This reverts commit 3bc6a37f59.
Commit 3bc6a37f59 ("drm/vc4: hdmi: Fix HSM clock too low on Pi4") was
introduced to work around an issue partly due to the clk-bcm2835 driver
on the RaspberryPi0-3.
Since we're not using that driver for our HDMI clocks, we can now revert
that inelegant solution.
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://lore.kernel.org/r/20230126-rpi-display-fw-clk-cleanup-v1-3-d646ff6fb842@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
On the RaspberryPi0-3, the HSM clock was provided by the clk-bcm2835
driver, but on the Pi4 it was provided by the firmware through the
clk-raspberrypi driver.
The clk-bcm2835 driver registers the HSM clock using the
CLK_SET_RATE_GATE flag that prevents any modification to the rate while
the clock is active.
This meant that we needed to call clk_set_min_rate() before our call to
pm_runtime_resume_and_get() since our runtime_resume implementation
needs to enable the HSM clock for the HDMI controller registers to be
functional.
However, the HSM clock is part of the HDMI power domain which might not
be powered prior to the pm_runtime_resume_and_get() call, so we could
end up changing the rate of the HSM clock while its power domain was
disabled.
We recently changed the backing driver for the RaspberryPi0-3 to
clk-raspberrypi though, which doesn't have such restrictions. We can
thus move the clk_set_min_rate() after our call to runtime_resume and
avoid the access while the power domain is disabled.
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://lore.kernel.org/r/20230126-rpi-display-fw-clk-cleanup-v1-2-d646ff6fb842@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The 120MHz value hardcoded in the call to max_t to compute the HSM rate
is defined in the driver as HSM_MIN_CLOCK_FREQ, let's switch to it so
that it's more readable.
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://lore.kernel.org/r/20230126-rpi-display-fw-clk-cleanup-v1-1-d646ff6fb842@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Issue is some displays go blank at the point of firmware to kms
handover. Plugging/unplugging hdmi cable, power cycling display, or
switching standby off/on
typically resolve this case.
Finally managed to find a display that suffers from this, and track down
the issue.
The firmware uses AVMUTE in normal operation. It will set AVMUTE before
disabling hdmi clocks and phy. It will clear AVMUTE after clocks and phy
are set up for a new hdmi mode.
But with the hdmi handover from firmware to kms, AVMUTE will be set by
firmware.
kms driver typically has no GCP packet (except for deep colour modes).
The spec isn't clear on whether to consider the AVMUTE as continuing
indefinitely in the absence of a GCP packet, or to consider that state
to have ended.
Most displays behave as we want, but there are a number (from multiple
manufacturers) which need to see AVMUTE cleared before displaying a
picture.
Lets just always enable GCP packet with AVMUTE cleared. That resolves
the issue on problematic displays.
From HDMI 1.4 spec:
A CD field of zero (Color Depth not indicated) shall be used whenever
the Sink does not indicate support for Deep Color. This value may
also be used in Deep Color mode to transmit a GCP indicating only
non-Deep Color information (e.g. AVMUTE).
So use CD=0 where we were previously not enabling a GCP.
Link: https://forum.libreelec.tv/thread/24780-le-10-0-1-rpi4-no-picture-after-update-from-le-10-0-0
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20230127161219.457058-1-maxime@cerno.tech
The bcm2711 has two HDMI outputs, each with their own CEC adapter.
The CEC adapter name has to be unique, but it is currently
hardcoded to "vc4" for both outputs. Change this to use the card_name
from the variant information in order to make the adapter name unique.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: 15b4511a4a ("drm/vc4: add HDMI CEC support")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/dcf1db75-d9cc-62cc-fa12-baf1b2b3bf31@xs4all.nl
The back porch timings were correct, only the sync offset was wrong.
Correct timing is now reported for 1080i and 576i, but the h offset is
incorrect for 480i for non-obvious reasons.
Fixes: fb10dc451c ("drm/vc4: hdmi: Correct HDMI timing registers for interlaced modes")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20221207-rpi-hvs-crtc-misc-v1-14-1f8e0770798b@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Currently, vc4 has its own debugfs infrastructure that adds the debugfs
files on drm_dev_register(). With the introduction of the new debugfs,
functions, replace the vc4 debugfs structure with the DRM debugfs
device-centered function, drm_debugfs_add_file().
Moreover, remove the explicit error handling of debugfs related functions,
considering that the only failure mode is -ENOMEM and also that error
handling is not recommended for debugfs functions, as pointed out in [1].
[1] https://lore.kernel.org/all/YWAmZdRwnAt6wh9B@kroah.com/
Signed-off-by: Maíra Canal <mcanal@igalia.com>
Reviewed-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Melissa Wen <mwen@igalia.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Maíra Canal <mairacanal@riseup.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20221219120621.15086-5-mcanal@igalia.com
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmN6wAgeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG0EYH/3/RO90NbrFItraN
Lzr+d3VdbGjTu8xd1M+PRTmwh3zxLpB+Jwqr0T0A2gzL9B/D+AUPUJdrCVbv9DqS
FLJAVqoeV20dNBAHSffOOLPsgCZ+Eu+LzlNN7Iqde0e8cyZICFMNktitui84Xm/i
1NgFVgz9OZ6+aieYvUj3FrFq0p8GTIaC/oybDZrxYKcO8ZzKVMJ11swRw10wwq0g
qOOECvV3w7wlQ8upQZkzFxItKFc7EexZI6R4elXeGSJJ9Hlc092dv/zsKB9dwV+k
WcwkJrZRoezYXzgGBFxUcQtzi+ethjrPjuJuM1rYLUSIcfIW/0lkaSLgRoBu8D+I
1GfXkXs=
=gt6P
-----END PGP SIGNATURE-----
Backmerge tag 'v6.1-rc6' into drm-next
Linux 6.1-rc6
This is needed for drm-misc-next and tegra.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Commit 6bed2ea3cb ("drm/vc4: hdmi: Reset link on hotplug") introduced
the vc4_hdmi_reset_link() function. This function dereferences the
"connector" pointer before checking whether it is NULL or not.
Rework variable assignment to avoid this issue.
Fixes: 6bed2ea3cb ("drm/vc4: hdmi: Reset link on hotplug")
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Link: https://lore.kernel.org/r/20221110134752.238820-3-jose.exposito89@gmail.com
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Simplify vc4_hdmi_supports_scrambling() by changing its first parameter
from struct drm_encoder to struct vc4_hdmi.
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Link: https://lore.kernel.org/r/20221110134752.238820-2-jose.exposito89@gmail.com
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
UAPI Changes:
Cross-subsystem Changes:
- dma-buf: locking improvements
- firmware: New API in the RaspberryPi firmware driver used by vc4
Core Changes:
- client: Null pointer dereference fix in drm_client_buffer_delete()
- mm/buddy: Add back random seed log
- ttm: Convert ttm_resource to use size_t for its size, fix for an
undefined behaviour
Driver Changes:
- bridge:
- adv7511: use dev_err_probe
- it6505: Fix return value check of pm_runtime_get_sync
- panel:
- sitronix: Fixes and clean-ups
- lcdif: Increase DMA burst size
- rockchip: runtime_pm improvements
- vc4: Fix for a regression preventing the use of 4k @ 60Hz, and
further HDMI rate constraints check.
- vmwgfx: Cursor improvements
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCY2N8/gAKCRDj7w1vZxhR
xT1TAQDiwdSyL/bzOk/WYggmj5wmFqb2PPFbFRt/DOTLl52ZdwEAmtE9I2WKvY8w
sxZYF9gfFnQC3id7YwNs+CDb1kAangc=
=6GBd
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2022-11-03' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 6.2:
UAPI Changes:
Cross-subsystem Changes:
- dma-buf: locking improvements
- firmware: New API in the RaspberryPi firmware driver used by vc4
Core Changes:
- client: Null pointer dereference fix in drm_client_buffer_delete()
- mm/buddy: Add back random seed log
- ttm: Convert ttm_resource to use size_t for its size, fix for an
undefined behaviour
Driver Changes:
- bridge:
- adv7511: use dev_err_probe
- it6505: Fix return value check of pm_runtime_get_sync
- panel:
- sitronix: Fixes and clean-ups
- lcdif: Increase DMA burst size
- rockchip: runtime_pm improvements
- vc4: Fix for a regression preventing the use of 4k @ 60Hz, and
further HDMI rate constraints check.
- vmwgfx: Cursor improvements
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20221103083437.ksrh3hcdvxaof62l@houat
Commit ae71ab585c ("drm/vc4: hdmi: Enforce the minimum rate at
runtime_resume") reintroduced the call to clk_set_min_rate in an attempt
to fix the boot without a monitor connected on the RaspberryPi3.
However, that introduced a regression breaking the display output
entirely (black screen but no vblank timeout) on the Pi4.
This is due to the fact that we now have in a typical modeset at boot,
in vc4_hdmi_encoder_pre_crtc_configure(), we have a first call to
clk_set_min_rate() asking for the minimum rate of the HSM clock for our
given resolution, and then a call to pm_runtime_resume_and_get(). We
will thus execute vc4_hdmi_runtime_resume() which, since the commit
mentioned above, will call clk_set_min_rate() a second time with the
absolute minimum rate we want to enforce on the HSM clock.
We're thus effectively erasing the minimum mandated by the mode we're
trying to set. The fact that only the Pi4 is affected is due to the fact
that it uses a different clock driver that tries to minimize the HSM
clock at all time. It will thus lower the HSM clock rate to 120MHz on
the second clk_set_min_rate() call.
The Pi3 doesn't use the same driver and will not change the frequency on
the second clk_set_min_rate() call since it's still within the new
boundaries and it doesn't have the code to minimize the clock rate as
needed. So even though the boundaries are still off, the clock rate is
still the right one for our given mode, so everything works.
There is a lot of moving parts, so I couldn't find any obvious
solution:
- Reverting the original is not an option, as that would break the Pi3
again.
- We can't move the clk_set_min_rate() call in _pre_crtc_configure()
since because, on the Pi3, the HSM clock has the CLK_SET_RATE_GATE
flag which prevents the clock rate from being changed after it's
been enabled. Our calls to clk_set_min_rate() can change it, so they
need to be done before clk_prepare_enable().
- We can't remove the call to clk_prepare_enable() from the
runtime_resume hook to put it into _pre_crtc_configure() either,
since we need that clock to be enabled to access the registers, and
we can't count on the fact that the display will be active in all
situations (doing any CEC operation, or listing the modes while
inactive are valid for example()).
- We can't drop the call to clk_set_min_rate() in
_pre_crtc_configure() since we would need to still enforce the
minimum rate for a given resolution, and runtime_resume doesn't have
access to the current mode, if there's any.
- We can't copy the TMDS character rate into vc4_hdmi and reuse it
since, because it's part of the KMS atomic state, it needs to be
protected by a mutex. Unfortunately, some functions (CEC operations,
mostly) can be reentrant (through the CEC framework) and still need
a pm_runtime_get.
However, we can work around this issue by leveraging the fact that the
clk_set_min_rate() calls set boundaries for its given struct clk, and
that each different clk_get() call will return a different instance of
struct clk. The clock framework will then aggregate the boundaries for
each struct clk instances linked to a given clock, plus its hardware
boundaries, and will use that.
We can thus get an extra HSM clock user for runtime_pm use only, and use
our different clock instances depending on the context: runtime_pm will
use its own to set the absolute minimum clock setup so that we never
lock the CPU waiting for a register access, and the modeset part will
set its requirement for the current resolution. And we let the CCF do
the coordination.
It's not an ideal solution, but it's fairly unintrusive and doesn't
really change any part of the logic so it looks like a rather safe fix.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2136234
Fixes: ae71ab585c ("drm/vc4: hdmi: Enforce the minimum rate at runtime_resume")
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Link: https://lore.kernel.org/r/20221021131339.2203291-1-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
A comment introduced by commit 6bed2ea3cb ("drm/vc4: hdmi: Reset link
on hotplug") mentions a drm_atomic_helper_connector_hdmi_reset_link()
function that was part of the earlier versions but got moved internally
and is now named vc4_hdmi_reset_link(). Let's fix the function name.
Fixes: 6bed2ea3cb ("drm/vc4: hdmi: Reset link on hotplug")
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://lore.kernel.org/r/20221024093634.118190-2-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
We access some fields protected by our internal mutex in
vc4_hdmi_reset_link() (saved_adjusted_mode, output_bpc, output_format)
and are calling functions that need to have that lock taken
(vc4_hdmi_supports_scrambling()).
However, the current code doesn't lock that mutex. Let's make sure it
does.
Fixes: 6bed2ea3cb ("drm/vc4: hdmi: Reset link on hotplug")
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://lore.kernel.org/r/20221024093634.118190-1-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
At least the 4096x2160@60Hz mode requires some overclocking that isn't
available by default, even if hdmi_enable_4kp60 is enabled.
Let's add some logic to detect whether we can satisfy the core clock
requirements for that mode, and prevent it from being used otherwise.
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220815-rpi-fix-4k-60-v5-6-fe9e7ac8b111@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
In order to support higher HDMI frequencies, users have to set the
hdmi_enable_4kp60 parameter in their config.txt file.
This will have the side-effect of raising the maximum of the core clock,
tied to the HVS, and managed by the HVS driver.
However, we are querying this in the HDMI driver by poking into the HVS
structure to get our struct clk handle.
Let's make this part of the HVS bind implementation to have all the core
clock related setup in the same place.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220815-rpi-fix-4k-60-v5-5-fe9e7ac8b111@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
In order to support higher HDMI frequencies, users have to set the
hdmi_enable_4kp60 parameter in their config.txt file.
We were detecting this so far by calling clk_round_rate() on the core
clock with the frequency we're supposed to run at when one of those
modes is enabled. Whether or not the parameter was enabled could then be
inferred by the returned rate since the maximum clock rate reported by
the firmware was one of the side effect of setting that parameter.
However, the recent clock rework we did changed what clk_round_rate()
was returning to always return the minimum allowed, and thus this test
wasn't reliable anymore.
Let's use the new clk_get_max_rate() function to reliably determine the
maximum rate allowed on that clock and fix the 4k@60Hz output.
Fixes: e9d6cea2af ("clk: bcm: rpi: Run some clocks at the minimum rate allowed")
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220815-rpi-fix-4k-60-v5-4-fe9e7ac8b111@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
UAPI Changes:
- Documentation for page-flip flags
Cross-subsystem Changes:
- dma-buf: Add unlocked variant of vmapping and attachment-mapping
functions
Core Changes:
- atomic-helpers: CRTC primary plane test fixes
- connector: TV API consistency improvements, cmdline parsing
improvements
- crtc-helpers: Introduce drm_crtc_helper_atomic_check() helper
- edid: Fixes for HFVSDB parsing,
- fourcc: Addition of the Vivante tiled modifier
- makefile: Sort and reorganize the objects files
- mode_config: Remove fb_base from drm_mode_config_funcs
- sched: Add a module parameter to change the scheduling policy,
refcounting fix for fences
- tests: Sort the Kunit tests in the Makefile, improvements to the
DP-MST tests
- ttm: Remove unnecessary drm_mm_clean() call
Driver Changes:
- New driver: ofdrm
- Move all drivers to a common dma-buf locking convention
- bridge:
- adv7533: Remove dynamic lane switching
- it6505: Runtime PM support
- ps8640: Handle AUX defer messages
- tc358775: Drop soft-reset over I2C
- ast: Atomic Gamma LUT Support, Convert to SHMEM, various
improvements
- lcdif: Support for YUV planes
- mgag200: Fix PLL Setup on some revisions
- udl: Modesetting improvements, hot-unplug support
- vc4: Fix support for PAL-M
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCY1D3fQAKCRDj7w1vZxhR
xZZgAPoCSfyU3+M3ALT0vQ/OpktE5tuwUBMac2Lxkqgx4dnQ0gEAnYeez0Dedod8
HNdgBH7FTklYa/zT8n17SwHUOzJJ5gc=
=YvuW
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2022-10-20' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 6.2:
UAPI Changes:
- Documentation for page-flip flags
Cross-subsystem Changes:
- dma-buf: Add unlocked variant of vmapping and attachment-mapping
functions
Core Changes:
- atomic-helpers: CRTC primary plane test fixes
- connector: TV API consistency improvements, cmdline parsing
improvements
- crtc-helpers: Introduce drm_crtc_helper_atomic_check() helper
- edid: Fixes for HFVSDB parsing,
- fourcc: Addition of the Vivante tiled modifier
- makefile: Sort and reorganize the objects files
- mode_config: Remove fb_base from drm_mode_config_funcs
- sched: Add a module parameter to change the scheduling policy,
refcounting fix for fences
- tests: Sort the Kunit tests in the Makefile, improvements to the
DP-MST tests
- ttm: Remove unnecessary drm_mm_clean() call
Driver Changes:
- New driver: ofdrm
- Move all drivers to a common dma-buf locking convention
- bridge:
- adv7533: Remove dynamic lane switching
- it6505: Runtime PM support
- ps8640: Handle AUX defer messages
- tc358775: Drop soft-reset over I2C
- ast: Atomic Gamma LUT Support, Convert to SHMEM, various
improvements
- lcdif: Support for YUV planes
- mgag200: Fix PLL Setup on some revisions
- udl: Modesetting improvements, hot-unplug support
- vc4: Fix support for PAL-M
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20221020072405.g3o4hxuk75gmeumw@houat
This is a revert of commit fd5894fa24 ("drm/vc4: hdmi: Remove clock
rate initialization"), with the code slightly moved around.
It turns out that we can't downright remove that code from the driver,
since the Pi0-3 and Pi4 are in different cases, and it only works for
the Pi4.
Indeed, the commit mentioned above was relying on the RaspberryPi
firmware clocks driver to initialize the rate if it wasn't done by the
firmware. However, the Pi0-3 are using the clk-bcm2835 clock driver that
wasn't doing this initialization. We therefore end up with the clock not
being assigned a rate, and the CPU stalling when trying to access a
register.
We can't move that initialization in the clk-bcm2835 driver, since the
HSM clock we depend on is actually part of the HDMI power domain, so any
rate setup is only valid when the power domain is enabled. Thus, we
reinstated the minimum rate setup at runtime_suspend, which should
address both issues.
Link: https://lore.kernel.org/dri-devel/20220922145448.w3xfywkn5ecak2et@pengutronix.de/
Fixes: fd5894fa24 ("drm/vc4: hdmi: Remove clock rate initialization")
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220929-rpi-pi3-unplugged-fixes-v1-1-cd22e962296c@cerno.tech
We currently have two sets of TV properties.
The first one is there to deal with analog TV properties, creating
properties such as the TV mode, subconnectors, saturation, hue and so on.
It's created by calling the drm_mode_create_tv_properties() function.
The second one is there to deal with properties that might be useful on a
TV, creating the overscan margins for example. It's created by calling the
drm_mode_create_tv_margin_properties().
However, we also have a drm_atomic_helper_connector_tv_reset() function
that will reset the TV margin properties to their default values, and thus
is supposed to be called for the latter set. This creates an ambiguity due
to the inconsistent naming.
We can thus rename the drm_atomic_helper_connector_tv_reset() function to
drm_atomic_helper_connector_tv_margins_reset() to remove that ambiguity
and hopefully make it more obvious.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Link: https://lore.kernel.org/r/20220728-rpi-analog-tv-properties-v4-4-60d38873f782@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
During a hotplug cycle (such as a TV going out of suspend, or when the
cable is disconnected and reconnected), the expectation is that the same
state used before the disconnection is reused until the next commit.
However, the HDMI scrambling requires that some flags are set in the
monitor, and those flags are very likely to be reset when the cable has
been disconnected. This will thus result in a blank display, even if the
display pipeline configuration hasn't been modified or is in the exact
same state.
The solution we've had so far is to enable the scrambling-related bits
again on reconnection, but the HDMI 2.0 specification (Section 6.1.3.1 -
Scrambling Control) requires that the scrambling enable bit is set
before sending any scrambled video signal. Using that solution thus
breaks that expectation.
The solution used by i915 is to do a full modeset on the connector so
that we disable the video signal, enable the scrambling bit, and enable
the video signal again.
As such, we took that code and plugged it into vc4. It probably could
have been turned into an helper, but it proved to be difficult for
several reasons:
* i915 has fairly different structures than simpler KMS drivers such
as vc4, so doing some code that works with both proved to be
difficult;
* Other simpler drivers could reuse some of it (tegra, dw-hdmi), but
it would still require to move some parameters currently stored in
private structure that are needed to compute whether the scrambling
is needed or not, and then inform the driver that it needs to be
enabled. Some of those parameters are already in core structures
(drm_display_mode, drm_display_info, bpc), but the output format
isnt't. Adding it is fairly challenging since unlike the TMDS char
rate or mode, there's no consensus on what format to pick in
drivers, so it's not possible to write some generic code that can
depend on it.
For these reasons, we chose to duplicate the code for now, until someone
else really needs it as well, in which case we will be able to convert
it into a generic helper.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220829134731.213478-8-maxime@cerno.tech
We'll need it earlier in the driver, so let's move it next to the other
scrambling-related helpers.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220829134731.213478-7-maxime@cerno.tech
We'll need the locking context in future patch, so let's convert .detect
to .detect_ctx.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220829134731.213478-6-maxime@cerno.tech
Our detect callback has a bunch of operations to perform depending on
the current and last status of the connector, such a setting the CEC
physical address or enabling the scrambling again.
This is currently dealt with a bunch of if / else statetements that make
it fairly difficult to read and extend.
Let's move all that logic to a function of its own.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220829134731.213478-5-maxime@cerno.tech
We recently introduced a new mutex to protect concurrent execution of
ALSA and KMS hooks, and the concurrent access to some of vc4_hdmi
fields.
However, using it in the detect hook was creating a reentrency issue
with CEC code. Indeed, calling cec_s_phys_addr_from_edid from detect
might call the CEC adap_enable hook with the lock held, eventually
resulting in a deadlock.
Since we didn't really need to protect anything at the moment in the CEC
code, the decision was made to ignore the mutex in those CEC hooks,
working around the issue.
However, we can have the same thing happening if we end up triggering a
mode set from the detect callback, for example using
drm_atomic_helper_connector_hdmi_reset_link().
Since we don't really need to protect anything in detect either, let's
just drop the lock in detect, and add it again in CEC.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220829134731.213478-4-maxime@cerno.tech
Even though vc4_hdmi_supports_scrambling takes a mode as an argument, it
never uses it. Let's remove it.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220829134731.213478-3-maxime@cerno.tech
We don't modify the drm_display_mode pointer we have in the driver in
most places, so let's make them const.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220829134731.213478-2-maxime@cerno.tech
drm-misc-next for v6.1-rc1:
[airlied - fix sun4i_tv build]
UAPI Changes:
- Hide unregistered connectors from GETCONNECTOR ioctl.
- drm/virtio no longer advertises LINEAR modifier, as it doesn't work.
-
Cross-subsystem Changes:
- Fix GPF in udmabuf failure path.
Core Changes:
- Rework TTM placement to use intersect/compatible functions.
- Drop legacy DP-MST support.
- More DP-MST related fixes, and move all state into atomic.
- Make DRM_MIPI_DBI select DRM_KMS_HELPER.
- Add audio_infoframe packing for DP.
- Add logging when some atomic check functions fail.
- Assorted documentation updates and fixes.
Driver Changes:
- Assorted cleanups and fixes in msm, lcdif, nouveau, virtio,
panel/ilitek, bridge/icn6211, tve200, gma500, bridge/*, panfrost, via,
bochs, qxl, sun4i.
- Add add AUO B133UAN02.1, IVO M133NW4J-R3, Innolux N120ACA-EA1 eDP panels.
- Improve DP-MST modeset state handling in amdgpu, nouveau, i915.
- Drop DP-MST from radeon driver, it was broken and only user of legacy
DP-MST.
- Handle unplugging better in vc4.
- Simplify drm cmdparser tests.
- Add DP support to ti-sn65dsi86.
- Add MT8195 DP support to mediatek.
- Support RGB565, XRGB64, and ARGB64 formats in vkms.
- Convert sun4i tv support to atomic.
- Refactor vc4/vec TV Modesetting, and fix timings.
- Use atomic helpers instead of simple display helpers in ssd130x.
Maintainer changes:
- Add Douglas Anderson as reviewer for panel-edp.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/a489485b-3ebc-c734-0f80-aed963d89efe@linux.intel.com
UAPI Changes:
Cross-subsystem Changes:
- DMA-buf: documentation updates.
- Assorted small fixes to vga16fb
- Fix fbdev drivers to use the aperture helpers.
- Make removal of conflicting drivers work correctly without fbdev enabled.
Core Changes:
- bridge, scheduler, dp-mst: Assorted small fixes.
- Add more format helpers to fourcc, and use it to replace the cpp usage.
- Add DRM_FORMAT_Cxx, DRM_FORMAT_Rxx (single channel), and DRM_FORMAT_Dxx
("darkness", inverted single channel)
- Add packed AYUV8888 and XYUV8888 formats.
- Assorted documentation updates.
- Rename ttm_bo_init to ttm_bo_init_validate.
- Allow TTM bo's to exist without backing store.
- Convert drm selftests to kunit.
- Add managed init functions for (panel) bridge, crtc, encoder and connector.
- Fix endianness handling in various format conversion helpers.
- Make tests pass on big-endian platforms, and add test for rgb888 -> rgb565
- Move DRM_PLANE_HELPER_NO_SCALING to atomic helpers and rename, so
drm_plane_helper is no longer needed in most drivers.
- Use idr_init_base instead of idr_init.
- Rename FB and GEM CMA helpers to DMA helpers.
- Rework XRGB8888 related conversion helpers, and add drm_fb_blit() that
takes a iosys_map. Make drm_fb_memcpy take an iosys_map too.
- Move edid luminance calculation to core, and use it in i915.
Driver Changes:
- bridge/{adv7511,ti-sn65dsi86,parade-ps8640}, panel/{simple,nt35510,tc358767},
nouveau, sun4i, mipi-dsi, mgag200, bochs, arm, komeda, vmwgfx, pl111:
Assorted small fixes and doc updates.
- vc4: Rework hdmi power up, and depend on PM.
- panel/simple: Add Samsung LTL101AL01.
- ingenic: Add JZ4760(B) support, avoid a modeset when sharpness property
is unchanged, and use the new PM ops.
- Revert some amdgpu commits that cause garbaged graphics when starting
X, and reapply them with the real problem fixed.
- Completely rework vc4 init to use managed helpers.
- Rename via_drv to via_dri1, and move all stuff there only used by the
dri1 implementation in preperation for atomic modeset.
- Use regmap bulk write in ssd130x.
- Power sequence and clock updates to it6505.
- Split panel-sitrox-st7701 init sequence and rework mode programming code.
- virtio: Improve error and edge conditions handling, and convert to use managed
helpers.
- Add Samsung LTL101AL01, B120XAN01.0, R140NWF5 RH, DMT028VGHMCMI-1A T, panels.
- Add generic fbdev support to komeda.
- Split mgag200 modeset handling to make it more model-specific.
- Convert simpledrm to use atomic helpers.
- Improve udl suspend/disconnect handling.
-----BEGIN PGP SIGNATURE-----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=kU/l
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2022-08-20-1' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v6.1:
UAPI Changes:
Cross-subsystem Changes:
- DMA-buf: documentation updates.
- Assorted small fixes to vga16fb
- Fix fbdev drivers to use the aperture helpers.
- Make removal of conflicting drivers work correctly without fbdev enabled.
Core Changes:
- bridge, scheduler, dp-mst: Assorted small fixes.
- Add more format helpers to fourcc, and use it to replace the cpp usage.
- Add DRM_FORMAT_Cxx, DRM_FORMAT_Rxx (single channel), and DRM_FORMAT_Dxx
("darkness", inverted single channel)
- Add packed AYUV8888 and XYUV8888 formats.
- Assorted documentation updates.
- Rename ttm_bo_init to ttm_bo_init_validate.
- Allow TTM bo's to exist without backing store.
- Convert drm selftests to kunit.
- Add managed init functions for (panel) bridge, crtc, encoder and connector.
- Fix endianness handling in various format conversion helpers.
- Make tests pass on big-endian platforms, and add test for rgb888 -> rgb565
- Move DRM_PLANE_HELPER_NO_SCALING to atomic helpers and rename, so
drm_plane_helper is no longer needed in most drivers.
- Use idr_init_base instead of idr_init.
- Rename FB and GEM CMA helpers to DMA helpers.
- Rework XRGB8888 related conversion helpers, and add drm_fb_blit() that
takes a iosys_map. Make drm_fb_memcpy take an iosys_map too.
- Move edid luminance calculation to core, and use it in i915.
Driver Changes:
- bridge/{adv7511,ti-sn65dsi86,parade-ps8640}, panel/{simple,nt35510,tc358767},
nouveau, sun4i, mipi-dsi, mgag200, bochs, arm, komeda, vmwgfx, pl111:
Assorted small fixes and doc updates.
- vc4: Rework hdmi power up, and depend on PM.
- panel/simple: Add Samsung LTL101AL01.
- ingenic: Add JZ4760(B) support, avoid a modeset when sharpness property
is unchanged, and use the new PM ops.
- Revert some amdgpu commits that cause garbaged graphics when starting
X, and reapply them with the real problem fixed.
- Completely rework vc4 init to use managed helpers.
- Rename via_drv to via_dri1, and move all stuff there only used by the
dri1 implementation in preperation for atomic modeset.
- Use regmap bulk write in ssd130x.
- Power sequence and clock updates to it6505.
- Split panel-sitrox-st7701 init sequence and rework mode programming code.
- virtio: Improve error and edge conditions handling, and convert to use managed
helpers.
- Add Samsung LTL101AL01, B120XAN01.0, R140NWF5 RH, DMT028VGHMCMI-1A T, panels.
- Add generic fbdev support to komeda.
- Split mgag200 modeset handling to make it more model-specific.
- Convert simpledrm to use atomic helpers.
- Improve udl suspend/disconnect handling.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/f0c71766-61e8-19b7-763a-5fbcdefc633d@linux.intel.com
In vc4_hdmi_encoder_{pre,post}_crtc_enable() commit cd00ed5187
("drm/vc4: hdmi: Protect device resources after removal") missed to
unlock the mutex before returning due to drm_dev_enter() indicating the
device being unplugged.
Fixes: cd00ed5187 ("drm/vc4: hdmi: Protect device resources after removal")
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220824161327.330627-2-dakr@redhat.com
The current code tries to handle the case where CONFIG_PM isn't selected
by first calling our runtime_resume implementation and then properly
report the power state to the runtime_pm core.
This allows to have a functionning device even if pm_runtime_get_*
functions are nops.
However, the device power state if CONFIG_PM is enabled is
RPM_SUSPENDED, and thus our vc4_hdmi_write() and vc4_hdmi_read() calls
in the runtime_pm hooks will now report a warning since the device might
not be properly powered.
Even more so, we need CONFIG_PM enabled since the previous RaspberryPi
have a power domain that needs to be powered up for the HDMI controller
to be usable.
The previous patch has created a dependency on CONFIG_PM, now we can
just assume it's there and only call pm_runtime_resume_and_get() to make
sure our device is powered in bind.
Link: https://lore.kernel.org/r/20220629123510.1915022-39-maxime@cerno.tech
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
(cherry picked from commit 53565c28e6)
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
We already depend on runtime PM to get the power domains and clocks for
most of the devices supported by the vc4 driver, so let's just select it
to make sure it's there.
Link: https://lore.kernel.org/r/20220629123510.1915022-38-maxime@cerno.tech
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
(cherry picked from commit f1bc386b31)
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
This driver includes the deprecated OF GPIO header <linux/of_gpio.h>
yet fail to use symbols from it, so drop the include.
Cc: Emma Anholt <emma@anholt.net>
Cc: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Maíra Canal <mairacanal@riseup.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220812205746.609107-6-mairacanal@riseup.net
As diffstat shows, we've had lots of developments in a wide range
at this time; the majority of changes are about ASoC, including
subsystem-wide cleanups, continued SOF / Intel updates and a
bunch of new drivers (as usual), while there have been some
significant (but almost invisible) improvements in ALSA core
side, too. Below are some highlights:
Core:
- Faster lookups of control elements with Xarray; normal user
won't notice, but on the devices with tons of control elements,
it can be visibly faster
- Support for input validation for controls; this will harden
for badly written drivers in general with a slight overhead
- Deferred async signal handling for working around the potential
deadlocks
- Cleanup / refactoring raw MIDI locking code
ASoC:
- Restructing of the set_fmt() callbacks for making things clearer
in situations like CODEC to CODEC links
- Clean up and modernizing the DAI naming scheme setups
- Merge of more of the Intel AVS driver stack, including some
board integrations
- New version 4 mechanism for communication with SOF DSPs
- Suppoort for dynamically selecting the PLL to use at runtime on
i.MX platforms
- Improvements for CODEC to CODEC support in the generic cards
- Support for AMD Jadeite and various machines, AMD RPL, Intel
MetorLake DSPs, Mediatek MT8186 DSPs and MT6366, nVidia Tegra
MDDRC, OPE and PEQ, NXP TFA9890, Qualcomm SDM845, WCD9335 and
WAS883x, and Texas Instruments TAS2780
HD- and USB-audio:
- Continued improvement for CS35L41 (sub)codec support
- More quirks for various devices (HP, Lenovo, Dell, Clevo)
-----BEGIN PGP SIGNATURE-----
iQJCBAABCAAsFiEEIXTw5fNLNI7mMiVaLtJE4w1nLE8FAmLr5bcOHHRpd2FpQHN1
c2UuZGUACgkQLtJE4w1nLE93IQ/+OleeiGv7C487QN5MrBCkdFnSAiXsXDArcMgo
Gt6XLubH54et1tqi2ms4gRQOqr4HiBelERuqmaCLMZfEgVDc0VhJnf2jjhluYq9+
o9+kcYKul6qTZeNZLPjEX8pBvDe7HzOl7yep++ZnKeH6DAKNQQLDjVuOcQU/BXdY
kL8vYrLI3zfqj/pCePb5xpkBx4XdCrE3TfiCr3tAHVg9MyvSGOJyWs02mEBqQRnc
rlLmkjQVQyln/AGK4RAPMmrrFytktAvBjmIDyFL7kAzhdxe0ouNzTvdxESeojNJv
CVo/p3hl/+0LYjpD2x9v2pQuifOfpjwSCy6f8jsaF366sMwR1D45h051prILsxAF
05D5AOwMCnnJdFQFxw3mIkoDva3/PRX8GFfHsXoz+efc5Ibp8ksNYVgAJ3D2TTtt
7nAYMn0dimVDtw2LHiKantgWAs/rOqD3hDzGxFj2sR662ahsHr8pT8csnJAGoBvW
7kgx7ZzFo/wSyZJqVqV7p4g6J79ScehRwhqoiwZau9Eo+PhuxZUKvm4RwGFh0Vvg
GbiVRPfLV4xQd/pDin6qRX1M7cgPc62qGLkhQHAzrX6H5ipwIbQrpyDGLjwdSEp8
XcQmzCG1zGOvb9A8BY1VBOQXxZRTqN58XujbZ6hsms7Uw8sqagxpYLA/e1bvt1E1
RQoHQRw=
=1n0/
-----END PGP SIGNATURE-----
Merge tag 'sound-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"As the diffstat shows, we've had lots of developments in a wide range
at this time; the majority of changes are about ASoC, including
subsystem-wide cleanups, continued SOF / Intel updates and a bunch of
new drivers (as usual), while there have been some significant (but
almost invisible) improvements in ALSA core side, too.
Below are some highlights:
Core:
- Faster lookups of control elements with Xarray; normal user won't
notice, but on the devices with tons of control elements, it can be
visibly faster
- Support for input validation for controls; this will harden for
badly written drivers in general with a slight overhead
- Deferred async signal handling for working around the potential
deadlocks
- Cleanup / refactoring raw MIDI locking code
ASoC:
- Restructing of the set_fmt() callbacks for making things clearer in
situations like CODEC to CODEC links
- Clean up and modernizing the DAI naming scheme setups
- Merge of more of the Intel AVS driver stack, including some board
integrations
- New version 4 mechanism for communication with SOF DSPs
- Suppoort for dynamically selecting the PLL to use at runtime on
i.MX platforms
- Improvements for CODEC to CODEC support in the generic cards
- Support for AMD Jadeite and various machines, AMD RPL, Intel
MetorLake DSPs, Mediatek MT8186 DSPs and MT6366, nVidia Tegra
MDDRC, OPE and PEQ, NXP TFA9890, Qualcomm SDM845, WCD9335 and
WAS883x, and Texas Instruments TAS2780
HD- and USB-audio:
- Continued improvement for CS35L41 (sub)codec support
- More quirks for various devices (HP, Lenovo, Dell, Clevo)"
* tag 'sound-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (778 commits)
ALSA: hda/realtek: Add quirk for HP Spectre x360 15-eb0xxx
ALSA: line6: Replace sprintf() with sysfs_emit()
ALSA: hda: Replace sprintf() with sysfs_emit()
ALSA: pcm: Replace sprintf() with sysfs_emit()
ALSA: core: Replace scnprintf() with sysfs_emit()
ALSA: control-led: Replace sprintf() with sysfs_emit()
ALSA: aoa: Replace sprintf() with sysfs_emit()
ALSA: ac97: Replace sprintf() with sysfs_emit()
ALSA: hda/realtek: Add quirk for Clevo NV45PZ
ALSA: hda/realtek: Add quirk for Lenovo Yoga9 14IAP7
ALSA: control: Use deferred fasync helper
ALSA: pcm: Use deferred fasync helper
ALSA: timer: Use deferred fasync helper
ALSA: core: Add async signal helpers
ASoC: q6asm: use kcalloc() instead of kzalloc()
ACPI: scan: Add CLSA0101 Laptop Support
ALSA: hda: cs35l41: Support CLSA0101
ALSA: hda: cs35l41: Use the CS35L41 HDA internal define
ASoC: dt-bindings: use spi-peripheral-props.yaml
ASoC: codecs: va-macro: use fsgen as clock
...
mutex_init is supposed to be balanced by a call to mutex_destroy that we
were never doing in the vc4 driver.
Since a DRM-managed mutex_init variant has been introduced, let's just
switch to it.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220711173939.1132294-66-maxime@cerno.tech
The vc4 has a custom API to allow components to register a debugfs file
before the DRM driver has been registered and the debugfs_init hook has
been called.
However, the .late_register hook allows to have the debugfs file creation
deferred after that time already.
Let's remove our custom code to only register later our debugfs entries as
part of either debugfs_init or after it.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220711173939.1132294-65-maxime@cerno.tech
devm_pm_runtime_enable() simplifies the driver a bit since it will call
pm_runtime_disable() automatically through a device-managed action.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220711173939.1132294-49-maxime@cerno.tech
Whenever the device and driver are unbound, the main device and all the
subdevices will be removed by calling their unbind() method.
However, the DRM device itself will only be freed when the last user will
have closed it.
It means that there is a time window where the device and its resources
aren't there anymore, but the userspace can still call into our driver.
Fortunately, the DRM framework provides the drm_dev_enter() and
drm_dev_exit() functions to make sure our underlying device is still there
for the section protected by those calls. Let's add them to the HDMI driver.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220711173939.1132294-48-maxime@cerno.tech
The HDMI driver unbind hook doesn't have any ALSA-related code anymore, so
let's move the ALSA sanity checks and comments we have to some other part
of the driver dedicated to ALSA.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220711173939.1132294-47-maxime@cerno.tech
Commit 776efe800f ("drm/vc4: hdmi: Drop devm interrupt handler for
hotplug interrupts") dropped the device-managed interrupt registration
because it was creating bugs and races whenever an interrupt was coming in
while the device was removed.
However, our latest patches to the HDMI controller driver fix this as well,
so we can use device-managed interrupt handlers again.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220711173939.1132294-46-maxime@cerno.tech
The current code to build the registers set later exposed in debugfs for
the HDMI controller relies on traditional allocations, that are later
free'd as part of the driver unbind hook.
Since krealloc doesn't have a DRM-managed equivalent, let's add an action
to free the buffer later on.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220711173939.1132294-45-maxime@cerno.tech
The reference to the DDC controller device needs to be put back when we're
done with it. Let's use a device-managed action to simplify the driver.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220711173939.1132294-44-maxime@cerno.tech
The current code to unregister our CEC device needs to be undone manually
when we remove the HDMI driver.
Since the CEC framework will allocate its main structure, and will defer
its deallocation to when the last user will have closed it, we don't really
need to take any particular measure to prevent any use-after-free and can
thus use any managed action.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220711173939.1132294-43-maxime@cerno.tech
The current code to unregister our ALSA device needs to be undone manually
when we remove the HDMI driver.
Since ALSA doesn't seem to support any mechanism to defer freeing something
until the last user of the ALSA device is gone, we can either use a
device-managed or a DRM-managed action.
The consistent way would be to use a DRM-managed one, just like pretty much
any framework-facing structure should be doing. However, ALSA does a lot of
allocation and registration using device-managed calls. Thus, if we're
going that way, by the time the DRM-managed action would run all of those
allocation would have been freed and we would end up with a use-after-free.
Thus, let's do a device-managed action. It's been tested with KASAN enabled
and doesn't seem to trigger any issue, so it's as good as anything.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220711173939.1132294-42-maxime@cerno.tech
The current code will call drm_connector_unregister() and
drm_connector_cleanup() when the device is unbound. However, by then, there
might still be some references held to that connector, including by the
userspace that might still have the DRM device open.
Let's switch to a DRM-managed initialization to clean up after ourselves
only once the DRM device has been last closed.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220711173939.1132294-41-maxime@cerno.tech
The current code will call drm_encoder_cleanup() when the device is
unbound. However, by then, there might still be some references held to
that encoder, including by the userspace that might still have the DRM
device open.
Let's switch to a DRM-managed initialization to clean up after ourselves
only once the DRM device has been last closed.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220711173939.1132294-40-maxime@cerno.tech
drm_connector_unregister() is only to be used for connectors that have been
registered through drm_connector_register() after drm_dev_register() has
been called. This is our case here so let's remove the call.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220711173939.1132294-39-maxime@cerno.tech
Our internal structure that stores the DRM entities structure is allocated
through a device-managed kzalloc.
This means that this will eventually be freed whenever the device is
removed. In our case, the most likely source of removal is that the main
device is going to be unbound, and component_unbind_all() is being run.
However, it occurs while the DRM device is still registered, which will
create dangling pointers, eventually resulting in use-after-free.
Switch to a DRM-managed allocation to keep our structure until the DRM
driver doesn't need it anymore.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220711173939.1132294-38-maxime@cerno.tech
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmLLR2MeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG+hMH/jKGMOAbicR/CRq8
WLKmpb1eTJP2dbeiEs5amBk9DZQhqjx6tIQRCpZoGxBL+XWq7DX2fRLkAT56yS5/
NwferpR6IR9GlhjbfczF0JuQkP6eRUXnLrIKS5MViLI5QrCI80kkj4/mdqUXSiBV
cMfXl5T1j+pb3zHUVXjnmvY+77q6rZTPoGxa/l8d6MaIhAg+jhu2E1HaSaSCX/YK
TViq7ciI9cXoFV9yqhLkkBdGjBV8VQsKmeWEcA738bdSy1WAJSV1SVTJqLFvwdPI
PM1asxkPoQ7jRrwsY4G8pZ3zPskJMS4Qwdn64HK+no2AKhJt2p6MePD1XblcrGHK
QNStMY0=
=LfuD
-----END PGP SIGNATURE-----
Backmerge tag 'v5.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux into drm-next
Backmerge in rc6 so I can merge msm next easier.
Linux 5.19-rc6
Signed-off-by: Dave Airlie <airlied@redhat.com>
The current code tries to handle the case where CONFIG_PM isn't selected
by first calling our runtime_resume implementation and then properly
report the power state to the runtime_pm core.
This allows to have a functionning device even if pm_runtime_get_*
functions are nops.
However, the device power state if CONFIG_PM is enabled is
RPM_SUSPENDED, and thus our vc4_hdmi_write() and vc4_hdmi_read() calls
in the runtime_pm hooks will now report a warning since the device might
not be properly powered.
Even more so, we need CONFIG_PM enabled since the previous RaspberryPi
have a power domain that needs to be powered up for the HDMI controller
to be usable.
The previous patch has created a dependency on CONFIG_PM, now we can
just assume it's there and only call pm_runtime_resume_and_get() to make
sure our device is powered in bind.
Link: https://lore.kernel.org/r/20220629123510.1915022-39-maxime@cerno.tech
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
We already depend on runtime PM to get the power domains and clocks for
most of the devices supported by the vc4 driver, so let's just select it
to make sure it's there.
Link: https://lore.kernel.org/r/20220629123510.1915022-38-maxime@cerno.tech
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
With the change to 2 pixels/clock, the pixel doubling in the PV
results in doubling each pair of pixels, ie ABABCDCD instead of
AABBCCDD.
Move the pixel doubling to the HDMI block, however this means
that DBLCLK modes now fall foul of requiring even values for
all the horizontal timing parameters.
As both 480i and 576i fail this, attempt to fix up DBLCLK modes
that have odd timings values.
Fixes: 8323989140 ("drm/vc4: hdmi: Support the BCM2711 HDMI controllers")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-34-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
For interlaced modes the timings were not being correctly
programmed into the HDMI block, so correct them.
Fixes: 8323989140 ("drm/vc4: hdmi: Support the BCM2711 HDMI controllers")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-33-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Whenever the maximum BPC is changed, vc4_hdmi_encoder_compute_config()
might pick up a different BPC or format depending on the display
capabilities.
That change will have a number of side effects, including the clock
rates and whether the scrambling is enabled.
However, only drm_crtc_state.connectors_changed will be set to true,
since that properly only affects the connector.
This means that while drm_atomic_crtc_needs_modeset() will return true,
and thus drm_atomic_helper_commit_modeset_enables() will call our
encoder atomic_enable() hook, mode_changed will be false.
So crtc_set_mode() will not call our encoder .atomic_mode_set() hook. We
use this hook in vc4 to set the vc4_hdmi_connector_state.output_bpc (and
output_format), and will then reuse the value in .atomic_enable() to select
whether or not scrambling should be enabled.
However, since our clock rate is pre-computed during .atomic_check(), we
end up with the clocks properly configured, but the scrambling disabled,
leading to a blank screen.
Let's set mode_changed to true in our HDMI driver to force the update of
output_bpc, and thus prevent the issue entirely.
Fixes: ba8c0faebb ("drm/vc4: hdmi: Enable 10/12 bpc output")
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Link: https://lore.kernel.org/r/20220613144800.326124-32-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Increase the number of post-sync blanking lines on odd fields instead of
decreasing it on even fields. This makes the total number of lines
properly match the modelines.
Additionally fix the value of PV_VCONTROL_ODD_DELAY, which did not take
pixels_per_clock into account, causing some displays to invert the
fields when driven by bcm2711.
Fixes: 682e62c454 ("drm/vc4: Fix support for interlaced modes on HDMI.")
Signed-off-by: Mateusz Kwiatkowski <kfyatek+publicgit@gmail.com>
Link: https://lore.kernel.org/r/20220613144800.326124-31-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
This bit ensures data island packets are never generated when disallowed
by HDCP. As no Pi boards support HDCP this is providing an unnecessary
restriction
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Link: https://lore.kernel.org/r/20220613144800.326124-27-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
This path actually occurs when audio is started during a hdmi mode set.
As the data will be written by vc4_hdmi_set_infoframes when packet RAM
is enabled again, don't treat as an error
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Link: https://lore.kernel.org/r/20220613144800.326124-26-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The current HDMI driver, in vc4_hdmi_audio_can_stream() checks whether
the display output is enabled.
This has been there in one form or the other since the introduction of
the audio support in the VC4 HDMI driver in commit bb7d785688
("drm/vc4: Add HDMI audio support"), but no justification for this check
is in the commit message, or in the discussions around the patches.
One can only assume this was done to prevent a user from playing audio
on the ALSA soundcard when the monitor doesn't support it.
However, this is causing some issues. Indeed, Kodi, for example, was
hitting some errors if it was streaming audio during a modeset. With the
theory above, it does make sense, but the display and audio threads are
typically completely different processes with no opportunity to
synchronise which makes it hard to workaround.
Removing that check also doesn't seem to cause any trouble, so let's
just remove it.
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Link: https://lore.kernel.org/r/20220613144800.326124-25-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The BCM2835-37 found in the RaspberryPi 0 to 3 have a power domain
attached to the HDMI block, handled in Linux through runtime_pm.
That power domain is shared with the VEC block, so even if we put our
runtime_pm reference in the HDMI driver it would keep being on. If the
VEC is disabled though, the power domain would be disabled and we would
lose any initialization done in our bind implementation.
That initialization involves calling the reset function and initializing
the CEC registers.
Let's move the initialization to our runtime_resume implementation so
that we initialize everything properly if we ever need to.
Fixes: c86b412143 ("drm/vc4: hdmi: Move the HSM clock enable to runtime_pm")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-24-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The HDMI block can repeat pixels for double clocked modes,
and the firmware is now configuring the block to do this as
the PV is doing it incorrectly when at 2pixels/clock.
If the kernel doesn't reset it then we end up with strange
modes.
Reset MISC_CONTROL.
Fixes: 8323989140 ("drm/vc4: hdmi: Support the BCM2711 HDMI controllers")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-22-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
We are getting occasional VC4_HD_MAI_CTL_ERRORF in
HDMI_MAI_CTL which seem to correspond with audio dropouts.
Reduce the threshold where we deassert DREQ to avoid the fifo
overfilling
Fixes: bb7d785688 ("drm/vc4: Add HDMI audio support")
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Link: https://lore.kernel.org/r/20220613144800.326124-21-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Using a hdmi analyser the bytes in packet ram
registers beyond the length were visible in the
infoframes and it flagged the checksum as invalid.
Zeroing unused words of packet RAM avoids this
Fixes: 21317b3fba ("drm/vc4: Set up the AVI and SPD infoframes.")
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Link: https://lore.kernel.org/r/20220613144800.326124-20-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The vc5 HDMI registers hadn't been added into the debugfs
register sets, therefore weren't dumped on request.
Add them in.
Fixes: 8323989140 ("drm/vc4: hdmi: Support the BCM2711 HDMI controllers")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-19-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The dmas property is used to hold the dmaengine channel used for audio
output.
Older device trees were missing that property, so if it's not there we
disable the audio output entirely.
However, some overlays have set an empty value to that property, mostly
to workaround the fact that overlays cannot remove a property. Let's add
a test for that case and if it's empty, let's disable it as well.
Cc: <stable@vger.kernel.org>
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Link: https://lore.kernel.org/r/20220613144800.326124-18-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Change the legacy DAI naming flag from opting in to the new scheme
(non_legacy_dai_naming), to opting out of it (legacy_dai_naming).
This driver appears to be on the CPU side of the DAI link and
currently uses the legacy naming, so add the new flag.
Acked-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220623125250.2355471-4-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
drivers/gpu/drm/vc4/vc4_hdmi.c: In function ‘vc4_hdmi_connector_detect’:
drivers/gpu/drm/vc4/vc4_hdmi.c:228:7: error: implicit declaration of function ‘gpiod_get_value_cansleep’; did you mean ‘gpio_get_value_cansleep’? [-Werror=implicit-function-declaration]
if (gpiod_get_value_cansleep(vc4_hdmi->hpd_gpio))
^~~~~~~~~~~~~~~~~~~~~~~~
gpio_get_value_cansleep
CC [M] drivers/gpu/drm/vc4/vc4_validate.o
CC [M] drivers/gpu/drm/vc4/vc4_v3d.o
CC [M] drivers/gpu/drm/vc4/vc4_validate_shaders.o
CC [M] drivers/gpu/drm/vc4/vc4_debugfs.o
drivers/gpu/drm/vc4/vc4_hdmi.c: In function ‘vc4_hdmi_bind’:
drivers/gpu/drm/vc4/vc4_hdmi.c:2883:23: error: implicit declaration of function ‘devm_gpiod_get_optional’; did you mean ‘devm_clk_get_optional’? [-Werror=implicit-function-declaration]
vc4_hdmi->hpd_gpio = devm_gpiod_get_optional(dev, "hpd", GPIOD_IN);
^~~~~~~~~~~~~~~~~~~~~~~
devm_clk_get_optional
drivers/gpu/drm/vc4/vc4_hdmi.c:2883:59: error: ‘GPIOD_IN’ undeclared (first use in this function); did you mean ‘GPIOF_IN’?
vc4_hdmi->hpd_gpio = devm_gpiod_get_optional(dev, "hpd", GPIOD_IN);
^~~~~~~~
GPIOF_IN
drivers/gpu/drm/vc4/vc4_hdmi.c:2883:59: note: each undeclared identifier is reported only once for each function it appears in
cc1: all warnings being treated as errors
Fixes: 6800234cee ("drm/vc4: hdmi: Convert to gpiod")
Signed-off-by: Hui Tang <tanghui20@huawei.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220510135148.247719-1-tanghui20@huawei.com
SCDC is the Status and Control Data Channel for HDMI. Move the SCDC
helpers into display/ and split the header into files for core and
helpers. Update all affected drivers. No functional changes.
To avoid the proliferation of Kconfig options, SCDC is part of DRM's
support for HDMI. If necessary, a new option could make SCDC an
independent feature.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421073108.19226-9-tzimmermann@suse.de
Move DRM's HMDI helpers into the display/ subdirectoy and add it
to DRM's display helpers. Update all affected drivers. No functional
changes.
The HDMI helpers were implemented in the EDID and connector code, but
are actually unrelated. With the move to the display-helper library, we
can remove the dependency on drm_edid.{c,h} in some driver's HDMI source
files.
Several of the HDMI helpers remain in EDID code because both share parts
of their implementation internally. With better refractoring of the EDID
code, those HDMI helpers could be moved into the display-helper library
as well.
v3:
* fix Kconfig dependencies (Javier)
v2:
* reduce HDMI helpers to avoid exporting functions (Jani)
* fix include statements (Jani, Javier)
* update Kconfig symbols
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421073108.19226-8-tzimmermann@suse.de
The vc4_hdmi_encoder struct was used exclusively to cache the value
returned by drm_detect_hdmi_monitor() in order to avoid calling it
multiple times.
Now that drm_detect_hdmi_monitor() has been replaced with
drm_display_info.is_hdmi, there is no need to have an extra struct.
Remove vc4_hdmi_encoder.
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220420114500.187664-3-jose.exposito89@gmail.com
Once EDID is parsed, the monitor HDMI support information is cached in
drm_display_info.is_hdmi by drm_parse_hdmi_vsdb_video().
This driver calls drm_detect_hdmi_monitor() to receive the same
information and stores its own cached value in
vc4_hdmi_encoder.hdmi_monitor, which is less efficient.
Avoid calling drm_detect_hdmi_monitor() and use drm_display_info.is_hdmi
instead. This also allows to remove vc4_hdmi_encoder.hdmi_monitor.
drm_detect_hdmi_monitor() is called in vc4_hdmi_connector_detect() and
vc4_hdmi_connector_get_modes(). In both cases it is safe to rely on
drm_display_info.is_hdmi as shown by ftrace:
$ sudo trace-cmd record -p function_graph -l "vc4_hdmi_*" -l "drm_*"
vc4_hdmi_connector_detect:
vc4_hdmi_connector_detect() {
drm_get_edid() {
drm_connector_update_edid_property() {
drm_add_display_info() {
drm_reset_display_info();
drm_for_each_detailed_block.part.0();
drm_parse_cea_ext() {
drm_find_cea_extension();
drm_parse_hdmi_vsdb_video();
/* drm_display_info.is_hdmi is cached here */
}
}
}
}
/* drm_display_info.is_hdmi is used here */
}
vc4_hdmi_connector_get_modes:
vc4_hdmi_connector_get_modes() {
drm_get_edid() {
drm_connector_update_edid_property() {
drm_add_display_info() {
drm_reset_display_info();
drm_for_each_detailed_block.part.0();
drm_parse_cea_ext() {
drm_find_cea_extension();
drm_parse_hdmi_vsdb_video();
/* drm_display_info.is_hdmi is cached here */
}
}
}
}
/* drm_display_info.is_hdmi is used here */
drm_connector_update_edid_property();
}
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220420114500.187664-2-jose.exposito89@gmail.com
Now that the clock driver makes sure we never end up with a rate of 0,
the HDMI driver doesn't need to care anymore.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://lore.kernel.org/r/20220225143534.405820-13-maxime@cerno.tech
In addition to the RGB444 output, the BCM2711 HDMI controller supports
the YUV444 and YUV422 output formats.
Let's add support for them in the driver, but still use RGB as the
preferred format.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220222164042.403112-8-maxime@cerno.tech
Currently we take the max_bpc property as the bpc value and do not try
anything else.
However, what the other drivers seem to be doing is that they would try
with the highest bpc allowed by the max_bpc property and the hardware
capabilities, test if it results in an acceptable configuration, and if
not decrease the bpc and try again.
Let's use the same logic.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220222164042.403112-7-maxime@cerno.tech
The current code only base its decision for whether the scrambler must be
enabled or not on the pixel clock of the mode, but doesn't take the bits
per color into account.
Let's leverage the new function to compute the clock rate in the
scrambler setup code.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220222164042.403112-6-maxime@cerno.tech
In the function that validates that the clock isn't too high, we've only
taken our controller limitations into account so far.
However, the sink can have a limit on the maximum TMDS clock it can deal
with too which is exposed through the EDID and the drm_display_info.
Make sure we check it.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220222164042.403112-5-maxime@cerno.tech
The code to compute our clock rate for a given setup will be called in
multiple places in the next patches, so let's create a separate function
for it.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220222164042.403112-4-maxime@cerno.tech
The pixel_rate field in the vc4_hdmi_connector_state struct actually
stores the TMDS character rate, let's rename it for consistency.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220222164042.403112-2-maxime@cerno.tech
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmIb/PEeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGugMH/R8icwG5gOjAuxBr
fuz9032ECVFS36Cy3ps9Eqgf5EdS4G6yz3joM4aNtp4B7e5FzI9lzBaHS8OAguNL
y7puFtBr9CywsnniJumZzciB9pEHmF/yyEKfMlRZA3JsRfLDacFstETp+duJnXoA
+s49IWsy1ot5zoherhDXcFLqDoFhLVU4hYwE1xpLpW/cllqmSnW8SDZMtWW1Ui/B
Of7zqINR4zBMmRjP4ymGq/ZrPWlFyWLdtOo0xxVoAQkeMgm33kfaaeGzfyK25FqR
JDGUZ7lkKvwz3PYh2hqJ7dc5K+vhJ18I+F1UmOiL6QAAUF/k8jq7i3Qaf6MKqh2Z
2v+A5k0=
=Hiar
-----END PGP SIGNATURE-----
Backmerge tag 'v5.17-rc6' into drm-next
This backmerges v5.17-rc6 so I can merge some amdgpu and some tegra changes on top.
Signed-off-by: Dave Airlie <airlied@redhat.com>
UAPI Changes:
Cross-subsystem Changes:
- Split out panel-lvds and lvds dt bindings .
- Put yes/no on/off disabled/enabled strings in linux/string_helpers.h
and use it in drivers and tomoyo.
- Clarify dma_fence_chain and dma_fence_array should never include eachother.
- Flatten chains in syncobj's.
- Don't double add in fbdev/defio when page is already enlisted.
- Don't sort deferred-I/O pages by default in fbdev.
Core Changes:
- Fix missing pm_runtime_put_sync in bridge.
- Set modifier support to only linear fb modifier if drivers don't
advertise support.
- As a result, we remove allow_fb_modifiers.
- Add missing clear for EDID Deep Color Modes in drm_reset_display_info.
- Assorted documentation updates.
- Warn once in drm_clflush if there is no arch support.
- Add missing select for dp helper in drm_panel_edp.
- Assorted small fixes.
- Improve fb-helper's clipping handling.
- Don't dump shmem mmaps in a core dump.
- Add accounting to ttm resource manager, and use it in amdgpu.
- Allow querying the detected eDP panel through debugfs.
- Add helpers for xrgb8888 to 8 and 1 bits gray.
- Improve drm's buddy allocator.
- Add selftests for the buddy allocator.
Driver Changes:
- Add support for nomodeset to a lot of drm drivers.
- Use drm_module_*_driver in a lot of drm drivers.
- Assorted small fixes to bridge/lt9611, v3d, vc4, vmwgfx, mxsfb, nouveau,
bridge/dw-hdmi, panfrost, lima, ingenic, sprd, bridge/anx7625, ti-sn65dsi86.
- Add bridge/it6505.
- Create DP and DVI-I connectors in ast.
- Assorted nouveau backlight fixes.
- Rework amdgpu reset handling.
- Add dt bindings for ingenic,jz4780-dw-hdmi.
- Support reading edid through aux channel in ingenic.
- Add a drm driver for Solomon SSD130x OLED displays.
- Add simple support for sharp LQ140M1JW46.
- Add more panels to nt35560.
-----BEGIN PGP SIGNATURE-----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=HuwD
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2022-02-23' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.18:
UAPI Changes:
Cross-subsystem Changes:
- Split out panel-lvds and lvds dt bindings .
- Put yes/no on/off disabled/enabled strings in linux/string_helpers.h
and use it in drivers and tomoyo.
- Clarify dma_fence_chain and dma_fence_array should never include eachother.
- Flatten chains in syncobj's.
- Don't double add in fbdev/defio when page is already enlisted.
- Don't sort deferred-I/O pages by default in fbdev.
Core Changes:
- Fix missing pm_runtime_put_sync in bridge.
- Set modifier support to only linear fb modifier if drivers don't
advertise support.
- As a result, we remove allow_fb_modifiers.
- Add missing clear for EDID Deep Color Modes in drm_reset_display_info.
- Assorted documentation updates.
- Warn once in drm_clflush if there is no arch support.
- Add missing select for dp helper in drm_panel_edp.
- Assorted small fixes.
- Improve fb-helper's clipping handling.
- Don't dump shmem mmaps in a core dump.
- Add accounting to ttm resource manager, and use it in amdgpu.
- Allow querying the detected eDP panel through debugfs.
- Add helpers for xrgb8888 to 8 and 1 bits gray.
- Improve drm's buddy allocator.
- Add selftests for the buddy allocator.
Driver Changes:
- Add support for nomodeset to a lot of drm drivers.
- Use drm_module_*_driver in a lot of drm drivers.
- Assorted small fixes to bridge/lt9611, v3d, vc4, vmwgfx, mxsfb, nouveau,
bridge/dw-hdmi, panfrost, lima, ingenic, sprd, bridge/anx7625, ti-sn65dsi86.
- Add bridge/it6505.
- Create DP and DVI-I connectors in ast.
- Assorted nouveau backlight fixes.
- Rework amdgpu reset handling.
- Add dt bindings for ingenic,jz4780-dw-hdmi.
- Support reading edid through aux channel in ingenic.
- Add a drm driver for Solomon SSD130x OLED displays.
- Add simple support for sharp LQ140M1JW46.
- Add more panels to nt35560.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/686ec871-e77f-c230-22e5-9e3bb80f064a@linux.intel.com
struct drm_display_mode embeds a list head, so overwriting
the full struct with another one will corrupt the list
(if the destination mode is on a list). Use drm_mode_copy()
instead which explicitly preserves the list head of
the destination mode.
Even if we know the destination mode is not on any list
using drm_mode_copy() seems decent as it sets a good
example. Bad examples of not using it might eventually
get copied into code where preserving the list head
actually matters.
Obviously one case not covered here is when the mode
itself is embedded in a larger structure and the whole
structure is copied. But if we are careful when copying
into modes embedded in structures I think we can be a
little more reassured that bogus list heads haven't been
propagated in.
@is_mode_copy@
@@
drm_mode_copy(...)
{
...
}
@depends on !is_mode_copy@
struct drm_display_mode *mode;
expression E, S;
@@
(
- *mode = E
+ drm_mode_copy(mode, &E)
|
- memcpy(mode, E, S)
+ drm_mode_copy(mode, E)
)
@depends on !is_mode_copy@
struct drm_display_mode mode;
expression E;
@@
(
- mode = E
+ drm_mode_copy(&mode, &E)
|
- memcpy(&mode, E, S)
+ drm_mode_copy(&mode, E)
)
@@
struct drm_display_mode *mode;
@@
- &*mode
+ mode
Cc: Emma Anholt <emma@anholt.net>
Cc: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220218100403.7028-18-ville.syrjala@linux.intel.com
On bind we will register the HDMI codec device but we don't unregister
it on unbind, leading to a device leakage. Unregister our device at
unbind.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220127111452.222002-1-maxime@cerno.tech
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmIJZmoeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGZdoH/04d8zUhM3Fd3ACB
V/ONtOXmkfP2mEJSjb7cXTN1EM2SlOBdSnSsEw09FtGhjHABjOnLho4J5ixk9TH8
zNMNI3EMksM2T9KadHwxv8Vvp1LTrWRzMbws8tOCPA0RkOpikJfClC8CzRAyidJ3
cAbbDH/Jl1GnVZ8bpKmv2auYt+kNVGb0cwJ2W8phCwwkL7sLky5tgYeaGiJEXbJf
Tfi/3qtFdmYjD8wtYnCfzjnB7suG5nF7rGEnxCIxNi+IA4DieUv2c1KchuoaBfT9
df364VjKaGT3j+GB07ksQ/8mkwWiRXsCzOXAyMZSZaWjdMD4aAhCTJak5j7/TvGC
wtgHPww=
=/CMW
-----END PGP SIGNATURE-----
Backmerge tag 'v5.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux into drm-next
Daniel asked for this for some intel deps, so let's do it now.
Signed-off-by: Dave Airlie <airlied@redhat.com>
The 2711 pixel valve can't produce odd horizontal timings, and
checks were added to vc4_hdmi_encoder_atomic_check and
vc4_hdmi_encoder_mode_valid to filter out/block selection of
such modes.
Modes with DRM_MODE_FLAG_DBLCLK double all the horizontal timing
values before programming them into the PV. The PV values,
therefore, can not be odd, and so the modes can be supported.
Amend the filtering appropriately.
Fixes: 57fb32e632 ("drm/vc4: hdmi: Block odd horizontal timings")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220127135116.298278-1-maxime@cerno.tech
The code that set the scdc_enabled flag to ensure it was
disabled at boot time also ran on Pi0-3 where there is no
SCDC support. This lead to a warning in vc4_hdmi_encoder_post_crtc_disable
due to vc4_hdmi_disable_scrambling being called and trying to
read (and write) register HDMI_SCRAMBLER_CTL which doesn't
exist on those platforms.
Only set the flag should the interface be configured to support
more than HDMI 1.4.
Fixes: 1998646129 ("drm/vc4: hdmi: Introduce a scdc_enabled flag")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220127134559.292778-1-maxime@cerno.tech
The existing logic was flawed in that it could try reading the
2711 specific registers for HPD on a CM1/3 where the HPD GPIO
hadn't been defined in DT.
Ensure we don't do the 2711 register read on invalid hardware,
and then
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220127131754.236074-1-maxime@cerno.tech
When we have the entire DRM state, retrieving the connector state only
requires the drm_connector pointer. Fortunately for us, we have
allocated it as a part of the vc4_hdmi structure, so we can retrieve get
a pointer by simply accessing our field in that structure.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220127111404.221882-1-maxime@cerno.tech
In order to support the YUV output, we'll need the atomic state to know
what is the state of the associated property in the CSC setup callback.
Let's change the prototype of that callback to allow us to access it.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220120151625.594595-11-maxime@cerno.tech
The current CSC setup code for the BCM2711 uses a sequence of register
writes to configure the CSC depending on whether we output using a full
or limited range.
However, with the upcoming introduction of the YUV output, we're going
to add new matrices to perform the conversions, so we should switch to
something a bit more flexible that takes the matrix as an argument and
programs the CSC accordingly.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220120151625.594595-10-maxime@cerno.tech
