Add CMU_PERIS block compatible, and clock definitions.
CMU_PERIS requires one bus clock dependency, and it's used for i.e the MCT.
Signed-off-by: Igor Belwon <igor.belwon@mentallysanemainliners.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250104-exynos990-cmu-v1-1-9f54d69286d6@mentallysanemainliners.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
The QCS8300 camera clock controller is a derivative of SA8775P, but has
an additional clock and minor differences. Hence, reuse the SA8775P
camera bindings and add additional clock required for QCS8300.
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Imran Shaik <quic_imrashai@quicinc.com>
Link: https://lore.kernel.org/r/20250109-qcs8300-mm-patches-new-v4-3-63e8ac268b02@quicinc.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
The QCS8300 GPU clock controller is a derivative of SA8775P, but has few
additional clocks and minor differences. Hence, reuse gpucc bindings of
SA8775P and add additional clocks required for QCS8300.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Imran Shaik <quic_imrashai@quicinc.com>
Link: https://lore.kernel.org/r/20250109-qcs8300-mm-patches-new-v4-1-63e8ac268b02@quicinc.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
The patch converts st,stm32-rcc.txt to the JSON schema, but it does more
than that. The old bindings, in fact, only covered the stm32f{4,7}
platforms and not the stm32h7. Therefore, to avoid patch submission tests
failing, it was necessary to add the corresponding compatible (i. e.
st,stm32h743-rcc) and specify that, in this case, 3 are the clocks instead
of the 2 required for the stm32f{4,7} platforms.
Additionally, the old bindings made no mention of the st,syscfg property,
which is used by both the stm32f{4,7} and the stm32h7 platforms.
The patch also fixes the files referencing to the old st,stm32-rcc.txt.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250114182021.670435-2-dario.binacchi@amarulasolutions.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add ID for eMMC for EN7581. This is to control clock selection of eMMC
between 200MHz and 150MHz.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20250113231030.6735-4-ansuelsmth@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Drop NUM_CLOCKS define for EN7581 include. This is not a binding and
should not be placed here. Value is derived internally in the user
driver.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250113231030.6735-3-ansuelsmth@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
SM6115 (and its derivatives or similar SoCs) has an LPASS clock
controller block which provides audio-related resets.
Add bindings for it.
Cc: Konrad Dybcio <konradybcio@kernel.org>
Cc: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
[alexey.klimov slightly changed the commit message]
Signed-off-by: Alexey Klimov <alexey.klimov@linaro.org>
Link: https://lore.kernel.org/r/20241212002551.2902954-2-alexey.klimov@linaro.org
[bjorn: Adjusted Konrad's address]
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The GCC_XO_CLK is required for the functionality of the WiFi
copy engine block. Therefore, add the GCC_XO_CLK macro.
Signed-off-by: Manikanta Mylavarapu <quic_mmanikan@quicinc.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20241210064110.130466-2-quic_mmanikan@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The gcc_apss_dbg clk is access protected by trust zone, and accessing
it results in a kernel crash. Therefore remove the gcc_apss_dbg_clk macro.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Manikanta Mylavarapu <quic_mmanikan@quicinc.com>
Link: https://lore.kernel.org/r/20241217113909.3522305-3-quic_mmanikan@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The CMN PLL controller provides clocks to networking hardware blocks
and to GCC on Qualcomm IPQ9574 SoC. It receives input clock from the
on-chip Wi-Fi, and produces output clocks at fixed rates. These output
rates are predetermined, and are unrelated to the input clock rate.
The primary purpose of CMN PLL is to supply clocks to the networking
hardware such as PPE (packet process engine), PCS and the externally
connected switch or PHY device. The CMN PLL block also outputs fixed
rate clocks to GCC, such as 24 MHZ as XO clock and 32 KHZ as sleep
clock supplied to GCC.
Signed-off-by: Luo Jie <quic_luoj@quicinc.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250103-qcom_ipq_cmnpll-v8-1-c89fb4d4849d@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add bindings for the Qualcomm SM8750 Display Clock Controller (DISPCC).
Bindings are similar to existing SM8550 and SM8650 (same clock inputs),
but the clock hierarchy is quite different and these are not compatible
devices.
The binding header was copied from downstream sources, so I retained
original copyrights.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250106-sm8750-dispcc-v2-1-6f42beda6317@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add device tree bindings for the global clock controller on Qualcomm
SM8750 platform.
Signed-off-by: Taniya Das <quic_tdas@quicinc.com>
Signed-off-by: Melody Olvera <quic_molvera@quicinc.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20241204-sm8750_master_clks-v3-5-1a8f31a53a86@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Export PLL_VIDEO_2X and PLL_MIPI, these will be used to explicitly
select TCON0 clock parent in dts
Fixes: ca1170b699 ("clk: sunxi-ng: a64: force select PLL_MIPI in TCON0 mux")
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Frank Oltmanns <frank@oltmanns.dev> # on PinePhone
Tested-by: Stuart Gathman <stuart@gathman.org> # on OG Pinebook
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://patch.msgid.link/20250104074035.1611136-2-anarsoul@gmail.com
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Add SPDIF IPG clk. The SPDIF IPG clock and root clock
share same clock gate.
Fixes: 1c4a4f7362 ("arm64: dts: imx93: Add audio device nodes")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20241119015805.3840606-2-shengjiu.wang@nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
To make it easier for X1P4 and X1E to share a common device tree base,
extend the existing latter's GPUCC bindings and reuse them on the
former platform.
While not in the same file, it only makes sense to introduce the new
compatible in this commit as well.
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20241221-topic-x1p4_clk-v1-2-dbaeccb74884@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add the `microchip,sama7d65-pmc` compatible string to the existing binding,
since the SAMA7D65 PMC shares the same properties and clock requirements
as the SAMA7G5.
Export MCK3 and MCK5 to be accessed and referenced in DT to assign to
the clocks property for sama7d65 SoC.
Signed-off-by: Dharma Balasubiramani <dharma.b@microchip.com>
Signed-off-by: Ryan Wanner <Ryan.Wanner@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/5252a28531deaee67af1edd8e72d45ca57783464.1733505542.git.Ryan.Wanner@microchip.com
[claudiu.beznea: use tabs instead of spaces in
include/dt-bindings/clock/at91.h]
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Add dt-schema documentation for the Exynos990 SoC CMU.
This clock management unit has a topmost block (CMU_TOP)
that generates top clocks for other blocks. Currently the
only other block implemented is CMU_HSI0, which provides
clocks for the USB part of the SoC.
Also, device-tree binding definitions added for these blocks:
- CMU_TOP
- CMU_HSI0
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Igor Belwon <igor.belwon@mentallysanemainliners.org>
Link: https://lore.kernel.org/r/20241209-exynos990-cmu-v4-1-57f07080f9e4@mentallysanemainliners.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Document the device tree bindings for the Renesas RZ/G3E SoC
Clock Pulse Generator (CPG).
Also define constants for the core clocks of the RZ/G3E SoC.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20241203105005.103927-5-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add clock IDs for the slow clock controller. Previously, raw numbers
were used (0 or 1) for clocks generated by the slow clock controller. This
leads to confusion and wrong IDs were used on few device trees. To avoid
this add macros.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240826173116.3628337-2-claudiu.beznea@tuxon.dev
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
some unit tests for the assigned clk rates feature in DeviceTree. On the vendor
driver side, we gained a whole pile of SoC driver support detailed below. The
majority in the diffstat is Qualcomm, but there's also quite a few Samsung and
Mediatek clk driver additions in here as well. The top vendors is quite common,
but the sheer amount of new drivers is uncommon, so I'm anticipating a larger
number of fixes for clk drivers this cycle.
Core:
- devm_clk_bulk_get_all_enabled() to return number of clks acquired
- devm_clk_hw_register_gate_parent_hw() helper to modernize drivers
- KUnit tests for clk-assigned-rates{,-u64}
New Drivers:
- Marvell PXA1908 SoC clks
- Mobileye EyeQ5, EyeQ6L and EyeQ6H clk driver
- TWL6030 clk driver
- Nuvoton Arbel BMC NPCM8XX SoC clks
- MediaTek MT6735 SoC clks
- MediaTek MT7620, MT7628 and MT7688 MMC clks
- Add a driver for gated fixed rate clocks
- Global clock controllers for Qualcomm QCS8300 and IPQ5424 SoCs
- Camera, display and video clock controllers for Qualcomm SA8775P SoCs
- Global, display, GPU, TCSR, and RPMh clock controllers for Qualcomm SAR2130P
- Global, camera, display, GPU, and video clock controllers for Qualcomm
SM8475 SoCs
- RTC power domain and Battery Backup Function (VBATTB) clock support for the
Renesas RZ/G3S SoC
- Qualcomm IPQ9574 alpha PLLs
- Support for i.MX91 CCM in the i.MX93 driver
- Microchip LAN969X SoC clks
- Cortex-A55 core clocks and Interrupt Control Unit (ICU) clock and reset on
Renesas RZ/V2H(P)
- Samsung ExynosAutov920 clk drivers for PERIC1, MISC, HSI0 and HSI1
- Samsung Exynos8895 clk drivers for FSYS0/1, PERIC0/1, PERIS and TOP
Updates:
- Convert more clk bindings to YAML
- Various clk driver cleanups: NULL checks, add const, etc.
- Remove END/NUM #defines that count number of clks in various binding headers
- Continue moving reset drivers to drivers/reset via auxiliary bus
-----BEGIN PGP SIGNATURE-----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=FqLm
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"The core framework gained a clk provider helper, a clk consumer
helper, and some unit tests for the assigned clk rates feature in
DeviceTree. On the vendor driver side, we gained a whole pile of SoC
driver support detailed below. The majority in the diffstat is
Qualcomm, but there's also quite a few Samsung and Mediatek clk driver
additions in here as well. The top vendors is quite common, but the
sheer amount of new drivers is uncommon, so I'm anticipating a larger
number of fixes for clk drivers this cycle.
Core:
- devm_clk_bulk_get_all_enabled() to return number of clks acquired
- devm_clk_hw_register_gate_parent_hw() helper to modernize drivers
- KUnit tests for clk-assigned-rates{,-u64}
New Drivers:
- Marvell PXA1908 SoC clks
- Mobileye EyeQ5, EyeQ6L and EyeQ6H clk driver
- TWL6030 clk driver
- Nuvoton Arbel BMC NPCM8XX SoC clks
- MediaTek MT6735 SoC clks
- MediaTek MT7620, MT7628 and MT7688 MMC clks
- Add a driver for gated fixed rate clocks
- Global clock controllers for Qualcomm QCS8300 and IPQ5424 SoCs
- Camera, display and video clock controllers for Qualcomm SA8775P
SoCs
- Global, display, GPU, TCSR, and RPMh clock controllers for Qualcomm
SAR2130P
- Global, camera, display, GPU, and video clock controllers for
Qualcomm SM8475 SoCs
- RTC power domain and Battery Backup Function (VBATTB) clock support
for the Renesas RZ/G3S SoC
- Qualcomm IPQ9574 alpha PLLs
- Support for i.MX91 CCM in the i.MX93 driver
- Microchip LAN969X SoC clks
- Cortex-A55 core clocks and Interrupt Control Unit (ICU) clock and
reset on Renesas RZ/V2H(P)
- Samsung ExynosAutov920 clk drivers for PERIC1, MISC, HSI0 and HSI1
- Samsung Exynos8895 clk drivers for FSYS0/1, PERIC0/1, PERIS and TOP
Updates:
- Convert more clk bindings to YAML
- Various clk driver cleanups: NULL checks, add const, etc.
- Remove END/NUM #defines that count number of clks in various
binding headers
- Continue moving reset drivers to drivers/reset via auxiliary bus"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (162 commits)
clk: clk-loongson2: Fix potential buffer overflow in flexible-array member access
clk: Fix invalid execution of clk_set_rate
clk: clk-loongson2: Fix memory corruption bug in struct loongson2_clk_provider
clk: lan966x: make it selectable for ARCH_LAN969X
clk: eyeq: add EyeQ6H west fixed factor clocks
clk: eyeq: add EyeQ6H central fixed factor clocks
clk: eyeq: add EyeQ5 fixed factor clocks
clk: eyeq: add fixed factor clocks infrastructure
clk: eyeq: require clock index with phandle in all cases
clk: fixed-factor: add clk_hw_register_fixed_factor_index() function
dt-bindings: clock: eyeq: add more Mobileye EyeQ5/EyeQ6H clocks
dt-bindings: soc: mobileye: set `#clock-cells = <1>` for all compatibles
clk: clk-axi-clkgen: make sure to enable the AXI bus clock
dt-bindings: clock: axi-clkgen: include AXI clk
clk: mmp: Add Marvell PXA1908 MPMU driver
clk: mmp: Add Marvell PXA1908 APMU driver
clk: mmp: Add Marvell PXA1908 APBCP driver
clk: mmp: Add Marvell PXA1908 APBC driver
dt-bindings: clock: Add Marvell PXA1908 clock bindings
clk: mmp: Switch to use struct u32_fract instead of custom one
...
tps65010, have undergone minor code improvements to enhance consistency and
fix race conditions.
- The syscon driver now utilizes the regmap max_register_is_0 capability
for consistent register map configuration across syscons of all sizes.
- New device support has been added for QCS8300, qcs615, SA8255p, and
samsung,s2dos05, expanding the range of compatible hardware.
- The cros_ec driver now supports loading cros_ec_ucsi on supported ECs
and avoids loading the charger with UCSI, streamlining functionality.
- The bd96801 driver now utilizes the more modern maple tree register
cache, improving performance.
- The da9052-spi driver has undergone a fix to change the read-mask to
write-mask, preventing potential issues.
- Unused declarations in max77693 have been removed, and support for
samsung,s2dos05 has been added, enhancing code clarity and device compatibility.
- Error handling in cs42l43 has been fixed to avoid unbalanced regulator
put and ensure proper synchronization during driver removal.
- The wcd934x driver now uses MODULE_DEVICE_TABLE() instead of
MODULE_ALIAS(), improving code consistency.
- Documentation for qcom,tcsr, syscon, and atmel-smc has been updated
and reorganized for better clarity and maintainability.
- The intel_soc_pmic_bxtwc driver has undergone significant improvements,
including the use of IRQ domains for various devices, fixing IRQ domain names
duplication, and code refactoring for better consistency and maintainability.
- The ipaq-micro driver has received a fix for a missing break statement in
the default case, enhancing code robustness.
- Support for the AXP323 PMIC has been added to the axp20x driver, along
with ensuring a clear relationship between IDs and model names, and allowing
multiple regulators, broadening hardware compatibility.
- The cs42l43 driver now disables IRQs during suspend for improved power
management.
- The adp5585 driver has reduced its dependencies by dropping the obsolete
dependency on COMPILE_TEST.
- Initial support for the MT6328 PMIC has been added to the mt6397 driver,
expanding the range of supported hardware.
- The rtc-bd70528 driver has been simplified by dropping the IC name from
IRQ, improving code readability.
- Documentation for qcom,spmi-pmic, ti,twl, and zii,rave-sp has been
updated to enhance clarity and incorporate new features.
- The rt5033 driver has received a fix for a missing regmap_del_irq_chip()
in the error handling path.
- New device support has been added for MSM8917, and the
intel_soc_pmic_crc driver now supports non-ACPI instantiated i2c_client.
- The 88pm886 driver has added support for the RTC cell, and the tqmx86
driver has improved its GPIO IRQ setup and added I2C IRQ support,
increasing functionality.
- The sprd,sc2731 DT schema has been updated and converted to YAML format
for better readability and maintainability.
-----BEGIN PGP SIGNATURE-----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=YP3r
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
- Several drivers, including atmel-flexcom/rk8xx-core, palmas, and
tps65010, have undergone minor code improvements to enhance
consistency and fix race conditions.
- The syscon driver now utilizes the regmap max_register_is_0
capability for consistent register map configuration across syscons
of all sizes.
- New device support has been added for QCS8300, qcs615, SA8255p, and
samsung,s2dos05, expanding the range of compatible hardware.
- The cros_ec driver now supports loading cros_ec_ucsi on supported ECs
and avoids loading the charger with UCSI, streamlining functionality.
- The bd96801 driver now utilizes the more modern maple tree register
cache, improving performance.
- The da9052-spi driver has undergone a fix to change the read-mask to
write-mask, preventing potential issues.
- Unused declarations in max77693 have been removed, and support for
samsung,s2dos05 has been added, enhancing code clarity and device
compatibility.
- Error handling in cs42l43 has been fixed to avoid unbalanced
regulator put and ensure proper synchronization during driver
removal.
- The wcd934x driver now uses MODULE_DEVICE_TABLE() instead of
MODULE_ALIAS(), improving code consistency.
- Documentation for qcom,tcsr, syscon, and atmel-smc has been updated
and reorganized for better clarity and maintainability.
- The intel_soc_pmic_bxtwc driver has undergone significant
improvements, including the use of IRQ domains for various devices,
fixing IRQ domain names duplication, and code refactoring for better
consistency and maintainability.
- The ipaq-micro driver has received a fix for a missing break
statement in the default case, enhancing code robustness.
- Support for the AXP323 PMIC has been added to the axp20x driver,
along with ensuring a clear relationship between IDs and model names,
and allowing multiple regulators, broadening hardware compatibility.
- The cs42l43 driver now disables IRQs during suspend for improved
power management.
- The adp5585 driver has reduced its dependencies by dropping the
obsolete dependency on COMPILE_TEST.
- Initial support for the MT6328 PMIC has been added to the mt6397
driver, expanding the range of supported hardware.
- The rtc-bd70528 driver has been simplified by dropping the IC name
from IRQ, improving code readability.
- Documentation for qcom,spmi-pmic, ti,twl, and zii,rave-sp has been
updated to enhance clarity and incorporate new features.
- The rt5033 driver has received a fix for a missing
regmap_del_irq_chip() in the error handling path.
- New device support has been added for MSM8917, and the
intel_soc_pmic_crc driver now supports non-ACPI instantiated
i2c_client.
- The 88pm886 driver has added support for the RTC cell, and the tqmx86
driver has improved its GPIO IRQ setup and added I2C IRQ support,
increasing functionality.
- The sprd,sc2731 DT schema has been updated and converted to YAML
format for better readability and maintainability.
* tag 'mfd-next-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (62 commits)
dt-bindings: mfd: bd71828: Use charger resistor in mOhm instead of MOhm
dt-bindings: mfd: sprd,sc2731: Convert to YAML
mfd: tqmx86: Add I2C IRQ support
mfd: tqmx86: Make IRQ setup errors non-fatal
mfd: tqmx86: Refactor GPIO IRQ setup
mfd: tqmx86: Improve gpio_irq module parameter description
mfd: tqmx86: Add board definitions for TQMx120UC, TQMx130UC and TQMxE41S
mfd: 88pm886: Add the RTC cell
dt-bindings: mfd: Add Realtek RTL9300 switch peripherals
mfd: intel_soc_pmic_crc: Add support for non ACPI instantiated i2c_client
mfd: intel_soc_pmic_*: Consistently use filename as driver name
dt-bindings: mfd: qcom,tcsr: Add compatible for MSM8917
mfd: rt5033: Fix missing regmap_del_irq_chip()
mfd: cgbc-core: Fix error handling paths in cgbc_init_device()
dt-bindings: mfd: aspeed: Support for AST2700
mfd: Switch back to struct platform_driver::remove()
dt-bindings: mfd: qcom,spmi-pmic: Document PMICs added in SM8750
mfd: rtc: bd7xxxx Drop IC name from IRQ
mfd: mt6397: Add initial support for MT6328
mfd: adp5585: Drop obsolete dependency on COMPILE_TEST
...
Add dt bindings and documentation for the Marvell PXA1908 clock
controller.
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Duje Mihanović <duje.mihanovic@skole.hr>
Link: https://lore.kernel.org/r/20241104-pxa1908-lkml-v13-4-e050609b8d6c@skole.hr
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add device tree bindings for syscon clock and reset controllers (IMGSYS,
MFGCFG, VDECSYS and VENCSYS).
Signed-off-by: Yassine Oudjana <y.oudjana@protonmail.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20241106111402.200940-2-y.oudjana@protonmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Introduce descriptions of the 8cx Gen3-based Microsoft Surface Pro 9 5G,
X Elite based Dell XPS 13 9345, the QCS9100 platform and the "Ride"
development boards thereon, and the SM7325 platform and the Nothing
Phone 1.
MSM8998 gains support for HDMI. The Lenovo Miix 630 gains support for
volume keys, audio and sensor DSPs, touchscreen, and its specific WiFi
calibration variant.
On QCM6490, Fairphone FP5 gains a thermistor adjacent to UFS/RAM, while
the IDP gains UFS and WiFi support. For QCS6490 changes to Rb3Gen2
enables WiFi, Venus, PCIe, SD-card, and volume keys. Adreno speedbins
are adjusted and PMU nodes' compatibles for the two clusters are
corrected.
The DB845C/RB3 and QRB5165 RB5 vision mezzanines are converted to
DeviceTree overlays, and both gains CMA heap for libcamera to use.
SA8775P gains GPI DMA support, support for controlling download mode
(bootloader-assisted ramdump support), additional UARTs, and qcrypto
support. The "Ride" development board gains WiFi and Bluetooth support.
On SC8280XP (8cx Gen3) another UART is described, used in the
Microsoft Surface 9 5G. The WiFi/BT combo chip's power management unit
is described on the CRD and Lenovo ThinkPad X13s.
On SDM630/660 the GPU SMMU and clock controller is added, as is the
A2Noc and LPASS SMMU, and the DSP-based WiFi device. GPU, modem DSP and
WiFi is then enabled on the Inforce 6560 development board.
On SM8450 Hardware Development Kit, the WCN6855 is modelled to enable
WiFi and Bluetooth. A "global" interrupt is defined on SM8450 PCIe RC
controller, to enable hotplug.
On X Elite, USB Type-C controllers are marked as usb-role-switch
capable, the GICv3 ITS is enabled for PCIe. TCSR region is described and
wired up to allow setting and cleaning the download mode
(bootloader-assisted ramdump) flag, and residency numbers for C4/C5 are
updated.
USB role switch is enabled on Lenovo ThinkPad T14s and the ASUS Vivobook
S15. The T14s also gains support for a second source trackpad. The
Microsoft Surface Laptop gains LID switch and the USB Type-A connector
attached to the multiport controller is enabled. The CRD has its HID
device power supplies described.
Application SMMU is flagged as DMA coherent across QDU1000, SC7180,
SC8180X, SC8280XP, SDM670, SDM845, SM8150, SM8350, SM8450, and X1E80100.
In addition to this, the effort to improve style and binding compliance
continued.
-----BEGIN PGP SIGNATURE-----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=Qu8Z
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEiK/NIGsWEZVxh/FrYKtH/8kJUicFAmczzIIACgkQYKtH/8kJ
UidW2A//U7s3EZaJdA4cL6wT3SCb1IGdU4DzsALPJuVlRiQuCiT4C+r/9+k7p6vf
4sny9ZvvadjtM9Goext4T40rVjw00kcgpI3tE3UzEgDr6yws/7AnpI8/Oo7A2Kd3
1vn2OBeRMS+HqQKhyjZ2rAtMnSUw7aQ69tVCbc5YeWPN3Tj4dI0/Agg12RZSuz3B
75aVDiURhzcPTDsnywYXaEzDH0Jkk4+wcmIMk5ll28s+lOlL2YjEGeLeoBFriJss
4tv4ir5blhlMMWFPRif9cxp1msrd+7nLYBKtBW/65+If5Od3aCg0I6H7beMAFRCr
H2mO0RadU/E7Q00i8pT48/5/vaDFpyEuvdxRdq4LVkfoqOVnIvj+hV7BMrQpudyy
/0R1+13FNjKrBI/4UcgaZH06N/i0A296Sxj53jEDgoB/hqr4XpzzrrxvApu44BEU
dJLGr2LEOe7+rfhXcu8kRwtuza6F0gYL5SfL1zNGfcdSeUNyKd/9j1FqTvmJsBSW
5zZfgHuiuGb86FSOvIXhEIxKyC19aO8El8tiqGOX2e8HsG23pLJTS6yUQqGxlvt6
2WSwIzgn7XBOAaCePcVDkpau5rpcqNt2X5Ka9+M2ebXdInjRPHXA9G0LBUbrHYvU
LcCtK0m7wyDkQYIwuDEBg/xsrg4hpRsvCV5DRR6oD9jtixGnWRU=
=JBWR
-----END PGP SIGNATURE-----
Merge tag 'qcom-arm64-for-6.13' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into soc/dt
Qualcomm Arm64 DeviceTree changes for v6.13
Introduce descriptions of the 8cx Gen3-based Microsoft Surface Pro 9 5G,
X Elite based Dell XPS 13 9345, the QCS9100 platform and the "Ride"
development boards thereon, and the SM7325 platform and the Nothing
Phone 1.
MSM8998 gains support for HDMI. The Lenovo Miix 630 gains support for
volume keys, audio and sensor DSPs, touchscreen, and its specific WiFi
calibration variant.
On QCM6490, Fairphone FP5 gains a thermistor adjacent to UFS/RAM, while
the IDP gains UFS and WiFi support. For QCS6490 changes to Rb3Gen2
enables WiFi, Venus, PCIe, SD-card, and volume keys. Adreno speedbins
are adjusted and PMU nodes' compatibles for the two clusters are
corrected.
The DB845C/RB3 and QRB5165 RB5 vision mezzanines are converted to
DeviceTree overlays, and both gains CMA heap for libcamera to use.
SA8775P gains GPI DMA support, support for controlling download mode
(bootloader-assisted ramdump support), additional UARTs, and qcrypto
support. The "Ride" development board gains WiFi and Bluetooth support.
On SC8280XP (8cx Gen3) another UART is described, used in the
Microsoft Surface 9 5G. The WiFi/BT combo chip's power management unit
is described on the CRD and Lenovo ThinkPad X13s.
On SDM630/660 the GPU SMMU and clock controller is added, as is the
A2Noc and LPASS SMMU, and the DSP-based WiFi device. GPU, modem DSP and
WiFi is then enabled on the Inforce 6560 development board.
On SM8450 Hardware Development Kit, the WCN6855 is modelled to enable
WiFi and Bluetooth. A "global" interrupt is defined on SM8450 PCIe RC
controller, to enable hotplug.
On X Elite, USB Type-C controllers are marked as usb-role-switch
capable, the GICv3 ITS is enabled for PCIe. TCSR region is described and
wired up to allow setting and cleaning the download mode
(bootloader-assisted ramdump) flag, and residency numbers for C4/C5 are
updated.
USB role switch is enabled on Lenovo ThinkPad T14s and the ASUS Vivobook
S15. The T14s also gains support for a second source trackpad. The
Microsoft Surface Laptop gains LID switch and the USB Type-A connector
attached to the multiport controller is enabled. The CRD has its HID
device power supplies described.
Application SMMU is flagged as DMA coherent across QDU1000, SC7180,
SC8180X, SC8280XP, SDM670, SDM845, SM8150, SM8350, SM8450, and X1E80100.
In addition to this, the effort to improve style and binding compliance
continued.
* tag 'qcom-arm64-for-6.13' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (120 commits)
arm64: dts: qcom: sdm845-db845c-navigation-mezzanine: Add cma heap for libcamera softisp support
arm64: dts: qcom: qrb5165-rb5-vision-mezzanine: Add cma heap for libcamera softisp support
arm64: dts: qcom: qrb5165-rb5-vision-mezzanine: Drop redundant clock-lanes from camera@1a
arm64: dts: qcom: sc8280xp-x13s: Drop redundant clock-lanes from camera@10
arm64: dts: qcom: sdm845-db845c-navigation-mezzanine: Convert mezzanine riser to dtso
arm64: dts: qcom: qrb5165-rb5-vision-mezzanine: Convert mezzanine riser to dtbo
arm64: dts: qcom: sm8450-hdk: model the PMU of the on-board wcn6855
arm64: dts: qcom: sc8280xp-x13s: model the PMU of the on-board wcn6855
arm64: dts: qcom: sc8280xp-crd: enable bluetooth
arm64: dts: qcom: sc8280xp-crd: model the PMU of the on-board wcn6855
arm64: dts: qcom: qcs9100: Add support for the QCS9100 Ride and Ride Rev3 boards
dt-bindings: arm: qcom: Document qcs9100-ride and qcs9100-ride Rev3
arm64: dts: qcom: x1e80100: Update C4/C5 residency/exit numbers
arm64: dts: qcom: x1e80100-crd: describe HID supplies
arm64: dts: qcom: msm8998-lenovo-miix-630: add WiFi calibration variant
arm64: dts: qcom: msm8998-clamshell: enable resin/VolDown
arm64: dts: qcom: msm8998-lenovo-miix-630: enable VolumeUp button
arm64: dts: qcom: msm8998-lenovo-miix-630: enable aDSP and SLPI
arm64: dts: qcom: msm8998-lenovo-miix-630: enable touchscreen
arm64: dts: qcom: qcs6490-rb3gen2: Add PCIe nodes
...
Link: https://lore.kernel.org/r/20241105164901.7787-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Add a CPU Operating Performance Points table for the RZ/V2H SoC,
- Add Battery Backup Function (VBATTB) and RTC support for the RZ/G3S
SoC and the RZ/G3S SMARC SoM,
- Add DMAC support for MMC on the RZ/A1H SoC and the Genmai
development board,
- Miscellaneous fixes and improvements.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCZyjGagAKCRCKwlD9ZEnx
cHrRAPsETRczaN2vpy+9m0EJuN+QhlX980jiLYndIx8YUvMG3QD/XdLdG4MnGQtg
2x8u2BfbbXOIrV2YWErVIVn/bQNAMgk=
=FjWC
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=7QOY
-----END PGP SIGNATURE-----
Merge tag 'renesas-dts-for-v6.13-tag2' of https://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into soc/dt
Renesas DTS updates for v6.13 (take two)
- Add a CPU Operating Performance Points table for the RZ/V2H SoC,
- Add Battery Backup Function (VBATTB) and RTC support for the RZ/G3S
SoC and the RZ/G3S SMARC SoM,
- Add DMAC support for MMC on the RZ/A1H SoC and the Genmai
development board,
- Miscellaneous fixes and improvements.
* tag 'renesas-dts-for-v6.13-tag2' of https://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
arm64: dts: renesas: rzg3s-smarc-som: Enable RTC
arm64: dts: renesas: rzg3s-smarc-som: Enable VBATTB
arm64: dts: renesas: r9a08g045: Add RTC node
arm64: dts: renesas: r9a08g045: Add VBATTB node
arm64: dts: renesas: white-hawk-cpu-common: Add pin control for DSI-eDP IRQ
ARM: dts: renesas: r7s72100: Add DMA support to MMCIF
ARM: dts: renesas: r7s72100: Add DMAC node
arm64: dts: renesas: hihope: Drop #sound-dai-cells
dt-bindings: clock: renesas,r9a08g045-vbattb: Document VBATTB
dt-bindings: clock: r9a08g045-cpg: Add power domain ID for RTC
arm64: dts: renesas: r9a09g057: Add OPP table
Link: https://lore.kernel.org/r/cover.1730726155.git.geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add support for qcom global clock controller bindings for QCS8300 platform.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Imran Shaik <quic_imrashai@quicinc.com>
Link: https://lore.kernel.org/r/20240822-qcs8300-gcc-v2-1-b310dfa70ad8@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add bindings for the Global Clock Controller (GCC) present on the
Qualcomm SAR2130P platform.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20241027-sar2130p-clocks-v5-2-ecad2a1432ba@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The VBATTB IP of the Renesas RZ/G3S SoC controls the clock for RTC,
the tamper detector and a small general usage memory of 128B.
The VBATTB controller controls the clock for the RTC on the Renesas
RZ/G3S. The HW block diagram for the clock logic is as follows:
+----------+ XC `\
RTXIN --->| |----->| \ +----+ VBATTCLK
| 32K clock| | |----->|gate|----------->
| osc | XBYP | | +----+
RTXOUT --->| |----->| /
+----------+ ,/
One could connect as input to this HW block either a crystal or
an external clock device. This is board specific.
After discussions w/ Stephen Boyd the clock tree associated with this
hardware block was exported in Linux as:
input-xtal
xbyp
xc
mux
vbattclk
where:
- input-xtal is the input clock (connected to RTXIN, RTXOUT pins)
- xc, xbyp are mux inputs
- mux is the internal mux
- vbattclk is the gate clock that feeds in the end the RTC
to allow selecting the input of the MUX though assigned-clock DT
properties, using the already existing clock drivers and avoid adding
other DT properties.
This allows select the input of the mux based on the type of the
connected input clock:
- if the 32768 crystal is connected as input for the VBATTB,
the input of the mux should be xc
- if an external clock device is connected as input for the VBATTB the
input of the mux should be xbyp
Add bindings for the VBATTB controller.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/20241101095720.2247815-2-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add reset, clk dt bindings headers, and update compatible
support for AST2700 clk, silicon-id in yaml.
Signed-off-by: Ryan Chen <ryan_chen@aspeedtech.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20241023090153.1395220-2-ryan_chen@aspeedtech.com
Signed-off-by: Lee Jones <lee@kernel.org>
The RTC and VBATTB don't share the MSTOP control bit (but only the bus
clock and the reset signal). As the MSTOP control is modeled though power
domains add power domain ID for the RTC device available on the
Renesas RZ/G3S SoC.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20241019084738.3370489-2-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
i.MX91 has similar Clock Control Module(CCM) design as i.MX93, only add
few new clock compared to i.MX93.
Add a new compatible string and some new clocks for i.MX91.
Signed-off-by: Pengfei Li <pengfei.li_1@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20241023184651.381265-4-pengfei.li_1@nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
IMX93_CLK_END should be dropped as it is not part of the ABI.
Signed-off-by: Pengfei Li <pengfei.li_1@nxp.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20241023184651.381265-3-pengfei.li_1@nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Add clock definitions for the main clock and reset controllers of MT6735
(apmixedsys, topckgen, infracfg and pericfg).
Signed-off-by: Yassine Oudjana <y.oudjana@protonmail.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20241017071708.38663-2-y.oudjana@protonmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add peric1, misc and hsi0/1 clock definitions.
- CMU_PERIC1 for USI, IC2 and I3C
- CMU_MISC for MISC, GIC and OTP
- HSI0 for PCIE
- HSI1 for USB and MMC
Signed-off-by: Sunyeal Hong <sunyeal.hong@samsung.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20241009042110.2379903-2-sunyeal.hong@samsung.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Add new entry to the SM8450 dt-bindings and add SM8475-specific clocks
to SM8450 GCC header file.
Signed-off-by: Danila Tikhonov <danila@jiaxyga.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240818204348.197788-2-danila@jiaxyga.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Number of clocks supported by Linux drivers might vary - sometimes we
add new clocks, not exposed previously. Therefore these numbers of
clocks should not be in the bindings, as that prevents changing them.
Remove it entirely from the bindings, once Linux drivers stopped using
them.
Signed-off-by: Inbaraj E <inbaraj.e@samsung.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20240917094355.37887-3-inbaraj.e@samsung.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
This concludes a long journey towards replacing the old
board files with devictree description on the Cirrus Logic
EP93xx platform.
Nikita Shubin has been working on this for a long time,
for details see the last post on
https://lore.kernel.org/lkml/20240909-ep93xx-v12-0-e86ab2423d4b@maquefel.me/
-----BEGIN PGP SIGNATURE-----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=Y3Cd
-----END PGP SIGNATURE-----
Merge tag 'soc-ep93xx-dt-6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC update from Arnd Bergmann:
"Convert ep93xx to devicetree
This concludes a long journey towards replacing the old board files
with devictree description on the Cirrus Logic EP93xx platform.
Nikita Shubin has been working on this for a long time, for details
see the last post on
https://lore.kernel.org/lkml/20240909-ep93xx-v12-0-e86ab2423d4b@maquefel.me/"
* tag 'soc-ep93xx-dt-6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (47 commits)
dt-bindings: gpio: ep9301: Add missing "#interrupt-cells" to examples
MAINTAINERS: Update EP93XX ARM ARCHITECTURE maintainer
soc: ep93xx: drop reference to removed EP93XX_SOC_COMMON config
net: cirrus: use u8 for addr to calm down sparse
dmaengine: cirrus: use snprintf() to calm down gcc 13.3.0
dmaengine: ep93xx: Fix a NULL vs IS_ERR() check in probe()
pinctrl: ep93xx: Fix raster pins typo
spi: ep93xx: update kerneldoc comments for ep93xx_spi
clk: ep93xx: Fix off by one in ep93xx_div_recalc_rate()
clk: ep93xx: add module license
dmaengine: cirrus: remove platform code
ASoC: cirrus: edb93xx: Delete driver
ARM: ep93xx: soc: drop defines
ARM: ep93xx: delete all boardfiles
ata: pata_ep93xx: remove legacy pinctrl use
pwm: ep93xx: drop legacy pinctrl
ARM: ep93xx: DT for the Cirrus ep93xx SoC platforms
ARM: dts: ep93xx: Add EDB9302 DT
ARM: dts: ep93xx: add ts7250 board
ARM: dts: add Cirrus EP93XX SoC .dtsi
...
Block comments should align the * on each line, as checkpatch rightfully
pointed out, so fix that style issue on the newly added rk3576 headers.
Fixes: 49c04453db ("dt-bindings: clock, reset: Add support for rk3576")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20240909223149.85364-1-heiko@sntech.de
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Document the device tree bindings for the Renesas RZ/V2H(P) SoC
Clock Pulse Generator (CPG).
CPG block handles the below operations:
- Generation and control of clock signals for the IP modules
- Generation and control of resets
- Control over booting
- Low power consumption and power supply domains
Also define constants for the core clocks of the RZ/V2H(P) SoC. Note the
core clocks are a subset of the ones which are listed as part of section
4.4.2 of HW manual Rev.1.01 which cannot be controlled by CLKON register.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20240729202645.263525-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add clock and reset ID defines for rk3576.
Compared to the downstream bindings written by Elaine, this uses
continous gapless IDs starting at 0. Thus all numbers are
different between downstream and upstream, but names are kept
exactly the same.
Also add documentation for the rk3576 CRU core.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com>
Signed-off-by: Detlev Casanova <detlev.casanova@collabora.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/0102019199a76766-f3a2b53f-d063-458b-b0d1-dfbc2ea1893c-000000@eu-west-1.amazonses.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
CLK_NR_CLKS and CLKPMU_NR_CLKS should not be part of the binding.
Remove since the kernel code no longer uses it.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/a3292ed0-3489-4887-8567-40ea4983c592@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Merge updates to MSM8998 GCC binding include file through topic branch,
to make available the newly added constants to both clock and DeviceTree
branch.
Add definitions for the Q6 BIMC, LPASS core and adsp smmu clocks,
required to enable audio functionality on MSM8998.
Add the GDSC definitions for the LPASS_ADSP_GDSC and LPASS_CORE_GDSC
as a final step to enable the required clock tree for the lpass iommu
and for the audio dsp itself.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Marc Gonzalez <mgonzalez@freebox.fr>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20240814-lpass-v1-1-a5bb8f9dfa8b@freebox.fr
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add device tree bindings for the camera clock controller on
Qualcomm SM4450 platform.
Signed-off-by: Ajit Pandey <quic_ajipan@quicinc.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20240611133752.2192401-5-quic_ajipan@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add dpum clock definitions and compatibles.
Also used clock name 'bus' instead of full clock name
dout_clkcmu_dpum_bus like other board cmu schema (GS101).
Signed-off-by: Kwanghoon Son <k.son@samsung.com>
Link: https://lore.kernel.org/r/20240809-clk_dpum-v3-1-359decc30fe2@samsung.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Exynos7885 SoC has a DWC3 USB Controller with Exynos USB PHY which in
theory supports USB3 SuperSpeed, but is only used as USB2 in all known
devices.
These, of course, need some clocks.
Add indices for these clocks.
Signed-off-by: David Virag <virag.david003@gmail.com>
Link: https://lore.kernel.org/r/20240806121157.479212-4-virag.david003@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
The numbering in Exynos7885's FSYS CMU bindings has 4 duplicated by
accident, with the rest of the bindings continuing with 5.
Fix this by moving CLK_MOUT_FSYS_USB30DRD_USER to the end as 11.
Since CLK_MOUT_FSYS_USB30DRD_USER is not used in any device tree as of
now, and there are no other clocks affected (maybe apart from
CLK_MOUT_FSYS_MMC_SDIO_USER which the number was shared with, also not
used in a device tree), this is the least impactful way to solve this
problem.
Fixes: cd268e309c ("dt-bindings: clock: Add bindings for Exynos7885 CMU_FSYS")
Cc: stable@vger.kernel.org
Signed-off-by: David Virag <virag.david003@gmail.com>
Link: https://lore.kernel.org/r/20240806121157.479212-2-virag.david003@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Allow PLLADIV2 and LVDSPLL to be referenced as a PMC_TYPE_CORE
clock from phandle in DT for sam9x7 SoC family.
Signed-off-by: Varshini Rajendran <varshini.rajendran@microchip.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Link: https://lore.kernel.org/r/20240729070803.1990916-1-varshini.rajendran@microchip.com
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Document the device tree bindings for the Renesas RZ/V2H(P) SoC
Clock Pulse Generator (CPG).
CPG block handles the below operations:
- Generation and control of clock signals for the IP modules
- Generation and control of resets
- Control over booting
- Low power consumption and power supply domains
Also define constants for the core clocks of the RZ/V2H(P) SoC. Note the
core clocks are a subset of the ones which are listed as part of section
4.4.2 of HW manual Rev.1.01 which cannot be controlled by CLKON register.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20240729202645.263525-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Merge the SM8550/SM8650 display clock controller binding header file
merge through a topic branch, to ensure the bindings are kept in sync
between clock and DeviceTree source branches.
The display clock controller indices for SM8650 and SM8550 are
completely equal. Replace the header file for qcom,sm8650-dispcc with
the symlink to the qcom,sm8550-dispcc header file.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240717-dispcc-sm8550-fixes-v2-7-5c4a3128c40b@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add device tree bindings for the camera clock controller on
Qualcomm SM8150 platform.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Satya Priya Kakitapalli <quic_skakitap@quicinc.com>
Link: https://lore.kernel.org/r/20240731062916.2680823-7-quic_skakitap@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The USB multiport controller needs a few missing resets, describe them
in the binding.
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Link: https://lore.kernel.org/r/20240730-sc8180x-usb-mp-v2-1-a7dc4265b553@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add a constant for TMU PCLK clock. It acts simultaneously as an
interface clock (to access TMU registers) and an operating clock which
makes TMU IP-core functional.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20240723163311.28654-1-semen.protsenko@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
CLK_NR_CLKS should not be part of the binding.
Remove since the kernel code no longer uses it.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/6f21c09b-e8d2-4749-aca6-572c79df775d@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Merge SM8650 video and camera clock drivers through topic branch, to
make available the DeviceTree binding includes to the DeviceTree source
branches as well.
Add device tree bindings for the camera clock controller on
Qualcomm SM8650 platform.
Signed-off-by: Jagadeesh Kona <quic_jkona@quicinc.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Link: https://lore.kernel.org/r/20240602114439.1611-7-quic_jkona@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
SM8650 video clock controller has most clocks same as SM8450,
but it also has few additional clocks and resets. Add device tree
bindings for the video clock controller on Qualcomm SM8650 platform
by defining these additional clocks and resets on top of SM8450.
Signed-off-by: Jagadeesh Kona <quic_jkona@quicinc.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Link: https://lore.kernel.org/r/20240602114439.1611-3-quic_jkona@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The clock definitions in <dt-bindings/clock/r8a779?-clock.h> were
superseded by those in <dt-bindings/clock/r8a779?-cpg-mssr.h> a long
time ago.
The last DTS user of these files was removed in commit 362b334b17
("ARM: dts: r8a7791: Convert to new CPG/MSSR bindings") in v4.15.
Driver support for the old bindings was removed in commit
58256143cf ("clk: renesas: Remove R-Car Gen2 legacy DT clock
support") in v5.5, so there is no point to keep on carrying these.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/d4abb688d666be35e99577a25b16958cbb4c3c98.1718796005.git.geert+renesas@glider.be
CLK_NR_CLKS should not be part of the binding. Let's drop it, since
the kernel code no longer uses it either.
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20240606143401.32454-4-knaerzche@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the required clock bindings for the GPADC.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20240605172049.231108-2-macroalpha82@gmail.com
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Add bindings for the clock generator of divider/mux and gates working
for other subsystem than RP subsystem for Sophgo SG2042.
Signed-off-by: Chen Wang <unicorn_wang@outlook.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Add bindings for the gate clocks of RP subsystem for Sophgo SG2042.
Signed-off-by: Chen Wang <unicorn_wang@outlook.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Add bindings for the pll clocks for Sophgo SG2042.
Signed-off-by: Chen Wang <unicorn_wang@outlook.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Guo Ren <guoren@kernel.org>
QCA8386/QCA8084 includes the clock & reset controller that is
accessed by MDIO bus. Two work modes are supported, qca8386 works
as switch mode, qca8084 works as PHY mode.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Luo Jie <quic_luoj@quicinc.com>
Link: https://lore.kernel.org/r/20240605124541.2711467-3-quic_luoj@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The 'sys_pll' input is an optional clock that can be used to generate
'sys_pll_div16', which serves as one of the sources for the GEN clock.
Signed-off-by: Dmitry Rokosov <ddrokosov@salutedevices.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20240515185103.20256-5-ddrokosov@salutedevices.com
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
The 'syspll' PLL is a general-purpose PLL designed specifically for the
CPU clock. It is capable of producing output frequencies within the
range of 768MHz to 1536MHz.
The 'syspll_in' source clock is an optional parent connection from the
peripherals clock controller.
Signed-off-by: Dmitry Rokosov <ddrokosov@salutedevices.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20240515185103.20256-3-ddrokosov@salutedevices.com
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
The DPHY's APB clock is required to be exposed in order to be able to
enable it and access the phy's registers.
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20240509140653.168591-3-knaerzche@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add device tree bindings for the video clock controller on Qualcomm
SM7150 platform.
Signed-off-by: Danila Tikhonov <danila@jiaxyga.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20240505201038.276047-8-danila@jiaxyga.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add device tree bindings for the camera clock controller on Qualcomm
SM7150 platform.
Signed-off-by: Danila Tikhonov <danila@jiaxyga.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20240505201038.276047-6-danila@jiaxyga.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add device tree bindings for the display clock controller on Qualcomm
SM7150 platform.
Co-developed-by: David Wronek <david@mainlining.org>
Signed-off-by: David Wronek <david@mainlining.org>
Signed-off-by: Danila Tikhonov <danila@jiaxyga.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20240505201038.276047-4-danila@jiaxyga.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
drivers. And there's zero diff in the core clk framework. Instead we have new
clk drivers for STM and Sophgo, with Samsung^WGoogle in third for the diffstat
because they introduced HSI0 and HSI2 clk drivers for Google's GS101 SoC (high
speed interface things like PCIe, UFS, and MMC). Beyond those big diffs there's
the usual updates to various clk drivers for incorrect parent descriptions or
mising MODULE_DEVICE_TABLE()s, etc. Nothing in particular stands out as super
interesting here.
New Drivers:
- STM32MP257 SoC clk driver
- Airoha EN7581 SoC clk driver
- Sophgo CV1800B, CV1812H and SG2000 SoC clk driver
- Loongson-2k0500 and Loongson-2k2000 SoC clk driver
- Add HSI0 and HSI2 clock controllers for Google GS101
- Add i.MX95 BLK CTL clock driver
Updates:
- Allocate clk_ops dynamically for SCMI clk driver
- Add support in qcom RCG and RCG2 for multiple configurations for the same frequency
- Use above support for IPQ8074 NSS port 5 and 6 clocks to resolve issues
- Fix the Qualcomm APSS IPQ5018 PLL to fix boot failures of some boards
- Cleanups and fixes for Qualcomm Stromer PLLs
- Reduce max CPU frequency on Qualcomm APSS IPQ5018
- Fix Kconfig dependencies of Qualcomm SM8650 GPU and SC8280XP camera
clk drivers
- Make Qualcomm MSM8998 Venus clocks functional
- Cleanup downstream remnants related to DisplayPort across Qualcomm
SM8450, SM6350, SM8550, and SM8650
- Reuse the Huayra APSS register map on Qualcomm MSM8996 CBF PLL
- Use a specific Qualcomm QCS404 compatible for the otherwise generic
HFPLL
- Remove Qualcomm SM8150 CPUSS AHB clk as it is unused
- Remove an unused field in the Qualcomm RPM clk driver
- Add missing MODULE_DEVICE_TABLE to Qualcomm MSM8917 and MSM8953
global clock controller drivers
- Allow choice of manual or firmware-driven control over PLLs, needed
to fully implement CPU clock controllers on Exynos850
- Correct PLL clock IDs on ExynosAutov9
- Propagate certain clock rates to allow setting proper SPI clock
rates on Google GS101
- Mark certain Google GS101 clocks critical
- Convert old S3C64xx clock controller bindings to DT schema
- Add new PLL rate and missing mux on Rockchip rk3568
- Add missing reset line on Rockchip rk3588
- Removal of an unused field in struct rockchip_mmc_clock
- Amlogic s4/a1: add regmap maximum register for proper debugfs dump
- Amlogic s4: add MODULE_DEVICE_TABLE() on pll and periph controllers
- Amlogic pll driver: print clock name on lock error to help debug
- Amlogic vclk: finish dsi clock path support
- Amlogic license: fix occurence "GPL v2" as reported by checkpatch
- Add PM runtime support to i.MX8MP Audiomix
- Add DT schema for i.MX95 Display Master Block Control
- Convert to platform remove callback returning void for i.MX8MP
Audiomix
- Add SPI (MSIOF) and external interrupt (INTC-EX) clocks on Renesas R-Car V4M
- Add interrupt controller (PLIC) clock and reset on Renesas RZ/Five
- Prepare power domain support for Renesas RZ/G2L family members, and add
actual support on Renesas RZ/G3S SoC
- Add thermal, serial (SCIF), and timer (CMT/TMU) clocks on Renesas R-Car V4M
- Add additional constraints to Allwinner A64 PLL MIPI clock
- Fix autoloading sunxi-ng clocks when build as a module
-----BEGIN PGP SIGNATURE-----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=YoVJ
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"I'm actually surprised this time. There aren't any new Qualcomm SoC
clk drivers. And there's zero diff in the core clk framework.
Instead we have new clk drivers for STM and Sophgo, with
Samsung^WGoogle in third for the diffstat because they introduced HSI0
and HSI2 clk drivers for Google's GS101 SoC (high speed interface
things like PCIe, UFS, and MMC).
Beyond those big diffs there's the usual updates to various clk
drivers for incorrect parent descriptions or mising
MODULE_DEVICE_TABLE()s, etc. Nothing in particular stands out as super
interesting here.
New Drivers:
- STM32MP257 SoC clk driver
- Airoha EN7581 SoC clk driver
- Sophgo CV1800B, CV1812H and SG2000 SoC clk driver
- Loongson-2k0500 and Loongson-2k2000 SoC clk driver
- Add HSI0 and HSI2 clock controllers for Google GS101
- Add i.MX95 BLK CTL clock driver
Updates:
- Allocate clk_ops dynamically for SCMI clk driver
- Add support in qcom RCG and RCG2 for multiple configurations for
the same frequency
- Use above support for IPQ8074 NSS port 5 and 6 clocks to resolve
issues
- Fix the Qualcomm APSS IPQ5018 PLL to fix boot failures of some
boards
- Cleanups and fixes for Qualcomm Stromer PLLs
- Reduce max CPU frequency on Qualcomm APSS IPQ5018
- Fix Kconfig dependencies of Qualcomm SM8650 GPU and SC8280XP camera
clk drivers
- Make Qualcomm MSM8998 Venus clocks functional
- Cleanup downstream remnants related to DisplayPort across Qualcomm
SM8450, SM6350, SM8550, and SM8650
- Reuse the Huayra APSS register map on Qualcomm MSM8996 CBF PLL
- Use a specific Qualcomm QCS404 compatible for the otherwise generic
HFPLL
- Remove Qualcomm SM8150 CPUSS AHB clk as it is unused
- Remove an unused field in the Qualcomm RPM clk driver
- Add missing MODULE_DEVICE_TABLE to Qualcomm MSM8917 and MSM8953
global clock controller drivers
- Allow choice of manual or firmware-driven control over PLLs, needed
to fully implement CPU clock controllers on Exynos850
- Correct PLL clock IDs on ExynosAutov9
- Propagate certain clock rates to allow setting proper SPI clock
rates on Google GS101
- Mark certain Google GS101 clocks critical
- Convert old S3C64xx clock controller bindings to DT schema
- Add new PLL rate and missing mux on Rockchip rk3568
- Add missing reset line on Rockchip rk3588
- Removal of an unused field in struct rockchip_mmc_clock
- Amlogic s4/a1: add regmap maximum register for proper debugfs dump
- Amlogic s4: add MODULE_DEVICE_TABLE() on pll and periph controllers
- Amlogic pll driver: print clock name on lock error to help debug
- Amlogic vclk: finish dsi clock path support
- Amlogic license: fix occurence "GPL v2" as reported by checkpatch
- Add PM runtime support to i.MX8MP Audiomix
- Add DT schema for i.MX95 Display Master Block Control
- Convert to platform remove callback returning void for i.MX8MP
Audiomix
- Add SPI (MSIOF) and external interrupt (INTC-EX) clocks on Renesas
R-Car V4M
- Add interrupt controller (PLIC) clock and reset on Renesas RZ/Five
- Prepare power domain support for Renesas RZ/G2L family members, and
add actual support on Renesas RZ/G3S SoC
- Add thermal, serial (SCIF), and timer (CMT/TMU) clocks on Renesas
R-Car V4M
- Add additional constraints to Allwinner A64 PLL MIPI clock
- Fix autoloading sunxi-ng clocks when build as a module"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (118 commits)
clk: samsung: Don't register clkdev lookup for the fixed rate clocks
clk, reset: microchip: mpfs: fix incorrect preprocessor conditions
clk: qcom: clk-alpha-pll: fix rate setting for Stromer PLLs
clk: qcom: apss-ipq-pll: fix PLL rate for IPQ5018
clk: qcom: Fix SM_GPUCC_8650 dependencies
clk: qcom: Fix SC_CAMCC_8280XP dependencies
dt-bindings: clocks: stm32mp25: add access-controllers description
clock, reset: microchip: move all mpfs reset code to the reset subsystem
clk: samsung: gs101: drop unused HSI2 clock parent data
clk: rockchip: rk3568: Add PLL rate for 724 MHz
clk: rockchip: Remove an unused field in struct rockchip_mmc_clock
dt-bindings: clock: fixed: Define a preferred node name
clk: meson: s4: fix module autoloading
clk: samsung: gs101: mark some apm UASC and XIU clocks critical
clk: imx: imx8mp: Convert to platform remove callback returning void
clk: imx: imx8mp: Switch to RUNTIME_PM_OPS()
clk: bcm: rpi: Assign ->num before accessing ->hws
clk: bcm: dvp: Assign ->num before accessing ->hws
clk: samsung: gs101: add support for cmu_hsi2
clk: samsung: gs101: add support for cmu_hsi0
...
Add dt schema documentation and clock IDs for the High Speed Interface
2 (HSI2) clock management unit. This CMU feeds high speed interfaces
such as PCIe and UFS.
[AD: * keep CMUs in google,gs101.h sorted alphabetically
* resolve minor merge conflicts in google,gs101-clock.yaml
* s/ufs_embd/ufs s/mmc_card/mmc
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Link: https://lore.kernel.org/r/20240429-hsi0-gs101-v3-1-f233be0a2455@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Add dt-schema documentation and clock IDs for the high speed interface
0 HSI0 clock management unit. This is used (amongst others) for USB.
While the usual (sed) script has been used to derive the linux clock
IDs from the data sheet, one manual tweak was applied to fix a typo
which we don't want to carry:
HSI0_USPDPDBG_USER -> HSI0_USBDPDBG_USER (note USB vs USP).
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20240423-hsi0-gs101-v1-1-2c3ddb50c720@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
In the new Loongson-2K family of SoCs, more clock indexes are needed,
such as clock gates.
The patch adds these clock indexes
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/76844e0e4dae290425f7c8025f7f36810cb3a3a8.1712731524.git.zhoubinbin@loongson.cn
Acked-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The USB480M clock can source from a MUX that selects the clock to come
from either of the USB-phy internal 480MHz PLLs. These clocks are
provided by the USB phy driver. This adds the define for it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240405-clk-rk3568-usb480m-phy-mux-v1-1-6c89de20a6ff@pengutronix.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The M2 (CRU main clock), M3 (LCDC Video Clock), and AT (Cortex-A55 Debug
clock) core clocks are only present on RZ/G2UL, not on RZ/Five.
Annotate this in the comments, like is already done for module clocks
and resets.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/ffcdcd479c76b92f67481836a33ec86e97f85634.1708944903.git.geert+renesas@glider.be
Add device nodes for the Timer Units (TMU) on the R-Mobile APE6 SoC,
and the clocks serving them.
Note that TMU channels 1 and 2 are not added, as their interrupts are
not wired to the interrupt controller for the AP-System Core (INTC-SYS),
only to the interrupt controller for the AP-Realtime Core (INTC-RT).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/1a60832f3ba37afb4a5791f4e5db4610ab31beb3.1710864964.git.geert+renesas@glider.be
- Increase dev_id len for clkdev lookups
* clk-samsung: (25 commits)
clk: samsung: Add CPU clock support for Exynos850
clk: samsung: Pass mask to wait_until_mux_stable()
clk: samsung: Keep register offsets in chip specific structure
clk: samsung: Keep CPU clock chip specific data in a dedicated struct
clk: samsung: Pass register layout type explicitly to CLK_CPU()
clk: samsung: Pass actual CPU clock registers base to CPU_CLK()
clk: samsung: Group CPU clock functions by chip
clk: samsung: Use single CPU clock notifier callback for all chips
clk: samsung: Reduce params count in exynos_register_cpu_clock()
clk: samsung: Pull struct exynos_cpuclk into clk-cpu.c
clk: samsung: Improve clk-cpu.c style
dt-bindings: clock: exynos850: Add CMU_CPUCLK0 and CMU_CPUCL1
clk: samsung: gs101: add support for cmu_peric1
clk: samsung: gs101: drop extra empty line
dt-bindings: clock: google,gs101-clock: add PERIC1 clock management unit
clk: samsung: exynos850: Propagate SPI IPCLK rate change
clk: samsung: gs101: gpio_peric0_pclk needs to be kept on
clk: samsung: exynos850: Add PDMA clocks
dt-bindings: clock: tesla,fsd: Fix spelling mistake
clk: samsung: gs101: add support for cmu_peric0
...
* clk-imx:
clk: imx: imx8mp: Fix SAI_MCLK_SEL definition
clk: imx: scu: Use common error handling code in imx_clk_scu_alloc_dev()
clk: imx: composite-8m: Delete two unnecessary initialisations in __imx8m_clk_hw_composite()
clk: imx: composite-8m: Less function calls in __imx8m_clk_hw_composite() after error detection
* clk-rockchip:
clk: rockchip: rk3399: Allow to set rate of clk_i2s0_frac's parent
clk: rockchip: rk3588: use linked clock ID for GATE_LINK
clk: rockchip: rk3588: fix indent
clk: rockchip: rk3588: fix pclk_vo0grf and pclk_vo1grf
dt-bindings: clock: rk3588: add missing PCLK_VO1GRF
dt-bindings: clock: rk3588: drop CLK_NR_CLKS
clk: rockchip: rk3588: fix CLK_NR_CLKS usage
clk: rockchip: rk3568: Add PLL rate for 128MHz
* clk-clkdev:
clkdev: Update clkdev id usage to allow for longer names
* clk-rate-exclusive:
clk: Add a devm variant of clk_rate_exclusive_get()
Add PCLK_VO1GRF to complement PCLK_VO0GRF. This will be needed
for HDMI support.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20240126182919.48402-4-sebastian.reichel@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
CLK_NR_CLKS should not be part of the binding. Let's drop it, since
the kernel code no longer uses it either.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20240126182919.48402-3-sebastian.reichel@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Document CPU clock management unit compatibles and add corresponding
clock indices. Exynos850 has two CPU clusters (CL0 and CL1), each
containing 4 Cortex-A55 cores. CPU PLLs are generating main CPU clocks
for each cluster, and there are alternate ("switch") clocks that can be
used temporarily while re-configuring the PLL for the new rate. ACLK,
ATCLK, PCLKDBG and PERIPHCLK clocks are driving corresponding buses.
CLK_CLUSTERx_SCLK are actual leaf CPU clocks and should be used to
change CPU rates. Also some CoreSight clocks can be derived from
DBG_USER (debug clock).
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20240224202053.25313-2-semen.protsenko@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
