Claudiu reported that on his system S2R cuts off power to the PHY and
after resuming certain PHY settings are lost. The PM folks confirmed
that cutting off power to selected components in S2R is a valid case.
Therefore resuming from S2R, same as from hibernation, has to assume
that the PHY has power-on defaults. As a consequence use the restore
callback also as resume callback.
In addition make sure that the interrupt configuration is restored.
Let's do this in phy_init_hw() and ensure that after this call
actual interrupt configuration is in sync with phydev->interrupts.
Currently, if interrupt was enabled before hibernation, we would
resume with interrupt disabled because that's the power-on default.
This fix applies cleanly only after the commit marked as fixed.
I don't have an affected system, therefore change is compile-tested
only.
[0] https://lore.kernel.org/netdev/1610120754-14331-1-git-send-email-claudiu.beznea@microchip.com/
Fixes: 611d779af7 ("net: phy: fix MDIO bus PM PHY resuming")
Reported-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the moment, PORT_MII is reported in the ethtool ops. This is odd
because it is an interface between the MAC and the PHY and no external
port. Some network card drivers will overwrite the port to twisted pair
or fiber, though. Even worse, the MDI/MDIX setting is only used by
ethtool if the port is twisted pair.
Set the port to PORT_TP by default because most PHY drivers are copper
ones. If there is fibre support and it is enabled, the PHY driver will
set it to PORT_FIBRE.
This will change reporting PORT_MII to either PORT_TP or PORT_FIBRE;
except for the genphy fallback driver.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch to lockdep_assert_held(_once), similar to what is being done
in other subsystems. One advantage is that there's zero runtime
overhead if lockdep support isn't enabled.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/ccc40b9d-8ee0-43a1-5009-2cc95ca79c85@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now that all the PHY drivers have been migrated to directly implement
the generic .handle_interrupt() callback for a seamless support of
shared IRQs and all the .config_inter() implementations clear any
pending interrupts, we can safely remove the two callbacks.
With this patch, phylib has a proper support for shared IRQs (and not
just for multi-PHY devices. A PHY driver must implement both the
.handle_interrupt() and .config_intr() callbacks for the IRQs to be
actually used.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some functions have different names between their prototypes
and the kernel-doc markup.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently we print the driver name twice in phy_attached_print():
- phy_dev_info() prints it as part of the device info
- and we print it as part of the info string
This is a little bit ugly, it makes the info harder to read,
especially if the driver name is a little bit longer.
Therefore omit the driver name (if set) in the info string.
Example from r8169 that uses phylib:
old: Generic FE-GE Realtek PHY r8169-300:00: attached PHY driver \
[Generic FE-GE Realtek PHY] (mii_bus:phy_addr=r8169-300:00, irq=IGNORE)
new: Generic FE-GE Realtek PHY r8169-300:00: attached PHY driver \
(mii_bus:phy_addr=r8169-300:00, irq=IGNORE)
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/8ab72586-f079-41d8-84ee-9f6a5bd97b2a@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It seems there are cases where the interrupts are handled by another
entity (ie an IRQ controller embedded inside the PHY) and do not need
any other interraction from phylib. For this kind of PHYs, like the
RTL8366RB, add the genphy_handle_interrupt_no_ack() function which just
triggers the link state machine.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As a first step into making phylib and all PHY drivers to actually
have support for shared IRQs, make the .ack_interrupt() callback
optional.
After all drivers have been moved to implement the generic
interrupt handle, the phy_drv_supports_irq() check will be
changed again to only require the .handle_interrupts() callback.
Cc: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: Andre Edich <andre.edich@microchip.com>
Cc: Antoine Tenart <atenart@kernel.org>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Divya Koppera <Divya.Koppera@microchip.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Kavya Sree Kotagiri <kavyasree.kotagiri@microchip.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Marco Felsch <m.felsch@pengutronix.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Mathias Kresin <dev@kresin.me>
Cc: Maxim Kochetkov <fido_max@inbox.ru>
Cc: Michael Walle <michael@walle.cc>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Nisar Sayed <Nisar.Sayed@microchip.com>
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Philippe Schenker <philippe.schenker@toradex.com>
Cc: Willy Liu <willy.liu@realtek.com>
Cc: Yuiko Oshino <yuiko.oshino@microchip.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In case of a board which uses a shared IRQ we can easily end up with an
IRQ storm after a forced reboot.
For example, a 'reboot -f' will trigger a call to the .shutdown()
callbacks of all devices. Because phylib does not implement that hook,
the PHY is not quiesced, thus it can very well leave its IRQ enabled.
At the next boot, if that IRQ line is found asserted by the first PHY
driver that uses it, but _before_ the driver that is _actually_ keeping
the shared IRQ asserted is probed, the IRQ is not going to be
acknowledged, thus it will keep being fired preventing the boot process
of the kernel to continue. This is even worse when the second PHY driver
is a module.
To fix this, implement the .shutdown() callback and disable the
interrupts if these are used.
Note that we are still susceptible to IRQ storms if the previous kernel
exited with a panic or if the bootloader left the shared IRQ active, but
there is absolutely nothing we can do about these cases.
Cc: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: Andre Edich <andre.edich@microchip.com>
Cc: Antoine Tenart <atenart@kernel.org>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Divya Koppera <Divya.Koppera@microchip.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Kavya Sree Kotagiri <kavyasree.kotagiri@microchip.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Marco Felsch <m.felsch@pengutronix.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Mathias Kresin <dev@kresin.me>
Cc: Maxim Kochetkov <fido_max@inbox.ru>
Cc: Michael Walle <michael@walle.cc>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Nisar Sayed <Nisar.Sayed@microchip.com>
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Philippe Schenker <philippe.schenker@toradex.com>
Cc: Willy Liu <willy.liu@realtek.com>
Cc: Yuiko Oshino <yuiko.oshino@microchip.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If we have unbound the PHY driver prior to calling phy_detach() (often
via phy_disconnect()) then we can cause a NULL pointer de-reference
accessing the driver owner member. The steps to reproduce are:
echo unimac-mdio-0:01 > /sys/class/net/eth0/phydev/driver/unbind
ip link set eth0 down
Fixes: cafe8df8b9 ("net: phy: Fix lack of reference count on PHY driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the micrel phy driver calls phy_init_hw() as a workaround,
the commit 9886a4dbd2 ("net: phy: call phy_disable_interrupts()
in phy_init_hw()") disables the interrupt unexpectedly. So,
call phy_disable_interrupts() in phy_attach_direct() instead.
Otherwise, the phy cannot link up after the ethernet cable was
disconnected.
Note that other drivers (like at803x.c) also calls phy_init_hw().
So, perhaps, the driver caused a similar issue too.
Fixes: 9886a4dbd2 ("net: phy: call phy_disable_interrupts() in phy_init_hw()")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A recent commit introduced a late error path in phy_device_create()
which fails to release the device name allocated by dev_set_name().
Fixes: 13d0ab6750 ("net: phy: check return code when requesting PHY driver module")
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the patch below, the iteration through the available MMDs is
completely short-circuited, and devs_in_pkg remains set to the initial
value of zero.
Due to devs_in_pkg being zero, the rest of get_phy_c45_ids() is
short-circuited too: the following loop never reaches below this point
either (it executes "continue" for every device in package, failing to
retrieve PHY ID for any of them):
/* Now probe Device Identifiers for each device present. */
for (i = 1; i < num_ids; i++) {
if (!(devs_in_pkg & (1 << i)))
continue;
So c45_ids->device_ids remains populated with zeroes. This causes an
Aquantia AQR412 PHY (same as any C45 PHY would, in fact) to be probed by
the Generic PHY driver.
The issue seems to be a case of submitting partially committed work (and
therefore testing something other than was submitted).
The intention of the patch was to delay exiting the loop until one more
condition is reached (the devs_in_pkg read from hardware is either 0, OR
mostly f's). So fix the patch to reflect that.
Tested with traffic on a LS1028A-QDS, the PHY is now probed correctly
using the Aquantia driver. The devs_in_pkg bit field is set to
0xe000009a, and the MMDs that are present have the following IDs:
[ 5.600772] libphy: get_phy_c45_ids: device_ids[1]=0x3a1b662
[ 5.618781] libphy: get_phy_c45_ids: device_ids[3]=0x3a1b662
[ 5.630797] libphy: get_phy_c45_ids: device_ids[4]=0x3a1b662
[ 5.654535] libphy: get_phy_c45_ids: device_ids[7]=0x3a1b662
[ 5.791723] libphy: get_phy_c45_ids: device_ids[29]=0x3a1b662
[ 5.804050] libphy: get_phy_c45_ids: device_ids[30]=0x3a1b662
[ 5.816375] libphy: get_phy_c45_ids: device_ids[31]=0x0
[ 7.690237] mscc_felix 0000:00:00.5: PHY [0.5:00] driver [Aquantia AQR412] (irq=POLL)
[ 7.704739] mscc_felix 0000:00:00.5: PHY [0.5:01] driver [Aquantia AQR412] (irq=POLL)
[ 7.718918] mscc_felix 0000:00:00.5: PHY [0.5:02] driver [Aquantia AQR412] (irq=POLL)
[ 7.733044] mscc_felix 0000:00:00.5: PHY [0.5:03] driver [Aquantia AQR412] (irq=POLL)
Fixes: bba238ed03 ("net: phy: continue searching for C45 MMDs even if first returned ffff:ffff")
Reported-by: Colin King <colin.king@canonical.com>
Reported-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the time of introduction, in commit bdeced75b1 ("net: dsa: felix:
Add PCS operations for PHYLINK"), support for the Lynx PCS inside Felix
was relying, for USXGMII support, on the fact that get_phy_device() is
able to parse the Lynx PCS "device-in-package" registers for this C45
MDIO device and identify it correctly.
However, this was actually working somewhat by mistake (in the sense
that, even though it was detected, it was detected for the wrong
reasons).
The get_phy_c45_ids() function works by iterating through all MMDs
starting from 1 (MDIO_MMD_PMAPMD) and stops at the first one which
returns a non-zero value in the "device-in-package" register pair,
proceeding to see what that non-zero value is.
For the Felix PCS, the first MMD (1, for the PMA/PMD) returns a non-zero
value of 0xffffffff in the "device-in-package" registers. There is a
code branch which is supposed to treat this case and flag it as wrong,
and normally, this would have caught my attention when adding initial
support for this PCS:
if ((devs_in_pkg & 0x1fffffff) == 0x1fffffff) {
/* If mostly Fs, there is no device there, then let's probe
* MMD 0, as some 10G PHYs have zero Devices In package,
* e.g. Cortina CS4315/CS4340 PHY.
*/
However, this code never actually kicked in, it seems, because this
snippet from get_phy_c45_devs_in_pkg() was basically sabotaging itself,
by returning 0xfffffffe instead of 0xffffffff:
/* Bit 0 doesn't represent a device, it indicates c22 regs presence */
*devices_in_package &= ~BIT(0);
Then the rest of the code just carried on thinking "ok, MMD 1 (PMA/PMD)
says that there are 31 devices in that package, each having a device id
of ffff:ffff, that's perfectly fine, let's go ahead and probe this PHY
device".
But after cleanup commit 320ed3bf90 ("net: phy: split
devices_in_package"), this got "fixed", and now devs_in_pkg is no longer
0xfffffffe, but 0xffffffff. So now, get_phy_device is returning -ENODEV
for the Lynx PCS, because the semantics have remained mostly unchanged:
the loop stops at the first MMD that returns a non-zero value, and that
is MMD 1.
But the Lynx PCS is simply a clause 37 PCS which implements the required
MAC-side functionality for USXGMII (when operated in C45 mode, which is
where C45 devices-in-package detection is relevant to). Of course it
will fail the PMD/PMA test (MMD 1), since it is not a PHY. But it does
implement detection for MDIO_MMD_PCS (3):
- MDIO_DEVS1=0x008a, MDIO_DEVS2=0x0000,
- MDIO_DEVID1=0x0083, MDIO_DEVID2=0xe400
Let get_phy_c45_ids() continue searching for valid MMDs, and don't
assume that every phy_device has a PMA/PMD MMD implemented.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend ethtool_phy_ops to include the 3 function pointers necessary for
implementing PHY statistics. In a subsequent change we will uninline
those functions.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Utilize ethtool_set_ethtool_phy_ops to register a suitable set of PHY
ethtool operations in a dynamic fashion such that ethtool will no longer
directy reference PHY library symbols.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This array is not used outside of phy_device.c, so make it static.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid the W=1 warning that symbol 'genphy_c45_driver' was not
declared. Should it be static?
Declare it on the phy header file.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we only call phy_device_reset() if the PHY driver implements
the probe() callback. This is not mandatory and many drivers (e.g.
realtek) don't need probe() for most devices but still can have reset
GPIOs defined. There's no reason to depend on the presence of probe()
here so pull the reset code out of the if clause.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Keeping the headers in alphabetical order is better for readability and
allows to easily see if given header is already included.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor overlapping changes in xfrm_device.c, between the double
ESP trailing bug fix setting the XFRM_INIT flag and the changes
in net-next preparing for bonding encryption support.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper function that will return the index in the array for the
passed in internal delay value. The helper requires the array, size and
delay value.
The helper will then return the index for the exact match or return the
index for the index to the closest smaller value.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call phy_disable_interrupts() in phy_init_hw() to "have a defined init
state as we don't know in which state the PHY is if the PHY driver is
loaded. We shouldn't assume that it's the chip power-on defaults, BIOS
or boot loader could have changed this. Or in case of dual-boot
systems the other OS could leave the PHY in whatever state." as pointed
out by Heiner.
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expand the device_ids[] array to allow all MMD IDs to be read rather
than just the first 8 MMDs, but only read the ID if the MDIO_STAT2
register reports that a device really is present here for these new
devices to maintain compatibility with our current behaviour. Note
that only a limited number of devices have MDIO_STAT2.
88X3310 PHY vendor MMDs do are marked as present in the
devices_in_package, but do not contain IEE 802.3 compatible register
sets in their lower space. This avoids reading incorrect values as MMD
identifiers.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have two competing requirements for the devices_in_package field.
We want to use it as a bit array indicating which MMDs are present, but
we also want to know if the Clause 22 registers are present.
Since "devices in package" is a term used in the 802.3 specification,
keep this as the as-specified values read from the PHY, and introduce
a new member "mmds_present" to indicate which MMDs are actually
present in the PHY, derived from the "devices in package" value.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only set the devices_in_package to a non-zero value if we find a valid
value for this field, so we avoid leaving it set to e.g. 0x1fffffff.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for probing MMDs above 7 for a valid devices-in-package
specifier, but only probe the vendor MMDs for this if they also report
that there the device is present in status register 2. This avoids
issues where the MMD is implemented, but does not provide IEEE 802.3
compliant registers (such as the MV88X3310 PHY.)
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reword the get_phy_device() kerneldoc to be more explicit about how
we probe for the PHY, and what the various return conditions signify.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the ID check from get_phy_device() into get_phy_c22_id(), which
simplifies get_phy_device(). The ID reading functions are now
responsible for indicating whether they found a PHY or not via their
return code - they must return -ENODEV when a PHY is not present.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we decide that a PHY is not present, we do not need to go through
the hoops of setting *phy_id to 0xffffffff, and then return zero to
make get_phy_device() fail - we can return -ENODEV which will have the
same effect.
Doing so means we no longer have to pass a pointer to phy_id in, and
we can then clean up the clause 22 path in a similar way.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rearrange the code to read the PHY IDs, so we don't call get_phy_id()
only to immediately call get_phy_c45_ids(). Move that logic into
get_phy_device(), which results in better readability.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the Cortina PHY workaround out of the "devices in package" loop;
it doesn't need to be in there as the control flow will terminate the
loop once we enter the workaround irrespective of the workaround's
outcome. The workaround is triggered by the ID being mostly 1's, which
will in any case terminate the loop.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 02a6efcab6 ("net: phy: allow scanning busses with missing
phys") added a special condition to return -ENODEV in case -ENODEV or
-EIO was returned from the first read of the MII_PHYSID1 register.
In case the MDIO bus data line pull-up is not strong enough, the MDIO
bus controller will not flag this as a read error. This can happen when
a pluggable daughter card is not connected and weak internal pull-ups
are used (since that is the only option, otherwise the pins are
floating).
The second read of MII_PHYSID2 will be correctly flagged an error
though, but now we will return -EIO which will be treated as a hard
error, thus preventing MDIO bus scanning loops to continue succesfully.
Apply the same logic to both register reads, thus allowing the scanning
logic to proceed.
Fixes: 02a6efcab6 ("net: phy: allow scanning busses with missing phys")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a recurring pattern throughout some of the PHY code converting
a devad and regnum to our packed clause 45 representation. Rather than
having this scattered around the code, let's put a common translation
function in mdio.h, and provide some register accessors.
Convert the phylib core, phylink, bcm87xx and cortina to use these.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MSCC bug fix in 'net' had to be slightly adjusted because the
register accesses are done slightly differently in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
This function was introduced to allow for different handling of
link up and link down events particularly with regard to the
netif_carrier. The third argument do_carrier allowed the flag to
be left unchanged.
Since then the phylink has introduced an implementation that
completely ignores the third parameter since it never wants to
change the flag and the phylib always sets the third parameter
to true so the flag is always changed.
Therefore the third argument (i.e. do_carrier) is no longer
necessary and can be removed. This also means that the phylib
phy_link_down() function no longer needs its second argument.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The compilation warning below reveals that the errors returned from
the sfp_bus_add_upstream() call are not propagated to the callers.
Fix it by returning "ret".
14:37:51 drivers/net/phy/phy_device.c: In function 'phy_sfp_probe':
14:37:51 drivers/net/phy/phy_device.c:1236:6: warning: variable 'ret'
set but not used [-Wunused-but-set-variable]
14:37:51 1236 | int ret;
14:37:51 | ^~~
Fixes: 298e54fa81 ("net: phy: add core phylib sfp support")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The unsigned variable val is being checked for an error by checking
if it is less than zero. This can never occur because val is unsigned.
Fix this by making val a plain int.
Addresses-Coverity: ("Unsigned compared against zero")
Fixes: bdbdac7649 ("ethtool: provide UAPI for PHY master/slave configuration.")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This UAPI is needed for BroadR-Reach 100BASE-T1 devices. Due to lack of
auto-negotiation support, we needed to be able to configure the
MASTER-SLAVE role of the port manually or from an application in user
space.
The same UAPI can be used for 1000BASE-T or MultiGBASE-T devices to
force MASTER or SLAVE role. See IEEE 802.3-2018:
22.2.4.3.7 MASTER-SLAVE control register (Register 9)
22.2.4.3.8 MASTER-SLAVE status register (Register 10)
40.5.2 MASTER-SLAVE configuration resolution
45.2.1.185.1 MASTER-SLAVE config value (1.2100.14)
45.2.7.10 MultiGBASE-T AN control 1 register (Register 7.32)
The MASTER-SLAVE role affects the clock configuration:
-------------------------------------------------------------------------------
When the PHY is configured as MASTER, the PMA Transmit function shall
source TX_TCLK from a local clock source. When configured as SLAVE, the
PMA Transmit function shall source TX_TCLK from the clock recovered from
data stream provided by MASTER.
iMX6Q KSZ9031 XXX
------\ /-----------\ /------------\
| | | | |
MAC |<----RGMII----->| PHY Slave |<------>| PHY Master |
|<--- 125 MHz ---+-<------/ | | \ |
------/ \-----------/ \------------/
^
\-TX_TCLK
-------------------------------------------------------------------------------
Since some clock or link related issues are only reproducible in a
specific MASTER-SLAVE-role, MAC and PHY configuration, it is beneficial
to provide generic (not 100BASE-T1 specific) interface to the user space
for configuration flexibility and trouble shooting.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are packages which contain multiple PHY devices, eg. a quad PHY
transceiver. Provide functions to allocate and free shared storage.
Usually, a quad PHY contains global registers, which don't belong to any
PHY. Provide convenience functions to access these registers.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a soft reset is triggered whilst PHY is in power-down, then
phydev->suspended will remain set. Seems we didn't face any issue yet
caused by this, but better reset the suspended flag after soft reset.
See also the following from 22.2.4.1.1
Resetting a PHY is accomplished by setting bit 0.15 to a logic one.
This action shall set the status and control registers to their default
states.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since 6e2d85ec05 ("net: phy: Stop with excessive soft reset")
we don't need genphy_no_soft_reset() any longer. Not setting
callback soft_reset results in a no-op now.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gently handle the case that phy_suspend() is called whilst PHY is in
power-down.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far we set phydev->suspended to true in phy_suspend() even if the
PHY driver doesn't implement the suspend callback. This applies
accordingly for the resume path. The current behavior doesn't cause
any issue I'd be aware of, but it's not logical and misleading,
especially considering the description of the flag:
"suspended: Set to true if this phy has been suspended successfully"
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we have scenarios like
mdiobus_register()
-> loads PHY driver module(s)
-> registers PHY driver(s)
-> may schedule async probe
phydev = mdiobus_get_phy()
<phydev action involving PHY driver>
or
phydev = phy_device_create()
-> loads PHY driver module
-> registers PHY driver
-> may schedule async probe
<phydev action involving PHY driver>
then we expect the PHY driver to be bound to the phydev when triggering
the action. This may not be the case in case of asynchronous probing.
Therefore ensure that PHY drivers are probed synchronously.
Default still is sync probing, except async probing is explicitly
requested. I saw some comments that the intention is to promote
async probing for more parallelism in boot process and want to be
prepared for the case that the default is changed to async probing.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
use phy_read_poll_timeout() to replace the poll codes for
simplify the code in phy_poll_reset() function.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far we have the unfortunate situation that mdio_bus_phy_may_suspend()
is called in suspend AND resume path, assuming that function result is
the same. After the original change this is no longer the case,
resulting in broken resume as reported by Geert.
To fix this call mdio_bus_phy_may_suspend() in the suspend path only,
and let the phy_device store the info whether it was suspended by
MDIO bus PM.
Fixes: 503ba7c696 ("net: phy: Avoid multiple suspends")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mptcp conflict was overlapping additions.
The SMC conflict was an additional and removal happening at the same
time.
Signed-off-by: David S. Miller <davem@davemloft.net>
When auto-negotiation is not required, return value should be zero.
Changes v1->v2:
- improved comments and code as Andrew Lunn and Heiner Kallweit suggestion
- fixed issue in genphy_c45_check_and_restart_aneg as Russell King
suggestion.
Fixes: 2a10ab043a ("net: phy: add genphy_check_and_restart_aneg()")
Fixes: 1af9f16840 ("net: phy: add genphy_c45_check_and_restart_aneg()")
Signed-off-by: Sudheesh Mavila <sudheesh.mavila@amd.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is currently possible for a PHY device to be suspended as part of a
network device driver's suspend call while it is still being attached to
that net_device, either via phy_suspend() or implicitly via phy_stop().
Later on, when the MDIO bus controller get suspended, we would attempt
to suspend again the PHY because it is still attached to a network
device.
This is both a waste of time and creates an opportunity for improper
clock/power management bugs to creep in.
Fixes: 803dd9c77a ("net: phy: avoid suspending twice a PHY")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 93c0970493 ("net: phy: consider latched link-down status in
polling mode") removed double-read of latched link-state register for
polling mode from genphy_update_link(). This added extra ~1s delay into
sequence link down->up.
Following scenario:
- After boot link goes up
- phy_start() is called triggering an aneg restart, hence link goes
down and link-down info is latched.
- After aneg has finished link goes up. In phy_state_machine is checked
link state but it is latched "link is down". The state machine is
scheduled after one second and there is detected "link is up". This
extra delay can be avoided when we keep link-state register double read
in case when link was down previously.
With this solution we don't miss a link-down event in polling mode and
link-up is faster.
Details about this quirky behavior on Realtek phy:
Without patch:
T0: aneg is started, link goes down, link-down status is latched
T0+3s: state machine runs, up-to-date link-down is read
T0+4s: state machine runs, aneg is finished (BMSR_ANEGCOMPLETE==1),
here i read link-down (BMSR_LSTATUS==0),
T0+5s: state machine runs, aneg is finished (BMSR_ANEGCOMPLETE==1),
up-to-date link-up is read (BMSR_LSTATUS==1),
phydev->link goes up, state change PHY_NOLINK to PHY_RUNNING
With patch:
T0: aneg is started, link goes down, link-down status is latched
T0+3s: state machine runs, up-to-date link-down is read
T0+4s: state machine runs, aneg is finished (BMSR_ANEGCOMPLETE==1),
first BMSR read: BMSR_ANEGCOMPLETE==1 and BMSR_LSTATUS==0,
second BMSR read: BMSR_ANEGCOMPLETE==1 and BMSR_LSTATUS==1,
phydev->link goes up, state change PHY_NOLINK to PHY_RUNNING
Signed-off-by: Petr Oros <poros@redhat.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a linkmode helper to set the flow control advertisement in an
ethtool linkmode mask according to the tx/rx capabilities. This
implementation is moved from phylib, and documented with an
analysis of its shortcomings.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a couple of helpers to resolve negotiated flow control. Two helpers
are provided:
- linkmode_resolve_pause() which takes the link partner and local
advertisements, and decodes whether we should enable TX or RX pause
at the MAC. This is useful outside of phylib, e.g. in phylink.
- phy_get_pause(), which returns the TX/RX enablement status for the
current negotiation results of the PHY.
This allows us to centralise the flow control resolution, rather than
spreading it around.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The information about the PHY attached to the PHYLINK instance is useful
but is missing the IRQ prints that phy_attached_info() adds.
phy_attached_info() is a bit long and it would not be possible to use
phylink_info() anyway.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When parsing a PHY node, register its time stamper, if any, and attach
the instance to the PHY device.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the stack supports time stamping in PHY devices. However,
there are newer, non-PHY devices that can snoop an MII bus and provide
time stamps. In order to support such devices, this patch introduces
a new interface to be used by both PHY and non-PHY devices.
In addition, the one and only user of the old PHY time stamping API is
converted to the new interface.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY IDs are 32-bit unsigned quantities. Ensure that they are always
treated as such, and not passed around as "int"s.
Fixes: 13d0ab6750 ("net: phy: check return code when requesting PHY driver module")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two drivers and generic code which contain exactly the same
code to read the status of a PHY operating without autonegotiation
enabled. Rather than duplicate this code, provide a helper to read
this information.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper for restarting autonegotiation(), similar to the clause 45
variant. Use it in __genphy_config_aneg()
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove initialisers that set .aneg_done to genphy_aneg_done - this is
the default for clause 22 PHYs, so the initialiser is redundant.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a phydev is created, the speed and duplex are set to zero and
-1 respectively, rather than using the predefined SPEED_UNKNOWN and
DUPLEX_UNKNOWN constants.
There is a window at initialisation time where we may report link
down using the 0/-1 values. Tidy this up and use the predefined
constants, so debug doesn't complain with:
"Unsupported (update phy-core.c)/Unsupported (update phy-core.c)"
when the speed and duplex settings are printed.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
We currently match clause 45 PHYs using any ID read from a MMD marked
as present in the "Devices in package" registers 5 and 6. However,
this is incorrect. 45.2 says:
"The definition of the term package is vendor specific and could be
a chip, module, or other similar entity."
so a package could be more or less than the whole PHY - a PHY could be
made up of several modules instantiated onto a single chip such as the
Marvell 88x3310, or some of the MMDs could be disabled according to
chip configuration, such as the Broadcom 84881.
In the case of Broadcom 84881, the "Devices in package" registers
contain 0xc000009b, meaning that there is a PHYXS present in the
package, but all registers in MMD 4 return 0xffff. This leads to our
matching code incorrectly binding this PHY to one of our generic PHY
drivers.
This patch changes the way we determine whether to attempt to match a
MMD identifier, or use it to request a module - if the identifier is
all-ones, then we skip over it. When reading the identifiers, we
initialise phydev->c45_ids.device_ids to all-ones, only reading the
device ID if the "Devices in package" registers indicates we should.
This avoids the generic drivers incorrectly matching on a PHY ID of
0xffffffff.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add core phylib help for supporting SFP sockets on PHYs. This provides
a mechanism to inform the SFP layer about PHY up/down events, and also
unregister the SFP bus when the PHY is going away.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for clause 37 1000Base-X auto-negotiation.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Tao Ren <taoren@fb.com>
Tested-by: René van Dorst <opensource@vdorst.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify the assignment to OR when dealing with phydev->dev_flags in
phy_attach_direct function, and this is to make sure dev_flags set in
driver's probe callback won't be lost.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
CC: Heiner Kallweit <hkallweit1@gmail.com>
CC: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Tao Ren <taoren@fb.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers just call phy_ethtool_ksettings_set() to set the
links, for those phy drivers that use genphy_read_status(), if
autoneg is on, and the link is up, than execute "ethtool -s
ethx autoneg on" will cause "link partner" information disappear.
The call trace is phy_ethtool_ksettings_set()->phy_start_aneg()
->linkmode_zero(phydev->lp_advertising)->genphy_read_status(),
the link didn't change, so genphy_read_status() just return, and
phydev->lp_advertising is zero now.
This patch moves the clear operation of lp_advertising from
phy_start_aneg() to genphy_read_lpa()/genphy_c45_read_lpa(), and
if autoneg on and autoneg not complete, just clear what the
generic functions care about.
Fixes: 88d6272aca ("net: phy: avoid unneeded MDIO reads in genphy_read_status")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move reading the link partner advertisement out of genphy_read_status()
into its own separate function. This will allow re-use of this code by
PHY drivers that are able to read the resolved status from the PHY.
Tested-by: tinywrkb <tinywrkb@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that all users have been removed we can remove genphy_config_init.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Value of MII_CTRL1000 is needed only if LPA_1000MSFAIL is set.
Therefore move reading this register.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After configuring and restarting aneg we immediately try to read the
link status. On some systems the PHY may not yet have cleared the
"aneg complete" and "link up" bits, resulting in a false link-up
signal. See [0] for a report.
Clause 22 and 45 both require the PHY to keep the AN_RESTART
bit set until the PHY actually starts auto-negotiation.
Let's consider this in the generic functions for reading link status.
The commit marked as fixed is the first one where the patch applies
cleanly.
[0] https://marc.info/?t=156518400300003&r=1&w=2
Fixes: c1164bb1a6 ("net: phy: check PMAPMD link status only in genphy_c45_read_link")
Tested-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
The integrated PHY in 2.5Gbps chip RTL8125 is the first (known to me)
PHY that uses standard Clause 22 for all modes up to 1Gbps and adds
2.5Gbps control using vendor-specific registers. To use phylib for
the standard part little extensions are needed:
- Move most of genphy_config_aneg to a new function
__genphy_config_aneg that takes a parameter whether restarting
auto-negotiation is needed (depending on whether content of
vendor-specific advertisement register changed).
- Don't clear phydev->lp_advertising in genphy_read_status so that
we can set non-C22 mode flags before.
Basically both changes mimic the behavior of the equivalent Clause 45
functions.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using linkmode_adv_to_mii_adv_t and linkmode_adv_to_mii_ctrl1000_t
allows to simplify the code. In addition avoiding the conversion to
the legacy u32 advertisement format allows to remove the warning.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In phy_start_aneg() autoneg is started, and immediately after that
link and autoneg status are read. As reported in [0] it can happen that
at time of this read the PHY has reset the "aneg complete" bit but not
yet the "link up" bit, what can result in a false link-up detection.
To fix this don't report link as up if we're in aneg mode and PHY
doesn't signal "aneg complete".
[0] https://marc.info/?t=156413509900003&r=1&w=2
Fixes: 4950c2ba49 ("net: phy: fix autoneg mismatch case in genphy_read_status")
Reported-by: liuyonglong <liuyonglong@huawei.com>
Tested-by: liuyonglong <liuyonglong@huawei.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variables phy_basic_ports_array, phy_fibre_port_array and
phy_all_ports_features_array are declared static and marked
EXPORT_SYMBOL_GPL(), which is at best an odd combination.
Because the variables were decided to be a part of API, this commit
removes the static attributes and adds the declarations to the header.
Fixes: 3c1bcc8614 ("net: ethernet: Convert phydev advertize and supported from u32 to link mode")
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit "net: phy: Add detection of 1000BaseX link mode support" added
support for not filtering out 1000BaseX mode from the PHY's supported
modes in genphy_config_init, but we have to make a similar change in
genphy_read_abilities in order to actually detect it as a supported mode
in the first place. Add this in.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add 1000BaseX to the link modes which are detected based on the
MII_ESTATUS register as per 802.3 Clause 22. This allows PHYs which
support 1000BaseX to work properly with drivers using phylink.
Previously 1000BaseX support was not detected, and if that was the only
mode the PHY indicated support for, phylink would refuse to attach it
due to the list of supported modes being empty.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is a step towards allowing PHY drivers to handle more
interrupt sources than just link change. E.g. several PHY's have
built-in temperature monitoring and can raise an interrupt if a
temperature threshold is exceeded. We may be interested in such
interrupts also if the phylib state machine isn't started.
Therefore move enabling interrupts to phy_request_interrupt().
v2:
- patch added to series
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export a phy_standalone device attribute that is meant to give the
indication that this PHY lacks an attached_dev and its corresponding
sysfs link. The attribute will be created only when the
phy_attach_direct() function will be called with a NULL net_device.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In general, we don't want MAC drivers calling phy_attach_direct with the
net_device being NULL. Add checks against this in all the functions
calling it: phy_attach() and phy_connect_direct().
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A prerequisite for PHYLIB to work in the absence of a struct net_device
is to not access pointers to it.
Changes are needed in the following areas:
- Printing: In some places netdev_err was replaced with phydev_err.
- Incrementing reference count to the parent MDIO bus driver: If there
is no net device, then the reference count should definitely be
incremented since there is no chance that it was an Ethernet driver
who registered the MDIO bus.
- Sysfs links are not created in case there is no attached_dev.
- No netif_carrier_off is done if there is no attached_dev.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a cosmetic patch that wraps the operation of creating sysfs
links between the netdev->phydev and the phydev->attached_dev.
This is needed to keep the indentation level in check in a follow-up
patch where this function will be guarded against the existence of a
phydev->attached_dev.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that there is a link mode for 100BaseT1, use it in
phy_basic_t1_features so T1 PHY drivers will indicate this mode via
the Ethtool API.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have valid scenarios where ETHTOOL_LINK_MODE_Pause_BIT doesn't
need to be supported. Therefore extend the first check to check
for rx_pause being set.
See also phy_set_asym_pause:
rx=0 and tx=1: advertise asym pause only
rx=0 and tx=0: stop advertising both pause modes
The fixed commit isn't wrong, it's just the one that introduced the
linkmode bitmaps.
Fixes: 3c1bcc8614 ("net: ethernet: Convert phydev advertize and supported from u32 to link mode")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When probing the phy device we set sym and asym pause in the "supported"
bitmap (unless the PHY tells us otherwise). However we don't know yet
whether the MAC supports pause. Simply copying phy->supported to
phy->advertising will trigger advertising pause, and that's not
what we want. Therefore add phy_advertise_supported() that copies all
modes but doesn't touch the pause bits.
In phy_support_(a)sym_pause we shouldn't set any bits in the supported
bitmap because we may set a bit the PHY intentionally disabled.
Effective pause support should be the AND-combined PHY and MAC pause
capabilities. If the MAC supports everything, then it's only relevant
what the PHY supports. If MAC supports sym pause only, then we have to
clear the asym bit in phydev->supported.
Copy the pause flags only and don't touch the modes, because a driver
may have intentionally removed a mode from phydev->advertising.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Considering that in polling mode each link drop will be latched,
settings can't have changed if link was up and is up.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY's behave differently when being reset. Some reset registers to
defaults, some don't. Some trigger an autoneg restart, some don't.
So let's also set the autoneg restart bit when resetting. Then PHY
behavior should be more consistent. Clearing BMCR_ISOLATE serves the
same purpose and is borrowed from genphy_restart_aneg.
BMCR holds the speed / duplex settings in fixed mode. Therefore
we may have an issue if a soft reset resets BMCR to its default.
So better call genphy_setup_forced() afterwards in fixed mode.
We've seen no related complaint in the last >10 yrs, so let's
treat it as an improvement.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In phy_device_create() we set phydev->autoneg = 1. This isn't changed
even if the PHY doesn't support autoneg. This seems to affect very
few PHY's, and they disable phydev->autoneg in their config_init
callback. So it's more of an improvement, therefore net-next.
The patch also wouldn't apply to older kernel versions because the
link mode bitmaps have been introduced recently.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original patch didn't set phydev->autoneg_complete in one exit path.
Fix this.
Fixes: 4950c2ba49 ("net: phy: fix autoneg mismatch case in genphy_read_status")
Reported-by: Simon Horman <horms@verge.net.au>
Tested-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently a number of generic functions for Clause 45 PHY's has been
added. So let's replace the old very limited genphy_10g_driver with a
genphy_c45_driver. This driver isn't limited to 10G, however it's worth
to be noted that Clause 45 doesn't cover 1000Base-T. For using
1000Base-T with a Clause 45 PHY a dedicated PHY driver using vendor
registers is needed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
genphy_read_status() so far checks phydev->supported, not the actual
PHY capabilities. This can make a difference if the supported speeds
have been limited by of_set_phy_supported() or phy_set_max_speed().
It seems that this issue only affects the link partner advertisements
as displayed by ethtool. Also this patch wouldn't apply to older
kernels because linkmode bitmaps have been introduced recently.
Therefore net-next.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Meanwhile we have generic functions for reading the abilities of
Clause 22 / 45 PHY's. This allows to use them as fallback in case
callback get_features isn't set. Benefit is the reduction of
boilerplate code in PHY drivers.
v2:
- adjust the comment in phy_driver_register to match the code
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original patch didn't consider the case that autoneg process
finishes successfully but both link partners have no mode in common.
In this case there's no link, nevertheless we may be interested in
what the link partner advertised.
Like phydev->link we set phydev->autoneg_complete in
genphy_update_link() and use the stored value in genphy_read_status().
This way we don't have to read register BMSR again.
Fixes: b6163f194c ("net: phy: improve genphy_read_status")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the genphy driver populates phydev->supported like this:
First all possible feature bits are set, then genphy_config_init()
reads the available features from the chip and remove all unsupported
features from phydev->supported. This can be simplified by using
genphy_read_abilities().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to genphy_c45_pma_read_abilities() add a function to dynamically
detect the abilities of a Clause 22 PHY. This is mainly copied from
genphy_config_init().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch improves few aspects of genphy_read_status():
- Don't initialize lpagb, it's not needed.
- Move initializing phydev->speed et al before the if clause.
- In auto-neg case, skip populating lp_advertising if we
don't have a link. This avoids quite some unnecessary
MDIO reads in case of phylib polling mode.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far we effectively clear the BMCR register. Some PHY's can deal
with this (e.g. because they reset BMCR to a default as part of a
soft-reset) whilst on others this causes issues because e.g. the
autoneg bit is cleared. Marvell is an example, see also thread [0].
So let's be a little bit more gentle and leave all bits we're not
interested in as-is. This change is needed for PHY drivers to
properly deal with the original patch.
[0] https://marc.info/?t=155264050700001&r=1&w=2
Fixes: 6e2d85ec05 ("net: phy: Stop with excessive soft reset")
Tested-by: Phil Reid <preid@electromag.com.au>
Tested-by: liweihang <liweihang@hisilicon.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to use this function in phy-c45.c too, therefore export it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If link partner and we can't agree on any mode, then it doesn't make
sense to pretend we would have agreed on 10/half. Therefore set a
proper default.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After recent changes to genphy_read_status() this orphaned register
read remained as leftover. So remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have phy_resolve_aneg_linkmode() we can make
genphy_read_status() much simpler.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since of_set_phy_supported was moved to phy-core.c, we can also move
of_set_phy_eee_broken to the same location, so that we have all OF
functions in the same place.
This patch doesn't intend to introduce any change in behaviour.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When setting a PHY's max speed using either the max-speed DT property
or ethtool, we should mask-out all non-compatible modes according to the
settings table, instead of just the 10/100BASET modes.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Suggested-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new function phy_modify_mmd_changed(), the result speaks for itself.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use phy_modify_changed() to simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for runtime determination of what the PHY supports, by
adding a new function to the phy driver. The get_features call should
set the phydev->supported member with the features the PHY supports.
It is only called if phydrv->features is NULL.
This requires minor changes to pause. The PHY driver should not set
pause abilities, except for when it has odd cause capabilities, e.g.
pause cannot be disabled. With this change, phydev->supported already
contains the drivers abilities, including pause. So rather than
considering phydrv->features, look at the phydev->supported, and
enable pause if neither of the pause bits are already set.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
[hkallweit1@gmail.com: fixed small checkpatch complaint in one comment]
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We will soon support asking the PHY at runtime to determine what
features it supports, rather than forcing it to be compile time.
But we should probe the PHY first. So probe the phy driver earlier.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY registers are only 16 bits wide, therefore, if the read was
successful, there's no need to mask out the higher 16 bits.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bit 0 in register 1.5 doesn't represent a device but is a flag that
Clause 22 registers are present. Therefore disregard this bit when
populating the device list. If code needs this information it
should read register 1.5 directly instead of accessing the device
list.
Because this bit doesn't represent a device don't define a
MDIO_MMD_XYZ constant, just define a MDIO_DEVS_XYZ constant for
the flag in the device list bitmap.
v2:
- make masking of bit 0 more explicit
- improve commit message
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link status register latches link-down events. Therefore, if link
is reported as being up, there's no need for a second read.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link status value latches link-down events. To get the current
status we read the register twice in genphy_update_link(). There's
a potential risk that we miss a link-down event in polling mode.
This may cause issues if the user e.g. connects his machine to a
different network.
On the other hand reading the latched value may cause issues in
interrupt mode. Following scenario:
- After boot link goes up
- phy_start() is called triggering an aneg restart, hence link goes
down and link-down info is latched.
- After aneg has finished link goes up and triggers an interrupt.
Interrupt handler reads link status, means it reads the latched
"link is down" info. But there won't be another interrupt as long
as link stays up, therefore phylib will never recognize that link
is up.
Deal with both scenarios by reading the register twice in interrupt
mode only.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we enable the interrupts in phy_start() we don't have to do it
before. Therefore remove enabling interrupts from phy_start_interrupts()
and rename this function to reflect the changed functionality.
v2:
- improve warning to clearly state that we fall back to polling
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The state machine is a no-op before phy_start() has been called.
Therefore let's enable it in phy_start() only. In phy_start()
let's call phy_start_machine() instead of phy_trigger_machine().
phy_start_machine is an alias for phy_trigger_machine but it makes
clearer that we start the state machine here instead of just
triggering a run.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Where the license text and the MODULE_LICENSE() value agree, convert
to using an SPDX header, removing the license text.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the soft reset (if defined) is done only if the driver also
implements the config_init callback. I think this dependency is a
mistake, so let's remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was reported that on a system with nfsboot and w/o initramfs network
fails because trying to load the PHY driver returns -ENOENT. Reason was
that due to missing initramfs the modprobe binary isn't available.
So we have to ignore error code -ENOENT.
Fixes: 13d0ab6750 ("net: phy: check return code when requesting PHY driver module")
Reported-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since phy driver features became a link_mode bitmap, phy drivers that
don't have a list of features configured will cause the kernel to crash
when probed.
Prevent the phy driver from registering if the features field is missing.
Fixes: 719655a149 ("net: phy: Replace phy driver features u32 with link_mode bitmap")
Reported-by: Scott Wood <oss@buserror.net>
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Interrupts have been disabled in phy_stop() already. So we can remove
phy_stop_interrupts() and free the interrupt in phy_disconnect()
directly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The call to the phylib state machine in phy_stop() just ensures that
the state machine isn't re-triggered, but a state machine call may
be scheduled already. So lets's call phy_stop_machine().
This also allows to get rid of the call to phy_stop_machine() in
phy_disconnect().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stop PHY if needed when entering phy_disconnect. This allows drivers
that don't need a separate call to phy_stop() to omit this call.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only caller of get_phy_id() is get_phy_device(). There a PHY ID of
0xffffffff is translated back to -ENODEV. So we can avoid some
overhead by returning -ENODEV directly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When requesting the PHY driver module fails we'll bind the genphy
driver later. This isn't obvious to the user and may cause, depending
on the PHY, different types of issues. Therefore check the return code
of request_module(). Note that we only check for failures in loading
the module, not whether a module exists for the respective PHY ID.
v2:
- add comment explaining what is checked and what is not
- return error from phy_device_create() if loading module fails
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are already checking in phy_detach() that the PHY driver is of
generic kind (1G or 10G) and we are going to make use of that in the SFP
layer as well for 1000BaseT SFP modules, so expose helper functions to
return that information.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no need to and one shouldn't include asm/irq.h directly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some time ago phydev_info() and friends have been added. They allow to
improve and simplify logging.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This workaround attempt helped for some but not all affected users.
With commit 11287b693d ("r8169: load Realtek PHY driver module
before r8169") we have a better workaround now, so we an remove
the first attempt.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bcm87xx and micrel driver has PHYs which are missing the .features
value. Add them. The bcm87xx is a 10G FEC only PHY. Add the needed
features definition of this PHY.
Fixes: 719655a149 ("net: phy: Replace phy driver features u32 with link_mode bitmap")
Reported-by: Scott Wood <oss@buserror.net>
Reported-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lots of conflicts, by happily all cases of overlapping
changes, parallel adds, things of that nature.
Thanks to Stephen Rothwell, Saeed Mahameed, and others
for their guidance in these resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
Even though the link is down before entering hibernation,
there is an issue that the network interface always links up after resuming
from hibernation.
If the link is still down before enabling the network interface,
and after resuming from hibernation, the phydev->state is forcibly set
to PHY_UP in mdio_bus_phy_restore(), and the link becomes up.
In suspend sequence, only if the PHY is attached, mdio_bus_phy_suspend()
calls phy_stop_machine(), and mdio_bus_phy_resume() calls
phy_start_machine().
In resume sequence, it's enough to do the same as mdio_bus_phy_resume()
because the state has been preserved.
This patch fixes the issue by calling phy_start_machine() in
mdio_bus_phy_restore() in the same way as mdio_bus_phy_resume().
Fixes: bc87922ff5 ("phy: Move PHY PM operations into phy_device")
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
3c1bcc8614 ("net: ethernet: Convert phydev advertize and supported
from u32 to link mode") left some unused code in phy_probe(), remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a _mod_ variant of mii_lpa_to_linkmode_lpa_t. Use this to fix the
genphy_read_status() where the 1G link partner features are getting
lost.
Fixes: c0ec3c2736 ("net: phy: Convert u32 phydev->lp_advertising to linkmode")
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename mii_stat1000_to_linkmode_lpa_t to
mii_stat1000_mod_linkmode_lpa_t to indicate it modifies the passed
linkmode bitmap, without clearing any other bits.
Add a helper to set/clear bits in a linkmode.
Use this helper to ensure bit are clear which the stat1000 indicates
should not be set.
Fixes: c0ec3c2736 ("net: phy: Convert u32 phydev->lp_advertising to linkmode")
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts:
ef1b5bf506 ("net: phy: Fix not to call phy_resume() if PHY is not attached")
8c85f4b812 ("net: phy: micrel: add toggling phy reset if PHY is not attached")
Andrew Lunn informs me that there are alternative efforts
underway to fix this more properly.
Signed-off-by: David S. Miller <davem@davemloft.net>
Logic of phy_device_create() requests PHY modules according to PHY ID
but for C45 PHYs we use different field for the IDs.
Let's also request the modules for these IDs.
Changes from v1:
- Only request C22 modules if C45 are not present (Andrew)
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Joao Pinto <joao.pinto@synopsys.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes an issue that mdio_bus_phy_resume() doesn't call
phy_resume() if the PHY is not attached.
Fixes: 803dd9c77a ("net: phy: avoid suspending twice a PHY")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently __set_phy_supported allows to add modes w/o checking whether
the PHY supports them. This is wrong, it should never add modes but
only remove modes we don't want to support.
The commit marked as fixed didn't do anything wrong, it just copied
existing functionality to the helper which is being fixed now.
Fixes: f3a6bd393c ("phylib: Add phy_set_max_speed helper")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently __set_phy_supported allows to add modes w/o checking whether
the PHY supports them. This is wrong, it should never add modes but
only remove modes we don't want to support.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial conflict in net/core/filter.c, a locally computed
'sdif' is now an argument to the function.
Signed-off-by: David S. Miller <davem@davemloft.net>
After switching the r8169 driver to use phylib some user reported that
their network is broken. This was caused by the genphy PHY driver being
used instead of the dedicated PHY driver for the RTL8211B. Users
reported that loading the Realtek PHY driver module upfront fixes the
issue. See also this mail thread:
https://marc.info/?t=154279781800003&r=1&w=2
The issue is quite weird and the root cause seems to be somewhere in
the base driver core. The patch works around the issue and may be
removed once the actual issue is fixed.
The Fixes tag refers to the first reported occurrence of the issue.
The issue itself may have been existing much longer and it may affect
users of other network chips as well. Users typically will recognize
this issue only if their PHY stops working when being used with the
genphy driver.
Fixes: f1e911d5d0 ("r8169: add basic phylib support")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the icplus driver has been fixed all PHY drivers supporting
interrupts have both callbacks (config_intr and ack_interrupt)
implemented - as it should be. Therefore phy_drv_supports_irq()
can be changed now to check for both callbacks being implemented.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert phy drivers to report the link partner advertised modes using
a linkmode bitmap. This allows them to report the higher speeds which
don't fit in a u32.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a few MAC/PHYs combinations which now support > 1Gbps. These
may need to make use of link modes with bits > 31. Thus their
supported PHY features or advertised features cannot be implemented
using the current bitmap in a u32. Convert to using a linkmode bitmap,
which can support all the currently devices link modes, and is future
proof as more modes are added.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using phy_mac_interrupt() the irq number is set to
PHY_IGNORE_INTERRUPT, therefore phy_interrupt_is_valid() returns false.
As a result phy_change() effectively just calls phy_trigger_machine()
when called from phy_mac_interrupt() via phy_change_work(). So we can
call phy_trigger_machine() from phy_mac_interrupt() directly and
remove some now unneeded code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flag PHY_HAS_INTERRUPT is used only here for this small check. I think
using interrupts isn't possible if a driver defines neither
config_intr nor ack_interrupts callback. So we can replace checking
flag PHY_HAS_INTERRUPT with checking for these callbacks.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When indicating the MAC supports Symmetric Pause, clear the Asymmetric
Pause bit, which could of been already set is the PHY supports it.
Reported-by: Labbe Corentin <clabbe@baylibre.com>
Fixes: c306ad3618 ("net: ethernet: Add helper for MACs which support pause")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor conflict in net/core/rtnetlink.c, David Ahern's bug fix in 'net'
overlapped the renaming of a netlink attribute in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
This is one step in allowing phylib to make use of link_mode bitmaps,
instead of u32 for supported and advertised features. Convert the phy
drivers to use bitmaps to indicates the features they support.
Build bitmap equivalents of the u32 values at runtime, and have the
drivers point to the appropriate bitmap. These bitmaps are shared, and
we don't want a driver to modify them. So mark them __ro_after_init.
Within phylib, the features bitmap is currently turned back into a
u32. This will be removed once the whole of phylib, and the drivers
are converted to use bitmaps.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add phydev_info() and make use of it within the phy drivers and core
code.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Core of the problem is that phy_suspend() suspends the PHY when it
should not because of WoL. phy_suspend() checks for WoL already, but
this works only if the PHY driver handles WoL (what is rarely the case).
Typically WoL is handled by the MAC driver.
This patch uses new member wol_enabled of struct net_device as
additional criteria in the check when not to suspend the PHY because
of WoL.
Last but not least change phy_detach() to call phy_suspend() before
attached_dev is set to NULL. phy_suspend() accesses attached_dev
when checking whether the MAC driver activated WoL.
Fixes: f1e911d5d0 ("r8169: add basic phylib support")
Fixes: e8cfd9d6c7 ("net: phy: call state machine synchronously in phy_stop")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Actually there's nothing wrong with the two changes marked as "Fixes",
they just revealed a problem which has been existing before.
After having switched r8169 to phylib it was reported that WoL from
shutdown doesn't work any longer (WoL from suspend isn't affected).
Reason is that during shutdown phy_disconnect()->phy_detach()->
phy_suspend() is called.
A similar issue occurs when the phylib state machine calls
phy_suspend() when handling state PHY_HALTED.
Core of the problem is that phy_suspend() suspends the PHY when it
should not due to WoL. phy_suspend() checks for WoL already, but this
works only if the PHY driver handles WoL (what is rarely the case).
Typically WoL is handled by the MAC driver.
phylib knows about this and handles it in mdio_bus_phy_may_suspend(),
but that's used only when suspending the system, not in other cases
like shutdown.
Therefore factor out the relevant check from
mdio_bus_phy_may_suspend() to a new function phy_may_suspend() and
use it in phy_suspend().
Last but not least change phy_detach() to call phy_suspend() before
attached_dev is set to NULL. phy_suspend() accesses attached_dev
when checking whether the MAC driver activated WoL.
Fixes: f1e911d5d0 ("r8169: add basic phylib support")
Fixes: e8cfd9d6c7 ("net: phy: call state machine synchronously in phy_stop")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While consolidating the PHY reset in phy_init_hw() an unconditionaly
BMCR soft-reset I became quite trigger happy with those. This was later
on deactivated for the Generic PHY driver on the premise that a prior
software entity (e.g: bootloader) might have applied workarounds in
commit 0878fff1f4 ("net: phy: Do not perform software reset for
Generic PHY").
Since we have a hook to wire-up a soft_reset callback, just use that and
get rid of the call to genphy_soft_reset() entirely. This speeds up
initialization and link establishment for most PHYs out there that do
not require a reset.
Fixes: 87aa9f9c61 ("net: phy: consolidate PHY reset in phy_init_hw()")
Tested-by: Wang, Dongsheng <dongsheng.wang@hxt-semitech.com>
Tested-by: Chris Healy <cphealy@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than have MAC drivers open code the test, add a helper in
phylib. This will help when we change the type of phydev->supported.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool can be used to enable/disable pause. Add a helper to configure
the PHY when Pause is supported.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool can be used to enable/disable pause. Add a helper to configure
the PHY when asym pause is supported.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than have the MAC drivers manipulate phydev members, add a
helper function for MACs supporting Pause, but not Asym Pause.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than have the MAC drivers manipulate phydev members to indicate
they support Asym Pause, add a helper function.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some MAC hardware cannot support a subset of link modes. e.g. often
1Gbps Full duplex is supported, but Half duplex is not. Add a helper
to remove such a link mode.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Certain PHY's have issues when operating in GBit slave mode and can
be forced to master mode. Examples are RTL8211C, also the Micrel PHY
driver has a DT setting to force master mode.
If two such chips are link partners the autonegotiation will fail.
Standard defines a self-clearing on read, latched-high bit to
indicate this error. Check this bit to inform the user.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently also the pause flags are removed from phydev->supported because
they're not included in PHY_DEFAULT_FEATURES. I don't think this is
intended, especially when considering that this function can be called
via phy_set_max_speed() anywhere in a driver. Change the masking to mask
out only the values we're going to change. In addition remove the
misleading comment, job of this small function is just to adjust the
supported and advertised speeds.
Fixes: f3a6bd393c ("phylib: Add phy_set_max_speed helper")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A PHY is a type of MDIO device, so let's model it as struct device_type
and place PM ops, attribute groups and release callback on device type
level. For this the attribute definitions have to be moved.
This change allows us to get rid of the PM ops on a bus level in a second
step.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some MDIO busses will error out when trying to read a phy address with no
phy present at that address. In that case, probing the bus will fail
because __mdiobus_register() is scanning the bus for all possible phys
addresses.
In case MII_PHYSID1 returns -EIO or -ENODEV, consider there is no phy at
this address and set the phy ID to 0xffffffff which is then properly
handled in get_phy_device().
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fun set of conflict resolutions here...
For the mac80211 stuff, these were fortunately just parallel
adds. Trivially resolved.
In drivers/net/phy/phy.c we had a bug fix in 'net' that moved the
function phy_disable_interrupts() earlier in the file, whilst in
'net-next' the phy_error() call from this function was removed.
In net/ipv4/xfrm4_policy.c, David Ahern's changes to remove the
'rt_table_id' member of rtable collided with a bug fix in 'net' that
added a new struct member "rt_mtu_locked" which needs to be copied
over here.
The mlxsw driver conflict consisted of net-next separating
the span code and definitions into separate files, whilst
a 'net' bug fix made some changes to that moved code.
The mlx5 infiniband conflict resolution was quite non-trivial,
the RDMA tree's merge commit was used as a guide here, and
here are their notes:
====================
Due to bug fixes found by the syzkaller bot and taken into the for-rc
branch after development for the 4.17 merge window had already started
being taken into the for-next branch, there were fairly non-trivial
merge issues that would need to be resolved between the for-rc branch
and the for-next branch. This merge resolves those conflicts and
provides a unified base upon which ongoing development for 4.17 can
be based.
Conflicts:
drivers/infiniband/hw/mlx5/main.c - Commit 42cea83f95
(IB/mlx5: Fix cleanup order on unload) added to for-rc and
commit b5ca15ad7e (IB/mlx5: Add proper representors support)
add as part of the devel cycle both needed to modify the
init/de-init functions used by mlx5. To support the new
representors, the new functions added by the cleanup patch
needed to be made non-static, and the init/de-init list
added by the representors patch needed to be modified to
match the init/de-init list changes made by the cleanup
patch.
Updates:
drivers/infiniband/hw/mlx5/mlx5_ib.h - Update function
prototypes added by representors patch to reflect new function
names as changed by cleanup patch
drivers/infiniband/hw/mlx5/ib_rep.c - Update init/de-init
stage list to match new order from cleanup patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
For some phy devices, even though they don't support the MMD extended
register access, it does have some side effect if we are trying to
read/write the MMD registers via indirect method. So introduce general
dummy stubs for MMD register access which these devices can use to avoid
such side effect.
Fixes: b6b5e8a691 ("gianfar: Disable EEE autoneg by default")
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some ethernet drivers (like TI CPSW) may connect and manage >1 Net PHYs per
one netdevice, as result such drivers will produce warning during system
boot and fail to connect second phy to netdevice when PHYLIB framework
will try to create sysfs link netdev->phydev for second PHY
in phy_attach_direct(), because sysfs link with the same name has been
created already for the first PHY. As result, second CPSW external
port will became unusable.
Fix it by relaxing error checking when PHYLIB framework is creating sysfs
link netdev->phydev in phy_attach_direct(), suppressing warning by using
sysfs_create_link_nowarn() and adding error message instead.
After this change links (phy->netdev and netdev->phy) creation failure is not
fatal any more and system can continue working, which fixes TI CPSW issue.
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Fixes: a399546049 ("net: phy: Relax error checking on sysfs_create_link()")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the link state is initialized to "up" when the phy_device is
being created. This is not consistent with the phy state being
initialized to PHY_DOWN.
Usually this doen't do any harm because the link state is updated
once the PHY reaches state PHY_AN. However e.g. if a LAN port isn't
used and the PHY remains down this inconsistency remains and calls
to functions like phy_print_status() give false results.
Therefore change the initialization to link being down.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit f5e64032a7 ("net: phy: fix resume handling") changes the
locking semantics for phy_resume() such that the caller now needs to
hold the phy mutex. Not all call sites were adopted to this new
semantic, resulting in warnings from the added
WARN_ON(!mutex_is_locked(&phydev->lock)). Rather than change the
semantics, add a __phy_resume() and restore the old behavior of
phy_resume().
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>
Fixes: f5e64032a7 ("net: phy: fix resume handling")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When forcing a specific link mode, the PHY driver must clear the
existing speed and duplex bits in BMCR while preserving some other
control bits. This logic was accidentally inverted with the introduction
of phy_modify().
Fixes: fea23fb591 ("net: phy: convert read-modify-write to phy_modify()")
Signed-off-by: Ingo van Lil <inguin@gmx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new helpers phy_set_bits / phy_clear_bits in phylib.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mask argument for phy_modify() in several locations was inverted.
Fixes: fea23fb591 ("net: phy: convert read-modify-write to phy_modify()")
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert read-modify-write sequences in at803x, Marvell and core phylib
to use phy_modify() to ensure safety.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Three sets of overlapping changes, two in the packet scheduler
and one in the meson-gxl PHY driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
When a PHY has the BMCR_PDOWN bit set, it may decide to ignore writes
to other registers, or reset the registers to power-on defaults.
Micrel PHYs do this for their interrupt registers.
The current structure of phylib tries to enable interrupts before
resuming (and releasing) the BMCR_PDOWN bit. This fails, causing
Micrel PHYs to stop working after a suspend/resume sequence if they
are using interrupts.
Fix this by ensuring that the PHY driver resume methods do not take
the phydev->lock mutex themselves, but the callers of phy_resume()
take that lock. This then allows us to move the call to phy_resume()
before we enable interrupts in phy_start().
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some PHYs need the refclk to be a continuous clock. Therefore they don't
allow turning it off and on again during operation. Nonetheless such a
clock switching is performed by some ETH drivers (namely FEC [1]) for
power saving reasons. An example for an affected PHY is the
SMSC/Microchip LAN8720 in "REF_CLK In Mode".
In order to provide a uniform method to overcome this problem this patch
adds a new phy_driver flag (PHY_RST_AFTER_CLK_EN) and corresponding
function phy_reset_after_clk_enable() to the phylib. These should be
used to trigger reset of the PHY after the refclk is switched on again.
[1] commit e8fcfcd568 ("net: fec: optimize the clock management to save power")
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY devices sometimes do have their reset signal (maybe even power
supply?) tied to some GPIO and sometimes it also does happen that a boot
loader does not leave it deasserted. So far this issue has been attacked
from (as I believe) a wrong angle: by teaching the MAC driver to manipulate
the GPIO in question; that solution, when applied to the device trees, led
to adding the PHY reset GPIO properties to the MAC device node, with one
exception: Cadence MACB driver which could handle the "reset-gpios" prop
in a PHY device subnode. I believe that the correct approach is to teach
the 'phylib' to get the MDIO device reset GPIO from the device tree node
corresponding to this device -- which this patch is doing...
Note that I had to modify the AT803x PHY driver as it would stop working
otherwise -- it made use of the reset GPIO for its own purposes...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Rob Herring <robh@kernel.org>
[geert: Propagate actual errors from fwnode_get_named_gpiod()]
[geert: Avoid destroying initial setup]
[geert: Consolidate GPIO descriptor acquiring code]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove generic settings for callbacks config_aneg and read_status
from drivers.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Given NR_IRQS is 2048 on sparc64, and even 32784 on alpha, 3 digits is
not enough to represent interrupt numbers on all architectures. Hence
PHY interrupt numbers may be truncated during printing.
Increase the buffer size from 4 to 8 bytes to fix this.
Fixes: 5e369aefdc ("net: stmmac: Delete dead code for MDIO registration")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This code is no longer used, the logging function was changed by commit
fbca164776 ("net: stmmac: Use the right logging function in stmmac_mdio_register").
It was previously showing information about the type of the IRQ, if it's
polled, ignored or a normal interrupt. As we don't want information loss,
I have moved this code to phy_attached_print().
Fixes: fbca164776 ("net: stmmac: Use the right logging function in stmmac_mdio_register")
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link between the ethernet MAC and its PHY has become more complex
as the interface evolves. This is especially true with serdes links,
where the part of the PHY is effectively integrated into the MAC.
Serdes links can be connected to a variety of devices, including SFF
modules soldered down onto the board with the MAC, a SFP cage with
a hotpluggable SFP module which may contain a PHY or directly modulate
the serdes signals onto optical media with or without a PHY, or even
a classical PHY connection.
Moreover, the negotiation information on serdes links comes in two
varieties - SGMII mode, where the PHY provides its speed/duplex/flow
control information to the MAC, and 1000base-X mode where both ends
exchange their abilities and each resolve the link capabilities.
This means we need a more flexible means to support these arrangements,
particularly with the hotpluggable nature of SFP, where the PHY can
be attached or detached after the network device has been brought up.
Ethtool information can come from multiple sources:
- we may have a PHY operating in either SGMII or 1000base-X mode, in
which case we take ethtool/mii data directly from the PHY.
- we may have a optical SFP module without a PHY, with the MAC
operating in 1000base-X mode - the ethtool/mii data needs to come
from the MAC.
- we may have a copper SFP module with a PHY whic can't be accessed,
which means we need to take ethtool/mii data from the MAC.
Phylink aims to solve this by providing an intermediary between the
MAC and PHY, providing a safe way for PHYs to be hotplugged, and
allowing a SFP driver to reconfigure the serdes connection.
Phylink also takes over support of fixed link connections, where the
speed/duplex/flow control are fixed, but link status may be controlled
by a GPIO signal. By avoiding the fixed-phy implementation, phylink
can provide a faster response to link events: fixed-phy has to wait for
phylib to operate its state machine, which can take several seconds.
In comparison, phylink takes milliseconds.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- remove sync status
- rework supported and advertisment handling
- add 1000base-x speed for fixed links
- use functionality exported from phy-core, reworking
__phylink_ethtool_ksettings_set for it
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes, we need to do additional work between the PHY coming up and
marking the carrier present - for example, we may need to wait for the
PHY to MAC link to finish negotiation. This changes phylib to provide
a notification function pointer which avoids the built-in
netif_carrier_on() and netif_carrier_off() functions.
Standard ->adjust_link functionality is provided by hooking a helper
into the new ->phy_link_change method.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add set_loopback in phy_driver, which is used by MAC
driver to enable or disable phy loopback. it also add a generic
genphy_loopback function, which use BMCR loopback bit to enable
or disable loopback.
Signed-off-by: Lin Yun Sheng <linyunsheng@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the old 10G genphy support to sit beside the new clause 45 library
functions, so all the 10G phy code is together.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add generic helpers for 802.3 clause 45 PHYs for >= 10Gbps support.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some Ethernet drivers will attach/connect to a PHY device before calling
register_netdevice() which is responsible for calling netdev_register_kobject()
which would do the network device's kobject initialization. In such a case,
sysfs_create_link() would return -ENOENT because the network device's kobject
is not ready yet, and we would fail to connect to the PHY device.
In order to keep things simple and symetrical, we just take the success path as
indicative of the ability to access the network device's kobject, and create
the second link if that's the case.
Fixes: 5568363f0c ("net: phy: Create sysfs reciprocal links for attached_dev/phydev")
Reported-by: Woojung Hung <Woojung.Huh@microchip.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is currently no way for a program scanning /sys to know whether a
network device is attached to a particular PHY device, just like the PHY
device is not pointed back to its attached network device.
Create a symbolic link in the network device's namespace named "phydev"
which points to the PHY device and create a symbolic link in the PHY
device's namespace named "attached_dev" that points back to the network
device. These links are set up during phy_attach_direct() and removed
during phy_detach() for symetry.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit af6b6967d6 ("net: phy: export genphy_config_init()") introduced
this EXPORT_SYMBOL and put it after gen10g_soft_reset() instead of
directly after genphy_config_init. Probably this happend when the patch
was applied because http://patchwork.ozlabs.org/patch/339622/ looks ok.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch everyone over to using phy_read_mmd() and phy_write_mmd() now
that they are able to handle both Clause 22 indirect addressing and
Clause 45 direct addressing methods to the MMD registers.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Generic PHY driver is a catch-all PHY driver and it should preserve
whatever prior initialization has been done by boot loader or firmware
agents. For specific PHY device configuration it is expected that a
specialized PHY driver would take over that role.
Resetting the generic PHY was a bad idea that has lead to several
complaints and downstream workarounds e.g: in OpenWrt/LEDE so restore
the behavior prior to 87aa9f9c61 ("net: phy: consolidate PHY
reset in phy_init_hw()").
Reported-by: Felix Fietkau <nbd@nbd.name>
Fixes: 87aa9f9c61 ("net: phy: consolidate PHY reset in phy_init_hw()")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are number of function calls, originating from user-space,
typically through the Ethernet driver that can make us crash by
dereferencing phydev->drv which will be NULL once we unbind the driver
from the PHY.
There are still functional issues that prevent an unbind then rebind to
work, but these will be addressed separately.
Suggested-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY library does not deal very well with bind and unbind events. The first
thing we would see is that we were not properly canceling the PHY state machine
workqueue, so we would be crashing while dereferencing phydev->drv since there
is no driver attached anymore.
Suggested-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Generic PHY drivers gets assigned after we checked that the current
PHY driver is NULL, so we need to check a few things before we can
safely dereference d->driver. This would be causing a NULL deference to
occur when a system binds to the Generic PHY driver. Update
phy_attach_direct() to do the following:
- grab the driver module reference after we have assigned the Generic
PHY drivers accordingly, and remember we came from the generic PHY
path
- update the error path to clean up the module reference in case the
Generic PHY probe function fails
- split the error path involving phy_detacht() to avoid double free/put
since phy_detach() does all the clean up
- finally, have phy_detach() drop the module reference count before we
call device_release_driver() for the Generic PHY driver case
Fixes: cafe8df8b9 ("net: phy: Fix lack of reference count on PHY driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patches regarding eee-broken-modes was merged before all people
involved could find an agreement on the best way to move forward.
While we agreed on having a DT property to mark particular modes as broken,
the value used for eee-broken-modes mapped the phy register in very direct
way. Because of this, the concern is that it could be used to implement
configuration policies instead of describing a broken HW.
In the end, having a boolean property for each mode seems to be preferred
over one bit field value mapping the register (too) directly.
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
