This cleans up the mixer widget names. The AIF1 AD0 Mixer names were
previously wrong -- they do not control the digital side of the ADC. The
DAC mixer widgets were not wrong, but they were verbose and did not
match the naming scheme of the other widgets.
The mixer controls are not renamed because they are exposed to
userspace.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20201001021148.15852-5-samuel@sholland.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Sort the remaining pieces of the DAPM driver so that they are all in the
same order among controls/widgets/routes, and so they roughly match the
register word and bit order of the hardware. This nicely separates the
AIF-related widgets from the ADC/DAC widgets, which allows the AIF
widgets to stay in a logical order as more AIFs are added to the driver.
No widgets are renamed, to ease verification that this commit makes no
functional change.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20201001021148.15852-4-samuel@sholland.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This matches the module power-up/down sequence from the vendor's driver.
While updating these widgets/routes, reorder them to match the register
and bit layout of the hardware. This puts them in the same place in the
widget and route arrays (previously they were at opposite ends), and it
makes it easier to track which parts of which registers are implemented.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20201001021148.15852-3-samuel@sholland.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The sun8i codec is effectively an on-die variant of the X-Powers AC100
codec. The AC100 can derive its clocks from either of two I2S master
clocks or an internal PLL. For the on-die variant, Allwinner replaced
the codec's own PLL with a connection to SoC's existing PLL_AUDIO, and
they connected both I2S MCLK inputs to the same source -- which happens
to be an integer divider from the same PLL_AUDIO.
So there's actually no clocking flexibility. To run SYSCLK at the
required rate, it must be run straight from the PLL. The only choice is
whether it goes through AIF1CLK or AIF2CLK. Since both run at the same
rate, the only effect of that choice is which field in SYS_SR_CTRL
(AIF1_FS or AIF2_FS) controls the system sample rate.
Since AIFnCLK is required to bring up the corresponding DAI, and AIF1
(connected to the CPU) is used most often, let's use AIF1CLK as the
SYSCLK parent. That means we no longer need to set AIF2_FS.
Since this clock tree never changes, we can program it from the
component probe function, instead of using DAPM widgets. The DAPM
widgets unnecessarily change clock parents when the codec goes in/out
of idle and the supply widgets are powered up/down.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20201001021148.15852-2-samuel@sholland.org
Signed-off-by: Mark Brown <broonie@kernel.org>
By representing the module clock as a DAPM widget, we ensure that the
clock is only enabled when the module is actually in use, without
additional code in runtime PM hooks.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20200831034852.18841-10-samuel@sholland.org
Signed-off-by: Mark Brown <broonie@kernel.org>
When attached to the regmap, the bus clock is automatically enabled as
needed to access device registers. This avoids needing code to manage it
separately in the driver.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20200831034852.18841-9-samuel@sholland.org
Signed-off-by: Mark Brown <broonie@kernel.org>
All other definitions are sorted from largest to smallest bit number.
This makes the AIF1CLK_CTRL mask constants consistent with them.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20200831034852.18841-8-samuel@sholland.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Several fields have inconsistent indentation, presumably because the
patch "looked correct" due to the additional "+" character at the
beginning of the line.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20200831034852.18841-7-samuel@sholland.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Even though they are for the left channel mixer, they are documented as
"MXR_SRC". This matches the naming scheme used for the main DAC. The "R"
is part of the abbreviation for "mixer", not a reference to the channel.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20200831034852.18841-5-samuel@sholland.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver is for the digital part of the codec only. The analog part,
including the microphone inputs, is managed by a separate driver. These
widgets look like they were copied from sun4i-codec. Since they do not
perform any function in this driver, remove them.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20200831034852.18841-2-samuel@sholland.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Due to a mistake made while reordering patches, commit 90cac93297
("ASoC: sun8i-codec: Fix DAPM to match the hardware topology") added
the sun8i_codec_component_probe function without referencing it from
the component definition. Add the reference so the probe function gets
called as expected.
Fixes: 90cac93297 ("ASoC: sun8i-codec: Fix DAPM to match the hardware topology")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20200819034038.46418-1-samuel@sholland.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This series performs some minor cleanup on the driver for the analog
codec in the Allwinner A64, and hooks up the existing mute switches to
DAPM widgets, in order to provide improved power management.
Changes since v1:
- Collected Acked-by/Reviewed-by tags
- Used SOC_MIXER_NAMED_CTL_ARRAY to avoid naming a widget "Earpiece"
Samuel Holland (8):
ASoC: sun50i-codec-analog: Fix duplicate use of ADC enable bits
ASoC: sun50i-codec-analog: Gate the amplifier clock during suspend
ASoC: sun50i-codec-analog: Group and sort mixer routes
ASoC: sun50i-codec-analog: Make headphone routes stereo
ASoC: sun50i-codec-analog: Enable DAPM for headphone switch
ASoC: sun50i-codec-analog: Make line out routes stereo
ASoC: sun50i-codec-analog: Enable DAPM for line out switch
ASoC: sun50i-codec-analog: Enable DAPM for earpiece switch
sound/soc/sunxi/sun50i-codec-analog.c | 176 ++++++++++++++++----------
1 file changed, 111 insertions(+), 65 deletions(-)
--
2.26.2
This series fixes a couple of issues with the digital audio codec in the
Allwinner A64 SoC:
1) Left/right channels were swapped when playing/recording audio
2) DAPM topology was wrong, breaking some kcontrols
This is the minimum set of changes necessary to fix these issues in a
backward-compatible way. For that reason, some DAPM widgets still have
incorrect or confusing names; those and other issues will be fixed in
later patch sets.
Samuel Holland (7):
ASoC: dt-bindings: Add a new compatible for the A64 codec
ASoC: sun8i-codec: Fix DAPM to match the hardware topology
ASoC: sun8i-codec: Add missing mixer routes
ASoC: sun8i-codec: Add a quirk for LRCK inversion
ARM: dts: sun8i: a33: Update codec widget names
arm64: dts: allwinner: a64: Update codec widget names
arm64: dts: allwinner: a64: Update the audio codec compatible
.../sound/allwinner,sun8i-a33-codec.yaml | 6 +-
arch/arm/boot/dts/sun8i-a33-olinuxino.dts | 4 +-
arch/arm/boot/dts/sun8i-a33.dtsi | 4 +-
.../dts/allwinner/sun50i-a64-bananapi-m64.dts | 8 +-
.../dts/allwinner/sun50i-a64-orangepi-win.dts | 8 +-
.../boot/dts/allwinner/sun50i-a64-pine64.dts | 8 +-
.../dts/allwinner/sun50i-a64-pinebook.dts | 8 +-
.../dts/allwinner/sun50i-a64-pinephone.dtsi | 8 +-
.../boot/dts/allwinner/sun50i-a64-pinetab.dts | 8 +-
.../allwinner/sun50i-a64-sopine-baseboard.dts | 8 +-
.../boot/dts/allwinner/sun50i-a64-teres-i.dts | 8 +-
arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi | 11 +-
sound/soc/sunxi/sun8i-codec.c | 137 ++++++++++++++----
13 files changed, 155 insertions(+), 71 deletions(-)
--
2.26.2
By including the earpiece mute switch in the DAPM graph, both the
earpiece amplifier and the Mixer/DAC inputs can be powered off when
the earpiece is muted.
While the widget is really just a simple switch, it is represented
as a "mixer with named controls" to avoid including the widget name
in the kcontrol name. Otherwise, it is not possible to give the widget
an accurate, descriptive name without changing the kcontrol name
seen by userspace (which should be stable).
The mute switch is between the source selection and the amplifier,
as per the diagram in the SoC manual.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20200726025334.59931-9-samuel@sholland.org
Signed-off-by: Mark Brown <broonie@kernel.org>
By including the line out mute switch in the DAPM graph, the
Mixer/DAC inputs can be powered off when the line output is muted.
The line outputs have an unusual routing scheme. The left side mute
switch is between the source selection and the amplifier, as usual.
The right side source selection comes *after* its amplifier (and
after the left side amplifier), and its mute switch controls
whichever source is currently selected. This matches the diagram in
the SoC manual.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20200726025334.59931-8-samuel@sholland.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This matches the hardware more accurately, and is necessary for
including the (stereo) line out mute switch in the DAPM graph.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20200726025334.59931-7-samuel@sholland.org
Signed-off-by: Mark Brown <broonie@kernel.org>
By including the headphone mute switch to the DAPM graph, both the
headphone amplifier and the Mixer/DAC inputs can be powered off when
the headphones are muted.
The mute switch is between the source selection and the amplifier,
as per the diagram in the SoC manual.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20200726025334.59931-6-samuel@sholland.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This matches the hardware more accurately, and is necessary for
including the (stereo) headphone mute switch in the DAPM graph.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20200726025334.59931-5-samuel@sholland.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Sort the controls in the same order as the bits in the register. Then
group the routes by sink, and sort them in the same order as the
controls. This makes it much easier to verify that all mixer inputs are
accounted for.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20200726025334.59931-4-samuel@sholland.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The clock must be running for the zero-crossing mute functionality.
However, it must be gated for VDD-SYS to be turned off during system
suspend. Disable it in the suspend callback, after everything has
already been muted, to avoid pops when muting/unmuting outputs.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20200726025334.59931-3-samuel@sholland.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The same enable bits are currently used for both the "Left/Right ADC"
and the "Left/Right ADC Mixer" widgets. This happens to work in practice
because the widgets are always enabled/disabled at the same time, but
each register bit should only be associated with a single widget.
To keep symmetry with the DAC widgets, keep the bits on the ADC widgets,
and remove them from the ADC Mixer widgets.
Fixes: 42371f327d ("ASoC: sunxi: Add new driver for Allwinner A64 codec's analog path controls")
Reported-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20200726025334.59931-2-samuel@sholland.org
Signed-off-by: Mark Brown <broonie@kernel.org>
On the A64, as tested using the PinePhone, the current code causes the
left/right channels to be swapped during I2S playback from the CPU on
AIF1, and breaks DSP_A communication with the modem on AIF2. Both of
these are fixed when LRCK is no longer inverted.
Trusting that the comment in the code is correct, the existing behavior
is kept for the A33.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20200726012557.38282-5-samuel@sholland.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The sun8i-codec driver provides ALSA controls for enabling/disabling
each of the inputs to the AIF1 Slot 0 and DAC mixers. For two of these
inputs (ADC->DAC and AIF1 DA0->AIF1 AD0), the audio source is
implemented, so the mixer inputs can be used.
However, because the DAPM routes are missing, these mixer inputs only
work when both the source and the mixer happen to be part of other
active audio paths. Adding the appropriate routes makes these ALSA
controls function all of the time.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20200726012557.38282-4-samuel@sholland.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The A33/A64 digital codec has 4 physical inputs and 4 physical outputs:
3 AIFs/DAIs and one ADC/DAC pair. Internal routing is accomplished by
a 4-channel mixer connected to each output.
The analog and digital sides of the ADC/DAC are in separate ASoC
components, so card-level DAPM routes (provided in the device tree) are
necessary to connect them together. Currently, these routes are wrong.
For AIF1 Playback, the correct topology is:
||<<============ sun8i-codec ===========>>||
|| ||
CPU DAI -> AIF1 DA0 -> DAC Mixer -> DAC (digital) -> DAC (analog)
|| ||
but the driver and device trees currently describe:
|| ||
CPU DAI -> AIF1 DA0 -------------------------------> DAC (analog)
|| \--> DAC Mixer -> ??? [dead end] ||
For AIF1 Capture, there is an additional problem, because the Mixer
route is backward. The topology should be:
|| ||
ADC (analog) -> ADC (digital) -> AIF1 AD0 Mixer -> AIF1 AD0 -> CPU DAI
|| ||
but the driver and device trees currently describe:
|| ||
ADC (analog) -> AIF1 AD0 ------------------------------------> CPU DAI
|| \--> ADC Mixer -> ??? [dead end] ||
The ADC/DAC are only powered because AIF1 AD0 (capture) has supply
routes from the ADC, and AIF1 DA0 (playback) has supply routes from the
DAC. However, neither set of supply routes matches the hardware
topology. Audio can be routed among AIF1/2/3 without using the ADC or
DAC at all; and audio can be routed from the ADC to the DAC without
using any AIFs (via the "ADC Digital DAC Playback Switch"). Because the
DAPM routes are wrong, both of these use cases are currently broken.
This commit adds the necessary widgets and routes to represent the real
hardware topology, with functionality equivalent to the current driver.
For the existing "allwinner,sun8i-a33-codec" compatible, widgets with
the old names are kept as wrappers around the new widgets, so existing
device trees will continue to work. For "allwinner,sun50i-a64-codec",
the old widgets can be omitted, because no device trees yet use that
compatible.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20200726012557.38282-3-samuel@sholland.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Property name descriptions need to match exactly.
Fixes the following W=1 kernel build warning(s):
sound/soc/sunxi/sun4i-spdif.c:178: warning: Function parameter or
member 'reg_dac_txdata' not described in 'sun4i_spdif_quirks'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Andrea Venturi <be17068@iperbole.bo.it>
Cc: Marcus Cooper <codekipper@gmail.com>
Link: https://lore.kernel.org/r/20200709162328.259586-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix W=1 warnings - missing fields in description
sound/soc/sunxi/sun4i-i2s.c:160: warning: Function parameter or
member 'bclk_dividers' not described in 'sun4i_i2s_quirks'
sound/soc/sunxi/sun4i-i2s.c:160: warning: Function parameter or member
'num_bclk_dividers' not described in 'sun4i_i2s_quirks'
sound/soc/sunxi/sun4i-i2s.c:160: warning: Function parameter or member
'mclk_dividers' not described in 'sun4i_i2s_quirks'
sound/soc/sunxi/sun4i-i2s.c:160: warning: Function parameter or member
'num_mclk_dividers' not described in 'sun4i_i2s_quirks'
sound/soc/sunxi/sun4i-i2s.c:160: warning: Function parameter or member
'get_bclk_parent_rate' not described in 'sun4i_i2s_quirks'
sound/soc/sunxi/sun4i-i2s.c:160: warning: Function parameter or member
'get_sr' not described in 'sun4i_i2s_quirks'
sound/soc/sunxi/sun4i-i2s.c:160: warning: Function parameter or member
'get_wss' not described in 'sun4i_i2s_quirks'
sound/soc/sunxi/sun4i-i2s.c:160: warning: Function parameter or member
'set_chan_cfg' not described in 'sun4i_i2s_quirks'
sound/soc/sunxi/sun4i-i2s.c:160: warning: Function parameter or member
'set_fmt' not described in 'sun4i_i2s_quirks'
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Andrea Venturi <be17068@iperbole.bo.it>
Link: https://lore.kernel.org/r/20200709162328.259586-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This field is not used anywhere in the driver, so remove it.
Fixes: 36c684936f ("ASoC: Add sun8i digital audio codec")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20200217064250.15516-5-samuel@sholland.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the correct mask for this two-bit field. This fixes setting the DAI
data format to RIGHT_J or DSP_A.
Fixes: 36c684936f ("ASoC: Add sun8i digital audio codec")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Cc: stable@kernel.org
Link: https://lore.kernel.org/r/20200217064250.15516-7-samuel@sholland.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The last set of reworks included some fixes to change the A83t behaviour
and "fix" it.
It turns out that the controller described in the datasheet and the one
supported here are not the same, yet the A83t has the two of them, and the
one supported in the driver wasn't the one described in the datasheet.
Fix this by reintroducing the proper quirks.
Fixes: 69e450e50c ("ASoC: sun4i-i2s: Fix the LRCK period on A83t")
Fixes: bf943d5279 ("ASoC: sun4i-i2s: Fix MCLK Enable bit offset on A83t")
Fixes: 2e04fc4dbf ("ASoC: sun4i-i2s: Fix WSS and SR fields for the A83t")
Fixes: 515fcfbc77 ("ASoC: sun4i-i2s: Fix LRCK and BCLK polarity offsets on newer SoCs")
Fixes: c1d3a921d7 ("ASoC: sun4i-i2s: Fix the MCLK and BCLK dividers on newer SoCs")
Fixes: fb19739d7f ("ASoC: sun4i-i2s: Use module clock as BCLK parent on newer SoCs")
Fixes: 71137bcd0a ("ASoC: sun4i-i2s: Move the format configuration to a callback")
Fixes: d70be625f2 ("ASoC: sun4i-i2s: Move the channel configuration to a callback")
Reported-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://lore.kernel.org/r/20190827123131.29129-2-mripard@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This reverts commit 3e9acd7ac6 (ASoC: sun4i-i2s: Remove
duplicated quirks structure").
It turns out that while one I2S controller is described in the A83t
datasheet, the driver supports another, undocumented, one that has been
inherited from the older SoCs, while the documented one uses the new
design.
Fixes: 3e9acd7ac6 ("ASoC: sun4i-i2s: Remove duplicated quirks structure")
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://lore.kernel.org/r/20190827093206.17919-1-mripard@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
In addition to the I2S format, the controller also supports the DSP_*
formats.
This requires some extra care on the LRCK period calculation, since the
controller, with the PCM formats, require that the value set is no longer
the periods of LRCK for a single channel, but for all of them.
Let's add the code to deal with this, and support the DSP_A and DSP_B
formats.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://lore.kernel.org/r/5562db1ac8759f12b1b87c3258223eed629ef771.1566392800.git-series.maxime.ripard@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The LRCK period field in the FMT0 register holds the number of LRCK period
for one channel in I2S mode.
This has been hardcoded to 32, while it really should be the physical width
of the format, which creates an improper clock when using a 16bit format,
with the i2s controller as LRCK master.
Fixes: 7d2993811a ("ASoC: sun4i-i2s: Add support for H3")
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://lore.kernel.org/r/f08a0c3605cd1d79752b38d704690190183f7865.1566392800.git-series.maxime.ripard@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The clock dividers function has been using the word size to compute the
clock rate at which it's supposed to be running, but the proper formula
would be to use the physical width and / or slot width in TDM.
It doesn't make any difference at the moment since all the formats
supported have the same sample width and physical width, but it's not going
to last forever.
Fixes: 7d2993811a ("ASoC: sun4i-i2s: Add support for H3")
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://lore.kernel.org/r/41a359d9885f397e066816961e5e3236afcbe0a1.1566392800.git-series.maxime.ripard@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The channels number have been hardcoded to 2 so far, while the controller
supports more than that.
Remove the instance where it has been hardcoded to compute the BCLK
divider, and pass it through as an argument to ease further support of more
channels.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://lore.kernel.org/r/48887cf7abfaab6597db233b24d7a088a913e48a.1566242458.git-series.maxime.ripard@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The LRCK polarity "normal" polarity in the I2S/TDM specs and in the
Allwinner datasheet are not the same. In the case where the i2s controller
is being used as the LRCK master, it's pretty clear when looked at under a
scope.
Let's fix this, and add a comment to clear up as much the confusion as
possible.
Fixes: 7d2993811a ("ASoC: sun4i-i2s: Add support for H3")
Fixes: 21faaea134 ("ASoC: sun4i-i2s: Add support for A83T")
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://lore.kernel.org/r/e03fb6b2a916223070b9f18405b0ef117a452ff4.1566242458.git-series.maxime.ripard@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The LRCK and BCLK polarity offsets on newer SoCs has been
changed, yet the driver didn't take it into account for all of them.
This was taken into account for the H3, but not the A83t. This was handled
using a reg_field for the H3.
However, the value in that field will not be the same, so reg_field is not
adapted in that case. Let's change for proper calls with the regular
values.
Fixes: 21faaea134 ("ASoC: sun4i-i2s: Add support for A83T")
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://lore.kernel.org/r/9cbdde80a299288878e58225df4d7884e0301348.1566242458.git-series.maxime.ripard@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
From: Marcus Cooper <codekipper@gmail.com>
The clock division dividers have changed between the older (A10/A31) and
newer (H3, A64, etc) SoCs.
While this was addressed through an offset on some SoCs, it was missing
some dividers as well, so the support wasn't perfect. Let's introduce a
pointer in the quirk structure for the divider calculation functions to use
so we can have the proper range now.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
[Maxime: Fix the commit log, use a field in the quirk structure]
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://lore.kernel.org/r/0e5b4abf06cd3202354315201c6af44caeb20236.1566242458.git-series.maxime.ripard@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
On the first generation of Allwinner SoCs (A10-A31), the i2s controller was
using the MCLK as BCLK parent. However, this changed since the introduction
of the A83t and BCLK now uses the module clock as its parent.
Let's introduce a hook to get the parent rate and use that in our divider
calculations.
Fixes: 7d2993811a ("ASoC: sun4i-i2s: Add support for H3")
Fixes: 21faaea134 ("ASoC: sun4i-i2s: Add support for A83T")
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://lore.kernel.org/r/0b6665be216b3bd0e7bc43724818f05f3f8ee881.1566242458.git-series.maxime.ripard@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The two main generations of our I2S controller require a slightly different
format configuration, mostly because of a quite different register layout
and some additional registers being needed on the newer generation.
This used to be controlled through a bunch of booleans, however this proved
to be quite impractical, especially since a bunch of SoCs forgot to set
those parameters and therefore were broken from that point of view.
Fixes: 21faaea134 ("ASoC: sun4i-i2s: Add support for A83T")
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://lore.kernel.org/r/dc818644c3e40734e7a97247c994b1fca1c3c047.1566242458.git-series.maxime.ripard@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The two main generations of our I2S controller require a slightly different
channel configuration, mostly because of a quite different register layout
and some additional registers being needed on the newer generation.
This used to be controlled through a bunch of booleans, however this proved
to be quite impractical, especially since a bunch of SoCs forgot to set
those parameters and therefore were broken from that point of view.
Fixes: 21faaea134 ("ASoC: sun4i-i2s: Add support for A83T")
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://lore.kernel.org/r/6414463de69584e8227fa495b13aa5f4798e1f0e.1566242458.git-series.maxime.ripard@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The MCLK divider calculation is currently computing the ideal divider using
the oversample rate, the sample rate and the parent rate.
However, since we have access to the frequency is supposed to be running at
already, and as it turns out we're using it to compute the oversample rate,
we can just use the ratio between the parent rate and the MCLK rate to
simplify a bit the formula.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://lore.kernel.org/r/dcc5deb2eb650758d268bddd20f60ba58856d024.1566242458.git-series.maxime.ripard@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The BCLK divider should be calculated using the parameters that actually
make the BCLK rate: the number of channels, the sampling rate and the
sample width.
We've been using the oversample_rate previously because in the former SoCs,
the BCLK's parent is MCLK, which in turn is being used to generate the
oversample rate, so we end up with something like this:
oversample = mclk_rate / sampling_rate
bclk_div = oversample / word_size / channels
So, bclk_div = mclk_rate / sampling_rate / word_size / channels.
And this is actually better, since the oversampling ratio only plays a role
because the MCLK is its parent, not because of what BCLK is supposed to be.
Furthermore, that assumption of MCLK being the parent has been broken on
newer SoCs, so let's use the proper formula, and have the parent rate as an
argument.
Fixes: 7d2993811a ("ASoC: sun4i-i2s: Add support for H3")
Fixes: 21faaea134 ("ASoC: sun4i-i2s: Add support for A83T")
Fixes: 66ecce3325 ("ASoC: sun4i-i2s: Add compatibility with A64 codec I2S")
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://lore.kernel.org/r/c3595e3a9788c2ef2dcc30aa3c8c4953bb5cc249.1566242458.git-series.maxime.ripard@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: alsa-devel@alsa-project.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20190730181557.90391-50-swboyd@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190727150738.54764-35-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190727150738.54764-34-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190727150738.54764-33-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The A64 audio codec uses the original I2S block but the SR and
WSS computation currently assigned is for the newer block.
Fixes: 619c15f7fa (ASoC: sun4i-i2s: Change SR and WSS computation)
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Link: https://lore.kernel.org/r/20190729152130.27955-1-codekipper@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds the necessary registers and audio routes to play audio using
the Earpiece, that's supported on the A64.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20190703184814.27191-1-luca@z3ntu.xyz
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 3f780533ba ("ASoC: sunxi: sun4i-codec: don't select unnecessary
Platform")
Current ALSA SoC avoid to add duplicate component to rtd,
and this driver was selecting CPU component as Platform component.
Thus, above patch removed Platform settings from this driver,
because it assumed these are same component.
But, some CPU driver is using generic DMAEngine, in such case, both
CPU component and Platform component will have same of_node/name.
In other words, there are some components which are different but
have same of_node/name.
In such case, Card driver definitely need to select Platform even
though it is same as CPU.
It is depends on CPU driver, but is difficult to know it from Card driver.
This patch reverts above patch.
Fixes: commit 3f780533ba ("ASoC: sunxi: sun4i-codec: don't select unnecessary Platform")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ALSA SoC is now supporting "no Platform". Sound card doesn't need to
select "CPU component" as "Platform" anymore if it doesn't need
special Platform.
This patch removes such settings.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
you might feel like a deja vu to receive a bulk of changes at rc5,
and it happens again; we've got a collection of fixes for ASoC.
Most of fixes are targeted for the newly merged SOF (Sound Open
Firmware) stuff and the relevant fixes for Intel platforms.
Other than that, there are a few regression fixes for the recent
ASoC core changes and HD-audio quirk, as well as a couple of
FireWire fixes and for other ASoC codecs.
-----BEGIN PGP SIGNATURE-----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=9U0L
-----END PGP SIGNATURE-----
Merge tag 'sound-5.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"It might feel like deja vu to receive a bulk of changes at rc5, and it
happens again; we've got a collection of fixes for ASoC. Most of fixes
are targeted for the newly merged SOF (Sound Open Firmware) stuff and
the relevant fixes for Intel platforms.
Other than that, there are a few regression fixes for the recent ASoC
core changes and HD-audio quirk, as well as a couple of FireWire fixes
and for other ASoC codecs"
* tag 'sound-5.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (54 commits)
Revert "ALSA: hda/realtek - Improve the headset mic for Acer Aspire laptops"
ALSA: ice1712: Check correct return value to snd_i2c_sendbytes (EWS/DMX 6Fire)
ALSA: oxfw: allow PCM capture for Stanton SCS.1m
ALSA: firewire-motu: fix destruction of data for isochronous resources
ASoC: Intel: sst: fix kmalloc call with wrong flags
ASoC: core: Fix deadlock in snd_soc_instantiate_card()
SoC: rt274: Fix internal jack assignment in set_jack callback
ALSA: hdac: fix memory release for SST and SOF drivers
ASoC: SOF: Intel: hda: use the defined ppcap functions
ASoC: core: move DAI pre-links initiation to snd_soc_instantiate_card
ASoC: Intel: cht_bsw_rt5672: fix kernel oops with platform_name override
ASoC: Intel: cht_bsw_nau8824: fix kernel oops with platform_name override
ASoC: Intel: bytcht_es8316: fix kernel oops with platform_name override
ASoC: Intel: cht_bsw_max98090: fix kernel oops with platform_name override
ASoC: sun4i-i2s: Add offset to RX channel select
ASoC: sun4i-i2s: Fix sun8i tx channel offset mask
ASoC: max98090: remove 24-bit format support if RJ is 0
ASoC: da7219: Fix build error without CONFIG_I2C
ASoC: SOF: Intel: hda: Fix COMPILE_TEST build error
ASoC: SOF: fix DSP oops definitions in FW ABI
...
ASoC is now supporting modern style dai_link
(= snd_soc_dai_link_component) for CPU/Codec/Platform.
This patch switches to use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The current computation for the SR (sample resolution) and the WSS (word
slot size) register parameters is based on a switch returning the matching
parameters for a given params width.
Later SoCs (A83t, H3, A64) changed that calculation, which was loosely the
same with an offset. Therefore, an offset was added to adjust those
parameters.
However, the calculation is a bit less trivial than initially thought.
Indeed, while we assumed that SR and WSS were always the same, on older
SoCs, SR will max at 24 (since those SoCs do not support 32 bits formats),
but the word size can be 32.
Newer SoCs can also support a much larger range (8 bits to 32 bits, by
increments of 4) of size than the older SoCs could.
Finally, the A64 and A83t were never adjusted to have that offset in the
first place, and were therefore broken from that point of view.
In order to fix all those issues, let's introduce two functions, get_wss
and get_sr, with their respective implementations for all the SoCs
supported so far.
Fixes: 21faaea134 ("ASoC: sun4i-i2s: Add support for A83T")
Fixes: 66ecce3325 ("ASoC: sun4i-i2s: Add compatibility with A64 codec I2S")
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Whilst testing the capture functionality of the i2s on the newer
SoCs it was noticed that the recording was somewhat distorted.
This was due to the offset not being set correctly on the receiver
side.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Although not causing any noticeable issues, the mask for the
channel offset is covering too many bits.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Based on 3 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [kishon] [vijay] [abraham]
[i] [kishon]@[ti] [com] this program is distributed in the hope that
it will be useful but without any warranty without even the implied
warranty of merchantability or fitness for a particular purpose see
the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [graeme] [gregory]
[gg]@[slimlogic] [co] [uk] [author] [kishon] [vijay] [abraham] [i]
[kishon]@[ti] [com] [based] [on] [twl6030]_[usb] [c] [author] [hema]
[hk] [hemahk]@[ti] [com] this program is distributed in the hope
that it will be useful but without any warranty without even the
implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1105 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.202006027@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allwinner DAC seems to have a delay in the Speaker audio routing. When
playing a sound for the first time, the sound gets chopped. On a second
play the sound is played correctly. After some time (~5s) the issue gets
back.
This commit seems to be fixing the same issue as bf14da7 but
for another codepath.
This is the DTS that was used to debug the problem.
&codec {
allwinner,pa-gpios = <&r_pio 0 11 GPIO_ACTIVE_HIGH>; /* PL11 */
allwinner,audio-routing =
"Speaker", "LINEOUT";
status = "okay";
}
Signed-off-by: Georgii Staroselskii <georgii.staroselskii@emlid.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Allwinner H6 has a different mapping for the fifo register controller.
Actually only the fifo TX bit is used in the drivers.
Use the freshly introduced quirks to make this drivers compatible with
the Allwinner H6.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Allwinner H6 has a different bit to flush the TX FIFO.
Add a quirks to prepare introduction of H6 SoC.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The quirks are actually defines in the middle of the file with
short explanation.
Move this at the top and add a section to have coherency with
sun4i-i2s.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Based on 1 normalized pattern(s):
released under the gpl this program is free software you can
redistribute it and or modify it under the terms of the gnu general
public license as published by the free software foundation either
version 2 of the license or at your option any later version this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 2 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190523091651.124582774@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The A64 datasheet lists the supply rail for the headphone amp's charge
pump as "CPVDD". cpvdd-supply is the name of the property for this power
rail specified in the device tree bindings. "HPVCC" was the name used in
the A33 datasheet for the same function.
Rename the supply so it matches the datasheet, bindings, and the subject
from the original commit.
Fixes: ca0412a057 ("ASoC: sunxi: sun50i-codec-analog: Add support for cpvdd regulator supply")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add Line Playback Volume for Allwinner A10 and Allwinner A20.
Add Line Boost Volume for Allwinner A10 and Allwinner A20.
Add Line Right, Line Left, Line Playback Switch for Allwinner A10 and
Allwinner A20.
Signed-off-by: Danny Milosavljevic <dannym@scratchpost.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add FM Playback Volume for Allwinner A10 and Allwinner A20.
Add FM Left, FM Right, FM Playback Switch for Allwinner A10 and
Allwinner A20.
Signed-off-by: Danny Milosavljevic <dannym@scratchpost.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add Mic1 Playback Switch and Mic2 Playback Switch for Allwinner A10 and
Allwinner A20.
Signed-off-by: Danny Milosavljevic <dannym@scratchpost.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since it's now possible to have a DAPM mixer control with multiple
channels, use it to cut down the total number of controls.
Keep "Left Mixer Left DAC Playback Switch" and "Right Mixer Right DAC
Playback Switch" name & layout the same as before for compatibility.
Signed-off-by: Danny Milosavljevic <dannym@scratchpost.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add Mic1 Boost Volume and Mic2 Boost Volume for Allwinner A10 and for
Allwinner A20.
Those controls are in different registers per chip model, so put the
Allwinner A10 controls and the Allwinner A20 controls into the newly
split sun4i_codec_controls and sun7i_codec_controls, respectively.
Signed-off-by: Danny Milosavljevic <dannym@scratchpost.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Introduce sun7i_codec_controls because some of the controls are different
on Allwinner A20 compared to Allwinner A10.
Also introduce sun7i_codec_codec in order to use sun7i_codec_controls and
make sun7i_codec_quirks use sun7i_codec_codec.
Signed-off-by: Danny Milosavljevic <dannym@scratchpost.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a control "Mic Playback Volume" that allows the user to control the
MIC gain stage (common for Mic1 and Mic2) leading to the output mixer.
Signed-off-by: Danny Milosavljevic <dannym@scratchpost.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add MIC2 Pre-Amplifier, Mic2 input for Allwinner A10 and Allwinner A20.
Previously, there only the Mic1 input and MIC1 Pre-Amplifier was exposed.
This exposes the Mic2 input and MIC2 Pre-Amplifier.
Signed-off-by: Danny Milosavljevic <dannym@scratchpost.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
On the Allwinner A64 SoCs, the audio codec has a built-in headphone
amplifier. This amplifier has a power supply separate from the rest of
the analog audio circuitry, labeled cpvdd.
This patch adds a DAPM widget for this supply, and ties it to the
headphone amp widget.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
sun8i-codec misses a route from ADC to AIF1 Slot 0 ADC. Add it
to the driver to avoid adding it to every dts.
Fixes: eda85d1fee ("ASoC: sun8i-codec: Add ADC support for a33")
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
drvdata is actually sun8i_codec, not snd_soc_card, so it crashes
when calling snd_soc_card_get_drvdata().
Drop card and scodec vars anyway since we don't need to
disable/unprepare clocks - it's already done by calling
runtime_suspend()
Drop clk_disable_unprepare() calls for the same reason.
Fixes: 36c684936f ("ASoC: Add sun8i digital audio codec")
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SND_SUN50I_CODEC_ANALOG selects SND_SUNXI_ADDA_PR_REGMAP which is leftover
of renaming SND_SUNXI_ADDA_PR_REGMAP to SND_SUN8I_ADDA_PR_REGMAP. Replace
it with SND_SUN8I_ADDA_PR_REGMAP to fix possible link errors for some
configurations:
sound/soc/sunxi/sun50i-codec-analog.o: In function `sun50i_codec_analog_probe':
sun50i-codec-analog.c:(.text+0x62): undefined reference to `sun8i_adda_pr_regmap_init'
Fixes: 42371f327d ("ASoC: sunxi: Add new driver for Allwinner A64 codec's analog path controls")
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
startup() and shutdown() hooks are called for both substreams,
so stopping either substream when another is running breaks the
latter.
E.g. playback breaks if capture is stopped when playback is running.
Move code from startup() and shutdown() to resume() and suspend()
hooks respectively to fix this issue
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Allwinner A64 uses the same digital codec part as in A33, so we need
to build this driver on ARM64 as well.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The internal codec on A64 is split into 2 parts. The analog path controls
are routed through an embedded custom register bus accessed through
the PRCM block.
Add an ASoC component driver for it. This should be tied to the codec
audio card as an auxiliary device.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It will be reused by sun50i-codec-analog later.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
BCLK / LRCK ratio should be sample size * channels, but it was
hardcoded to 32 (0x1 is 32 as per A33 and A64 datasheets).
Calculate it basing on sample size and number of channels.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The I2S block used for the audio codec in the A64 differs from other 3
I2S modules in A64 and isn't compatible with H3. But it is very similar
to what is found in A10(sun4i). However, its TX FIFO is
located at a different address.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
I2S's RX slot number of SUN8I should be shifted 4 bit to left.
Fixes: 7d2993811a ("ASoC: sun4i-i2s: Add support for H3")
Signed-off-by: Yong Deng <yong.deng@magewell.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Add ADC support for the sun8i-codec driver.
This driver uses microphones widgets and routes provided by the
analog part (sun8i-codec-analog).
Some digital configurations are needed by creating new ADC widgets
and routes.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When any of the DAI hardware configuration callbacks (.hw_param,
.set_fmt, .set_sysclk) fails, there is no explanation about why it
failed. This is particularly confusing for .hw_param, which covers
many parameters of the DAI. Telling the users what parameter isn't
supported, and what the requested value was goes a long way for
developers trying to combine sun4i-i2s with external codecs.
This patch adds dev_err calls explaining what isn't supported or
failed, and what the value was. sun4i_i2s_set_clk_rate()'s first
parameter was changed to a struct snd_soc_dai *dai, so we can
get the underlying device.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
H3 ASoC supports 12Khz and 24Khz audio sample rates but the current
drivers doesn't advertise these rates properly and they cannot be used.
For example attempt to capture at 12Khz uses 11Khz (same applies to
audio playback):
Recording raw data '/tmp/testS16_LE.raw' : Signed 16 bit Little Endian, Rate 12000 Hz, Stereo
Warning: rate is not accurate (requested = 12000Hz, got = 11025Hz)
This patch fixes the audio sample rates declared and supported by the
driver according to the H3 data sheet. Specifically for audio playback:
8000, 11050, 12000, 16000, 22050, 24000, 32000, 44100, 48000, 96000, 192000
and for audio capture:
8000, 11050, 12000, 16000, 22050, 24000, 32000, 44100, 48000
Signed-off-by: Andrea Bondavalli <andrea.bondavalli74@gmail.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The I2S controller in the A83T is mostly compatible with the one found
in earlier SoCs such as the A20 and A31. While the documents publicly
available for the A83T do not cover this hardware, the officially
released BSP kernel does have register definitions for it. These were
matched against the A20 user manual. The only difference is the TX FIFO
and interrupt status registers have been swapped around, like what we
have seen with the SPDIF controller.
This patch adds support for this hardware.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
32bit and 24bit audio capture formats for H3/H2+ are broken because the
RX_SAMPLE_BITS and the RX_FIFO_MODE bits of AC_ADC_FIFOC register of the audio
codec are not set to operate in 24bit mode but in 16bit mode only.
The following patch sets the H3 audio codec registers and the DMA bus width
properly when a 24/32bit capture is requested.
Signed-off-by: Andrea Bondavalli <andrea.bondavalli74@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The current code might be a bit intriguing without having experienced the
issue before, and might come up as a mistake.
Make explicit what's going on by adding a comment.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
While the current code was reporting to be able to work in master mode, it
failed to do so because the BCLK divider wasn't programmed, meaning that
the BCLK would run at the PLL's frequency no matter the sample rate.
It was obviously a bit too fast.
Add support to retrieve the divider to use, and set it. Since our PLL is
not always able to generate a perfect multiple of the sample rate, we'll
have to choose the closest divider that matches our setup.
Fixes: 36c684936f ("ASoC: Add sun8i digital audio codec")
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
Since its introduction, the codec had an inversion of the left and right
channels. It turned out to be pretty simple as it appears that the codec
doesn't have the same polarity on the LRCK signal than the I2S block.
Fix this by inverting our bit value for the LRCK inversion.
Fixes: 36c684936f ("ASoC: Add sun8i digital audio codec")
Cc: <stable@vger.kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The current code had the condition backward when checking if the codec
should be running in slave or master mode.
Fix it, and make the comment a bit more readable.
Fixes: 36c684936f ("ASoC: Add sun8i digital audio codec")
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sun8i-h3 introduces a lot of changes to the i2s block such
as different register locations, extended clock division and
more operational modes. As we have to consider the earlier
implementation then these changes need to be isolated.
None of the new functionality has been implemented yet, the
driver has just been expanded to allow it work on the H3 SoC.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The default value of the config register is different on newer
SoCs and therefore enabling/disabling with a register write
will clear bits used to set the direction of the clock and frame
pins.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The newer SoCs do not have this setting. Instead they set the pin
direction. Add a check to see if the bit is valid and if so set
it accordingly.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
On the newer SoCs the bits to configure the operational mode are
located in a different register. Add a regmap field so that this
location can be configured.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The location of the mclk output enable bit is different on newer
SoCs. Use a regmap field to enable it.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
On newer SoCs the bit fields for the blck and lrclk polarity are in
a different locations. Use regmap fields to set the polarity bits
as intended.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
On newer SoCs the location of the slot width select and sample
resolution are different and also there is a bigger range of
support.
For the current supported rates then an offset is required.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
On the original i2s block the channel mapping and selection were
configured for stereo audio by default: This is not the case with
the newer SoCs and they are also located at different offsets.
To support the newer SoC then regmap fields have been added to the
quirks and these are initialised to their correct settings during
probing.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
First of all,the address of pdev->dev is assigned to card->dev in
create_card,then the function platform_set_drvdata copies the value
the variable card to pdev->dev.driver_data, but when calling
snd_soc_register_card,the function dev_set_drvdata(card->dev, card)
will also do the same copy operation,so i think that the former copy
operation can be removed.
Signed-off-by: Peng Donglin <dolinux.peng@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It has been seen that the newer SoCs have a different TX FIFO
address. Add this to the quirks structure.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The newer SoCs have a larger range than the original SoC that this
driver was developed for. By adding the regmap config to the quirks
then the driver can initialise the managed register map correctly.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The BCLKDIV and MCLKDIV found on newer SoCs start from an offset of 1.
Add the functionality to adjust the division values according to the
needs to the device being used.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Declare snd_soc_codec_driver structures as const as they are either
passed as an argument to the function snd_soc_register_codec or stored as
reference in field codec of type sun4i_codec_quirks. Both the fucntion
argument and the codec field are of type const, so declare the
structures with this property as const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation for the changes required to support newer SoCs then
quirks has been moved and also added to the device structure.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: alsa-devel@alsa-project.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This structure is only stored in the ops field of a snd_soc_dai_driver
structure. That field is declared const, so snd_soc_dai_ops structures
that have this property can be declared as const also.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The gpiod API checks for NULL descriptors, so there is no need to
duplicate the check in the driver.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec in the V3s is similar to the one found on the A31. One key
difference is the analog path controls are routed through the PRCM
block. This is supported by the sun8i-codec-analog driver, and tied
into this codec driver with the audio card's aux_dev.
In addition, the V3s does not have LINEIN, LINEOUT, MBIAS and MIC2,
MIC3, and the FIFO related registers are like H3.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The V3s SoC features an analog codec with headphone support but without
mic2 and linein.
Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Allwinner V3s has an analog codec without MIC2 and Line In, which will
need a special set of mixer controls/widgets/routes, otherwise meaningless
controls will be exported to userspace and confuse the user.
Add the special set, and use it when the SoC has no MIC2 and Line In.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Allwinner V3s features an analog codec without MBIAS pin.
Split out this part, in order to prepare for the V3s analog codec.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Update the driver to use SND_SOC_DAPM_AIF_IN instead of
SND_SOC_DAPM_DAC.
Rename the interface's widgets to be more precise on which slot
the interface is connected.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
An unwanted space is present in an audio widget's name on the dapm
routing. It causes an error on the recognition of this widget (error:
("no dapm match for AIF1 Slot 0 Right").
Remove the space fixes it.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
