-4bc3-4df7-8a09-765794883524
1. When Property->Attributes == 0, don't check input Attributes.
2. Enhance comments to be indent aligned and debug message
to be aligned with other messages.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17794 6f19259b-4bc3-4df7-8a09-765794883524
What to do:
1. Merge from Auth Variable driver in SecurityPkg to Variable drive in
MdeModulePkg. Then the merged Variable driver in MdeModulePkg will
link to AuthVariableLib and TpmMeasurementLib.
AuthVariableLibNull and TpmMeasurementLibNull in MdeModulePkg
could be used for non auth variable support.
AuthVariableLib and DxeTpmMeasurementLib in SecurityPkg
may be used for auth variable support.
Why to do:
1. Remove code duplication and reduce maintenance effort.
After auth variable service separated from Auth Variable driver in SecurityPkg
to AuthVariableLib. The remaining code logic of Auth Variable driver in SecurityPkg
will be almost same with Variable driver in MdeModulePkg. Now it is to
merge them.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17765 6f19259b-4bc3-4df7-8a09-765794883524
What to do:
1. Add AuthVariableLib LibraryClass definitions.
2. Implement a NULL AuthVariableLib library instance.
3. Add VARIABLE_ENTRY_PROPERTY definition to VarCheck.h.
4. Add VARIABLE_ENTRY_CONSISTENCY and variable attribute
combinations definitions to VariableFormat.h.
Why to do:
1. Share code.
1.1. Separate auth variable service from Auth Variable driver in
SecurityPkg to AuthVariableLib. Then the AuthVariableLib could benefit
and be used by different implementation of Auth Variable drivers.
1.2 The VARIABLE_ENTRY_PROPERTY definition to VarCheck.h,
VARIABLE_ENTRY_CONSISTENCY and variable attribute
combinations definitions to VariableFormat.h will be shared
by merged Variable driver and AuthVariableLib.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17757 6f19259b-4bc3-4df7-8a09-765794883524
What to do:
1. Merge from VariablePei in SecurityPkg to VariablePei in MdeModulePkg.
Why to do:
1. Remove code duplication and reduce maintenance effort.
The code logic of VariablePei in SecurityPkg is same with VariablePei
in MdeModulePkg.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17756 6f19259b-4bc3-4df7-8a09-765794883524
What to do:
1. Merge VariableInfo in SecurityPkg to VariableInfo in MdeModulePkg.
Why to do:
1. Remove code duplication and reduce maintenance effort.
The functionality of VariableInfo in SecurityPkg has covered VariableInfo
in MdeModulePkg.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17755 6f19259b-4bc3-4df7-8a09-765794883524
What to do:
1. Move authenticated variable definition from AuthenticatedVariableFormat.h
to VariableFormat.h with gEfiAuthenticatedVariableGuid and
AUTHENTICATED_VARIABLE_HEADER.
Why to do:
1. Share code.
We are moving forward to separate auth variable service from Auth Variable
driver in SecurityPkg to AuthVariableLib. Then the AuthVariableLib could benefit
and be used by different implementation of Auth Variable drivers.
2. Remove code duplication and reduce maintenance effort.
After auth variable service separated from Auth Variable driver in SecurityPkg
to AuthVariableLib. The remaining code logic of Auth Variable driver in SecurityPkg
will be almost same with Variable driver in MdeModulePkg. We are going to
merge them.
3. gEfiAuthenticatedVariableGuid will be used by both merged Variable driver
and AuthVariableLib, AUTHENTICATED_VARIABLE_HEADER will be used by
merged Variable driver.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17754 6f19259b-4bc3-4df7-8a09-765794883524
What to do:
1. Move TpmMeasurementLib LibraryClass from SecurityPkg to MdeModulePkg.
2. Implement a NULL TpmMeasurementLib library instance.
Why to do:
1. Share code.
We are moving forward to separate auth variable service from Auth Variable
driver in SecurityPkg to AuthVariableLib. Then the AuthVariableLib could benefit
and be used by different implementation of Auth Variable drivers.
2. Remove code duplication and reduce maintenance effort.
After auth variable service separated from Auth Variable driver in SecurityPkg
to AuthVariableLib. The remaining code logic of Auth Variable driver in SecurityPkg
will be almost same with Variable driver in MdeModulePkg. We are going to
merge them.
3. TpmMeasurementLib is consumed by Auth Variable driver in SecurityPkg now,
as Auth Variable driver in SecurityPkg will be merged to Variable driver in
MdeModulePkg, so the library class also needs to be moved to MdeModulePkg.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17753 6f19259b-4bc3-4df7-8a09-765794883524
The TPer Reset operation would be moved into SecurityPkg/Tcg/
MemoryOverwriteControl/TcgMor.inf module and be triggered at EndOfDxe.
By this way, all encrypted drives which produce EFI_STORAGE_SECURITY_
RPOTOCOL interface would be force reset when MOR is set.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Tian Feng <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17717 6f19259b-4bc3-4df7-8a09-765794883524
Child FV may be placed in parent FV image without process required. Then,
Child FV and parent FV will be in the same continuous space. For FileHandle,
FileHandleToVolume() function needs to find the best matched FV handle.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17704 6f19259b-4bc3-4df7-8a09-765794883524
UEFI2.5 spec, GetMemoryMap(), says:
Attribute: Attributes of the memory region that describe the bit mask
of capabilities for that memory region, and not necessarily the current
settings for that memory region.
But, GetMemoryMap() implementation doesn't append memory capabilities
for MMIO and Reserved memory range. This will break UEFI2.5 Properties
Table feature, because Properties Table need return EFI_MEMORY_RO or
EFI_MEMORY_XP capabilities for OS.
This patch appends memory capabilities for those memory range.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17703 6f19259b-4bc3-4df7-8a09-765794883524
Per PI spec all allocation of SMRAM should use EfiRuntimeServicesCode or EfiRuntimeServicesData.
So SMM instance use EfiRuntimeServicesCode as the default memory allocation type instead of EfiBootServicesData.
This patch clarify this usage in comments.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Qiu Shumin <shumin.qiu@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17667 6f19259b-4bc3-4df7-8a09-765794883524
in function scope that are assigned but never used afterwards.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Wu Jiaxin <jiaxin.wu@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17664 6f19259b-4bc3-4df7-8a09-765794883524
to MdeModulePkg/Include/Protocol.
They were committed into root directory by mistake at R17657.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17660 6f19259b-4bc3-4df7-8a09-765794883524
And also SMM Ready To Boot.
The SMM Exit Boot Service protocol is to be published by the SMM
Foundation code to associate with EFI_EVENT_GROUP_EXIT_BOOT_SERVICES
to notify SMM driver that system enter exit boot services.
The SMM Legacy Boot protocol is to be published by the SMM
Foundation code to associate with EFI_EVENT_LEGACY_BOOT_GUID
to notify SMM driver that system enter legacy boot.
The SMM Ready To Boot protocol is to be published by the SMM
Foundation code to associate with EFI_EVENT_GROUP_READY_TO_BOOT
to notify SMM driver that system enter ready to boot.
After them, any SMM drivers can get protocol notify on what happened
in DXE phase, then there is no need to let each individual SMM driver
to register SMM Communication Handler for that.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17657 6f19259b-4bc3-4df7-8a09-765794883524
System hangs when RTC time rollover 1999 to 2000
Error processing of GetTime function:
If get time fail,the date/time will display ??,
and update help info to let user know get time fail.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17651 6f19259b-4bc3-4df7-8a09-765794883524
Produce this protocol for each namespace at NVMe controller.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Tian Feng <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17638 6f19259b-4bc3-4df7-8a09-765794883524
Open NVM_EXPRESS_PASS_THRU rather than PCI_IO to create parent-child
relationship.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Tian Feng <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17636 6f19259b-4bc3-4df7-8a09-765794883524
VariableLock in VariableSmmRuntimeDxe.c is installed in EntryPoint now.
It works based on SMM variable handler by SMM communication with
payload buffer. But the payload buffer and SMM variable handler will
be not ready in EntryPoint before SmmVariableReady() call back.
VarCheck in VariableSmmRuntimeDxe.c has the same issue,
so move VarCheck install into SmmVariableReady() also.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17626 6f19259b-4bc3-4df7-8a09-765794883524
Currently, Max Authenticated variable size = Max Regular Variable Size,
and both are controlled via a single PCD:
gEfiMdeModulePkgTokenSpaceGuid.PcdMaxVariableSize.
This PCD is introduced to control the Max Size of Authenticated Variable.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17609 6f19259b-4bc3-4df7-8a09-765794883524
So it could allow platform module to change the serial clock rate per different hardware.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Cc: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17606 6f19259b-4bc3-4df7-8a09-765794883524
The correct logic should be:
- The SectionAlignment is got from Magic number.
- The Magic number is got from PE header and machine type.
The original code mix them.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: "Yao, Jiewen" <Jiewen.yao@intel.com>
Reviewed-by: "Ard Biesheuvel" <ard.biesheuvel@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17603 6f19259b-4bc3-4df7-8a09-765794883524
1. In PiSmmIpl.c, free FullSmramRanges at error condition.
2. Move pool and page management definitions and structures
from PiSmmCorePrivateData.h to PiSmmCore.h.
PiSmmCorePrivateData.h should be only used to share SMM_CORE_PRIVATE_DATA
between PiSmmCore and PiSmmIpl. Pool and page management definitions
and structures were moved from Pool.c and Page.c to PiSmmCorePrivateData.h
incorrectly for memory profile feature at EDK2 R16335 commit.
3. DumpSmramInfo() only used for memory profile, so move the declaration
into SmramProfileRecord.c.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17598 6f19259b-4bc3-4df7-8a09-765794883524
Use if (Image->Started) condition judgement before call to
UnregisterMemoryProfileImage() in CoreUnloadAndCloseImage().
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17597 6f19259b-4bc3-4df7-8a09-765794883524
Display engine base on class opcode to detect whether in
front page.Now remove class/subclass and use FormsetGuid
or ClassGuid to judge whether in front page
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17590 6f19259b-4bc3-4df7-8a09-765794883524
DescEnd will be clipped for alignment in CoreFindFreePagesI, and it
may fall below DescStart, when alignment is more than 16KB (included)
and both DescStart and original DescEnd fall into a single range of
such alignment. This results in a huge size (Negative number in
unsigned type) for this descriptor, fulfilling the allocation
requirement but failing to run ConvertPages; at last it causes
occasional failure of AllocatePages.
A simple comparison is added to ensure we would never get a negative
number.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Heyi Guo <heyi.guo@linaro.org>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17575 6f19259b-4bc3-4df7-8a09-765794883524
1. Continue to get performance data by Performance Protocol
when no SMM performance data found.
2. Not try to get SMM performance data again
if no SMM performance handler found.
3. Correct typo 'totol' and 'guage'.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17561 6f19259b-4bc3-4df7-8a09-765794883524
The initialization of Cc.Iosqes and Cc.Iocqes should not be removed
before any I/O operation as it would impact Qemu-NVMe functionality
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17559 6f19259b-4bc3-4df7-8a09-765794883524
Follow IDE BUS Master spec to ensure the PRDT table not cross 64k
boundary in memory.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17552 6f19259b-4bc3-4df7-8a09-765794883524
For boot performance dump, as current behavior.
It depends on which PerformanceLib instance the DP application linked to.
For example, if DxePerfrmanceLib(MdeModulePkg\Library\DxePerformanceLib)
got linked, it will try to dump PEI and DXE performance data; and if
DxeSmmPerfrmanceLib(MdeModulePkg\Library\DxeSmmPerformanceLib)
got linked, then SMM performance data are expected.
It has burden and confusion to developers about the DP application need to be linked to
different PerformanceLib instance in *.dsc and rebuilt for the performance data dump.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17548 6f19259b-4bc3-4df7-8a09-765794883524
This API can be used for platform to customize the boot description other than using core provided boot description.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17547 6f19259b-4bc3-4df7-8a09-765794883524
The debug message is to print the current TPL and requested TPL value.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17543 6f19259b-4bc3-4df7-8a09-765794883524
Move ACPI default PCDs
gEfiMdeModulePkgTokenSpaceGuid.PcdAcpiDefaultOemId
gEfiMdeModulePkgTokenSpaceGuid.PcdAcpiDefaultOemTableId
gEfiMdeModulePkgTokenSpaceGuid.PcdAcpiDefaultOemRevision
gEfiMdeModulePkgTokenSpaceGuid.PcdAcpiDefaultCreatorId
gEfiMdeModulePkgTokenSpaceGuid.PcdAcpiDefaultCreatorRevision
from [PcdsFixedAtBuild, PcdsPatchableInModule] to
[PcdsFixedAtBuild, PcdsPatchableInModule, PcdsDynamic, PcdsDynamicEx]
to cover some platforms want to update them at boot time.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17542 6f19259b-4bc3-4df7-8a09-765794883524
ARM toolchain raises the build error: "enumerated type mixed with
another type".
To fix the issue, typecase can be used like below.
- return EfiMaxMemoryType + 1;
+ return (EFI_MEMORY_TYPE)(EfiMaxMemoryType + 1);
But to eliminate the confusion, update the return type of
GetProfileMemoryIndex() from EFI_MEMORY_TYPE to UINTN.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17535 6f19259b-4bc3-4df7-8a09-765794883524
ARM toolchain raises the error: "statement is unreachable"
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <Olivier.Martin@arm.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17529 6f19259b-4bc3-4df7-8a09-765794883524
LocatePciExpressCapabilityRegBlock () doesn't check the return status of Pci.Read().
Certain platform's PciRootBridge.Pci.Read() doesn't support PCIE access causing the CapabilityEntry not updated.
If the uninitialized CapabilityEntry equals to a big enough initial value, the while-loop will never end.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Maurice Ma <maurice.ma@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17513 6f19259b-4bc3-4df7-8a09-765794883524
fix bellow bug:
change checkbox from FALSE to TRUE.EFI_BROWSER_ACTION_CHANGED called
but when checkbox change back to FALSE,don't call EFI_BROWSER_ACTION_CHANGED
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17512 6f19259b-4bc3-4df7-8a09-765794883524
A previous incorrect check-in adds the IsaBusDxe driver to <Root>/Bus directory.
The patch fixes it.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17506 6f19259b-4bc3-4df7-8a09-765794883524
This driver follows UEFI driver model and layers on ISA HC protocol defined in PI spec 1.2.1.
It consumes the ISA Host Controller protocol produced by the ISA Host Controller and installs the ISA Host Controller Service Binding protocol on the ISA Host Controller's handle.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17504 6f19259b-4bc3-4df7-8a09-765794883524
The original code hard-codes block size to 512. But after ATA 7 spec,
the non-512 block size is also supported. The code is updated to
dynamically calculate the block size according to IDENTIFY data.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17495 6f19259b-4bc3-4df7-8a09-765794883524
class/subclass is the obseleted key word in VFR file. It is designed in framework HII.
After convert to UEFI HII, it is not used any longer. Now remove them from VFR
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Dandan Bi <dandan.bi@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17493 6f19259b-4bc3-4df7-8a09-765794883524
This change will make DEBUG information be aligned with DEBUG_GCD enabled.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17470 6f19259b-4bc3-4df7-8a09-765794883524
from FullSmramRanges and FullSmramRangeCount in SmmCorePrivate by Constructor.
It can avoid potential first call to FreePool() -> BufferInSmram() ->
if (mSmramRanges == NULL) { GetSmramRanges();} ->
gBS->LocateProtocol() at boottime with >= TPL_NOTIFY or
after ReadyToLock or at OS runtime.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17463 6f19259b-4bc3-4df7-8a09-765794883524
Remove the unused DevicePathSize variable from EnumerateAllKeywords().
Due to our use of -Werror=unused-but-set-variable when building under GCC, the presence of DevicePathSize is breaking the build.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17448 6f19259b-4bc3-4df7-8a09-765794883524
SVN r17428 ("MdeModulePkg: Implement UEFI25 HII Config keyword handler protocol") introduced code that triggers
-Werror=pointer-sign
under gcc ("warn for pointer argument passing or assignment with different signedness"). This patch fix up those locations.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17445 6f19259b-4bc3-4df7-8a09-765794883524
It provides a repository to cache ESRT info for FMP or Non-FMP instance.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Chao Zhang <chao.b.zhang@intel.com>
Reviewed-by: Gao Liming <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17426 6f19259b-4bc3-4df7-8a09-765794883524
When the ExecuteSmmCoreFromSmram() function fails, SmmIplEntry()
restores the SMRAM range to EFI_MEMORY_UC. However, it saves the
return value of gDS->SetMemorySpaceAttributes() in the same Status
variable that gDS->contains the return value of ExecuteSmmCoreFromSmram().
Therefore, if gDS->SetMemorySpaceAttributes() succeeds, the failure
of ExecuteSmmCoreFromSmram() is masked, and Bad Things Happen (TM).
Introduce a temporary variable just for the return value of
gDS->SetMemorySpaceAttributes().
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17417 6f19259b-4bc3-4df7-8a09-765794883524
BaseSortLib is the library instance name not the class name.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17398 6f19259b-4bc3-4df7-8a09-765794883524
Change the code to listen EFI_SW_DXE_BS_PC_LEGACY_BOOT_EVENT instead of the Legacy Boot event to provide more precise performance data.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Ruyu Ni <ruiyu.ni@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17377 6f19259b-4bc3-4df7-8a09-765794883524
It's to follow the PI spec 1.4.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Jie Lin <jie.lin@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17367 6f19259b-4bc3-4df7-8a09-765794883524
PI 1.4 clarified SMM register protocol notify function return status as below:
EFI_SUCCESS Successfully returned the registration record that has
been added or unhooked
EFI_INVALID_PARAMETER Protocol is NULL or Registration is NULL
The implementation of SmmRegisterProtocolNotify() already followed this new
rule, needn't to be updated.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jeff Fan <jeff.fan@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17349 6f19259b-4bc3-4df7-8a09-765794883524
In order to support default value for orderedlist opcode, support buffer type value for default/oneofoption opcode.
If oneofoption used as a default value, it will not be added to normal option list.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Eric Dong <eric.dong@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17336 6f19259b-4bc3-4df7-8a09-765794883524
DriverHealthManagerDxe provides a driver health management VFR form
which will be sent by UefiBootManagerLib when booting a boot option.
It also provides another driver health management VFR form which will
be included by certain boot manager menu through the VFR class GUID.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17331 6f19259b-4bc3-4df7-8a09-765794883524
BootManagerMenuApp only provides a very simple UI showing all the boot options
recorded by "BootOrder" and user can select any of them to boot.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17329 6f19259b-4bc3-4df7-8a09-765794883524
BdsDxe driver links to UefiBootManagerLib and PlatformBootManager to
provide a pure UEFI boot manager conforming to the UEFI spec.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ruiyu Ni <ruiyu.ni@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17328 6f19259b-4bc3-4df7-8a09-765794883524
Boot mode maybe changed at any point during the PEI phase, therefore, boot
mode should be checked later rather at entry point.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17323 6f19259b-4bc3-4df7-8a09-765794883524
This patch produces a EFI_NVM_EXPRESS_PASS_THRU protocol instance
on device handle to provide upper user a way to send cmd to NVMe
device.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17286 6f19259b-4bc3-4df7-8a09-765794883524
The changes in ScsiDisk include:
1. Add UFS disk info support.
2. Remove the wrong block size calculation.
3. Get sense data for TEST_UNIT_READY cmd immediately rather than sending a REQUEST_SENSE cmd again.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17247 6f19259b-4bc3-4df7-8a09-765794883524
It includes 4 drivers:
1. UfsPassThruDxe, which is a UEFI driver and consumes EFI_UFS_HOST_CONTROLLER_PROTOCOL and produces EFI_EXT_SCSI_PASS_THRU_PROTOCOL
2. UfsPciHcDxe, which is specific for pci-based UFS HC implementation and is a UEFI driver to produce EFI_UFS_HOST_CONTROLLER_PROTOCOL.
3. UfsBlockIoPei, which is a PEI driver and consumes EFI_UFS_HOST_CONTROLLER_PPI and produces EFI_PEI_VIRTUAL_BLOCK_IO_PPI.
4. UfsPciHcPei, which is specific for pci-based UFS HC implementation and is a PEI driver to produce EFI_UFS_HOST_CONTROLLER_PPI.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17246 6f19259b-4bc3-4df7-8a09-765794883524
Add stride PCD to MdeModulePkg to support 16550 UARTs with a register stride that is not 1 byte.
The default value is 1 byte.
Quark SoC uses a stride of 4 bytes.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Michael Kinney <michael.d.kinney@intel.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17215 6f19259b-4bc3-4df7-8a09-765794883524
The number of the Prp lists and the number of the entries in last Prp list may be calculated wrongly.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Baban Devkate <baban.devkate@seagate.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17208 6f19259b-4bc3-4df7-8a09-765794883524
Media->IoAlign field of BlockIo protocol instance installed by this driver should be set to the value of ScsiIo->IoAlign.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17195 6f19259b-4bc3-4df7-8a09-765794883524
- SVN r14866:
MdePkg and MdeModulePkg Pcd: Add the new EFI_GET_PCD_INFO_PROTOCOL and
EFI_GET_PCD_INFO_PPI support for PI 1.2.1 compliance.
added the "DataBase" local variable to PcdPeimInit(), and both set it and
used it.
- SVN r14869:
MdeModulePkg and Nt32Pkg Pcd: Add the new EFI_GET_PCD_INFO_PROTOCOL and
EFI_GET_PCD_INFO_PPI support for PI 1.2.1 compliance.
changed the PcdPeimInit() function, but "DataBase" remained both set and
used.
- SVN r17173:
MdeModulePkg Pcd: Check the input SkuId in SetSku()
changed the function again; and this time "DataBase" became
set-but-unused. It triggers the following build error, when building
ArmVirtualizationQemu.dsc with gcc-4.8:
MdeModulePkg/Universal/PCD/Pei/Pcd.c:150:21: error: variable 'DataBase'
set but not used [-Werror=unused-but-set-variable]
PEI_PCD_DATABASE *DataBase;
^
cc1: all warnings being treated as errors
Fix the error by removing the DataBase variable, restoring the pre-r14866
state locally, when the BuildPcdDatabase() function was called, but its
return value was thrown away.
Cc: Star Zeng <star.zeng@intel.com>
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17179 6f19259b-4bc3-4df7-8a09-765794883524
then GetSku() could return the currently active SkuId.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17173 6f19259b-4bc3-4df7-8a09-765794883524
RFC1323 says the most recently received TSVal must be echoed in TSecr in ACK packets
which was not done at first connection because the code saving the TSVal from the peer
was skipped at this point. This resulted in sending an ACK reply with a 0 TSecr that
was rejected at least by FreeBSD. This patch fixes this by updating the saved TSVal
also for connection initiation packets.
Thanks to Laszlo Ersek for analysis and help in debugging.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Fu Siyuan <siyuan.fu@intel.com>
Reviewed-by: Ye Ting <ting.ye@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17165 6f19259b-4bc3-4df7-8a09-765794883524
Also update PCD_SERVICE_PEI_VERSION and PCD_SERVICE_DXE_VERSION to match with
the new PcdDataBase binary generated by BaseTools.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17161 6f19259b-4bc3-4df7-8a09-765794883524
to just return EFI_SUCCESS if the variable has been in the locked list.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17141 6f19259b-4bc3-4df7-8a09-765794883524
Roll back report status code to original place in RuntimeDriverSetVirtualAddressMap.
Per UEFI spec, the call to SetVirtualAddressMap() must be done with the physical mappings.
We can not assume virtual address could work in SetVirtualAddressMap (), so we can not call
report status code interface with virtual address.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Elvin Li <elvin.li@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17139 6f19259b-4bc3-4df7-8a09-765794883524
Move report status code to the end after all pointers convert and image relocation are finished.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Elvin Li <elvin.li@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17136 6f19259b-4bc3-4df7-8a09-765794883524
For PI spec vol3,
"EFI_SW_DXE_BS_PC_VIRTUAL_ADDRESS_CHANGE_EVENT The EVT_SIGNAL_VIRTUAL_ADDRESS_CHANGE event was signaled."
However, in current code base, it is reported before events were signaled.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Elvin Li <elvin.li@intel.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17123 6f19259b-4bc3-4df7-8a09-765794883524
Copy below two library instances from IntelFrameworkModulePkg to MdeModulePkg. Then, Platform dsc can
refer to them from MdeModulePkg, and remove the dependency of IntelFrameworkModulePkg. The ones in
IntelFrameworkModulePkg are still kept for compatibility.
1. PeiDxeDebugLibReportStatusCode
2. LzmaCustomDecompressLib
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17112 6f19259b-4bc3-4df7-8a09-765794883524
Add status code report and cpu deadloop when DXE IPL PPI is not found.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Elvin Li <elvin.li@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17087 6f19259b-4bc3-4df7-8a09-765794883524
PeiCore calls REPORT_STATUS_CODE_WITH_EXTENDED_DATA() with its internal structure for Image
dispatcher. No code consumes it. But, it brings confuse.
DxeCore and SmmCore calls REPORT_STATUS_CODE_WITH_EXTENDED_DATA() with Handle only.
To be consistent, update PeiCore to be same to DxeCore and SmmCore.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17085 6f19259b-4bc3-4df7-8a09-765794883524
to handle the case PE file alignment is not same as PE section alignment.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17063 6f19259b-4bc3-4df7-8a09-765794883524
Add SMBIOS 64-bit entry point and 64-bit table support for SMBIOS 3.0.
Introduce PcdSmbiosEntryPointProvideMethod to produce 32-bit or 64-bit
SMBIOS table.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Elvin Li <elvin.li@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17051 6f19259b-4bc3-4df7-8a09-765794883524
The restriction of UsbHc2.SyncInterruptTransfer() on interrupt transfer direction is removed. This interface could support Interrupt IN/OUT now.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Star Zeng <star.zeng@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17041 6f19259b-4bc3-4df7-8a09-765794883524
to return EFI_NOT_FOUND when a specified variable doesn't exist and
Data parameter is NULL but DataSize parameter is valid in GetVariable() invocation.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17030 6f19259b-4bc3-4df7-8a09-765794883524
On AArch64, the OS can choose to run with a page size of 64 KB,
making it cumbersome to deal with UEFI reserved memory regions
whose boundaries are not 64 KB aligned.
So increase the allocation granularity for runtime regions to
64 KB.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17016 6f19259b-4bc3-4df7-8a09-765794883524
This patch changes the allocation logic for the pool allocator to only
allocate additional pages if the requested allocation cannot be fulfilled
from the current bin or any of the larger ones. If there are larger blocks
available, they will be used to serve the allocation, and the remainder will
be carved up into smaller blocks using the existing carving up logic.
Note that all pool sizes are a multiple of the smallest pool size, so it is
guaranteed that the remainder will be carved up without spilling. Due to the
exponential nature of the pool sizes, the amount of work is logarithmic in
the size of the available block.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17015 6f19259b-4bc3-4df7-8a09-765794883524
In preparation of the next patch, that serves allocations from higher-up
bins if the current bin is depleted, this patch updates the carving up
strategy to populate the largest bins first. To ensure that there will
always be an allocation of the appropriate size made, the current allocation
request is served first from the newly allocated memory region.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17014 6f19259b-4bc3-4df7-8a09-765794883524
In preparation of making the pool code capable of serving allocations
from higher-up bins, update the free path to traverse a candidate page
by following the index of POOL_FREE header instead of duplicating the
carving logic that was used at page allocation time. This allows chunks
to be split into smaller ones, where one can be returned to serve the
allocation, and the other stored in a smaller bin for later use.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17013 6f19259b-4bc3-4df7-8a09-765794883524
The existing linear mapping between allocation size and pool index
does not scale when moving to a 64 KB granularity or beyond. With
a granularity of 64 KB, 2048 (!) bins will be created for each
memory type, each differing 32 bytes in size with the next one.
Instead, introduce an exponential scheme where each bin size is
the sum of the two previous ones.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17012 6f19259b-4bc3-4df7-8a09-765794883524
After fixing the sanity check on the alignment of the runtime regions
in SVN revision #16630 ("MdeModulePkg/DxeMain: Fix wrong sanity check
in CoreTerminateMemoryMap()"), it is no longer possible to define a
runtime allocation alignment that is different from the boot time
allocation alignment.
For instance, #defining the following in MdeModulePkg/Core/Dxe/Mem/Imem.h
will hit the ASSERT () in MdeModulePkg/Core/Dxe/Mem/Page.c:1798
#define EFI_ACPI_RUNTIME_PAGE_ALLOCATION_ALIGNMENT (SIZE_64KB)
#define DEFAULT_PAGE_ALLOCATION (EFI_PAGE_SIZE)
(which is needed for 64-bit ARM to adhere to the Server Base Boot
Requirements [SBBR], which stipulates that all runtime memory regions
should be naturally aligned multiples of 64 KB)
This patch fixes this use case by ensuring that the backing for the memory
pools is allocated in appropriate chunks for the memory type.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@17011 6f19259b-4bc3-4df7-8a09-765794883524
Some compilers requires an empty line at the end of the file.
ARM compiler version 5 is one of these compilers:
error #1-D: last line of file ends without a newline
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
Reviewed-by: Feng Tian <feng.tian@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16918 6f19259b-4bc3-4df7-8a09-765794883524
As the drivers and library do not reference gEfiSmmAccess2ProtocolGuid explicitly now
after SmmMemLib introduced.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16760 6f19259b-4bc3-4df7-8a09-765794883524
Use the example.com domain as recommended in RFC 2606.
NOTE: This does not modify the wording of the "TianoCore Contribution
Agreement 1.0" section
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
Reviewed-by: Bruce Cran <bruce.cran@gmail.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16724 6f19259b-4bc3-4df7-8a09-765794883524
for trying to reclaim variable space at EndOfDxe.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16687 6f19259b-4bc3-4df7-8a09-765794883524
And leave the variable error flag in NV flash as the last boot variable error flag.
After EndOfDxe in InitializeVarErrorFlag (), the variable error flag in NV flash
will be initialized to this local current boot variable error flag.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16684 6f19259b-4bc3-4df7-8a09-765794883524
Modify DxeMain.c which displays incorrect debug message regarding FV Hob.
Specifically, the BaseAddress and Length are not related to the same FV.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Hao Wu <hao.a.wu@intel.com>
Reviewed-by: Liming Gao <liming.gao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16660 6f19259b-4bc3-4df7-8a09-765794883524
The code in AcpiTableDxe handles the installation of FADT and FACS in both
possible orders. In the [FADT, FACS] installation order, the FACS is at
once linked into the FADT. In the [FACS, FADT] installation order, the
FACS is stashed temporarily, and it is linked into the FADT when the FADT
is installed later.
According to the ACPI specification, *at most one* of FADT.FirmwareCtrl
and FADT.XFirmwareCtrl may be nonzero. The code is aware of this
requirement, and it never sets both of them to nonzero values at once.
However, the code doesn't expect the following:
- The caller first installs the FACS, which is stashed. The address that
is saved happens to fall below 4GB.
- The caller then installs a FADT, with a zero FirmwareCtrl field, and a
nonzero (pre-populated) XFirmwareCtrl field.
In this case the code sets FADT.FirmwareCtrl to the less-than-4GB address
of the stashed FACS, and leaves the different nonzero value in
FADT.XFirmwareCtrl. This violates the ACPI specification.
Prevent this by always zeroing the field that we do *not* set.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jiewen Yao <Jiewen.Yao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16659 6f19259b-4bc3-4df7-8a09-765794883524
The function CoreTerminateMemoryMap() performs some final sanity checks on the runtime regions in the memory map before allowing ExitBootServices() to complete.
Unfortunately, it does so by testing the EFI_MEMORY_RUNTIME bit in the Attribute field, which is never set anywhere in the code.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Feng Tian <feng.tian@intel.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16630 6f19259b-4bc3-4df7-8a09-765794883524
Move libraries from ShellPkg into MdeModulePkg and MdePkg.
The following libraries are being migrated out of ShellPkg in order to make
their functionality more widely available.
• PathLib: Incorporate into MdePkg/Library/BaseLib
• FileHandleLib: MdePkg/Library/UefiFileHandleLib
• BaseSortLib: MdeModulePkg/Library/BaseSortLib
• UefiSortLib: MdeModulePkg/Library/UefiSortLib
Diffs showing file changes are in the attached file, LibMigration.patch.
A description of the changes follows:
• Move ShellPkg/Include/Library/FileHandleLib.h to MdePkg/Include/Library/FileHandleLib.h
• Move ShellPkg/Include/Library/SortLib.h to MdeModulePkg/Include/Library/SortLib.h
• Move ShellPkg/Library/BaseSortLib to MdeModulePkg/Library/BaseSortLib
• Move ShellPkg/Library/UefiSortLib to MdeModulePkg/Library/UefiSortLib
• Move ShellPkg/Library/BasePathLib/BasePathLib.c to MdePkg/Library/BaseLib/FilePaths.c
• Merge ShellPkg/Include/Library/PathLib.h into MdePkg/Include/Library/BaseLib.h
• Delete ShellPkg/Library/BasePathLib; Includes BasePathLib.c and BasePathLib.inf
• NetworkPkg/NetworkPkg.dsc
• PerformancePkg.dsc
• OvmfPkg/OvmfPkgX64.dsc
• OvmfPkg/OvmfPkgIa32X64.dsc
• OvmfPkg/OvmfPkgIa32.dsc
o Update SortLib and FileHandleLib library classes to point to the new library locations.
o Remove PathLib library class and make sure that BaseLib is described.
• MdeModulePkg/MdeModulePkg.dec
o Add SortLib library class
• MdePkg/MdePkg.dec
o Add FileHandleLib library class
o Add PcdUefiFileHandleLibPrintBufferSize PCD
• MdePkg/Library/BaseLib/BaseLib.inf
o Add FilePaths.c to [Sources]
• MdePkg/Include/Library/BaseLib.h
o Update file description to include "file path functions"
• ShellPkg/ShellPkg.dsc
o Change PACKAGE_GUID to { C1014BB7-4092-43D4-984F-0738EB424DBF }
o Update PACKAGE_VERSION to 1.0
o Update SortLib and FileHandleLib library classes to point to the new library locations.
o Remove PathLib library class and make sure that BaseLib is described.
o Remove ShellPkg/Library/UefiFileHandleLib/UefiFileHandleLib.inf from [Components]
• ShellPkg/ShellPkg.dec
o Update PLATFORM_VERSION to 1.0
o Remove declarations of the FileHandleLib, SortLib, and PathLib Library Classes
o Update comment for the PcdShellPrintBufferSize PCD.
• ShellPkg/Library/UefiShellLevel2CommandsLib/UefiShellLevel2CommandsLib.inf
• ShellPkg/Application/Shell/Shell.inf
o Remove PathLib from [LibraryClasses]
• ShellPkg/Library/UefiShellLevel2CommandsLib/UefiShellLevel2CommandsLib.h
• ShellPkg/Application/Shell/Shell.h
o Remove #include <Library/PathLib.h>
• ShellPkg/Library/UefiShellLevel1CommandsLib/UefiShellLevel1CommandsLib.inf
o Add PathLib to [LibraryClasses]
• ShellPkg/Library/UefiShellLevel1CommandsLib/If.c
o Remove #include <Library/PathLib.h>
• ShellPkg/Application/ShellSortTestApp/ShellSortTestApp.inf
o Add MdeModulePkg/MdeModulePkg.dec to [Packages]
• MdeModulePkg/Library/BaseSortLib/BaseSortLib.inf
• MdeModulePkg/Library/UefiSortLib/UefiSortLib.inf
o Replace ShellPkg.dec with MdeModulePkg.dec in [Packages]
• MdeModulePkg/Library/UefiSortLib/UefiSortLib.c
o Remove #include <ShellBase.h>
o Define USL_FREE_NON_NULL() to replace SHELL_FREE_NON_NULL()
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Daryl McDaniel <daryl.mcdaniel@intel.com>
Reviewed-by: Jaben Carsey <jaben.carsey@intel.com>
Reviewed-by: Erik Bjorge <erik.c.bjorge@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16601 6f19259b-4bc3-4df7-8a09-765794883524
El Torito format can be used on different media (eg: USB).
A ISO image can be dumped onto a USB mass-storage.
These media might not have the same block size as the CDROM media (ie: 2KB).
The El Torito code and the specification assumes a LBA 2KB.
In addition, the specification says in "12.3.4.4 CD-ROM and DVD-ROM":
UEFI code does not assume a fixed block size.
I was able to dupliacte the issue by copying a debian ISO on a USB driver.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Olivier Martin <olivier.martin@arm.com>
Reviewed-by: Ruiyu Ni <ruiyu.ni@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16600 6f19259b-4bc3-4df7-8a09-765794883524
SPrintLength() and SPrintLengthAsciiFormat() API doesn’t work with 'g', 't' and 'r' option. The fix sync from MdePkg BasePrintLib instance.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Liming Gao <liming.gao@intel.com>
Reviewed-by: Eric Dong <eric.dong@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16593 6f19259b-4bc3-4df7-8a09-765794883524
and follow UEFI spec to check UEFI defined variables.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Star Zeng <star.zeng@intel.com>
Reviewed-by: Jiewen Yao <jiewen.yao@intel.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16579 6f19259b-4bc3-4df7-8a09-765794883524
This module implements Simple FileSystem protocol over Firmware Volume (FV).
EFI Modules included into a FV can be listed and launched from the EFI Shell or any other EFI applications.
Contributed-under: TianoCore Contribution Agreement 1.0
Signed-off-by: Brendan Jackman <brendan.jackman@arm.com>
Signed-off-by: Feng Tian <feng.tian@intel.com>
Reviewed-by: Olivier Martin <olivier.martin@arm.com>
git-svn-id: https://svn.code.sf.net/p/edk2/code/trunk/edk2@16547 6f19259b-4bc3-4df7-8a09-765794883524
