release_firmware() checks for NULL pointers internally.
Remove unneeded NULL check for fmw here.
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://patch.msgid.link/20250407063403.2772040-1-nichen@iscas.ac.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
of_gpio.h is deprecated, update the driver to use GPIO descriptors.
- Use devm_gpiod_get_optional to get GPIO descriptor.
- Use gpiod_set_value to configure output value.
With legacy of_gpio API, the driver set GPIO value 1 to power up
AK5386, and set value 0 to power down.
Per datasheet for PDN(reset_gpio in the driver):
Power Down & Reset Mode Pin
“H”: Power up, “L”: Power down & Reset
The AK5386 must be reset once upon power-up.
There is no in-tree DTS using this codec, and the bindings does not
specify polarity. Per driver and datasheet, the GPIO polarity should be
active-high which is to power up the codec. So using GPIOD_OUT_LOW
when get the GPIO descriptor matches GPIOF_OUT_INIT_LOW when using
of_gpio API.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://patch.msgid.link/20250406010532.1212894-1-peng.fan@oss.nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
clk_disable_unprepare() already checks NULL by using IS_ERR_OR_NULL.
Remove unneeded NULL check for clk here.
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://patch.msgid.link/20250325032226.603963-1-nichen@iscas.ac.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 2fef64eec2 ("ASoC: hdmi-codec: Add a prepare hook") added a
prepare implementation. Back then the new callback was only integrated
with hdmi_codec_i2s_dai_ops (which is used by the I2S input code-path).
It was not added to hdmi_codec_spdif_dai_ops (which is used by the SPDIF
input code-path).
With commit baf616647f ("drm/connector: implement generic HDMI audio
helpers") the DRM subsystem has gained a helper framework which can be
used by HDMI controller drivers. HDMI controller drivers are often
tightly coupled with the hdmi-codec because of the so-called HDMI audio
infoframe (which is often managed by the display controller).
To allow the new DRM HDMI audio framework to work with the hdmi-codec
driver for SPDIF inputs we also need to hook up the prepare callback to
hdmi_codec_spdif_dai_ops. Just hooking into the hw_params callback would
not be enough as hw_params (is called too early and) doesn't have access
to the HDMI audio infoframe contents.
Suggested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://patch.msgid.link/20250329191433.873237-1-martin.blumenstingl@googlemail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use secs_to_jiffies() instead of msecs_to_jiffies() and avoid scaling
'delay' to milliseconds.
Since 'delay' isn't a compile-time constant, secs_to_jiffies() expands
to much simpler code compared to msecs_to_jiffies(), reducing the size
of 'snd-soc-rt5677-spi.ko' by 472 bytes.
No functional changes intended.
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Link: https://patch.msgid.link/20250405125808.302259-1-thorsten.blum@linux.dev
Signed-off-by: Mark Brown <broonie@kernel.org>
On some platforms to minimise pop and click during switching between
CTIA and OMTP headset an additional HiFi mux is used. Most common
case is that this switch is switched on by default, but on some
platforms this needs a regulator enable.
move to using mux control to enable both regulator and handle gpios,
deprecate the usage of gpio.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Christopher Obbard <christopher.obbard@linaro.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://patch.msgid.link/20250327100633.11530-6-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove confusing and unused argument in swap_gnd_mic api, the second
argument active is not really used, and always set to true in the mbhc
drivers.
The callback itself is used to toggle the gnd_mic lines when a cross
connection is detected by mbhc circuits, so there is no need of this
argument.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://patch.msgid.link/20250327100633.11530-4-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
of_gpio.h is deprecated, update the driver to use GPIO descriptors.
- Use dev_gpiod_get to get GPIO descriptor.
- Use gpiod_set_value to configure output value.
With legacy of_gpio API, the driver set gpio value 0 to assert reset,
and 1 to deassert reset. And the reset-gpios use GPIO_ACTIVE_LOW flag in
DTS, so set GPIOD_OUT_LOW when get GPIO descriptors, and set value 1 means
output low, set value 0 means output high with gpiod API.
The in-tree DTS files have the right polarity set up already so we can
expect this to "just work"
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://patch.msgid.link/20250324-wcd-gpiod-v2-3-773f67ce3b56@nxp.com
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
of_gpio.h is deprecated, update the driver to use GPIO descriptors.
- Use dev_gpiod_get to get GPIO descriptor.
- Use gpiod_set_value to configure output value.
With legacy of_gpio API, the driver set gpio value 0 to assert reset,
and 1 to deassert reset. And the reset-gpios use GPIO_ACTIVE_LOW flag in
DTS, so set GPIOD_OUT_LOW when get GPIO descriptors, and set value 1 means
output low, set value 0 means output high with gpiod API.
The in-tree DTS files have the right polarity set up already so we
can expect this to "just work".
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Steev Klimaszewski <steev@kali.org>
Link: https://patch.msgid.link/20250324-wcd-gpiod-v2-2-773f67ce3b56@nxp.com
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
of_gpio.h is deprecated, update the driver to use GPIO descriptors.
- Use dev_gpiod_get to get GPIO descriptor.
- Use gpiod_set_value to configure output value.
With legacy of_gpio API, the driver set gpio value 0 to assert reset,
and 1 to deassert reset. And the reset-gpios use GPIO_ACTIVE_LOW flag in
DTS, so set GPIOD_OUT_LOW when get GPIO descriptors, and set value 1 means
output low, set value 0 means output high with gpiod API.
The in-tree DTS files have the right polarity set up already so we
can expect this to "just work".
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://patch.msgid.link/20250324-wcd-gpiod-v2-1-773f67ce3b56@nxp.com
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Existing code only configures one of WSA_MACRO_TX0 or WSA_MACRO_TX1
paths eventhough we enable both of them. Fix this bug by adding proper
checks and rearranging some of the common code to able to allow setting
both TX0 and TX1 paths
Without this patch only one channel gets enabled in VI path instead of 2
channels. End result would be 1 channel recording instead of 2.
Fixes: 2c4066e5d4 ("ASoC: codecs: lpass-wsa-macro: add dapm widgets and route")
Cc: stable@vger.kernel.org
Co-developed-by: Manikantan R <quic_manrav@quicinc.com>
Signed-off-by: Manikantan R <quic_manrav@quicinc.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://patch.msgid.link/20250403160209.21613-3-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the VI feedback rate is set to fixed 8K, fix this by getting
the correct rate from params_rate.
Without this patch incorrect rate will be set on the VI feedback
recording resulting in rate miss match and audio artifacts.
Fixes: 2c4066e5d4 ("ASoC: codecs: lpass-wsa-macro: add dapm widgets and route")
Cc: stable@vger.kernel.org
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://patch.msgid.link/20250403160209.21613-2-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
timer_delete[_sync]() replaces del_timer[_sync](). Convert the whole tree
over and remove the historical wrapper inlines.
Conversion was done with coccinelle plus manual fixups where necessary.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
A collection of device-specific fixes that have been gathered since
the previous PR.
- A few more HD-audio quirks and fixups
- A series of Qualcomm AudioReach fixes
- Various small fixes for ASoC rt5665, WSA, SOF and Cirrus.
-----BEGIN PGP SIGNATURE-----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=fyLx
-----END PGP SIGNATURE-----
Merge tag 'sound-fix-6.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A collection of device-specific fixes that have been gathered since
the previous pull:
- A few more HD-audio quirks and fixups
- A series of Qualcomm AudioReach fixes
- Various small fixes for ASoC rt5665, WSA, SOF and Cirrus"
* tag 'sound-fix-6.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek: Fix built-in mic on another ASUS VivoBook model
ALSA: hda/realtek - Support mute led function for HP platform
ASoC: imx-card: Add NULL check in imx_card_probe()
ASoC: codecs: rt5665: Fix some error handling paths in rt5665_probe()
ASoC: q6apm-dai: make use of q6apm_get_hw_pointer
ASoC: qdsp6: q6apm-dai: fix capture pipeline overruns.
ASoC: qdsp6: q6apm-dai: set 10 ms period and buffer alignment.
ASoC: q6apm: add q6apm_get_hw_pointer helper
ASoC: q6apm-dai: schedule all available frames to avoid dsp under-runs
ASoC: SOF: hda/ptl: Move mic privacy change notification sending to a work
ALSA/hda: intel-sdw-acpi: Remove (explicitly) unused header
ALSA: hda/realtek: Enable Mute LED on HP OMEN 16 Laptop xd000xx
ALSA: hda/tas2781: Upgrade calibratd-data writing code to support Alpha and Beta dsp firmware
ASoC: qdsp6: q6asm-dai: fix q6asm_dai_compr_set_params error path
ALSA: hda/realtek: Fix built-in mic breakage on ASUS VivoBook X515JA
ASoC: sma1307: Fix error handling in sma1307_setting_loaded()
ASoC: codecs: wsa884x: Correct VI sense channel mask
ASoC: codecs: wsa883x: Correct VI sense channel mask
firmware: cs_dsp: Ensure cs_dsp_load[_coeff]() returns 0 on success
around the fallout from the new CONFIG_OBJTOOL_WERROR=y feature,
which, despite its default-off nature, increased the profile/impact
of objtool warnings:
- Improve error handling and the presentation of warnings/errors.
- Revert the new summary warning line that some test-bot tools
interpreted as new regressions.
- Fix a number of objtool warnings in various drivers, core kernel
code and architecture code. About half of them are potential
problems related to out-of-bounds accesses or potential undefined
behavior, the other half are additional objtool annotations.
- Update objtool to latest (known) compiler quirks and
objtool bugs triggered by compiler code generation
- Misc fixes
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQJFBAABCgAvFiEEBpT5eoXrXCwVQwEKEnMQ0APhK1gFAmfsRJMRHG1pbmdvQGtl
cm5lbC5vcmcACgkQEnMQ0APhK1g0YRAApiCylIv+0ucdKiDVAiI+cU7dqAggFp9h
ULcTuuCtVkfjYzIBw6y1Iw9JeYsyngYaI0VEMmLasJPt8o93K0vwBXGArXJKoMeu
UPcVS8N6+LqrHsWBXk919t1wgBZ7csgUxsCa1K47NKa3eCijrqI0N8PtcoYqKd+M
tOuyEcTCTfS0E2STv6Gpdp6VfDKms3Cn4MffLbcNWJXAsd1dwzDIG8IvAHUW9yG3
/ezVjm46thneNrRd9j/qU3mqNmhsec9NemHG7URaTznRKleWULhpmhGmcPYCh4Rj
AqGjmPtqprPELtgezeV+LIcmIm5UWF/f+0tzzBrsRy1MiY8ED2w+J51DHsLoHg8t
IfIkPyYX/zu9StXoRIwx/7C5NQqBlUfXGp6TuOOwzgbKOt+uRJOU6SnSQ06ZDwsa
l2brQ+NDfvF7EvGnvi18wIM+iqMc2jSuWl0AT94ATDuAZGCyzlmwluIYmDuLfyZM
JuYOogojt5vgHXDN6Ro3rDfK+tYckwez+Txx4oByGB3IJy75osBihtvHiYno7FgW
KXDbiAfLZ4SlfPzqxI6PPzaj3py6hG9LICEiL0U8VecC7bZ/22BZQCpdKko+/E/Y
PwlqCatqz/25U7GlsnfBISJO2VAyyUcbymvjnVXzZCi+IPAfeih6WcsTPJ96jxsa
LULLCnuvmoY=
=KkiI
-----END PGP SIGNATURE-----
Merge tag 'objtool-urgent-2025-04-01' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull objtool fixes from Ingo Molnar:
"These are objtool fixes and updates by Josh Poimboeuf, centered around
the fallout from the new CONFIG_OBJTOOL_WERROR=y feature, which,
despite its default-off nature, increased the profile/impact of
objtool warnings:
- Improve error handling and the presentation of warnings/errors
- Revert the new summary warning line that some test-bot tools
interpreted as new regressions
- Fix a number of objtool warnings in various drivers, core kernel
code and architecture code. About half of them are potential
problems related to out-of-bounds accesses or potential undefined
behavior, the other half are additional objtool annotations
- Update objtool to latest (known) compiler quirks and objtool bugs
triggered by compiler code generation
- Misc fixes"
* tag 'objtool-urgent-2025-04-01' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
objtool/loongarch: Add unwind hints in prepare_frametrace()
rcu-tasks: Always inline rcu_irq_work_resched()
context_tracking: Always inline ct_{nmi,irq}_{enter,exit}()
sched/smt: Always inline sched_smt_active()
objtool: Fix verbose disassembly if CROSS_COMPILE isn't set
objtool: Change "warning:" to "error: " for fatal errors
objtool: Always fail on fatal errors
Revert "objtool: Increase per-function WARN_FUNC() rate limit"
objtool: Append "()" to function name in "unexpected end of section" warning
objtool: Ignore end-of-section jumps for KCOV/GCOV
objtool: Silence more KCOV warnings, part 2
objtool, drm/vmwgfx: Don't ignore vmw_send_msg() for ORC
objtool: Fix STACK_FRAME_NON_STANDARD for cold subfunctions
objtool: Fix segfault in ignore_unreachable_insn()
objtool: Fix NULL printf() '%s' argument in builtin-check.c:save_argv()
objtool, lkdtm: Obfuscate the do_nothing() pointer
objtool, regulator: rk808: Remove potential undefined behavior in rk806_set_mode_dcdc()
objtool, ASoC: codecs: wcd934x: Remove potential undefined behavior in wcd934x_slim_irq_handler()
objtool, Input: cyapa - Remove undefined behavior in cyapa_update_fw_store()
objtool, panic: Disable SMAP in __stack_chk_fail()
...
A relatively large set of fixes that came in since the release, mostly
for Qualcomm platforms. The biggest block of fixes is the set from
Srini which fixes various quality and glitching issues on AudioReach
systems.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmftJp4ACgkQJNaLcl1U
h9AdNgf+IX/gRsFJ3KXTeId2Vqiac1DKBSMq5xc+LcPlgUisgE3fMj83yIUiLDTH
SAyOL0g9vP8W/VpRgwIB4P09D5zXySKk+54HsW1MoDftsh7TveGQ9QrZ6ksMGbjn
WfKGFESJUsh3s5OAPDGhQmWtlHQl//IE5kJBVbY/SwoLFl5ag5LvpTs/ky9AREo9
esgfQKprgaKUV9d8MDNX+4ZNAENoPuk/WC1VqVPtOCnec7SatvBURh3G9qDqtSk7
TmoeSEQ+9MD8AYIeY+ByG+1v3qSp0LcZWKMoOuK7QQG9gmteMA/okQpaz53FY2iP
RQ52jzbDvvblOt3KU4uJ3cYqaiLcjA==
=yiK+
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v6.15-merge-window' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v6.15
A relatively large set of fixes that came in since the release, mostly
for Qualcomm platforms. The biggest block of fixes is the set from
Srini which fixes various quality and glitching issues on AudioReach
systems.
- Support for SoundWire Bulk Register Access (BRA) protocol in core
along with Intel driver support and ASoC bits required.
- AMD driver updates and support for ACP 7.0 and 7.1 platforms
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEE+vs47OPLdNbVcHzyfBQHDyUjg0cFAmfqPDQACgkQfBQHDyUj
g0fkMhAAo5kIXK3etgyxkeGuMxY9ufJB495qkwkjN4451AhlsUXkalrUd/8XUyhU
sO/vBlc0ib8g+5PV+itHLunqWjYVC73IZA/BYZYEwgyPNZTY+jEchov7dK8Ijyx4
S45NBZjUqxStiYmdMQ1xq4BgGPdQhc7mHd206m5L+9x8QtoOCoAT5gw0zYkjWLgY
xw5xNPlEPeFISnrxdkm+LNn2d/OgTaq1rpWrD23rwTJijOatlJ/gJ1+ga05BV6ja
ymDRJRHdTnyzkjV+SsUEY+O3XfaVgDo9AORzWMqe0TJwE/NKAhq+1DvcXKV3avVY
AZMbFH3Gj7UL1oQF3r1hbpjzSKuTzB9n7h/iaJqg1XRH+sbnr/0jr/jYwgEucQ1z
Pcv6XFb0cxyxdVf5ss6NFAsfGfeggJBrQ9lvoi4EWLPaA2whCFpVKNOU0m4UkEFF
ZZN2hGDykTK84Q3jOHepKIr1/gYcBJo0iO5q8Urb/5BayioZmBmFgncEI6Hw6exU
FujEumJMS21ZIV+LYDNOb7nJpPv/dcNSotT3M8u1W87I+dgB+8h6Y4lfmLrFIb2p
5YkXH9WbRG49XGGVWRr7rRCIMpKdez0d9gnd7lNf0dGgTfpws+4hU9iDYQYatL/5
z0XXfEajfPPy2tlRAkfO8xUu3k068EhZ/Q84y9inX76jC/kfoxU=
=fe9N
-----END PGP SIGNATURE-----
Merge tag 'soundwire-6.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire
Pull soundwire updates from Vinod Koul:
- Support for SoundWire Bulk Register Access (BRA) protocol in core
along with Intel driver support and ASoC bits required
- AMD driver updates and support for ACP 7.0 and 7.1 platforms
* tag 'soundwire-6.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire: (28 commits)
soundwire: take in count the bandwidth of a prepared stream
ASoC: rt711-sdca: add DP0 support
soundwire: debugfs: add interface for BPT/BRA transfers
ASoC: SOF: Intel: hda-sdw-bpt: add CHAIN_DMA support
soundwire: intel_ace2x: add BPT send_async/wait callbacks
soundwire: intel: add BPT context definition
ASoC: SOF: Intel: hda-sdw-bpt: add helpers for SoundWire BPT DMA
soundwire: intel_auxdevice: add indirection for BPT send_async/wait
soundwire: cadence: add BTP/BRA helpers to format data
soundwire: bus: add bpt_stream pointer
soundwire: bus: add send_async/wait APIs for BPT protocol
soundwire: stream: reuse existing code for BPT stream
soundwire: stream: special-case the bus compute_params() routine
soundwire: stream: extend sdw_alloc_stream() to take 'type' parameter
soundwire: extend sdw_stream_type to BPT
soundwire: cadence: add BTP support for DP0
Documentation: driver: add SoundWire BRA description
soundwire: amd: change the log level for command response log
soundwire: slave: fix an OF node reference leak in soundwire slave device
soundwire: Use str_enable_disable-like helpers
...
Should an error occur after a successful regulator_bulk_enable() call,
regulator_bulk_disable() should be called, as already done in the remove
function.
Instead of adding an error handling path in the probe, switch from
devm_regulator_bulk_get() to devm_regulator_bulk_get_enable() and
simplify the remove function and some other places accordingly.
Finally, add a missing const when defining rt5665_supply_names to please
checkpatch and constify a few bytes.
Fixes: 33ada14a26 ("ASoC: add rt5665 codec driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://patch.msgid.link/e3c2aa1b2fdfa646752d94f4af968630c0d58248.1742629525.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
uapi:
- add mediatek tiled fourcc
- add support for notifying userspace on device wedged
new driver:
- appletbdrm: support for Apple Touchbar displays on m1/m2
- nova-core: skeleton rust driver to develop nova inside off
firmware:
- add some rust firmware pieces
rust:
- add 'LocalModule' type alias
component:
- add helper to query bound status
fbdev:
- fbtft: remove access to page->index
media:
- cec: tda998x: import driver from drm
dma-buf:
- add fast path for single fence merging
tests:
- fix lockdep warnings
atomic:
- allow full modeset on connector changes
- clarify semantics of allow_modeset and drm_atomic_helper_check
- async-flip: support on arbitary planes
- writeback: fix UAF
- Document atomic-state history
format-helper:
- support ARGB8888 to ARGB4444 conversions
buddy:
- fix multi-root cleanup
ci:
- update IGT
dp:
- support extended wake timeout
- mst: fix RAD to string conversion
- increase DPCD eDP control CAP size to 5 bytes
- add DPCD eDP v1.5 definition
- add helpers for LTTPR transparent mode
panic:
- encode QR code according to Fido 2.2
scheduler:
- add parameter struct for init
- improve job peek/pop operations
- optimise drm_sched_job struct layout
ttm:
- refactor pool allocation
- add helpers for TTM shrinker
panel-orientation:
- add a bunch of new quirks
panel:
- convert panels to multi-style functions
- edp: Add support for B140UAN04.4, BOE NV140FHM-NZ, CSW MNB601LS1-3,
LG LP079QX1-SP0V, MNE007QS3-7, STA 116QHD024002, Starry 116KHD024006,
Lenovo T14s Gen6 Snapdragon
- himax-hx83102: Add support for CSOT PNA957QT1-1, Kingdisplay
kd110n11-51ie, Starry 2082109qfh040022-50e
- visionox-r66451: use multi-style MIPI-DSI functions
- raydium-rm67200: Add driver for Raydium RM67200
- simple: Add support for BOE AV123Z7M-N17, BOE AV123Z7M-N17
- sony-td4353-jdi: Use MIPI-DSI multi-func interface
- summit: Add driver for Apple Summit display panel
- visionox-rm692e5: Add driver for Visionox RM692E5
bridge:
- pass full atomic state to various callbacks
- adv7511: Report correct capabilities
- it6505: Fix HDCP V compare
- snd65dsi86: fix device IDs
- nwl-dsi: set bridge type
- ti-sn65si83: add error recovery and set bridge type
- synopsys: add HDMI audio support
xe:
- support device-wedged event
- add mmap support for PCI memory barrier
- perf pmu integration and expose per-engien activity
- add EU stall sampling support
- GPU SVM and Xe SVM implementation
- use TTM shrinker
- add survivability mode to allow the driver to do
firmware updates in critical failure states
- PXP HWDRM support for MTL and LNL
- expose package/vram temps over hwmon
- enable DP tunneling
- drop mmio_ext abstraction
- Reject BO evcition if BO is bound to current VM
- Xe suballocator improvements
- re-use display vmas when possible
- add GuC Buffer Cache abstraction
- PCI ID update for Panther Lake and Battlemage
- Enable SRIOV for Panther Lake
- Refactor VRAM manager location
i915:
- enable extends wake timeout
- support device-wedged event
- Enable DP 128b/132b SST DSC
- FBC dirty rectangle support for display version 30+
- convert i915/xe to drm client setup
- Compute HDMI PLLS for rates not in fixed tables
- Allow DSB usage when PSR is enabled on LNL+
- Enable panel replay without full modeset
- Enable async flips with compressed buffers on ICL+
- support luminance based brightness via DPCD for eDP
- enable VRR enable/disable without full modeset
- allow GuC SLPC default strategies on MTL+ for performance
- lots of display refactoring in move to struct intel_display
amdgpu:
- add device wedged event
- support async page flips on overlay planes
- enable broadcast RGB drm property
- add info ioctl for virt mode
- OEM i2c support for RGB lights
- GC 11.5.2 + 11.5.3 support
- SDMA 6.1.3 support
- NBIO 7.9.1 + 7.11.2 support
- MMHUB 1.8.1 + 3.3.2 support
- DCN 3.6.0 support
- Add dynamic workload profile switching for GC 10-12
- support larger VBIOS sizes
- Mark gttsize parameters as deprecated
- Initial JPEG queue resset support
amdkfd:
- add KFD per process flags for setting precision
- sync pasid values between KGD and KFD
- improve GTT/VRAM handling for APUs
- fix user queue validation on GC7/8
- SDMA queue reset support
raedeon:
- rs400 hyperz fix
i2c:
- td998x: drop platform_data, split driver into media and bridge
ast:
- transmitter chip detection refactoring
- vbios display mode refactoring
- astdp: fix connection status and filter unsupported modes
- cursor handling refactoring
imagination:
- check job dependencies with sched helper
ivpu:
- improve command queue handling
- use workqueue for IRQ handling
- add support HW fault injection
- locking fixes
mgag200:
- add support for G200eH5
msm:
- dpu: add concurrent writeback support for DPU 10.x+
- use LTTPR helpers
- GPU:
- Fix obscure GMU suspend failure
- Expose syncobj timeline support
- Extend GPU devcoredump with pagetable info
- a623 support
- Fix a6xx gen1/gen2 indexed-register blocks in gpu snapshot / devcoredump
- Display:
- Add cpu-cfg interconnect paths on SM8560 and SM8650
- Introduce KMS OMMU fault handler, causing devcoredump snapshot
- Fixed error pointer dereference in msm_kms_init_aspace()
- DPU:
- Fix mode_changing handling
- Add writeback support on SM6150 (QCS615)
- Fix DSC programming in 1:1:1 topology
- Reworked hardware resource allocation, moving it to the CRTC code
- Enabled support for Concurrent WriteBack (CWB) on SM8650
- Enabled CDM blocks on all relevant platforms
- Reworked debugfs interface for BW/clocks debugging
- Clear perf params before calculating bw
- Support YUV formats on writeback
- Fixed double inclusion
- Fixed writeback in YUV formats when using cloned output, Dropped
wb2_formats_rgb
- Corrected dpu_crtc_check_mode_changed and struct dpu_encoder_virt
kerneldocs
- Fixed uninitialized variable in dpu_crtc_kickoff_clone_mode()
- DSI:
- DSC-related fixes
- Rework clock programming
- DSI PHY:
- Fix 7nm (and lower) PHY programming
- Add proper DT schema definitions for DSI PHY clocks
- HDMI:
- Rework the driver, enabling the use of the HDMI Connector framework
- Bindings:
- Added eDP PHY on SA8775P
nouveau:
- move drm_slave_encoder interface into driver
- nvkm: refactor GSP RPC
- use LTTPR helpers
mediatek:
- HDMI fixup and refinement
- add MT8188 dsc compatible
- MT8365 SoC support
panthor:
- Expose sizes of intenral BOs via fdinfo
- Fix race between reset and suspend
- Improve locking
qaic:
- Add support for AIC200
renesas:
- Fix limits in DT bindings
rockchip:
- support rk3562-mali
- rk3576: Add HDMI support
- vop2: Add new display modes on RK3588 HDMI0 up to 4K
- Don't change HDMI reference clock rate
- Fix DT bindings
- analogix_dp: add eDP support
- fix shutodnw
solomon:
- Set SPI device table to silence warnings
- Fix pixel and scanline encoding
v3d:
- handle clock
vc4:
- Use drm_exec
- Use dma-resv for wait-BO ioctl
- Remove seqno infrastructure
virtgpu:
- Support partial mappings of GEM objects
- Reserve VGA resources during initialization
- Fix UAF in virtgpu_dma_buf_free_obj()
- Add panic support
vkms:
- Switch to a managed modesetting pipeline
- Add support for ARGB8888
- fix UAf
xlnx:
- Set correct DMA segment size
- use mutex guards
- Fix error handling
- Fix docs
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEEKbZHaGwW9KfbeusDHTzWXnEhr4FAmfmA2cACgkQDHTzWXnE
hr7lKQ/+I7gmln3ka8FyKnpwG5KusDpxz3OzgUKHpzOTkXL1+vPMt0vjCKRJKE3D
zfpUTWNbwlVN0krqmUGyFIeCt8wmevBF6HvQ+GsWbiWltUj3xIlnkV0TVH84XTUo
0evrXNG9K8sLjMKjrf7yrGL53Ayoaq9IO9wtOws+FCgtykAsMR/IWLrYLpj21ZQ6
Oclhq5Cz21WRoQpzySR23s3DLi4LHri26RGKbGNh2PzxYwyP/euGW6O+ncEduNmg
vQLgUfptaM/EubJFG6jxDWZJ2ChIAUUxQuhZwt7DKqRsYIcJKcfDSUzqL95t6SYU
zewlYmeslvusoesCeTJzHaUj34yqJGsvjFPsHFUEvAy8BVncsqS40D6mhrRMo5nD
chnSJu+IpDOEEqcdbb1J73zKLw6X3GROM8qUQEThJBD2yTsOdw9d0HXekMDMBXSi
NayKvXfsBV19rI74FYnRCzHt8BVVANh5qJNnR5RcnPZ2KzHQbV0JFOA9YhxE8vFU
GWkFWKlpAQUQ+yoTy1kuO9dcUxLIC7QseMeS5BYhcJBMEV78xQuRYRxgsL8YS4Yg
rIhcb3mZwMFj7jBAqfpLKWiI+GTup+P9vcz7Bvm5iIf8gEhZLUTwqBeAYXQkcWd4
i1AqDuFR0//sAgODoeU2sg1Q3yTL/i/DhcwvCIPgcDZ/x4Eg868=
=oK/N
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2025-03-28' of https://gitlab.freedesktop.org/drm/kernel
Pull drm updates from Dave Airlie:
"Outside of drm there are some rust patches from Danilo who maintains
that area in here, and some pieces for drm header check tests.
The major things in here are a new driver supporting the touchbar
displays on M1/M2, the nova-core stub driver which is just the vehicle
for adding rust abstractions and start developing a real driver inside
of.
xe adds support for SVM with a non-driver specific SVM core
abstraction that will hopefully be useful for other drivers, along
with support for shrinking for TTM devices. I'm sure xe and AMD
support new devices, but the pipeline depth on these things is hard to
know what they end up being in the marketplace!
uapi:
- add mediatek tiled fourcc
- add support for notifying userspace on device wedged
new driver:
- appletbdrm: support for Apple Touchbar displays on m1/m2
- nova-core: skeleton rust driver to develop nova inside off
firmware:
- add some rust firmware pieces
rust:
- add 'LocalModule' type alias
component:
- add helper to query bound status
fbdev:
- fbtft: remove access to page->index
media:
- cec: tda998x: import driver from drm
dma-buf:
- add fast path for single fence merging
tests:
- fix lockdep warnings
atomic:
- allow full modeset on connector changes
- clarify semantics of allow_modeset and drm_atomic_helper_check
- async-flip: support on arbitary planes
- writeback: fix UAF
- Document atomic-state history
format-helper:
- support ARGB8888 to ARGB4444 conversions
buddy:
- fix multi-root cleanup
ci:
- update IGT
dp:
- support extended wake timeout
- mst: fix RAD to string conversion
- increase DPCD eDP control CAP size to 5 bytes
- add DPCD eDP v1.5 definition
- add helpers for LTTPR transparent mode
panic:
- encode QR code according to Fido 2.2
scheduler:
- add parameter struct for init
- improve job peek/pop operations
- optimise drm_sched_job struct layout
ttm:
- refactor pool allocation
- add helpers for TTM shrinker
panel-orientation:
- add a bunch of new quirks
panel:
- convert panels to multi-style functions
- edp: Add support for B140UAN04.4, BOE NV140FHM-NZ, CSW MNB601LS1-3,
LG LP079QX1-SP0V, MNE007QS3-7, STA 116QHD024002, Starry
116KHD024006, Lenovo T14s Gen6 Snapdragon
- himax-hx83102: Add support for CSOT PNA957QT1-1, Kingdisplay
kd110n11-51ie, Starry 2082109qfh040022-50e
- visionox-r66451: use multi-style MIPI-DSI functions
- raydium-rm67200: Add driver for Raydium RM67200
- simple: Add support for BOE AV123Z7M-N17, BOE AV123Z7M-N17
- sony-td4353-jdi: Use MIPI-DSI multi-func interface
- summit: Add driver for Apple Summit display panel
- visionox-rm692e5: Add driver for Visionox RM692E5
bridge:
- pass full atomic state to various callbacks
- adv7511: Report correct capabilities
- it6505: Fix HDCP V compare
- snd65dsi86: fix device IDs
- nwl-dsi: set bridge type
- ti-sn65si83: add error recovery and set bridge type
- synopsys: add HDMI audio support
xe:
- support device-wedged event
- add mmap support for PCI memory barrier
- perf pmu integration and expose per-engien activity
- add EU stall sampling support
- GPU SVM and Xe SVM implementation
- use TTM shrinker
- add survivability mode to allow the driver to do firmware updates
in critical failure states
- PXP HWDRM support for MTL and LNL
- expose package/vram temps over hwmon
- enable DP tunneling
- drop mmio_ext abstraction
- Reject BO evcition if BO is bound to current VM
- Xe suballocator improvements
- re-use display vmas when possible
- add GuC Buffer Cache abstraction
- PCI ID update for Panther Lake and Battlemage
- Enable SRIOV for Panther Lake
- Refactor VRAM manager location
i915:
- enable extends wake timeout
- support device-wedged event
- Enable DP 128b/132b SST DSC
- FBC dirty rectangle support for display version 30+
- convert i915/xe to drm client setup
- Compute HDMI PLLS for rates not in fixed tables
- Allow DSB usage when PSR is enabled on LNL+
- Enable panel replay without full modeset
- Enable async flips with compressed buffers on ICL+
- support luminance based brightness via DPCD for eDP
- enable VRR enable/disable without full modeset
- allow GuC SLPC default strategies on MTL+ for performance
- lots of display refactoring in move to struct intel_display
amdgpu:
- add device wedged event
- support async page flips on overlay planes
- enable broadcast RGB drm property
- add info ioctl for virt mode
- OEM i2c support for RGB lights
- GC 11.5.2 + 11.5.3 support
- SDMA 6.1.3 support
- NBIO 7.9.1 + 7.11.2 support
- MMHUB 1.8.1 + 3.3.2 support
- DCN 3.6.0 support
- Add dynamic workload profile switching for GC 10-12
- support larger VBIOS sizes
- Mark gttsize parameters as deprecated
- Initial JPEG queue resset support
amdkfd:
- add KFD per process flags for setting precision
- sync pasid values between KGD and KFD
- improve GTT/VRAM handling for APUs
- fix user queue validation on GC7/8
- SDMA queue reset support
raedeon:
- rs400 hyperz fix
i2c:
- td998x: drop platform_data, split driver into media and bridge
ast:
- transmitter chip detection refactoring
- vbios display mode refactoring
- astdp: fix connection status and filter unsupported modes
- cursor handling refactoring
imagination:
- check job dependencies with sched helper
ivpu:
- improve command queue handling
- use workqueue for IRQ handling
- add support HW fault injection
- locking fixes
mgag200:
- add support for G200eH5
msm:
- dpu: add concurrent writeback support for DPU 10.x+
- use LTTPR helpers
- GPU:
- Fix obscure GMU suspend failure
- Expose syncobj timeline support
- Extend GPU devcoredump with pagetable info
- a623 support
- Fix a6xx gen1/gen2 indexed-register blocks in gpu snapshot /
devcoredump
- Display:
- Add cpu-cfg interconnect paths on SM8560 and SM8650
- Introduce KMS OMMU fault handler, causing devcoredump snapshot
- Fixed error pointer dereference in msm_kms_init_aspace()
- DPU:
- Fix mode_changing handling
- Add writeback support on SM6150 (QCS615)
- Fix DSC programming in 1:1:1 topology
- Reworked hardware resource allocation, moving it to the CRTC code
- Enabled support for Concurrent WriteBack (CWB) on SM8650
- Enabled CDM blocks on all relevant platforms
- Reworked debugfs interface for BW/clocks debugging
- Clear perf params before calculating bw
- Support YUV formats on writeback
- Fixed double inclusion
- Fixed writeback in YUV formats when using cloned output, Dropped
wb2_formats_rgb
- Corrected dpu_crtc_check_mode_changed and struct dpu_encoder_virt
kerneldocs
- Fixed uninitialized variable in dpu_crtc_kickoff_clone_mode()
- DSI:
- DSC-related fixes
- Rework clock programming
- DSI PHY:
- Fix 7nm (and lower) PHY programming
- Add proper DT schema definitions for DSI PHY clocks
- HDMI:
- Rework the driver, enabling the use of the HDMI Connector
framework
- Bindings:
- Added eDP PHY on SA8775P
nouveau:
- move drm_slave_encoder interface into driver
- nvkm: refactor GSP RPC
- use LTTPR helpers
mediatek:
- HDMI fixup and refinement
- add MT8188 dsc compatible
- MT8365 SoC support
panthor:
- Expose sizes of intenral BOs via fdinfo
- Fix race between reset and suspend
- Improve locking
qaic:
- Add support for AIC200
renesas:
- Fix limits in DT bindings
rockchip:
- support rk3562-mali
- rk3576: Add HDMI support
- vop2: Add new display modes on RK3588 HDMI0 up to 4K
- Don't change HDMI reference clock rate
- Fix DT bindings
- analogix_dp: add eDP support
- fix shutodnw
solomon:
- Set SPI device table to silence warnings
- Fix pixel and scanline encoding
v3d:
- handle clock
vc4:
- Use drm_exec
- Use dma-resv for wait-BO ioctl
- Remove seqno infrastructure
virtgpu:
- Support partial mappings of GEM objects
- Reserve VGA resources during initialization
- Fix UAF in virtgpu_dma_buf_free_obj()
- Add panic support
vkms:
- Switch to a managed modesetting pipeline
- Add support for ARGB8888
- fix UAf
xlnx:
- Set correct DMA segment size
- use mutex guards
- Fix error handling
- Fix docs"
* tag 'drm-next-2025-03-28' of https://gitlab.freedesktop.org/drm/kernel: (1762 commits)
drm/amd/pm: Update feature list for smu_v13_0_6
drm/amdgpu: Add parameter documentation for amdgpu_sync_fence
drm/amdgpu/discovery: optionally use fw based ip discovery
drm/amdgpu/discovery: use specific ip_discovery.bin for legacy asics
drm/amdgpu/discovery: check ip_discovery fw file available
drm/amd/pm: Remove unnecessay UQ10 to UINT conversion
drm/amd/pm: Remove unnecessay UQ10 to UINT conversion
drm/amdgpu/sdma_v4_4_2: update VM flush implementation for SDMA
drm/amdgpu: Optimize VM invalidation engine allocation and synchronize GPU TLB flush
drm/amd/amdgpu: Increase max rings to enable SDMA page ring
drm/amdgpu: Decode deferred error type in gfx aca bank parser
drm/amdgpu/gfx11: Add Cleaner Shader Support for GFX11.5 GPUs
drm/amdgpu/mes: clean up SDMA HQD loop
drm/amdgpu/mes: enable compute pipes across all MEC
drm/amdgpu/mes: drop MES 10.x leftovers
drm/amdgpu/mes: optimize compute loop handling
drm/amdgpu/sdma: guilty tracking is per instance
drm/amdgpu/sdma: fix engine reset handling
drm/amdgpu: remove invalid usage of sched.ready
drm/amdgpu: add cleaner shader trace point
...
We've received lots of commits at this time, as a result of various
cleanup and refactoring works as well as a few new drivers and the
generic SoundWire support. Most of changes are device-specific,
little about the core changes. Some highlights below:
Core:
* A couple of (rather minor) race fixes in ALSA sequencer code
* A regression fix in ALSA timer code that may lead to a deadlock
ASoC:
* A large series of code conversion to use modern terminology for the
clocking configuration
* Conversions of PM ops with the modern macros in all ASoC drivers
* Clarification of the control operations
* Prepartory work for more generic SoundWire SCDA controls
* Support for AMD ACP 7.x, AWINC WM88166, Everest ES8388, Intel AVS
PEAKVOL and GAIN DSP modules Mediatek MT8188 DMIC, NXP i.MX95,
nVidia Tegra interconnects, Rockchip RK3588 S/PDIF, Texas
Instruments SN012776 and TAS5770L, and Wolfson WM8904 DMICs
Others:
* Conversions of PM ops with the modern macros in the rest drivers
* USB-audio quirks and fixes for Presonus Studio, DJM-A9, CME
* HD-audio quirks and fixes ASUS, HP, Lenovo, and others
Note that the PR contains some changes from the tip tree for AMD code,
and it might give some merge conflict due to the rebase afterwards.
-----BEGIN PGP SIGNATURE-----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=NaAN
-----END PGP SIGNATURE-----
Merge tag 'sound-6.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"We've received lots of commits at this time, as a result of various
cleanup and refactoring works as well as a few new drivers and the
generic SoundWire support. Most of changes are device-specific, little
about the core changes. Some highlights below:
Core:
- A couple of (rather minor) race fixes in ALSA sequencer code
- A regression fix in ALSA timer code that may lead to a deadlock
ASoC:
- A large series of code conversion to use modern terminology for the
clocking configuration
- Conversions of PM ops with the modern macros in all ASoC drivers
- Clarification of the control operations
- Prepartory work for more generic SoundWire SCDA controls
- Support for AMD ACP 7.x, AWINC WM88166, Everest ES8388, Intel AVS
PEAKVOL and GAIN DSP modules Mediatek MT8188 DMIC, NXP i.MX95,
nVidia Tegra interconnects, Rockchip RK3588 S/PDIF, Texas
Instruments SN012776 and TAS5770L, and Wolfson WM8904 DMICs
Others:
- Conversions of PM ops with the modern macros in the rest drivers
- USB-audio quirks and fixes for Presonus Studio, DJM-A9, CME
- HD-audio quirks and fixes ASUS, HP, Lenovo, and others"
* tag 'sound-6.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (651 commits)
ALSA: hda: tas2781-i2c: Remove unnecessary NULL check before release_firmware()
ALSA: hda: cs35l56: Remove unnecessary NULL check before release_firmware()
ALSA: hda/realtek: Bass speaker fixup for ASUS UM5606KA
ALSA: hda/realtek: Fix built-in mic assignment on ASUS VivoBook X515UA
ALSA: hda/realtek: Add support for various HP Laptops using CS35L41 HDA
ALSA: timer: Don't take register_mutex with copy_from/to_user()
ASoC: SDCA: Correct handling of selected mode DisCo property
ASoC: amd: yc: update quirk data for new Lenovo model
ALSA: hda/realtek: fix micmute LEDs on HP Laptops with ALC3247
ALSA: hda/realtek: fix micmute LEDs on HP Laptops with ALC3315
ASoC: SOF: mediatek: Commonize duplicated functions
ASoC: dmic: Fix NULL pointer dereference
ASoC: wm8904: add DMIC support
ASoC: wm8904: get platform data from DT
ASoC: dt-bindings: wm8904: Add DMIC, GPIO, MIC and EQ support
ASoC: wm8904: Don't touch GPIO configs set to 0xFFFF
of: Add of_property_read_u16_index
ALSA: oxygen: Fix dependency on CONFIG_PM_SLEEP
ASoC: ops: Apply platform_max after deciding control type
ASoC: ops: Remove some unnecessary local variables
...
Merge series from Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>:
VI sense port on WSA883x and WSA884x speaker takes only one channel, so
correct the mask. At least this works during my tests on different
devices with both speakers. With original mask (0x3) I get
noise/garbage.
There are a couple bugs in this code:
1) The cleanup code calls kfree(sma1307->set.header) and
kfree(sma1307->set.def) but those functions were allocated using
devm_kzalloc(). It results in a double free. Delete all these
kfree() calls.
2) A missing call to kfree(data) if the checksum was wrong on this error
path:
if ((sma1307->set.checksum >> 8) != SMA1307_SETTING_CHECKSUM) {
Since the "data" pointer is supposed to be freed on every return, I
changed that to use the __free(kfree) cleanup attribute.
Fixes: 0ec6bd1670 ("ASoC: sma1307: Add NULL check in sma1307_setting_loaded()")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://patch.msgid.link/8d32dd96-1404-4373-9b6c-c612a9c18c4c@stanley.mountain
Signed-off-by: Mark Brown <broonie@kernel.org>
VI sense port on WSA883x speaker takes only one channel, so use 0x1 as
channel mask. This fixes garbage being recorded by the speaker when
testing the VI sense feedback path.
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20250312-asoc-wsa88xx-visense-v1-2-9ca705881122@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
VI sense port on WSA883x speaker takes only one channel, so use 0x1 as
channel mask. This fixes garbage being recorded by the speaker when
testing the VI sense feedback path.
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20250312-asoc-wsa88xx-visense-v1-1-9ca705881122@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Another set of improvements to the kernel's CRC (cyclic redundancy
check) code:
- Rework the CRC64 library functions to be directly optimized, like what
I did last cycle for the CRC32 and CRC-T10DIF library functions.
- Rewrite the x86 PCLMULQDQ-optimized CRC code, and add VPCLMULQDQ
support and acceleration for crc64_be and crc64_nvme.
- Rewrite the riscv Zbc-optimized CRC code, and add acceleration for
crc_t10dif, crc64_be, and crc64_nvme.
- Remove crc_t10dif and crc64_rocksoft from the crypto API, since they
are no longer needed there.
- Rename crc64_rocksoft to crc64_nvme, as the old name was incorrect.
- Add kunit test cases for crc64_nvme and crc7.
- Eliminate redundant functions for calculating the Castagnoli CRC32,
settling on just crc32c().
- Remove unnecessary prompts from some of the CRC kconfig options.
- Further optimize the x86 crc32c code.
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQSacvsUNc7UX4ntmEPzXCl4vpKOKwUCZ+CGGhQcZWJpZ2dlcnNA
Z29vZ2xlLmNvbQAKCRDzXCl4vpKOK3wRAP4tbnzawUmlIHIF0hleoADXehUgAhMt
NZn15mGvyiuwIQEA8W9qvnLdFXZkdxhxAEvDDFjyrRauL6eGtr/GvCx4AQY=
=wmKG
-----END PGP SIGNATURE-----
Merge tag 'crc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiggers/linux
Pull CRC updates from Eric Biggers:
"Another set of improvements to the kernel's CRC (cyclic redundancy
check) code:
- Rework the CRC64 library functions to be directly optimized, like
what I did last cycle for the CRC32 and CRC-T10DIF library
functions
- Rewrite the x86 PCLMULQDQ-optimized CRC code, and add VPCLMULQDQ
support and acceleration for crc64_be and crc64_nvme
- Rewrite the riscv Zbc-optimized CRC code, and add acceleration for
crc_t10dif, crc64_be, and crc64_nvme
- Remove crc_t10dif and crc64_rocksoft from the crypto API, since
they are no longer needed there
- Rename crc64_rocksoft to crc64_nvme, as the old name was incorrect
- Add kunit test cases for crc64_nvme and crc7
- Eliminate redundant functions for calculating the Castagnoli CRC32,
settling on just crc32c()
- Remove unnecessary prompts from some of the CRC kconfig options
- Further optimize the x86 crc32c code"
* tag 'crc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiggers/linux: (36 commits)
x86/crc: drop the avx10_256 functions and rename avx10_512 to avx512
lib/crc: remove unnecessary prompt for CONFIG_CRC64
lib/crc: remove unnecessary prompt for CONFIG_LIBCRC32C
lib/crc: remove unnecessary prompt for CONFIG_CRC8
lib/crc: remove unnecessary prompt for CONFIG_CRC7
lib/crc: remove unnecessary prompt for CONFIG_CRC4
lib/crc7: unexport crc7_be_syndrome_table
lib/crc_kunit.c: update comment in crc_benchmark()
lib/crc_kunit.c: add test and benchmark for crc7_be()
x86/crc32: optimize tail handling for crc32c short inputs
riscv/crc64: add Zbc optimized CRC64 functions
riscv/crc-t10dif: add Zbc optimized CRC-T10DIF function
riscv/crc32: reimplement the CRC32 functions using new template
riscv/crc: add "template" for Zbc optimized CRC functions
x86/crc: add ANNOTATE_NOENDBR to suppress objtool warnings
x86/crc32: improve crc32c_arch() code generation with clang
x86/crc64: implement crc64_be and crc64_nvme using new template
x86/crc-t10dif: implement crc_t10dif using new template
x86/crc32: implement crc32_le using new template
x86/crc: add "template" for [V]PCLMULQDQ based CRC functions
...
If 'port_id' is negative, the shift counts in wcd934x_slim_irq_handler()
also become negative, resulting in undefined behavior due to shift out
of bounds.
If I'm reading the code correctly, that appears to be not possible, but
with KCOV enabled, Clang's range analysis isn't always able to determine
that and generates undefined behavior.
As a result the code generation isn't optimal, and undefined behavior
should be avoided regardless. Improve code generation and remove the
undefined behavior by converting the signed variables to unsigned.
Fixes the following warning with UBSAN:
sound/soc/codecs/snd-soc-wcd934x.o: warning: objtool: .text.wcd934x_slim_irq_handler: unexpected end of section
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Mark Brown <broonie@kernel.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://lore.kernel.org/r/7e863839ec7301bf9c0f429a03873d44e484c31c.1742852847.git.jpoimboe@kernel.org
Closes: https://lore.kernel.org/oe-kbuild-all/202503180044.oH9gyPeg-lkp@intel.com/
This is a very big release due to a combination of some big new work,
mainly new drivers and generic SoundWire support, and some wide ranging
cleanup work that made small changes to a lot of drivers.
- Morimoto-san has completed the conversion to use modern terminology
for the clocking configuration, and several other cleanups with
narrower impact.
- All the power management operation configuration was updated to use
current idioms by Takashi Iwai.
- Clarification of the control operations from Charles Keepax.
- Prepartory work for more generic SoundWire SCDA controls from Charles
Keepax.
- Support for AMD ACP 7.x, AWINC WM88166, Everest ES8388, Intel AVS
PEAKVOL and GAIN DSP modules Mediatek MT8188 DMIC, NXP i.MX95, nVidia
Tegra interconnects, Rockchip RK3588 S/PDIF, Texas Instruments
SN012776 and TAS5770L, and Wolfson WM8904 DMICs,
Some changes from the tip tree adding APIs needed by the AMD code are
included, these were unfortunately rebased in the tip tree after being
pulled in. There's also some regmap changes supporting the SCDA work
and some devres refactoring that was pulled in to support other changes.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmfhZEUACgkQJNaLcl1U
h9DQjgf9FxqmX7qAbT3tV06lX6UJ79KtCGquvVpToxP3nMFa05h/HSJlQAnqEFkL
AUdAr/bfH6noDIqL08j+DMHs85lz6fP06PubCmQCHEk+yAEPOZ19OUsTKbhdXcG2
GTObvLEjnz8MDnUW99SwoB52y3DX/7F09uhcbv+xiLIZo0EmQOcTsLKx79XwuzgU
q52mQBXYi7CDhVTlnITeapcLj7G+6r2m7zLsQRWa897bKp/nRVq08GhWu0SHBNtP
m/RwBvwPZEgCDxH+aHOWvc6S7yQpotC9EIvTUchxFGkcHh9OKoLUoWLH7p+d99B2
ydVWgOz72GwRhAjp9FHH7X49A5UMmg==
=xZD3
-----END PGP SIGNATURE-----
Merge tag 'asoc-v6.15' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v6.15
This is a very big release due to a combination of some big new work,
mainly new drivers and generic SoundWire support, and some wide ranging
cleanup work that made small changes to a lot of drivers.
- Morimoto-san has completed the conversion to use modern terminology
for the clocking configuration, and several other cleanups with
narrower impact.
- All the power management operation configuration was updated to use
current idioms by Takashi Iwai.
- Clarification of the control operations from Charles Keepax.
- Prepartory work for more generic SoundWire SCDA controls from Charles
Keepax.
- Support for AMD ACP 7.x, AWINC WM88166, Everest ES8388, Intel AVS
PEAKVOL and GAIN DSP modules Mediatek MT8188 DMIC, NXP i.MX95, nVidia
Tegra interconnects, Rockchip RK3588 S/PDIF, Texas Instruments
SN012776 and TAS5770L, and Wolfson WM8904 DMICs,
Some changes from the tip tree adding APIs needed by the AMD code are
included, these were unfortunately rebased in the tip tree after being
pulled in. There's also some regmap changes supporting the SCDA work
and some devres refactoring that was pulled in to support other changes.
Merge series from Francesco Dolcini <francesco@dolcini.it>:
This patch series adds DMIC and DRC support to the WM8904 driver, a new
of_ helper is added to simplify the driver code.
DRC functionality is added in the same patch series to provide the
necessary dynamic range control to make DMIC support useful.
The WM8904 supports digital microphones on two of its inputs:
IN1L/DMICDAT1 and IN1R/DMICDAT2. These two inputs can either be
connected to an ADC or to the DMIC system. There is an ADC for each
line, and only one DMIC block. This DMIC block is either connected to
DMICDAT1 or to DMICDAT2. One DMIC data line supports two digital
microphones via time multiplexing.
The pin's functionality is decided during hardware design (IN1L vs
DMICDAT1 and IN1R vs DMICDAT2). This is reflected in the Device Tree.
If one line is analog and one is DMIC, we need to be able to switch
between ADC and DMIC at runtime. The DMIC source is known from the
Device Tree. If both are DMIC inputs, we need to be able to switch the
DMIC source. There is no need to switch between ADC and DMIC at runtime.
Therefore, kcontrols are dynamically added by the driver depending on
its Device Tree configuration.
This is a heavy rework of a previous patch series provided by Alifer
Moraes and Pierluigi Passaro,
https://lore.kernel.org/lkml/20220307141041.27538-1-alifer.m@variscite.com.
Merge series from Charles Keepax <ckeepax@opensource.cirrus.com>:
There is a lot of duplicated and occasionally slightly incorrect code
around the ASoC control get and put handlers. This series add some kunit
tests and then refactors the code to get all the tests passing and
reduce some of the duplication. The focus here is on the volsw handlers,
future work could still be done on some of the others but these were the
ones that most required attention.
Hopefully the only slightly controversal change is the very last patch
which changes platform_max to be applied after the control type is
determined, more discussion in the commit message for that one.
The WM8904 codec supports both ADC and DMIC inputs.
Get input pin functionality from the platform data and add the necessary
controls depending on the possible additional routing.
The ADC and DMIC share the IN1L/DMICDAT1 and IN1R/DMICDAT2 pins.
This leads to a few scenarios requiring different DAPM routing:
- When both are connected to an analog input, only the ADC is used.
- When one line is a DMIC and the other an analog input, the DMIC source
is set from the platform data and a mux is added to select whether to
use the ADC or DMIC.
- When both are connected to a DMIC, another mux is added to this to
select the DMIC source. Note that we still need to be able to select
the ADC system for use with the IN2L, IN2R, IN3L and IN3R pins.
Signed-off-by: Ernest Van Hoecke <ernest.vanhoecke@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250319142059.46692-6-francesco@dolcini.it
Signed-off-by: Mark Brown <broonie@kernel.org>
Read in optional codec-specific properties from the device tree.
The platform_data structure is not populated when using device trees.
This change parses optional dts properties to populate it.
- wlf,in1l-as-dmicdat1
- wlf,in1r-as-dmicdat2
- wlf,gpio-cfg
- wlf,micbias-cfg
- wlf,drc-cfg-regs
- wlf,drc-cfg-names
- wlf,retune-mobile-cfg-regs
- wlf,retune-mobile-cfg-names
- wlf,retune-mobile-cfg-hz
Datasheet: https://statics.cirrus.com/pubs/proDatasheet/WM8904_Rev4.1.pdf
Signed-off-by: Ernest Van Hoecke <ernest.vanhoecke@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250319142059.46692-5-francesco@dolcini.it
Signed-off-by: Mark Brown <broonie@kernel.org>
When updating the GPIO registers, do nothing for all fields of gpio_cfg
that are "0xFFFF".
This "do nothing" flag used to be 0 to easily check whether the gpio_cfg
field was actually set inside pdata or left empty (default).
However, 0 is a valid configuration for these registers, while 0xFFFF is
not.
With this change, users can explicitly set them to 0.
Not setting gpio_cfg in the platform data will now lead to setting all
GPIO registers to 0 instead of leaving them unset.
No one is using this platform data with this codec.
The change gets the driver ready to properly set gpio_cfg from the DT.
Datasheet: https://statics.cirrus.com/pubs/proDatasheet/WM8904_Rev4.1.pdf
Signed-off-by: Ernest Van Hoecke <ernest.vanhoecke@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250319142059.46692-3-francesco@dolcini.it
Signed-off-by: Mark Brown <broonie@kernel.org>
irq_domain_add_linear() is going away as being obsolete now. Switch to
the preferred irq_domain_create_linear(). That differs in the first
parameter: It takes more generic struct fwnode_handle instead of struct
device_node. Therefore, of_fwnode_handle() is added around the
parameter.
Note some of the users can likely use dev->fwnode directly instead of
indirect of_fwnode_handle(dev->of_node). But dev->fwnode is not
guaranteed to be set for all, so this has to be investigated on case to
case basis (by people who can actually test with the HW).
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
Cc: linux-sound@vger.kernel.org
Link: https://patch.msgid.link/20250319092951.37667-36-jirislaby@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
With the addition of the soc_mixer_ctl_to_reg() helper it is now very
clear that the only difference between snd_soc_put_volsw() and
snd_soc_put_volsw_range() is that the former supports double controls
with both values in the same register. As such we can combine both
functions.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250318171459.3203730-11-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
With the addition of the soc_mixer_reg_to_ctl() helper it is now very
clear that the only difference between snd_soc_get_volsw() and
snd_soc_get_volsw_range() is that the former supports double controls
with both values in the same register. As such we can combine both
functions.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250318171459.3203730-10-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
For calibration, basic version does not contain any calibration addresses,
it depends on calibration tool to convey the addresses to the driver.
Since Alpha and Beta firmware, all the calibration addresses are saved
into the firmware.
Signed-off-by: Shenghao Ding <shenghao-ding@ti.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20250313093238.1184-1-shenghao-ding@ti.com
Back-merge of 6.14 devel branch for further developments of TAS
codecsBack-merge of 6.14 devel branch for further developments.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Merge series from wangweidong.a@awinic.com:
Add the awinic,aw88166 property to support the aw88166 chip.
The driver is for amplifiers aw88166 of Awinic Technology
Corporation. The AW88166 is a high efficiency digital
Smart K audio amplifier
Merge series from Takashi Iwai <tiwai@suse.de>:
This is a revised series of small and trivial patches to convert to
the newer PM macros, e.g. from SET_RUNTIME_PM_OPS() to
RUNTIME_PM_OPS().
The conversions are systematic, and we could reduce messy
__maybe_unused and ifdefs with those changes.
Merely code refactoring, and shouldn't change the actual driver
behavior.
Merge series from Linus Walleij <linus.walleij@linaro.org>:
Three remaining TI PCM codecs use the old GPIO API in
different ways, fix them all up and move over to
<linux/gpio/consumer.h> and get rid of <linux/gpio.h>.
Merge series from "Nícolas F. R. A. Prado" <nfraprado@collabora.com>:
This series enables the MT8188-MT6359 sound driver to retrieve the
MT6359 ACCDET sound component from a mediatek,accdet DT property, which
allows detecting jack insertion/removal.
Patch 1 describes the new property in the binding. Patch 2 implements
the sound component retrieval in the common MTK soundcard driver. Patch
4 updates the MT8188-MT6359 sound driver to register the audio jack and
initialize the ACCDET driver for detection, if the property is present.
Patch 3 adds a stub to prevent a linker failure in case the
MT6359-ACCDET config is disabled.
Tested on the Genio 700 EVK board.
Use the newer EXPORT_GPL_DEV_PM_OPS() macro together with pm_ptr(),
which allows us to drop superfluous CONFIG_PM ifdefs.
This optimizes slightly when CONFIG_PM is disabled, too.
Cc: Shenghao Ding <shenghao-ding@ti.com>
Cc: Kevin Lu <kevin-lu@ti.com>
Cc: Baojun Xu <baojun.xu@ti.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250317095603.20073-89-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the newer RUNTIME_PM_OPS() macro instead of SET_RUNTIME_PM_OPS()
together with pm_ptr(), which allows us dropping ugly __maybe_unused
attributes.
This optimizes slightly when CONFIG_PM is disabled, too.
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250317095603.20073-58-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the newer RUNTIME_PM_OPS() macro instead of SET_RUNTIME_PM_OPS()
together with pm_ptr(), which allows us dropping ugly __maybe_unused
attributes.
This optimizes slightly when CONFIG_PM is disabled, too.
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250317095603.20073-57-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the newer RUNTIME_PM_OPS() macro instead of SET_RUNTIME_PM_OPS()
together with pm_ptr(), which allows us dropping ugly __maybe_unused
attributes.
This optimizes slightly when CONFIG_PM is disabled, too.
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250317095603.20073-56-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the newer SYSTEM_SLEEP_PM_OPS() macro instead of
SET_SYSTEM_SLEEP_PM_OPS() together with pm_ptr(), which allows us
superfluous CONFIG_PM_SLEEP ifdefs.
This optimizes slightly when CONFIG_PM is disabled, too.
Cc: patches@opensource.cirrus.com
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20250317095603.20073-55-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the newer RUNTIME_PM_OPS() and SYSTEM_SLEEP_PM_OPS() macros
instead of SET_RUNTIME_PM_OPS() and SET_SYSTEM_SLEEP_PM_OPS() together
with pm_ptr(), which allows us dropping superfluous CONFIG_PM ifdefs.
This optimizes slightly when CONFIG_PM is disabled, too.
Cc: patches@opensource.cirrus.com
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20250317095603.20073-54-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the newer EXPORT_GPL_DEV_PM_OPS() macro together with pm_ptr(),
which allows us to drop superfluous CONFIG_PM ifdefs.
This optimizes slightly when CONFIG_PM is disabled, too.
Cc: patches@opensource.cirrus.com
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20250317095603.20073-53-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the newer RUNTIME_PM_OPS() macro instead of SET_RUNTIME_PM_OPS()
together with pm_ptr(), which allows us dropping superfluous CONFIG_PM
ifdefs.
This optimizes slightly when CONFIG_PM is disabled, too.
Cc: patches@opensource.cirrus.com
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20250317095603.20073-52-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the newer RUNTIME_PM_OPS() macro instead of SET_RUNTIME_PM_OPS()
together with pm_ptr(), which allows us dropping ugly __maybe_unused
attributes and superfluous CONFIG_PM ifdefs.
This optimizes slightly when CONFIG_PM is disabled, too.
Cc: patches@opensource.cirrus.com
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20250317095603.20073-51-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the newer RUNTIME_PM_OPS() macro instead of SET_RUNTIME_PM_OPS()
together with pm_ptr(), which allows us dropping ugly __maybe_unused
attributes.
This optimizes slightly when CONFIG_PM is disabled, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250317095603.20073-50-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the newer RUNTIME_PM_OPS() macro instead of SET_RUNTIME_PM_OPS()
together with pm_ptr(), which allows us dropping ugly __maybe_unused
attributes.
This optimizes slightly when CONFIG_PM is disabled, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250317095603.20073-49-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the newer RUNTIME_PM_OPS() macro instead of SET_RUNTIME_PM_OPS()
together with pm_ptr(), which allows us dropping ugly __maybe_unused
attributes.
This optimizes slightly when CONFIG_PM is disabled, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250317095603.20073-48-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the newer SYSTEM_SLEEP_PM_OPS() macro instead of
SET_SYSTEM_SLEEP_PM_OPS() together with pm_ptr(), which allows us
dropping superfluous CONFIG_PM_SLEEP ifdefs.
This optimizes slightly when CONFIG_PM is disabled, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250317095603.20073-47-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the newer RUNTIME_PM_OPS() macro instead of SET_RUNTIME_PM_OPS()
together with pm_ptr(), which allows us dropping superfluous CONFIG_PM
ifdefs.
This optimizes slightly when CONFIG_PM is disabled, too.
Cc: Shenghao Ding <shenghao-ding@ti.com>
Cc: Kevin Lu <kevin-lu@ti.com>
Cc: Baojun Xu <baojun.xu@ti.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250317095603.20073-46-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the newer RUNTIME_PM_OPS() macro instead of SET_RUNTIME_PM_OPS(),
which allows us dropping ugly __maybe_unsed attributes.
Merely a cleanup, there should be no actual code change.
Cc: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250317095603.20073-45-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the newer RUNTIME_PM_OPS() macro instead of SET_RUNTIME_PM_OPS()
together with pm_ptr(), which allows us dropping ugly __maybe_unused
attributes.
This optimizes slightly when CONFIG_PM is disabled, too.
Cc: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250317095603.20073-44-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the newer RUNTIME_PM_OPS() and SYSTEM_SLEEP_PM_OPS() macros
instead of SET_RUNTIME_PM_OPS() and SET_SYSTEM_SLEEP_PM_OPS() together
with pm_ptr(), which allows us dropping ugly __maybe_unused
attributes.
This optimizes slightly when CONFIG_PM is disabled, too.
Cc: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250317095603.20073-43-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the newer RUNTIME_PM_OPS() and SYSTEM_SLEEP_PM_OPS() macros
instead of SET_RUNTIME_PM_OPS() and SET_SYSTEM_SLEEP_PM_OPS() together
with pm_ptr(), which allows us dropping ugly __maybe_unused
attributes.
This optimizes slightly when CONFIG_PM is disabled, too.
Cc: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250317095603.20073-42-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the newer RUNTIME_PM_OPS() and SYSTEM_SLEEP_PM_OPS() macros
instead of SET_RUNTIME_PM_OPS() and SET_SYSTEM_SLEEP_PM_OPS() together
with pm_ptr(), which allows us dropping ugly __maybe_unused
attributes.
This optimizes slightly when CONFIG_PM is disabled, too.
Cc: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250317095603.20073-41-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the newer RUNTIME_PM_OPS() and SYSTEM_SLEEP_PM_OPS() macros
instead of SET_RUNTIME_PM_OPS() and SET_SYSTEM_SLEEP_PM_OPS() together
with pm_ptr(), which allows us dropping ugly __maybe_unused
attributes.
This optimizes slightly when CONFIG_PM is disabled, too.
Cc: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250317095603.20073-40-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the newer RUNTIME_PM_OPS() and SYSTEM_SLEEP_PM_OPS() macros
instead of SET_RUNTIME_PM_OPS() and SET_SYSTEM_SLEEP_PM_OPS() together
with pm_ptr(), which allows us dropping ugly __maybe_unused
attributes.
This optimizes slightly when CONFIG_PM is disabled, too.
Cc: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250317095603.20073-39-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the newer RUNTIME_PM_OPS() and SYSTEM_SLEEP_PM_OPS() macros
instead of SET_RUNTIME_PM_OPS() and SET_SYSTEM_SLEEP_PM_OPS() together
with pm_ptr(), which allows us dropping ugly __maybe_unused
attributes.
This optimizes slightly when CONFIG_PM is disabled, too.
Cc: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250317095603.20073-38-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the newer RUNTIME_PM_OPS() and SYSTEM_SLEEP_PM_OPS() macros
instead of SET_RUNTIME_PM_OPS() and SET_SYSTEM_SLEEP_PM_OPS() together
with pm_ptr(), which allows us dropping ugly __maybe_unused
attributes.
This optimizes slightly when CONFIG_PM is disabled, too.
Cc: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250317095603.20073-37-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the newer SYSTEM_SLEEP_PM_OPS() macro instead of
SET_SYSTEM_SLEEP_PM_OPS() together with pm_ptr(), which allows us
dropping ugly __maybe_unused attributes.
This optimizes slightly when CONFIG_PM is disabled, too.
Cc: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250317095603.20073-36-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the newer SYSTEM_SLEEP_PM_OPS() macro instead of
SET_SYSTEM_SLEEP_PM_OPS() together with pm_ptr(), which allows us
dropping ugly __maybe_unused attributes.
This optimizes slightly when CONFIG_PM is disabled, too.
Cc: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250317095603.20073-35-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the newer RUNTIME_PM_OPS() and SYSTEM_SLEEP_PM_OPS() macros
instead of SET_RUNTIME_PM_OPS() and SET_SYSTEM_SLEEP_PM_OPS() together
with pm_ptr(), which allows us dropping ugly __maybe_unused
attributes.
This optimizes slightly when CONFIG_PM is disabled, too.
Cc: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250317095603.20073-34-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the newer RUNTIME_PM_OPS() and SYSTEM_SLEEP_PM_OPS() macros
instead of SET_RUNTIME_PM_OPS() and SET_SYSTEM_SLEEP_PM_OPS() together
with pm_ptr(), which allows us dropping ugly __maybe_unused
attributes.
This optimizes slightly when CONFIG_PM is disabled, too.
Cc: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250317095603.20073-33-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the newer RUNTIME_PM_OPS() and SYSTEM_SLEEP_PM_OPS() macros
instead of SET_RUNTIME_PM_OPS() and SET_SYSTEM_SLEEP_PM_OPS() together
with pm_ptr(), which allows us dropping ugly __maybe_unused
attributes.
This optimizes slightly when CONFIG_PM is disabled, too.
Cc: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250317095603.20073-32-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the newer RUNTIME_PM_OPS() and SYSTEM_SLEEP_PM_OPS() macros
instead of SET_RUNTIME_PM_OPS() and SET_SYSTEM_SLEEP_PM_OPS() together
with pm_ptr(), which allows us dropping ugly __maybe_unused
attributes.
This optimizes slightly when CONFIG_PM is disabled, too.
Cc: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250317095603.20073-31-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the newer RUNTIME_PM_OPS() and SYSTEM_SLEEP_PM_OPS() macros
instead of SET_RUNTIME_PM_OPS() and SET_SYSTEM_SLEEP_PM_OPS() together
with pm_ptr(), which allows us dropping ugly __maybe_unused
attributes.
This optimizes slightly when CONFIG_PM is disabled, too.
Cc: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250317095603.20073-30-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the newer EXPORT_GPL_DEV_PM_OPS() macro together with pm_ptr(),
which allows us to drop superfluous CONFIG_PM ifdefs.
This optimizes slightly when CONFIG_PM is disabled, too.
Cc: Shenghao Ding <shenghao-ding@ti.com>
Cc: Kevin Lu <kevin-lu@ti.com>
Cc: Baojun Xu <baojun.xu@ti.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250317095603.20073-29-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the newer RUNTIME_PM_OPS() macro instead of SET_RUNTIME_PM_OPS()
together with pm_ptr(), which allows us dropping ugly __maybe_unused
attributes.
This optimizes slightly when CONFIG_PM is disabled, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250317095603.20073-28-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the newer SYSTEM_SLEEP_PM_OPS() macro instead of
SET_SYSTEM_SLEEP_PM_OPS() together with pm_ptr(), which allows us
dropping superfluous CONFIG_PM_SLEEP ifdefs.
This optimizes slightly when CONFIG_PM is disabled, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250317095603.20073-27-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the newer RUNTIME_PM_OPS() macro instead of SET_RUNTIME_PM_OPS()
together with pm_ptr(), which allows us dropping superfluous CONFIG_PM
ifdefs.
This optimizes slightly when CONFIG_PM is disabled, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250317095603.20073-26-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the newer SYSTEM_SLEEP_PM_OPS() macro instead of
SET_SYSTEM_SLEEP_PM_OPS() together with pm_ptr(), which allows us
dropping ugly __maybe_unsed attributes.
This optimizes slightly when CONFIG_PM is disabled, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250317095603.20073-25-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the newer SYSTEM_SLEEP_PM_OPS() macro instead of
SET_SYSTEM_SLEEP_PM_OPS() together with pm_ptr(), which allows us
dropping superfluous CONFIG_PM_SLEEP ifdefs.
This optimizes slightly when CONFIG_PM is disabled, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250317095603.20073-24-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the newer SYSTEM_SLEEP_PM_OPS() macro instead of
SET_SYSTEM_SLEEP_PM_OPS() together with pm_ptr(), which allows us
dropping superfluous CONFIG_PM_SLEEP ifdefs.
This optimizes slightly when CONFIG_PM is disabled, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250317095603.20073-23-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the newer RUNTIME_PM_OPS() and SYSTEM_SLEEP_PM_OPS() macros
instead of SET_RUNTIME_PM_OPS() and SET_SYSTEM_SLEEP_PM_OPS() together
with pm_ptr(), which allows us dropping superfluous CONFIG_PM and
CONFIG_PM_SLEEP ifdefs.
This optimizes slightly when CONFIG_PM is disabled, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250317095603.20073-22-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the newer RUNTIME_PM_OPS() and SYSTEM_SLEEP_PM_OPS() macros
instead of SET_RUNTIME_PM_OPS() and SET_SYSTEM_SLEEP_PM_OPS() together
with pm_ptr(), which allows us dropping superfluous CONFIG_PM and
CONFIG_PM_SLEEP ifdefs.
This optimizes slightly when CONFIG_PM is disabled, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250317095603.20073-21-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the newer RUNTIME_PM_OPS() macro instead of SET_RUNTIME_PM_OPS()
together with pm_ptr(), which allows us dropping ugly __maybe_unused
attributes.
This optimizes slightly when CONFIG_PM is disabled, too.
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250317095603.20073-20-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the newer RUNTIME_PM_OPS() and SYSTEM_SLEEP_PM_OPS() macros
instead of SET_RUNTIME_PM_OPS() and SET_SYSTEM_SLEEP_PM_OPS() together
with pm_ptr(), which allows us dropping superfluous CONFIG_PM ifdefs.
This optimizes slightly when CONFIG_PM is disabled, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250317095603.20073-19-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the newer RUNTIME_PM_OPS() and SYSTEM_SLEEP_PM_OPS() macros
instead of SET_RUNTIME_PM_OPS() and SET_SYSTEM_SLEEP_PM_OPS() together
with pm_ptr(), which allows us dropping ugly __maybe_unused
attributes.
This optimizes slightly when CONFIG_PM is disabled, too.
Cc: support.opensource@diasemi.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250317095603.20073-18-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the newer RUNTIME_PM_OPS() and SYSTEM_SLEEP_PM_OPS() macros
instead of SET_RUNTIME_PM_OPS() and SET_SYSTEM_SLEEP_PM_OPS() together
with pm_ptr(), which allows us dropping ugly __maybe_unused
attributes.
This optimizes slightly when CONFIG_PM is disabled, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250317095603.20073-17-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the newer RUNTIME_PM_OPS() macro instead of SET_RUNTIME_PM_OPS()
together with pm_ptr(), which allows us dropping superfluous CONFIG_PM
ifdefs.
This optimizes slightly when CONFIG_PM is disabled, too.
Cc: patches@opensource.cirrus.com
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20250317095603.20073-16-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the newer RUNTIME_PM_OPS() macro instead of SET_RUNTIME_PM_OPS()
together with pm_ptr(), which allows us dropping superfluous CONFIG_PM
ifdefs.
This optimizes slightly when CONFIG_PM is disabled, too.
Cc: patches@opensource.cirrus.com
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20250317095603.20073-15-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the newer RUNTIME_PM_OPS() macro instead of SET_RUNTIME_PM_OPS()
together with pm_ptr(), which allows us dropping ugly __maybe_unused
attributes.
This optimizes slightly when CONFIG_PM is disabled, too.
Cc: patches@opensource.cirrus.com
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20250317095603.20073-14-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the newer EXPORT_GPL_DEV_PM_OPS() macro together with pm_ptr(),
which allows us to drop superfluous CONFIG_PM ifdefs.
This optimizes slightly when CONFIG_PM is disabled, too.
Cc: patches@opensource.cirrus.com
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20250317095603.20073-13-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the newer SYSTEM_SLEEP_PM_OPS() macro instead of
SET_SYSTEM_SLEEP_PM_OPS() together with pm_ptr(), which allows us
dropping ugly __maybe_unused attributes.
This optimizes slightly when CONFIG_PM is disabled, too.
Cc: patches@opensource.cirrus.com
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20250317095603.20073-12-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the newer SYSTEM_SLEEP_PM_OPS() macro instead of
SET_SYSTEM_SLEEP_PM_OPS().
Also, drop superfluous __maybe_unused attributes to cs42l51_suspend()
and _resume() functions.
Merely a cleanup, there should be no actual code change.
Cc: patches@opensource.cirrus.com
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20250317095603.20073-11-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the newer RUNTIME_PM_OPS() and SYSTEM_SLEEP_PM_OPS() macros
instead of SET_RUNTIME_PM_OPS() and SET_SYSTEM_SLEEP_PM_OPS() together
with pm_ptr(), which allows us dropping ugly __maybe_unused
attributes.
This optimizes slightly when CONFIG_PM is disabled, too.
Cc: patches@opensource.cirrus.com
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20250317095603.20073-10-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the newer RUNTIME_PM_OPS() macro instead of SET_RUNTIME_PM_OPS()
together with pm_ptr(), which allows us dropping ugly __maybe_unused
attributes.
This optimizes slightly when CONFIG_PM is disabled, too.
Cc: patches@opensource.cirrus.com
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20250317095603.20073-9-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the newer RUNTIME_PM_OPS() macro instead of SET_RUNTIME_PM_OPS()
together with pm_ptr(), which allows us dropping ugly __maybe_unused
attributes.
This optimizes slightly when CONFIG_PM is disabled, too.
Cc: patches@opensource.cirrus.com
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20250317095603.20073-8-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the newer RUNTIME_PM_OPS() macro instead of SET_RUNTIME_PM_OPS()
together with pm_ptr(), which allows us dropping ugly __maybe_unused
attributes.
This optimizes slightly when CONFIG_PM is disabled, too.
Cc: patches@opensource.cirrus.com
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20250317095603.20073-7-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the newer RUNTIME_PM_OPS() macro instead of SET_RUNTIME_PM_OPS()
together with pm_ptr(), which allows us dropping superfluous CONFIG_PM
ifdefs.
This optimizes slightly when CONFIG_PM is disabled, too.
Cc: patches@opensource.cirrus.com
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20250317095603.20073-6-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the newer RUNTIME_PM_OPS() and SYSTEM_SLEEP_PM_OPS() macros
instead of SET_RUNTIME_PM_OPS() and SET_SYSTEM_SLEEP_PM_OPS() together
with pm_ptr(), which allows us dropping ugly __maybe_unused
attributes.
This optimizes slightly when CONFIG_PM is disabled, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250317095603.20073-5-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the newer RUNTIME_PM_OPS() and SYSTEM_SLEEP_PM_OPS() macros
instead of SET_RUNTIME_PM_OPS() and SET_SYSTEM_SLEEP_PM_OPS() together
with pm_ptr(), which allows us dropping ugly __maybe_unused attributes
and CONFIG_PM ifdefs.
This optimizes slightly when CONFIG_PM is disabled, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250317095603.20073-4-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the newer RUNTIME_PM_OPS() and SYSTEM_SLEEP_PM_OPS() macros
instead of SET_RUNTIME_PM_OPS () and SET_SYSTEM_SLEEP_PM_OPS()
together with pm_ptr(), which allows us dropping ugly __maybe_unused
attributes.
This optimizes slightly when CONFIG_PM is disabled, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250317095603.20073-3-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
'destroy_workqueue()' already drains the queue before destroying it, so
there is no need to flush it explicitly.
Remove the redundant 'flush_workqueue()' calls.
This was generated with coccinelle:
@@
expression E;
@@
-flush_workqueue(E);
destroy_workqueue(E);
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Link: https://patch.msgid.link/20250312072635.1429870-1-nichen@iscas.ac.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
When snd_soc_dapm_new_controls() or snd_soc_dapm_add_routes() fails,
wcd937x_soc_codec_probe() returns without releasing 'wcd937x->clsh_info',
which is allocated by wcd_clsh_ctrl_alloc. Add wcd_clsh_ctrl_free()
to prevent potential memory leak.
Fixes: 313e978df7 ("ASoC: codecs: wcd937x: add audio routing and Kconfig")
Cc: stable@vger.kernel.org
Signed-off-by: Haoxiang Li <haoxiang_li2024@163.com>
Link: https://patch.msgid.link/20250226085050.3584898-1-haoxiang_li2024@163.com
Signed-off-by: Mark Brown <broonie@kernel.org>
clk_disable_unprepare() already checks NULL by using IS_ERR_OR_NULL.
Remove unneeded NULL check for adc3xxx->mclk here.
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Link: https://patch.msgid.link/20250312034337.1235378-1-nichen@iscas.ac.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
All varibale allocated by kzalloc and devm_kzalloc could be NULL.
Multiple pointer checks and their cleanup are added.
This issue is found by our static analysis tool
Signed-off-by: Chenyuan Yang <chenyuan0y@gmail.com>
Link: https://patch.msgid.link/20250311015714.1333857-1-chenyuan0y@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The current code for the IRQ in pcm6240 makes no sense:
it looks up an IRQ with of_irq_get(), treat it as a GPIO
by issuing gpio_request(), gpio_direction_input()
and gpio_to_irq() on it.
This is just wrong, if the device tree assigns the IRQ
from a GPIO number this is just incorrect: it is clearly
stated that GPIO providers and IRQ providers are
orthogonal.
It is possible to look up an IRQ to a corresponding GPIO
line but this is taking an IRQ and pretending it's a
GPIO, which is just semantically wrong.
Drop the offending code and treat the IRQ that we get
from the device tree as any other IRQ, see for example
other codec drivers.
The DT bindings for this codec does not have any in-tree
DTS files, which may explain why things are weird.
As a bonus, this moves the driver away from the legacy
<linux/gpio.h> include.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patch.msgid.link/20250312-pcm-codecs-v1-3-41ffc4f8fc5c@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This converts the PCM3008 driver to look up the GPIO lines
using descriptors.
Apparently there are no in-tree users of the platform data
struct, so users need to adopt.
New users can associate the GPIO lines with the platform
device "pcm3008-codec".
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patch.msgid.link/20250312-pcm-codecs-v1-2-41ffc4f8fc5c@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver includes the legacy GPIO header <linux/gpio.h>
but does not use any symbols from it so drop the include.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patch.msgid.link/20250312-pcm-codecs-v1-1-41ffc4f8fc5c@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a stub for mt6359_accdet_enable_jack_detect() to prevent linker
failures in the machine sound drivers calling it when
CONFIG_SND_SOC_MT6359_ACCDET is not enabled.
Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://patch.msgid.link/20250306-mt8188-accdet-v3-3-7828e835ff4b@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver is for amplifiers aw88166 of Awinic Technology
Corporation. The AW88166 is a high efficiency digital
Smart K audio amplifier
Signed-off-by: Weidong Wang <wangweidong.a@awinic.com>
Link: https://patch.msgid.link/20250312120100.9730-3-wangweidong.a@awinic.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The former code sets the V slot from inside set_bitwidth according to
the bitwidth of the PCM format. That's wrong, since:
* It overrides the V slot parsed from DT binding.
* The V slot is set shifted behind the I slot by the length of the PCM
bitwidth, but the PCM bitwidth has no assured relation to the TDM
slot width.
Replace the former logic by setting up the I/V sense transmission only
in case of both I/V slots being specified in devicetree, and never
override those values. In case the slots are left unspecified, disable
the transmission completely.
There's an improbable case someone is relying on the old behavior, but
if so, that's a setup that only works by accident, and cannot be sanely
supported going forward. There's no indication anyone is consuming the
I/V sense data up to today, so break the former behavior.
Reviewed-by: Neal Gompa <neal@gompa.dev>
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Signed-off-by: James Calligeros <jcalligeros99@gmail.com>
Link: https://patch.msgid.link/20250227-apple-codec-changes-v3-6-cbb130030acf@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a new explicit function for the setting of I/V sense TDM slots.
Reviewed-by: Neal Gompa <neal@gompa.dev>
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Signed-off-by: James Calligeros <jcalligeros99@gmail.com>
Link: https://patch.msgid.link/20250227-apple-codec-changes-v3-5-cbb130030acf@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add control to expose the option of autoretry behavior on overcurrent
events in the codec.
Reviewed-by: Neal Gompa <neal@gompa.dev>
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Signed-off-by: James Calligeros <jcalligeros99@gmail.com>
Link: https://patch.msgid.link/20250227-apple-codec-changes-v3-4-cbb130030acf@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
SN012776 is a speaker amp chip found in Apple's 2021 laptops. It appears
similar and more-or-less compatible to TAS2764. Extend the TAS2764
driver with some SN012776 specifics and configure the chip assuming
it's in one of the Apple machines.
Reviewed-by: Neal Gompa <neal@gompa.dev>
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Signed-off-by: James Calligeros <jcalligeros99@gmail.com>
Link: https://patch.msgid.link/20250227-apple-codec-changes-v3-3-cbb130030acf@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The custom suspend function causes a build warning when CONFIG_PM_SLEEP
is disabled:
sound/soc/codecs/cs42l43.c:2405:12: error: unused function 'cs42l43_codec_runtime_force_suspend' [-Werror,-Wunused-function]
Change SET_SYSTEM_SLEEP_PM_OPS() to the newer SYSTEM_SLEEP_PM_OPS(),
to avoid this.
Fixes: 164b7dd454 ("ASoC: cs42l43: Add jack delay debounce after suspend")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Maciej Strozek <mstrozek@opensource.cirrus.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250305172738.3437513-1-arnd@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmfOKBUeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG1aQH/iC+Oyij4VxAjBek
BOXIT/p6CwlIXb8ObiWWcRjDPizlcxb3RaV8J2RO+IqaQ2wltxpFANq2G7Re2FPm
SNcEpIURAOVcxHGedcfFA91srO5F4FzNTO8LVp7MIbcgMYy3pdk+dbZmi6A691R+
t9pb74m+MAnF1o/MUx7pUlhAT/4ymuuR0F7WCSg4h0Xwe5m0nlJY89kJBC7PCjyd
n3mdhsz3rDSLmt/z/T7HGD89r8sYSvm9cOKtL3ELgGTrm7boQV8ii9Y9w04DI8PQ
JmIernugcCxmhH36mVUAHgJf2+/T388xFUh/D5+skeUOUZpaJZG866rnb32WpsHc
eWLFUeg=
=Wypt
-----END PGP SIGNATURE-----
Backmerge tag 'v6.14-rc6' into drm-next
This is a backmerge from Linux 6.14-rc6, needed for the nova PR.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Free some resources in the error handling path of the probe, as already
done in the remove function.
Fixes: e3523e0186 ("ASoC: wm0010: Add initial wm0010 DSP driver")
Fixes: fd8b965744 ("ASoC: wm0010: Clear IRQ as wake source and include missing header")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/5139ba1ab8c4c157ce04e56096a0f54a1683195c.1741549792.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the return value from spi_setup() is not checked for a failure.
It is unlikely it will ever fail in this particular case but it is still
better to add this check for the sake of completeness and correctness. This
is cheap since it is performed once when the device is being probed.
Handle spi_setup() return value.
Found by Linux Verification Center (linuxtesting.org) with Svace.
Fixes: 872fc0b6bd ("ASoC: cs35l41: Set the max SPI speed for the whole device")
Signed-off-by: Vitaliy Shevtsov <v.shevtsov@mt-integration.ru>
Link: https://patch.msgid.link/20250304115643.2748-1-v.shevtsov@mt-integration.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT722_SDCA_ENT_FU15,
RT722_SDCA_CTL_FU_CH_GAIN, CH_01) ... SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY,
RT722_SDCA_ENT_FU15, RT722_SDCA_CTL_FU_CH_GAIN, CH_04) are used by the
"FU15 Boost Volume" control, but not marked as readable.
And the mbq size are 2 for those registers.
Fixes: 7f5d6036ca ("ASoC: rt722-sdca: Add RT722 SDCA driver")
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Shuming Fan <shumingf@realtek.com>
Link: https://patch.msgid.link/20250310080440.58797-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The custom suspend function causes a build warning when CONFIG_PM_SLEEP
is disabled:
sound/soc/codecs/cs42l43.c:2405:12: error: unused function 'cs42l43_codec_runtime_force_suspend' [-Werror,-Wunused-function]
Change SET_SYSTEM_SLEEP_PM_OPS() to the newer SYSTEM_SLEEP_PM_OPS(),
to avoid this.
Fixes: 164b7dd454 ("ASoC: cs42l43: Add jack delay debounce after suspend")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250305172738.3437513-1-arnd@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The changes to DECLARE_ADAU17X1_DSP_MUX_CTRL did avoid the issue with a
compiler not liking all the macro indirection. However it introduced a
new issue with respect to the mux not being declared static:
sound/soc/codecs/adau17x1.c:275:8: sparse: sparse: symbol
'adau17x1_dac_mux' was not declared. Should it be static?
sound/soc/codecs/adau17x1.c:278:8: sparse: sparse: symbol
'adau17x1_capture_mux' was not declared. Should it be static?
Fix this up by going back to the inline declaration of the soc_enum, but
just call SOC_ENUM_EXT directly rather than indirecting through
SOC_DAPM_ENUM_EXT.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202503061119.4QGlnOi6-lkp@intel.com/
Fixes: c951b20766 ("ASoC: dapm: Use ASoC control macros where possible")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250306104233.1638625-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
"generic_new_peripheral_assigned: invalid dev_num 1, wake supported 1"
is reported by our internal CI test.
Rt1320's wake feature is not used in Linux and that's why it is not in
the wake_capable_list[] list in intel_auxdevice.c.
However, BIOS may set it as wake-capable. Overwrite wake_capable to 0
in the codec driver to align with wake_capable_list[].
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Acked-by: Shuming Fan <shumingf@realtek.com>
Link: https://patch.msgid.link/20250305134113.201326-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Charles Keepax <ckeepax@opensource.cirrus.com>:
Tidy up the ASoC control value macros. Fix some drivers that should be
using core macros that aren't, combine the existing core macros to be
a little more consistent in style, and update the core macros to use
each other where possible.
Merge series from Cezary Rojewski <cezary.rojewski@intel.com>:
The series aims to streamline the formatting for ACPI IDs so that a
single pattern can be used to identify the device.
Work implicitly suggested by Andy Shevchenko - reading and learning from
number of his reviews on the Linux mailing lists.
Several formats do exists, however, after technical discussion PCI-based
format has been selected as the recommended one. For Realtek devices, it
is going to be 10ECxxxx where 10EC unambiguously identifies Realtek
company whereas the following 4 hexes specify the PART_ID i.e.: the
device.
While at it, there shall be no comma after the terminator entry and
initializing fields with 0 for statically defined structs is redundant.
Merge series from Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>:
We have both
(A) SND_SOC_DAIFMT_CB{M/S}_CF{M/S} : Master/Slave.
(B) SND_SOC_DAIFMT_CB{P/C}_CF{P/S} : Provider/Consumer
We should use (B), and want to remove (A). This patch-set do it.
Hardware reports jack absent after reset/suspension regardless of jack
state, so introduce an additional delay only in suspension case to allow
proper detection to take place after a short delay.
Signed-off-by: Maciej Strozek <mstrozek@opensource.cirrus.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250304140504.139245-1-mstrozek@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A recent dtbs_check error fix in mt6359.dtsi file changed a node name
(from "mt6359codec" to "audio-codec") without modifying the mt6539
codec code that uses it.
It leads to a probe failure after devicetree parsing returns in error:
```
[ 1.354025] mt6359-sound mt6359-sound: mt6359_platform_driver_probe() failed to parse dts
[ 1.355066] mt6359-sound mt6359-sound: probe with driver mt6359-sound failed with error -22
```
So, add the child node retrieval with the new name and if not found,
try with the older one for backward compatibility.
Fixes: 76b35f59bb ("arm64: dts: mediatek: mt6359: fix dtbs_check error for audio-codec")
Signed-off-by: Louis-Alexis Eyraud <louisalexis.eyraud@collabora.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://patch.msgid.link/20250228-mt6359-fix-probe-failed-v1-1-64941d387b2c@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Update the DAPM kcontrol creation macros to use the ASoC macros where a
helpful version exists. One minor fixup is required in adau17x1, the
compiler doesn't like the extra level of macro indirection coupled with
the inline struct definition. Make the struct definition explicit.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250303171424.444556-12-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The rt715 does not appear to use the SOC_DOUBLE_R_EXT() macro and even
if it did, the macro is defined identically in the ASoC headers.
Remove the redundant macro definitions.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250303171424.444556-3-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Temperatures are reported in units of Celsius however hwmon expects
values to be in millidegree of Celsius. Userspace tools observe values
close to zero and report it as "Not available" or incorrect values like
0C or 1C. Add a simple conversion to fix that.
Before the change:
wsa884x-virtual-0
Adapter: Virtual device
temp1: +0.0°C
--
wsa884x-virtual-0
Adapter: Virtual device
temp1: +0.0°C
Also reported as N/A before first amplifier power on.
After this change and initial wsa884x power on:
wsa884x-virtual-0
Adapter: Virtual device
temp1: +39.0°C
--
wsa884x-virtual-0
Adapter: Virtual device
temp1: +37.0°C
Tested on sm8550 only.
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Alexey Klimov <alexey.klimov@linaro.org>
Link: https://patch.msgid.link/20250221044024.1207921-1-alexey.klimov@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Read temperature of the amplifier and expose it via hwmon interface, which
will be later used during calibration of speaker protection algorithms.
The method is the same as for wsa884x and therefore this is based on
Krzysztof Kozlowski's approach implemented in commit 6b99dc62d9 ("ASoC:
codecs: wsa884x: Implement temperature reading and hwmon").
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Steev Klimaszewski <steev@kali.org>
Signed-off-by: Alexey Klimov <alexey.klimov@linaro.org>
Tested-by: Steev Klimaszewski <steev@kali.org> #Thinkpad X13s
Link: https://patch.msgid.link/20250221032141.1206902-1-alexey.klimov@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Follow PCI-based format (10ECxxxx) for ACPI IDs by adding relevant
entries to the existing table.
While at it, there shall be no comma after the terminator entry and
initializing fields with 0 for statically defined structs is redundant.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20250226112612.166989-23-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Follow PCI-based format (10ECxxxx) for ACPI IDs by adding relevant
entries to the existing table.
While at it, there shall be no comma after the terminator entry and
initializing fields with 0 for statically defined structs is redundant.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20250226112612.166989-22-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Follow PCI-based format (10ECxxxx) for ACPI IDs by adding relevant
entries to the existing table.
While at it, there shall be no comma after the terminator entry and
initializing fields with 0 for statically defined structs is redundant.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20250226112612.166989-21-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There shall be no comma after the terminator entry and initializing
fields with 0 for statically defined structs is redundant.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20250226112612.166989-20-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There shall be no comma after the terminator entry and initializing
fields with 0 for statically defined structs is redundant.
While at it, sort the IDs alphabetically.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20250226112612.166989-19-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There shall be no comma after the terminator entry and initializing
fields with 0 for statically defined structs is redundant.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20250226112612.166989-18-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There shall be no comma after the terminator entry and initializing
fields with 0 for statically defined structs is redundant.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20250226112612.166989-17-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There shall be no comma after the terminator entry and initializing
fields with 0 for statically defined structs is redundant.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20250226112612.166989-16-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There shall be no comma after the terminator entry and initializing
fields with 0 for statically defined structs is redundant.
While at it, sort the IDs alphabetically.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20250226112612.166989-15-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
