One USB3 roothub port may support link power management, while another
root port on the same xHC can't due to different retimers used for
the ports.
This is the case with Intel Alder Lake, and possible future platforms
where retimers used for USB4 ports cause too long exit latecy to
enable native USB3 lpm U1 and U2 states.
Add a flag in the xhci port structure to indicate if the port is
lpm_incapable, and check it while calculating exit latency.
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230116142216.1141605-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allow PCI hosts to check and tune roothub and port settings
before the hub is up and running.
This override is needed to turn off U1 and U2 LPM for some ports
based on per port ACPI _DSM, _UPC, or possibly vendor specific mmio
values for Intel xHC hosts.
Usb core calls the host update_hub_device once it creates a hub.
Entering U1 or U2 link power save state on ports with this limitation
will cause link to fail, turning the usb device unusable in that setup.
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230116142216.1141605-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to also limit the amount of soft reset retries for transaction
errors on streams in cases where the transaction error event doesn't point
to any specific TRB.
In these cases we don't know the TRB or stream ring, but we do know which
endpoint had the error.
To keep error counting simple and functional, move the current err_count
from ring structure to endpoint structure.
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20221130091944.2171610-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Systems based on Alder Lake P see significant boot time delay if
boot firmware tries to control usb ports in unexpected link states.
This is seen with self-powered usb devices that survive in U3 link
suspended state over S5.
A more generic solution to power off ports at shutdown was attempted in
commit 83810f84ec ("xhci: turn off port power in shutdown")
but it caused regression.
Add host specific XHCI_RESET_TO_DEFAULT quirk which will reset host and
ports back to default state in shutdown.
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20221024142720.4122053-3-mathias.nyman@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci used to test if link power management (LPM) capable USB2 devices
really could enter and exit L1 state link state.
Failed devices were added to a lpm_failed_dev list.
This feature was removed 9 years ago in
commit de68bab4fa ("usb: Don't enable USB 2.0 Link PM by default.")
but lpm_failed_dev member was still left.
Remove it now.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220921123450.671459-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The u32 command was added to struct xhci_hcd over 10 years ago in
commit 9777e3ce90 ("USB: xHCI: bus power management implementation")
It wasn't even used back then, so remove it.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220921123450.671459-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the USB fixes in here and this resolves the merge issue in:
drivers/usb/dwc3/gadget.c
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce XHCI_SUSPEND_RESUME_CLKS quirk as a means to suspend and resume
clocks if the hardware is capable of doing so. We assume that clocks will
be needed if the device may wake.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Link: https://lore.kernel.org/r/1660170455-15781-2-git-send-email-justinpopo6@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 83810f84ec.
Turning off port power in shutdown did cause issues such as a laptop not
proprly powering off, and some specific usb devies failing to enumerate the
subsequent boot after a warm reset.
So revert this.
Fixes: 83810f84ec ("xhci: turn off port power in shutdown")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220825150840.132216-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After xHC controller is started, either in probe or resume, it can take
a while before any of the connected usb devices are visible to the roothub
due to link training.
It's possible xhci driver loads, sees no acivity and suspends the host
before the USB device is visible.
In one testcase with a hotplugged xHC controller the host finally detected
the connected USB device and generated a wake 500ms after host initial
start.
If hosts didn't suspend the device duringe training it probablty wouldn't
take up to 500ms to detect it, but looking at specs reveal USB3 link
training has a couple long timeout values, such as 120ms
RxDetectQuietTimeout, and 360ms PollingLFPSTimeout.
So Add a 500ms grace period that keeps polling the roothub for 500ms after
start, preventing runtime suspend until USB devices are detected.
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220825150840.132216-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit cbf286e8ef ("xhci: fix unsafe memory usage in xhci tracing")
apparently missed one sprintf() call in xhci_decode_trb() -- replace
it with the snprintf() call as well...
Found by Linux Verification Center (linuxtesting.org) with the SVACE static
analysis tool.
Fixes: cbf286e8ef ("xhci: fix unsafe memory usage in xhci tracing")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220630124645.1805902-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If ports are not turned off in shutdown then runtime suspended
self-powered USB devices may survive in U3 link state over S5.
During subsequent boot, if firmware sends an IPC command to program
the port in DISCONNECT state, it will time out, causing significant
delay in the boot time.
Turning off roothub port power is also recommended in xhci
specification 4.19.4 "Port Power" in the additional note.
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220623111945.1557702-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The XHCI_RESET_EP_QUIRK was added in 2009 to support prototype xHC
hardware from Fresco Logic that needed an additional configure endpoint
command after a reset endpoint.
That hardware should not have made it to the market.
Now, 13 years later its about time we get rid of it.
quirk was added in commit ac9d8fe7c6 ("USB: xhci: Add quirk for Fresco
Logic xHCI hardware.")
Print a debug message about the removed quirk if against all odds we run
into this controller.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220511220450.85367-9-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'stop endpoint' command timer was started when a 'stop endpoint'
command was added to the command queue.
This can trigger unwanted timeouts if there are several pending commands
in the queue that xHC needs to handle first.
The generic command timer, which was added later than the 'stop endpoint'
timeout timer, times each command currently being handled by xHC hardware.
A timed out stop endpoint command was treated as a more severe issue than
other failed commands, so the separate stop endpoint timer was left
unchanged.
Use the generic command timer for stop endpoint commands. Identify if
the timed out command was a stop endpoint command in the generic handler,
and treat it with the same severity as earlier.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220511220450.85367-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch prepares xhci for the following scenario:
- If either of the root hubs has no ports, then omit shared hcd
- Main hcd can be USB3 if there are no USB2 ports
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220511220450.85367-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_decode_ctrl_ctx() returns the untouched buffer as-is if both "drop"
and "add" parameters are zero.
Fix the function to return an empty string in that case.
It was not immediately clear from the possible call chains whether this
issue is currently actually triggerable or not.
Note that before commit 4843b4b5ec ("xhci: fix even more unsafe memory
usage in xhci tracing") the result effect in the failure case was different
as a static buffer was used here, but the code still worked incorrectly.
Fixes: 90d6d5731d ("xhci: Add tracing for input control context")
Cc: stable@vger.kernel.org
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
commit 4843b4b5ec ("xhci: fix even more unsafe memory usage in xhci tracing")
Link: https://lore.kernel.org/r/20220303110903.1662404-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_decode_usbsts() is expected to return a zero-terminated string by
its only caller, xhci_stop_endpoint_command_watchdog(), which directly
logs the return value:
xhci_warn(xhci, "USBSTS:%s\n", xhci_decode_usbsts(str, usbsts));
However, if no recognized bits are set in usbsts, the function will
return without having called any sprintf() and therefore return an
untouched non-zero-terminated caller-provided buffer, causing garbage
to be output to log.
Fix that by always including the raw value in the output.
Note that before commit 4843b4b5ec ("xhci: fix even more unsafe memory
usage in xhci tracing") the result effect in the failure case was different
as a static buffer was used here, but the code still worked incorrectly.
Fixes: 9c1aa36efd ("xhci: Show host status when watchdog triggers and host is assumed dead.")
Cc: stable@vger.kernel.org
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220303110903.1662404-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_reset() timeout was increased from 250ms to 10 seconds in order to
give Renesas 720201 xHC enough time to get ready in probe.
xhci_reset() is called with interrupts disabled in other places, and
waiting for 10 seconds there is not acceptable.
Add a timeout parameter to xhci_reset(), and adjust it back to 250ms
when called from xhci_stop() or xhci_shutdown() where interrupts are
disabled, and successful reset isn't that critical.
This solves issues when deactivating host mode on platforms like SM8450.
For now don't change the timeout if xHC is reset in xhci_resume().
No issues are reported for it, and we need the reset to succeed.
Locking around that reset needs to be revisited later.
Additionally change the signed integer timeout parameter in
xhci_handshake() to a u64 to match the timeout value we pass to
readl_poll_timeout_atomic()
Fixes: 22ceac1912 ("xhci: Increase reset timeout for Renesas 720201 host.")
Cc: stable@vger.kernel.org
Reported-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reported-by: Pavan Kondeti <quic_pkondeti@quicinc.com>
Tested-by: Pavan Kondeti <quic_pkondeti@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220303110903.1662404-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Every lpm commmand, both for USB 2 and USB 3 devies used the same
xhci->lpm_command structure to change max exit latency.
xhci->lpm_command is only protected by a hcd->bandwidth mutex, which is
not enoungh as USB 2 and USB 3 devices are behind separate HCDs.
Simplify code and avoid unnecessary locking risks by allocating
separate command structures for each lpm command, just like with
all other commands.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220216095153.1303105-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Seen on a VLI VL805 PCIe to USB controller. For non-stream endpoints
at least, if the xHC halts on a particular TRB due to an error then
the DCS field in the Out Endpoint Context maintained by the hardware
is not updated with the current cycle state.
Using the quirk XHCI_EP_CTX_BROKEN_DCS and instead fetch the DCS bit
from the TRB that the xHC stopped on.
[ bjorn: rebased to v5.14-rc2 ]
Link: https://github.com/raspberrypi/linux/issues/3060
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211008092547.3996295-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Removes static char buffer usage in the following decode functions:
xhci_decode_ctrl_ctx()
xhci_decode_slot_context()
xhci_decode_usbsts()
xhci_decode_doorbell()
xhci_decode_ep_context()
Caller must provide a buffer to use.
In tracing use __get_str() as recommended to pass buffer.
Minor changes are needed in other xhci code as these functions are also
used elsewhere
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210820123503.2605901-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Removes static char buffer usage in the following decode functions:
xhci_decode_trb()
xhci_decode_ptortsc()
Caller must provide a buffer to use.
In tracing use __get_str() as recommended to pass buffer.
Minor chanes are needed in xhci debugfs code as these functions are also
used there. Changes include moving XHCI_MSG_MAX definititon from
xhci-trace.h to xhci.h
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210820123503.2605901-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit c950686b38 as the
patch series is causing build issues in linux-next at the moment.
Cc: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/YMuRcrE8xlWnFSWW@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Save a bit of power by not interrupting so often by default if
XHCI_AVOID_BEI quirk is set.
In normal cases the xhci driver will only generate an interrupt on the last
isochronous TRB of an URB. In a common UVC webcam usecase there are 32 TRBs
per URB.
if AVOID_BEI flag is set then xhci driver will force an interrupt every 8th
isoc TRB to make sure the event ring doesn't get too full.
This is however way too frequent in common single webcam use cases, causing
1000 interrupts/sec and thus poor powermanagement performance.
Instead start with interrupting every 32 isoc TRB, and halve it in case
event ring becomes half-full. Stop halving when reaching a rate of every
8th trb.
This is a one way solution. If interrupt rate is increased it will stay
high until driver is reloaded. The highest rate is the same as the old
default rate.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210617150354.1512157-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We don't want those around confusing people.
ERST_NUM_SEGS is used both when allocating event ring segments, and when
allocating entries in the event ring segment table (erst).
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210617150354.1512157-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Call onboard_hub_create/destroy_pdevs() from _probe()/_remove()
to create/destroy platform devices for onboard USB hubs that may
be connected to the root hub of the controller. These functions
are a NOP unless CONFIG_USB_ONBOARD_HUB=y/m.
Also add a field to struct xhci_hcd to keep track of the onboard hub
platform devices that are owned by the xHCI.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20210609150159.v12.4.I7a3a7d9d2126c34079b1cab87aa0b2ec3030f9b7@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The XHCI controller is required to enter D3hot rather than D3cold for AMD
s2idle on this hardware generation.
Otherwise, the 'Controller Not Ready' (CNR) bit is not being cleared by
host in resume and eventually this results in xhci resume failures during
the s2idle wakeup.
Link: https://lore.kernel.org/linux-usb/1612527609-7053-1-git-send-email-Prike.Liang@amd.com/
Suggested-by: Prike Liang <Prike.Liang@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Cc: stable <stable@vger.kernel.org> # 5.11+
Link: https://lore.kernel.org/r/20210527154534.8900-1-mario.limonciello@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some systems rt2800usb and mt7601u devices are unable to operate since
commit f8f80be501 ("xhci: Use soft retry to recover faster from
transaction errors")
Seems that some xHCI controllers can not perform Soft Retry correctly,
affecting those devices.
To avoid the problem add xhci->quirks flag that restore pre soft retry
xhci behaviour for affected xHCI controllers. Currently those are
AMD_PROMONTORYA_4 and AMD_PROMONTORYA_2, since it was confirmed
by the users: on those xHCI hosts issue happen and is gone after
disabling Soft Retry.
[minor commit message rewording for checkpatch -Mathias]
Fixes: f8f80be501 ("xhci: Use soft retry to recover faster from transaction errors")
Cc: <stable@vger.kernel.org> # 4.20+
Reported-by: Bernhard <bernhard.gebetsberger@gmx.at>
Tested-by: Bernhard <bernhard.gebetsberger@gmx.at>
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=202541
Link: https://lore.kernel.org/r/20210311115353.2137560-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently xhci-hcd.ko building depends on USB_XHCI_MTK, this
is not flexible for some cases. For example:
USB_XHCI_HCD is y, and USB_XHCI_MTK is m, then we can't
implement extended functions if only update xhci-mtk.ko
This patch is used to remove the dependence.
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/0b62e21ddfacc1c2874726dd27ccab80c993f303.1615170625.git.chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_find_new_dequeue_state() and xhci_queue_new_dequeue_state() are no
longer used afer introducing the move_dequeue_past_td() function.
also remove struct xhci_dequeue_state as its no longer used.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-26-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't queue both a reset endpoint command and a
set TR deq command at once when handling a halted endpoint.
split this into two steps.
Initially only queue a reset endpoint command, and then if needed queue a
set TR deq command in the reset endpoint handler.
Note: This removes the RESET_EP_QUIRK handling which was added in
commit ac9d8fe7c6 ("USB: xhci: Add quirk for Fresco Logic xHCI hardware.")
This quirk was added in 2009 for prototype xHCI hardware meant for
evaluation purposes only, and should not reach consumers.
This hardware could not handle two commands queued at once, and had
bad data in the output context after a reset endpoint command.
After this patch two command are no longer queued at once, so that
part is solved in this rewrite, but the workaround for bad data in the
output context solved by issuing an extra configure endpoint command is
bluntly removed.
Adding this workaround to the new rewrite just adds complexity, and I
think it's time to let this quirk go.
Print a debug message instead.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-22-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In cases where the TD can't be given back in current handler we want
to be able to store it until its time to return the TD.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-19-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of re-reading, masking and endianness correcting the same trb
several times to get the trb type from an event, just do it once and
store it in a local variable.
Also pass the trb_type directly to the vendor specific event handler,
avoiding one more similar read.
In addition to the security benefit this also cleans up the code
and helps readability.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-13-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When finishing a TD we walk the endpoint dequeue trb pointer
until it matches the last TRB of the TD.
TDs can contain over 100 TRBs, meaning we call a function 100 times,
do a few comparisons and increase a couple values for each of these calls,
all in interrupt context.
This can all be avoided by adding a pointer to the last TRB segment, and
a number of TRBs in the TD. So instead of walking through each TRB just
set the new dequeue segment, pointer, and number of free TRBs directly.
Getting rid of the while loop also reduces the risk of getting stuck in a
infinite loop in the interrupt handler. Loop relied on valid matching
dequeue and last_trb values to break.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-12-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The one case that used this function can use the
xhci_triad_to_transfer_ring() helper instead.
Avoid having several functions doing basically the same thing.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-9-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In several event handlers we need to find the right endpoint
structure from slot_id and ep_index in the event.
Add a helper for this, check that slot_id and ep_index are valid.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of passing slot id and endpoint index to
cleanup_halted_endpoint() pass the endpoint structure pointer
as it's already known.
Avoids again digging out the endpoint structure based on
slot id and endpoint index, and passing them along the
call chain for this purpose only.
Add slot_id to the virt_dev structure so that it
can easily be found from a virt_dev, or its child, the
virt_ep endpoint structure.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When handling transfer events the event is passed along the handling
callpath and parsed again in several occasions.
The event contains slot_id and endpoint index, from which the driver
endpoint structure can be found. There wasn't however a way to get the
endpoint index or parent usb device from this endpoint structure.
A lot of extra event parsing, and thus some DMA doublefetch cases,
and excess variables and code can be avoided by adding endpoint index
and parent usb virt device pointer to the endpoint structure.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210129130044.206855-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci-mtk needs XHCI_MTK_HOST quirk functions in add_endpoint() and
drop_endpoint() to handle its own sw bandwidth management.
It stores bandwidth data into an internal table every time
add_endpoint() is called, and drops those in drop_endpoint().
But when bandwidth allocation fails at one endpoint, all earlier
allocation from the same interface could still remain at the table.
This patch moves bandwidth management codes to check_bandwidth() and
reset_bandwidth() path. To do so, this patch also adds those functions
to xhci_driver_overrides and lets mtk-xhci to release all failed
endpoints in reset_bandwidth() path.
Fixes: 08e469de87 ("usb: xhci-mtk: supports bandwidth scheduling with multi-TT")
Signed-off-by: Ikjoon Jang <ikjn@chromium.org>
Link: https://lore.kernel.org/r/20210113180444.v6.1.Id0d31b5f3ddf5e734d2ab11161ac5821921b1e1e@changeid
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Synopsys xHC has an internal TRB cache of size TRB_CACHE_SIZE for
each endpoint. The default value for TRB_CACHE_SIZE is 16 for SS and 8
for HS. The controller loads and updates the TRB cache from the transfer
ring in system memory whenever the driver issues a start transfer or
update transfer command.
For chained TRBs, the Synopsys xHC requires that the total amount of
bytes for all TRBs loaded in the TRB cache be greater than or equal to 1
MPS. Or the chain ends within the TRB cache (with a last TRB).
If this requirement is not met, the controller will not be able to send
or receive a packet and it will hang causing a driver timeout and error.
This can be a problem if a class driver queues SG requests with many
small-buffer entries. The XHCI driver will create a chained TRB for each
entry which may trigger this issue.
This patch adds logic to the XHCI driver to detect and prevent this from
happening.
For every (TRB_CACHE_SIZE - 2), we check the total buffer size of
the SG list and if the last window of (TRB_CACHE_SIZE - 2) SG list length
and we don't make up at least 1 MPS, we create a temporary buffer to
consolidate full SG list into the buffer.
We check at (TRB_CACHE_SIZE - 2) window because it is possible that there
would be a link and/or event data TRB that take up to 2 of the cache
entries.
We discovered this issue with devices on other platforms but have not
yet come across any device that triggers this on Linux. But it could be
a real problem now or in the future. All it takes is N number of small
chained TRBs. And other instances of the Synopsys IP may have smaller
values for the TRB_CACHE_SIZE which would exacerbate the problem.
Signed-off-by: Tejas Joglekar <joglekar@synopsys.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20201208092912.1773650-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit uses the private data passed by parent device
to set the quirk for Synopsys xHC. This patch fixes the
SNPS xHC hang issue when the data is scattered across
small buffers which does not make atleast MPS size for
given TRB cache size of SNPS xHC.
Signed-off-by: Tejas Joglekar <joglekar@synopsys.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20201208092912.1773650-2-mathias.nyman@linux.intel.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some platform of AMD, S3 fails with HCE and SRE errors. To fix this,
need to disable a bit which is enable in sparse controller.
Cc: stable@vger.kernel.org #v4.19+
Signed-off-by: Sanket Goswami <Sanket.Goswami@amd.com>
Signed-off-by: Sandeep Singh <sandeep.singh@amd.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20201028203124.375344-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some DRD controllers (eg, dwc3 & cdns3) have PHY management at
their own driver to cover both device and host mode, so add one
priv quirk for such users to skip PHY management from HCD core.
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200918131752.16488-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some atypical users of xhci-pci might need to manually reset their xHCI
controller before starting the HCD setup. Check if a reset controller
device is available to the PCI bus and trigger a reset.
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20200629161845.6021-6-nsaenzjulienne@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The generic xhci ring allocations code needs struct xhci_hcd pointer, and
it allocates memory for the rings from dma pools created for the xhci
device.
In order to decouple xhci and DbC we have to create our own ring allocation
and free routines for DbC
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200723144530.9992-20-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
EP_STATE_MASK should be 0x7 instead of 0xf
xhci spec 6.2.3 shows that the EP state field in the endpoint context data
structure consist of bits [2:0].
The old value included a bit from the next field which fortunately is a
RsvdZ region. So hopefully this hasn't caused too much harm
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200624135949.22611-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some rensas controller like uPD720201 and uPD720202 need firmware to be
loaded. Add these devices in table and invoke renesas firmware loader
functions to check and load the firmware into device memory when
required.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20200514122039.300417-4-vkoul@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a class driver cancels its only URB then the endpoint ring buffer will
appear empty to the xhci driver. xHC hardware may still process cached
TRBs, and complete with a STALL, halting the endpoint.
This halted endpoint was not handled correctly by xhci driver as events on
empty rings were all assumed to be spurious events.
xhci driver refused to restart the ring with EP_HALTED flag set, so class
driver was never informed the endpoint halted even if it queued new URBs.
The host side of the endpoint needs to be reset, and dequeue pointer should
be moved in order to clear the cached TRBs and resetart the endpoint.
Small adjustments in finding the new dequeue pointer are needed to support
the case of stall on an empty ring and unknown current TD.
Cc: <stable@vger.kernel.org>
cc: Jeremy Compostella <jeremy.compostella@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200421140822.28233-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch corrects the SPDX License Identifier style in
header files related to USB host controller drivers.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Link: https://lore.kernel.org/r/20200404092135.GA4522@nishad
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Like U3 case, xHCI spec doesn't specify the upper bound of U0 transition
time. The 20ms is not enough for some devices.
Intead of polling PLS or PLC, we can facilitate the port change event to
know that the link transits to U0 is completed.
While at it, also separate U0 and U3 case to make the code cleaner.
[variable rename to u3exit, and skip completion for usb2 ports -Mathias ]
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200312144517.1593-8-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Additional debugging to show xHC USBSTS register when stop endpoint
command watchdog triggers and host is assumed dead.
useful to know the current status before the controller is stopped by
the xhci driver and everything is released and freed.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200312144517.1593-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Link: https://lore.kernel.org/r/20200220132017.GA29262@embeddedor
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci driver assumed that xHC controllers have at most one custom
supported speed table (PSI) for all usb 3.x ports.
Memory was allocated for one PSI table under the xhci hub structure.
Turns out this is not the case, some controllers have a separate
"supported protocol capability" entry with a PSI table for each port.
This means each usb3 roothub port can in theory support different custom
speeds.
To solve this, cache all supported protocol capabilities with their PSI
tables in an array, and add pointers to the xhci port structure so that
every port points to its capability entry in the array.
When creating the SuperSpeedPlus USB Device Capability BOS descriptor
for the xhci USB 3.1 roothub we for now will use only data from the
first USB 3.1 capable protocol capability entry in the array.
This could be improved later, this patch focuses resolving
the memory leak.
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reported-by: Sajja Venkateswara Rao <VenkateswaraRao.Sajja@amd.com>
Fixes: 47189098f8 ("xhci: parse xhci protocol speed ID list for usb 3.1 usage")
Cc: stable <stable@vger.kernel.org> # v4.4+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200211150158.14475-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit fc57313d10.
Marek reports that it breaks things:
This patch landed in today's linux-next (20200211) and causes
NULL pointer dereference during second suspend/resume cycle on
Samsung Exynos5422-based (arm 32bit) Odroid XU3lite board:
A more complete fix will be added soon.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fixes: fc57313d10 ("xhci: Fix memory leak when caching protocol extended capability PSI tables")
Cc: Paul Menzel <pmenzel@molgen.mpg.de>
Cc: Sajja Venkateswara Rao <VenkateswaraRao.Sajja@amd.com>
Cc: stable <stable@vger.kernel.org> # v4.4+
Cc: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci driver assumed that xHC controllers have at most one custom
supported speed table (PSI) for all usb 3.x ports.
Memory was allocated for one PSI table under the xhci hub structure.
Turns out this is not the case, some controllers have a separate
"supported protocol capability" entry with a PSI table for each port.
This means each usb3 roothub port can in theory support different custom
speeds.
To solve this, cache all supported protocol capabilities with their PSI
tables in an array, and add pointers to the xhci port structure so that
every port points to its capability entry in the array.
When creating the SuperSpeedPlus USB Device Capability BOS descriptor
for the xhci USB 3.1 roothub we for now will use only data from the
first USB 3.1 capable protocol capability entry in the array.
This could be improved later, this patch focuses resolving
the memory leak.
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reported-by: Sajja Venkateswara Rao <VenkateswaraRao.Sajja@amd.com>
Fixes: 47189098f8 ("xhci: parse xhci protocol speed ID list for usb 3.1 usage")
Cc: stable <stable@vger.kernel.org> # v4.4+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200210134553.9144-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Xhci driver cannot call pci_set_power_state() on non-pci xhci host
controllers. For example, NVIDIA Tegra XHCI host controller which acts
as platform device with XHCI_SPURIOUS_WAKEUP quirk set in some platform
hits this issue during shutdown.
Cc: <stable@vger.kernel.org>
Fixes: 638298dc66 ("xhci: Fix spurious wakeups after S5 on Haswell")
Signed-off-by: Henry Lin <henryl@nvidia.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20191211142007.8847-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trace when a register in the doorbell array is written,
both for host controller command doorbell and device doorbells,
including for which endpoint and stream
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1573836603-10871-3-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Software can set a Transfer State Preserve (TSP) flag to maintain
data toggle and sequence number when issuing a reset endpoint
command.
xhci driver is using TSP for soft retry, we want to show TSP usage
in tracing as well
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1567172356-12915-4-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A second regression was found in the immediate data transfer (IDT)
support which was added to 5.2 kernel
IDT is used to transfer small amounts of data (up to 8 bytes) in the
field normally used for data dma address, thus avoiding dma mapping.
If the data was not already dma mapped, then IDT support assumed data was
in urb->transfer_buffer, and did not take into accound that even
small amounts of data (8 bytes) can be in a scatterlist instead.
This caused a NULL pointer dereference when sg_dma_len() was used
with non-dma mapped data.
Solve this by not using IDT if scatter gather buffer list is used.
Fixes: 33e39350eb ("usb: xhci: add Immediate Data Transfer support")
Cc: <stable@vger.kernel.org> # v5.2
Reported-by: Maik Stohn <maik.stohn@seal-one.com>
Tested-by: Maik Stohn <maik.stohn@seal-one.com>
CC: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1564044861-1445-1-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A USB3 device needs to be reset and re-enumarated if the port it
connects to goes to a error state, with link state inactive.
There is no use in trying to recover failed transactions by resetting
endpoints at this stage. Tests show that in rare cases, after multiple
endpoint resets of a roothub port the whole host controller might stop
completely.
Several retries to recover from transaction error can happen as
it can take a long time before the hub thread discovers the USB3
port error and inactive link.
We can't reliably detect the port error from slot or endpoint context
due to a limitation in xhci, see xhci specs section 4.8.3:
"There are several cases where the EP State field in the Output
Endpoint Context may not reflect the current state of an endpoint"
and
"Software should maintain an accurate value for EP State, by tracking it
with an internal variable that is driven by Events and Doorbell accesses"
Same appears to be true for slot state.
set a flag to the corresponding slot if a USB3 roothub port link goes
inactive to prevent both queueing new URBs and resetting endpoints.
Reported-by: Rapolu Chiranjeevi <chiranjeevi.rapolu@intel.com>
Tested-by: Rapolu Chiranjeevi <chiranjeevi.rapolu@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB 2.0 specification chapter 11.17.5 says "as part of endpoint halt
processing for full-/low-speed endpoints connected via a TT, the host
software must use the Clear_TT_Buffer request to the TT to ensure
that the buffer is not in the busy state".
In our case, a full-speed speaker (ConferenceCam) is behind a high-
speed hub (ConferenceCam Connect), sometimes once we get STALL on a
request we may continue to get STALL with the folllowing requests,
like Set_Interface.
Here we invoke usb_hub_clear_tt_buffer() to send Clear_TT_Buffer
request to the hub of the device for the following Set_Interface
requests to the device to get ACK successfully.
Signed-off-by: Jim Lin <jilin@nvidia.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci immediate data transfer (IDT) support in 5.2-rc1 caused regression
on various Samsung Exynos boards with ASIX USB 2.0 ethernet dongle.
If the transfer buffer in the URB is already DMA mapped then IDT should
not be used. urb->transfer_dma will already contain a valid dma address,
and there is no guarantee the data in urb->transfer_buffer is valid.
The IDT support patch used urb->transfer_dma as a temporary storage,
copying data from urb->transfer_buffer into it.
Issue was solved by preventing IDT if transfer buffer is already dma
mapped, and by not using urb->transfer_dma as temporary storage.
Fixes: 33e39350eb ("usb: xhci: add Immediate Data Transfer support")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
CC: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add tracing for the add and drop bits in the input control context
used in Address device, configure endpoint, evaluate context commands.
The add and drop bits tell xHC which enpoints are added and dropped.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Immediate data transfers (IDT) allow the HCD to copy small chunks of
data (up to 8bytes) directly into its output transfer TRBs. This avoids
the somewhat expensive DMA mappings that are performed by default on
most URBs submissions.
In the case an URB was suitable for IDT. The data is directly copied
into the "Data Buffer Pointer" region of the TRB and the IDT flag is
set. Instead of triggering memory accesses the HC will use the data
directly.
The implementation could cover all kind of output endpoints. Yet
Isochronous endpoints are bypassed as I was unable to find one that
matched IDT's constraints. As we try to bypass the default DMA mappings
on URB buffers we'd need to find a Isochronous device with an
urb->transfer_buffer_length <= 8 bytes.
The implementation takes into account that the 8 byte buffers provided
by the URB will never cross a 64KB boundary.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 2f31a67f01 ("usb: xhci: Prevent bus suspend if a port connect
change or polling state is detected") was intended to prevent ports that
were still link training from being forced to U3 suspend state mid
enumeration.
This solved enumeration issues for devices with slow link training.
Turns out some devices are stuck in the link training/polling state,
and thus that patch will prevent suspend completely for these devices.
This is seen with USB3 card readers in some MacBooks.
Instead of preventing suspend, give some time to complete the link
training. On successful training the port will end up as connected
and enabled.
If port instead is stuck in link training the bus suspend will continue
suspending after 360ms (10 * 36ms) timeout (tPollingLFPSTimeout).
Original patch was sent to stable, this one should go there as well
Fixes: 2f31a67f01 ("usb: xhci: Prevent bus suspend if a port connect change or polling state is detected")
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As commented in the struct's definition there shouldn't be anything
underneath its 'priv[0]' member as it would break some macros.
The patch converts the broken_suspend into a bit-field and relocates it
next to to the rest of bit-fields.
Fixes: a7d57abcc8 ("xhci: workaround CSS timeout on AMD SNPS 3.0 xHC")
Reported-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that each root hub has their own bus_state strucure the
hcd_undex() used to get the correct bus_state strucure is
no longer needed.
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the bus_state structure under struct usb_hub.
We need a bus_state strucure for each roothub to keep track of suspend
related info for each port.
Instead of keeping an array of two bus_state structures right under
struct xhci, it makes more sense move them to the xhci_hub structure.
No functional changes.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is introduced for the pre-0.96 xHC controllers, and the driver only
support HW LPM for 1.0 and later controllers.It's not actually used now
and is thought not to be used in the future any more, so just remove it.
Signed-off-by: Zeng Tao <prime.zeng@hisilicon.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Occasionally AMD SNPS 3.0 xHC does not respond to
CSS when set, also it does not flag anything on SRE and HCE
to point the internal xHC errors on USBSTS register. This stalls
the entire system wide suspend and there is no point in stalling
just because of xHC CSS is not responding.
To work around this problem, if the xHC does not flag
anything on SRE and HCE, we can skip the CSS
timeout and allow the system to continue the suspend. Once the
system resume happens we can internally reset the controller
using XHCI_RESET_ON_RESUME quirk
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Sandeep Singh <Sandeep.Singh@amd.com>
cc: Nehal Shah <Nehal-bakulchandra.Shah@amd.com>
Cc: <stable@vger.kernel.org>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement workaround for ThunderX2 Errata-129 (documented in
CN99XX Known Issues" available at Cavium support site).
As per ThunderX2errata-129, USB 2 device may come up as USB 1
if a connection to a USB 1 device is followed by another connection to
a USB 2 device, the link will come up as USB 1 for the USB 2 device.
Resolution: Reset the PHY after the USB 1 device is disconnected.
The PHY reset sequence is done using private registers in XHCI register
space. After the PHY is reset we check for the PLL lock status and retry
the operation if it fails. From our tests, retrying 4 times is sufficient.
Add a new quirk flag XHCI_RESET_PLL_ON_DISCONNECT to invoke the workaround
in handle_xhci_port_status().
Cc: stable@vger.kernel.org
Signed-off-by: George Cherian <george.cherian@cavium.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This definition is used by msecs_to_jiffies in milliseconds.
According to the comments, max rexit timeout should be 20ms.
Align with the comments to properly calculate the delay.
Verified on Sunrise Point-LP and Cannon Lake.
Cc: stable@vger.kernel.org
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The xhci controller on Alpine and Titan Ridge keeps the whole thunderbolt
awake if the host controller is not allowed tp sleep.
This is the case even if no USB devices are connected to the host.
Because of this bigger impact, allow runtime pm as default for these xhci
controllers in the driver.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use soft retry to recover from a USB Transaction Errors that are caused by
temporary error conditions. The USB device is not aware that the xHC
has halted the endpoint, and will be waiting for another retry
A Soft Retry perform additional retries and recover from an error which has
caused the xHC to halt an endpoint.
Soft retry has some limitations:
Soft Retry attempts shall not be performed on Isoch endpoints
Soft Retry attempts shall not be performed if the device is behind a TT in
a HS Hub
Software shall limit the number of unsuccessful Soft Retry attempts to
prevent an infinite loop.
For more details on Soft retry see xhci specs 4.6.8.1
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for the new get_resuming_ports HCD method to
the xhci-hcd driver.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't rely on event interrupt (EINT) bit alone to detect pending port
change in resume. If no change event is detected the host may be suspended
again, oterwise roothubs are resumed.
There is a lag in xHC setting EINT. If we don't notice the pending change
in resume, and the controller is runtime suspeded again, it causes the
event handler to assume host is dead as it will fail to read xHC registers
once PCI puts the controller to D3 state.
[ 268.520969] xhci_hcd: xhci_resume: starting port polling.
[ 268.520985] xhci_hcd: xhci_hub_status_data: stopping port polling.
[ 268.521030] xhci_hcd: xhci_suspend: stopping port polling.
[ 268.521040] xhci_hcd: // Setting command ring address to 0x349bd001
[ 268.521139] xhci_hcd: Port Status Change Event for port 3
[ 268.521149] xhci_hcd: resume root hub
[ 268.521163] xhci_hcd: port resume event for port 3
[ 268.521168] xhci_hcd: xHC is not running.
[ 268.521174] xhci_hcd: handle_port_status: starting port polling.
[ 268.596322] xhci_hcd: xhci_hc_died: xHCI host controller not responding, assume dead
The EINT lag is described in a additional note in xhci specs 4.19.2:
"Due to internal xHC scheduling and system delays, there will be a lag
between a change bit being set and the Port Status Change Event that it
generated being written to the Event Ring. If SW reads the PORTSC and
sees a change bit set, there is no guarantee that the corresponding Port
Status Change Event has already been written into the Event Ring."
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some Renesas controllers get into a weird state if they are reset while
programmed with 64bit addresses (they will preserve the top half of the
address in internal, non visible registers).
You end up with half the address coming from the kernel, and the other
half coming from the firmware.
Also, changing the programming leads to extra accesses even if the
controller is supposed to be halted. The controller ends up with a fatal
fault, and is then ripe for being properly reset. On the flip side,
this is completely unsafe if the defvice isn't behind an IOMMU, so
we have to make sure that this is the case. Can you say "broken"?
This is an alternative method to the one introduced in 8466489ef5
("xhci: Reset Renesas uPD72020x USB controller for 32-bit DMA issue"),
which will subsequently be removed.
Tested-by: Domenico Andreoli <domenico.andreoli@linux.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Faiz Abbas <faiz_abbas@ti.com>
Tested-by: Domenico Andreoli <domenico.andreoli@linux.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We now have 32 different quirks, and the field that holds them
is full. Let's bump it up to the next stage so that we can handle
some more... The type is now an unsigned long long, which is 64bit
on most architectures.
We take this opportunity to change the quirks from using (1 << x)
to BIT_ULL(x).
Tested-by: Domenico Andreoli <domenico.andreoli@linux.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Faiz Abbas <faiz_abbas@ti.com>
Tested-by: Domenico Andreoli <domenico.andreoli@linux.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As we are now using the new port strtuctes the port_arrays
are no longer needed, remove them completely
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't use pointers to port array and port index as function parameters
in xhci_test_and_clear_bit(), just use a pointer to the right port
structure.
xhci_test_and_clear_bit() was the last port_array user in
xhci_get_port_status() and handle_port_status(), so remove the
port_array from them as well.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove old iomem port array and index as parameters, just
send a ponter to a port strucure instread
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
quick way to get the xhci roothub and thus all the ports
belonging to a certain hcd
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current way of having one array telling only the port speed,
and then two separate arrays with mmio addresses for usb2 and usb3 ports
requeres helper functions to transate hw to hcd, and hcd to hw port
numbers, and is hard to expand.
Instead create a structure describing a port, including the mmio address,
the port hardware index, hcd port index, and a pointer to the roothub
it belongs to.
Create one array containing all port structures in the same order the
hardware controller sees them. Then add an array of port pointers to
each xhci hub structure pointing to the ports that belonging to the
roothub.
This way we can easily convert hw indexed port events to usb core
hcd port numbers, and vice versa usb core hub hcd port numbers
to hw index and mmio address.
Other benefit is that we can easily find the parent hcd and xhci
structure of a port structure. This is useful in debugfs where
we can give one port structure pointer as parameter and get both
the correct mmio address and xhci lock needed to set some port
parameter.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On Armada 7K/8K we need to explicitly enable the register clock. This
clock is optional because not all the SoCs using this IP need it but at
least for Armada 7K/8K it is actually mandatory.
The change was done at xhci-plat level and not at a xhci-mvebu.c because,
it is expected that other SoC would have this kind of constraint.
The binding documentation is updating accordingly.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The xHCI controller on various Intel SoCs has an extended cap mmio-range
which contains registers to control the muxing to the xHCI (host mode)
or the dwc3 (device mode) and vbus-detection for the otg usb-phy.
Having a role-sw driver included in the xHCI code (under drivers/usb/host)
is not desirable. So this commit adds a simple handler for this extended
capability, which creates a platform device with the caps mmio region as
resource, this allows us to write a separate platform role-sw driver for
the role-switch.
Note this commit adds a call to the new xhci_ext_cap_init() function
to xhci_pci_probe(), it is added here because xhci_ext_cap_init() must
be called only once. If in the future we also want to handle ext-caps
on non pci xHCI HCDs from xhci_ext_cap_init() a call to it should also
be added to other bus probe paths.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some devices use a clear endpoint halt request as a soft reset, even if
the endpoint is not halted. This will clear the toggle and sequence on the
device side.
xHCI however refuses to reset a non-halted endpoint, so instead
we need to issue a configure endpoint command on xHCI to clear its host
side toggle and sequence, and get it in sync with the device side.
This is a respin of a old patch that was reverted as it had a stale
endpoint context dequeue value which caused regression.
commit 27082e2654 ("xhci: Clear the host side toggle manually when
endpoint is 'soft reset'")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a USB device gets plugged on ASUS PRIME B350M-A's front ports, the
xHC stops working:
[ 549.114587] xhci_hcd 0000:02:00.0: WARN: xHC CMD_RUN timeout
[ 549.114608] suspend_common(): xhci_pci_suspend+0x0/0xc0 returns -110
[ 549.114638] xhci_hcd 0000:02:00.0: can't suspend (hcd_pci_runtime_suspend returned -110)
Delay before running xHC command CMD_RUN can workaround the issue.
Use a new quirk to make the delay only targets to the affected xHC.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For AMD Promontory xHCI host, although you can disable USB ports in
BIOS settings, those ports will be enabled anyway after you remove a
device on that port and re-plug it in again. It's a known limitation of
the chip. As a workaround we can clear the PORT_WAKE_BITS.
[commit and code comment rephrasing -Mathias]
Signed-off-by: Joe Lee <asmt.swfae@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The xHCI driver currently has the IMOD set to 160, which
translates to an IMOD interval of 40,000ns (160 * 250)ns
Commit 0cbd4b34cd ("xhci: mediatek: support MTK xHCI host controller")
introduced a QUIRK for the MTK platform to adjust this interval to 20,
which translates to an IMOD interval of 5,000ns (20 * 250)ns. This is
due to the fact that the MTK controller IMOD interval is 8 times
as much as defined in xHCI spec.
Instead of adding more quirk bits for additional platforms, this patch
introduces the ability for vendors to set the IMOD_INTERVAL as is
optimal for their platform. By using device_property_read_u32() on
"imod-interval-ns", the IMOD INTERVAL can be specified in nano seconds.
If no interval is specified, the default of 40,000ns (IMOD=160) will be
used.
No bounds checking has been implemented due to the fact that a vendor
may have violated the spec and would need to specify a value outside of
the max 8,000 IRQs/second limit specified in the xHCI spec.
Tested-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Adam Wallis <awallis@codeaurora.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Each event segment has been exposed through debugfs. There is no
need to dump ERST content with printk in code. Remove it to make
code more concise and readable.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The content of each register has been exposed through debugfs.
There is no need to dump register content with printk in code
lines. Remove them to make code more concise and readable.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xHCI compatible USB host controllers(i.e. super-speed USB3 controllers)
can be implemented with the Debug Capability(DbC). It presents a debug
device which is fully compliant with the USB framework and provides the
equivalent of a very high performance full-duplex serial link. The debug
capability operation model and registers interface are defined in 7.6.8
of the xHCI specification, revision 1.1.
The DbC debug device shares a root port with the xHCI host. By default,
the debug capability is disabled and the root port is assigned to xHCI.
When the DbC is enabled, the root port will be assigned to the DbC debug
device, and the xHCI sees nothing on this port. This implementation uses
a sysfs node named <dbc> under the xHCI device to manage the enabling
and disabling of the debug capability.
When the debug capability is enabled, it will present a debug device
through the debug port. This debug device is fully compliant with the
USB3 framework, and it can be enumerated by a debug host on the other
end of the USB link. As soon as the debug device is configured, a TTY
serial device named /dev/ttyDBC0 will be created.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch makes some static functions global to avoid duplications
in different files. These functions can be used in the implementation
of xHCI debug capability. There is no functional change.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commands with input contexts are allocated with the
xhci_alloc_command_with_ctx helper.
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a xhci_alloc_command_with_ctx() helper to get rid of
one of the boolean parameters telling if a context should
be allocated with the command.
No functional changes, improves core readability
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.
Update the drivers/usb/ and include/linux/usb* files with the correct
SPDX license identifier based on the license text in the file itself.
The SPDX identifier is a legally binding shorthand, which can be used
instead of the full boiler plate text.
This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_disable_slot() allows the invoker to pass a command pointer
as paramenter. Otherwise, it will allocate one. This will cause
memory leak when a command structure was allocated inside of this
function while queuing command trb fails. Another problem comes up
when the invoker passed a command pointer, but xhci_disable_slot()
frees it when it detects a dead host.
This patch fixes these two problems by removing the command parameter
from xhci_disable_slot().
Fixes: f9e609b824 ("usb: xhci: Add helper function xhci_disable_slot().")
Cc: Guoqing Zhang <guoqing.zhang@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds debugfs consumer for xHCI driver. The debugfs entries
read all host registers, device/endpoint contexts, command ring,
event ring and various endpoint rings. With these entries, users
can check the registers and memory spaces used by a host during
run time, or save all the information with a simple 'cp -r' for
post-mortem programs.
The file hierarchy looks like this.
[root of debugfs]
|__usb
|____[e,u,o]hci <---------[root for other HCIs]
|____xhci <---------------[root for xHCI]
|______0000:00:14.0 <--------------[xHCI host name]
|________reg-cap <--------[capability registers]
|________reg-op <-------[operational registers]
|________reg-runtime <-----------[runtime registers]
|________reg-ext-#cap_name <----[extended capability regs]
|________command-ring <-------[root for command ring]
|__________cycle <------------------[ring cycle]
|__________dequeue <--------[ring dequeue pointer]
|__________enqueue <--------[ring enqueue pointer]
|__________trbs <-------------------[ring trbs]
|________event-ring <---------[root for event ring]
|__________cycle <------------------[ring cycle]
|__________dequeue <--------[ring dequeue pointer]
|__________enqueue <--------[ring enqueue pointer]
|__________trbs <-------------------[ring trbs]
|________devices <------------[root for devices]
|__________#slot_id <-----------[root for a device]
|____________name <-----------------[device name]
|____________slot-context <----------------[slot context]
|____________ep-context <-----------[endpoint contexts]
|____________ep#ep_index <--------[root for an endpoint]
|______________cycle <------------------[ring cycle]
|______________dequeue <--------[ring dequeue pointer]
|______________enqueue <--------[ring enqueue pointer]
|______________trbs <-------------------[ring trbs]
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
XHCI specification 1.1 does not require xHCI-compliant controllers
to always enable hardware USB2 LPM. However, the current xHCI
driver always enable it when seeing HLC=1.
This patch supports an option for users to control disabling
USB2 Hardware LPM via DT/ACPI attribute.
This option is needed in case user would like to disable this
feature. For example, their xHCI controller has its USB2 HW LPM
broken.
Signed-off-by: Tung Nguyen <tunguyen@apm.com>
Signed-off-by: Thang Q. Nguyen <tqnguyen@apm.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit dec08194ff.
Commit dec08194ff ("xhci: Limit USB2 port wake support for AMD Promontory
hosts") makes all high speed USB ports on ASUS PRIME B350M-A cease to
function after enabling runtime PM.
All boards with this chipsets will be affected, so revert the commit.
The original patch was added to stable 4.9, 4.11 and 4.12 and needs
to reverted from there as well
Cc: <stable@vger.kernel.org> # 4.9+
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Read the endpiont ESIT from endpiont context using correct macro.
Add a macro for reading the high bits of ESIT for Large ESIT Payload
Capable hosts (LEC=1)
Cc: <stable@vger.kernel.org> # 4.12
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci driver keeps a bus_state structure for each hcd (usb2 and usb3)
The structure is picked based on hcd speed, but driver only compared
for HCD_USB3 speed, returning the wrong bus_state for HCD_USB31 hosts.
This caused null pointer dereference errors in bus_resume function.
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add PORTSC Port status and control register decoder to
show human readable tracing of portsc register
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add definitions for all port link states defined in xhci
specification for PORTSC register.
Will be needed for human readable port status tracing
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When USB Ethernet is plugged in ASMEDIA ASM1042A xHCI host, bad
performance was manifesting in Web browser use (like download
large file such as ISO image). It is known limitation of
ASM1042A that is not compatible with driver scheduling,
As a workaround we can modify flow control handling of ASM1042A.
The register we modify is changes the behavior
[use quirk bit 28, usleep_range 40-60us, empty non-pci function -Mathias]
Cc: <stable@vger.kernel.org>
Signed-off-by: Jiahau Chang <Lars_chang@asmedia.com.tw>
Signed-off-by: Ian Pilcher <arequipeno@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some remaining USB fixes for 4.13-rc1. They were originally
scheduled for 4.12-final, but I didn't send them to you in time.
Because of that, they were in a separate branch from the larger USB set
of patches, so here they are in a separate pull request.
Nothing major here a all, just 3 small patches:
- some usb-serial new device ids
- xhci bugfix for some crazy AMD hardware
All of these have been in linux-next for a long time with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWV9FRg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylHxgCfTT31v4FaxH2k76qA1ZnHdXWHqyQAn3oyOE4T
uJhpp1FbFR1VNXM/jRox
=PCPm
-----END PGP SIGNATURE-----
Merge tag 'usb-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some remaining USB fixes for 4.13-rc1. They were originally
scheduled for 4.12-final, but I didn't send them to you in time.
Because of that, they were in a separate branch from the larger USB
set of patches, so here they are in a separate pull request.
Nothing major here a all, just three small patches:
- some usb-serial new device ids
- xhci bugfix for some crazy AMD hardware
All of these have been in linux-next for a long time with no reported
issues"
* tag 'usb-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
xhci: Limit USB2 port wake support for AMD Promontory hosts
USB: serial: qcserial: new Sierra Wireless EM7305 device ID
USB: serial: option: add two Longcheer device ids
For AMD Promontory xHCI host, although you can disable USB 2.0 ports in
BIOS settings, those ports will be enabled anyway after you remove a
device on that port and re-plug it in again. It's a known limitation of
the chip. As a workaround we can clear the PORT_WAKE_BITS.
This will disable wake on connect, disconnect and overcurrent on
AMD Promontory USB2 ports
[checkpatch cleanup and commit message reword -Mathias]
Cc: <stable@vger.kernel.org>
Cc: Tsai Nicholas <nicholas.tsai@amd.com>
Signed-off-by: Jiahau Chang <Lars_Chang@asmedia.com.tw>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Get rid of stopped_stream member in virtual endpoint structure as
it is only used in one case when cleaning a halted endpoint.
Pass it as function parameter instead.
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci supports soft retry recovery when the host halted the host side of an
endopint but the connected USB device is not aware of the halt.
In this case xhci needs to issue a reset endopint command with a TSP
(Transfer State Preserve) flag set which preserves the Data toggle
and Sequence number of the endpoint.
This feature is needed to handle a few special transfer event types
such as USB Transaction error that don't always point to a causing TRB.
see xhci 4.6.8.1 for more details
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Anurag Kumar Vulisha reported several issues with xhci endpoint
ring caching.
31 Rings are cached per device before a ring is freed.
These cached rings are not used as default if a new ring is needed.
They are only used if the driver fails to allocate memory for a ring.
The current ring cache is more a reason to why we run out memory than a
help when we actually do so.
Anurag Kumar Vulisha tried to use cached rings as a first option and
found new issues with cached ring initialization.
Cached rings were first zeroed and then manually reinitialized with link
trbs etc, but forgetting to set some important bits like cycle toggle bit.
Remove the ring cache completely as it's a faulty premature optimization
eating memory
Reported-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Tested-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The values for the new dequeue segment, new dequeue pointer and new cycle
state are needed for manually moving the xHC ring dequeue pointer.
These are conveniently stored in a xhci_dequeue_state structure.
stream support was added later and stream_id was carried
as a function parameter.
Move the stream_id to the xhci_dequeue_state structure instead.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We no longer keep track of where we stopped in a stopped_td pointer.
We get the ring dequeue pointer from the endpoint or stream context
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The #ifdef is slightly wrong as it doesn't cover the xhci_priv_resume_quirk()
function, causing a harmless warning:
drivers/usb/host/xhci-plat.c:58:12: error: 'xhci_priv_resume_quirk' defined but not used [-Werror=unused-function]
static int xhci_priv_resume_quirk(struct usb_hcd *hcd)
A simpler way to do this correctly is to use __maybe_unused annotations
that let the compiler silently drop the functions when there is no
reference.
Fixes: b0c69b4bac ("usb: host: plat: Enable xHCI plat runtime PM")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We already have sp_array to store each scratch buffer address for xHC,
it doesn't need another sp_dma_buffers array to store it.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the modern API to request MSI or MSI-X interrupts, which allows us to
get rid of the msix_entries array, as well as cleaning up the cleanup
code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As per [1] issue #4,
"The periodic EP scheduler always tries to schedule the EPs
that have large intervals (interval equal to or greater than
128 microframes) into different microframes. So it maintains
an internal counter and increments for each large interval
EP added. When the counter is greater than 128, the scheduler
rejects the new EP. So when the hub re-enumerated 128 times,
it triggers this condition."
This results in Bandwidth error when devices with periodic
endpoints (ISO/INT) having bInterval > 7 are plugged and
unplugged several times on a TUSB73x0 XHCI host.
Workaround this issue by limiting the bInterval to 7
(i.e. interval to 6) for High-speed or faster periodic endpoints.
[1] - http://www.ti.com/lit/er/sllz076/sllz076.pdf
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_decode_trb() treats a link trb in the same way as that for
an event trb. This patch fixes this by decoding the link trb
according to the spec.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
XHCI context changes have already been traced by the trace
events. It's unnecessary to put the same message in kernel
log. This patch removes the use of xhci_dbg_ctx().
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Every XHCI TRB has already been traced by the trb trace events.
It is unnecessary to put the same message in kernel log. This
patch removes xhci_debug_trb().
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
XHCI ring changes have already been traced by the ring trace
events. It's unnecessary to put the same messages in kernel
log. This patch removes the debugging code for a ring.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
enq_updates and deq_updates were introduced in the first place
to check whether an xhci hardware is able to respond to trbs
enqueued in the ring. We now have trb tracers to trace every
single enqueue/dequeue trb. It's time to remove them and the
associated debugging code.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several functions have a single user in the same file where it
is defined. There's no need to expose it anywhere else.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_dbg_ep_rings() isn't used in xhci driver anymore. Remove
it to reduce the module binary size.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce a new xhci_hc_died() function that takes care of handling
pending commands and URBs if a host controller becomes unresponsive.
This addresses issues on hotpluggable xhci controllers that disappear
from the bus suddenly, often while the bus (PCI) remove function is
still being processed.
xhci_hc_died() sets a XHCI_STATUS_DYING flag to prevent new URBs and
commands or to be queued. The flag also ensures xhci_hc_died() will
give back pending commands and URBs once.
Host is considered dead if register read returns 0xffffffff, or host
fails to abort the command ring, or fails stopping an endpoint after
trying for 5 seconds.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Format for each TRB in each control transfer stage differs. Let's make
sure we correctly pretty print these fields to avoid confusion.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With these, we can track what's happening with the HW while executing
each and every command. It will give us visibility into how the
different contexts are being modified by xHC which can bring insight
into problems while debugging.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By extracting and exposing xhci_slot_state_string() in a header file, we
can re-use it to print Slot Context State from our tracepoints, which
can aid in tracking down problems related to command execution.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For usb2 ports, the port test mode Test_J_State, Test_K_State,
Test_Packet, Test_SE0_NAK and Test_Force_En can be enabled
as described in usb2 spec.
USB2 test mode is a required hardware feature for system integrators
validating their hardware according to USB spec, regarding signal
strength and stuff. It is purely a hardware test feature.
Usually you need an oscilloscope and have to enable those test modes on
the hardware. This will send some specific test patterns on D+/D-. There
is no report available (in Linux itself) as it is purely externally
visible. Regular USB usage is not possible at that time.
Anyone (well access to e.g. /dev/bus/usb/001/001 provided) can use it by
sending appropriate USB_PORT_FEAT_TEST requests to the hub.
[Add better commit message by Alexander Stein -Mathias]
Signed-off-by: Guoqing Zhang <guoqing.zhang@intel.com>
Cc: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Change the visability of xhci_start() so that it
can be used when enabling test mode.
Signed-off-by: Guoqing Zhang <guoqing.zhang@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactoring slot disable related code into a helper
function xhci_disable_slot() which can be used when
enabling test mode.
Signed-off-by: Guoqing Zhang <guoqing.zhang@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of storing a zero length array of td pointers, and then
allocate memory both for the td pointer array and the td's, just
use a zero length array of actual td's in urb private data.
old:
struct urb_priv {
struct xhci_td *td[0]
}
new:
struct urb_priv {
struct xhci_td td[0]
}
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
urb_priv structure has a count on how many TDs the
URB contains, and how many of those TD's we have handled.
rename:
length -> num_tds
td_cnt -> num_tds_done
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
instead of having a tracer that can only trace command completions,
let's promote this tracer so it can trace and decode any TRB.
With that, it will be easier to extrapolate the lifetime of any TRB
which might help debugging certain issues.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we just provide a helper to convert completion code to string, we can
combine all debugging messages into a single print.
[keep the old debug messages, for warn and grep -Mathias]
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
